PRT3 Printer Module:

ASCII Protocol Programming Instructions

We hope this product performs to your complete satisfaction. Should you have any
questions or comments, please visit www.paradox.com and send us your comments.
Table of Contents
Technical Specifications ............................................ 1 Request Area Label ................................................. 14
Panel Specifications .................................................. 1 Request User Label ................................................. 14
Installation ................................................................. 3 Area Arm ................................................................. 14
Overview ................................................................... 3 Area Quick Arm ....................................................... 14
Programming Sections .............................................. 3 Area Disarm ............................................................. 15
Serial Port Setup ....................................................... 4 Emergency Panic .................................................... 15
Virtual Input Programming ......................................... 4 Medical Panic .......................................................... 15
Virtual PGM Programming ........................................ 7 Fire Panic ................................................................ 16
ASCII Protocol ......................................................... 12 Smoke Reset ........................................................... 16
Printer Module to Digiplex Panel Utility Key ................................................................. 16
Communication Status ......................................... 12 Commands sent from the Printer Module
Commands sent to the Printer Module to the Home Automation Module .......................... 16
from the Home Automation Module ...................... 12 Virtual PGM Events ................................................. 16
Virtual Input Open ................................................... 12 System Events ......................................................... 17
Virtual Input Closed ................................................. 12 PGM Activation Event .............................................. 23
Request Area Status ............................................... 13 PGM Deactivation Option ........................................ 23
Request Zone Status ............................................... 13 PGM Deactivation Event ......................................... 23
Request Zone Label ................................................ 13 PGM Programming Table ........................................ 23

Technical Specifications
Parallel Port: Minimum 80 column printer
Serial Port: 1 start bit, 8 data bit, no parity and 1 stop bit (8N1)
Input Voltage: 9 -16 Vdc
Current Consumption: 60mA maximum
Serial Port Baud Rates: 2400, 9600, 19200 or 57600 bps
Event Buffer: 2048 events
Compatibility: Digiplex EVO48, EVO96, EVO192 control panels
DGP-848 control panel (V4.11 and up)
DGP-NE96 control panel (V1.60 and up)

Panel Specifications
Feature EVO48 EVO96 EVO192 DGP-848 DGP-NE96
Zones 48 96 192 48 96
Users 96 999 999 96 999
Areas 4 8 8 4 8

1
Introduction
The PRT3 Printer Module can be used as an interface between a home automation module and your Digiplex system. When in home
automation mode, the Printer Module can receive and send commands to and from the home automation module and the Digiplex control
panel, linking your home automation capabilities with your security system.

The Printer Module features 16 onboard virtual inputs. These inputs are not related to any physical input on the module, but operate in the
same manner and are programmed in the same way as traditional zone inputs. A virtual input can be programmed to trigger a response
from the Digiplex control panel based on an event that has occurred within the home automation module. For example, your home
automation module may consist of a temperature sensor which you could associate with a virtual input. If the temperature fell to a certain
level, the home automation module would send a command to open/close one of the Printer Module’s virtual inputs and could trigger a
Digiplex zone programmed with a 24-hr. freeze to generate an alarm. Using virtual inputs to trigger events within the Digiplex control panel
involves associating the Printer Module’s virtual input to a zone or a keyswitch on the control panel. See “Virtual Input Programming” on
page 4.

The Printer Module also features 30 virtual PGMs for use with its home automation interface capabilities. These PGMs are not related to any
physical output on the module, but operate in the same manner and are programmed in the same way as a traditional PGM. A virtual PGM
can be used to trigger a response within the home automation module based on an event that has occurred within the Digiplex system. For
example, when a user uses the Digiplex system to disarm an area, this event could activate a virtual PGM on the Printer Module and trigger
a response within the home automation system, such as turning on a specific light on the premises. See “Virtual PGM Programming” on
page 7.

In order for the home automation module and the Digiplex control panel to communicate through the Printer Module, the home automation
module must be programmed to communicate using the ASCII Protocol. See “ASCII Protocol” on page 12.

For a complete list of the Printer Module’s event reporting features, see the Printer Module V1.0 (PRT3) Instructions.

2
Installation
The Printer Module is connected to the control panel’s combus. Connect the four terminals labeled red, black, green, and yellow of the
module to the corresponding terminals on the control panel as shown in Figure 2 on page 22. See the EVO or DGP-848 Reference &
Installation Manual for the maximum allowable installation distance from the control panel.

The home automation module must be connected directly to the Printer Module’s serial port (9-pin/ DB-9 connector). See Figure 2 on page
22 for an overview of the Printer Module’s connections, LEDs and connectors.

Overview
The following provides of an overview of how the Printer Module communicates with the home automation system.

Figure 1: Typical ASCII Application

• Virtual PGM events • ASCII commands

• System events (arm, disarm, panic, virtual
• Communication with input open/close)
panel status

Programming Sections
The following describes the programming sections which must be set when the Printer Module acts as an interface between a control panel
and a home automation module using the ASCII Protocol.

To access the Printer Module’s programming mode:

STEP 1: Press and hold the [0] key.

STEP 2: Enter the [INSTALLER CODE].
STEP 3: Enter section [953] (DGP-848) / [4003] (EVO).
STEP 4: Enter the Printer Module’s 8-digit [SERIAL NUMBER].
STEP 5: Enter the 3-digit [SECTION] you want to program.
STEP 6: Enter the required data.

The Printer Module can also be programmed using the WinLoad Security Software (V2.62 or higher) or using the control panel’s Module
Broadcast feature. Refer to the panel’s Reference & Installation Manual for more details. Please note that the serial number can be located
on the Printer Module’s PC board.

3
Serial Port Setup
The following list the serial port programming options which must be set in order for the Printer Module to communicate with the home
automation module.

Section [016] - Option [1]

Enable Serial Port
When this option is ON (enabled), you can connect the home automation module directly to the Printer Module’s 9-pin serial or USB port.
Set option [4] to ON when using the Printer Module as an interface between a home automation module and the Digiplex system.

Section [016] - Options [2] & [3]

Baud Settings
This option allows you to set the Printer Module’s serial port baud rate. Set the Printer Module’s baud rate
to match that of the home automation module. Refer to the home automation module’s documentation to
determine what baud rate to set the Printer Module to.

U = default setting

Section [016] - Option [4]

Serial Port Usage
This option allows you to set the Printer Module’s serial port usage to either Event Reporting or Home Automation. To set the Printer Module
to Home Automation mode, set option [4] to ON .

Section [016] - Options [5] & [6]

Home Automation Options
This option allows you to select the home automation protocol for the Printer Module. To select
the ASCII Protocol, set options [5] and [6] to OFF .

U = default setting

For more information on the Clipsal C-Bus Protocol, see the C-Bus Programming Instructions on our website at paradox.com.

Virtual Input Programming

The home automation module can be programmed to open/close the Printer Module’s virtual inputs and generate activity within the Digiplex
system. The tables below offer an example of the virtual input programming sections which must be set for Virtual Input 1.

Section [700] : Virtual Input Options

Option OFF ON
[1] Enabling Virtual Input U Disabled N Enabled

[3] and [4] Virtual Input Close

[5] Virtual Input Base Time Selection U Seconds N Minutes

4
 Section Data Description Default

[701] __/__/__ (000 to 255) x Base Time Virtual Input 1 Timer 005

Refer to the table below for a list of the programming sections for all virtual inputs.

Virtual Virtual Virtual Virtual

Section Section Section Section
Input Input Input Input
1 [700] & [701] 5 [740] & [741] 9 [780] & [781] 13 [820] & [821]
2 [710] & [711] 6 [750] & [751] 10 [790] & [791] 14 [830] & [831]
3 [720] & [721] 7 [760] & [761] 11 [800] & [801] 15 [840] & [841]
4 [730] & [731] 8 [770] & [771] 12 [810] & [811] 16 [850] & [851]

The following describes the programming sections and options specific to the Printer Module’s virtual inputs. Use the programming tables to
document specific settings for all programmed virtual inputs.

Section [700] - Option [1]

Enabling Virtual Input Option
Each virtual input must be individually enabled. To enable the virtual input, set option [1] to ON.
U = default setting
Virtual Virtual
Section [1] OFF [1] ON Section [1] OFF [1] ON
Input Input
[700] 1 U disabled N enabled [780] 9 U disabled N enabled
[710] 2 U disabled N enabled [790] 10 U disabled N enabled
[720] 3 U disabled N enabled [800] 11 U disabled N enabled
[730] 4 U disabled N enabled [810] 12 U disabled N enabled
[740] 5 U disabled N enabled [820] 13 U disabled N enabled
[750] 6 U disabled N enabled [830] 14 U disabled N enabled
[760] 7 U disabled N enabled [840] 15 U disabled N enabled
[770] 8 U disabled N enabled [850] 16 U disabled N enabled

Section [700] - Options [3] and [4]

Virtual Input Close Option
The virtual input can be closed by receiving a virtual input close command and/or after a timer
elapses. This option determines how the virtual input will close.

U = default setting
Section Virtual Input [3] OFF / [4] OFF [3] ON / [4] OFF [3] OFF / [4] ON
[700] 1 U close command N virtual input timer N close command or virtual input timer
[710] 2 U close command N virtual input timer N close command or virtual input timer
[720] 3 U close command N virtual input timer N close command or virtual input timer
[730] 4 U close command N virtual input timer N close command or virtual input timer
[740] 5 U close command N virtual input timer N close command or virtual input timer
[750] 6 U close command N virtual input timer N close command or virtual input timer
[760] 7 U close command N virtual input timer N close command or virtual input timer
[770] 8 U close command N virtual input timer N close command or virtual input timer
[780] 9 U close command N virtual input timer N close command or virtual input timer

5
 [790] 10 U close command N virtual input timer N close command or virtual input timer
[800] 11 U close command N virtual input timer N close command or virtual input timer
[810] 12 U close command N virtual input timer N close command or virtual input timer
[820] 13 U close command N virtual input timer N close command or virtual input timer
[830] 14 U close command N virtual input timer N close command or virtual input timer
[840] 15 U close command N virtual input timer N close command or virtual input timer
[850] 16 U close command N virtual input timer N close command or virtual input timer

Section [701]
Virtual Input Timers
If the virtual input is set to follow its Virtual Input Timer, the entered value represents the amount of time that the virtual input will remain
open. To program the Virtual Input Timer, enter a 3-digit value from 000 to 255. Depending on the Virtual Input Base Time (see below), the
Virtual Input Timer will either be in seconds or minutes.

Section Virtual Input Data Section Virtual Input Data

[701] 1 __/__/__ (000 to 255) x Base time [781] 9 __/__/__ (000 to 255) x Base time
[711] 2 __/__/__ (000 to 255) x Base time [791] 10 __/__/__ (000 to 255) x Base time
[721] 3 __/__/__ (000 to 255) x Base time [801] 11 __/__/__ (000 to 255) x Base time
[731] 4 __/__/__ (000 to 255) x Base time [811] 12 __/__/__ (000 to 255) x Base time
[741] 5 __/__/__ (000 to 255) x Base time [821] 13 __/__/__ (000 to 255) x Base time
[751] 6 __/__/__ (000 to 255) x Base time [831] 14 __/__/__ (000 to 255) x Base time
[761] 7 __/__/__ (000 to 255) x Base time [841] 15 __/__/__ (000 to 255) x Base time
[771] 8 __/__/__ (000 to 255) x Base time [851] 16 __/__/__ (000 to 255) x Base time

Section [700] - Option [5]

Virtual Input Base Time Selection
If option [5] is OFF, the value programmed for the Virtual Input Timer will be in seconds. If option [5] is ON, the Virtual Input Timer will be in
minutes. The following table lists the base time sections and their respective virtual inputs.

U = default setting
Virtual Virtual
Section [5] OFF [5] ON Section [5] OFF [5] ON
Input Input
[700] 1 U seconds N minutes [780] 9 U seconds N minutes
[710] 2 U seconds N minutes [790] 10 U seconds N minutes
[720] 3 U seconds N minutes [800] 11 U seconds N minutes
[730] 4 U seconds N minutes [810] 12 U seconds N minutes
[740] 5 U seconds N minutes [820] 13 U seconds N minutes
[750] 6 U seconds N minutes [830] 14 U seconds N minutes
[760] 7 U seconds N minutes [840] 15 U seconds N minutes
[770] 8 U seconds N minutes [850] 16 U seconds N minutes

6
Virtual PGM Programming
The Printer Module supports up to 30 virtual PGMs which are not related to any physical output on the module, but operate in the same
manner and are programmed in the same way as traditional PGMs. The tables below offer an example of the virtual PGM programming
sections which must be set for virtual PGM 1.

Section [100] : Virtual PGM Options

Option OFF ON

[1] and [2] Virtual PGM Deactivation

[3] Virtual PGM Base Time Selection U Seconds N Minutes

U Message N Message
[4] Virtual PGM Resend
not resent resent

Section Data Description Default

[101] __/__/__ (000 to 255) x Base Time Virtual PGM 1 Timer 005

Event Group Feature Group Start # End #

Section Section Section Section
Virtual PGM Activation [102] __/__/__ [103] __/__/__ [104] __/__/__ [105] __/__/__
Virtual PGM Deactivation [106] __/__/__ [107] __/__/__ [108] __/__/__ [109] __/__/__

Refer to the table below for a list of the programming sections for all virtual PGMs.

Virtual Virtual Virtual Virtual Virtual

Section Section Section Section Section
PGM PGM PGM PGM PGM
1 [100] - [109] 7 [160] - [169] 13 [220] - [229] 19 [280] - [289] 25 [340] - [349]
2 [110] - [119] 8 [170] - [179] 14 [230] - [239] 20 [290] - [299] 26 [350] - [359]
3 [120] - [129] 9 [180] - [189] 15 [240] - [249] 21 [300] - [309] 27 [360] - [369]
4 [130] - [139] 10 [190] - [199] 16 [250] - [259] 22 [310] - [319] 28 [370] - [379]
5 [140] - [149] 11 [200] - [209] 17 [260] - [269] 23 [320] - [329] 29 [380] - [389]
6 [150] - [159] 12 [210] - [219] 18 [270] - [279] 24 [330] - [339] 30 [390] - [399]

For more information on PGM programming, see “Appendix 1: Programming PGMs” on page 23.

The following describes the programming sections and options specific to the Printer Module’s virtual PGMs. Use the programming tables to
document specific settings for all programmed virtual PGMs.

Section [100] - Options [1] and [2]

Virtual PGM Deactivation Option
When the Virtual PGM Activation Event occurs, this option determines when the virtual PGM will
return to its normal state (deactivate). Depending on the programmed value, the virtual PGM can stay
activated indefinitely. It can also deactivate following a virtual deactivation event (see “Virtual PGM
Deactivation Event” on page 11) and/or after the Virtual PGM Timer has elapsed (see “Virtual PGM
Timers” on page 8).

7
 U = default setting
Virtual
Section [1] OFF / [2] OFF [1] ON / [2] OFF [1] OFF / [2] ON [1] ON / [2] ON
PGM
[100] 1 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[110] 2 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[120] 3 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[130] 4 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[140] 5 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[150] 6 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[160] 7 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[170] 8 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[180] 9 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[190] 10 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[200] 11 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[210] 12 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[220] 13 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[230] 14 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[240] 15 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[250] 16 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[260] 17 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[270] 18 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[280] 19 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[290] 20 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[300] 21 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[310] 22 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[320] 23 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[330] 24 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[340] 25 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[350] 26 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[360] 27 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[370] 28 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[380] 29 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[390] 30 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer

Section [101]
Virtual PGM Timers
If the virtual PGM is set to follow its Virtual PGM Timer (see “Virtual PGM Deactivation Option” on page 7), the entered value represents the
amount of time that the virtual PGM will remain activated. To program the Virtual PGM Timer, enter a 3-digit value from 000 to 255.
Depending on the Virtual PGM Base Time (see below), the Virtual PGM Timer will either be in seconds or minutes.

Section Virtual PGM Data Section Virtual PGM Data

[101] 1 __/__/__ (000 to 255) x Base time [251] 16 __/__/__ (000 to 255) x Base time
[111] 2 __/__/__ (000 to 255) x Base time [261] 17 __/__/__ (000 to 255) x Base time
[121] 3 __/__/__ (000 to 255) x Base time [271] 18 __/__/__ (000 to 255) x Base time
[131] 4 __/__/__ (000 to 255) x Base time [281] 19 __/__/__ (000 to 255) x Base time
[141] 5 __/__/__ (000 to 255) x Base time [291] 20 __/__/__ (000 to 255) x Base time
[151] 6 __/__/__ (000 to 255) x Base time [301] 21 __/__/__ (000 to 255) x Base time
[161] 7 __/__/__ (000 to 255) x Base time [311] 22 __/__/__ (000 to 255) x Base time
[171] 8 __/__/__ (000 to 255) x Base time [321] 23 __/__/__ (000 to 255) x Base time
[181] 9 __/__/__ (000 to 255) x Base time [331] 24 __/__/__ (000 to 255) x Base time
[191] 10 __/__/__ (000 to 255) x Base time [341] 25 __/__/__ (000 to 255) x Base time

8
 [201] 11 __/__/__ (000 to 255) x Base time [351] 26 __/__/__ (000 to 255) x Base time
[211] 12 __/__/__ (000 to 255) x Base time [361] 27 __/__/__ (000 to 255) x Base time
[221] 13 __/__/__ (000 to 255) x Base time [371] 28 __/__/__ (000 to 255) x Base time
[231] 14 __/__/__ (000 to 255) x Base time [381] 29 __/__/__ (000 to 255) x Base time
[241] 15 __/__/__ (000 to 255) x Base time [391] 30 __/__/__ (000 to 255) x Base time

Section [100] - Option [3]

Virtual PGM Base Time Selection
If option [3] is OFF, the value programmed for the Virtual PGM Timer will be in seconds. If option [3] is ON, the Virtual PGM Timer will be in
minutes. See the “Virtual PGM Deactivation Option” on page 7 table for relevant timer sections.
U = default setting
Virtual Virtual
Section [5] OFF [5] ON Section [5] OFF [5] ON
PGM PGM
[100] 1 U seconds N minutes [250] 16 U seconds N minutes
[110] 2 U seconds N minutes [260] 17 U seconds N minutes
[120] 3 U seconds N minutes [270] 18 U seconds N minutes
[130] 4 U seconds N minutes [280] 19 U seconds N minutes
[140] 5 U seconds N minutes [290] 20 U seconds N minutes
[150] 6 U seconds N minutes [300] 21 U seconds N minutes
[160] 7 U seconds N minutes [310] 22 U seconds N minutes
[170] 8 U seconds N minutes [320] 23 U seconds N minutes
[180] 9 U seconds N minutes [330] 24 U seconds N minutes
[190] 10 U seconds N minutes [340] 25 U seconds N minutes
[200] 11 U seconds N minutes [350] 26 U seconds N minutes
[210] 12 U seconds N minutes [360] 27 U seconds N minutes
[220] 13 U seconds N minutes [370] 28 U seconds N minutes
[230] 14 U seconds N minutes [380] 29 U seconds N minutes
[240] 15 U seconds N minutes [390] 30 U seconds N minutes

Section [100] - Option [4]

Virtual PGM Resend Option
If option [4] is ON and a virtual PGM’s activation event reoccurs while the virtual PGM is ON, the associated message sent to the home
automation system will be resent. If option [4] is ON and a Virtual PGM’s deactivation event reoccurs while the virtual PGM is OFF, the
associated message sent to the home automation system will be resent. See the “Virtual PGM Deactivation Option” on page 7 table for
relevant sections.
U = default setting
Virtual Virtual
Section [4] OFF [4] ON Section [4] OFF [4] ON
PGM PGM
[100] 1 U message not resent N message resent [250] 16 U message not resent N message resent
[110] 2 U message not resent N message resent [260] 17 U message not resent N message resent
[120] 3 U message not resent N message resent [270] 18 U message not resent N message resent
[130] 4 U message not resent N message resent [280] 19 U message not resent N message resent
[140] 5 U message not resent N message resent [290] 20 U message not resent N message resent
[150] 6 U message not resent N message resent [300] 21 U message not resent N message resent
[160] 7 U message not resent N message resent [310] 22 U message not resent N message resent
[170] 8 U message not resent N message resent [320] 23 U message not resent N message resent
[180] 9 U message not resent N message resent [330] 24 U message not resent N message resent
[190] 10 U message not resent N message resent [340] 25 U message not resent N message resent
[200] 11 U message not resent N message resent [350] 26 U message not resent N message resent
[210] 12 U message not resent N message resent [360] 27 U message not resent N message resent
[220] 13 U message not resent N message resent [370] 28 U message not resent N message resent
[230] 14 U message not resent N message resent [380] 29 U message not resent N message resent
[240] 15 U message not resent N message resent [390] 30 U message not resent N message resent

9
 Sections [102] to [105]
Virtual PGM Activation Event
The Virtual PGM Activation Event determines which event will activate the Printer Module’s virtual PGM output(s). The Event Group
specifies the event, the Feature Group identifies the source, and the Start # and End # set the range within the Feature Group.
Note that Event Groups [064] to [067] may be selected when programming virtual PGMs (see “Appendix 1: Programming PGMs” on
page 23).

Event Group Feature Group Start # End #

Section Section Section Section
Virtual PGM1 [102] __/__/__ [103] __/__/__ [104] __/__/__ [105] __/__/__
Virtual PGM2 [112] __/__/__ [113] __/__/__ [114] __/__/__ [115] __/__/__
Virtual PGM3 [122] __/__/__ [123] __/__/__ [124] __/__/__ [125] __/__/__
Virtual PGM4 [132] __/__/__ [133] __/__/__ [134] __/__/__ [135] __/__/__
Virtual PGM5 [142] __/__/__ [143] __/__/__ [144] __/__/__ [145] __/__/__
Virtual PGM6 [152] __/__/__ [153] __/__/__ [154] __/__/__ [155] __/__/__
Virtual PGM7 [162] __/__/__ [163] __/__/__ [164] __/__/__ [165] __/__/__
Virtual PGM8 [172] __/__/__ [173] __/__/__ [174] __/__/__ [175] __/__/__
Virtual PGM9 [182] __/__/__ [183] __/__/__ [184] __/__/__ [185] __/__/__
Virtual PGM10 [192] __/__/__ [193] __/__/__ [194] __/__/__ [195] __/__/__
Virtual PGM11 [202] __/__/__ [203] __/__/__ [204] __/__/__ [205] __/__/__
Virtual PGM12 [212] __/__/__ [213] __/__/__ [214] __/__/__ [215] __/__/__
Virtual PGM13 [222] __/__/__ [223] __/__/__ [224] __/__/__ [225] __/__/__
Virtual PGM14 [232] __/__/__ [233] __/__/__ [234] __/__/__ [235] __/__/__
Virtual PGM15 [242] __/__/__ [243] __/__/__ [244] __/__/__ [245] __/__/__
Virtual PGM16 [252] __/__/__ [253] __/__/__ [254] __/__/__ [255] __/__/__
Virtual PGM17 [262] __/__/__ [263] __/__/__ [264] __/__/__ [265] __/__/__
Virtual PGM18 [272] __/__/__ [273] __/__/__ [274] __/__/__ [275] __/__/__
Virtual PGM19 [282] __/__/__ [283] __/__/__ [284] __/__/__ [285] __/__/__
Virtual PGM20 [292] __/__/__ [293] __/__/__ [294] __/__/__ [295] __/__/__
Virtual PGM21 [302] __/__/__ [303] __/__/__ [304] __/__/__ [305] __/__/__
Virtual PGM22 [312] __/__/__ [313] __/__/__ [314] __/__/__ [315] __/__/__
Virtual PGM23 [322] __/__/__ [323] __/__/__ [324] __/__/__ [325] __/__/__
Virtual PGM24 [332] __/__/__ [333] __/__/__ [334] __/__/__ [335] __/__/__
Virtual PGM25 [342] __/__/__ [343] __/__/__ [344] __/__/__ [345] __/__/__
Virtual PGM26 [352] __/__/__ [353] __/__/__ [354] __/__/__ [355] __/__/__
Virtual PGM27 [362] __/__/__ [363] __/__/__ [364] __/__/__ [365] __/__/__
Virtual PGM28 [372] __/__/__ [373] __/__/__ [374] __/__/__ [375] __/__/__
Virtual PGM29 [382] __/__/__ [383] __/__/__ [384] __/__/__ [385] __/__/__
Virtual PGM30 [392] __/__/__ [393] __/__/__ [394] __/__/__ [395] __/__/__

10
 Sections [106] to [109]
Virtual PGM Deactivation Event
If the Virtual PGM Deactivation Option is set to follow the Virtual PGM Deactivation Event (see “Virtual PGM Deactivation Option” on
page 7), the virtual PGM will return to its normal state when the event programmed occurs (see table below). The Event Group specifies the
event, the Feature Group identifies the source, and the Start # and End # set the range within the Feature Group.

Enter the sections that correspond to the Event Group, Feature Group, Start # and End # of the PGM.

Event Group Feature Group Start # End #

Section Section Section Section
Virtual PGM1 [106] __/__/__ [107] __/__/__ [108] __/__/__ [109] __/__/__
Virtual PGM2 [116] __/__/__ [117] __/__/__ [118] __/__/__ [119] __/__/__
Virtual PGM3 [126] __/__/__ [127] __/__/__ [128] __/__/__ [129] __/__/__
Virtual PGM4 [136] __/__/__ [137] __/__/__ [138] __/__/__ [139] __/__/__
Virtual PGM5 [146] __/__/__ [147] __/__/__ [148] __/__/__ [149] __/__/__
Virtual PGM6 [156] __/__/__ [157] __/__/__ [158] __/__/__ [159] __/__/__
Virtual PGM7 [166] __/__/__ [167] __/__/__ [168] __/__/__ [169] __/__/__
Virtual PGM8 [176] __/__/__ [177] __/__/__ [178] __/__/__ [179] __/__/__
Virtual PGM9 [186] __/__/__ [187] __/__/__ [188] __/__/__ [189] __/__/__
Virtual PGM10 [196] __/__/__ [197] __/__/__ [198] __/__/__ [199] __/__/__
Virtual PGM11 [206] __/__/__ [207] __/__/__ [208] __/__/__ [209] __/__/__
Virtual PGM12 [216] __/__/__ [217] __/__/__ [218] __/__/__ [219] __/__/__
Virtual PGM13 [226] __/__/__ [227] __/__/__ [228] __/__/__ [229] __/__/__
Virtual PGM14 [236] __/__/__ [237] __/__/__ [238] __/__/__ [239] __/__/__
Virtual PGM15 [246] __/__/__ [247] __/__/__ [248] __/__/__ [249] __/__/__
Virtual PGM16 [256] __/__/__ [257] __/__/__ [258] __/__/__ [259] __/__/__
Virtual PGM17 [266] __/__/__ [267] __/__/__ [268] __/__/__ [269] __/__/__
Virtual PGM18 [276] __/__/__ [277] __/__/__ [278] __/__/__ [279] __/__/__
Virtual PGM19 [286] __/__/__ [287] __/__/__ [288] __/__/__ [289] __/__/__
Virtual PGM20 [296] __/__/__ [297] __/__/__ [298] __/__/__ [299] __/__/__
Virtual PGM21 [306] __/__/__ [307] __/__/__ [308] __/__/__ [309] __/__/__
Virtual PGM22 [316] __/__/__ [317] __/__/__ [318] __/__/__ [319] __/__/__
Virtual PGM23 [326] __/__/__ [327] __/__/__ [328] __/__/__ [329] __/__/__
Virtual PGM24 [336] __/__/__ [337] __/__/__ [338] __/__/__ [339] __/__/__
Virtual PGM25 [346] __/__/__ [347] __/__/__ [348] __/__/__ [349] __/__/__
Virtual PGM26 [356] __/__/__ [357] __/__/__ [358] __/__/__ [359] __/__/__
Virtual PGM27 [366] __/__/__ [367] __/__/__ [368] __/__/__ [369] __/__/__
Virtual PGM28 [376] __/__/__ [377] __/__/__ [378] __/__/__ [379] __/__/__
Virtual PGM29 [386] __/__/__ [387] __/__/__ [388] __/__/__ [389] __/__/__
Virtual PGM30 [396] __/__/__ [397] __/__/__ [398] __/__/__ [399] __/__/__

11
ASCII Protocol
The ASCII Protocol is a serial communication protocol which allows your home automation module to communicate with the Digiplex control
panel through the PRT3 Printer Module. The home automation module must be programmed with the ASCII Protocol in order for successful
communication to occur.

The ASCII Protocol is a means of communication involving the use of uppercase ASCII characters. All communications between the Printer
Module and the home automation module must end with a carriage return (ASCII #13).

When a command is sent from the home automation module to the Printer Module, it is acknowledged with a feedback echo. The Printer
Module will send the first five characters of the command back to the home automation module followed by “&OK” for valid commands,
“&fail” for invalid commands or with requested information when a valid command involves an information request. If the feedback consists
of an exclamation point (“!”) followed by a carriage return, this signifies that the command could not be accepted due to the fact that the
Printer Module’s reception buffer is full.

Printer Module to Digiplex Panel Communication Status

If the Printer Module fails to communicate with the Digiplex panel, the following command is used.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 Byte 8 Byte 9 Byte 10
C O M M & f a i l <cr>

The following command is used to signify communication has been restored. This command is also used upon startup to indicate that the
Printer Module is successfully communicating with the Digiplex control panel.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 Byte 8

C O M M & o k <cr>

Commands sent to the Printer Module from the Home Automation Module
The following lists the ASCII Protocol string codes and their respective commands from the home automation module to the Printer Module.

Virtual Input Open

The following commands set the virtual inputs’ status to “open”.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Virtual Input Open 01 V O 0 0 1 <cr>
Virtual Input Open 02 V O 0 0 2 <cr>
... LL
Virtual Input Open 16 V O 0 1 6 <cr>

Virtual Input Closed

The following commands set the virtual inputs’ status to “closed”.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Virtual Input Closed 01 V C 0 0 1 <cr>
Virtual Input Closed 02 V C 0 0 2 <cr>
... LL
Virtual Input Closed 16 V C 0 1 6 <cr>

12
Request Area Status
The following commands request the area status. For the panel’s maximum number of areas, refer to “Panel Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Request Area Status 01 R A 0 0 1 <cr>
Request Area Status 02 R A 0 0 2 <cr>
LL
Request Area Status 08 R A 0 0 8 <cr>

The Request Area Status command involves an information request. When the command is valid, the first five characters of the command
are returned followed by the requested information. The following provides an example of the information sent by the Printer Module to the
home automation module after having received a Request Area Status 01 command:

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7

D (Disarmed)
A (Armed) M (Zone in
R A 0 0 1 F (Force armed) memory)
S (Stay armed) O (Ok)
I (Instant armed)

Byte 8 Byte 9 Byte 10 Byte 11 Byte 12 Byte 13

P (In
T (Trouble) N (Not ready) A (In alarm) S (Strobe)
programming) <cr>
O (Ok) O (Ok) O (Ok) O (Ok)
O (Ok)

Request Zone Status

The following commands request the zone status. For the panel’s maximum number of zones, refer to “Panel Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Request Zone Status 01 R Z 0 0 1 <cr>
Request Zone Status 02 R Z 0 0 2 <cr>
LL
Request Zone Status 192 R Z 1 9 2 <cr>

The Request Zone Status command also involves an information request. When the command is valid, the first five characters of the
command are returned followed by the requested information. The following provides an example of the information sent by the Printer
Module to the home automation module after having received a Request Zone Status 01 command.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

C (Closed)
O (Open)
R Z 0 0 1
T (Tampered)
F (Fire loop trouble)

Byte 7 Byte 8 Byte 9 Byte 10 Byte 11

A (In alarm) F (Fire alarm) S (Supervision lost) L (Low battery)
<cr>
O (Ok) O (Ok) O (Ok) O (Ok)

Request Zone Label

The following commands request the zone label. For the panel’s maximum number of zones, refer to “Panel Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Request Zone Label 01 Z L 0 0 1 <cr>
Request Zone Label 02 Z L 0 0 2 <cr>
LL
Request Zone Label 192 Z L 1 9 2 <cr>

The Request Zone Label command also involves an information request. When the command is valid, the first five characters of the
command are returned followed by the requested zone label. All zone labels are 16 characters in length.

13
Request Area Label
The following commands request the area label. For the panel’s maximum number of areas, refer to “Panel Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Request Area Label 01 A L 0 0 1 <cr>
Request Area Label 02 A L 0 0 2 <cr>
LL
Request Area Label 08 A L 0 0 8 <cr>

The Request Area Label command also involves an information request. When the command is valid, the first five characters of the
command are returned followed by the requested area label. All area labels are 16 characters in length.

Request User Label

The following commands request the user label. For the panel’s maximum number of users, refer to “Panel Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Request User Label 01 U L 0 0 1 <cr>
Request User Label 02 U L 0 0 2 <cr>
LL
Request User Label 999 U L 9 9 9 <cr>

The Request User Label command also involves an information request. When the command is valid, the first five characters of the
command are returned followed by the requested user label. All user labels are 16 characters in length.

Area Arm
The following commands arm areas. For the panel’s maximum number of areas, refer to “Panel Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Bytes 7-12 Byte 13

A (Regular
arm)
Arm Area 01 A A 0 0 1 F (Force arm) xxxxxx* <cr>
S (stay arm)
I (Instant arm)
Arm Area 02 A A 0 0 2 “ “ <cr>
LL
Arm Area 08 A A 0 0 8 “ “ <cr>

* xxxxxx represents the code used to arm the system. If the code is shorter than six digits, enter only the appropriate amount of digits.

If an invalid user code is entered, the command will be returned followed by “&fail”.

Area Quick Arm

The following commands quick arm areas. For the panel’s maximum number of areas, refer to “Panel Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7

A (Regular
arm)
F (Force arm)
Quick Arm Area 01 A Q 0 0 1 <cr>
S (stay arm)
I (Instant
arm)

14
 A (Regular
arm)
Quick Arm Area 02 A Q 0 0 2 F (Force arm) <cr>
S (stay arm)
I (Instant arm
LL
A (Regular
arm)
Quick Arm Area 08 A Q 0 0 8 F (Force arm) <cr>
S (stay arm)
I (Instant arm

The One-Touch feature must be enabled in the Digiplex control panel to use this feature. See the appropriate Digiplex
control panel’s Reference and Installation Manual for more information.

Area Disarm
The following commands disarm areas. For the panel’s maximum number of areas, refer to “Panel Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Bytes 6-11 Byte 12

Disarm Area 01 A D 0 0 1 xxxxxx* <cr>
Disarm Area 02 A D 0 0 2 “ <cr>
LL
Disarm Area 08 A D 0 0 8 “ <cr>

* xxxxxx represents the code used to arm the system. If the code is shorter than six digits, enter only the appropriate amount of digits.

If an invalid user code is entered, the command will be returned followed by “&fail”.

Emergency Panic
The following commands are used for emergency panic alarms in up to eight areas. For the panel’s maximum number of areas, refer to
“Panel Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Panic 1 - Emergency Area 01 P E 0 0 1 <cr>
Panic 1 - Emergency Area 02 P E 0 0 2 <cr>
LL
Panic 1 - Emergency Area 08 P E 0 0 8 <cr>

Panic alarms must be individually enabled. See the appropriate Digiplex control panel’s Reference and Installation Manual
for more information.

Medical Panic
The following commands are used for medical panic alarms in up to eight areas. For the panel’s maximum number of areas, refer to “Panel
Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Panic 2 - Medical Area 01 P M 0 0 1 <cr>
Panic 2 - Medical Area 02 P M 0 0 2 <cr>
LL
Panic 2 - Medical Area 08 P M 0 0 8 <cr>

Panic alarms must be individually enabled. See the appropriate Digiplex control panel’s Reference and Installation Manual
for more information.

15
Fire Panic
The following commands are used for fire panic alarms in up to eight areas. For the panel’s maximum number of areas, refer to “Panel
Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Panic 3 - Fire Area 01 P F 0 0 1 <cr>
Panic 3 - Fire Area 02 P F 0 0 2 <cr>
LL
Panic 3 - Fire Area 08 P F 0 0 8 <cr>

Panic alarms must be individually enabled. See the appropriate Digiplex Control Panel Reference and Installation Manual
for more information.

Smoke Reset
The following commands are used for smoke detector resets in up to eight areas. For the panel’s maximum number of areas, refer to “Panel
Specifications” on page 1.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Smoke reset - Area 01 S R 0 0 1 <cr>
Smoke reset - Area 02 S R 0 0 2 <cr>
LL
Smoke reset - Area 08 S R 0 0 8 <cr>

Utility Key
The following commands are used for the utility keys (up to 251).

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Utility key 01 U K 0 0 1 <cr>
Utility key 02 U K 0 0 2 <cr>
LL
Utility key 251 U K 2 5 1 <cr>

Commands sent from the Printer Module to the Home Automation Module
The following lists the ASCII Protocol string codes and their respective commands from the Printer Module to the home automation
module.

Virtual PGM Events

When a virtual PGM is activated within the Printer Module, the following commands are sent to the home automation module.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7

Virtual PGM 01 ON P G M 0 1 O N
Virtual PGM 02 ON P G M 0 2 O N
LL
Virtual PGM 30 ON P G M 3 0 O N

When a virtual PGM is deactivated within the Printer Module, the following commands are sent to the home automation module.

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 Byte 8 Byte 9

Virtual PGM 01 OFF P G M 0 1 O F F <cr>
Virtual PGM 02 OFF P G M 0 2 O F F <cr>
LL
Virtual PGM 30 OFF P G M 3 0 O F F <cr>

16
System Events
All Digiplex system events are sent through the Printer Module to the home automation module using the following format.

Byte 1 Bytes 2-4 Byte 5 Bytes 6-8 Byte 9 Bytes 10-12

System Event G xxx* N yyy** A zzz***

* xxx represents the 3-digit event group (G).

** yyy represents the 3-digit event number (N).
*** zzz represents the 3-digit area number (A). Area number 000 signifies that the event has occurred in all enabled areas or is a global
event independent of area assignment.

As shown above, system events involve a 3-digit event group (Gxxx), a 3-digit event number (Nyyy) and a 3-digit area number (Azzz). The
following table lists the event group and event number descriptors that can be used to read the system event format. For example,
G001N005A006 means zone 5 in area 6 has been opened. (Event group 001= Zone open, Event number 005= zone 5, Area 006= area 6).

Event
Event Group Description Event Number (N) Event Number Description Area Number (A)
Group (G)
000 Zone is OK
001 Zone is Open
001-192 Zone Numbers 001-008
002 Zone is Tampered
003 Zone is in Fire Loop Trouble
000 TLM Trouble
001 Smoke detector reset
002 Arm with no entry delay
003 Arm in Stay mode
004 Non-reportable Event 004 Arm in Away mode 000-008
005 Full arm when in Stay mode
006 Voice module access
007 Remote control access
008 PC Fail to communicate
009 Midnight
010 NEware User Login
011 NEware User Logout
012 User Initiated Callup
013 Force Answer
014 Force Hangup
User Code entered on
005 000-999 User Codes 000-008
Keypad
006 User/Card Access on door 001-032 Door Numbers 000-008
Bypass Programming 000 One-touch Bypass Programming
007 001-008
Access 001-999 User Code
008 TX Delay Zone Alarm 001-192 Zone Numbers 001-008
009 Arming with Master 001-999 User Codes 001-008
010 Arming with User Code 001-999 User Codes 001-008
011 Arming with Keyswitch 001-032 Keyswitch numbers 001-008

17
 Event
Event Group Description Event Number (N) Event Number Description Area Number (A)
Group (G)
000 Auto Arming
001 Arming by WinLoad
002 Late to Close
003 No Movement Arming
012 Special Arming 004 Partial Arming 001-008
005 One-touch Arming
006 Future Use
007 Future Use
008 (InTouch) Voice Module Arming
013 Disarm with Master 001-999 User Codes 001-008
014 Disarm with User Code 001-999 User Codes 001-008
015 Disarm with Keyswitch 001-032 Keyswitch numbers 001-008
Disarm after alarm with
016 001-999 User Codes 001-008
Master
Disarm after alarm with
017 001-999 User Codes 001-008
User Code
Disarm after alarm with
018 001-032 Keyswitch numbers 001-008
Keyswitch
Alarm Cancelled with
019 001-999 User Codes 001-008
Master
Alarm Cancelled with User
020 001-999 User Codes 001-008
Code
Alarm Cancelled with
021 001-032 Keyswitch numbers 001-008
Keyswitch
000 Auto Arm Cancelled
001 One-touch Stay/Instant Disarm
002 Disarming with WinLoad
Disarming with WinLoad after
003
alarm
022 Special Disarm Events 004 WinLoad cancelled alarm 001-008
005 Future Use
006 Future Use
007 Future Use
(InTouch) Voice Module
008
Disarming
023 Zone Bypassed 001-192 Zone Numbers 001-008
024 Zone in Alarm 001-192 Zone Numbers 001-008
025 Fire Alarm 001-192 Zone Numbers 001-008
026 Zone Alarm Restore 001-192 Zone Numbers 001-008
027 Fire Alarm Restore 001-192 Zone Numbers 001-008
028 Early to Disarm by User 001-999 User Codes 001-008
029 Late to Disarm by User 001-999 User Codes 001-008
000 Emergency Panic (Keys 1 & 3)
001 Medical Panic (Keys 4 & 6)
002 Fire Panic (Keys 7 & 9)
030 Special Alarm 001-008
003 Recent Closing
004 Police Code
005 Global Shutdown
031 Duress Alarm by User 0-999 User Codes 001-008
032 Zone Shutdown 0-192 Zone Numbers 001-008
033 Zone Tamper 0-192 Zone Numbers 001-008

18
 Event
Event Group Description Event Number (N) Event Number Description Area Number (A)
Group (G)
034 Zone Tamper Restore 001-192 Zone Numbers 001-008
035 Special Tamper 000 Keypad Lockout 001-008
000 TLM Trouble
001 AC Failure
002 Battery Failure
003 Auxiliary Current Limit
036 Trouble Event 000-008
004 Bell Current Limit
005 Bell Absent
006 Clock Trouble
007 Global Fire Loop
000 TLM Trouble
001 AC Failure
002 Battery Failure
003 Auxiliary Current Limit
037 Trouble Restore 000-008
004 Bell Current Limit
005 Bell Absent
006 Clock Trouble
007 Global Fire Loop
000 Combus Fault
001 Module Tamper
002 ROM/RAM error
003 TLM Trouble
038 Module Trouble 004 Fail to Communicate 000-008
005 Printer Fault
006 AC Failure
007 Battery Failure
008 Auxiliary Failure
000 Combus Fault
001 Module Tamper
002 ROM/RAM error
003 TLM Trouble
039 Module Trouble Restore 004 Fail to Communicate 000-008
005 Printer Fault
006 AC Failure
007 Battery Failure
008 Auxiliary Failure
Fail to Communicate on
040 001-004 Telephone Number 000-008
telephone Number
041 Low Battery on Zone 001-192 Zone Numbers 001-008
042 Zone Supervision Trouble 001-192 Zone Numbers 001-008
Low Battery on Zone
043 001-192 Zone Numbers 001-008
Restored
Zone Supervision Trouble
044 001-192 Zone Numbers 001-008
Restored

19
 Event
Event Group Description Event Number (N) Event Number Description Area Number (A)
Group (G)
000 Power up after total power down
001 Software reset (Watchdog)
002 Test Report
003 Future Use
045 Special Events 000-008
004 WinLoad In (connected)
005 WinLoad Out (disconnected)
006 Installer in programming
007 Installer out of programming
046 Early to Arm by User 001-999 User Codes 001-008
047 Late to Arm by User 001-999 User Codes 001-008
048 Utility Key 001-251 Utility Key 000-008
049 Request for Exit 001-032 Door Numbers 000-008
050 Access Denied 001-032 Door Numbers 000-008
051 Door Left Open Alarm 001-032 Door Numbers 000-008
052 Door Forced Alarm 001-032 Door Numbers 000-008
053 Door Left Open Restore 001-032 Door Numbers 000-008
054 Door Forced Open Restore 001-032 Door Numbers 000-008
055 Intellizone Triggered 001-192 Zone Numbers 000-008
New Module Assigned on 000 Module Address 001 to 254
058
Combus 255 Any Module Not Used
Module Manually Removed 000 Module Address 001 to 254
059
From Combus 255 Any Module Not Used
060 - 061 Future Use Future Use Future Use Future Use
062 Access Granted to User 000-999 User Codes 000-008
063 Access Denied to User 000-999 User Codes 000-008
Armed 000
Force Armed 001
Stay Armed 002
See Note 1 Instant Armed 003
064 Status 1
on page 21 Strobe Alarm 004
Silent Alarm 005
Audible Alarm 006
Fire Alarm 007
Ready 000
Exit Delay 001
Entry Delay 002
System in Trouble 003
See Note 1
065 Status 2 Alarm in Memory 004
on page 21
Zones Bypassed 005
Bypass, Master, Installer
006
Programming
Keypad Lockout 007

20
 Event
Event Group Description Event Number (N) Event Number Description Area Number (A)
Group (G)
Intellizone Delay Engaged** 000
Fire Delay Engaged 001
Auto Arm 002
Arming with Voice Module (set until
See Note 1 003
066 Status 3 Exit Delay finishes)
on page 21
Tamper 004
Zone Low Battery 005
Fire Loop Trouble 006
Zone Supervision Trouble 007
NOTE 1: 000 = Occurs in all areas enabled in the system (see section [3031]).
001 = Area 1 003 = Areaarea 3 005 = Area 5 007 = Area 7 255 = Occurs in at least one area enabled in the system.
002 = Area 2 004 = Area 4 006 = Area 6 008 = Area 8

*: If a Keyswitch Input is used, the input must be defined as “Generates a Utility Key Event on Open” or “Generates a Utility Key Event on Open
and Close”. If a remote control is used, the remote control button must be defined as a Utility Key button.

** This event cannot be used for a module’s PGM programming.

†
: Actions that Activate a Utility Key Event

21
 Figure 2: .PRT3 Connection

1) Green “RX” LED: Flashes when the Printer Module is receiving data through the serial port only.

2) Red “TX” LED: Flashes when the Printer Module is transmitting data through the serial port only.

3) 25-Pin Parallel Port: Connect the Printer Module’s 25-pin parallel port to any dot matrix printer.
Note: The dot matrix printer must support a minimum of 80 columns.

4) 9-Pin Serial Port: Connect the Printer Module’s 9-Pin serial port to a dot matrix printer.
Note: The dot matrix printer must support a minimum of 80 columns.

5) 9-pin Serial Port: Connect the Printer Module’s 9-pin serial port to a home automation module.

6) 9-pin Serial Port: Connect C-Bus to the Printer Module using a null modem cable.

7) 9-pin Serial Port: Connect either the Printer Module’s USB or 9-pin serial port to a computer’s COM port to view the control panel’s events on
the computer’s monitor. The events display on the monitor can then be printed through the printer connected to the computer.

Remove AC power and battery before adding a module to the system. Refer to the Digplex EVO
or DGP-848 Reference & Installation Manual for the maximum allowable installation distance
from the control panel.

Printer cable length must not exceed 25ft.

For information on using the Printer Module as an interface with home automation modules, see
the ASCII Protocol Programming Instructions or C-Bus Programming Instructions.

22
 Appendix 1: Programming PGMS
A PGM is a programmable output that toggles to its opposite state (i.e. a normally open PGM will close) when a specific event occurs in the
system. For example, a PGM can be used to reset smoke detectors, activate strobe lights, open/close garage doors and much more.

PGM Activation Event

The PGM Activation Event determines which event from which source will activate the PGM. The Event Group specifies the event, the
Feature Group identifies the source, and the Start # and End # sets the range within the Feature Group (see PGM Programming Table
below).

For example, the PRT3 can activate Virtual PGM1 when the area is armed by User Access Codes 256 to 260. Therefore:
Event Group section [102] = 010 “Arming with User Code”
Feature Group section [103] = 001 “User Codes 256 to 511”
Start # section [104] = 000 (representing user code 256)
End # section [105] = 004 (representing user code 260)

Enter the sections that correspond to the Event Group, Feature Group, Start # and End # of the desired PGM and enter the data as required.

PGM Deactivation Option

Once the PGMs are activated, they can deactivate when another event occurs or after a period of time. The PGM Deactivation Option
determines which method is used, the PGM Deactivation Event or the PGM Timer. Enter the section that corresponds to the desired PGM
and enable or disable the option.

PGM Deactivation Event

When the PGM Deactivation Option (see above) is disabled, the PGM Deactivation Event determines which event from which source will
return the PGM to its original state. The Event Group specifies the event, the Feature Group identifies the source, and the Start # and End #
determine the range within the Feature Group. The complete PGM Programming Table appears below.

For example, the PRT3 can deactivate Virtual PGM1 when zone 3 opens. Therefore:
Event Group section [106] = 001 “Zone is Open”
Feature Group section [107] = 000 “Zone Numbers”
Start # section [108] = 003
End # section [109] = 003

Enter the sections that correspond to the Event Group, Feature Group, Start # and End # of the desired PGM and enter the data as required.

PGM Programming Table

Event Group Feature Group Start # End #
PGM Activation
PGM __/__/__ __/__/__ __/__/__ __/__/__
Event
PGM Deactivation
PGM __/__/__ __/__/__ __/__/__ __/__/__
Event

Event
Event Feature Group Feature Start # End #
Group
000 Zone Numbers 001 to 192 001 to 192
000 Zone is OK
255 Any zone number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
001 Zone is Open
255 Any zone number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
002 Zone is Tampered
255 Any zone number Not Used Not Used

23
Event
Event Feature Group Feature Start # End #
Group
000 Zone Numbers 001 to 192 001 to 192
003 Zone is in Fire Loop Trouble
255 Any zone number Not Used Not Used
TLM Trouble (see NOTE 3 on
000 000
page 29)
Smoke detector reset 001 001
Arm with no entry delay 002 002
Arm in Stay mode 003 003
Arm in Away mode 004 004
Full arm when in Stay mode 005 005
Voice module access 006 006
000
004 Non-reportable Event Remote control access 007 007
PC Fail to communicate 008 008
Midnight 009 009
NEware User Login 010 010
NEware User Logout 011 011
User Initiated Callup 012 012
Force Answer 013 013
Force Hangup 014 014
255 Any non-reportable event Not Used Not Used
000 User Codes 000 to 255 000 to 255 000 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
User Code entered on
005 002 User Codes 512 to 767 000 to 255 000 to 255
Keypad
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Door Numbers 001 to 032 001 to 032
006 User/Card Access on door
255 Any door number Not Used Not Used
000 One-touch Bypass Programming 000 000
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
007 Bypass Programming Access
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
008 TX Delay Zone Alarm
255 Any zone number Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
009 Arming with Master 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
010 Arming with User Code 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Keyswitch numbers 001 to 032 001 to 032
011 Arming with Keyswitch
255 Any keyswitch number Not Used Not Used

24
 Event
Event Feature Group Feature Start # End #
Group
Auto Arming 000 000
Arming by WinLoad 001 001
Late to Close 002 002
No Movement Arming 003 003
000
Partial Arming 004 004
012 Special Arming
One-touch Arming 005 005
Future Use 006 006
Future Use 007 007
(InTouch) Voice Module Arming 008 008
255 Any special arming event Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
013 Disarm with Master 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
014 Disarm with User Code 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Keyswitch numbers 001 to 032 001 to 032
015 Disarm with Keyswitch
255 Any keyswitch Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
Disarm after alarm with
016 002 User Codes 512 to 767 000 to 255 000 to 255
Master
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
Disarm after alarm with User
017 002 User Codes 512 to 767 000 to 255 000 to 255
Code
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
Disarm after alarm with 000 Keyswitch numbers 001 to 032 001 to 032
018
Keyswitch 255 Any keyswitch Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
019 Alarm Cancelled with Master 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
Alarm Cancelled with User
020 002 User Codes 512 to 767 000 to 255 000 to 255
Code
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
Alarm Cancelled with 000 Keyswitch numbers 001 to 032 001 to 032
021
Keyswitch 255 Any keyswitch Not Used Not Used

25
Event
Event Feature Group Feature Start # End #
Group
Auto Arm Cancelled 000 000
One-touch Stay/Instant Disarm 001 001
Disarming with WinLoad 002 002
Disarming with WinLoad after
003 003
alarm
000 WinLoad cancelled alarm 004 004
022 Special Disarm Events
Future Use 005 005
Future Use 006 006
Future Use 007 007
(InTouch) Voice Module
008 008
Disarming
255 Any special disarm event Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
023 Zone Bypassed
255 Any zone number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
024 Zone in Alarm
255 Any zone number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
025 Fire Alarm
255 Any zone number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
026 Zone Alarm Restore
255 Any zone number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
027 Fire Alarm Restore
255 Any zone number Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
028 Early to Disarm by User 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
029 Late to Disarm by User 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
Emergency Panic (Keys 1 & 3) 000 000
Medical Panic (Keys 4 & 6) 001 001
Fire Panic (Keys 7 & 9) 002 002
000
030 Special Alarm Recent Closing 003 003
Police Code 004 004
Global Shutdown 005 005
255 Any special alarm event Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 001 to 255 001 to 255
031 Duress Alarm by User 002 User Codes 512 to 767 001 to 255 001 to 255
003 User Codes 768 to 999 001 to 231 001 to 231
255 Any User Code Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
032 Zone Shutdown
255 Any zone number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
033 Zone Tamper
255 Any zone number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
034 Zone Tamper Restore
255 Any zone number Not Used Not Used
035 Special Tamper 000 Keypad Lockout 000 000

26
 Event
Event Feature Group Feature Start # End #
Group
TLM Trouble (see NOTE 2 on
000 000
page 29)
AC Failure 001 001
Battery Failure 002 002
000 Auxiliary Current Limit 003 003
036 Trouble Event
Bell Current Limit 004 004
Bell Absent 005 005
Clock Trouble 006 006
Global Fire Loop 007 007
255 Any trouble event Not Used Not Used
TLM Trouble 000 000
AC Failure 001 001
Battery Failure 002 002
Auxiliary Current Limit 003 003
000
037 Trouble Restore Bell Current Limit 004 004
Bell Absent 005 005
Clock Trouble 006 006
Global Fire Loop 007 007
255 Any trouble restore event Not Used Not Used
Combus Fault 000 000
Module Tamper 001 001
ROM/RAM error 002 002
TLM Trouble 003 003
000 Fail to Communicate 004 004
038 Module Trouble
Printer Fault 005 005
AC Failure 006 006
Battery Failure 007 007
Auxiliary Failure 008 008
255 Any module trouble Not Used Not Used
Combus Fault 000 000
Module Tamper 001 001
ROM/RAM error 002 002
TLM Trouble 003 003
000 Fail to Communicate 004 004
039 Module Trouble Restore
Printer Fault 005 005
AC Failure 006 006
Battery Failure 007 007
Auxiliary Failure 008 008
255 Any module trouble restore event Not Used Not Used
Fail to Communicate on 000 Telephone Number 001 to 004 001 to 004
040
telephone Number 255 Any telephone number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
041 Low Battery on Zone
255 Any zone number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
042 Zone Supervision Trouble
255 Any zone number Not Used Not Used
Low Battery on Zone 000 Zone Numbers 001 to 192 001 to 192
043
Restored 255 Any zone number Not Used Not Used
Zone Supervision Trouble 000 Zone Numbers 001 to 192 001 to 192
044
Restored 255 Any zone number Not Used Not Used

27
 Event
Event Feature Group Feature Start # End #
Group
Power up after total power down 000 000
Software reset (Watchdog) 001 001
Test Report 002 002
Future Use 003 003
000
045 Special Events WinLoad In (connected) 004 004
WinLoad Out (disconnected) 005 005
Installer in programming 006 006
Installer out of programming 007 007
255 Any special event Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
046 Early to Arm by User 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
047 Late to Arm by User 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Utility Key 001 to 064†* 001 to 064 001 to 064
048 Utility Key
255 Any UtilityKey†* Not Used Not Used
000 Door numbers 001 to 032 001 to 032
049 Request for Exit
255 Any door number Not Used Not Used
000 Door numbers 001 to 032 001 to 032
050 Access Denied
255 Any door number Not Used Not Used
000 Door numbers 001 to 032 001 to 032
051 Door Left Open Alarm
255 Any door number Not Used Not Used
000 Door numbers 001 to 032 001 to 032
052 Door Forced Alarm
255 Any door number Not Used Not Used
000 Door numbers 001 to 032 001 to 032
053 Door Left Open Restore
255 Any door number Not Used Not Used
000 Door numbers 001 to 032 001 to 032
054 Door Forced Open Restore
255 Any door number Not Used Not Used
000 Zone Numbers 001 to 192 001 to 192
055 Intellizone Triggered
255 Any zone number Not Used Not Used
Zone Excluded on Force 000 Zone Numbers 001 to 192 001 to 192
056
Arming 255 Any zone number Not Used Not Used
Zone Went Back to Arm 000 Zone Numbers 001 to 192 001 to 192
057
Status 255 Any zone number Not Used Not Used
New Module Assigned on 000 Module Numbers 001 to 254 001 to 254
058
Combus 255 Any moduel number Not Used Not Used
Module Manually Removed 000 Module Numbers 001 to 254 001 to 254
059
From Combus 255 Any moduel number Not Used Not Used
060 - 061 Future Use Future Use Future Use Future Use Future Use
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
062 Access Granted to User 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
†: see page 29
*: see page 29

28
 Event
Event Feature Group Feature Start # End #
Group
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
063 Access Denied to User 002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
Armed 000 000
Force Armed 001 001
Stay Armed 002 002
See Note 1 Instant Armed 003 003
064 Status 1
on page 29 Strobe Alarm 004 004
Silent Alarm 005 005
Audible Alarm 006 006
Fire Alarm 007 007
Ready 000 000
Exit Delay 001 001
Entry Delay 002 002
System in Trouble 003 003
See Note 1
065 Status 2 Alarm in Memory 004 004
on page 29
Zones Bypassed 005 005
Bypass, Master, Installer
006 006
Programming
Keypad Lockout 007 007
Intellizone Delay Engaged (see
000 000
Note 4 on page 29)
Fire Delay Engaged 001 001
Auto Arm 002 002
See Note 1 Arming with Voice Module (set
066 Status 3 003 003
on page 29 until Exit Delay finishes)
Tamper 004 004
Zone Low Battery 005 005
Fire Loop Trouble 006 006
Zone Supervision Trouble 007 007
067 Future Use Future Use Future Use Future Use Future Use

NOTE 1: 000 = Occurs in all areas enabled in the system (refer to the appropriate control panel Programming Guide).
001 = Area 1 003 = Area 3 005 = Area 5 (EVO96/EVO192/DGP-NE96 only) 007 = Area 7 (EVO96/EVO192/DGP-NE96 only)
002 = Area 2 004 = Area 4 006 = Area 6 (EVO96/EVO192/DGP-NE96 only) 008 = Area 8 (EVO96/EVO192/DGP-NE96 only)
255 = Occurs in at least one area enabled in the system.

NOTE 2:This TLM trouble event can only be used with DGP-NE96 control panels that have two dialers.

NOTE 3: This TLM trouble event can only be used with control panels that have one dialer.

NOTE 4: This event cannot be used for a module’s PGM programming.

* If a Keyswitch Input is used, the input must be defined as “Generates a Utility Key Event on Open” or “Generates a Utility Key Event on
Open and Close”. If a remote control is used, the remote control button must be defined as a Utility Key button.

†Actions
that Activate a Utility Key Event

29
 Actions
Utility Key Event Keyswitch Inputs Keyswitch Inputs
Keypad Utility Keys Remote Control
(definition = [3]) (definition = [4])
Utility Key Event 1 [1] & [2] KS** Input 1 opens KS** Input 1 opens Utility Key 1 RC button‡
Utility Key Event 2 [4] & [5] KS** Input 2 opens KS** Input 1 closes Utility Key 2 RC button‡
Utility Key Event 3 [7] & [8] KS** Input 3 opens KS** Input 2 opens Utility Key 3 RC button‡
Utility Key Event 4 [CLEAR] & [0] or [*] & [0] KS** Input 4 opens KS** Input 2 closes Utility Key 4 RC button‡
Utility Key Event 5 [2] & [3] KS** Input 5 opens KS** Input 3 opens Utility Key 5 RC button‡
Utility Key Event 6 [5] & [6] KS** Input 6 opens KS** Input 3 closes N/A
Utility Key Event 7 [8] & [9] KS** Input 7 opens KS** Input 4 opens N/A
Utility Key Event 8 [0] & [ENTER] or [0] & [#] KS** Input 8 opens KS** Input 4 closes N/A
Utility Key Event 9 N/A KS** Input 9 opens KS** Input 5 opens N/A
Utility Key Event 10 N/A KS** Input 10 opens KS** Input 5 closes N/A
Utility Key Event 11 N/A KS** Input 11 opens KS** Input 6 opens N/A
Utility Key Event 12 N/A KS** Input 12 opens KS** Input 6 closes N/A
Utility Key Event 13 N/A KS** Input 13 opens KS** Input 7 opens N/A
Utility Key Event 14 N/A KS** Input 14 opens KS** Input 7 closes N/A
Utility Key Event 15 N/A KS** Input 15 opens KS** Input 8 opens N/A
Utility Key Event 16 N/A KS** Input 16 opens KS** Input 8 closes N/A
Utility Key Event 17 N/A KS** Input 17 opens KS** Input 9 opens N/A
Utility Key Event 18 N/A KS** Input 18 opens KS** Input 9 closes N/A
L N/A L L N/A
Utility Key Event 31 N/A KS** Input 31 opens KS** Input 16 opens N/A
Utility Key Event 32 N/A KS** Input 32 opens KS** Input 16 closes N/A
Utility Key Event 33 N/A N/A KS** Input 17 opens N/A
Utility Key Event 34 N/A N/A KS** Input 17 closes N/A
L N/A N/A L N/A
Utility Key Event 63 N/A N/A KS** Input 32 opens N/A
Utility Key Event 64 N/A N/A KS** Input 32 closes N/A

** Keyswitch
‡ Referto the Magellan™ Reference and Installation Manual for remote control button programming instructions.

Warranty
Paradox Security Systems Ltd. (“Seller”) warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Except as specifically stated herein, all express or
implied warranties whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded. Because Seller does not
install or connect the products and because the products may be used in conjunction with products not manufactured by Seller, Seller cannot guarantee the performance of the security system and shall not be
responsible for circumstances resulting from the product’s inability to operate. Seller obligation and liability under this warranty is expressly limited to repairing or replacing, at Seller's option, any product not
meeting the specifications. Returns must include proof of purchase and be within the warranty period. In no event shall the Seller be liable to the buyer or any other person for any loss or damages whether direct
or indirect or consequential or incidental, including without limitation, any damages for lost profits stolen goods, or claims by any other party, caused by defective goods or otherwise arising from the improper,
incorrect or otherwise faulty installation or use of the merchandise sold.

Notwithstanding the preceding paragraph, the Seller’s maximum liability will be strictly limited to the purchase price of the defective product. Your use of this product signifies your acceptance of this warranty.

BEWARE: Dealers, installers and/or others selling the product are not authorized to modify this warranty or make additional warranties that are binding on the Seller.

© 2003-2009 Paradox Security Systems Ltd. All rights reserved. Specifications may change without prior notice. One or more of the following US patents may apply: 7046142, 6215399, 6111256, 6104319,
5920259, 5886632, 5721542, 5287111, 5119069, 5077549 and RE39406 and other pending patents may apply. Canadian and international patents may also apply.

Digiplex is a trademark or registered trademark of Paradox Security Systems Ltd. or its affiliates in Canada, the United States and/or other countries. Windows® is a registered trademark of Microsoft corporation.
Procomm™ is a trademark of Datastorm Technologies Inc.. Telix© - Copyright© 1986-1996 by DeltaComm Development & ELSA. HyperTerminal® is a registered trademark of Hilgraeve Inc..
C-Bus is a trademark of Clipsal Integrated Systems Pty Ltd..

30
For technical support in Canada or the U.S., call 1-800-791-1919, Monday to Friday from 8:00 a.m.
to 8:00 p.m. EST. For technical support outside Canada and the U.S., call 00-1-450-491-7444,
Monday to Friday from 8:00 a.m. to 8:00 p.m. EST. Please feel free to visit our website at
www.paradox.com.

Printed in Canada 09/2009 PARADOX.COM ASCII-EP01