Preface

Notebook Computer

M980NU

Service Manual

Preface
I
 Preface

Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained
herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent ven-
dor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are
they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.

This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or
reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publica-
tion, except for copies kept by the user for backup purposes.

Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of
their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement
of that product or its manufacturer.
Preface

Version 1.0
June 2009

Trademarks
Intel and Intel Core are trademarks of Intel Corporation.
Windows® is a registered trademark of Microsoft Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective companies.

II
 Preface

About this Manual

This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and
inspection of personal computers.

It is organized to allow you to look up basic information for servicing and/or upgrading components of the M980NU
series notebook PC.

The following information is included:

Chapter 1, Introduction, provides general information about the location of system elements and their specifications.
Chapter 2, Disassembly, provides step-by-step instructions for disassembling parts and subsystems and how to upgrade
elements of the system.

Appendix A, Part Lists

Preface
Appendix B, Schematic Diagrams

III
 Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock and injury to per-
sons when using any electrical equipment:

1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of elec-
trical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter – AC Input 100 - 240V,
50 - 60Hz, DC Output 20V, 11A or 19V, 11.6A).
Preface

This Computer’s Optical Device is a Laser Class 1 Product

IV
 Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer Do not place it on an unstable Do not place anything heavy
to any shock or vibration. surface. on the computer.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This
is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive Do not leave it in a place Don’t use or store the com- Do not place the computer on

Preface
heat or direct sunlight. where foreign matter or mois- puter in a humid environment. any surface which will block
ture may affect the system. the vents.

3. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save
your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power Do not turn off any peripheral Do not disassemble the com- Perform routine maintenance
until you properly shut down devices when the computer is puter by yourself. on your computer.
all programs. on.

V
 Preface

4. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong mag-
netic fields. These can hinder proper performance and damage your data.
5. Take care when using peripheral devices.

Use only approved brands of Unplug the power cord before

peripherals. attaching peripheral devices.

Power Safety
Preface

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.
• Your AC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are
 unsure of your local power specifications, consult your service representative or local power company.
Power Safety • The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do
Warning not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.
Before you undertake • When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.
any upgrade proce- • Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
dures, make sure that • Before cleaning the computer, make sure it is disconnected from any external power supplies.
you have turned off the
power, and discon-
nected all peripherals Do not plug in the power Do not use the power cord if Do not place heavy objects
and cables (including cord if you are wet. it is broken. on the power cord.
telephone lines). It is
advisable to also re-
move your battery in
order to prevent acci-
dentally turning the
machine on.

VI
 Preface

Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the
computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service
personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode
or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.

Battery Guidelines
The following can also apply to any backup batteries you may have.

Preface
• If you do not use the battery for an extended period, then remove the battery from the computer for storage.
• Before removing the battery for storage charge it to 60% - 70%.
• Check stored batteries at least every 3 months and charge them to 60% - 70%.


Battery Disposal
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under var-
ious state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste
officials for details in your area for recycling options or proper disposal.

Caution
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
Discard used battery according to the manufacturer’s instructions.

Battery Level
Click the battery icon in the taskbar to see the current battery level and charge status. A battery that drops below a level of 10%
will not allow the computer to boot up. Make sure that any battery that drops below 10% is recharged within one week.

VII
 Preface

Related Documents
You may also need to consult the following manual for additional information:

User’s Manual on CD
This describes the notebook PC’s features and the procedures for operating the computer and its ROM-based setup pro-
gram. It also describes the installation and operation of the utility programs provided with the notebook PC.
Preface

VIII
 Preface

Contents
Introduction ..............................................1-1 LCD ............................................................................................... A-6
Mainboard ...................................................................................... A-7
Overview .........................................................................................1-1 Blu-Ray Combo ............................................................................. A-8
System Specifications .....................................................................1-2 DVD Super Multi .......................................................................... A-9
External Locator - Top View with LCD Panel Open ......................1-5
External Locator - Front & Right side Views .................................1-6 Schematic Diagrams................................. B-1
External Locator - Left Side & Rear View .....................................1-7 System Block Diagram ...................................................................B-2
External Locator - Bottom View .....................................................1-8 PENRYN 1/2 ..................................................................................B-3
Mainboard Overview - Top (Key Parts) .........................................1-9 PENRYN3 2/2 ................................................................................B-4
Mainboard Overview - Bottom (Key Parts) ..................................1-10 MCP79 FSBI ..................................................................................B-5
Mainboard Overview - Top (Connectors) .....................................1-11 MCP79 MEM CTRL (1) ................................................................B-6
Mainboard Overview - Bottom (Connectors) ...............................1-12 MCP79 MEM CTRL (2) ................................................................B-7
Disassembly ...............................................2-1 MCP79 PCI-E .................................................................................B-8

Preface
MCP79 LAN, Panel ........................................................................B-9
Overview .........................................................................................2-1 MCP79 PCI, LPC .........................................................................B-10
Maintenance Tools ..........................................................................2-2 MCP79 SATA, USB .....................................................................B-11
Connections .....................................................................................2-2
MCP79 HDA, Misc ......................................................................B-12
Maintenance Precautions .................................................................2-3 MCP79 Power ...............................................................................B-13
Disassembly Steps ...........................................................................2-4 MCP79 GND, RMGT PWR, PWRGD .........................................B-14
Removing the Battery ......................................................................2-5
DDR3 SO-DIMM_0 .....................................................................B-15
Removing the Optical (CD/DVD) Device ......................................2-6 DDR SO-DIMM_1 .......................................................................B-16
Removing the Hard Disk Drive .......................................................2-7 Panel, Inverter, TPM .....................................................................B-17
Removing the System Memory (RAM) ..........................................2-9 HDMI, Fan Control ......................................................................B-18
Removing the VGA Card ..............................................................2-11 CRT, DVI .....................................................................................B-19
Installing the VGA Card ...............................................................2-13 ODD, CCD, BT, USB 2.0 .............................................................B-20
Removing the TV Tuner Card .......................................................2-14 KBC ITE IT8512-J .......................................................................B-21
Part Lists ..................................................A-1 PHY RTL8211CL .........................................................................B-22
Part List Illustration Location ........................................................ A-2 Codec, Subwoofer, DMIC ............................................................B-23
Top with Fingerprint ...................................................................... A-3 Audio AMP ...................................................................................B-24
Top without Fingerprint ................................................................. A-4 HDMI Switch ................................................................................B-25
Bottom ............................................................................................ A-5 New Card, Mini Card ...................................................................B-26

IX
 Preface

Card Reader, IEEE 1394 .............................................................. B-27

MXM 3.0 Master .......................................................................... B-28
MXM 3.0 Slave ............................................................................ B-29
MB to Small B’d Connector A ..................................................... B-30
MB to Small B’d Connector B ..................................................... B-31
Power System ............................................................................... B-32
Power VCore ................................................................................ B-33
PWR 1.05V, Screw Hole .............................................................. B-34
Power 1.5V/0.75V ........................................................................ B-35
Power 1.0VS ................................................................................. B-36
Power 3.3V/5V ............................................................................. B-37
Power Charger, DC-In .................................................................. B-38
Single HDD Board ....................................................................... B-39
Dual HDD Board .......................................................................... B-40
Preface

Audio Board ................................................................................. B-41

Power Button Board ..................................................................... B-42
Click & FP Board ......................................................................... B-43
Logo LED Board .......................................................................... B-44
Game Key Board .......................................................................... B-45
TouchPad LED Board .................................................................. B-46
Front R Side LED Board .............................................................. B-47
Front L Side LED Board .............................................................. B-48
Back L Side LED Board ............................................................... B-49
Touch Sensor Board A ................................................................. B-50
Touch Sensor Board B ................................................................. B-51
CIR Board .................................................................................... B-52
Finger Board ................................................................................. B-53
PWR on SEQ Diagram ................................................................. B-54

X
 Introduction

Chapter 1: Introduction
Overview
This manual covers the information you need to service or upgrade the M980NU series notebook computer. Information
about operating the computer (e.g. getting started, and the Setup utility) is in the User’s Manual. Information about driv-
ers (e.g. VGA & audio) is also found in User’s Manual. That manual is shipped with the computer.

Operating systems (e.g. Windows XP, Windows Vista, etc.) have their own manuals as do application software (e.g. word
processing and database programs). If you have questions about those programs, you should consult those manuals.

The M980NU series notebook is designed to be upgradeable. See “Disassembly” on page 2 - 1 for a detailed description

1.Introduction
of the upgrade procedures for each specific component. Please note the warning and safety information indicated by the
“” symbol.

The balance of this chapter reviews the computer’s technical specifications and features.

Overview 1 - 1
 Introduction

System Specifications
Processor Video Adapter

Intel® Core™ 2 Quad Processor - (478-pin) Micro-FC-PGA Package, nVIDIA® GeForce GTX 280M SLI PCIe Video Card
45nm (45 Nanometer) Process Technology: 1GB GDDR3 Video RAM On Board
QX93000 - 2.53 GHz, 12MB On-die L2 Cache & 1066MHz FSB (45W) Supports PCIe * 8 (SLI - 2 * PCIe * 8)
X9100 - 2.53GHz, 6MB On-die L2 Cache & 1066MHz FSB (44W) Supports Microsoft DirectX® 10.0
Q9000 - 2.0GHz, 6MB On-die L2 Cache & 1066MHz FSB (45W) Supports HDCP
Q9100 - 2.26GHz, 12MB On-die L2 Cache & 1066MHz FSB (45W)
BIOS
Intel® Core™ 2 Duo Processor - (478-pin) Micro-FC-PGA Package, One 8Mb Flash ROM
45nm (45 Nanometer) Process Technology: Phoenix™ BIOS
T9400 - 2.53 GHz, 6MB On-die L2 Cache & 1066MHz FSB (35W)
T9600 - 2.80 GHz, 6MB On-die L2 Cache & 1066MHz FSB (35W) Storage
1.Introduction

T9800 - 2.93 GHz, 6MB On-die L2 Cache & 1066MHz FSB (35W)
Up to three (Option) Changeable 2.5" 9.5 mm (h) SATA (Serial) Hard
Disk Drives supporting RAID level 0/1
Intel® Core™ 2 Duo Processor - (478-pin) Micro-FC-PGA Package, One 12.7 mm Super Multi/Blu-Ray Combo/Writer SATA Optical Device
45nm (45 Nanometer) Process Technology: Drive (Option)
P9500 - 2.66 GHz, 6MB On-die L2 Cache & 1066MHz FSB (25W)
P9600 - 2.53 GHz, 6MB On-die L2 Cache & 1066MHz FSB (25W) Keyboard & Pointing Device
P8600 - 2.66 GHz, 3MB On-die L2 Cache & 1066MHz FSB (25W)
Full Size Winkey Keyboard with Numeric Keypad
P8700 - 2.53 GHz, 3MB On-die L2 Cache & 1066MHz FSB (25W)
Built-In TouchPad (Scroll Functionality Included)
Core Logic Eight Touch Sensor Instant Keys (Color, CCD, Bluetooth, WLAN,
Internet, Silent Mode, Sound Effect, Mute)
MCP79 SLI Chipset Eight Gaming Keys G1 ~ G8
Display Card Reader
18.4" Full HD (1920 * 1080) TFT LCD Embedded 7-in-1 Card Reader (MS/ MS Pro/ SD/ Mini SD/ MMC/ RS
MMC/ MS Duo) Note: MS Duo/ Mini SD/ RS MMC Cards require a PC
Memory
adapter
Two 64-bit wide DDRIII (DDR3) data channels
Two 204 Pin SO-DIMM Sockets Supporting DDRIII (DDR3) 1066MHz/
1333MHz Memory Modules
Memory Expandable up to 4GB

1 - 2 System Specifications
 Introduction

Interface Communication

Four USB 2.0 Ports Built-In Giga Base-TX Ethernet LAN

One eSATA Port Bluetooth 2.1 + EDR (Enhanced Data Rate) Module (Factory Option)
One DVI-Out Port (with CRT out) Intel® WiFi Link 5300 Series (3*3 - 802.11a/g/n) Wireless LAN PCIe
One HDMI (High-Definition Multimedia Interface) Port with Audio interface Mini-Card Module (Option)
Output (with HDCP Support) Intel® WiFi Link 5100 Series (1*2 - 802.11a/g/n) Wireless LAN PCIe
One Headphone/Speaker-Out Jack interface Mini-Card Module (Option)
One Microphone-In Jack 3rd Party 802.11b/g Wireless LAN PCIe interface Mini-Card Module
One Line-In Jack (Option)
One S/PDIF Out Jack 2.0M or 3.0M Pixel PC Camera Module with USB interface (Factory
One RJ-45 LAN Jack Option)
One Mini-IEEE1394a Port
Operating System
One DC-In Jack
One Consumer Infrared Port for TV Tuner Remote Controller Windows Vista Home Premium/ Business/ Enterprise/ Ultimate

1.Introduction
CATV Jack (for TV Tuner) Note that the TV Tuner module (factory) option in Windows Vista is
supported by the Windows Media Center software which comes built-
Slots in to the Windows Vista Home Premium and Ultimate Editions only.
One ExpressCard/34/54 Slot Power Management
Two Mini Card Slots:
Slot 1 for PCIe WLAN Module Supports Wake on LAN
Slot 2 for USB TV Tuner Module Supports Wake on USB

Audio Power

High Definition Audio3D Stereo Enhanced Sound System Full Range AC/DC Adapter – AC in 100 - 240V, 50 - 60Hz DC Output
S/PDIF Digital Output 19V, 11.6A or 19V, 12.2A (220 Watts)
Built-In Microphone Easy Changeable Polima Smart Lithium-Ion 4650mAH Main Battery
5 * Built-In Speakers (2W/ 1.5W, 4Ω)
Physical Dimensions & Weight
One Sub Woofer (2W, 4Ω,)
Dolby Surround Supported 439mm (w) * 299mm (d) * 44mm (h)
Around 4.9kg with Battery and ODD
Security

Security (Kensington® Type) Lock Slot

BIOS Password
Fingerprint Reader Module (Factory Option)
Trusted Platform Module V1.2 (Factory Option)

System Specifications 1 - 3
 Introduction

Environmental Spec

Temperature
Operating: 5°C - 35°C
Non-Operating: -20°C - 60°C
Relative Humidity
Operating: 20% - 80%
Non-Operating: 10% - 90%

Optional

Super Multi Drive Module

Blu-Ray Combo Drive Module
Intel® WiFi Link 5300/5100 Series (3*3/1*2 - 802.11a/g/n) Wireless
LAN PCIe Interface Mini-Card Module
1.Introduction

3rd Party 802.11b/g Wireless LAN PCIe Interface Mini-Card Module

Bluetooth 2.1 + EDR (Enhanced Data Rate) Module (Factory Option)
2.0M or 3.0M Pixel USB 2.0 PC Camera Module (Factory Option)
Fingerprint Reader Module (Factory Option)
Mini-Card TV Tuner Module with USB Interface (Factory Option)

1 - 4 System Specifications
 Introduction

External Locator - Top View with LCD Panel Open Figure 1

Top View

1 1. Optional Built-In
PC Camera
2. LCD
3. LED Status
Indicators
4. Touch Sensor
Instant Keys
2 5. 8 * Gaming Keys
6. Keyboard

1.Introduction
7. TouchPad and
Buttons
8. Fingerprint
Reader Module
(optional)
9. LED Power
3 4 Indicators

5 6

External Locator - Top View with LCD Panel Open 1 - 5

 Introduction

Figure 2 External Locator - Front & Right side Views

Front Views
1. Color LEDs
2. Speakers
3. LED Power
Indicators
4. Consumer
Infrared
Transceiver 1 4 1
2 3 2
(enabled with
optional TV Tuner
only)
1.Introduction

Figure 3
Right Side Views
5. Headphone-In
Jack
6. Microphone-In
Jack 13
10
7. Line-In Jack
8. S/PDIF-Out Jack
5 6 7 8 9 11 12
9. Cable (CATV)
Antenna Jack*
10. Combined
eSATA/USB Port
11. USB 2.0 Port
12. Security Lock
Slot
13. Power Button

1 - 6 External Locator - Front & Right side Views

 Introduction

External Locator - Left Side & Rear View

Figure 4
Left Side View
1. DVI-Out Port
2. 2 * USB 2.0 Ports
3. RJ-45 LAN Jack
4. HDMI-Out Port
5. 7-in-1 Card
Reader
5 6 6. ExpressCard Slot
1 3 7
2 4 8 7. Mini-IEEE 1394
Port
8. Optional Device

1.Introduction
Drive Bay

Figure 5
Rear View
9. Color LEDs
9 10 9 10. Speakers
11
11. DC-In Jack

External Locator - Left Side & Rear View 1 - 7

 Introduction

External Locator - Bottom View

Figure 6
Bottom View
1. Sub Woofer
2. Fan Outlet/Intake
3. Component Bay
Cover
4. Battery
(Secondary HDD 1
Bay - HDD3)
5. Primary HDD
1.Introduction

Bay (HDD1 & 2) 2 3 2 2

4
5


Overheating

To prevent your com-

puter from overheating
make sure nothing
blocks the vent/fan in-
takes while the com-
puter is in use.

1 - 8 External Locator - Bottom View

 Introduction

Mainboard Overview - Top (Key Parts) Figure 7

Mainboard Top
Key Parts

1. North Bridge
2. Memory Slots
DDR3 So-DIMM
3. Mini-Card
Connector (WLAN
Module)

1.Introduction
3
2 2

Mainboard Overview - Top (Key Parts) 1 - 9

 Introduction

Figure 8 Mainboard Overview - Bottom (Key Parts)

Mainboard Bottom
Key Parts

1. CPU Socket
2. VGA Socket
3. Mini-Card
Connector (TV
Module) 2 2

1
1.Introduction

6
5
3

1 - 10 Mainboard Overview - Bottom (Key Parts)

 Introduction

Mainboard Overview - Top (Connectors) Figure 9

Mainboard Top
Connectors

1. CCD Cable Connector

2. LCD Cable Connector
3. Side L Cable
Connector
6 4. Inverter Cable
7
1 2 Connector
3 4 5
5. LED Cable Connector
6. Subwoofer Connector
7. Power Button
Connector

1.Introduction
8. Game-Key Cable
Connector
9. Bluetooth Module
8 Connector
10 10. LED Cable Connector
9 11. Touch Pad Connector
16
11 15 17 12. USB Cable Connector
13. Audio Cable
Connector
14. SW Connector
15. Fingerprint Connector
16. Keyboard Cable
Connector
17. Audio Cable
14 Connector
12 13

Mainboard Overview - Top (Connectors) 1 - 11

 Introduction

Figure 10 Mainboard Overview - Bottom (Connectors)

Mainboard Bottom
Connectors

1. Battery
Connector
1.Introduction

2 3 4

1 - 12 Mainboard Overview - Bottom (Connectors)

 Disassembly

Chapter 2: Disassembly
Overview
This chapter provides step-by-step instructions for disassembling the M980NU series notebook’s parts and subsystems.
When it comes to reassembly, reverse the procedures (unless otherwise indicated).

We suggest you completely review any procedure before you take the computer apart.

Procedures such as upgrading/replacing the RAM, optical device and hard disk are included in the User’s Manual but are
repeated here for your convenience.

2.Disassembly
To make the disassembly process easier each section may have a box in the page margin. Information contained under
the figure # will give a synopsis of the sequence of procedures involved in the disassembly procedure. A box with a  
lists the relevant parts you will have after the disassembly process is complete. Note: The parts listed will be for the dis-
Information
assembly procedure listed ONLY, and not any previous disassembly step(s) required. Refer to the part list for the previ-
ous disassembly procedure. The amount of screws you should be left with will be listed here also.

A box with a  will also provide any possible helpful information. A box with a  contains warnings.

An example of these types of boxes are shown in the sidebar. 

Warning

Overview 2 - 1
 Disassembly

NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the
battery is removed too).

Maintenance Tools
The following tools are recommended when working on the notebook PC:

• M3 Philips-head screwdriver
• M2.5 Philips-head screwdriver (magnetized)
• M2 Philips-head screwdriver
• Small flat-head screwdriver
• Pair of needle-nose pliers
• Anti-static wrist-strap
2.Disassembly

Connections
Connections within the computer are one of four types:

Locking collar sockets for ribbon connectors To release these connectors, use a small flat-head screwdriver to
gently pry the locking collar away from its base. When replac-
ing the connection, make sure the connector is oriented in the
same way. The pin1 side is usually not indicated.
Pressure sockets for multi-wire connectors To release this connector type, grasp it at its head and gently
rock it from side to side as you pull it out. Do not pull on the
wires themselves. When replacing the connection, do not try to
force it. The socket only fits one way.
Pressure sockets for ribbon connectors To release these connectors, use a small pair of needle-nose pli-
ers to gently lift the connector away from its socket. When re-
placing the connection, make sure the connector is oriented in
the same way. The pin1 side is usually not indicated.
Board-to-board or multi-pin sockets To separate the boards, gently rock them from side to side as
you pull them apart. If the connection is very tight, use a small
flat-head screwdriver - use just enough force to start.

2 - 2 Overview
 Disassembly

Maintenance Precautions
The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a re- 
moval and/or replacement job, take the following precautions: Power Safety
Warning
1. Don't drop it. Perform your repairs and/or upgrades on a stable surface. If the computer falls, the case and other
Before you undertake
components could be damaged. any upgrade proce-
2. Don't overheat it. Note the proximity of any heating elements. Keep the computer out of direct sunlight. dures, make sure that
3. Avoid interference. Note the proximity of any high capacity transformers, electric motors, and other strong mag- you have turned off the
netic fields. These can hinder proper performance and damage components and/or data. You should also monitor power, and discon-
the position of magnetized tools (i.e. screwdrivers). nected all peripherals
and cables (including
4. Keep it dry. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly telephone lines). It is
damaged. advisable to also re-
5. Be careful with power. Avoid accidental shocks, discharges or explosions. move your battery in

2.Disassembly
•Before removing or servicing any part from the computer, turn the computer off and detach any power supplies. order to prevent acci-
•When you want to unplug the power cord or any cable/wire, be sure to disconnect it by the plug head. Do not pull on the wire. dentally turning the
machine on.
6. Peripherals – Turn off and detach any peripherals.
7. Beware of static discharge. ICs, such as the CPU and main support chips, are vulnerable to static electricity.
Before handling any part in the computer, discharge any static electricity inside the computer. When handling a
printed circuit board, do not use gloves or other materials which allow static electricity buildup. We suggest that
you use an anti-static wrist strap instead.
8. Beware of corrosion. As you perform your job, avoid touching any connector leads. Even the cleanest hands pro-
duce oils which can attract corrosive elements.
9. Keep your work environment clean. Tobacco smoke, dust or other air-born particulate matter is often attracted
to charged surfaces, reducing performance.
10. Keep track of the components. When removing or replacing any part, be careful not to leave small parts, such as
screws, loose inside the computer.

Cleaning
Do not apply cleaner directly to the computer, use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Overview 2 - 3
 Disassembly

Disassembly Steps
The following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM
THE DISASSEMBLY STEPS IN THE ORDER INDICATED.

To remove the Battery:

1. Remove the battery page 2 - 5
To remove the Optical Device:
1. Remove the battery page 2 - 5
2. Remove the Optical device page 2 - 6
To remove the HDD:
2.Disassembly

1. Remove the battery page 2 - 5

2. Remove the HDD page 2 - 7
To remove the System Memory:
1. Remove the battery page 2 - 5
2. Remove the System Memory page 2 - 9
To remove the VGA card:
1. Remove the battery page 2 - 5
2. Remove the VGA card page 2 - 11
To remove the TV Tuner Card:
1. Remove the battery page 2 - 5
2. Remove the TV tuner card page 2 - 14

2 - 4 Disassembly Steps
 Disassembly

Removing the Battery Figure 1

Battery Removal
If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery.
a. Loosen screws.
1. Turn the computer off, and turn it over. b. Release the battery.
2. Loosen screws 1 - 3 and carefully lift the battery 4 up (Figure b) . c. Lift the battery out of the
3. Remove the battery from the battery bay. bay as indicated.

a. c.

2.Disassembly
1 2 3

b. 4

4

4. Battery

• 3 Screws

Removing the Battery 2 - 5

 Disassembly

Figure 2 Removing the Optical (CD/DVD) Device

Optical Device
1. Turn off the computer, and turn it over and remove the battery (page 2 - 5).
Removal
2. Locate the hard disk bay cover and remove screws 1 & 2 , and remove the bay cover 3 .
3. Remove screw 4 .
a. Remove the screws.
b. Remove the cover. 4. Use the screwdriver to push the optical device 6 out of the computer at point 5 .
c. Remove the screw and 5. Reverse the process to install the new device.
push the optical device
out of the computer at
point 8. a. b.
2.Disassembly

1 2

c.

 5 5
3. Hard Disk Bay Cover
6
6. Optical Device 4
• 3 Screws

2 - 6 Removing the Optical (CD/DVD) Device

 Disassembly

Removing the Hard Disk Drive Figure 3

The hard disk drive is mounted in a removable case and can be taken out to accommodate other 2.5" SATA hard disk HDD Assembly
drives with a height of 9.5mm (h). Follow your operating system’s installation instructions, and install all necessary driv- Removal
ers and utilities (as outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk.
a. Remove the screws.
Hard Disk Upgrade Process b. Remove the cover
c. Remove the screws and
1. Turn off the computer, and turn it over and remove the battery (page 2 - 5). lift the hard disk assem-
2. Locate the hard disk bay cover and remove screws 1 & 2 . bly up out off the compu-
3. Remove the bay cover 3 . ter.
4. Remove screws 4 - 9 and pull the tab to disconnect the connector 10 from hard disk assembly. d. Remove the screws and
separate the HDD(s)
5. Lift the hard disk assembly 11 out of the computer. from the connector and
6. Remove screws 12 - 21 (depending on how many hard disks you have installed in the assembly). case.

2.Disassembly
7. Separate the hard disk board connector 22 from the case 23 .
8. Separate the hard disk(s) 24 from the case.
9. Reverse the process to install a new hard disk(s).
a. c. d.
19
4 5 6 18 17
1 16
11
2 12 23

7 8 9
10
13 14
21

b. 22
3. Hard Disk Bay Cover
15 24 11. Hard Disk Assembly
20 22. HDD connector
23. HDD case
24. HDD

3 • 18 Screws

Removing the Hard Disk Drive 2 - 7

 Disassembly

Removing the Hard Disk(s) in the Secondary HDD Bay

Figure 4
Secondary HDD 1. Turn off the computer, and turn it over and remove the battery.
Assembly Removal 2. The secondary hard disk bay is located under the battery compartment.
3. Remove screw 1 - 4 .
a. Remove the screws and 4. Slide the hard disk assembly in the direction of the arrow 5 .
slide the hard disk as- 5. Lift the hard disk assembly 6 out of the compartment.
sembly in the direction of 6. Remove the screws 7 - 10 to release the hard disk from the case 11 .
the arrow. 7. Reverse the process to install any new hard disk(s).
b. Lift the hard disk assem-
bly out off the computer.
c. Remove the screws to re- 10
lease the hard disk from
a. b. c.
the case. 1 2 9
2.Disassembly

11
7
4 3


6. Hard Disk Assembly
11. Hard Disk Case

• 8 Screws

2 - 8 Removing the Hard Disk Drive

 Disassembly

Removing the System Memory (RAM) Figure 5

The computer has two memory sockets for 200 pin Small Outline Dual In-line Memory Modules (SO-DIMM) DDR III RAM Module
Removal
(DDR3) supporting 1066/1333 MHz. The main memory can be expanded up to 6GB. The SO-DIMM modules supported
are 1024MB and 2048MB DDR Modules. The total memory size is automatically detected by the POST routine once a. Remove the screws
you turn on your computer. from the bottom of
the computer.
Memory Upgrade Process b. Turn the computer
1. Turn off the computer, and turn it over and remove the battery (page 2 - 5). over, open the lid/
2. Remove screws 1 & 2 from the bottom of the computer. LCD and lift the LED
3. Turn the computer over, open the Lid/LCD, and carefully (a cable 3 is connected to the underside of the LED cover module.
c. Remove the screws
cover module) lift up the LED cover module 4
from the keyboard.
4. Remove screws 5 - 9 from the keyboard.

2.Disassembly
a. c.

Caution
1 2
5 6 7 8 9
The heat sink, and
CPU area in general,
contains parts which
are subject to high tem-
peratures. Allow the
area time to cool before
removing these parts.
b.

4 
• 7 Screws

Removing the System Memory (RAM) 2 - 9

 Disassembly

5. Carefully lift the keyboard up, being careful not to bend the keyboard ribbon cable.
Figure 6
6. Disconnect the keyboard ribbon cable 10 from the locking collar socket 11 .
RAM Module
7. Remove the keyboard 12 and keyboard shielding plate 13 .
Removal (cont’d.)
d. f. e.
d. Disconnect the cable
from the locking col-
10
lar.
e. Remove the key-
board and keyboard
plate. 11 13
f. Pull the release
latch(es).
g. Remove the mod-
12
ule(s).
2.Disassembly

 8. Gently pull the two release latches 14 & 15 on the sides of the memory socket in the direction indicated by
Contact Warning the arrows (Figure f).
9. The RAM module 16 will pop-up (Figure g), and you can then remove it.
Be careful not to touch
the metal pins on the f. g.
module’s connecting
edge. Even the clean-

est hands have oils 14 15 Single Memory Module
which can attract parti- Installation
cles, and degrade the
module’s performance. 16 If your computer has a single mem-
ory module, then insert the module
into the Channel 0 (JDIMM1)
socket as shown in Figure 6 f.

 10. Pull the latches to release the second module if necessary.

12. Keyboard 11. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot.
13. Keyboard Shield- 12. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket
ing Plate as it will go. DO NOT FORCE the module; it should fit without much pressure.
16. RAM Module(s) 13. Press the module in and down towards the mainboard until the slot levers click into place to secure the module.
14. Replace the heat sink unit, RAM fan, cover and screws.
15. Restart the computer to allow the BIOS to register the new memory configuration as it starts up.

2 - 10 Removing the System Memory (RAM)

 Disassembly

Removing the VGA Card Figure 7

1. Turn off the computer, and turn it over and remove the battery (page 2 - 5). VGA Card Removal
2. Locate the component bay cover and remove screws 1 - 5
3. Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. a. Remove the screws.
b. Remove the cover and
4. Carefully disconnect the fan cable 6 , and remove the bay cover 7 .
disconnect the cable(s).
5. Remove screws 8 - 10 (two video cards are pictured here) from the video card fan(s) and disconnect the fan c. Remove the screws and
cable(s) 11 (if two cards are present). release the VGA card
6. Remove the VGA card fan 12 . fan.

a. c.

2.Disassembly
1 2 4 5 10 10

11
11
8 9 8 9

b.
12 12
7
6


7. Bay Cover
12. VGA card fan

• 11 Screws
VGA Card Fans

Removing the VGA Card 2 - 11

 Disassembly

7. Remove screws 13 - 16 from the heatsink in the order indicated on the label (two video cards are pictured
Figure 8 here).
VGA Card Removal 8. Grip the handle 17 and carefully remove the heatsink 18 .
(cont’d.) 9. Remove screws 19 - 21 from the video card.
10. Carefully remove the VGA card module 22 from the mainboard.
d. Remove the screws.
e. Remove the VGA heat-
sink. d. e.
f. Remove the VGA mod-
ule. 14 16 14 16
18 18

15 13 15 13
2.Disassembly

17 17

f.

22 22 20 21 20 21

19 19


18. VGA Card Heatsink
22. VGA Card Module

• 16 Screws
11. Reverse the process to install a new VGA card modules.

2 - 12 Removing the VGA Card

 Disassembly

Installing the VGA Card

1. Prepare to fit the VGA card 22 into the slot by holding it at about a 30° angle. Figure 9
2. The card needs to be fully into the slot, and the VGA card and socket have a guide-key and pin which align to allow VGA Card
the card to fit securely. Installation
3. Fit the connectors firmly into the socket, straight and evenly.
4. DO NOT attempt to push one end of the card in ahead of the other. a. Carefully Insert the VGA
5. The card’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket Card.
as it will go (none of the gold colored contact should be showing). DO NOT FORCE the card; it should fit without
much pressure.
6. Secure the card with screws 19 - 21 (Figure 8e on page 2 - 12).
7. Place the heatsink 18 back on the card, and secure the screws in the order indicated in Figure 8e on page 2 -
12.
8. Attach the VGA card fan and secure with the screws as indicated in Figure 7 on page 2 - 11.

2.Disassembly
9. Reinsert the component bay cover, and secure with the screws as indicated in Figure 7 on page 2 - 11.

a.

22


22. VGA card Module

Removing the VGA Card 2 - 13

 Disassembly

Figure 10
Removing the TV Tuner Card
TV Tuner Card 1. Turn off the computer, and turn it over, remove the battery (page 2 - 5).
Removal 2. The TV tuner card is visible at point 1 .
3. Remove the screw 2 from the TV tuner module and disconnect the cable 3 .
a. Remove the screws and 4. The TV tuner card 4 will pop-up and and you can remove it.
disconnect the cable. .
b. The TV tuner card will
pop up and remove it.
a. b.

3 2
4 4
2.Disassembly


4. TV tuner card

• 1 Screw

2 - 14 Removing the TV Tuner Card

 Part Lists

Appendix A: Part Lists

This appendix breaks down the M980NU series notebook’s construction into a series of illustrations. The component part
numbers are indicated in the tables opposite the drawings.

Note: This section indicates the manufacturer’s part numbers. Your organization may use a different system, so be sure
to cross-check any relevant documentation.

Note: Some assemblies may have parts in common (especially screws). However, the part lists DO NOT indicate the
total number of duplicated parts used.

Note: Be sure to check any update notices. The parts shown in these illustrations are appropriate for the system at the

A.Part Lists
time of publication. Over the product life, some parts may be improved or re-configured, resulting in new part numbers.

A - 1
 Part Lists

Part List Illustration Location

The following table indicates where to find the appropriate part list illustration.

Table A- 1
Part List Illustration
Location
Parts M980NU

Top with Fingerprint page A - 3

Top without Fingerprint page A - 4

Bottom page A - 5
A.Part Lists

LCD page A - 6

Mainboard page A - 7

Blu-Ray Combo page A - 8

DVD Super Multi page A - 9

A - 2 Part List Illustration Location

 Part Lists

Top with Fingerprint

Figure A - 1
Top with

A.Part Lists
Fingerprint
㾲䈷
╭
╭㾲䈷╭
╭╭
╭╭
╭

㾲䈷

╭
㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭╭
╭╭
╭
╭㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

▁
㦈㪾䇃▂
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭㾲䈷

╭
㓶╭╭
╭䞤㙓╭
╭╭
╭╭
╭╭
▁㾲䈷▂
╭
䠂㖨▓
╭㖃䏧╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

㾲䈷

㾲䈷

╭
╭╭
╭╭
㾲䈷

䂣㛳╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
▁㾲䈷▂

㾲䈷

╭
╭㾲䈷

╭
╭㾲䈷

╭
╭╭
╭㾲䈷

╭
╭╭
╭╭
╭╭
╭╭
╭╭
▁㾲䈷▂
╭
㾲䈷

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

㾲䈷
㾲䈷

㾲䈷

㾲䈷

㾲䈷
㾲䈷

╭
㾲䈷

㾲䈷
㾲䈷

䙾㦴╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭㾲䈷

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭㾲䈷
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

Top with Fingerprint A - 3

 Part Lists

Top without Fingerprint

Figure A - 2
A.Part Lists

Top without
Fingerprint 㾲䈷
╭
╭㾲䈷╭
╭╭
╭╭
╭

㾲䈷

╭
㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭╭
╭╭
╭
╭㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

▁
㦈㪾䇃▂
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

╭
㓶╭╭
╭䞤㙓╭
╭╭
╭╭
╭╭
▁㾲䈷▂
╭
䠂㖨▓
╭㖃䏧╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭

㾲䈷

㾲䈷

╭
╭╭
╭╭
㾲䈷

䂣㛳╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭▁
㾲䈷▂

㾲䈷

╭
╭㾲䈷

╭
╭㾲䈷

╭
╭╭
╭㾲䈷

╭
╭╭
╭╭
╭╭
╭╭
╭╭
▁㾲䈷▂
╭
㾲䈷

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

㾲䈷
㾲䈷

㾲䈷

㾲䈷
㾲䈷

㾲䈷

╭
㾲䈷

㾲䈷
㾲䈷
䙾㦴╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷

A - 4 Top without Fingerprint

 Part Lists

Bottom

Figure A - 3
Bottom

A.Part Lists
㾲䈷

㾲䈷╭
╭╭
╭╭
╭

╭
㓶╭╭
╭╭
╭䞤㙓╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

▁
㦈㪾䇃▂
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

㾲䈷╭
╭╭
╭╭
╭

╭
㾲䈷╭
╭╭
╭╭
╭

╭
╭㾲䈷╭
╭╭
╭╭
╭

㾲䈷

㾲䈷

㾲䈷

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

╭
㓶╭╭
╭╭
╭䞤㙓╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

╭
╭㾲䈷

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

褜㬘╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷

㾲䈷

㦌䁙╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

╭
╭╭
╭㾲䈷

╭
╭╭
╭㾲䈷

㾲䈷

㾲䈷

㾲䈷
╭
㾲䈷

㾲䈷

㾲䈷

㾲䈷

㾲䈷

㾲䈷

Bottom A - 5
 Part Lists

LCD

Figure A - 4
A.Part Lists

LCD

╭
╭╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

╭
㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭
╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭

㕻㢲╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭

▁
㦈㪾䇃▂
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭

╭
㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭褜㬘╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷╭
╭

╭
╭╭
╭褜㬘╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷╭
╭

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭褜㬘╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷╭
╭

㾲䈷╭
╭╭
╭╭
╭
╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭

㾲䈷╭
╭╭
╭╭
╭

A - 6 LCD
 Part Lists

Mainboard

Figure A - 5
Mainboard

A.Part Lists
╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

㾲䈷╭
╭╭
╭╭
╭

╭
╭㾲䈷╭
╭╭
╭╭
╭

╭
╭╭
╭╭
╭㾲䈷╭
╭╭
╭╭
╭

╭
╭㾲䈷╭
╭╭
╭╭
╭

㾲䈷

㾲䈷╭
╭
╭╭╭
╭

㾲䈷╭
╭
╭╭╭
╭

╭
╭
╭╭╭
╭
╭╭╭
╭
╭╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

㾲䈷

╭
╭╭
╭▁
㙲㗺▂
╭╭
╭╭
╭╭
㾲䈷

▁
㙲㗺▂
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷

╭
㯵䀜╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
䧰㞡╭
╭╭
╭╭
╭㾲䈷

╭
╭╭
╭╭
╭㮄䈠╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

╭
㯵䀜╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

╭
╭╭
㮄䈠╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭㾲䈷

㾲䈷

㾲䈷

㾲䈷

㾲䈷

㾲䈷

㾲䈷

╭
㾲䈷

╭
㾲䈷

╭
╭╭
㾲䈷

╭
㾲䈷

╭
╭
㾲䈷

╭
╭
╭╭╭
╭
╭╭╭
╭
╭╭╭
╭
╭╭╭
╭
╭╭╭
╭
╭╭╭
╭
╭╭╭
╭
╭╭╭
╭
╭╭╭
╭
╭㾲䈷
╭
▁㗮䓃㗱㥽▂
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
╭╭
㾲䈷

㾲䈷

㾲䈷

㾲䈷

╭
╭
╭╭㾲䈷╭
╭╭
╭╭
╭

╭
╭
╭╭㾲䈷╭
╭╭
╭╭
╭

╭
╭
╭╭㾲䈷╭
╭╭
╭╭
╭

╭
╭
╭╭㾲䈷╭
╭╭
╭╭
╭

Mainboard A - 7
 Part Lists

Blu-Ray Combo

Figure A - 6
A.Part Lists

Blu-Ray Combo

㾲䈷

㾲䈷

㾲䈷

㕰㖑䜛 㾲䈷

㾲䈷

A - 8 Blu-Ray Combo
 Part Lists

DVD Super Multi

Figure A - 7
DVD Super Multi

A.Part Lists
㾲䈷

㾲䈷

㖑䜛 㾲䈷

㖑䜛 㾲䈷

㾲䈷

㾲䈷

DVD Super Multi A - 9

 Part Lists
A.Part Lists

A - 10
 Schematic Diagrams

Appendix B: Schematic Diagrams

This appendix has circuit diagrams of the M980NU notebook’s PCB’s. The following table indicates where to find the
appropriate schematic diagram.

Diagram - Page Diagram - Page Diagram - Page

Table B - 1
System Block Diagram - Page B - 2 CRT, DVI - Page B - 19 Power 1.0VS - Page B - 36 Schematic
PENRYN 1/2 - Page B - 3 ODD, CCD, BT, USB 2.0 - Page B - 20 Power 3.3V/5V - Page B - 37 Diagrams

B.Schematic Diagrams
PENRYN3 2/2 - Page B - 4 KBC ITE IT8512-J - Page B - 21 Power Charger, DC-In - Page B - 38

MCP79 FSBI - Page B - 5 PHY RTL8211CL - Page B - 22 Single HDD Board - Page B - 39

MCP79 MEM CTRL (1) - Page B - 6 Codec, Subwoofer, DMIC - Page B - 23 Dual HDD Board - Page B - 40

MCP79 MEM CTRL (2) - Page B - 7 Audio AMP - Page B - 24 Audio Board - Page B - 41

MCP79 PCI-E - Page B - 8 HDMI Switch - Page B - 25 Power Button Board - Page B - 42

MCP79 LAN, Panel - Page B - 9 New Card, Mini Card - Page B - 26 Click & FP Board - Page B - 43

MCP79 PCI, LPC - Page B - 10 Card Reader, IEEE 1394 - Page B - 27 Logo LED Board - Page B - 44 
MCP79 SATA, USB - Page B - 11 MXM 3.0 Master - Page B - 28 Game Key Board - Page B - 45 Version Note

MCP79 HDA, Misc - Page B - 12 MXM 3.0 Slave - Page B - 29 TouchPad LED Board - Page B - 46
The schematic dia-
grams in this chapter
MCP79 Power - Page B - 13 MB to Small B’d Connector A - Page B - 30 Front R Side LED Board - Page B - 47 are based upon ver-
sion 6-7P-M980F-002.
MCP79 GND, RMGT PWR, PWRGD - Page B - 14 MB to Small B’d Connector B - Page B - 31 Front L Side LED Board - Page B - 48 If your mainboard (or
other boards) are a lat-
DDR3 SO-DIMM_0 - Page B - 15 Power System - Page B - 32 Back L Side LED Board - Page B - 49 er version, please
check with the Service
DDR SO-DIMM_1 - Page B - 16 Power VCore - Page B - 33 Touch Sensor Board A - Page B - 50
Center for updated di-
agrams (if required).
Panel, Inverter, TPM - Page B - 17 PWR 1.05V, Screw Hole - Page B - 34 Touch Sensor Board B - Page B - 51

HDMI, Fan Control - Page B - 18 Power 1.5V/0.75V - Page B - 35 CIR Board - Page B - 52

B - 1
 Schematic Diagrams

System Block Diagram

B.Schematic Diagrams

Sheet 1 of 53
System Block
Diagram

B - 2 System Block Diagram

 Schematic Diagrams

PENRYN 1/2

Sheet 2 of 53
PENRYN 1/2

B.Schematic Diagrams
PENRYN 1/2 B - 3
 Schematic Diagrams

PENRYN3 2/2
B.Schematic Diagrams

Sheet 3 of 53
PENRYN 2/2

B - 4 PENRYN3 2/2
 Schematic Diagrams

MCP79 FSBI

B.Schematic Diagrams
Sheet 4 of 53
MCP79 FSB

MCP79 FSBI B - 5
 Schematic Diagrams

MCP79 MEM CTRL (1)

B.Schematic Diagrams

Sheet 5 of 53
MCP79 MEM CRTL
(1)

B - 6 MCP79 MEM CTRL (1)

 Schematic Diagrams

MCP79 MEM CTRL (2)

B.Schematic Diagrams
Sheet 6 of 53
MCP79 MEM CRTL
(2)

MCP79 MEM CTRL (2) B - 7

 Schematic Diagrams

MCP79 PCI-E
B.Schematic Diagrams

Sheet 7 of 53
MCP79 PCI-E

B - 8 MCP79 PCI-E
 Schematic Diagrams

MCP79 LAN, Panel

B.Schematic Diagrams
Sheet 8 of 53
MCP79 LAN, Panel

MCP79 LAN, Panel B - 9

 Schematic Diagrams

MCP79 PCI, LPC

B.Schematic Diagrams

Sheet 9 of 53
MCP79 PCI, LPC

B - 10 MCP79 PCI, LPC

 Schematic Diagrams

MCP79 SATA, USB

B.Schematic Diagrams
Sheet 10 of 53
MCP79 SATA, USB

MCP79 SATA, USB B - 11

 Schematic Diagrams

MCP79 HDA, Misc

B.Schematic Diagrams

Sheet 11 of 53
MCP79 HDA, Misc

B - 12 MCP79 HDA, Misc

 Schematic Diagrams

MCP79 Power

B.Schematic Diagrams
Sheet 12 of 53
MCP79 Power

MCP79 Power B - 13
 Schematic Diagrams

MCP79 GND, RMGT PWR, PWRGD

B.Schematic Diagrams

Sheet 13 of 53
MCP79 GND, RMGT
PWR, PWRGD

B - 14 MCP79 GND, RMGT PWR, PWRGD

 Schematic Diagrams

DDR3 SO-DIMM_0

B.Schematic Diagrams
Sheet 14 of 53
DDR3 SO-DIMM_0

DDR3 SO-DIMM_0 B - 15
 Schematic Diagrams

DDR SO-DIMM_1
B.Schematic Diagrams

Sheet 15 of 53
DDR3 SO-DIMM_1

B - 16 DDR SO-DIMM_1
 Schematic Diagrams

Panel, Inverter, TPM

B.Schematic Diagrams
Sheet 16 of 53
Panel, Inverter,
TPM

Panel, Inverter, TPM B - 17

 Schematic Diagrams

HDMI, Fan Control

B.Schematic Diagrams

Sheet 17 of 53
HDMI, Fan Control

B - 18 HDMI, Fan Control

 Schematic Diagrams

CRT, DVI

B.Schematic Diagrams
Sheet 18 of 53
CRT, DVI

CRT, DVI B - 19
 Schematic Diagrams

ODD, CCD, BT, USB 2.0

B.Schematic Diagrams

Sheet 19 of 53
ODD, CCD, BT,
USB 2.0

B - 20 ODD, CCD, BT, USB 2.0

 Schematic Diagrams

KBC ITE IT8512-J

B.Schematic Diagrams
Sheet 20 of 53
KBC ITE IT8512-J

KBC ITE IT8512-J B - 21

 Schematic Diagrams

PHY RTL8211CL
B.Schematic Diagrams

Sheet 21 of 53
PHY RTL8211CL

B - 22 PHY RTL8211CL
 Schematic Diagrams

Codec, Subwoofer, DMIC

B.Schematic Diagrams
Sheet 22 of 53
Codec, Subwoofer,
DMIC

Codec, Subwoofer, DMIC B - 23

 Schematic Diagrams

Audio AMP
B.Schematic Diagrams

Sheet 23 of 53
Audio AMP

B - 24 Audio AMP
 Schematic Diagrams

HDMI Switch

B.Schematic Diagrams
Sheet 24 of 53
HDMI Switch

HDMI Switch B - 25
 Schematic Diagrams

New Card, Mini Card

B.Schematic Diagrams

Sheet 25 of 53
New Card, Mini
Card

B - 26 New Card, Mini Card

 Schematic Diagrams

Card Reader, IEEE 1394

B.Schematic Diagrams
Sheet 26 of 53
Card Reader,
IEEE1394

Card Reader, IEEE 1394 B - 27

 Schematic Diagrams

MXM 3.0 Master

B.Schematic Diagrams

Sheet 27 of 53
MXM 3.0 Master

B - 28 MXM 3.0 Master

 Schematic Diagrams

MXM 3.0 Slave

B.Schematic Diagrams
Sheet 28 of 53
MXM 3.0 Slave

MXM 3.0 Slave B - 29

 Schematic Diagrams

MB to Small B’d Connector A

B.Schematic Diagrams

Sheet 29 of 53
MB to Small B‘d
Connector A

B - 30 MB to Small B’d Connector A

 Schematic Diagrams

MB to Small B’d Connector B

B.Schematic Diagrams
Sheet 30 of 53
MB to Small B‘d
Connector B

MB to Small B’d Connector B B - 31

 Schematic Diagrams

Power System
B.Schematic Diagrams

Sheet 31 of 53
Power System

B - 32 Power System
 Schematic Diagrams

Power VCore

B.Schematic Diagrams
Sheet 32 of 53
Power VCore

Power VCore B - 33
 Schematic Diagrams

PWR 1.05V, Screw Hole

B.Schematic Diagrams

Sheet 33 of 53
PWR 1.05V, Screw
Hole

B - 34 PWR 1.05V, Screw Hole

 Schematic Diagrams

Power 1.5V/0.75V

B.Schematic Diagrams
Sheet 34 of 53
Power 1.5V/0.75V

Power 1.5V/0.75V B - 35
 Schematic Diagrams

Power 1.0VS
B.Schematic Diagrams

Sheet 35 of 53
Power 1.0VS

B - 36 Power 1.0VS
 Schematic Diagrams

Power 3.3V/5V

B.Schematic Diagrams
Sheet 36 of 53
Power 3.3V/5V

Power 3.3V/5V B - 37
 Schematic Diagrams

Power Charger, DC-In

B.Schematic Diagrams

Sheet 37 of 53
Power Charger,
DC-In

B - 38 Power Charger, DC-In

 Schematic Diagrams

Single HDD Board

B.Schematic Diagrams
Sheet 38 of 53
Single HDD Board

Single HDD Board B - 39

 Schematic Diagrams

Dual HDD Board

B.Schematic Diagrams

Sheet 39 of 53
Dual HDD Board

B - 40 Dual HDD Board

 Schematic Diagrams

Audio Board

B.Schematic Diagrams
Sheet 40 of 53
Audio Board

Audio Board B - 41
 Schematic Diagrams

Power Button Board

B.Schematic Diagrams

Sheet 41 of 53
Power Button
Board

B - 42 Power Button Board

 Schematic Diagrams

Click & FP Board

B.Schematic Diagrams
Sheet 42 of 53
Click & FP Board

Click & FP Board B - 43

 Schematic Diagrams

Logo LED Board

B.Schematic Diagrams

Sheet 43 of 53
Logo LED Board

B - 44 Logo LED Board

 Schematic Diagrams

Game Key Board

B.Schematic Diagrams
Sheet 44 of 53
Game Key Board

Game Key Board B - 45

 Schematic Diagrams

TouchPad LED Board

B.Schematic Diagrams

Sheet 45 of 53
TouchPad LED
Board

B - 46 TouchPad LED Board

 Schematic Diagrams

Front R Side LED Board

B.Schematic Diagrams
Sheet 46 of 53
Front R Side LED
Board

Front R Side LED Board B - 47

 Schematic Diagrams

Front L Side LED Board

B.Schematic Diagrams

Sheet 47 of 53
Front L Side LED
Board

B - 48 Front L Side LED Board

 Schematic Diagrams

Back L Side LED Board

B.Schematic Diagrams
Sheet 48 of 53
Back L Side LED
Board

Back L Side LED Board B - 49

 Schematic Diagrams

Touch Sensor Board A

B.Schematic Diagrams

Sheet 49 of 53
Touch Sensor
Board A

B - 50 Touch Sensor Board A

 Schematic Diagrams

Touch Sensor Board B

B.Schematic Diagrams
Sheet 50 of 53
Touch Sensor
Board B

Touch Sensor Board B B - 51

 Schematic Diagrams

CIR Board

CIR BOARD
B.Schematic Diagrams

Sheet 51 of 53
CIR Board

KH_O1 KH_O2 KH_O3

KVDD5
KJ_MB
1 KCIR_RX KGND KGND
2 KVDD5
3
88266-03001
KGND
KR1 KU1
IRM-V038/TR1-P
100_04 KVDD5_CIR

V
V GND2
KC1 KC2 KC3 G GND2
G GND1
0.1U_16V_04 *4.7U_10V_X5R_06 10U_10V_08 O GND1
KGND O
KGND

KGND
KCIR_RX

B - 52 CIR Board
 Schematic Diagrams

Finger Board

B.Schematic Diagrams
Sheet 52 of 53
Finger Board

Finger Board B - 53
 Schematic Diagrams

PWR on SEQ Diagram

B.Schematic Diagrams

Sheet 53 of 53
PWR on SEQ
Diagram

B - 54 PWR on SEQ Diagram