JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.

Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road

36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 1/12

JUMO Quantrol LC100/LC200/LC300

Universal PID Controller Series

LC100 (702031)
Brief description
The Quantrol series is available in the three DIN formats 48 mm x 48 mm, 48 mm x 96 mm, and
96 mm x 96 mm. It is used for two-state and three-state control applications as well as for the
control of regulating valves or SCR power controllers via a continuous controller output.
The universal analog input for RTD temperature probes, thermocouples, or current/voltage sig-
nals is user programmable. The setpoint value, the actual value, and all parameters are dis-
played on two seven-segment LED displays (red/green) with one or two decimal place(s). The
values can be displayed in °C or °F. Depending on the format, up to five relay outputs with a
switching capacity of 3 A / 230 V or up to four logic outputs 0/14 V are available. The switch po-
sition of the relays or logic outputs is displayed using yellow LEDs. Different functions can be as-
signed to these outputs. An analog output 0 to 10 V or 0(4) to 20 mA is configurable as
continuous controller output, actual value output, or setpoint value output. Using the binary input,
the device settings and operation can be locked, a ramp or the timer can be activated, or self- LC200 (702032)
optimization can be initiated. The supply voltage is optionally AC 110 to 240 V or AC/DC
20 to 30 V.
The controller has a ramp function with adjustable gradient for constant setpoint change. In ad-
dition, a special firing curve for small pottery kilns can be used which allows controlled starting
and time dependent firing. The user can enter setpoint values, gradient, and firing time directly
at the device.
The device can be connected to host systems or devices using the RS485 serial interface. In-
stead of operating the device from the front, the user can also program the controller using the
setup program and USB interface; this requires no additional voltage supply for the controller.
The Quantrol series, like all JUMO controllers, is also equipped with reliable JUMO self-optimi-
zation (autotuning).

LC300 (702034)

Block diagram Special features

• 48 × 48, 48 × 96, 96 × 96 mm formats
Analog input LC100 Relay (N/O contact)
• Two-state/three-state and continuous con-
LC200 troller
LC300
Binary input Option 1 • Sensor monitoring
• Up to 5 outputs
Option 2 • Self-optimization (autotuning) for exact PID
control
• Manual/automatic mode
Option 3* • Configurable limit value monitoring (alarms)
• Setpoint changeover
Setup interface Option 4* • Level inhibit and key lock
* Option for LC200/LC300 • RS485 interface (Modbus RTU)
Options are delivered ex-factory acc. to the order details. • Ramp and timer function
• Firing curve for pottery kilns
Option 1 Option 2 Option 3 Option 4 • Push-in controller insert
X X X X Relay output (N/O contact) • Setup interface (USB Mini-B)
X X X X Logic output
X Analog output
X RS485 interface

Approvals/approval marks (see "Technical data")

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 2/12

Description Timer
The timer is started manually or automatically
(after power on, for example). When the timer
Self-optimization (autotuning) expires, the timer output signal changes its
Standard features include the tried and tested state (configurable). The timer can be used to
self-optimization (oscillation method), which implement functions like time-limited control or
makes it possible for the controller to be setpoint changeover.
matched to the control loop by a user who is
not a control technology expert. Here, the re- Setup program
action of the control path to the specific vari- The setup program provides the user with an
able changes is evaluated and the controller easy and comfortable way to configure the
parameters proportional band, reset time, de- controller using a PC.
rivative time, cycle time, and filter time con-
stant are calculated. The PC has to be connected to the controllers
USB interface (Mini-B type) with a USB cable.
Ramp function Thereby the controller is powered over the
USB interface. As a result, no mains supply is
The ramp function is used for a constant required during the configuration.
change of setpoint value w up to the ramp limit
value SP (entered setpoint value). A rising or
a falling edge arises depending on the actual
value at the time of ramp start t0. The slope is
defined by a gradient which is entered during
the controller configuration.

Firing curve
The firing curve is used for controlled starting
and time-dependent firing of small pottery
kilns. The user can enter setpoint values, gra-
dient, and firing time directly at the device.

°C
Setpoint value

Actual value

Limit value monitoring

The controller is equipped with two limit value
monitoring functions, each with eight configu-
rable alarm functions. Any analog signals can
be selected as actual and setpoint value from
a selector. When a limit value is exceeded, a
signal can be displayed or an internal control-
ler function initiated. With the limit value mon-
itoring, extensive alarm and limit value
functions can be implemented.

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 3/12

Controller parameters
All the parameters and their meanings are included in the table. Some parameters may be missing or meaningless for a particular type of controller.

Parameters Value range Factory setting Meaning

Proportional band 1 (Pb1) 0 to 9999 digit 0 digit Size of the proportional band
Proportional band 2 (Pb2) 0 to 9999 digit 0 digit The controller structure is not effective with Pb = 0 (behavior identical
to limit value monitoring). For a continuous controller, Pb1 must be > 0.
Derivative time (dt) 0 to 9999 s 80 s Influences the differential component of the controller output signal
Reset time (rt) 0 to 9999 s 350 s Influences the integral component of the controller output signal
Cycle time 1 (Cy1) 0 to 999.9 s 20.0 s When using a switched output, the cycle time should be chosen so that
Cycle time 2 (Cy2) 0.0 to 999.9 s 20.0 sec the energy supply to the process is as continuous as possible without
overloading the switching elements.
Contact spacing (db) 0.0 to 999.9 digit 0.0 digit Spacing between the two control contacts of the three-state controller
Switching differential 1 (HyS1) 0.0 to 999.9 digit 1.0 digit Switching differential of a switching controller with proportional band
Switching differential 2 (HyS2) 0.0 to 999.9 digit 1.0 digit Pb = 0 (behavior identical to limit value monitoring)
Working point (y0) -100 to +100 % 0% Output level for P and PD controller (if x = w then y = y0)
Output value limit 1 (y1) 0 to 100 % 100 % Maximum output value limit (only effective if Pb > 0)
Output value limit 2 (y2) -100 to +100 % -100 % Minimum output value limit (only effective if Pb > 0)

Technical data
Thermocouple input
Description Standard Measuring rangea Measuring accuracyb Ambient temperature
influence
Fe-CuNi "L" -150 to +900 °C ≤ 0.4 % ≤ 100 ppm/K
Fe-CuNi "J" EN 60584 -200 to +1200 °C ≤ 0.4 % ≤ 100 ppm/K
Cu-CuNi "T" EN 60584 -200 to +400 °C ≤ 0.4 % ≤ 100 ppm/K
NiCr-Ni "K" EN 60584 -200 to +1372 °C ≤ 0.4 % ≤ 100 ppm/K
NiCr-CuNi "E" EN 60584 -200 to +1000 °C ≤ 0.4 % ≤ 100 ppm/K
NiCrSi-NiSi "N" EN 60584 -100 to +1300 °C ≤ 0.4 % ≤ 100 ppm/K
Pt10Rh-Pt "S" EN 60584 -40 to +1768 °C ≤ 0.4 % ≤ 100 ppm/K
Pt13Rh-Pt "R" EN 60584 -40 to +1768 °C ≤ 0.4 % ≤ 100 ppm/K
Cold junction: KTY internal
a
This information refers to the ambient temperature of 20 °C.
b
Incl. measuring accuracy at the cold junction.
The accuracy values refer to the measuring range.

RTD temperature probe input

Designation, Measuring range Measuring accuracya Ambient temperature
connection type influence
Pt100 EN 60751 -200 to +650 °C ≤ 50 ppm/K
2-wire connection ≤ 0.4 %
3-wire connection ≤ 0.4 %
Pt1000 EN 60751 -200 to +650 °C ≤ 50 ppm/K
2-wire connection ≤ 0.4 %
3-wire connection ≤ 0.4 %
KTY, R25 = 1000 Ω -50 to +150 °C ≤ 50 ppm/K
2-wire connection ≤ 1.0 %
KTY, R25 = 2000 Ω -50 to +80 °C ≤ 50 ppm/K
2-wire connection ≤ 1.0 %
Cu-50 -50 to +200 °C ≤ 50 ppm/K
3-wire connection ≤ 1.0 %

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 4/12

Designation, Measuring range Measuring accuracya Ambient temperature

connection type influence
Probe wire resistance: max. 30 Ω per wire with 3-wire circuit
Measuring current: Pt100 approx. 1 mA; Pt1000 and KTY approx. 100 μA
Lead compensation: not required for 3-wire circuit. For a 2-wire circuit, the lead resistance can be compensated by correcting the actual value.
a
The accuracy values refer to the measuring range.

Input for standard signals

Measuring range Measuring accuracya Ambient temperature influence
Voltage 0 to 10 V ≤ 0.4 % ≤ 150 ppm/K
Input resistance > 650 kΩ
Current 0(4) to 20 mA ≤ 0.4 % ≤ 100 ppm/K
Voltage drop > 2.2 V
a The accuracy values refer to the maximum measuring range.

Binary input
Input for potential-free contact Open = inactive;
Closed = active

Measuring circuit monitoring

In the event of a malfunction, the outputs move to a defined (configurable) status.

Measuring probe Overrange/underrange Probe/cable short circuit Probe/cable break

Thermocouple • - •
RTD temperature probe • • •
Voltage 0 to 10V - - -
Current 4 to 20 mA • • •
Current 0 to 20 mA - - -
• = detected - = not detected

Outputs
Relay (N/O contact)
Contact rating Max. 3 A at 230 V AC resistive load
Contact life 150,000 operations at nominal load
350,000 operations at 1
310,000 operations at 1 A and cosϕ > 0.7
Logic output 0/14V / 20mA max.
Voltage (option)
Output signal 0 to 10V
Load resistance > 600 Ω
Accuracy < 0.5 %
Current (option)
Output signals 0 to 20 mA / 4 to 20 mA
Load resistance < 450 Ω
Accuracy < 0.5 %

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 5/12

Controller
Controller type Two-state controller, three-state controller, continuous controller
Controller structures P/PI/PD/PID
Sampling rate 250 ms
A/D converter 16-bit resolution

Timer
Accuracy 0.8 % ± 10 ppm/K ± 250 ms

Electrical data
Voltage supply (switch mode PSU) AC 110 to 240V +10/-15 %, 48 to 63Hz
AC/DC 20 to 30V, 48 to 63Hz
Electrical security Acc. to DIN EN 61010, part 1; overvoltage category III, pollution degree 2
Power consumption Max. 14 VA
Electrical connection On the rear via screw terminals; with core-end ferrule of a pipe shape, open cable lug or pin cable lug
Conductor cross section Fine-strand 0.25 to 1.5 mm2
Tightening torque 0.5 Nm
Electromagnetic compatibility Acc. to DIN EN 61326-1
Interference emission Class A - only for industrial use -
Interference immunity Industrial requirements
Setup interface USB socket, type Mini-B 5-pole

Requirements for core-end ferrules and cable lugs

Core-end ferrule Pipe shape, without plastic sheath acc. to DIN 46228 part 1,
with plastic sheath acc. to DIN 46228 part 4
Cable lug Open crimp cable lug, dimensionally adapted to DIN 46237 for closed crimp cable lugs
Pin cable lug Acc. to DIN 46231
For UL applications Use of the cable lugs or ferrules acc. to UL 486A-B (UL listed or recognized)

Case and ambient conditions

Case type Plastic case for panel mounting acc to. IEC 61554 (indoor use)
Dimensions (front) LC100: 48 mm x 48 mm; LC200: 48 mm x 96 mm (portrait format);
LC300: 96 mm x 96 mm
Weight (fully fitted) LC100: approx. 150 g; LC200: approx. 200 g; LC300: approx. 300 g
Protection class Acc. to DIN EN 60529, at the front IP 65, at the rear IP 20
Operating position Any
Panel cut-out LC100: 45 mm x 45 mm; LC200: 45 mm x 92 mm;
LC300: 92 mm x 92 mm
Minimum spacing horizontal/vertical LC100: 11 mm / 30 mm (65 mm with USB cable);
LC200/LC300: 22 mm / 30 mm (65 mm with USB cable)
Depth behind panel LC100: max. 95 mm; LC200/LC300: max. 80 mm
Ambient/storage temperature range -5 to +55 °C / -40 to +70 °C
Climatic conditions Rel. humidity < 90 % annual average, without condensation
Site altitude Up to 2000 m above sea level

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 6/12

Interface
Interface type RS485
Protocol Modbus RTU
Baud rate 9600, 19200
Data format 8 data bits, no parity bit, 1 stop bit
Device address 0 to 254
No. of subscribers Max. 32

7-segment displays
Digit height
LC100, LC200 Upper display: 10 mm; lower display: 7 mm
LC300 Upper display: 20 mm; lower display: 13 mm
Color Upper display: red; lower display: green
Places 4 (including decimal places)
Decimal places 0, 1, 2 (configurable)
Display range -1999 to 9999

Approvals/approval marks
Approval mark Testing agency Certificate/certification Inspection basis Valid for
number
c UL us Underwriters Laboratories E201387 UL 61010-1, all versions
CAN/CSA C22.2
No. 61010-1

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 7/12

Dimensions
LC100

+0.6
+0.6
45
45

(1)

(2)

(1) Setup interface (USB) (2) Panel cut-out

on the device top

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 8/12

LC200

(1)

+0.8
45
+0.8
92

(2)

(1) Setup interface (USB) (2) Panel cut-out

on the device bottom

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 9/12

LC300

(1)

+0.8
+0.8
92

92
(2)

(1) Setup interface (USB) (2) Panel cut-out

on the device bottom

Minimum spacing of panel cut-outs

Type Without USB cable With USB cable
Horizontal Vertical Horizontal Vertical
LC100 11 mm 30 mm 11 mm 65 mm
LC200 22 mm 30 mm 22 mm 65 mm
LC300 22 mm 30 mm 22 mm 65 mm

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 10/12

Display and control elements

(A) Programming / one level deeper
(B) Value reduction / previous parameter
(C) Value increase / next parameter
(E) (D) Function key / leave level
(E) Red 7-segment display (factory-set: actual value);
(G) 4-digit, configurable decimal place (automatic adjustment on display over-
(F) flow)
(H) (F) Green 7-segment display (factory-set: setpoint value); 4-digit, configurable
decimal place; also display of level and parameter symbols
(G) LED 1 to 3(5): switching position of binary output (LED is lit = output active)
(H) LED ramp function or firing curve

(A) (B) (C) (D)

The software version is displayed on the device when

simultaneously pressing keys (A) and (C).

Electrical isolation
(1) Analog input
(2) Binary input
(3) (2) (1)
(3) Setup interface (USB)
(4) (4) Voltage supply
30 V AC 30 V AC 2300 V (5) RS485 interface
2300 V 50 V DC 50 V DC AC (6) Analog output
AC
(5) (6) (7) (8) (7) Relay outputs
(8) Logic outputs

Connection diagram
The connection diagram in the data sheet provides preliminary information about the connection possibilities. For the electrical connection only
use the brief instructions or the operating manual. The knowledge and the correct technical execution of the safety information/instructions con-
tained in these documents are mandatory for installation, electrical connection, and startup as well as for safety during operation.
The terminal strips on the device rear are equipped with screw terminals. Please refer to the technical data for specifications concerning the con-
ductor cross section.

LC100 LC200 LC300

L1(L+) 12 L1(L+) 12
N(L-) 13 N(L-) 13

4 14 4 14
5 15 5 15
USB
12 L1(L+) 7 16 7 16
11 13 14 N(L-) 8 17 8 17
10 9 9
9 7 6 4 10 18 10 18
8 5 11 19 11 19
USB USB

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 11/12

Connection Symbol LC100 LC200/LC300

Analog input
Thermocouple + 9 10

- 8 11
RTD temperature probe, 2-wire 10 9

8 11
RTD temperature probe, 3-wire 10 9

9 10

8 11
Voltage + 12 7
DC 0 to 10 V Ux
(usable alternatively to binary input) 11 8
-
Current + 9 10
DC 0(4) to 20 mA Ix
- 8 11
Binary input 11 7
for potential-free contact
(usable alternatively to analog input DC 0 to10 V) 12 8
Output: 1 2 3 1 2 3 4 5
Analog output + 13 12
DC 0 to 10 V, DC 0(4) to 20 mA Ux, Ix
- 14 13
Relay output (N/O contact) 4 13 6 4 12 14 16 18
(max. 3 A at AC 230 V, resistive load)
5 14 7 5 13 15 17 19
Logic output (DC 0/14 V) + 13 7 12 14 16 18
Ux
- 14 6 13 15 17 19
RS485 interface + 7 14
RxD/TxD
- 6 15
Output 1 as standard; outputs 2 to 5 optional (options 1 to 4)
Voltage supply L1 (L+) L1 (L+)
AC/DC
N (L-) N (L-)
Setup interface USB socket, type Mini-B 5-pole

2013-09-23/00600565
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road
36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM20 2DY, UK Phone: 315-437-5866
Phone: +49 661 6003-0 Phone: +44 1279 635533 1-800-554-5866
Fax: +49 661 6003-607 Fax: +44 1279 635262 Fax: 315-437-5860
E-mail: [email protected] E-mail: [email protected] E-mail: [email protected]
Internet: www.jumo.net Internet: www.jumo.co.uk Internet: www.jumousa.com

Data Sheet 702030 Page 12/12

Order details
(1) Basic type
702031 Quantrol LC100 (format 48 mm x 48 mm) 1x analog input (universal), 1x binary inputa, 1x relay
output (N/O contact)
702032 Quantrol LC200 (format 48 mm x 96 mm, portrait format) 1x analog input (universal), 1x binary
inputa, 1x relay output (N/O contact)
702034 Quantrol LC300 (format 96 mm x 96 mm) 1x analog input (universal), 1x binary inputa, 1x relay
output (N/O contact)
(2) Version
X X X 8 Standard with factory settings
X X X 9 Customer-specific configuration (specifications in plain text)
(3) Option for expansion slot 1
X X X 0 Not used
X X X 1 1 relay output (N/O contact)
X X X 2 1 logic output
X X X 3 1 analog output (configurable)
(4) Option for expansion slot 2
X X X 0 Not used
X X X 1 1 relay output (N/O contact)
X X X 2 1 logic output
X X X 4 1 RS485 interface
(5) Option for expansion slot 3
X X X 0 Not used
X X 1 1 relay output (N/O contact)
X X 2 1 logic output
(6) Option for expansion slot 4
X X X 0 Not used
X X 1 1 relay output (N/O contact)
X X 2 1 logic output
(7) Voltage supply
X X X 23 AC 110 to 240 V +10/-15 %, 48 to 63 Hz
X X X 25 AC/DC 20 to 30 V, 48 to 63 Hz
a
Binary input for potential-free contact (usable alternatively to analog input DC 0 to 10 V).

(1) (2) (3) (4) (5) (6) (7)

Order code / - -
Order example 702034 / 8 - 3 4 1 2 - 23

Scope of delivery
1 controller in the ordered version (including seal and fastening elements)
1 Brief Instructions B 702030.7 in DIN A6 format (multilingual)

Accessories
Description Part no.
USB cable, A-connector to Mini-B-connector, length 3 m 00506252

2013-09-23/00600565