Scribd
Upload
237 views

Full Wave Bridge Rectifier Circuit (Multisim Simulation)

1. The document describes a full wave bridge rectifier circuit simulated using Multisim. It consists of 4 diodes connected in a bridge structure such that two diodes conduct during each half cycle of the AC input. 2. The simulation circuit includes a 10V, 50Hz AC source, 4 1N4007 diodes, a 100k resistor, and oscilloscope. It converts the AC input to a DC output without negative cycles, achieving an RMS voltage of 6.88V. 3. A 100uF capacitor is added to reduce ripples in the output. In simulation, it smooths the output waveform providing an RMS voltage of 8.26V across the resistor

Uploaded by

Vesagan Messi
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
237 views

Full Wave Bridge Rectifier Circuit (Multisim Simulation)

1. The document describes a full wave bridge rectifier circuit simulated using Multisim. It consists of 4 diodes connected in a bridge structure such that two diodes conduct during each half cycle of the AC input. 2. The simulation circuit includes a 10V, 50Hz AC source, 4 1N4007 diodes, a 100k resistor, and oscilloscope. It converts the AC input to a DC output without negative cycles, achieving an RMS voltage of 6.88V. 3. A 100uF capacitor is added to reduce ripples in the output. In simulation, it smooths the output waveform providing an RMS voltage of 8.26V across the resistor

Uploaded by

Vesagan Messi
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Full wave bridge rectifier circuit [Multisim Simulation]

Email ThisBlogThis!Share to TwitterShare to Facebook

Full wave bridge rectifier circuit [Multisim Simulation].

In one of my previous posts we studied about the half wave rectifier and simulated it using
theNational Instrument’s Multisim Simulation software. In this post, I would like to continue with the
rectifier circuit, by explaining the full wave rectifier.

Basically a rectifier is usually used to rectify the pulses or waveforms of AC to DC. Another name of
Full wave rectifier is Bridge rectifier as is mentioned in the title of this post.

This circuit consists of a set of 4 diodes connected in a bridge like structure. At any instant of time, only 2
diodes will be functional and other 2 will remain idle. In the positive half of the cycle, 2 diodes which are
in forward bias mode will form the circuit and will conduct. In the negative half cycle, other 2 diodes
which were earlier in reverse bias mode will be in forward bias mode and other 2 will be in reverse bias
mode.

Coming to the simulation of this circuit, the circuit diagram drawn using the NI Multisim is shown below:

full wave rectifier circuit diagram

You can see that 4 diodes are connected in a bridge kind of structure and the oscilloscope is connected
across the resistor to observe the voltage waveforms across the resistor.

Here the components used are:

1. Sinusoidal voltage source: 10V, 50Hz


2. 4 diodes: 1N4007
3. Resistor: 100k ohms
4. Oscilloscope

When we run the simulation, only 2 diodes will conduct in each half cycle and will give rise to a voltage
waveform which doesn’t contains any negative half of the original sinusoidal waveform. You can see the
waveforms in the image given below:
full wave rectifier output waveforms

After measuring using a probe, the rms voltage across the resistor is found to be 6.88V. So 10V signal is
converted to 6.88V signal without having any negative cycle. Rest of the voltage i.e. (10-6.88) = 3.12V is
the voltage drop across the diodes. Voltage drop across each diode is 1.56V.

But in practical dc application, we can’t use a DC with such a heavy ripples. So to reduce the ripples, we
can make use of capacitors.

These ripple reducing capacitors are often termed as smoothening capacitor. In the circuit below, you can
see that the electrolytic capacitor of 100uF has been connected in parallel to the resistor. This capacitor
performs charging and discharging operation and converts the full wave rippled output to a smooth DC
output across the resistor. The circuit with a smoothening capacitor is shown below:

full wave rectifier using smoothening capacitor

The value of the capacitor shouldn’t be very small, otherwise it will not be effective in reducing the ripple
to the required extent. Choosing an appropriate value can result in a very smooth DC output. In the image
given below, you can see that 100uF capacitor works perfect with this circuit giving a perfectly smooth DC
output. You can try simulating using a 100nF or other lesser valued capacitor, you will find the ripples
which can be used to study the charging and discharging operations of the capacitor. The output
waveforms are shown below:
output waveform of full wave rectifier using smoothening capacitor

After measurement using a probe, it is found that the rms voltage across the resistor in this case is 8.26V.
Related Post :

You might also like