INSTALLATION MANUAL

< Optional Software >

FRONTIER SERIES
DI PRINT/DATA WRITING
SERVICE SOFTWARE Ver.5.5

DI Print/Data Writing Service Software Ver.5.5

(FRONTIER 330/340 System Disk Ver.2.0 or later)
(FRONTIER 355/375 System Disk Ver.1.5 or later)
(FRONTIER 350/370/390 System Disk Ver.6.6 or later) Second Edition
PP3-A1001E2
INTRODUCTION

INTRODUCTION

• This installation manual explains the procedures for installing and setting up the DI Print and
Data Writing Service for Fujifilm Digital Minilab FRONTIER Series as well as precautions for its
use.

• This manual should be kept in a fixed place near the machine so that it can be referred to at any
time a point needs to be clarified.

Specifications are subject to change without notification.

Zip™ is a trademark of Iomega Corporation.

SmartMedia™ is a trademark of Toshiba Corporation.
CompactFlash™ is a trademark of SanDisk Corporation.
Microdrive™ is a trademark of IBM Corporation.
Memory Stick™ and Memory Stick Duo™ are trademarks of Sony Corporation.
SD Memory Card™ is a trademark of Toshiba Corporation, Matsushita Electric Industrial Co., Ltd and SanDisk Copo-
ration.
miniSD Memory Card™ is a trademark of SD Card Association.
Microsoft®, Windows® and Windows® 2000 are registered trademarks of Microsoft Corporation.
All other brand names or trademarks are the property of their respective owners.
CONTENTS

1 Precautions for Installation .............................................................................................. 5

1.1 Version of System/Option Software Combination .............................................................. 5

2 Hardware/System Configuration .................................................................................... 6

2.1 Hardware Configuration...................................................................................................... 6
2.1.1 FRONTIER 355/375 System .................................................................................. 6
2.1.2 FRONTIER 330/340 System .................................................................................. 7
2.1.3 FRONTIER 350/370/390 System ........................................................................... 8
2.1.4 Imaging Controller System (Example).................................................................... 9
2.2 System Preparations .......................................................................................................... 10
2.2.1 PC and Media Drive Preparations.......................................................................... 10
2.2.2 Hard Disk Partition ................................................................................................. 11
2.2.3 Virtual Memory Setting ........................................................................................... 11
2.2.4 Computer Name Setting......................................................................................... 13
2.2.5 Network Protocol Setting........................................................................................ 15
2.2.6 Creating a User Account ........................................................................................ 17
2.2.7 Restarting ............................................................................................................... 20

3 Installation ............................................................................................................................... 22
3.1 Standard Setup/Upgrade.................................................................................................... 23
3.2 Custom Setup/Upgrade ...................................................................................................... 25
3.2.1 Custom Setup/Upgrade for Use of DI Print/Data Writing Service [C4/C5] ............. 25
3.2.2 Custom Setup/Upgrade for Use of DI Print Service [C4] Only ............................... 27
3.3 MSDE/64MB SmartMedia Driver Installation...................................................................... 30
3.3.1 MSDE Installation................................................................................................... 30
3.3.2 64MB SmartMedia Driver Installation..................................................................... 31
3.4 Backup Order Function....................................................................................................... 32
3.4.1 Added Functions .................................................................................................... 32
3.4.2 Installation .............................................................................................................. 33
3.5 Installation to FRONTIER ................................................................................................... 35
3.5.1 [C4/C5] Installation ................................................................................................. 35
3.5.2 Installation Information Setup................................................................................. 36
3.5.3 Print Size Setup...................................................................................................... 38

4 Setting the Imaging Controller ........................................................................................ 39

4.1 Print Service Administration ............................................................................................... 39
4.1.1 Setting for Media Drives and Executable Files....................................................... 41
4.1.2 Output Device Setting ............................................................................................ 42
4.1.3 Master Balance Adjustment ................................................................................... 43
4.1.4 Monitor Adjustment ................................................................................................ 44
4.1.5 DSC Setup ............................................................................................................. 45
4.2 Data Writing Administration ................................................................................................ 46
4.2.1 Data Writing Statistic Log ....................................................................................... 48
4.2.2 Media Drive Setting ................................................................................................ 50

3
 4.2.3 Optional Software Setting....................................................................................... 51
4.2.4 Service Type Setting .............................................................................................. 52
4.2.5 Index Print Size Selection ...................................................................................... 54
4.3 Print-to-Print Service Administration................................................................................... 55
4.3.1 Registering of Print-to-Print Service ....................................................................... 55
4.3.2 Print-to-Print Service Settings ................................................................................ 56
4.4 Registering of Other Applications ....................................................................................... 58
4.5 Digital Photo Center Administration.................................................................................... 59
4.5.1 Registering of Digital Photo Center Service ........................................................... 59
4.5.2 Digital Photo Center Settings ................................................................................. 60
4.6 Multiple Service Setting ...................................................................................................... 62

5 Operation Test ....................................................................................................................... 64

5.1 Test DSC Printing............................................................................................................... 64
5.2 Test CD Writing .................................................................................................................. 66
5.3 Test Print-to-Print Operation............................................................................................... 69

6 Product Information............................................................................................................. 71
6.1 DI Print Product Information ............................................................................................... 71
6.1.1 Save to FD ............................................................................................................. 71
6.1.2 Log Contents .......................................................................................................... 72
6.2 Data Writing Product Information ....................................................................................... 73
6.2.1 Save to FD ............................................................................................................. 73
6.2.2 Log Contents .......................................................................................................... 74

7 Index........................................................................................................................................... 75

4
 1 Precautions for Installation

1.1 Version of System/Option Software Combination

1. FRONTIER 330 System Software and Optional Software

K :Available ✕ :N/A
A1 A2 B1 B3 B3/B4 B9 C2 C4/C5 C8 C10 C11
Ver.1.0 Ver.3.0 Ver.4.0 Ver.4.1 Ver.1.0 Ver.1.5 Ver.1.7 Ver.4.5 Ver.4.6 Ver.5.0 Ver.5.5 Ver.1.1 Ver.1.0 Ver.1.0
Ver.1.0 ✕ ✕ ✕
✕ ✕ ✕ ✕ ✕ ✕ ✕
Ver.1.5 K K K K K
K K
Ver.2.0 K ✕ K K K K K K

2. FRONTIER 340 System Software and Optional Software

K :Available ✕ :N/A
A1 A2 B1 B3/B4 B9 C2 C4/C5 C8 C10 C11
Ver.1.0 Ver.4.0 Ver.4.5 Ver.2.0 Ver.1.5 Ver.1.7 Ver.4.5 Ver.4.6 Ver.5.0 Ver.5.5 Ver.1.1 Ver.1.0 Ver.1.0
Ver.1.0 K ✕ ✕ ✕ ✕ ✕ ✕
K K K K K K
Ver.2.0 ✕ K K ✕ K K K

3.FRONTIER 350/370/390 System Software and Optional Software

K :Available ✕ :N/A
A1 A2 B1 B3 B5 B6 B7 B8 B9 B11
Ver.4.0 Ver.3.0 Ver.4.0 Ver.5.0 Ver.2.0 Ver.1.0 Ver.1.0 Ver.1.0 Ver.1.0 Ver.1.0 Ver.1.5 Ver.1.0
Ver.6.0
K ✕ K ✕ ✕
Ver.6.6 K K K K K K K
(Note1)
Ver.7.0 K ✕ K K

A1 C2 C4/C5 C8 C10 C11

Ver.1.6 Ver.1.7 Ver.4.1 Ver.4.5 Ver.4.6 Ver.5.0 Ver.5.5 Ver.1.1 Ver.1.0 Ver.1.0
Ver.6.0 ✕ ✕ ✕
K K
Ver.6.6 K K K K K
(Note2) (Note3) K K K
Ver.7.0

Note1: Not available for FRONTIER 390

Note2: Operated only on Windows NT
Note3: Operated only with C4/C5 Ver.4.5 or later

A1: FRONTIER System C2: DI I/O Service

B1: Variety Print C4/C5: DI Print/Data Writing Service
B5: Single Scan Digitizing Function C8: LAN Spool
B8: Hyper Reorder C10: Variety Print Digital
B9: Tone Selection C11: Hyper Retouch Digital
B11: Hyper Retouch
B12: FRONTIER Automatization Support Software

5
 2 Hardware/System Configuration

2.1 Hardware Configuration

2.1.1 FRONTIER 355/375 System

LP1500SC/LP2000SC

SP3000

Imaging Controller HUB

(Example)

Imaging Controller
I/O Box PC Card
Reader
Monitor
Zip Drive

MO Drive
Mouse

CD-R
Drive
Keyboard

Flatbed Scanner

( USB or SCSI connection

for use with Windows 2000 )
FD162B

6
2.1.2 FRONTIER 330/340 System

SLP-800SC/SLP-1000SE

Imaging Controller HUB

(Example)

Imaging Controller
I/O Box PC Card
Reader
Monitor
Zip Drive

MO Drive
Mouse

CD-R
Drive
Keyboard

Flatbed Scanner

( USB or SCSI connection

for use with Windows 2000 )
FD162BC

7
2.1.3 FRONTIER 350/370/390 System

LP1500SC/LP2000SC/LP2500P

SP1500/SP2000/SP2500

Imaging Controller HUB

(Example)

Imaging Controller
I/O Box PC Card
Reader
Monitor
Zip Drive

MO Drive
Mouse

CD-R
Drive
Keyboard

Flatbed Scanner

( USB or SCSI connection

for use with Windows 2000 )
FD162A

8
2.1.4 Imaging Controller System (Example)

Imaging Controller

Flatbed Scanner

Monitor

PC Card
Reader Mouse

Keyboard
Zip Drive

MO Drive CD-R Writer

CD-R Writer

I/O Box

FD163

Memory StickTM, SD Memory Card TM and MicrodriveTM can also be used as media when using Windows ® 2000
system.

9
 2.2 System Preparations

2.2.1 PC and Media Drive Preparations Required SCSI board:

• Adaptec 2940
Prepare the PC, media drives, HUB, and the • Adaptec 2930LP
• Adaptec 29160
cables.

1 PC that meets the following requirements:

Required CD-R:
• Fujifilm CD-R

CPU : Pentium II 400MHz

Hard disk : At least 9GB x 2 drives Required scanner type:
Memory : At least 256MB • MICROTEK ScanMaker 4
• EPSON Expression 1600

2 OS • EPSON Expression 1680

Windows NT4.0 Workstation SP6 or Windows
2000 Professional SP2 IMPORTANT:
Never use the CD-RW media instead of CD-R.

4
SCSI board must be installed beforehand.
HUB and two network cables to connect Frontier

3 Media drives and cables

to HUB and HUB to Imaging Controller.

5
Zip, Jaz, MO, CD-R, PC card, SSFDC, CF,
CRT Monitor
Flatbed scanner, etc.
(SD Memory Card, Memory Stick and Microdrive
• Color Temperature: 6500° K
are supported only with Windows 2000)
• Resolution: 800 x 600 pixels or higher
In Windows 2000, the USB connection is also • Display Color: 32bit
available for the drive media except CD-R.
However, the processing speed in USB connec- 6 “Aspi” manager must be installed. If not, an error
tion is not assured, and correct assignment of may occur when starting “Data Writing” or “Print
drive name may not be done. to Print” software. At the installation of the
Windows NT, “Wnaspi32.DLL” is installed in the
“System32” folder in the “Winnt” folder in the C
Required CD-R drive types:
drive, but it is not activated. To activate it, install
• YAMAHA CRW 400tx
and set up “Wnaspi32.DLL” using any of the
• YAMAHA CRW 4260tx
following ways.
• YAMAHA CRW 4416sx
• YAMAHA CRW 6416sx
(1) Install “EZ-SCSI(CD-ROM)” provided with
• YAMAHA CRW 8424sx
“Adaptec 2940” SCSI board.
• YAMAHA CRW 8824sx
• YAMAHA CRW 2100s-Vk
(2) Install the writing software “EZ-CD creator”
• PLEXTOR CD-R/W PX-W8220Te
provided with the dedicated CD-R drives.
• PLEXTOR CD-R/W PX-W124TSe
(See “Recommended CD-R drive types”
• PLEXTOR CD-R/W PX-W1210TS
shown above.)
• PLEXTOR CD-R/RW PX-W4012TS
(For the above CD-R drives, SCSI connection
is used with both Windows NT4.0 and Win-
dows 2000)

Make sure to use the SCSI connection for the

CD-R drive.

10
2.2.2 Hard Disk Partition 2.2.3 Virtual Memory Setting

During the installation of Windows NT/Windows [In case of Windows NT]

2000, partition your hard disk into two regions: one
for the system and the other for order registration
and spooling (Ex: 4GB for the system and 5GB for
1 On the Desktop, choose [Start] - [Settings] -
[Control Panel].
order registration). For details see the Windows NT/
Windows 2000 setup manual.
2 Click the [System] icon in the “Control Panel”
window.

• The “System Properties” screen appears.

Select [Performance] tab.

Click.

3 Click [Change] under [Virtual Memory] on

[Performance] tab.

• The “Virtual Memory” screen appears.

Click.

Click.

11
 4 In the Drive list, click the drive you want to 4 Click [Change].
change.
• The “Virtual Memory” screen appears.
5 Under “Paging File Size for Selected Drive”, type
Select the drive. Click.
“500” in the Initial Size (MB) and Maximum Size
(MB) boxes.

If the “Paging File Size” is less than 500MB,

make it more than 500MB.
If it exceeds 500MB, make sure to allocate it
more than the physical memory size.

6 Click [Set].

7 Click [OK].

• Operation returns to the “System Properties”

screen.

8 On the “System Properties” screen, click [OK].

• Operation returns to the “Control Panel” window.

Check if the initial size (MB) Click.
and maximum size (MB) are
more than 500MB.

[In case of Windows 2000]

5 In the Drive list, click the drive you want to

1
change.
On the Desktop, choose [Start] - [Settings] -
[Control Panel].
6 Under “Paging File Size for Selected Drive”,

2
make sure that the Initial Size (MB) and
Click the [System] icon in the “Control Panel”
Maximum Size (MB) are more than 500MB.
window.

If the “Paging File Size” is less than 500MB,

• The “System Properties” screen appears.
make it more than 500MB.

3 Click [Performance Options] on [Advanced] tab.

7 Click [Set].

8
• The “Performance Options” screen appears.
Click [OK].

• Operation returns to the “Performance Options”,

so click [OK] to return to the “System Properties”
screen.

9 On the “System Properties” screen, click [OK].

• Operation returns to the “Control Panel” window.

Click.

12
2.2.4 Computer Name Setting 5 In the [Computer Name] box, type “FRONTEND”
and click [OK].
[In case of Windows NT]
• The confirmation message appears.

1 On the Desktop, choose [Start] - [Settings] -

[Control Panel].

2 Click [Network] in the “Control Panel” window.

• The “Network” screen is displayed. Click.

Select [Identification] tab.

6 Click [OK].

• Operation returns to the “Network” screen.

Click.

3 Click [Identification] tab.

4 Move the cursor to the Computer Name and click

[Change].

• The “Identification Changes” screen appears.

Type “FRONTEND”.

13
[In case of WIndows 2000] 5 In the [Computer Name] box, type “FRONTEND”
and click [OK].

1 On the Desktop, choose [Start] - [Settings] -

• The confirmation message appears.
[Control Panel].

2 Click [System] in the “Control Panel” window.

The “System Properties” screen is displayed.
Select [Network Identification] tab.

Click.

6 Click [OK].

• Operation returns to the “System Properties”

screen.

Click.

3 Click [Network Identification] tab.

4 Click [Properties].

• The “Identification Changes” screen appears.

Type “FRONTEND”.

14
2.2.5 Network Protocol Setting 4 If “NetBEUI Protocol” is not found in the “Network
Protocols:”, register it.
[In case of Windows NT]
(1) Click [Add].
IMPORTANT: Make sure to use NetBEUI protocol.
(2) Select “NetBEUI Protocol” and then click

1 On the “Network” screen, click [Protocols] tab.

[OK].

Select [Protocols] tab.

Select [NetBEUI Protocol]. Click.

(3) Complete the registration by following the

messages given.

[In case of Windows 2000]

2 Click “NetBEUI Protocol” in the Network IMPORTANT: Make sure to use NetBEUI protocol.
Protocols and click [Close].
1 On the “Control Panel” screen, double-click
• The “Network Settings Change” message [Network and Dial-up Connections].
appears.

Click.

3 Click [No].

Double-click.

15
 2 Click [Local Area Connection] icon and then click 6 If “NetBEUI Protocol” is not found in the
[Network Identification] tab. “Components checked are used by this
connection:”, register it.
3 Double-click “Local Area Connection” icon.
(1) Click [Install].
• The “Local Area Connection Status” screen
appears. (2) Click [Protocol], and then click the [Add]
button.
Select [Protocol].

Click.
Click.

4 Click [Properties]. (3) Select [NetBEUI Protocol] and then click

[OK].
5 Confirm if “NetBEUI Protocol” in the “Components
Select [NetBEUI Protocol].
checked are used by this connection:” is checked
[√], and if not, check [√] it.
Check if [NetBEUI Protocol] is checked [√].

Click.

If [NetBEUI Protocol] is not found, click [Install].

16
2.2.6 Creating a User Account 3 Type “FRONTIER” in both the [User name] and
[Full Name] columns, and enter a password in
[In case of Windows NT] both the [Password] and [Confirm Password]
columns.

1 On the Desktop, choose [Start] - [Programs] - Type “FRONTIER”.

[Administrative Tools] - [User Manager].

• The “User Manager” screen appears.

Click.

2 In the User menu, click “New User”.

• Check “Password Never Expires” box.

4 Click [Groups].

• The “Group Memberships” screen appears.

• The “New User” screen appears.

5 Choose “Administrators” and click [Add].

6 On the “Group Memberships” screen, click [OK].

7 On the “New User” screen, click [OK].

17
[In case of Windows 2000] 4 Select [Tree]-[Users].

1 On the “Control Panel” screen, double-click

[Users and Passwords].

Select [Tree]-[Users].

5 Select [New User···] from [Action] on the menu

bar.

Double-click.

2 Click [Advanced] tab.

Click [Advanced] tab.

6 Type “FRONTIER” in [User name], [Full name],

[Password] and [Confirm password:] columns.
Type [FRONTIER].

3 Click [Advanced]. Click [Create] then [Close].

Remove the checkmark from “User must change

password at next log-on”, and check [√] “Pass-
word never expires”.

Click.
7 Click [Create] and then click [Close].

18
8 Select [FRONTIER] from the right-hand list (1), 10 Select [Administrators] on the “Select Groups”
and then select [Properties] from [Action] on the screen, and then click [Add] to add it to the list.
menu bar (2). And then click [OK].
Select [FRONTIER] (1). Select [Administrators].

Select [Properties] (2).

9 Click [Member Of] tab, and then click [Add···] Click.

Select [Member Of] tab.

11 Click if “Administrators” exists in the list on
[Member Of] tab of the [FRONTIER Properties]
screen.

Click if “Administrators” exists.

Click.

Click [Apply] then [OK].

12 Click [Apply] and then click [OK].

19
2.2.7 Restarting [In case of Windows NT]

1 On the Desktop, choose [Start] - [Shut Down]. • “(Build 1381: Service Pack 6)” is displayed in the
upper right-hand corner of the Windows NT’s
BLUE starting screen.

[Windows 2000]

Microsoft® Windows NTTM Version 4.0 (Build 1381: Service Pack 6).
2 System Processors [256 MB Memory] MultiProcessor Kernel

2 In case of Windows NT, click “Restart the • The settings take effect after restarting the com-
puter.
computer?” and click [Yes].

[Windows NT]

In case of Windows 2000, select “Restart” and

click [OK].

[Windows 2000]

20
[In case of Windows 2000]

• Check if the Service Pack is properly installed

using the following procedures.

1 On the “Control Panel” window, click [System]

icon.

Click.

• The “System Properties” screen appears.

2 Check that the Service Pack 2 is displayed in the

“System” on the “General” tab.

21
 3 Installation

DI Print Service/Data Writing Software Ver.5.5 can only be operated in the following combination of the system
or other optional software.

FRONTIER 350/370 A1: System Software Ver.7.0 or later

FRONTIER 390 A1: System Software Ver.7.0 or later
FRONTIER 330/340 A1: System Software Ver.2.0 or later
FRONTIER 355/375 A1: System Software Ver.1.5 or later

IMPORTANT: Printing (including negative printing) cannot be performed during the installation.

IMPORTANT: Before starting the installation, perform the post-operational check, and shut down the FRON-
TIER. Do not shut it down by using the emergency stop button.

IMPORTANT: Before updating the “DI Print/Data Writing Service Software [C4/C5]” from Ver.4.5, Ver.4.6 and
Ver.5.0 to Ver.5.5, make sure that there are no orders in the DI Print [C4] and Data Writing [C5]
services, then close the [C4/C5]. When orders remain in the [C4/C5], complete the printing and
writing first, then start updating.
If you start updating while the orders remain in [C4/C5], they will be deleted.

(FRONTIER 330 Ver.2.0 or earlier/350/370/390) (FRONTIER 330/340 Ver.3.0 or later)

(FRONTIER 355/375)

22
 3.1 Standard Setup/Upgrade

For the upgrade, use the same procedures as for the Standard Setup.
Before starting the installation of the DI Print/Data Writing Service Software [C4/C5], perform the Post-operational
check in FRONTIER and shut it down.
To install the DI Print/Data Writing Service Software [C4/C5] Ver.5.5, the Ver.5.0 software must be installed in the Imag-
ing Controller.

1 Click the [Exit] button while pressing the [Shift]

3 Select [Run] from [Start] menu on the Desktop.
key to close the DI Print/Data Writing Service
[C4/C5].
Click [Exit] while pressing [Shift] key.

4 On the “Run” screen, enter “h:\setup.exe”, then

click [OK].

2 Insert the DI Print and Data Writing Service

Software CD into the CD-ROM drive.

The drive name (ex:h:\) varies according to the

CD-ROM drive into which you inserted the
installer CD.

FD201 5 On the “Setup Type Selection” screen, select

[Standard Setup], then click the [Next] button.
Select [Standard Setup].

23
 6 On the “Start Copying Files” screen, click the
[Next] button.

Click.

• Installing starts.

7 Upon completion of installation, remove the CD

from the CD drive, and then restart the Imaging
Controller.

FD202

24
 3.2 Custom Setup/Upgrade

3.2.1 Custom Setup/Upgrade for Use of 3 Select [Run] from [Start] menu on the Desktop.
DI Print/Data Writing Service [C4/C5]

For the upgrade, use the same procedures as for the

custom setup.
Before starting the installation of the DI Print/Data
Writing Service Software [C4/C5], perform the Post-
operational check in FRONTIER and shut it down.
To install the DI Print/Data Writing Service Software
[C4/C5] Ver.5.5, the Ver.5.0 software must be installed
in the Imaging Controller.

1 Click the [Exit] button while pressing the [Shift]

key to close the DI Print/Data Writing Service
[C4/C5]. 4 On the “Run” screen, enter “h:\setup.exe”, then
Click [Exit] while pressing [Shift] key. click [OK].

The drive name (ex:h:\) varies according to the

CD-ROM drive into which you inserted the
installer CD.

5 On the “Setup Type Selection” screen, select

2 Insert the DI Print and Data Writing Service [Custom Setup], then click the [Next] button.
Software CD into the CD-ROM drive.

Select [Custom Setup].

FD201

25
 6 On the “Select Application” screen, click the [DI If you added a hard disk drive for temporary
Print/Data Writing Service Software Ver.5.5] directories, enter its drive name.
button.
9 On the “Enter Text” screen, check if the
“FRONTEND” is selected, and then click the
[Next] button.

Click.
NOTE:
If “MSDE” and “64MB SmartMedia Driver” are
not installed in your system, install them.
(See “3.3 MSDE/64MB SmartMedia Driver
Installation” on page 30.) Click.

7 On the “Setup Type Selection” screen, select [DI 10 On the “Spool Drive Setting” screen, select any
Print/Writing Service]. Then, click the [Next] drive name (ex.“D”) as spool drive, and then click
button. the [Next] button.

Select a Setup type. Click.

8 On the “Working Drive Setting” screen, click the The spool drives can be divided into two regions:
[Next] button. One for “Inspool” and another for “Outspool”.
Registered or digitized images are stored in the
“Outspool”. If you have added a hard disk drive
with a large storage space to the system,
change the drive name to the newly added drive
for storing large-size images.

Click.

26
11 On the “Start Copying Files” screen, click the 3.2.2 Custom Setup/Upgrade for Use of
[Next] button. DI Print Service [C4] Only

For the upgrade, use the same procedures as for the

custom setup.

1 Click the [Exit] button while pressing the [Shift]

key to close the DI Print/Data Writing Service
[C4/C5].
Click [Exit] while pressing [Shift] key.

Click.

• Installing starts.

12 Upon completion of installation, remove the CD

2 Insert the DI Print and Data Writing Service
from the CD drive, and then restart the Imaging Software CD into the CD-ROM drive.
Controller.

FD201
FD202
3 Select [Run] from [Start] menu on the Desktop.

27
 4 On the “Run” screen, enter “h:\setup.exe”, then 7 On the “Setup Type Selection” screen, select [DI
click [OK]. Print Service Only]. Then, click the [Next] button.

The drive name (ex:h:\) varies according to the

CD-ROM drive into which you inserted the
installer CD.
Select a [DI Print Service Only].
5 On the “Setup Type Selection” screen, select
[Custom Setup], then click the [Next] button.
8 On the “Enter Text” screen, click the [Next]
button.

Select [Custom Setup].

6 On the “Select Application” screen, click the [DI

Print/Data Writing Service Software Ver.5.5]
button. Click.

9 On the “Start Copying Files” screen, click the

[Next] button.

Click.

NOTE:
If “MSDE” and “64MB SmartMedia Driver” are
not installed in your system, install them.
(See “3.3 MSDE/64MB SmartMedia Driver
Installation” on page 30.)
Click.

28
 • Installing starts.

10 Upon completion of installation, remove the CD

from the CD drive, and then restart the Imaging
Controller.

FD202

29
 3.3 MSDE/64MB SmartMedia Driver Installation

If your Imaging Controller already has the MSDE/64MB SmartMedia Driver Installed,
skip this section.

3.3.1 MSDE Installation 3 In the “Restart” dialog box, click the [Yes] button.

1 On the “Setup Type Selection” screen, select

[Custom Setup], then click the [Next] button.

Select [Custom Setup].

Click.

2 On the “Select Application” screen, click the

[MSDE] button.
Click.

• MSDE is installed.

30
3.3.2 64MB SmartMedia Driver Installation 4 On the “Welcome” screen, click the [Next] button.

1 On the “Setup Type Selection” screen, select

[Custom Setup], then click the [Next] button.

Select [Custom Setup].

Click.

• The driver is installed right away.

2 On the “Select Application” screen, click the 5 On the “Setup Complete” screen, click the
[64MB SmartMedia Driver] button. [Finish] button.

Click.

3 In the “Confirmation” dialog box, click the [Yes] Click.

button.

Click.

31
 3.4 Backup Order Function

Backup Order Function is the function where you can temporarily store the orders from the external
application (Kiosk, etc.), and later can correct them on the View and Order screen.

3.4.1 Added Functions NOTE:

If the Backup Order Function is installed, process-
By installing the Backup Order Function, the ing may be slower because the back-up processing
from the registered devices is done each time it is
following functions can be used.
executed.

[Printing(C4)] NOTE:
• Re-registration function of printing order This function cannot be uninstalled.
• Test printing on the View and Order screen
NOTE:
To disable this function, edit (comment-out) the
device for backup order function that is defined in
[Writing(C5)]
the “C:\FE\FEIN\InUkBackup.ini” file.
• New services (devices) are added. The following
devices are added to the Digital Service Selec-
tion list.

Service Name Functions

FDi CD1
Three types of FDi CD are added.
FDi CD2 Additional data such viewer can
be written.
FDi CD3

FDi CD with FCD FUJICOLOR CD with FDi CD

(higher- or lower pixels)

Pro CD In this service the order uses the

print size selected in the Print
Size setup in film scanning, while
the original image size is adopted
in the DCS Printing.

• Picture Rotation
The radio buttons for selecting the upper side
are added to the frames on the Image List
screen. To display these radio buttons, add the
checkmark [√] to [Yes] box on [Picture Rotate]
on the Writing Service - Administration screen.

32
3.4.2 Installation • Installation (DOS) screen appears, and it disap-
pears when installing is completed.
Install the Backup Order Function. Installation is
done by running the two batch files.

1 Click the [Exit] button while pressing the [Shift]

key to close the DI Print/Data Writing Service
[C4/C5].
Click [Exit] while pressing [Shift] key.

4 On the “Run” screen, enter

“H:\Merlin\MerlinPatch2.bat”, then click [OK].
Enter “H:\MerlinPatch2.bat”.

2 On the Desktop screen, select [Run] from [Start]

menu.

Click.

The drive name (ex:H:\) varies depending on

your system.

5 On the confirmation (Registry Editor) screen,

click [Yes].

Select [Start] - [Run].

3 On the “Run” screen, enter

Click.
“H:\Merlin\MerlinPatch1.bat”, then click [OK].
Enter “H:\MerlinPatch1.bat”.
6 On the confirmation (Registry Editor) screen,
click [Yes].

Click.
Click.

The drive name (ex:H:\) varies depending on

your system.

33
 • After the restart, the [Backup Order] button and
[Main List/Backup List] tab appear on the Printing
screen.

[Backup Order] button

[Main List/Backup List] tab

34
 3.5 Installation to FRONTIER

3.5.1 [C4/C5] Installation 2 On the “Enter Text” screen, click the [Next]
button.
Install the [C4/C5] in the FRONTIER.

For the upgrade, use the same procedures as for the

standard setup.

1 Insert the DI Print/Data Writing Service Software

[C4/C5] installing or upgrading CD into the CD
drive, and then restart the FRONTIER after
performing the Post-operational Check.

[FRONTIER 330/340/355/375]
Click.

3 On the “Start Copying Files” screen, click the

[Next] button.

[FRONTIER 350/370/390]

Click.

• Installing starts.

4 Upon completion of installation, restart the

FRONTIER.

35
3.5.2 Installation Information Setup 3 Select [41 System Operation Setup and Check] -
[41F Installation Information Setup] and click
Set the external file I/O to ON to communicate with [START].

the Imaging Controller.

■ FRONTIER 350/370/390

1 On the “Main Menu” screen, select [Setup and

Maintenance] and click [OK].

Click.

4 Click [Option].

2 In the “Log-in” dialog box, select [Laboratory

Manager], then enter the password “0000” and
click [OK].
Select “Laboratory Manager”.

Click.

5 On the “Optional Device Setting” screen, set

[External File I/O] to [YES], then click [OK].
Click [YES].

Click.

Click.

36
6 On the “[41F] Installation Information Setup” 3 Select [01 System Operation Setup and Check] -
screen, click [OK]. [0140 Installation Information Setup].

7 In the confirmation dialog box, click the [OK]

button.

Click.

■ FRONTIER 330/340/355/375 4 On the “Installation Information Setup” screen,

click the [Option] button.

1 On the “Main Menu” screen, click the [Setup and

Maintenance] button.

Click.

Click.

5 On the “Optional Device Setting” screen, set

[External File I/O] to [YES] and then click the
The above is an example of a FRONTIER 340 [OK] button.
screen.
Set [External File I/O] to [YES].

2 Enter the password “7777”, and then click the

[OK] button.

Enter “7777”.

Click.

6 In the confirmation dialog box, click the [OK]

button.
Click.

37
3.5.3 Print Size Setup ■ FRONTIER 330/340/355/375

On the FRONTIER, set the print sizes to be used in The following procedures use the FRONTIER 355 as
DIGITAL IMAGING PRINT SERVICE. example.

■ FRONTIRER 350/370/390 1 Perform Steps 1 and 2 in “3.5.2 Installation

Information Setup” (page 36) to open the “Setup

1 Perform Steps 1and 2 in “3.5.2 Installation and Maintenance” screen.

Information Setup” (page 36) to open the “Setup
and Maintenance” screen. 2 Select [02 Print Condition Setup and Check] -
[0220 Print Size Setup] to open the “Print Size

2 Select [Print Condition Setup and Check] - [Print Setup” screen.

Size Setup (424)] to open the “Print Size Setup” Select [02 Print Condition Setup and Check]
screen. - [0220 Print Size Setup].

3 Set the print size.

3 Set the print size.

IMPORTANT:
When registering the print size, never use a
size designation with more than five charac-
ters.
If used, an error will occur when the connec-
tion is established with the Imaging Controller
at the pre-operational check.

4 Click the [OK] button.

5 Repeat Steps 3 and 4 for each print size.

IMPORTANT:
When registering the print size, never use a
size designation with more than five charac-
ters.
If used, an error will occur when the connec-
tion is established with the Imaging Controller
at the pre-operational check.

4 Click the [OK] button.

5 Repeat Steps 3 and 4 for each print size.

38
 4 Setting the Imaging Controller

4.1 Print Service Administration

Perform the print service administration settings on the Print Service Administration screen. Here,
you can perform or change the settings such as the output device, media drive, etc.

1 On the “Printing” screen, click the [Admin.] 2 In the “Password” dialog box, enter “DI”, and then
button. click the [OK] button.

Click. Enter “DI”.

Click.

6 5 9

1 10
11
2 12
13
14
3 15
16
17

18

7 8 19

No. Item Description

1 Index Print Select [Yes] to print the DSC index print.
2 Minimum Image Size Set the printable minimum image size, normally 20KB to avoid the registration of
too small images as such as thumbnails.
If trying to register the images with less than the set size, the following message
appears on the Order Registration screen.

39
 No. Item Description
3 Automatic Transaction When [Auto.] button is turned ON, select a type of the automatic transactions on
for all Frames the “Printing” screen.
• to “Select All and Set”:
Automatic processing to the stage to “Select All and Set”. Click [Order Regist.] to
complete an order.
• to “Order Registration”:
Automatic processing to the stage to “Order Registration”. The registration is
completed simply by selecting media.
• to “View All Image”:
Automatic processing to the stage to “View and Order”. After the media selection,
you can monitor and adjust the images on the “View and Order” screen.
4 Back Print Select if the Back Printing is to be done or not. Add a checkmark [√] to select it.
5 Default Print Q’ty Sets the default number of prints, index print and large index print sheets to be
output.
6 Key Step Set the CMYD key steps used on the “View and Order” screen (Recommended
values: CMY: 3, DcDmDy: 5).
7 Machine ID Identifies the multiple Imaging Controllers with this ID (a character of an alphabet
except “N” and “R”). This ID is added to the head of the order number.
8 Auto Correct - Disable If this is checked [√], the auto correction is not applied to the image.
9 Help Displays the help screen.
10 Version Info. Displays the version information about this Software.
11 Statistic Log Stores the statistic information for each registered image data file into the FD, and
monitor them.
12 Monitor Adjust Displays the “Monitor Adjust” screen and matches the color balance of the monitor
to the print on the “View and Order” screen.
13 Master Balance Set the color master balance for printing for each print service. Normally set “0”.
14 Media Drive Set the media drives and relate them to the appropriate media icon.
15 Output Device Select the device name of the printer or other devices to be used.
16 Multiple Service Displays the “Multiple Services - Administration” screen.
17 DSC Setting Displays the “DSC Setup Setting” screen, where you can adjust the color, tone and
sharpness settings.
18 [OK] button Makes the settings effective. Control returns to the Printing screen.
19 [Cancel] button Cancels the settings. Control returns to the Printing screen.

40
4.1.1 Setting for Media Drives and Executable Files

On the Print Service Administration screen, click [Media Drive] to open the Media Drive Setting screen, on
which you set the media drives and relate them to the appropriate media icon.

2 3 4 5

No. Item Description

1 Drives1 to18 The selected drive icons appear on the Printing screen.
2 Icon Display Displays the icons to be used.
3 Name Shows the drive name or software name.
4 Drive Select the drive letter and relate it to the icon.
5 File Path Specify the full path to the application.
Path and drive cannot be specified simultaneously.
6 [OK] button Makes the settings effective. Control returns to the Print Service - Administration
screen.
7 [Cancel] button Cancels the settings. Control returns to the Print Service - Administration screen.

When using the external executable files such as PtoP and Digital Photo Center, set the icon and file path as
shown below.

Icon File Path

PtoP C:\FE\scanner\scanapp.exe
Digital Photo Center (LAN connections) DPC1 to DPC9 C:\FE\kiosk\kiosk.exe
Digital Photo Center (OFF line) DPC-Media C:\FE\kiosk\kiosk.exe X
Add “X” (drive name for DPC-Media). A space must be
used to separate File Path from drive name for DPC-
Media.

41
4.1.2 Output Device Setting

On the Print Service Administration screen, click [Output Device] to open the Output Device Setting screen,
on which you relate the output device to the icons.

IMPORTANT:
These settings can be done only if the pre-operational check is completed on the FRONTIER 330/350/370/
390.

2 3 4 5

Default print size

cannot be set in the
“Multiple” service.

6
7

No. Item Description

1 Output Devices1 to 8 The icons of the output devices appear on the Printing screen in this order.
2 Icon Selection Select the desired output device icon by clicking it.
3 Icon Name Specify the device name under the icon using up to 8 characters.
To use the Hyper-Retouch Service [C11], install it beforehand.
4 Device This information is registered to the system at the time of “Pre-operational check” in
FRONTIER.

FRONTIER Device Name

330 SP-800sRGB or SP-800PD
340 SP-1000sRGB or SP-1000PD
350/370 SP-1500/2000sRGB or SP-1500/2000PD
390 SP-2500sRGB or SP-2500PD
355/375 SP-3000sRGB or SP-3000PD

42
 No. Item Description
5 [Print Size] button Displays the “Print Size Setting”
screen.
These buttons set the default values
of DSC/Media, DPOF Print, Index
print and Large Index. Press [Print
Size] button to set the desired print
size for each print service. This value
will be displayed on the “Printing”
screen. Once the size is specified as
default, this value will be displayed.
In the “Multiple” service, the
default print size cannot be
selected.

6 [OK] button Makes the settings effective. Control returns to the Print Service screen.
7 [Cancel] button Cancels the settings. Control returns to the Printing screen.

4.1.3 Master Balance Adjustment 2 Click [OK] button to make the settings effective.
Control returns to the Print Service -
On the Print Service Administration screen, click Administration screen.

3
[Master Balance] to open the Master Balance
Click [Cancel] button to cancel the settings.
screen, on which you set the color balance for Control returns to the Printing screen.
printing for each print service.

The settings done on this screen are only applied to

the print, not to the CD-R writing.

1 Set the master balance with the value from -99%

to +99% for each service Digital Still Camera
Print, CD-R Reprint or Media Print.

43
4.1.4 Monitor Adjustment 5 When the sample print is output, open the
Monitor Adjust screen again. And then adjust the
On the Print Service Administration screen, click CMY while checking the color on the print.

6
[Monitor Adjust] to open the Monitor Adjust screen,
And then click [Apply] to apply the adjusted
on which you match the color balance of the values to the monitor.
monitor to the print.

[Auto Correction]
7 Repeat Step 5 several times, and then click [OK]
to register the values. Control returns to the
Printing - Administration screen.

8 Click [OK] button to make the settings effective.

Control returns to the Print Service -
Administration screen.

9 Click [Cancel] button to cancel the settings.

Control returns to the Printing screen.

[No Correction]

1 Select [Auto Corr.] tab or [No Corr.] tab.

2 On the Monitor Adjust screen, click [Sample

Print] to register the sample print order.

3 After the disappearance of the sandglass icon,

click [Cancel] to return to the Print Service -
Administration screen. And then click [Cancel] to
return to the Printing screen.

4 Print the order ZA9998 (No Correction) or

ZA9999 (Auto Correction) on FRONTIER.

• “CX MX YX” is printed on the back of the sample

print.

44
4.1.5 DSC Setup

On the “DSC Setup Setting” screen, you can set and change the initial parameters for color, tone and
sharpness adjustment for DSC printing. On the “Print Service - Administration” screen, click [DSC Setting].

No. Item Description

1 Color Intensity Set up the chroma saturation value from -2 to +4.
2 Gradation Adjustment Select the type of Pro DI Gamma from “Hard2” to “Soft3”.
3 Hyper Tone Select the mode of the Hyper Tone.
4 Sharpness Select “Noise Reduction” or “Standard (USM)” for sharpness type.
5 [Help] button Displays the Help screen.
6 [OK] button Makes the settings effective. Control returns to the “Print Service - Administration”
screen.
7 [Cancel] button Cancels the settings. Control returns to the “Print Service - Administration” screen.

45
 4.2 Data Writing Administration

1 On the “Writing” screen, click the [Admin.] 2 In the “Password” dialog box, enter “DI”, and then
button. click the [OK] button.

Click. Enter “DI”.

Click.

4 3

11
1
2
12
5 13
14
15

6
7
8
16
9
10 17

18 19

No. Item Description

1 Adapter No. and SCSI ID Select an appropriate combination of SCSI HOST Adapter number and SCSI ID for
the CD-R drive.
2 CD-R Drive Name Select the drive name for the CD-R drive.
3 CD-ROM Drive Name Select the drive name for the CD-ROM drive.

46
No. Item Description
4 Verify Type Selection • Verify after writing (new CD-R):
Check the box to verify the CD-R after writing in a new CD writing.
Normally remove the checkmark [√].
• Verify after writing (additional data):
Check the box to verify the CD-R after writing in an additional writing.
Normally checkmark [√].
5 Media Drive Displays the drive set for writing on the Media Drive Setting screen.
6 Media Drive Setting Displays the Media Drive Setting screen.
7 Optional Software Displays the application software set on the Optional Software Setting screen.
Setting [Setting] button:
Displays the Application Software Call Setup screen.
8 CD-R Index Setting Set the device for printing the CD-R index and large-index prints, and their print
size, and then set “Yes” or “No” to print them.
[Device]:
Select the device for printing the CD-R index or large-index prints.
For large index print, normally select “A4 (210x297mm)” or “8R (203x254mm.
254x203mm)”
9 Print Size Click [Select] to display the Print Size Selection screen.
10 Index/Large Index Sets the default value for “Yes” or “No” to Index/Large Index on Image List screen.
11 [Help] button Displays the Help screen.
12 Version Info. Displays the version information.
13 Statistic Log Display the Statistic Log screen.
14 Service Type Setting Displays the Service Type Setting screen.
15 Multiple Service Displays the Multiple Service screen. (See “4.6 Multiple Service Setting” on page
62.)
16 Writing Speed Select [Fast] or [Normal] for data writing speed.
[Fast] : maximum capability of device
[Normal] : octuple speed
17 Data Delete Interval Set up the time (min) for the data to be deleted after completing processing.
Range : 0-999
18 [OK] button Stores the settings and exits this screen.
19 [Cancel] button Exits this screen without storing the settings.

47
4.2.1 Data Writing Statistic Log

On the Writing Service Administration screen, click [Statistic Log] to open the Log screen, on which you
display and store the statistic log. (For details of product information, see “6 Product Information”.)

3 4 5

1
2 6

7 8

No. Item Description

1 Period Displays the period during which the statistic log is accumulated.
2 Writing Total Displays the total copies of writing during the period.
3 Service Displays the writing service type.
4 Copies Displays the number of copies.
5 Images Displays the number of images.
6 [Help] button Displays the Help screen.
7 [Save] button Saves the statistic log to FD. As the log has the “CSV” format, it can be monitored
by using the spreadsheet software.
8 [Return] button Exits this screen.

48
 1

No. Item Description

1 Starting date Specify the starting date to log.
2 Saving days Specify the number of days to be saved.
3 Path to save Shows the drive/path where the log file will be output.

In the above dialog box, click [Yes] to remove the Writing log. Note that the Writing log can be removed only in
this dialog box, not on the “Product Information” screen.

Note that the removed log is never restored.

49
4.2.2 Media Drive Setting

Select the name, icon and output path and relate them for each media drive other than the CD-R media. The
following three writing services are registered as default.

CD-R 4base JPG

FUJICOLOR CD(4base,JPG)
Free Export BMP

Set the media type on this screen, and then make Service Type Settings on the Service Type Setting screen.
(See “4.2.4 Service Type Setting” on page 52.)
On the Writing Service Administration screen, click [Media Drive Setting] to open the Media Drive Setting
screen.

1 2 3

6 7

No. Item Description

1 Icon Select icons for displaying on the Main screen.
2 Drive Set the drive letter for the writing drive.
3 Output Path Enter the directory name with the full path for writing to HD or network drive.
4 [Brows...] button Displays the Browse screen for selecting the directory. The selected directory
appears in the Output Path box.
5 [Help] button Displays the Help screen.
6 [OK] button Stores the settings and exits this screen.
7 [Cancel] button Exits this screen without storing the settings.

50
4.2.3 Optional Software Setting

On the Writing Service Administration screen, click [Setting] in the Optional Software Setting field to open the
Optional Software Setting screen, on which you can set the FUJIFILM optional software (up to three different
packages).
For example, when using the Digital Photo Center, use the pull-down menu to select “Digital Reorder”, and
then specify “C:\FE\DR\DigitalReorder.exe” as Path for the Optional Software.

2 3

1 4

No. Item Description

1 Icon Select the icon for the software.
2 Path for the Optional Enter the full path name to locate the selected software.
Software
3 [Help] button Displays the Help screen.
4 [Brows...] button Displays the file selection screen for selecting the file. The selected file appears in
the Path for the Optional Software Output Path. Select only the file with “exe”
extension.
5 [OK] button Stores the settings and exits this screen.
6 [Cancel] button Exits this screen without storing the settings.

51
4.2.4 Service Type Setting

Use the “Service Type Setting” screen for setting the type of several writing service combination of Media
Type, File Format and Image Size.
On the Writing Service Administration screen, click [Service Type Setting] to open the Service Type Setting
screen.

1 2 3 4 5

6 7 8

No. Item Description

1 Service Name Displays the service name with the media type, file format and image size.
The selected service name is displayed on the Output Device Selection screen
when performing Digital Image Export on the FRONTIER.
2 Media Type Displays the media type for the writing service.
Supported media type: CD-R
Free Export (same function as C2: BMP Export provides)
3 File Format Displays the selected image file format.
Supported file format: JPG (Exif-JPG), FPX, BMP, FUJICOLORCD
4 Image Size (Base) Displays the type of the image size.
Supported image size: 1base, 4base, 16base, Free Size
5 [Help] button Displays the Help screen.
6 [Set] button Register the service name with the media type, file format and image size, and add
it to in the list.
7 [Delete] button Deletes the selected service name.
8 [Return] button Exits this screen.

52
Restrictions for Service Type Combination

(1) When selecting “FREE EXPORT” as Media Type, only “Print Size” can be specified as Image Size.
(2) When selecting “FUJICOLOR CD” as File Format, only “4base” as Image Size and “CD-R” as “Media
Type” can be selected.
(3) When selecting “FD” as Media Type, only “1base” can be selected as Image Size.

The following table shows the relation between Media Type, File Format and Image Size.

Service Composition

Image Size
Media Type File Format
1Base 4Base 16Base Free Size
FPX
JPG Available Available Available Available
BMP
CD-R
FUJICOLOR CD N/A Available N/A N/A
FDi CD N/A Available N/A N/A
CD Pro N/A N/A N/A Available
FPX
ZIP/JAZ/MO/
JPG Available Available Available N/A
HD1 to 6
BMP
FD JPG Only Film Scan N/A N/A N/A
JPG
Free Export N/A N/A N/A Available
BMP

53
4.2.5 Index Print Size Selection

On the Writing Service Administration screen, click [Select] in the CD-R Index Setting field to open the Print
Size Selection screen, on which you select the print size for the index print.

This service is available only for film scanning.

1 2 3 4 5 6

No. Item Description

1 No. Displays the serial number.
2 Name Displays the print size name.
3 Width (mm) Displays the paper width (mm).
4 Feed (mm) Displays the paper feed (mm).
5 Width (pixel) Displays the paper width (pixel).
6 Feed (pixel) Displays the paper feed (pixel).

54
 4.3 Print-to-Print Service Administration

Perform the Print-to-Print service settings on the Administration screen.

4.3.1 Registering of Print-to-Print Service 4 Set the icon and file path as shown below.

Icon File Path

Set up the file path to the executable file for the
Print-to-Print Service on the “Print Service - PtoP C:\FE\Scanner\scanapp.exe
Administration” screen.

1 On the “Printing” screen, click the [Admin.]

button.

Click.

Select the icon file path.

5 Click the [OK] button.

2 In the “Password” dialog box, enter “DI”, and then

click the [OK] button.

Enter “DI”.

Click. Click.

3 On the “Print Service - Administration” screen,

6 On the “Print Service - Administration” screen,
click the [Media Drive] button. click the [OK] button.

Click. Click.

55
4.3.2 Print-to-Print Service Settings 2 On the “Print-to-Print” screen, click the [Admin.]
button.
Set up the administrative items for Print-to-Print Click.
Service.

1 On the “Printing” screen, select the output device

and then click the [PtoP] button.

Select the output device.

Click.

3 Perform the administration work as shown below.

5 1

2
3
4

8
9

No. Item Description

1 Output Device Select the output device from the Output Device pull-down menu.
2 Print Size Select the default print size from the Print Size pull-down menu.

56
No. Item Description
3 TWAIN Source Select the TWAIN source from the TWAIN Source pull-down menu.
Enter any of the following TWAIN sources.
Microtek Scanmaker 4: Microtek ScanWizard(32bit)
EPSON Expression 1600/1680: EPSON TWAIN Pro(32bit)
4 Scanner Type Select the scanner type from the Scanner Type pull-down menu.
5 Scanner Balance Adjust the master color balance for this service after the fine scanning.
(Value: -99 to +99)
6 Monitor Balance Adjust the monitor color balance for this service after the fine scanning.
(Value: -99 to+99)
7 Contrast Adjust the contrast for the highlight or shadow part of the image after the fine
scanning. (Value: -5 to +5)
8 [OK] button Allows all settings to take effect then returns to the main screen
9 [Cancel] button Cancels all settings then returns to the main screen.

5 and 6 can be set only after the fine scanning is completed.

57
 4.4 Registering of Other Applications

Set up the file path to the executable file for other applications on “Writing Service - Administration”
screen. This section explains how to set up the Digital Reorder service application.

1 On the “Writing” screen, click the [Admin.] Set up the icon and file path.
button.

Click.

4 Click the [OK] button.

2 On the “Writing Service - Administration” screen,

click the [Setting] button in the [Optional
Software Setting] field.

Click.

5 On the “Writing Service - Administration” screen,

Click. click the [OK] button.

3 On the “Optional Software Setting” screen, set

up the icon and file path as shown below.

Icon File Path

Reorder C:\FE\DR\DigitalReorder.exe

Click.

58
 4.5 Digital Photo Center Administration

Digital Photo Center is an in-store order terminal that is connected to the Imaging Controller.
When using it, perform the Digital Photo Center service settings on the Administration screen.

4.5.1 Registering of Digital Photo Center 4 Set the icon and file path as shown below.
Service
Icon File Path

Set up the file path to the executable file for the DPC1 to DPC9 C:\FE\kiosk\kiosk.exe
(LAN)
Digital Photo Center Service on the “Print Service -
Administration” screen. DPC-Media C:\FE\kiosk\kiosk.exe X
(OFF-line) Add “X”

1
(drive name for DPC-MEdia)
On the “Printing” screen, click the [Admin.]
button.
Click.

Set the icon and file path.

2 In the “Password” dialog box, enter “DI”, and then

click the [OK] button. 5 Click the [OK] button.

Enter “DI”.

Click.

3 On the “Print Service - Administration” screen,

click the [Media Drive] button.
Click.
Click.

59
 6 On the “Print Service - Administration” screen, 4.5.2 Digital Photo Center Settings
click the [OK] button.
Set up the administrative items for Digital Photo
Center Service.

1 On the “Printing” screen, click the [DPC1] to

[DPC9] or [DPC-M] button.

Click [DPC1] to [DPC9] or [DPC-M].

Click.

2 On the “Digital Photo Center” screen, click the

[Admin.] button.

Click.

60
3 Perform the administration work as shown below.

No Item Description
1 Print Setting Select the name of the device currently connected and the print size to be used.
The information will be registered in the FRONTIER data base.
Click the [Spool Setting] to display the following “Spool Setting” screen.

■ Spool Setting Screen

No Item Description
1 Spool Setting Specify the name of the folder for the storing spool. The name must be specified by
the full path name such as D:\DPCdata\. Normally enter the following values.
Root Path: D:\DPCdata
Frontier Print: pcpr
DPC Print: aldn

61
 4.6 Multiple Service Setting

The Multiple Service is a service that provides multiple order registration at a time of film scanning
or image entry from the Digital Media. To use this service, register a combination of output devices
beforehand. Use the following procedures to register it.

On the “Print Service - Administration” screen or “Writing Service - Administration” screen, click [Multiple
service] button.

• The “Multiple Service - Administration” screen appears.

2

9
10
3

4
5
6

11 12 13

No Item Description
1 Multiple Service List Lists up the names of the multiple services that were registered.
2 Multiple Service Shows the selected service contents.
Composition
3 Multiple Service Name Enter the name of the service in this space.
4 Print Output Device Select an output device. This information is registered to the system at the time of
“Pre-operational check” in FRONTIER.
5 Image Writing Service Select a writing service to be registered.
6 Image Use Service Select it when using Digital Reorder or NET service.
7 Other (Not used)
8 [Help] button Displays the Help screen.
9 [1 Line Up] button Moves the selected service upward in the Multiple Service List.
10 [1 Line Down] button Moves the selected service downward in the Multiple Service List.
11 [Entry] button Adds the selected service to Multiple Service List.
12 [Delete] button Removes the selected service from Multiple Service List.
13 [Return] button Returns to the Print Service - Administration screen.

62
■ Setting Procedures

1 Select the items to be serviced in the “Service Composition”.

2 Enter the name of the multiple service in the “Multiple Service Name”.

3 Click the [Entry] button.

• The created service is added to the “Multiple Service List”.

4 Click the [Return] button.

• Control returns to the “Print Service - Administration” screen or “Writing Service - Administration” screen.

63
 5 Operation Test

Perform the test DSC printing, CD writing, and Print-to-Print operation.

5.1 Test DSC Printing

1 Set the media including the image(s) in the drive. 4 Click the [Set] button to list up the images in the
“Order Specification Column”.

FD214

2 Select the printing device in the [OUTPUT] field,

and then any of the media in the [INPUT] field. Click.

Select the media.

5 Click the [Order Regist.] button.

Select the printing device.

3
Click.
Find the folder, and then select the image(s).

6 The “Confirmation” dialog box appears.

Select the image(s).

64
7 Remove the media from the drive. 9 Print the registered images with FRONTIER.

FD124

8 Click the [OK] button.

(FRONTIER 350/370/390)

Click.

(FRONTIER 330/340)

(FRONTIER 355/375)

65
 5.2 Test CD Writing

1 Set the media including the image(s) in the drive. 4 Find the folder, and then select the image(s).
Select the image(s).

FD214

2 Select the writing device in the [OUTPUT] field,

and then any of the media in the [INPUT] field.

Select the writing device.

5 Click the [Set] button to list up the images in the
“Order Specification Column”.

Select any of the media.

Click.
3 On the “Service Select” screen, click the [OK]
button. 6 Click the [Order Regist.] button.

Click.

Click.

66
7 The “Confirmation” dialog box appears. 11 Double-click the order in the [Order Registration]
Status field.

8 Remove the media from the drive.

Double-click.

12 On the Image List screen, check the image(s),

and then click [OK] button.

FD124

9 Click the [OK] button.

Click.

10 Click the [Writing] icon to display the “Writing” 13 Insert the CD-R into the drive.
screen.
Click the [Writing] icon.

C45019

67
14 Click [OK] button. In case of media writing, insert
the specified media instead of CD-R.

Click.

15 Writing is started.

16 Click the [OK] button.

Click.

17 Remove the CD-R from the drive.

C45020

68
 5.3 Test Print-to-Print Operation

1 Click [PtoP] in the [INPUT] field. 4 Click the [Add image to Order] button.

Click.

2 Set the photo on the scanning table glass. 5 Click the [Order Regist] button, then the [Return]
button.

FD191
6 Remove the photo from the scanner and store it
in a safe place.

3 Click the [Fine Scan] button.

FD192

69
 7 Print the registered images with FRONTIER.

(FRONTIER 350/370/390)

(FRONTIER 330/340)

(FRONTIER 355/375)

70
 6 Product Information

The product information log can be monitored on the “Log” screen called by clicking the
[Statistic Log] button on the “Order Reception - Administration” screen. These log data stored in
the “C:\FE” folder can also be copied into the FD and can be monitored and analyzed.

6.1 DI Print Product Information

6.1.1 Save to FD 3 Insert a formatted 1.44MB FD into the FD drive.

1 Click the [Statistic Log] button on the “Print

Service - Administration” screen.

Make sure to use a new formatted FD.

• Upon completion the copy, the message appears.

4 Click the [OK] button.

Click the [Statistic Log] button.

• The “Log” screen appears.

2 Click the [Save to FD] button.

Click the [Save to FD] button.

71
6.1.2 Log Contents

Monitor the statistic log information using some editor, or spread sheet software.

Example of Data Items:

1 Order NO. 7 Camera model (only EXIF)

2 Reception date 8 Flash No/Yes
3 Order file version 9 Format*1
4 Order file creating date 10 Print Q'ty
5 Driver 11 File name
6 Application name 12 print size

*1 “Win” appears also for Mac processing because it is converted to Win format in the application software.

1 2 3 4 5 6 7 8 9 10 11 12
A00650 2004/9/ V1.00 2004/9/4 F-DI Net Serner Win 10 DPC001.FPX POST
420:53 V2.00 CARD
A00656 2004/9/ FUJIFILM YES Win 1 DSCF0013.JPG DSC
711:50 FinePix500
A00661 2004/9/ FUJIFILM NO Win 1 DSC00001.JPG DSC
711:57 FinePix700
A11664 2004/9/ NIKON E900 NO Win 1 DSC00001.JPG DSC
712:02
A00668 2004/9/ FUJUFILM NO Win 1 DSC00001.JPG DSC
712:07 DS-30
A00669 2004/9/ RICOH DC-4 YES Win 1 RIM0009.JPG DSC
712:07
A00674 2004/9/ Win 1 SONYMVCFD7 DSC
716:09 .JPG
A00011 2004/9/ V1.00 2004/6/30 phex-win-v1.50 PICTURE.EXE Win 1 4.FPX A5
716:16
A00030 2004/9/ V1.00 2004/9/7 PD-WIN -V1.50 MAMEW9.EXE Win 3 2.FPX C
714:07
A00030 2004/9/ V1.00 2004/9/7 PD-WIN -V1.50 PHOTOS01.DLL Win 10 4.FPX POST
814:07 CARD

72
 6.2 Data Writing Product Information

6.2.1 Save to FD 4 Insert a formatted 1.44MB FD into the FD drive.

1 Click the [Statistic Log] on the “Writing Service - Make sure to use a new formatted FD.
Administration” screen.
• Log file is copied FD.

Click the [Statistic Log] button.

• Upon completion the copy, the message appears.
• The “Log” screen appears.
5 Click the [Yes] button.
2 Click the [Save to FD] button.

3 On the “Save Statistic Log” screen, select

[Starting date] and [Saving days], then click the
[OK] button.

73
6.2.2 Log Contents

Monitor the statistic log contents using some editor, or spread sheet software.

File Contents

[CD-ID No.]. . . . . . . . . . . . . . . . . . . . . . . . . . 12digits

[Order Number] . . . . . . . . . . . . . . . . . . . . . . 6digits
[NEW / ADD] . . . . . . . . . . . . . . . . . . . . . . . . NEW / ADD
[Number of CD-R Index Prints] . . . . . . . . . . 1digits
[Number of Images] . . . . . . . . . . . . . . . . . . . 3digits
[Creating Date]. . . . . . . . . . . . . . . . . . . . . . . year / month / day / hour / minute / second
[Media Type]. . . . . . . . . . . . . . . . . . . . . . . . . CD-R (fixed)
[Version] . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 (fixed)
[FRONTIER]. . . . . . . . . . . . . . . . . . . . . . . . . FRONTIER TYPE

Sample Output

CD-ID Order NEW/ADD Index Number Creating Date Media Type Version FRONTIER
Number of Images

106717100378 900002 NEW 5 192 2004/1/1213:49 CD-R 1 SLP1000_Input

106717100368 900007 ADD 1 40 2004/1/1412:31 CD-R 1 SLP1000_Input

106717100382 900008 NEW 5 200 2004/2/1414:05 CD-R 1 SLP1000_Input

106717100384 1 ADD 4 160 2004/2/1615:37 CD-R 1 SLP1000_Input

106717100383 30 NEW 1 1 2004/2/2216:48 CD-R 1 SLP1000_Input

74
 7 Index

Numerics M
64MB SmartMedia Driver Installation ..................... 31 Master Balance Adjustment ..................................... 43
Media Drive Setting ................................................... 50
B Monitor Adjustment ................................................... 44
Backup Order Function ............................................. 32 MSDE Installation ...................................................... 30
———Added Functions ............................................ 32 MSDE/64MB SmartMedia Driver Installation ........ 30
———Installation ....................................................... 33 Multiple Service Setting ............................................ 62

C N
[C4/C5] Installation .................................................... 35 Network Protocol Setting .......................................... 15
Computer Name Setting ........................................... 13
Creating a User Account .......................................... 17 O
Custom Setup/Upgrade ............................................ 25 Operation Test ........................................................... 64
Custom Setup/Upgrade for Use of Optional Software Setting ........................................ 51
DI Print Service [C4] Only ................................. 27 Output Device Setting ............................................... 42
Custom Setup/Upgrade for Use of
DI Print/Data Writing Service [C4/C5] ............. 25 P
PC and Media Drive Preparations .......................... 10
D Precautions for Installation ......................................... 5
Data Writing Administration ..................................... 46 Print Service Administration ..................................... 39
Data Writing Product Information ............................ 73 Print Size Setup ......................................................... 38
Data Writing Statistic Log ......................................... 48 Print-to-Print Service Administration ...................... 55
DI Print Product Information .................................... 71 Print-to-Print Service Settings ................................. 56
Digital Photo Center Administration........................ 59 Product Information ................................................... 71
Digital Photo Center Settings .................................. 60
DSC Setup .................................................................. 45 R
Registering of Digital Photo Center Service .......... 59
F Registering of Other Applications ........................... 58
FRONTIER 330/340 System ..................................... 7 Registering of Print-to-Print Service ....................... 55
FRONTIER 350/370/390 System.............................. 8 Restarting.................................................................... 20
FRONTIER 355/375 System ..................................... 6
S
H Save to FD ........................................................... 71, 73
Hard Disk Partition..................................................... 11 Service Type Setting ................................................. 52
Hardware Configuration.............................................. 6 Setting for Media Drives and Executable Files ..... 41
Hardware/System Configuration ............................... 6 Setting the Imaging Controller ................................. 39
Standard Setup/Upgrade.......................................... 23
I System Preparations ................................................. 10
Imaging Controller System (Example) ..................... 9
Index Print Size Selection ........................................ 54 T
Installation ................................................................... 22 Test CD Writing.......................................................... 66
Installation Information Setup .................................. 36 Test DSC Printing ...................................................... 64
Installation to FRONTIER ......................................... 35 Test Print-to-Print Operation .................................... 69

L V
Log Contents ....................................................... 72, 74 Version of System/Option Software Combination .... 5
Virtual Memory Setting ............................................. 11

75
FAX : 81-3-5484-0454

Questionnaire concerning This Manual

Fujifilm’s Technical Division Photo Products Marketing would be most grateful if you would make copies of this
form, then complete and send them to us by FAX.
Your opinions will contribute greatly to an accurate assessment of the overall quality of each manual.
All questions can be answered by ticking [✓] the appropriate box(es), but in addition to these answers, please
provide us with your written comments in the lined spaces following each block of questions.

Title : FRONTIER Series

DI Print/Data Writing Service Software Ver.5.5
Manual Title and Reference Number INSTALLLATION MANUAL
Reference Number : PP3-A1001E2

Name :

Your Name and Company

Company :

E-mail Address :

Your E-mail Address and FAX Number

FAX Number :

Question 1 • How would you rate this manual overall?

(1) Very easy to use and understand (2) Fairly easy to use and understand
(3) Slightly difficult to use (4) Very difficult to use and understand
and understand
• Please provide us with your reasons and comments.

Question 2 • Have you found any technical errors, errors in spelling, or missing words in this manual?
Yes No
• If you have ticked (Yes), please let us know what these errors and missing words are.

Question 3 • How would you rate the writing (language, choice of words/phrases, etc.) and the illustrations/
diagrams, etc.?
(1) Clear and easy to follow (2) Should be simplified
(3) Difficult to follow
(1)’ [Illustrations, etc.] Of adequate size
(2)’ [Illustrations, etc.] Too small
(3)’ [Illustrations, etc.] Difficult to follow
• If you have ticked (2), (3) or (3)’, please give us your reasons.

Additional
Comments/
Requests
concerning
This Manual

Please return this questionnaire to : FAX No. : Tokyo 81-3-5484-0454

FUJI PHOTO FILM CO., LTD.
26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.

Printed on Recycled Paper

Ref.No.PP3-A1001E2 TD-04.10-FG Printed in Japan