ORIGINAL INSTRUCTIONS

USER’S MANUAL
AIR-CONDITIONER USER’S MANUAL ENGLISH
AIR-CONDITIONER

MANUEL DE L’UTILISATEUR FRANÇAIS

CLIMATISEUR

ANWENDERHANDBUCH DEUTSCH
KLIMAGERÄT

SRK20ZSX-S
ISTRUZIONI PER L’USO ITALIANO
CONDIZIONATORE D’ARIA
SRK25ZSX-S
SRK35ZSX-S
SRK50ZSX-S MANUAL DEL PROPIETARIO ESPAÑOL
SRK60ZSX-S ACONDICIONADOR DE AIRE

GEBRUIKERSHANDLEIDING NEDERLANDS
AIRCONDITIONING

MANUAL DO UTILIZADOR PORTUGUÊS

APARELHO DE AR CONDICIONADO

ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ ΕΛΛΗΝΙΚΑ

ΚΛΙΜΑΤΙΣΤΙΚΟ

РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ РУССКИЙ

КОНДИЦИОНЕР ВОЗДУХА

KULLANIM KILAVUZU TÜRKÇE

MITSUBISHI HEAVY INDUSTRIES THERMAL SYSTEMS, LTD.

16-5 Konan 2-chome, Minato-ku, Tokyo, 108-8215, Japan
http://www.mhi-mth.co.jp/en/

MITSUBISHI HEAVY INDUSTRIES AIR-CONDITIONING EUROPE, LTD.

7 Roundwood Avenue, Stockley Park, Uxbridge, Middlesex, UB11 1AX, United Kingdom
Tel : +44-20-7025-2750
Fax: +44-20-7025-2751
http://www.mhiae.com/

MITSUBISHI HEAVY INDUSTRIES AIR-CONDITIONERS AUSTRALIA, PTY. LTD.

9C Commercial Road Kingsgrove NSW 2208 PO BOX 318 Kingsgrove NSW 1480
Tel : +61-2-8571-7977
Fax: +61-2-8571-7992
https://www.mhiaa.com.au/

RLF012A201
201610

RLF012A201_Cover.indd 1 10/28/2016 2:54:35 PM

 Thank you for purchasing a MITSUBISHI HEAVY INDUSTRIES THERMAL SYSTEMS, LTD.
Air-Conditioner. To get the best long-lasting performance, please read and follow this user’s manual
carefully before using your air-conditioner. After reading, please store the manual in a safe place
and refer to it for operational questions or in the event of any irregularities.
This air-conditioner is intended for domestic use.
This Product contains fluorinated greenhouse gases.
Do not vent R410A into the atmosphere: R410A is a fluorinated greenhouse gas with
a Global Warming Potential (GWP) = 2088.
Refer to a label on outdoor unit for the weight of fluorinated greenhouse gas and CO2
equivalent.
ENGLISH

Your air-conditioner is marked with this symbol. It means that waste electrical and
electronic equipment (WEEE as in directive 2012/19/EU) should not be mixed with
general household waste. Air-conditioner should be treated at an authorized treat-
ment facility for re-use, recycling and recovery and not be disposed of in the munici-
pal waste stream. Please contact the installer or local authority for more information.

This symbol printed on the batteries attached to your air-conditioner is information

for end-users according to the EU directive 2006/66/EC article 20 annex II.
Batteries, at their end-of-life, should be disposed of separately from general house-
hold waste. If a chemical symbol is printed beneath the symbol
shown above, this chemical symbol means that the batteries contain a
heavy metal at a certain concentration. This will be indicated as follows:
Hg:mercury(0.0005%), Cd:cadmium(0.002%), Pb:lead(0.004%)
Please, dispose of batteries correctly at your local community waste
collection or the recycling center.
The emission sound pressure level from each Indoor and Outdoor unit is under 70 dB(A).

contents
Safety precautions ..........................................2 OFF TIMER operation ..................................17
Tips for effective operation .............................5 ON TIMER operation ....................................18
Name of each part and its function.................6 SLEEP TIMER + ON TIMER operation ........18
Remote control ...............................................8 ON TIMER + OFF TIMER operation ............19
Operation failure with the remote control ........8 ALLERGEN CLEAR operation .....................19
Temporary run operation ................................8 WEEKLY TIMER operation ..........................20
Installing two air-conditioners HIGH POWER/ECO operation .....................24
in the same room ............................................9 NIGHT SETBACK operation .........................25
Child lock ........................................................9 SILENT operation .........................................25
Airflow range setting .....................................10 MENU function
Operation and display section Display brightness adjustment ...................26
for remote control .........................................12 AUTO OFF operation .................................27
Current time setting .....................................13 SELF CLEAN operation .............................28
AUTO mode operation ..................................13 PRESET operation ....................................28
Temperature adjustment during AUTO mode...14 Maintenance .................................................29
FAN SPEED .................................................14 Proper installation .........................................31
COOL/HEAT/DRY/FAN mode operation .......15 Troubleshooting ...........................................31
Air-conditioner operation temperature range ....15 Notice ...........................................................32
Characteristics of HEAT mode operation......15 Contact your dealer ......................................33
Airflow direction adjustment..........................16 Auto restart function .....................................33
3D AUTO operation ......................................16 About the multiple air-conditioners ...............33
SLEEP TIMER operation ..............................17 Self diagnosis function..................................34

–1–

RLF012A201_EN_1-34.indd 1 10/28/2016 12:36:35 PM

 Safety precautions
• Before starting to use the system, please read these “Safety precautions” carefully to ensure
proper operation of the system.
• When you have read this user’s manual, please keep it safely. If someone else takes over as
user, make sure that the manual is also passed on to the new user.
Indicates a potentially hazardous situation which, if not avoided, can
WARNING result in serious consequences such as death or severe injury.
Indicates a potentially hazardous situation which, if not avoided, can
CAUTION result in personal injury or property damage.

Please observe these precautions with great care, since they are essential to your safety.
• Symbols which appear frequently in the text have the following meaning:

Observe instructions Provide proper

Strictly prohibited
with great care earthing

❚ INSTALLATION PRECAUTIONS
WARNING
• The system is for domestic and residential use.
If used in severe environments, such as an engineering workplace, the equipment may
function poorly.
• The system must be installed by your dealer or a qualified installer.
It is not advisable to install the system by yourself, as faulty handling may cause
leakage of water, electric shock or fire.
CAUTION
• Do not install it where flammable gas may leak.
Gas leaks may cause fire.
• Make sure that an earth leakage • Make sure to install the drain hose
breaker is installed. properly so that all the water is drained
If you do not install an earth leakage out.
breaker, you may get an electric shock. Improper installation may lead to water
drop in the room resulting in wet furniture.
• Make sure that the system has been properly earthed.
Earth wire should never be connected to a gas pipe, water pipe, lightning conductor
or telephone earth wire. Improper installation of the earth wire may cause an electric
shock.

–2–

RLF012A201_EN_1-34.indd 2 10/28/2016 12:36:36 PM

 ❚ Safety precautions

❚ OPERATION PRECAUTIONS
WARNING
• Children shall not play with the • Cleaning and user maintenance shall
air-conditioner. not be made by children without
• Do not expose yourself to the cooling supervision.
air for a long period. • Do not insert anything into the air
This could affect your physical condition outlet.
and cause health problems. This may cause injury, as the internal fan
rotates at high speed.
• This air-conditioner can be used by children aged from 8 years and above
and people with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, if they have been given supervision or instruction
concerning use of the air-conditioner in a safe way and understand the hazards
involved.
• Store the remote control out of reach of children.
Failure to observe this may result in the batteries being swallowed or other accidents.
CAUTION
• Only use approved fuses. • Do not use for preservation of food,
Use of steel or copper wire instead of an plants or animals, precision devices or
approved fuse is strictly prohibited, as it works of art.
may cause a breakdown or fire. The system is only intended for use in
• Do not handle the switches with wet ordinary domestic rooms. Any other use
hands. of the system may damage the quality of
This may cause an electric shock. food, etc.
• Do not swing from the indoor unit. • Do not place anything containing
If the indoor unit falls down,you may get water, like vases, on top of the unit.
injured. Water entering the unit could damage the
• Do not place a flammable insecticide insulation and therefore cause an electric
or paint spray near the air-conditioner, shock.
nor spray it directly on the system. • Do not install the air-conditioner where
This may result in a fire. the airflow direction is aimed directly at
• Do not expose any combustion plants or animals.
appliance directly to the air stream of This will damage their health.
the air-conditioner. • Do not sit on the outdoor unit nor put
The combustion appliance may anything on it.
malfunction. If the unit falls down or things drop from it,
• Do not wash the air-conditioner with people could get hurt.
water. • After a long period of use, check the
This could cause an electric shock. unit’s support structure regularly.
Using a high pressure washer may cause If you do not repair any damage right
damage to the aluminum fins, resulting in away, the unit may fall down and cause
performance decrement. personal injury.

–3–

RLF012A201_EN_1-34.indd 3 10/28/2016 12:36:37 PM

 ❚ Safety precautions

CAUTION
• Do not touch the aluminum fins on the • Do not shut off the power source
heat exchanger. immediately after stopping the
It may result in injury. operation.
• Do not place household electrical Wait at least 5 minutes, otherwise there is
appliances or household items under- a risk of water leakage or breakdown.
neath the indoor or outdoor units. • Do not control the system with main
Condensation falling from the unit may power switch.
stain objects and cause accidents or It can cause fire or water leakage. In
electrical shock. addition, the fan can start unexpectedly,
• Do not operate the system without the which can cause personal injury.
air filter. • Do not pour liquid into the unit and do
It can cause malfunction of the system not put water container on the unit.
due to clogging of the heat exchanger. Water entering the unit could damage the
insulation and therefore cause an electric
shock.
• If you operate air-conditioner together • Contact your dealer to clean inside the
with a combustion appliance, you must indoor unit, do not attempt to do by
regularly ventilate the indoor air. yourself.
Insufficient ventilation may cause The use of a non-approved detergent or
accidents due to oxygen deficiency. improper washing method may damage
• Stand firmly on a stepladder or other the unit’s plastic components and cause
stable object when removing the inlet leaks. Damage, smoke, or fire may also
panel and filters. happen if the detergent comes in contact
Failure to observe this may result in injury with electrical parts or the unit’s motor.
through insecure objects toppling over. • Stop the unit and turn off the power if
• When you clean air-conditioner, stop you hear thunder or there is a danger
the unit and turn off the power source. of lightning.
Never open the panel while the internal It may damage the unit.
fan is rotating. • If the power cable becomes damaged,
• Do not place objects near the outdoor contact your dealer or a qualified
unit or allow leaves to gather around installer.
the unit. If it is not replaced, it may cause a
If there are objects or leaves around the breakdown or fire.
outdoor unit, small animals may enter
unit and contact electrical parts and may
cause a break-down, smoke or fire.

–4–

RLF012A201_EN_1-34.indd 4 10/28/2016 12:36:37 PM

 ❚ Safety precautions

❚ PRECAUTIONS FOR RELOCATION OR REPAIRS

WARNING
• Do not perform any repairs or modifications by yourself. Consult the dealer if the
unit requires repair.
If you repair or modify the unit, it can cause water leaks, electric shocks or fire.
• Consult your dealer for repairs. • If the air-conditioner fails to cool
Wrong repairs could cause an electric or warm the room, it may have a
shock, fire, etc. refrigerant leakage. Contact your
• In case the air-conditioner is relocated dealer.
elsewhere, contact your dealer or a If refrigerant needs to be added,
qualified installer. check with your dealer for proper
Faulty installation may cause water instructions.
leakage, electric shock, fire, etc. If the refrigerant comes in contact with the
• If you notice anything abnormal (smell bare skin, it may cause cold injury.
of burning, etc.), stop the system, turn If the refrigerant gas is inhaled
off the power source and consult your excessively, it may cause deterioration
dealer. of nerve function like dizziness and
Continued use of the system in headache, or deterioration of heart
abnormal circumstances can result in function like irregular heartbeat and heart
malfunctioning, electric shock, fire, etc. palpitation temporarily. If refrigerant
unexpectedly leaks from the unit onto
a fan heater, stove, hotplate or other
heat source, harmful gases could be
generated.

Tips for effective operation

■ Please observe the following for the most economic and comfortable use of your unit.
• Set a suitable room temperature.
Excessively high or low temperatures are not good for your health and waste of electricity.
• Clean the filters frequently.
Clogged filters may block the airflow and cause less efficient operation. Page 29
• Avoid direct sunlight and draught.
Cut out direct sunlight by drawing the curtains or blinds when cooling. Keep windows and doors shut, except when ventilating.
• Adjust the airflow direction properly.
Adjust the up/down and left/right airflow to ensure a steady room temperature.
• Operate the unit only when needed.
Use the timer properly to operate the unit only when needed.
• Keep heat source away when cooling.
Keep heat sources out of the room as much as possible.

–5–

RLF012A201_EN_1-34.indd 5 10/28/2016 12:36:37 PM

 Name of each part and its function
INDOOR UNIT
Air-cleaning filter
Air inlet panel Air inlet Room temperature Page 30
sensor
Page 29
• Allergen clear filter
(Light orange)

Air filters
Page 29

• Photocatalytic washable
Fan deodorizing filter (Orange)
• Inside of
the unit

Heat exchanger Air outlet

(Aluminum fin) Motion sensor
SPLIT TYPE ( INDOOR UNIT )
Louvers MODEL
(Vertical blades) Unit display SERVICE CODE
• Left / right airflow section POWER SUPPLY
direction adjustment Page 7

Flaps
(Horizontal blades)
• Up / down airflow
direction adjustment Model name

OUTDOOR UNIT
WARNING CAUTION

Air inlet
(back and side) MOVING FAN BLADES SHARP EDGE OF FINS
DO NOT INSERT ANYTHING DO NOT TOUCH THE
DO NOT STEP ON TOP OF THIS UNIT.
INTO THE AIR OUTLET. ALUMINUM FINS.
IT MIGHT CAUSE INJURY. IT MIGHT CAUSE INJURY. IT MIGHT CAUSE INJURY.

Model name label

(SRC20~35ZSX-S)

Model name

Refrigerant pipe
Fan and electric wire
• Inside of the unit Don't touch
Drain hose
the terminal
block.

Don't touch
refrigerant
Model name label pipings and
(SRC50~60ZSX-S) connections.

Heat exchanger Drain hole Air outlet

(Aluminum fin)

–6–

RLF012A201_EN_1-34.indd 6 10/28/2016 12:36:37 PM

 Name of each part and its function

Unit display section

TIMER light (yellow)
Unit ON/OFF button Illuminates during TIMER operation.
This button can be used for turning on/off Page 17~23
the unit when a remote control is not available.
Page 8
RUN light (green)

Remote control signal receiver

• Illuminates during operation.
• Blinks slowly when SELF CLEAN operation
(3 seconds ON, 1 second OFF).

Page 28

• RUN lights blink quickly during invalid operation mode. • Blinks when airflow is stopped to
Page 33 prevent blowing out of cold air in
heating operation. (1.5 seconds ON,
0.5 seconds OFF)

Page 32

• Blinks slowly when AUTO OFF

operation during stand by (3.5
seconds ON, 0.5 second OFF).
Page 27

Accessories

Battery ×2 Allergen clear filter

(R03 (AAA, Micro)) (Light orange)

Remote control Remote control Wood screw ×2 Photocatalytic washable

holder (for remote control holder mounting) deodorizing filter (Orange)

CAUTION
• Do not touch the air inlet panel and flap while it is operating.
- The air inlet panel opens up while the system is operating.
Do not install the unit in a fashion in which the air inlet panel cannot open or place
objects near the indoor unit.
- The air inlet panel and the flap close when the operation stops.
Your fingers may get caught when the panel or the flap closes.
• Do not apply excessive force to the air inlet panel and flap. Doing so may cause
these parts to malfunction.

NOTE

• Buzzer sound for remote control

Buzzer sound (PipPip) is produced when
preset temperature is set to 24 °C or,
AUTO operation mode is selected or,
automatic airflow is selected.

Buzzer sound (Pip) is produced when

air-conditioner is turned off by pressing ON/OFF button (except SELF CLEAN mode).

Airflow setting Preset temperature

Pip Pip Pip Pip Pip Pip Pip Pip Pip Pip Pip Pip

–7–

RLF012A201_EN_1-34.indd 7 10/28/2016 12:36:38 PM

 Remote control
Setting the batteries
NOTE

1 Pull out the cover. • Do not use old and new batteries together.
• Remove the batteries when the remote control is not used for a long period.
• The recommended effective period of a battery conforming to JIS or IEC
2 Insert new batteries.
R03 (AAA, Micro) x2
should be 6 to 12 months with normal use. If used longer, or when an
unspecified battery is used, liquid may leak from the battery, causing the
Pay attention to remote control to malfunction.
the and • The recommendable effective period is printed on the battery. This may be
marks shorter due to manufacturing time to the unit. However, the battery may still
be in working order after expiry of its nominal life.

■ When the display shows any abnormal condition, press the ACL switch with the
tip of a ballpoint pen.

Using the remote control holder

3 Close the cover.
The remote control can be attached to a wall or pillar
by using the remote control holder. Before installing the
remote control, check that the air-conditioner receives
4 Press the ACL switch with
the tip of a ballpoint pen.
• Set the current time.
the signals properly.

For installing or removing the remote control, move it up

Page 13 Step 2 or down in the holder.

The following cases show exhausted batteries. Replace old batteries with new ones.
• Receiving beep is not emitted when a signal is transmitted.
• Display fades away.

Warning note for remote control

Strictly prohibited
• Do not take remote control near • Do not leave the remote control • Do not drop the remote control.
high temperature places, such as an exposed to direct sunlight or other Handle with care.
electric heating carpet or a stove. strong lighting.

• Do not put any obstructing • Do not spill any liquid on the • Do not place heavy objects on the
obstacles between the remote remote control. remote control, or step on it.
control and the unit.

Operation failure with the remote control

• Are the batteries running down? • If the operation fails, operate the unit with Below
temporary run operation function.
“Setting the batteries” above. Contact your dealer to have the remote
Replace the batteries with new ones and retry the control checked.
operation.

Temporary run operation

• The unit ON/OFF button on the unit operates ON/OFF temporarily when the remote control is not used.
Operation program
• OPERATION MODE : AUTO
• FAN SPEED : AUTO
• AIR FLOW : AUTO
• Operation starts by pressing the unit ON/OFF button; it stops if you press
the button again.
Unit ON/OFF button

NOTE

• Do not keep pressing the unit ON/OFF button down for 5 seconds or more.
(Pressing it 5 seconds or more sets the forced cooling operation used during servicing or when relocating the air-conditioner.)

–8–

RLF012A201_EN_1-34.indd 8 10/28/2016 12:36:39 PM

 Installing two air-conditioners in the same room
■ When two air-conditioners are installed in the same room, use this setting when the two air-conditioners are not operated with one remote
control. Set the remote control and indoor unit.

Setting the remote control Setting an indoor unit

1 Pull out the cover and take out

batteries. 1 Turn off the power source and turn it on after 1 minute.

2 Disconnect the switching line next to

the battery with wire cutters. 2 Point the remote control (that was set according to the
procedure described on the left side) at the indoor unit
and send a signal by pressing the ACL switch on the
remote control.
Since the signal is sent in
about 6 seconds after the Reception
peep
ACL switch is pressed,
point the remote control
at the indoor unit for some
time.

Disconnect

3 Insert batteries.
Close the cover.
3 Check that the reception buzzer sound “peep” is emit-
ted from the indoor unit.
At completion of the setting, the indoor unit emits a buzzer sound
“peep”. (If no reception sound is emitted, start the setting from the
beginning again.)

Child lock
■ This function locks the remote control operation to prevent an operation error.

1 Press the SET button for 3 seconds or more.

is displayed. When Child lock is set, only the ON/OFF button can be
operated.

Releasing procedure

Turn off the light by pressing the SET button for 3 seconds or more.

NOTE

• While Child lock is set, the settings of temperature, fan speed and airflow
direction cannot be changed. To change the settings, reset Child lock.
• Child lock will not function during ALLERGEN CLEAR operation.

–9–

RLF012A201_EN_1-34.indd 9 10/28/2016 12:36:40 PM

 Airflow range setting
■ Take the air-conditioner location into account and adjust the left/right airflow range to maximize air-conditioning.

1 If the air-conditioner is running, press the ON/OFF

button to stop.
The airflow range setting cannot be made while the unit is running.

2 Press the AIR FLOW U/D (UP/DOWN) button and

the AIR FLOW L/R (LEFT/RIGHT) button together for
5 seconds or more.
The airflow range setting display illuminates.

3 Setting the airflow range.

Press the AIR FLOW L/R (LEFT/RIGHT) button and adjust to the desired
location.
Each time the AIR FLOW L/R (LEFT/RIGHT) button is pressed, the display is
switched in the order of:

(Center Installation) (Right End Installation) (Left End Installation)

4 Press the ON/OFF button.

The air-conditioner’s airflow range is set.
Press within 60 seconds of setting the airflow range (while the airflow range
setting display illuminates).

Air-conditioner installation location and airflow range

The diagram below indicates the airflow ranges corresponding to the air-conditioner’s installation location. Consider your room’s layout
and set the airflow range to maximize air-conditioning.

Airflow range Airflow range Airflow range

(Left End Installation) (Center Installation) (Right End Installation)

NOTE

• Once the airflow range setting is configured, it is stored in the air-conditioner even if the power source is turned off. To change the
airflow range setting, set range again with the remote control.
• During the operation, an airflow range setting cannot be set.
• When the air-conditioner is installed at the location within 50 cm from the wall, it is recommended to change the airflow range setting
to “Right End Installation” or “Left End Installation”.

– 10 –

RLF012A201_EN_1-34.indd 10 10/28/2016 12:36:41 PM

 Motion sensor setting
■ According to the installation location of the indoor unit, turn the sensor to the right or left until it clicks into position.
(The orientation of the application range can be changed laterally by approximately 20 degrees.)

Left End Installation Center Installation Right End Installation

1 Open the air inlet panel.
page 29
Air-conditioner
installation
location
2 Change the orientation of the motion
sensor.

Motion sensor
orientation

Turn to the right Center Turn to the left

Adjust the orientation of the motion sensor by pressing

the end of the sensor.

3 Close the air inlet panel.

page 29

About the motion sensor

■ The motion sensor detects the movement of people (heat-generating bodies) to determine whether there is someone in the room and
how much they move.
The application range is as follows. Adjust the angle of the motion sensor according to the installation location of the indoor unit.
above
• Horizontal angle 100°(Top view)
50° 50°
7m

• Depending on the room conditions and/or the installation location, the motion sensor may not be able to detect people correctly.
The motion sensor may not be able to detect people in the following cases:
− When a person(s) is immediately under or beside the air-conditioner
− When the room temperature is 30°C or higher
− When there is any obstacle such as furniture or a glass window between the air-conditioner and the person(s)
− When the person(s) is covering most of their skin with extremely heavy clothes or they are exposing their backs to the air-
conditioner
- When the person(s) makes extremely little movement, which may occur while, for example, they are sleeping
• In the following cases, the motion sensor may judge that there is someone in the room even though there is actually not:
− When there is an animal such as a dog or cat in the room
− When plant leaves are swaying in the wind
− When a heating appliance (e.g., oscillating heater) or other heat-generating object is moving
− When there is a significant temperature change in walls or floors of the room at the time the operation starts

– 11 –

RLF012A201_EN_1-34.indd 11 10/28/2016 12:36:41 PM

 Operation and display section for remote control
Transmission section

OPERATION MODE select button ON/OFF (luminous) button

Each time the button is pressed, the Press to start operation, press again
mode changes. to stop.
Page 13,15

TEMPERATURE button FAN SPEED button

This button sets the room temperature. Each time the button is pressed, the fan
speed changes.
Page 14

HI/ECO button AIR FLOW (UP/DOWN) button

This button changes the HIGH POWER/ This button changes the airflow (up/
ECO operation. down) direction.
Page 24 Page 16

AIR FLOW (LEFT/RIGHT) button 3D AUTO button

This button changes the airflow (left/ This button sets 3D AUTO operation.
right) direction. Page 16
Page 16

SILENT button NIGHT SETBACK button

This button sets the SILENT operation. This button sets NIGHT SETBACK
operation.
Page 25
Page 25

ALLERGEN CLEAR button SET/Child lock button

This button selects ALLERGEN CLEAR Use this button to set the timer and
operation. Child lock.
Page 19 Page 9

ON TIMER button CANCEL button

This button cancels the ON timer, OFF
This button selects ON TIMER operation.
timer, and SLEEP operation.
Page 18

OFF TIMER button TIMER button

This button selects OFF TIMER
This button is used for setting the current
operation.
time and timer function.
Page 17

WEEKLY button PROGRAM button

This button switches the WEEKLY This button sets WEEKLY TIMER.
TIMER to ON/OFF. Page 20
Page 20
[View with the cover opened]
MENU switch ACL switch
This switch selects the brightness This switch resets the program to default
adjustment, AUTO OFF operation, SELF state. Page 8, 13
CLEAN operation and PRESET operation.
Page 26
TIME SET UP switch
SLEEP button The above illustration shows all controls, but in practice This switch is used for setting the time.
only the relevant parts are shown.
This button selects SLEEP operation. Page 13
Page 17

Display in OFF status

Transmission procedure
The current time, day of the week, When each button on the remote control is
and present OPERATING MODE are pressed – with the remote control pointing
displayed while the air-conditioner is towards the air-conditioner unit, a signal is
turned off. transmitted.
When the air-conditioner receives the signal
correctly, it will beep.

– 12 –

RLF012A201_EN_1-34.indd 12 10/28/2016 12:36:42 PM

 Current time setting
■ When inserting the batteries, the current time is automatically set to time setting mode. Mon and 13:00 are displayed as the current time.
Set a correct day of the week and time.
Example: Set to Sat 10:30.

1 Press the TIME SET UP switch.

Press with the tip of a ballpoint pen, etc.
The day of the week display blinks, enabling the setting of a day of the week.

2 Press the “ or
(Set to Sat)
(TIMER)” button.

3 Press the SET button.

The day of the week display changes from blinking to steady lighting,
completing the setting of a day of the week, and the time display blinks.
Make sure to press the button within 60 seconds from the last operation in
step 2, otherwise the day of the week will not be set.

4 Press the “ or
(Set to 10:30)
(TIMER)” button.

5 Press the SET button.

The time display changes from blinking to steady lighting and the setting is
complete.
Make sure to press the button within 60 seconds from the last operation in
step 4, otherwise the time will not be set.

NOTE

• The timer operation works based on the time clock, so set it • When the battery of the remote control is replaced or the ACL
correctly. switch is pressed, the remote control will be set to the initial
• The remote control data will be reset when the present time is state. Since the WEEKLY TIMER program is not set in the initial
set. state, set the program according to the setting procedure.

AUTO mode operation

■ Automatically selects the operation mode (COOL, HEAT) depending on the room temperature when switched on.

1 Press the MODE button.

The mode changes whenever the button is pressed.
Set to .

2 Press the ON/OFF button.

To stop: Press the ON/OFF button.

NOTE
• If you do not want the AUTO mode program, change
• In case air is not blowing out
to COOL, HEAT or FAN instead of AUTO.
during the operation.
Page 32 Page 15
• Airflow direction adjustment procedure.
Page 16

– 13 –

RLF012A201_EN_1-34.indd 13 10/28/2016 12:36:42 PM

 Temperature adjustment during AUTO mode
■ Default preset temperature during AUTO mode is 24°C for both cooling and heating mode. However, it can be adjusted (Minimum 18°C,
Maximum 30°C) using button or button.

1 Press the“ or (TEMP)” button.

When it is a little cold

Press the button.

■ Each time the button is pressed, the switch over occurs in the following order
18 → 19 → ............ 23 → 24 → 25 ......... → 30.
When 30 is indicated, even if the button is pressed, the indicator does not change.
When it is a little hot

Press the button.

■ Each time the button is pressed, the switch over occurs in the following order
30 → 29 → ............ 25 → 24 → 23 ......... → 18.
When 18 is indicated, even if the button is pressed, the indicator does not change.

FAN SPEED
■ The FAN SPEED can be set without DRY mode.

1 Press the FAN SPEED button.

Each time the button is pressed, the fan speed changes.

AUTO ULo Lo Me Hi

Operation capacity by your choice FAN SPEED

Set automatically by microcomputer AUTO
Silent operation ULo
Energy-saving operation Lo
Standard operation Me
Powerful operation with high capacity Hi

NOTE

• When FAN SPEED is changed from Hi to Lo or ULo, the sound of

refrigerant may be heard.

– 14 –

RLF012A201_EN_1-34.indd 14 10/28/2016 12:36:43 PM

 COOL/HEAT/DRY/FAN mode operation

1 Press the MODE button.

Set to a required mode.

(COOL), (HEAT), (DRY), (FAN)

2 Press the ON/OFF button.

3 Press the TEMP button.

Press or button for the preferred temperature.

Recommendation
COOL HEAT DRY FAN
26 °C - 28 °C 22 °C - 24 °C 24 °C - 26 °C —

Airflow direction adjustment procedure. Page 16

4 Press the FAN SPEED button
Set the fan speed as preferred.
A fan speed cannot be set under Dry operation.

NOTE

• In case air is not blown out, when starting the heating To stop: Press the ON/OFF button.
operation. Page 32

• The operation mode can also be set or changed when the

air-conditioner is not in operation.

Air-conditioner operation temperature range

■ Use within the following operational range. Operating outside of this range may result in the protection devices being activated,
preventing the unit from working.

COOL mode operation HEAT mode operation

Outside temperature Approximately -15 to 46 °C Approximately -20 to 24 °C

Inside temperature Approximately 18 to 32 °C Approximately 10 to 30 °C

Below approximately 80%

The long-term use of the unit with a humidity level
Inside humidity
exceeding 80% may result in condensation forming
on the surface of the indoor unit, leading to water
drops.

Characteristics of HEAT mode operation

Mechanism and capacity of HEAT mode operation
• The unit draws heat from the cold outside air, transfers it to indoors and heats the room. As a characteristic of heat pump system, the
heating capacity reduces when the outside air temperature gets colder.
• It may take some time to supply hot air after turning on the air-conditioner.
• If the outside temperature becomes extremely low, it would be better to use an additional source of heating.

Defrosting
If the outside temperature becomes low and humidity is high, the heat exchanger in the outdoor unit may frost over, which prevents efficient heating.
If this happens, the automatic defrost function is activated and the heating operation stops for 5 to 15 minutes during defrosting.
• Both indoor and outdoor fans stop and the RUN light blinks slowly (1.5 seconds ON, 0.5 seconds OFF) during defrosting.
• The outdoor unit may release some steam during defrosting. This is to help the defrosting process and is not a defect.
• The HEAT operation resumes as soon as defrosting has been completed.

– 15 –

RLF012A201_EN_1-34.indd 15 10/28/2016 12:36:43 PM

 Airflow direction adjustment
■ Up/down direction can be adjusted with the AIR FLOW U/D (UP/DOWN) button on the remote control. Every time you press this button,
the mode changes as follows:
Change on AIR FLOW (UP/DOWN) mode.

(Flap stopped) (Swing)

■ Left/right direction can be adjusted with the AIR FLOW L/R (LEFT/RIGHT) button on the remote control. Every time you press this
button, the mode changes as follows:
Change on AIR FLOW (LEFT/RIGHT) mode.
(Louver stopped)

NOTE (Swing)

• The actual position of the flap and louver may differ from the display shown.

NOTE FOR HEATING OPERATION

• When heating operation starts, the flap and louver direction is fixed at the horizontal / center position in order to avoid cold draft. It
returns to the set position when the warm air supply is started.
• The flap and louver direction will be controlled to the horizontal/center position when the room temperature reaches the set
temperature and compressor stops or when defrosting is in operation.
• The airflow direction cannot be set during the period mentioned above. Change the airflow direction settings after the warm air is
supplied and the flap/louver goes to the set position.

Memory flap (Flap or louver stopped)

When you press the AIR FLOW (U/D or L/R) button once while the flap or louver is operating, it stops swinging at the position.
Since this angle is memorized in the microcomputer, the flap or louver will automatically be set at this angle when the next
operation is started.
• Recommended angle of the flap when
WARNING stopping
• Do not expose directly to airflow from the air-conditioner for a long time.

HEAT (Slant forward

CAUTION blowing)
• When in COOL or DRY operation, do not operate for a long period with the
airflow blowing straight down. Otherwise, condensation may appear on the
outlet grill and drip down.
(Horizontal
• Do not try to adjust the flaps and louvers by hand, as the control angle may COOL, DRY
blowing)
change or the flap or louver may not be closed completely.

3D AUTO operation
■ Fan speed and airflow direction are automatically controlled, allowing the entire room to be efficiently air-conditioned.

1 Press the ON/OFF button.

2 Press the 3D AUTO button.

Each time the 3D AUTO button is pressed, the display is switched in the
order of:
No display
(3D AUTO) (Normal operation)

Releasing procedure
Press the 3D AUTO button to turn off the 3D AUTO display.

NOTE

• 3D AUTO operation is canceled when you switch the operation mode.

• If 3D AUTO operation is canceled then the airflow direction changes to that
used before 3D AUTO was set.
• 3D AUTO operation can be set in AUTO, COOL, or HEAT operation mode
only.

– 16 –

RLF012A201_EN_1-34.indd 16 10/28/2016 12:36:44 PM

 SLEEP TIMER operation
■ The unit will stop automatically after the set time lapses.
The set temperature is automatically adjusted according to the lapse time in order to avoid too much cooling or heating. Page 19

1 Press the SLEEP button.

■ If it is pressed while the unit is off

SLEEP TIMER operation starts with the previous operation settings, and the
air-conditioner is turned off after the set time lapses.

■ If it is pressed while the unit is running

The air-conditioner is turned off after the set time lapses.
Every time the button is pressed, the display changes as follows:

... (Units of one hour)

No display
(canceled)

Example: You prefer it to stop after 3 hours.

Set to

The timer light (yellow) is on.

Changing of set time • The unit stops after the set time lapses.
Set a new time by pressing SLEEP button.
NOTE
How to cancel
• SLEEP operation will not function during ALLERGEN CLEAR operation.
Press the CANCEL button to turn off the SLEEP
• SLEEP TIMER cannot be set simultaneously with OFF TIMER.
display.

OFF TIMER operation

(canceled)

■ The unit stops automatically when the set time comes.

With the air-conditioner turned off, start the operation from Step 1. With the air-conditioner running, start from Step 2.
Example: You prefer it to stop 22:30.

1 Press the ON/OFF button.

2 Press the OFF TIMER button.

OFF TIMER display is blinking.

3 Press the “ or
Every time the
0:00 0:10 0:20
(TIMER)” button.
button is pressed, the display is switched in the order of:
... 1:00 1:10 (Units of ten minutes)

Every time the button is pressed, the display is switched in the order of:
0:00 23:50 23:40 ... 23:00 22:50 (Units of ten minutes)

Set at 22:30.

4 Press the SET button.

The display changes from blinking to steady lighting and the setting is
complete.
The timer light (yellow) is on.

NOTE

Changing of set time • The unit stops at the end of the set period of time.
• Make sure to press the button within 60 seconds from the last operation
Set a new time by using the OFF TIMER button. in step 3, otherwise the setting is not completed.
• The current time is not displayed during OFF TIMER operation.
• OFF TIMER operation will not function during ALLERGEN CLEAR
How to cancel operation.
Press the CANCEL button to turn off the timer • Different from SLEEP TIMER operation, automatic set temperature
display. adjustment is not done during OFF TIMER operation.

– 17 –

RLF012A201_EN_1-34.indd 17 10/28/2016 12:36:45 PM

 ON TIMER operation
■ Operation starts 5 to 60 minutes before the set time so that the room temperature reaches the optimum temperature at the set time. Page 19
ON TIMER operation can be set regardless of whether the air-conditioner is running or not.
Example: When the preferred room temperature is required at 8:00.

1 Press the ON TIMER button.

ON TIMER display is blinking.

2 Press the “ or
Every time the
0:00 0:10 0:20
(TIMER)” button.
button is pressed, the display is switched in the order of:
... 1:00 1:10 (Units of ten minutes)

Every time the button is pressed, the display is switched in the order of:
0:00 23:50 23:40 ... 23:00 22:50 (Units of ten minutes)

Set at 8:00.

3 Press the SET button.

The display changes from blinking to steady lighting and the setting is
complete.
The timer light (yellow) is on.
If ON TIMER setting is performed when air-conditioner is running,
air-conditioner operation will stop.

NOTE

• Operation starts 5 to 60 minutes before the set time.

Changing of set time • The timer light (yellow) goes out at the set time.
Set a new time by using the ON TIMER button. • Make sure to press the button within 60 seconds from the last operation
in step 2, otherwise the setting is not completed.
• The current time is not displayed during ON TIMER operation.
How to cancel • ON TIMER operation will not function during ALLERGEN CLEAR
operation.
Press the CANCEL button to turn off the timer • If the ON/OFF button is pressed after setting the ON TIMER, the setting
display. will be canceled.

SLEEP TIMER + ON TIMER operation

■ This is the combined timer operation of SLEEP TIMER and ON TIMER.
Example: When it is required to stop after 3 hours and then start operation at 8:00, near the
set temperature.

1 SLEEP TIMER setting

Set by the procedures on page 17.

Set to

2 ON TIMER operation setting

Set by the above procedure mentioned in ON TIMER.
Set to

The setting of the lighting of the timer light (yellow) of this unit is complete.

• After the SLEEP TIMER set time has lapsed, the operation stops, and it starts from
5 to 60 minutes before the ON TIMER’s set time.
• The timer light is turned off when ON TIMER set time comes.

Changing of set time How to cancel

Set a new time by using the SLEEP or ON TIMER Press the CANCEL button to turn off the timer display.
button.

– 18 –

RLF012A201_EN_1-34.indd 18 10/28/2016 12:36:46 PM

 ON TIMER + OFF TIMER operation
■ This is the combined timer operation of ON TIMER and OFF TIMER.
Example: Present time is 21:00. The air-conditioner running.
When it is preferred to stop at 22:30, and then start operation at 8:00, near the set
temperature.

1 OFF TIMER operation setting

Set by the procedures on page 17. Set to

2 ON TIMER operation setting

Set by the procedures on page 18. Set to

Timer light (yellow) on the unit will light when the setting is completed.

■ The set time will be displayed on the remote control. The display will change
depending on the operational status.

• The air-conditioner stopping.

First the air-conditioner starts running with ON TIMER.
After the air-conditioner stops running with OFF TIMER.
• The air-conditioner running.
First the air-conditioner stops running with OFF TIMER.
After the air-conditioner starts running with ON TIMER.

Changing of set time

Set a new time by using the OFF TIMER or ON TIMER button.

NOTE How to cancel

• Timer operation can be set only for next 24 hours. Press the CANCEL or ON/OFF button to turn off the timer display.

Comfort Start-up SLEEP TIMER

In ON TIMER operation, the unit starts the operation a little earlier, so When SLEEP TIMER is selected, the set temperature is automatically
that the room can approach optimum temperature at ON time. This is adjusted after a while, ensuring that the room is not too cold during
called “Comfort start-up”. cooling or too warm during heating.
• Mechanism
The room temperature is
▼

In COOL operation
▼

▼
COOL operation HEAT operation
checked 60 minutes before
(Stop) Operation starts
the ON time. Depending on
the temperature at that time, Set temperature
the operation starts 5 to 60 (Operation) +1.0°C -1.0 °C
minutes before the timer is at -2.0 °C
Set temperature Set temperature -3.0 °C
ON.
• The function is available -1.0°C
for both COOL and HEAT -6.0 °C
operation mode (including Check the room Set time Set time 1 hour 2 hour Set time 30 minutes 1 hour 2 hour
AUTO). It does not work for temp. 1 hour before.
DRY mode.

ALLERGEN CLEAR operation

■ The power of enzymes is used to eliminate allergy-causing allergens that
accumulate on the allergen clear filter.

1 Press the ALLERGEN CLEAR button.

Press the ON/OFF or

To stop:
ALLERGEN CLEAR button.

NOTE

• Since the room temperature may change quite a bit, it is recommended

that this be used when no one is in the room. (It completes automatically
in approximately 90 minutes.)
• During ALLERGEN CLEAR operation temperature, fan speed, airflow
direction and timer operations settings cannot be made.
• In case of SCM multi system, ALLERGEN CLEAR control function is
invalid.
• In case of SCM multi system, if ALLERGEN button is pressed by
mistake, the indoor unit which received such command will stop.

– 19 –

RLF012A201_EN_1-34.indd 19 10/28/2016 12:36:46 PM

 WEEKLY TIMER operation
■ Up to 4 programs with timer operation (ON TIMER / OFF TIMER) are available for each day of the week. Maximum 28 programs per week
are available. Once this has been set, the timer operation will be repeated at the same programs every week unless the WEEKLY TIMER
is canceled.
: WEEKLY TIMER setting
Sample (At cooling season)
: MANUAL setting

WEEKLY TIMER ON/OFF setting

■ Switch the WEEKLY TIMER to ON/OFF by using the WEEKLY button.

1 Press the WEEKLY button.

The WEEKLY TIMER becomes effective.

Every time the WEEKLY button is pressed, the display is switched in the
order of:
No display
(WEEKLY TIMER on) (WEEKLY TIMER off)

When the WEEKLY TIMER is set to ON, the timer light (yellow) of the
air-conditioner is on.
When the battery of the remote control is replaced or the ACL switch is
pressed, the remote control is set to the initial state. Since the WEEKLY
TIMER program is not set in the initial state, set the program according to the
setting procedure.

NOTE

• The WEEKLY TIMER is switched to ON/OFF regardless of • OFF TIMER operation of the WEEKLY TIMER is effective only
whether the air-conditioner is running or not. when the air-conditioner is running. When the time set by the
• The ON TIMER operation of the WEEKLY TIMER is effective OFF TIMER is reached, the air-conditioner stops.
regardless of whether the air-conditioner is running or not. • When multiple program numbers are set for the current day
When the ON TIMER setting time is reached, the remote (day of the week), the operation is performed from the earliest
control operates according to the contents that are set. The time that is set.
remote control display is also switched to the operation • When various timers (ON TIMER, OFF TIMER, and SLEEP
contents that are set. The setting can be changed from the TIMER) are operating, the WEEKLY TIMER does not operate
remote control after ON TIMER operation of the WEEKLY even if the time set in the ON TIMER or OFF TIMER is
TIMER. reached. The WEEKLY TIMER becomes effective after various
The following contents can be set by the ON TIMER. timers are terminated.
Operation mode, fan speed, temperature, airflow direction, • The ON TIMER or OFF TIMER of the same time in the same
ECO, 3D AUTO, NIGHT SETBACK, SILENT day of the week cannot be set.
Comfort start-up is not performed for WEEKLY TIMER • In case WEEKLY TIMER setting is not sent to the unit, TIMER
ON TIMER operation. light will not turn on even if the WEEKLY button is pressed and
is displayed on the remote control.

– 20 –

RLF012A201_EN_1-34.indd 20 10/28/2016 12:36:47 PM

 Setting mode <Individual setting>

Set after setting the current day of the week and the time.

1 Press the PROGRAM

and current day of the week blink.
button.

2 Press the “ or (TIMER)” button.

Select a day of the week to be reserved.

Every time the button is pressed, the display is switched in
the order of:

Mon Tue Wed ... Sun Display of all of the days of

the week

Every time the button is pressed, the display is switched in

the order of:
Mon Display of all of the days of Sun Sat ... Tue
the week

3 Press the SET button.

The day of the week is determined and the program number
blinks.

4 Press the “ or

Select a program number.

(TIMER)” button.

Every time the button is pressed, the display is switched in the

order of:
P1 P2 P3 P4

Every time the button is pressed, the display is switched in the

order of:
P1 P4 P3 P2

5 Press the SET button.

When no set contents (ON TIMER or OFF TIMER) are
available, both the and timers blink.

When set contents (ON TIMER or OFF TIMER) are

available, either or timer blinks.

6 Press the ON TIMER or OFF TIMER button.

ON TIMER or OFF TIMER is determined and time display blinks.

ON TIMER is selected OFF TIMER is selected

– 21 –

RLF012A201_EN_1-34.indd 21 10/28/2016 12:36:48 PM

 7 Press the “ or

Set a time.
(TIMER)” button.

Every time the button is pressed, the display is switched in the

order of:
0:00 0:10 0:20 ... 1:00 1:10 (Units of ten minutes)

Every time the button is pressed, the display is switched in the

order of:
0:00 23:50 23:40 ... 23:00 22:50 (Units of ten minutes)

When ON TIMER is selected, go to Step 8.

When OFF TIMER is selected, go to Step 9.

8 Set required operation contents.

When ON TIMER is selected, operation mode, fan speed, and airflow direction can be
changed and the ECO, SILENT or NIGHT SETBACK operation can be set.

9 Press the SET button.

The time is determined and and blink.

10 Press the PROGRAM button or SET button.

When the PROGRAM button is pressed, the setting is sent to the air-conditioner.
Since it takes 3 seconds for transmission, point the remote control at the remote control
signal receiver of the indoor unit during the period.
When the setting is received, a buzzer sound (pip, pip, pip) is emitted.
When the SET button is pressed, the setting continues from Step 2.

Setting mode <Collective setting>

■ Set the same operation contents to the same program number of all the days of the week. In Step 2 above, select “all of the days of the
week”. When the contents that were individually set exist in the same program number, the contents are overwritten.

NOTE

• If no operation is performed for 60 seconds in setting mode, the setting changes that have been made until then become invalid and
the setting mode terminates. Subsequently, and all the program numbers (P1, P2, P3 and P4) blink for 10 seconds.
(This blinking can not be observed if setting mode gets terminated while setting only one program.)

• At the end of the setting mode, point the remote control at the air-conditioner and press the PROGRAM button. In this case, check
that the air-conditioner emits a reception buzzer sound three times (pip, pip, pip). If the buzzer sound is not emitted, set the mode
to the setting mode again by pressing the PROGRAM button and check that the buzzer sound is emitted.

– 22 –

RLF012A201_EN_1-34.indd 22 10/28/2016 12:36:50 PM

 How to cancel the setting <Individual setting>

1 Press the PROGRAM

and current day of the week blink.
button.

2 Press the “ or (TIMER)” button.

Select a day of the week to be canceled.

3 Press the SET button.

The day of the week is determined and the program number blinks.

4 Press the “ or (TIMER)” button.

Select a program number to be canceled.
At cancelation operation, do not press the SET button. If the SET button is
pressed, the mode is shifted to the Set mode.

5 Press the CANCEL button.

The setting contents of the ON or OFF TIMER are canceled and
displayed on the time display section.
is

6 Press the PROGRAM button.

When the PROGRAM button is pressed, the setting is sent to the
air-conditioner.
When the setting is received, a buzzer sound (pip, pip, pip) is emitted.
The setting contents of each program are canceled. Perform the operation
indicated above for each program to be canceled.

How to cancel the setting <Collective setting>

■ When the same operation contents exist in the same program number of all the days of the week, collective erase is allowed. In Step 2
above, select “all of the days of the week”. The procedure from Step 3 is the same as that indicated above.
If the operation contents have been changed or erased by individual setting after the collective setting described in page 22, causing
setting content discrepancies among the days of the week, collective erase is not allowed.

The WEEKLY TIMER setting contents can be confirmed.

Confirm mode

1 Press the PROGRAM button for 3 seconds or more.

blinks and the setting content lights.

2 Press the “ or (TIMER)” button.

Select a day of the week and a program number to be confirmed.
Display starts from the current day of the week. For the program without
setting, is displayed. When the PROGRAM button is pressed in
Confirm mode, a setting mode is set.
Mon P1 P2 P3 P4

Tue P1 P2 P3 P4

Sun P1 P2 P3 P4

Display of all of the

days of the week P1 P2 P3 P4

Releasing procedure
The Confirm mode can be terminated by pressing the ON/OFF, CANCEL or
SET button.

NOTE

• If no operation is performed for 60 seconds in Confirm mode, the Confirm

mode is terminated.
– 23 –

RLF012A201_EN_1-34.indd 23 10/28/2016 12:36:50 PM

 HIGH POWER/ECO operation
1 Press the ON/OFF button.

2 Press the HI/ECO button.

• When the operating mode is AUTO, COOL or HEAT
Every time the HI/ECO button is pressed, the display is switched in the
order of:
No display

(HIGH POWER) (ECO) (Normal operation)

• When the operating mode is DRY or ON TIMER + OFF TIMER

Every time the HI/ECO button is pressed, the display is switched in the
order of:

No display

(ECO) (Normal operation)

HIGH POWER operation

Pressing the HI/ECO button intensifies the operating power and initiates powerful cooling or heating operation for 15 minutes
continuously. The remote control displays and the FAN SPEED display disappears.

NOTE

• During the HIGH POWER operation, the room temperature • When the following operations are set, HIGH POWER
is not controlled. When it causes an excessive cooling or operation will be canceled.
heating, press the HI/ECO button again to cancel the HIGH 1 When the HI/ECO button is pressed again.
POWER operation. (The operation mode will be changed to the ECO operation)
• HIGH POWER operation is not available during the DRY and 2 When the operation mode is changed.
ON TIMER + OFF TIMER operations. 3 When it has been 15 minutes since HIGH POWER
• When HIGH POWER operation is set after setting operation has started.
ON TIMER operation, HIGH POWER operation will start from 4 When the 3D AUTO button is pressed.
the set time. 5 When the SILENT button is pressed.
6 When the NIGHT SETBACK button is pressed.
• After HIGH POWER operation, the sound of refrigerant
flowing may be heard. • Not operable while the air-conditioner is OFF.

ECO operation
Pressing the HI/ECO button initiates a soft operation with the power suppressed in order to avoid an excessive cooling or heating.
The remote control displays.
The set temperature will be adjusted according to the amount of movement made by the person(s) the motion sensor has detected.
MODE:AUTO mode operation
Heat Source & Movement Low Normal High None When the extent of human
+3ºC Low
COOL/DRY +2ºC
movement is low
When the extent of human
Set High
temperature movement is high
When there is no one in the
HEAT None
room
-2ºC
-3ºC • The set temperature is automatically
MODE:COOL/HEAT/DRY mode operation adjusted during ECO operation,
however, the indication on the remote
Heat Source & Movement Low Normal High None
control display does not change.
+3ºC
• When the SLEEP TIMER, OFF TIMER,
COOL/DRY
and ON TIMER + OFF TIMER operation
Set are set, the motion sensor does not
temperature adjust temperatures.
HEAT

-3ºC

NOTE

• It will go into ECO operation at the next time the air-conditioner • When the following operations are set, ECO operation will be
runs in the following case. canceled.
1 When the air-conditioner is stopped by ON/OFF button 1 When the HI/ECO button is pressed again.
during ECO operation. 2 When the operation mode is changed from DRY to
2 When the air-conditioner is stopped in SLEEP or OFF FAN.
TIMER operation during ECO operation. 3 When the NIGHT SETBACK button is pressed.
3 When the operation is retrieved from SELF CLEAN • Not operable while the air-conditioner is OFF.
or ALLERGEN CLEAR operation.
– 24 –

RLF012A201_EN_1-34.indd 24 10/28/2016 12:36:51 PM

 NIGHT SETBACK operation
■ During the cold season, the room temperature can be maintained at a comfortable level during the absence, at night, and while the room
is unattended. The air-conditioner maintains the constant temperature at about 10°C.

1 Press the NIGHT SETBACK button.

Every time the NIGHT SETBACK button is pressed, the display is switched
in the order of:

No display
(NIGHT SETBACK on) (NIGHT SETBACK off)

Releasing procedure
Press the NIGHT SETBACK button or MODE button to turn off the NIGHT
SETBACK display.

NOTE

• During NIGHT SETBACK operation, the air-conditioner maintains the set

temperature at about 10°C.
• During NIGHT SETBACK operation, temperature settings cannot be
made.
• Since the room temperature may change quite a bit, it is recommended
that this be used when no one is in the room.
• During NIGHT SETBACK operation, HIGH POWER and ECO operations
cannot be set.
• When NIGHT SETBACK operation is canceled by pressing the NIGHT
SETBACK button, the operation mode is reset to the mode immediately
prior to the NIGHT SETBACK operation.

SILENT operation
■ When the SILENT operation is set, the unit operates more silently reducing noise from the outdoor unit.
With the air-conditioner turned off, start the operation from Step 1. With the air-conditioner running, start from Step 2.

1 Press the ON/OFF button.

2 Press the SILENT button.

• When the operating mode is AUTO, COOL, HEAT or NIGHT SETBACK

Every time the SILENT button is pressed, the display is switched in the
order of:

No display
(SILENT on) (SILENT off)

Releasing procedure
Press the SILENT button to turn off the SILENT display.

NOTE

• During SILENT operation, the maximum cooling and heating capacities

deteriorate.
• SILENT operation will not function during DRY and FAN operation.
• In case of following operations, the air-conditioner will resume SILENT
operation whenever it turns ON again.
1 When the air-conditioner is stopped by ON/OFF button during SILENT
operation.
2 When the air-conditioner is stopped in SLEEP or OFF TIMER
operation during SILENT operation.
3 When the operation is retrieved from SELF CLEAN or ALLERGEN
CLEAR operation.
• Not operable while the air-conditioner is OFF.
• The noise level of the outdoor unit may not decrease depending on the
condition.
• In case of SCM multi system, SILENT control is invalid.

– 25 –

RLF012A201_EN_1-34.indd 25 10/28/2016 12:36:52 PM

 MENU function
■ MENU function is used for setting the display brightness adjustment, AUTO OFF operation, SELF CLEAN operation and PRESET opera-
tion.

1 Every time the MENU switch is pressed with the tip of

a ballpoint pen, etc., the display is switched in order of:

Display brightness AUTO OFF

adjustment operation

PRESET operation SELF CLEAN

operation

Display brightness adjustment

■ This function can be used when it is necessary to adjust the brightness of unit display.

1 Select the display brightness adjustment by pressing

the MENU switch.

2 Select the brightness level by pressing “ or

button.
(TIMER)”

100% 50% 0%
(Orignal) (Turned off)

3 Press the SET button.

– 26 –

RLF012A201_EN_1-34.indd 26 10/28/2016 12:36:52 PM

 AUTO OFF operation
■ In order to prevent the air-conditioner from continuing to operate although the person(s) has already left the room, the air-conditioner automatically stops
approximately 1 hour (or 2 hours) after the sensor judges that there is no one in the room.

1 Select the AUTO OFF operation by pressing the MENU

switch.

2 Select AUTO OFF level by pressing “

button.
or (TIMER)”

( AUTO OFF
off ) ( AUTO OFF
on ) ( AUTO OFF
on )

3 Press the SET button.

Settings of AUTO OFF

Stop the operation 1 hour after the sensor judges that there is no one
1H*
in the room.

Stop the operation 2 hours after the sensor judges that there is no
2H
one in the room.

* Default setting

Releasing procedure

In step 2, select AUTO OFF off, and press the SET button. Check that the
AUTO OFF indicator has turned off.

NOTE

• Emits a warning sound, “peep, peep, peep”, and stops the operation
automatically when there is no one in the room for setting time (Standby)
When the motion sensor detects a person 12 hours after the operation
was stopped, the operation resumes with the same settings.
The operation does not resume even if a person is detected after 12
hours has elapsed. (The RUN light blinks slowly during standby.)
• It is recommended that you set the AUTO OFF function to “Off”, if people
who carry out minimal movements, such as an infant or sick person, are
in the room.
(The motion sensor may determine that there is no one in the room, and
stop operation.)
• When the SLEEP TIMER, OFF TIMER and ON TIMER + OFF TIMER
operation are set, the AUTO OFF functions is disabled.
• The AUTO OFF function does not activate if the operation is started by
the ON TIMER when there is no one at home.
• When 12 hours has elapsed after the operation was stopped by the
AUTO OFF function, the operation does not resume even when a person
walks into the room. However, the remote control display indicates
operation.

– 27 –

RLF012A201_EN_1-34.indd 27 10/28/2016 12:36:53 PM

 SELF CLEAN operation
■ SELF CLEAN operation should be run after AUTO, COOL and DRY operation to remove the moisture from inside of the indoor unit and
control the growth of mold and bacteria.

1 Select the SELF CLEAN operation by pressing the

MENU switch.

2 Select SELF CLEAN on by pressing “ or

button.
(TIMER)”

(SELF CLEAN off) (SELF CLEAN on)

3 Press the SET button.

NOTE

• Two hours later, the air-conditioner stops SELF CLEAN operation

automatically. To stop the air-conditioner immediately, press the ON/OFF
button.
• SELF CLEAN operation is not operated after HEAT, FAN, OFF TIMER,
SLEEP and ALLERGEN CLEAR operations have finished.
• The indoor unit fan runs for about two hours in SELF CLEAN operation.
• The RUN light illuminates during SELF CLEAN operation.
3 seconds
ON

OFF
1 second

• Pressing the SLEEP button, ALLERGEN CLEAR button or NIGHT

SETBACK button during SELF CLEAN operation cancels the SELF
CLEAN operation and then the unit is set to SLEEP, ALLERGEN CLEAR
or NIGHT SETBACK operation.
• This is not a function for removing mold, germs or grime that have
already adhered to the unit.

PRESET operation
■ This operation can save the preferred setting for future operation.

1 Select the PRESET operation by pressing the MENU

switch.

2 Select preferred OPERATION MODE, TEMPERATURE,

FAN SPEED and AIR FLOW direction.

3 Press the SET button.

4 When air -conditioner is operating AUTO, COOL, HEAT,

DRY, FAN and NIGHT SETBACK, press MODE button 3
seconds or more. PRESET operation will start.

NOTE

• When pressing MODE button for PRESET operation during the 3D

AUTO or HIGH POWER operation, it will be canceled.
• When pressing MODE button for PRESET operation during the
ECO operation, it will continue.

– 28 –

RLF012A201_EN_1-34.indd 28 10/28/2016 12:36:54 PM

 Maintenance
Before maintenance During the operational season

Turn off the power source. Cleaning the air filter Standard interval is once
every two week
• Do not spill any liquid to the
unit.
• Do not touch the aluminum fins
1 Remove the air filter • Pull up the air inlet panel forward.
• Lightly hold the knobs both sides and lift a little
to remove the panel forward.
on the heat exchanger.
• Stand firmly on a stepladder
or other stable object when re-
moving the air inlet panel and
filter. 2 Cleaning If the filter is very dirty, clean it with warm water
(approx. 30°C), and dry it thoroughly.
CAUTION
Do not use the following items: • Do not clean the filters with boiling water.
• Hot water (40°C or more) • Do not dry them over an open flame.
It may deform or discolour the unit. • Pull them out gently.
• Petrol, paint thinner, benzine or
cleanser, etc. I t m ay d e fo r m o r
scratch the unit. 3 Reinstall the air filter

• Hold firmly the filter at both sides as shown at right and

insert securely.
• Operating without the air filters will make the unit dusty,
and may cause damage.

Cleaning the unit Cleaning the air inlet panel

• Wipe the unit with a soft, dry cloth, or use a vacuum • Removal, installation of air inlet panel.
cleaner. • Wipe the panel with a soft, dry cloth.
• If the unit is very dirty, wipe it with a cloth soaked in
warm water. CAUTION
• Do not wash the air inlet panel with water.

How to open and close the air inlet panel

Open Close
Place fingers at the corners on both sides of the panel and pull Push both corners of the panel evenly and press further lightly
up the panel forward so that it will be open by about 60 degrees. at the center.

How to remove and install the air inlet panel

1. Basic structure A: Outer panel of air

: Hook inlet panel NOTE

• Air inlet panel’s open/close of this unit is driven by electrical

B: Inner panel motor.
of air inlet panel • Improper handling by hand will cause mechanical damage
and effect to open/close operation.
Main body • Do not close air inlet panel forcibly. Outer panel is to be
closed automatically when power source is ON.

2. How to remove the air inlet panel Hold both panels

(1) Open

Hold the lower corners of A, then release the Lift up A together with B by holding both of
hook from the main body part. them.

(2) Remove (3) Install

Insert the panel arm into the slot on the front panel from the
position shown on the left, hold the panel at both ends of lower
part, lower it downward slowly, then push it slightly until the
latch works.

Approx. 80°

Lift up A about 80 degrees.

Hold both panels and extract them in front.
– 29 –

RLF012A201_EN_1-34.indd 29 10/28/2016 12:36:54 PM

 NOTE Cooling/heating is affected by an air filter clogged up with dust etc., and the operation noise becomes louder. It
may also use extra electricity. Please clean the air filter at appropriate intervals.

At the end of the season At the beginning of the season

1 Perform the fan operation for 2 to 3 hours.

Dry the inside of the unit.
1 Ensure that the earth wiring is not snapped nor
disconnected.

2 Make sure that there is no corrosion or rust on

the base frame of the outdoor unit.
2 Stop the unit and turn off the power source.
The unit consumes approx. 4W even when the unit is not operating.
Turning off the power source will help saving energy consumption and cost. 3 Make sure that there are no obstacles blocking
the airflow around the air intake and outlet
openings of the indoor and outdoor units.
3 Clean and reinstall the air filters.

4 Clean both the indoor and outdoor units. 4 Turn on the power source.

5 Remove batteries from the remote control. 5 Insert batteries in the remote control.

Installing, inspecting and replacing the air-cleaning filter

1. Open the air inlet panel and remove the air filters. Page 29

2. Remove the allergen clear filter (Light orange) from air-conditioner and inspect the
filter. Use a vacuum cleaner to remove any dust or dirt from the allergen clear filter.
Replace the allergen clear filter if it cannot be cleaned or if it has been for about
1 year.
(The allergen clear filter should be replaced after about 1 year of used. However, the
actual replacement period may vary depending on the conditions in which the filter
is used.)

Remove the photocatalytic washable deodorizing filter (orange) from air-conditioner

and inspect the filter. Periodically, remove any dust or dirt from the photocatalytic Panel
washable deodorizing filter. If the photocatalytic washable deodorizing filter is (air-conditioner)
particularly dirty, it may be washed with water. However, the filter is fragile, so do
not scrub it with excessive force. After washing the filter, place it in sunlight to dry.
Placing the filter in sunlight restores the deodorizing effect.

3. Install the air-cleaning filter in the air-conditioner.

NOTE
Air-cleaning filter
• The allergen clear filter and the photocatalytic washable deodorizing filter
may be installed on either the right or left side of the air-conditioner.
• Install the allergen clear filter with the light orange side on front side.

4. Install the air filters and close the air inlet panel. Page 29

CAUTION
• The heat exchanger may injure your fingers.
• Stand firmly on a stepladder or other stable object when removing the air inlet panel and filters.

For replacing the air-cleaning filter, contact your dealer.

Item Feature Color
The power of enzyme is used to eliminate allergy- Light orange
Allergen clear filter
causing allergens that accumulate on the filter.
Photocatalytic washable Sources of odors on the filter are broken up, resulting in Orange
deodorizing filter a deodorizing effect.

– 30 –

RLF012A201_EN_1-34.indd 30 10/28/2016 12:36:56 PM

 Proper installation
Suitable installation position
• Do not put any obstruction in front of the indoor unit, preventing proper ventilation and functioning.
• Do not install the unit in any of the following places:
− Where there is a danger of leaking flammable gases.
− Where there is substantial splashing of oil.
• Malfunctioning due to corrosion may occur if the unit is installed in a spa where sulfide gases are generated, or in a seaside resort
exposed to sea breezes. Contact your dealer.
• The air-conditioner and remote control must be at least 1 meter away from a TV set or radio.
• Drain the dehumidified liquid from the indoor unit into a spot that drains well.

Pay attention to operating noises

• When you install the unit, take care to choose a place that can comfortably stand the weight of the unit and does not increase the
operating noise or vibration. If vibration is transmitted through the house, fix the unit with the aid of vibration-proof pads between the
unit and the fittings.
• Select a place where cold or hot air, operation noises from the indoor and outdoor units do not cause any inconvenience to your
neighbours.
• Do not leave any obstacles near the outlet and inlet of the outdoor unit. This may cause malfunctioning and increased operating noise.
• If you hear an irregular noise during operation, contact your dealer.

Inspection and maintenance

Depending on operating environment, the inside of the air-conditioner may become dirty after a few year operations. This will reduce
performance. In addition to normal cleaning, we would recommend inspection and maintenance. (This may lead the air-conditioner to
having a longer life without any trouble.)
• Contact your dealer, or any distributor, for inspection and maintenance. (There will be a charge for this service).
• We would recommend inspection and maintenance to be carried out during the off-season.
• If the supply cord of this appliance is damaged, it must only be replaced by a repair shop appointed by the manufacturer, because
special purpose tools are required.

Troubleshooting
Please carry out the following checks before making a service call.
If the air-conditioner does not
The air-conditioner does not work at all. operate properly after you have
• Has the power switch been turned off? checked the left points, or if any
• Has the timer been set in the “ON” position? doubt still exists after you have
• Is there a power failure or a blown fuse? consulted page 32, or if things
Poor cooling or heating happen as shown on page 33,
• Have you set the thermostat at a suitable temperature? switch off the power and contact
• Is the air filter clean? (Not clogged?) your dealer.
• Have you left any doors or windows open?
• Is there any direct sunlight entering the room?
• Is there a heat source in the room?
• Are there too many people in the room?

– 31 –

RLF012A201_EN_1-34.indd 31 10/28/2016 12:36:57 PM

 Notice
Airflow

Air is not blown out when starting the HEATING operation. Airflow has stopped to prevent blowing out of cold air until the
RUN light blinks slowly indoor heat exchanger has warmed up. (2 to 5 minutes)
(1.5 seconds ON, 0.5 seconds OFF)

Air is not blown out for 5 to 15 minutes or cool air is When outdoor temperature is low and humidity is high, the
blown out for a moment at HEATING operation. unit sometimes performs defrosting automatically. Please
RUN light blinks slowly wait. During defrosting, water or steam may release from the
(1.5 seconds ON, 0.5 seconds OFF) outdoor unit.

Air is not blown out when starting the DRY operation. The indoor fan may stop to prevent re-evaporation of
dehumidified moisture and to save energy.
(RUN light is on)

Noise
You hear a slight gurgling sound. This is caused by refrigerant moving within the unit.

You hear a slight cracking sound. This is caused by heat expansion or contraction.

You hear a hissing or clicking sound. This is caused by the operation of the refrigerant control
valves or electric components.

Whistling noise is heard from the outdoor unit. This means that the rotation speed of the compressor is
increasing or decreasing.

Sometimes a “Shooooo” sound might come for a short This is the sound when operation of another indoor unit is
time from the unit that is turned off. stopped.

Others

The unit does not restart immediately after you have Restart is blocked for 3 minutes after you have stopped the
stopped it. operation to protect the unit.
(RUN light is on)
The 3 minutes protection timer in the microcomputer
automatically starts it up again.

Some steam releases during COOL operation. This may occur if the room’s temperature and humidity are
very high. It disappears as soon as the temperature and
humidity decrease.

There is a slight smell. Air blown out during operation may smell. This is caused by
tobacco or cosmetics adhering to the unit.

After a power cut, the unit does not restart even if power If the auto restart function is not set, the unit will not restart
has been restored. automatically. Use the remote control to start the operation
again.

Remote control signals are not received. Remote control signals may not be received if the signal
receiver on the air-conditioner is exposed to direct sunlight or
other bright light.
If so, block the sunlight or reduce the other light.

Moisture may form on the air outlet grills. If the unit is operated for a long time in high humidity, moisture
may form on the air outlet grills and start dripping.

Fan will not stop immediately after unit operation is Indoor fan : Fan will not stop after 2 hours if set to SELF
stopped. CLEAN operation.
Outdoor fan : Fan will not stop about a 1 minute period in
order to protect the unit.

RUN light stays on even though operation was stopped. The RUN light illuminates during SELF CLEAN operation.
Run light will turn off when SELF CLEAN operation ends.

– 32 –

RLF012A201_EN_1-34.indd 32 10/28/2016 12:36:57 PM

 Contact your dealer
■ Turn off the power switch immediately and inform your dealer in any of the following situations:

• The fuse or switch blows continuously.

• The cable becomes extremely hot.
The covering of the cable is cracked.
• The TV, radio or other equipment starts to malfunction.
• A switch does not activate properly.
• A strange noise is heard during operation.
• When abnormalities occur, turn off the power source immediately and turn it on after 3 minutes. Restart the operation with ON/OFF
button of the remote control and the abnormalities still continue.
• The RUN and TIMER lights on the unit display section blink quickly (0.5 seconds ON; 0.5 seconds OFF) or the lights do not work.

Auto restart function

■ Auto restart function records the operational status of the air-conditioner immediately prior to be switched off by a power cut, and then
automatically resumes operations after the power has been restored.
■ The following settings will be canceled:
1 Timer settings
2 HIGH POWER operations

NOTE

• Auto restart function is set at on when the air-conditioner is shipped from the factory. Consult with your dealer if this function needs
to be switched off.
• When power failure occurs, the timer setting is canceled. Once power is resumed, set the timer again.

About the multiple air-conditioners

Simultaneous Operation
• The air-conditioners cannot be in different operating modes at the same time, such as one unit being in the “Cool” mode and one
unit being in the “Heat” mode.
• When conducting different operations, the air-conditioner that was operated first will be given priority, so the air-conditioner that is
operated after that will conduct air blowing operation.
• When you want to give priority to the air-conditioner that was started later, either stop the air-conditioner that has priority or change
the operation type of the unit operated first to match that of the unit operated second.
• When other indoor units are operating in different modes, the RUN light illuminates.
0.5 seconds
ON

OFF
0.5 seconds

Automatic Operation
• When the remote control operation switch is in the AUTO mode, the air-conditioner automatically selects either COOL or HEAT
mode when operation is started depending on the room temperature.
• During simultaneous operation of air-conditioners, operation modes may be automatically changed in response to the temperatures
of the individual rooms; this will result in the operation of the outdoor unit being stopped. In such a case, COOL or HEAT mode should
be used instead of AUTO mode. (This is only relevant when more than one air-conditioner unit is being used.)

Refrigerant (oil) recovery operation

• If the all of the indoor units are not operated at the same time for an extended period, the cooling or heating performance may
temporarily decrease. This is in order to control the recovery of the refrigerant (oil) in the stopped indoor unit(s). At this time, the
sound of refrigerant flowing may be heard from the stopped indoor unit(s).

– 33 –

RLF012A201_EN_1-34.indd 33 10/28/2016 12:36:57 PM

 Self diagnosis function
■ We are constantly trying to do better service to our customers by installing such judges that show abnormality of each function as follows

RUN light
Description of trouble Cause

Indoor heat exchanger sensor 1 • Broken heat exchanger sensor 1 wire, poor connector
1-time flash
error connection

2-time flash Room temperature sensor error • Broken room temperature sensor wire, poor connector
connection

Indoor heat exchanger sensor 3 • Broken heat exchanger sensor 3 wire, poor connector
3-time flash
error connection
TIMER light ON
5-time flash Circuit error • Circuit failure or poor connector connection

6-time flash Indoor fan motor error • Defective fan motor, poor connector connection

7-time flash Refrigerant is insufficient • Refrigerant is insufficient, leaking

Closed service valve • Closed service valve

TIMER light

1-time flash Outdoor temperature sensor error • Broken outdoor sensor wire, poor connector connection

Outdoor heat exchanger sensor • Broken heat exchanger sensor wire, poor connector
2-time flash error connection
RUN light keeps flashing
4-time flash Discharge pipe sensor error • Broken discharge pipe sensor wire, poor connector connection

5-time flash Suction pipe sensor error • Broken suction pipe sensor wire, poor connector connection

Current cut • Compressor locking, open phase on compressor output,

1-time flash short circuit on power transistor, closed service valve

Trouble of outdoor unit • Broken compressor wire

2-time flash
• Compressor blockage

3-time flash Over current • Overload operation, overcharge of refrigerant

4-time flash Power transistor error • Broken power transistor

RUN light ON
• Gas shortage, defective discharge pipe sensor,
5-time flash Over heat of compressor closed service valve

• Defective power source, broken signal wire, defective

6-time flash Error of signal transmission
indoor/outdoor unit boards

7-time flash Outdoor fan motor error • Defective fan motor, poor connector connection

Keep flashing Cooling high pressure protection • Overcharge of refrigerant, short circuit of outdoor unit

• Defective compressor
RUN light 2-time flash 2-time flash Rotor lock • Open phase on compressor
• Defective outdoor unit boards

RUN light 7-time flash 1-time flash Closed service valve • Closed service valve

RUN light OFF Keep flashing Indoor air inlet panel open • Indoor air inlet panel open

– 34 –

RLF012A201_EN_1-34.indd 34 10/28/2016 12:36:57 PM

 ORIGINAL INSTRUCTIONS

USER’S MANUAL
AIR-CONDITIONER USER’S MANUAL ENGLISH
AIR-CONDITIONER

MANUEL DE L’UTILISATEUR FRANÇAIS

CLIMATISEUR

ANWENDERHANDBUCH DEUTSCH
KLIMAGERÄT

SRK20ZSX-S
ISTRUZIONI PER L’USO ITALIANO
CONDIZIONATORE D’ARIA
SRK25ZSX-S
SRK35ZSX-S
SRK50ZSX-S MANUAL DEL PROPIETARIO ESPAÑOL
SRK60ZSX-S ACONDICIONADOR DE AIRE

GEBRUIKERSHANDLEIDING NEDERLANDS
AIRCONDITIONING

MANUAL DO UTILIZADOR PORTUGUÊS

APARELHO DE AR CONDICIONADO

ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ ΕΛΛΗΝΙΚΑ

ΚΛΙΜΑΤΙΣΤΙΚΟ

РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ РУССКИЙ

КОНДИЦИОНЕР ВОЗДУХА

KULLANIM KILAVUZU TÜRKÇE

MITSUBISHI HEAVY INDUSTRIES THERMAL SYSTEMS, LTD.

16-5 Konan 2-chome, Minato-ku, Tokyo, 108-8215, Japan
http://www.mhi-mth.co.jp/en/

MITSUBISHI HEAVY INDUSTRIES AIR-CONDITIONING EUROPE, LTD.

7 Roundwood Avenue, Stockley Park, Uxbridge, Middlesex, UB11 1AX, United Kingdom
Tel : +44-20-7025-2750
Fax: +44-20-7025-2751
http://www.mhiae.com/

MITSUBISHI HEAVY INDUSTRIES AIR-CONDITIONERS AUSTRALIA, PTY. LTD.

9C Commercial Road Kingsgrove NSW 2208 PO BOX 318 Kingsgrove NSW 1480
Tel : +61-2-8571-7977
Fax: +61-2-8571-7992
https://www.mhiaa.com.au/

RLF012A201
201610

RLF012A201_Cover.indd 1 10/28/2016 2:54:35 PM