Scribd
Upload
2K views12 pages

LPOW Thermometer Manual

This forehead thermometer can be customized according to different user needs. It allows adjusting the temperature unit (Celsius or Fahrenheit), fever alert threshold, sound settings, and overall temperature offset. Long pressing the MODE button enters the setting mode where each parameter can be modified by pressing MODE, MEMO and SET buttons. The adjustable temperature offset range is -5°C to +5°C to account for environmental or individual factors. Exiting setting mode turns off the display.

Uploaded by

Shark Laser
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views12 pages

LPOW Thermometer Manual

This forehead thermometer can be customized according to different user needs. It allows adjusting the temperature unit (Celsius or Fahrenheit), fever alert threshold, sound settings, and overall temperature offset. Long pressing the MODE button enters the setting mode where each parameter can be modified by pressing MODE, MEMO and SET buttons. The adjustable temperature offset range is -5°C to +5°C to account for environmental or individual factors. Exiting setting mode turns off the display.

Uploaded by

Shark Laser
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

This product can be set according to the subjects of different colors and different

environments data to meet the different characteristics of populations or individuals.


- 3- TROUBLESHOOTING
Long press the MODE button to modify the measurement parameters.
MESSAGE SITUATION SOLUTION

1) Unit Set-Fl
Under the boot mode .Long press SET button to enter Fl, press the "MODE" or "MEMO" Temperature taken in not within Typical Make sure the forehead thermometer is for
button to switch Celsius and Fahrenheit temperature units, press the SET button to human temperature range forehead measurement, not other human
°
{34.0"C- 42.9 °C or 93.2 F- 109.2'F). body site.
confirm the unit settings (factory default is Fahrenheit).
Lo
2) Fever alert set-F2 Measured over the distance 1-5 cm(0.4-2 in). Optimum me�surement distance is 1cm.
Under Fl state, press SET button to enter the F2, press the "'MODE" button to Incorrect test position. See figure 2 Measuring position and distance.
decrease 0.1 "C, press the "MEMO" button plus 0.1 "C, long press to accelerate the Subject:; forehead hair, Antipyretic stickers, Subjects sit quietly 5-10 minutes before the

La
speed of temperature regulation, and finally press the SET button to save. (The factory headwithsweat,etc.
default is 38.1 'C)
Some people's body temperature is lower The main concern fever temperature
than the general population
3) Prompt sound settings-F3
F4 overall temperature offset is set incorrectly Adjust the temperature offset value
Under F2 state , short press SET button to enter F3, press MODE button or MEMO
button to set voice switch, and press the SET button to confirm the settings. (The Operating temperature exceeds the range of Move to a room within the operating range
factory default is the voice Prompt to open).
frr specified temperature. wait 30 minutes before taking temperature.

4) Overall temperature offset value---F4


The screen flicker, automatic turn off. Replace battery or the product has been
To meet the different colors, different characteristics of the population, or the damaged, needs repairs.
environment caused by seasonal temperature change is large that need for
temperature detection and debugging. Battery capacity is too low. Taking Install a new battery
Temperature is not allowed.
Under F3 state , short press the SET button to enter F4, press the MEMO button to

PDS
plus 0.1 'C, press the MODE button decrease 0.1 "C, long press fast subtraction

■
temperature, and then SET button to confirm the parameter setting. Ambient temperature changes too fast Wait until the ambient temperature
is stable.
Parameter adjustment range: -5"C and +5"C (factory default is 0).

...
(l)Poweris off. (l)Press On/Scam button again.
5) Exit setting mode (2) Improper battery installation. (2)Check the battery polarity.
(3)The battery is exhausted. (3)Replace with a new battery.
In the F4 mode, press the SET button will automatically turn off the screen, exit (4)0isplay remains blank. (4)Contactthe retailer or service center.
setting.

You might also like