Model: DI2,4,5 DS4 (Over than ROM

Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

1.5.1 Generals
In case Job-sites where established N-plex ROM was applied that need to change to new DSK program or Operation control program
that is over than Ver4.00 is applied, there are some SPEC to be modified or set. This manual will help you how to work In detail..

1.5.2 SPEC of Control Part in CP(address$0000 ~ $3FFF)

1) Modify/SET SPEC : The SPEC must be set.
Address LABEL name SIZE Basic Contents
000D No_Of_Side 1 01 Number of Installed Hall Button Asy
(1 hall rise: 0x01, 2 hall rise: 0x02, Combined to Group Control: 0x01)
000E Separate_Fan_Light 1 FF To apply by separation Car Light, Car Fan and Stack Fan each other
0279 Full_Load_Min_Level_Dist[] 1 64 Compensation of leveling error gap in LOW_ZONE UP short operation with 80% load
027A 1 64 Compensation of leveling error gap in LOW_ZONE Down short operation with 80% load
027B 1 64 Compensation of leveling error gap in MIDDLE_ZONE UP short operation with 80% load
027C 1 64 Compensation of leveling error gap in MIDDLE_ZONE Down short operation with 80% load
027D 1 64 Compensation of leveling error gap in HIGH_ZONE UP short operation with 80% load
027E 1 64 Compensation of leveling error gap in HIGH_ZONE Down short operation with 80% load
027F Full_Load_Max_Level_Dist[] 1 64 Compensation of leveling error gap in LOW_ZONE UP long operation with 80% load
0280 1 64 Compensation of leveling error gap in LOW_ZONE Down long operation with 80% load
0281 1 64 Compensation of leveling error gap in MIDDLE_ZONE UP long operation with 80% load
0282 1 64 Compensation of leveling error gap in MIDDLE_ZONE Down long operation with 80% load
0283 1 64 Compensation of leveling error gap in HIGH_ZONE UP long operation with 80% load
0284 1 64 Compensation of leveling error gap in HIGH_ZONE Down long operation with 80% load
Above standard data of address $0279 ~ $0284 are all 0x64, and they were set from manufacturer. They can be changeable to adopt to jobsite
condition as refer to [Appendix1]
23F0 Timer[R7CF_OFF_TIMER] 1 94 Timer SPEC to control car fan, timer is 3minutes.
23F1 1 11

27
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

23F4 Timer[R7SF_OFF_TIMER] 1 94 Timer SPEC to control stack fan, timer is 3minutes.
23F5 1 11
23F8 Timer[R7LF_OFF_TIMER] 1 C8 Timer SPEC to control car light, timer is 30minutes.
23F9 1 AF
2695 Acd[0x0C].Operation 1 A4 Permit SPEC to maintain car lighting under standby operation mode(ACD0x0C) with door
open after rescue operation
In case of 0xA4 : Maintains car lighting under 0x0C mode
In case of 0xA0 : Car light off after door’s open under 0x0C mode
2) Check SPEC : The SPEC must be checked.
Address LABEL name SIZE Basic Contents
0476 Door_Close_Delay 1 E8 Timer SPEC for door close auto announcement. 1 unit is 1msec.
0477 1 03 (Hex value 0x3E8 is 1000 by decimal and 1 second.)
0C60 ~ Hall_Up_Call 8 Bit for floor where hall up call is possible can be set ‘1’.
0C67 0C60:1st ~8th floor 0C61:9th ~16th floor 0C62:17th ~24th floor 0C63:25th ~32nd floor
0C64:33rd ~40th floor 0C65:41st ~48th floor 0C66:49th ~56th floor 0C67:57th ~64th floor
0C80 ~ Hall_Down_Call 8 Bit for floor where hall down call is possible can be set ‘1’.
0C87 0C80:1st ~8th floor 0C81:9th ~16th floor 0C82:17th ~24th floor 0C83:25th ~32nd floor
0C84:33rd ~40th floor 0C85:41st ~48th floor 0C86:49th ~56th floor 0C87:57th ~64th floor
In case a couple of lift is operated by duplex system but service floors are different with above SPEC, one lift that serve lowest floor can have 1st floor. And
This is a reference to set SPEC. (For example, in case lift 1 serves B2 to 8 and Lift2 serves 1 to 8 with duplex system , the lowest floor is B2 and this is 1st
floors, SPEC setting is as following. [ Lift 1 SPEC : 0C60:FF, 0C61:01, 0C80:FE, 0C81:03 Lift 2 SPEC : 0C61:FC, 0C61:01, 0C80:F8, 0C81:03 ]
015B Force_Door_Close_Cut 1 FF When SES, PSES, OPEN B/T activated, it permits door time SPEC.
In case of 0xFF : When above switches activated, Door reopens and closes after door
time passes.
In case of 0x00 : When above switches activated, Door will close as soon as open

28
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

1.5.3 Management part SPEC (Address$4000 ~ $7FFD)

* Caution: SPEC which are relevant to service floor must consider and set as ‘0x00’ about non-service floor until 64th floor. And
ensure that address to be set ‘0x00’ is correct.
1) Prior work item
Record the origin data of below address.
Address LABEL name SIZE Basic Contents
4010 Ref_Floor 1 Reference floor
7406 Disp_Floor 1 Dispersion floor

2) Common SPEC ( All customers have same data)

Address LABEL name SIZE Basic Contents
4005 Non_Stop1_Trigger_Cond 1 FF Non-Stop 1 supplied or not (FF/00)
4006 Non_Stop2_Trigger_Cond 1 FF Non-Stop 2 Supplied or not (FF/00)
4300 1 32 The first waiting time value setting when it counts stand-by time.
Ref_Fl_Wait_Car
4301 1 00 (Stand-by lift at reference floor)
4302 1 32 The first waiting time value setting when it counts stand-by time
Non_Dir_Car
4303 1 00 (Lift that has non direction
4304 1 03 The first waiting time value setting when it counts stand-by time
Closed_Car
4305 1 00 (Lift that closed doors)
4306 1 02 The first waiting time value setting when it counts stand-by time
Ready_To_Run_Car
4307 1 00 (Lift that closing doors current)
4308 1 00 The first waiting time value setting when it counts stand-by time
Run_Car
4309 1 00 (Lift that is traveling)
430A 1 00 The first waiting time value setting when it counts stand-by time
Stop_Delay
430B 1 00 (Lift that is decelerating for service)

29
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

4400 Operation 1 00
4401 Ref_Fl 1 00 Permit code for duplex operation (Non management mode)
4402 Dis_Fl 1 00
4410 Operation 1 00
4411 Ref_Fl 1 59 Permit code for duplex operation (ATT mode)
4412 Dis_Fl 1 00
4420 Operation 1 21
4421 Ref_Fl 1 00 Permit code for duplex operation (VIP stand-by mode)
4422 Dis_Fl 1 00
4430 Operation 1 01
4431 Ref_Fl 1 00 Permit code for duplex operation (VIP operation mode)
4432 Dis_Fl 1 00
4440 Operation 1 10
4441 Ref_Fl 1 55 Permit code for duplex operation (Going office mode)– Non used
4442 Dis_Fl 1 00
4450 Operation 1 80
4451 Ref_Fl 1 41 Permit code for duplex operation (Single operation mode)
4452 Dis_Fl 1 00
4460 Operation 1 90
4461 Ref_Fl 1 40 Permit code for duplex operation (Duplex mode)
4462 Dis_Fl 1 42

30
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

4740 1 82
4741 1 02
Jam_Detect_Count Hall button jam detection time(About 3minutes)
4742 1 00
4743 1 00
4D00 SPD_Nplex_Timer[0] 1 32 Assistance operation from long distance detection timer (50 seconds)
4D01 SPD_Nplex_Timer[1] 1 1E Start of dispersion (dispersion floor) delay timer (30 seconds)
4D02 SPD_Nplex_Timer[2] 1 02 Start of dispersion (reference floor) delay timer (2 seconds)
4D03 SPD_Nplex_Timer[3] 1 00 Non Used

31
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

3) Job site SPEC (If there is no basic value, that is for job site SPEC and it reflects job site condition/environments)
Address LABEL name SIZE Basic Contents
If Rom version of DHL is over than V2.00, set ‘0xFF’ at address’ 0x013B’, if not set’ 0x00’.
Set ‘0xAA’(basic value) at below address 0x4050 ~ 0x4057, and set ’0x55’(basic value) at address 0x4060 ~ 0x4067
Non-Stop 1 service pattern (8th ~ 1st floor)
b7 b6 b5 b4 b3 b2 b1 b0
4050 Non_Stop_1[0] 1 8 FL 7 FL 6 FL 5 FL 4 FL 3 FL 2 FL 1 FL

Non-Stop 1 service pattern (16th ~ 9th floor)

b7 b6 b5 b4 b3 b2 b1 b0
4051 Non_Stop_1[1] 1 16 FL 15 FL 14 FL 13 FL 12 FL 11 FL 10 FL 9 FL

Non-Stop 1 service pattern (24th ~ 17th floor)

b7 b6 b5 b4 b3 b2 b1 b0
4052 Non_Stop_1[2] 1 24 FL 23 FL 22 FL 21 FL 20 FL 19 FL 18 FL 17 FL

Non-Stop 1 service pattern (32nd ~ 25th floor)

b7 b6 b5 b4 b3 b2 b1 b0
4053 Non_Stop_1[3] 1 32 FL 31 FL 30 FL 29 FL 28 FL 27 FL 26 FL 25 FL

Non-Stop 1 service pattern (40th ~ 33rd floor)

b7 b6 b5 b4 b3 b2 b1 b0
4054 Non_Stop_1[4] 1 40 FL 39 FL 38 FL 37 FL 36 FL 35 FL 34 FL 33 FL

Non-Stop 1 service pattern (48th ~ 41st)

b7 b6 b5 b4 b3 b2 b1 b0
4055 Non_Stop_1[5] 1 48 FL 47 FL 46 FL 45 FL 44 FL 43 FL 42 FL 41 FL

32
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

th th
Non-Stop 1 service pattern (56 ~ 49 floor)
b7 b6 b5 b4 b3 b2 b1 b0
4056 Non_Stop_1[6] 1 56 FL 55 FL 54 FL 53 FL 52 FL 51 FL 50 FL 49 FL

Non-Stop 1 service pattern (64th ~ 57th)

b7 b6 b5 b4 b3 b2 b1 b0
4057 Non_Stop_1[7] 1 64 FL 63 FL 62 FL 61 FL 60 FL 59 FL 58 FL 57 FL

Non-Stop 2 service pattern (16th ~ 9th floor)

b7 b6 b5 b4 b3 b2 b1 b0
4060 Non_Stop_2[0] 1 16 FL 15 FL 14 FL 13 FL 12 FL 11 FL 10 FL 9 FL

Non-Stop 2 service pattern (24th ~ 17th floor)

b7 b6 b5 b4 b3 b2 b1 b0
4061 Non_Stop_2[1] 1 24 FL 23 FL 22 FL 21 FL 20 FL 19 FL 18 FL 17 FL

Non-Stop 2 service pattern (32nd ~ 25th floor)

b7 b6 b5 b4 b3 b2 b1 b0
4062 Non_Stop_2[2] 1 32 FL 31 FL 30 FL 29 FL 28 FL 27 FL 26 FL 25 FL

Non-Stop 2 service pattern (40th ~ 33rd floor)

b7 b6 b5 b4 b3 b2 b1 b0
4063 Non_Stop_2[3] 1 40 FL 39 FL 38 FL 37 FL 36 FL 35 FL 34 FL 33 FL

33
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

th rd
Non-Stop 2 service pattern (40 ~ 33 floor)
b7 b6 b5 b4 b3 b2 b1 b0
4064 Non_Stop_2[4] 1 40 FL 39 FL 38 FL 37 FL 36 FL 35 FL 34 FL 33 FL

Non-Stop 2 service pattern (48th ~ 41st)

b7 b6 b5 b4 b3 b2 b1 b0
4065 Non_Stop_2[5] 1 48 FL 47 FL 46 FL 45 FL 44 FL 43 FL 42 FL 41 FL

Non-Stop 2 service pattern (56th ~ 49th floor)

b7 b6 b5 b4 b3 b2 b1 b0
4066 Non_Stop_2[6] 1 56 FL 55 FL 54 FL 53 FL 52 FL 51 FL 50 FL 49 FL

Non-Stop 2 service pattern (64th ~ 57th)

b7 b6 b5 b4 b3 b2 b1 b0
4067 Non_Stop_2[7] 1 64 FL 63 FL 62 FL 61 FL 60 FL 59 FL 58 FL 57 FL

34
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

1. In case of simplex(single) operation : Set 0x00 at address ‘ 0x4070 ~ 0x408F;
2. In case of duplex operation: ① Copy all hall up service data of Lift 2’s address’ 0x0C60~0x0C67’ to lift 1’s address ‘0x4070 ~0x4077’
and copy all hall up service data of Lift 1’s address’ 0x0C60~0x0C67’ to lift 2’s address ‘0x4070 ~0x4077’
② Copy all hall down service data of Lift 2’s address’ 0x0C80~0x0C87’ to lift 1’s address ‘0x4080 ~0x4087’
and copy all hall down service data of Lift 1’s address’ 0x0C80~0x0C87’ to lift 2’s address ‘0x4080 ~0x4087’.
※ Refer to appendix 2 to check SPEC in case Lift 1 and lift2 ‘s service floor data is different.
Hall Up Call Svc. Spec. of partner lift
Address Floor Basic
0x4070 1st ~ 8th 0x00
0x4071 9th ~ 16th 0x00
0x4072 17th ~ 24th 0x00
4070~4077 Other_Hall_Up_Call[0] ~ [7] 8 0x4073 25th ~ 32nd 0x00
0x4074 33rd ~ 40th 0x00
0x4075 41st ~ 48th 0x00
0x4076 49th ~ 56th 0x00
0x4077 57th ~ 64th 0x00

Hall Down Call Svc. Spec. of partner lift.

Address Floor Basic
0x4080 1st ~ 8th 0x00
0x4081 9th ~ 16th 0x00
0x4082 17th ~ 24th 0x00
4080~4087 Other_Hall_Down_Call[0] ~ [7] 8 0x4083 25th ~ 32nd 0x00
0x4084 33rd ~ 40th 0x00
0x4085 41st ~ 48th 0x00
0x4086 49th ~ 56th 0x00
0x4087 57th ~ 64th 0x00

35
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

1. Check if call class of DHL PCB was set normal or not before setting of below SPEC.
① In case DHL-250 PCB or high grade PCB was supplied to site, set as below method. But in case of DHL-240 PCB or low grade PCB, refer to installation manual.
4 3 2 1
ON
OFF Å DIP SW – (DHL-250 ~ DHL-270 B/D 의 “SW1”)

| | | |______ON : Through Type , OFF : Normal

| | |_____________ ON : N Type – Hall B/T connected to HDC,HUC, OFF : M Type – Hall B/T connected to HDC,HUC

| |____________________ ON : L Type – Hall B/T connected to HD,HU, OFF : K Type – Hall B/T connected to HD, HU.

|__________________________________ Terminal resistor

② Setting standard of call class in Hall line (K class, L class, M class, N class)
No. Single line Twin line Call Type of single line Call Type of twin line
1 Normal * K *
2 Disable * M *
3 Normal Normal K L
4 Normal Disable K M
5 Disable Normal M K
6 Disable Disable M L

2. Below Address’ 0x4090 ~ 0x4094’ are common SPEC what applied to all job site and should be set by basic value..

4090 Hall_Mode[0](User definition1) 1 FF Trigger : Applicable service map Use(FF)/ No use(00)

A Type service map
4091 Hall_Mode[0](User definition1) 1 83
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_1

B Type service map

4092 Hall_Mode[0](User definition1) 1 00
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_1

C Type service map

4093 Hall_Mode[0](User definition1) 1 00
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_

D Type service map

4094 Hall_Mode[0](User definition1) 1 00
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_

36
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

1. In case VIP button applied to hall :
① To serve for VIP call by lift 2 ② To serve for VIP call by lift 2
Address Data Address Data
4095 FF 4095 FF
4096 00 4096 00
4097 00 4097 00
4098 00 4098 00
4099 11 4099 12

2. In case VIP button does not applied to hall :

Address Data
4095 FF
4096 00
4097 00
4098 00
4099 00

4095 Hall_Mode[1] (VIP mode) 1 FF Trigger : : Applicable service map Use(FF)/ No use(00)
A Type service map
4096 Hall_Mode[1] (VIP mode) 1 00
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_1

B Type service map

4097 Hall_Mode[1] (VIP mode) 1 00
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_1

C Type service map

4098 Hall_Mode[1] (VIP mode) 1 00
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_

D Type service map

4099 Hall_Mode[1] (VIP mode) 1
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_

37
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

Below Address’ 0x409A ~ 0x409E’ are common SPEC what applied to all job site and should be set by basic value

409A Hall_Mode[2](User definition 2) 1 FF Trigger : : Applicable service map Use(FF)/ No use(00)

A Type service map
409B Hall_Mode[2](User definition 2) 1 83
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_1

B Type service map

409C Hall_Mode[2](User definition 2) 1 00
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_1

C Type service map

409D Hall_Mode[2](User definition 2) 1 00
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_

D Type service map

409E Hall_Mode[2](User definition 2) 1 00
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_

38
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

① Normal(K, single line) ② Disable(M, single line) ③ Normal(K,L, twin Hall line)
Address Data Address Data Address Data
409F FF 409F FF 409F FF
40A0 83 40A0 00 40A0 C3
40A1 00 40A1 00 40A1 00
40A2 00 40A2 23 40A2 00
40A3 00 40A3 00 40A3 00
④ Disable(M,L, twin Hall line) ⑤ Lift 1,2 Normal(K ), ⑥ Lift 1,2 Normal(K),
Lift 2 is Disable line(M, twin Hall line) Lift 1 is Disable type(M, twin Hall lime)
Address 데이터 Address Data Address Data
409F FF 409F FF 409F FF
40A0 00 40A0 83 40A0 83
40A1 00 40A1 00 40A1 00
40A2 63 40A2 22 40A2 21
40A3 00 40A3 00 40A3 00

409F Hall_Mode[3] (Normal mode) 1 FF Trigger : : Applicable service map Use(FF)/ No use(00)
A Type service map
40A0 Hall_Mode[3] (Normal mode) 1
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_1

B Type service map

40A1 Hall_Mode[3] (Normal mode) 1
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_1

C Type service map

40A2 Hall_Mode[3] (Normal mode) 1
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_

D Type service map

40A3 Hall_Mode[3] (Normal mode) 1
Definition of service map bit:[b7]:K [b6]:L [b5]:M [b4]:N [b3]:HOLD [b2]:NULL [b1]:EL_2 [b0]:EL_

39
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

1. In case of single hall line :
1) Check if address ‘0x000D’ has ‘ 0x01’. (If not, reset data to ‘0x01’) ※ In case of group management panel, address ‘0x000D’ ‘s data is ‘0x01’
2) Set the data for hall call Type at address ‘0x40A4’ as refer to below variable bit structure.
Example) Normal hall call (K) : 0x01 , Normal hall call(L): 0x02 , Disable(M): 0x04

2. In case of twin hall line :

1) Check if address ‘0x000D’ has ‘0x02’. (If not, reset data to ‘0x02’) ※ In case of group management panel, address ‘0x000D’ ‘s data is ‘0x01’
2) The first hall line : Set the data for hall call Type at address ‘0x40A4’ as refer to below variable bit structure .
Example) Normal hall call (K): 0x01 , Normal hall call(L): 0x02 , Disable(M): 0x04
3) The second hall line : Set the data for hall call Type at address ‘0x40A5’ as refer to below variable bit structure .
Example) Normal hall call (K): 0x01 , Normal hall call(L): 0x02 , Disable(M): 0x04

Address Variable data name Bit structure meaning

b7 b6 b5 b4 b3 b2 b1 b0
0x40A4 Hall_Side_Svc_Type[0] 1st hall line call Type
X X X X N M L K
b7 b6 b5 b4 b3 b2 b1 b0
0x40A5 Hall_Side_Svc_Type[1] 2nd hall line call Type
X X X X N M L K

40A4 Hall_Side_Svc_Type[0] 1 Hall call Type setting for 1ST hall line node check
40A5 Hall_Side_Svc_Type[1] 1 Hall call Type setting for 2nd hall line node check

40
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

1. Set the below address ‘0x4500 ~ 0x4502’ as basic value ’ 0x01’.
2.In case VIP call is applied to building, set to address ‘0x4503’ as basic value’ 0x03’.
3 In case VIP call is not applied to building, set to address ‘0x4503’ as basic value’ 0x00’.
Hall_Svc_Option_Spec[0]
4500 1 01 [b7]X [b6]X [b5]X [b4]X [b3]X [b2]X [b1]X [b0] Service Permit SET
(Normal call)
Hall_Svc_Option_Spec[1]
4501 1 01 [b7]X [b6]X [b5]X [b4]X [b3]X [b2]X [b1]X [b0]Service permit SET
(B Side call)
Hall_Svc_Option_Spec[2]
4502 1 01 [b7]X [b6]X [b5]X [b4]X [b3]X [b2]X [b1]X [b0]Service permit SET
(Disable call)
[b0] Service permit
[b1] Car call cancellation is available if registered
[b2] ‘0’ (Releases VIP mode when lift is decelerating under last call)
Hall_Svc_Option_Spec[3] ‘1’ (Releases VIP mode when door close completed after last car call servce)
4503 1 00/03
(VIP call) [b3]X [b4]X [b5]X [b6]X [b7]X

(X : Not Used)

41
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

Set all to address ‘0x4700 to 0x4708’ as data ’0x00’ because most of job sites do rarely park by hall button
Floor bit setting for Parking Hall Button
Address Floor Basic value
0x4700 1st ~ 8th 0x00
0x4701 9th ~ 16th 0x00
0x4702 17th ~ 24th 0x00
Floor data of parking hall
4700~4707 8 00 0x4703 25th ~ 32nd 0x00
button 0x4704 33rd ~ 40th 0x00
0x4705 41st ~ 48th 0x00
0x4706 49th ~ 56th 0x00
0x4707 57th 64th 0x00

Data Call Type

00 K
4708 Type of parking hall button 1 00 01 L
02 M
03 N

42
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

1. In case VIP button applied to hall, set to applicable floor bit of below address’ 0x4710 ~ 0x4717’,
In case VIP button is nothing, surely set all to below address ‘0x4710 ~ 0x4717’ as data ‘0x00’.
2. In case VIP button applied to hall, set to address ‘0x4718’ as data ‘0x03’
In case VIP button is nothing, set to address ‘0x4718’ as data ’0x00’.
Floor bit setting for VIP hall call button (basic data: 0x00 at all floor)
Address floor Basic value
0x4710 1st ~ 8th 0x00
0x4711 9th ~ 16th 0x00
0x4712 17th ~ 24th 0x00
4710~4717 VIP hall button floor 8 0x4713 25th ~ 32nd 0x00
0x4714 33rd ~ 40th 0x00
0x4715 41st ~ 48th 0x00
0x4716 49th ~ 56th 0x00
0x4717 57th 64th 0x00

In case VIP button applied to hall, set to address ‘0x4718’ as data ‘0x03’
4718 VIP hall button type 1 00/03
In case VIP button is nothing, set to address ‘0x4718’ as data ’0x00’.

43
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

1. In case of normal call, set to applicable floor bit of below address ’0x4720 ~ 0x4727’,
In case of normal call button is nothing, surely set all to below address ‘0x4720 ~ 0x4727’ as data ‘0x00’
2. Surely set all to below address ‘0x4728 ~ 0x472F’ as data ‘0x00’.
3. In case of wheelchair button is applied, set to applicable floor bit of below address ’0x4730 ~ 0x4737’,
In case wheelchair button is not applied, set to address ‘0x4730 ~ 0x4737’ as data ‘0x00’.
4. In case VIP button is applied, set to applicable floor bit of below address’0x4738 ~ 0x473F’,
In case VIP button is not applied, set to address ‘0x4738 ~ 0x473F’ as data’0x00’.
Set to bit as ‘1’ where A type hall button installed
Address Floor Basic Value
0x4720 1st ~ 8th
0x4721 9th ~ 16th
0x4722 17th ~ 24th
A type (Normal) Hall button
4720~4727 8 0x4723 25th ~ 32nd
installed floor SPEC 0x4724 33rd ~ 40th
0x4725 41st ~ 48th
0x4726 49th ~ 56th
0x4727 57th 64th

Set to bit as ‘1’ where B type hall button installed

Address Floor Basic Value
0x4728 1st ~ 8th
0x4729 9th ~ 16th
0x472A 17th ~ 24th
B type (through) Hall button
4728~472F 8 0x472B 25th ~ 32nd
installed floor SPEC 0x472C 33rd ~ 40th
0x472D 41st ~ 48th
0x472E 49th ~ 56th
0x472F 57th 64th

44
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

Set to bit as ‘1’ where C type hall button installed
Address Floor Basic Value
0x4730 1st ~ 8th
0x4731 9th ~ 16th
0x4732 17th ~ 24th
C type (Disable) Hall button
4730~4737 8 0x4733 25th ~ 32nd
installed floor SPEC 0x4734 33rd ~ 40th
0x4735 41st ~ 48th
0x4736 49th ~ 56th
0x4737 57th 64th

Set to bit as ‘1’ where D type hall button installed

Address Floor Basic Value
0x4738 1st ~ 8th
0x4739 9th ~ 16th
0x473A 17th ~ 24th
D type(VIP) Hall button
4738~473F 8 0x473B 25th ~ 32nd
installed floor SPEC 0x473C 33rd ~ 40th
0x473D 41st ~ 48th
0x473E 49th ~ 56th
0x473F 57th 64th

45
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

In case VIP-1, VIP-2, VIP-3 switches are applied to job site or CRT supervisory panel is applied and VIP-1, VIP-2, VIP-3 command are exist in customer, set
the address ‘0x4744 ~ 0x4749’ according to Job site condition.
But In case VIP-1, VIP-2, VIP-3 switches are applied or CRT SVP panel is applied and VIP-1, VIP-2, VIP-3 command is not exist,
Set data all ’0x00’ to below address ’0x4744 ~ 0x4749’.
Ex1) To perform down direction VIP call at 10th floor when VIP-1 switch is ‘On’ or VIP-1 command occurs in CRT SVP Panel
Set data ‘0x0A’ to address ‘0x4744’ and set data’0x48’ to address ‘0x4745’
Ex2) To perform up direction VIP call at 1st floor when VIP-2 switch is ‘On’ or VIP-2 command occurs in CRT SVP Panel
Set data ‘0x01’ to address ‘0x4746’ and set data’0x88’ to address ‘0x4747’
Ex3) To perform down direction VIP call at 7th floor when VIP-3 switch is ‘On’ or VIP-3 command occurs in CRT SVP Panel
Set data ‘0x07’ to address ‘0x4748’ and set data’0x48’ to address ‘0x4749’

4744 VIP_Call_Switch[0][0] 1 VIP-1 floor data (0x01 <1st floor> ~ 0x40 <64th floor>)
VIP-1 call class and direction (Default : 0x00) – Call Type is always ‘N .
b7 b6 b5 b4 b3 b2 b1 b0
4745 VIP_Call_Switch[0][1] 1 UP DOWN X X N M L K

4746 VIP_Call_Switch[1][0] 1 VIP-2 floor data (0x01 <1st floor> ~ 0x40 <64th floor>)
VIP-2 call class and direction (Default : 0x00) – Call Type is always ‘N .
b7 b6 b5 b4 b3 b2 b1 b0
4747 VIP_Call_Switch[1][1] 1 UP DOWN X X N M L K

4748 VIP_Call_Switch[2][0] 1 VIP-3 floor data (0x01 <1st floor> ~ 0x40 <64th floor>)
VIP-3 call class and direction (Default : 0x00) – Call Type is always ‘N .
b7 b6 b5 b4 b3 b2 b1 b0
4749 VIP_Call_Switch[2][1] 1 UP DOWN X X N M L K

46
 Model: DI2,4,5 DS4 (Over than ROM
Optional SPEC2 DATA Edition for New DSK application Version. 4.00)

Address LABEL name SIZE Basic Contents

1.Single (Simplex) operation: The reference floor data of address ‘4010’ which was recorded under prior work process shall be copy to address ‘0x4A00’
and set the dispersion data ’0x00’ to address’0x4A02’.

2. Duplex Operation:: The reference floor data of address ‘4010’ which was recorded under prior work process shall be copy to address ‘0x4A00’ and The
dispersion floor data of address’0x07406’ ’ which was recorded under prior work process shall be copy to address ‘0x4A02’.
4A00 SPD_Reference1 1 Reference floor (If data is ‘0x00’, never return to reference floor) – The first floor is
considered to Lowest floor
4A02 SPD_Dispersion1 1 Dispersion floor (If data is ‘0x00’, never disperses) - The first floor is considered to
Lowest floor
Set ‘0x00’ to below address ‘0x4A03’.
4A03 Non used 1 00

47