Fundamentals of Thermal-Fluid Sciences

4th Edition in SI Units

Yunus A. Çengel, John M. Cimbala, Robert H. Turner
McGraw-Hill, 2012

Chapter 17
STEADY HEAT CONDUCTION

Lecture slides by
Mehmet Kanoğlu

Copyright © 2012 The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
 Objectives
• Understand the concept of thermal resistance and its
limitations, and develop thermal resistance networks for
practical heat conduction problems
• Solve steady conduction problems that involve multilayer
rectangular, cylindrical, or spherical geometries
• Develop an intuitive understanding of thermal contact
resistance, and circumstances under which it may be
significant
• Identify applications in which insulation may actually
increase heat transfer
• Analyze finned surfaces, and assess how efficiently and
effectively fins enhance heat transfer

2
17-1 STEADY HEAT CONDUCTION IN PLANE WALLS
Heat transfer through the wall of a house can be
modeled as steady and one-dimensional.
The temperature of the wall in this case depends
on one direction only (say the x-direction) and
can be expressed as T(x).

for steady operation

In steady operation, the rate of heat transfer
through the wall is constant.

Fourier’s law of
heat conduction

3
 The rate of heat conduction through
a plane wall is proportional to the
average thermal conductivity, the
wall area, and the temperature
difference, but is inversely
proportional to the wall thickness.
Once the rate of heat conduction is
available, the temperature T(x) at
any location x can be determined by
Under steady conditions, the
replacing T2 by T, and L by x.
temperature distribution in a plane
wall is a straight line: dT/dx = const.
4
Thermal Resistance Concept

Conduction resistance of the

wall: Thermal resistance of the
wall against heat conduction.
Thermal resistance of a medium Analogy between thermal and electrical
depends on the geometry and the resistance concepts.
thermal properties of the medium.
rate of heat transfer  electric current
thermal resistance  electrical resistance
Electrical resistance temperature difference  voltage difference

5
Newton’s law of cooling

Convection resistance of the

surface: Thermal resistance of the
surface against heat convection.

Schematic for convection resistance at a surface.

When the convection heat transfer coefficient is very large (h → ),

the convection resistance becomes zero and Ts  T.
That is, the surface offers no resistance to convection, and thus it
does not slow down the heat transfer process.
This situation is approached in practice at surfaces where boiling
and condensation occur. 6
 Radiation resistance of the
surface: Thermal resistance of the
surface against radiation.

Radiation heat transfer coefficient

Combined heat transfer

coefficient

Schematic for
convection and radiation
7
resistances at a surface.
 Thermal Resistance Network

The thermal resistance network for heat transfer through a plane wall subjected to
convection on both sides, and the electrical analogy.

8
Temperature drop

U overall heat
transfer coefficient

Once Q is evaluated, the

surface temperature T1 can
be determined from

The temperature drop across a layer is

proportional to its thermal resistance.
9
 Multilayer
Plane
Walls
The thermal resistance
network for heat transfer
through a two-layer plane
wall subjected to
convection on both sides.

10
11
12
13
14
17-2 THERMAL CONTACT RESISTANCE

Temperature distribution and heat flow lines along two solid plates
15
pressed against each other for the case of perfect and imperfect contact.
• When two such surfaces are
pressed against each other, the
peaks form good material
contact but the valleys form
voids filled with air.
• These numerous air gaps of
varying sizes act as insulation
because of the low thermal
conductivity of air.
• Thus, an interface offers some
resistance to heat transfer, and
this resistance per unit interface
area is called the thermal
contact resistance, Rc.

A typical experimental
setup for the
determination of thermal
contact resistance
16
 The value of thermal
contact resistance
hc thermal contact depends on:
conductance • surface roughness,
• material properties,
• temperature and
pressure at the
interface
• type of fluid trapped
at the interface.

Thermal contact resistance is significant and can even dominate the

heat transfer for good heat conductors such as metals, but can be
disregarded for poor heat conductors such as insulations. 17
The thermal contact resistance can
be minimized by applying
• a thermal grease such as silicon oil
• a better conducting gas such as
helium or hydrogen
• a soft metallic foil such as tin, silver, Effect of metallic coatings on
thermal contact conductance 18
copper, nickel, or aluminum
Contact resistance of transistors

The thermal contact conductance at the interface of two 1-

cm-thick aluminum plates is measured to be 11,000 W/m2
·°C. Determine the thickness of the aluminum plate whose
thermal resistance is equal to the thermal resistance of the
interface between the plates (Fig. 17–17).

19
The thermal contact conductance is highest (and thus the contact
resistance is lowest) for soft metals with smooth surfaces at high pressure. 20
17-3 GENERALIZED THERMAL RESISTANCE
NETWORKS

Thermal
resistance
network for two
parallel layers. 21
Two assumptions in solving complex
multidimensional heat transfer
problems by treating them as one-
dimensional using the thermal
resistance network are
(1) any plane wall normal to the x-axis is
isothermal (i.e., to assume the
temperature to vary in the x-direction
only)
(2) any plane parallel to the x-axis is
adiabatic (i.e., to assume heat transfer Thermal resistance network for
to occur in the x-direction only) combined series-parallel
Do they give the same result? 22
arrangement.
A 17-m-high and 5-m-wide wall consists of long 16-cm x
22-cm cross section horizontal bricks (k=0.72 W/m·°C)
separated by 3-cm-thick plaster layers (k=0.22 W/m·°C).
There are also 2-cm-thick plaster layers on each side of the
brick and a 3-cm-thick rigid foam (k=0.026 W/m·°C) on the
inner side of the wall, as shown in Fig. 17–21. The indoor
and the outdoor temperatures are 20°C and -10°C,
respectively, and the convection heat transfer coefficients
on the inner and the outer sides are h1 =10 W/m2 ·°C and
h2 =25 W/m2·°C, respectively. Assuming one-dimensional
heat transfer and disregarding radiation, determine the rate
of heat transfer through the wall.
23
24
17-4 HEAT CONDUCTION IN CYLINDERS AND
SPHERES
Heat transfer through the pipe
can be modeled as steady
and one-dimensional.
The temperature of the pipe
depends on one direction only
(the radial r-direction) and can
be expressed as T = T(r).
The temperature is
independent of the azimuthal
angle or the axial distance.
This situation is approximated
in practice in long cylindrical
Heat is lost from a hot-water pipe to
pipes and spherical
the air outside in the radial direction,
containers.
and thus heat transfer from a long
pipe is one-dimensional. 25
A long cylindrical pipe (or spherical
shell) with specified inner and outer
surface temperatures T1 and T2.

Conduction resistance of the cylinder layer

26
 A spherical shell
with specified
inner and outer
surface
temperatures T1
and T2.

Conduction resistance of the spherical layer

27
 for a cylindrical layer

for a spherical layer

The thermal resistance
network for a cylindrical (or
spherical) shell subjected
to convection from both the
inner and the outer sides.
28
Multilayered Cylinders and Spheres

The thermal resistance

network for heat transfer
through a three-layered
composite cylinder
subjected to convection
on both sides.

29
 Once heat transfer rate Q has been
calculated, the interface temperature
T2 can be determined from any of the
following two relations:

30
Heat loss through an insulated
steam pipe
Steam at T∞1 = 320°C flows in a cast iron pipe (k = 80 W/m
·°C) whose inner and outer diameters are D1 = 5 cm and D2
= 5.5 cm, respectively. The pipe is covered with 17-cm-
thick glass wool insulation with k =0.05 W/m ·°C. Heat is
lost to the surroundings at T∞2 =5°C by natural convection
and radiation, with a combined heat transfer coefficient of
h2 =18 W/m2 ·°C. Taking the heat transfer coefficient inside
the pipe to be h1 = 60 W/m2·°C, determine the rate of heat
loss from the steam per unit length of the pipe. Also
determine the temperature drops across the pipe shell and
the insulation.

31
32
Heat transfer to a spherical
container
A 17-m internal diameter spherical tank made of 2-cm-thick
stainless steel (k =15 W/m·°C) is used to store iced water
at T∞1 =0°C. The tank is located in a room whose
temperature is T∞2 = 22°C. The walls of the room are also
at 22°C. The outer surface of the tank is black and heat
transfer between the outer surface of the tank and the
surroundings is by natural convection and radiation. The
convection heat transfer coefficients at the inner and the
outer surfaces of the tank are h1 = 80 W/m2·°C and h2 =10
W/m2 ·°C, respectively. Determine the rate of heat transfer
to the iced water in the tank

33
34
17-5 CRITICAL RADIUS OF INSULATION
Adding more insulation to a wall or
to the attic always decreases heat
transfer since the heat transfer area
is constant, and adding insulation
always increases the thermal
resistance of the wall without
increasing the convection
resistance.
In a a cylindrical pipe or a spherical
shell, the additional insulation
increases the conduction
resistance of the insulation layer
but decreases the convection An insulated cylindrical pipe exposed to
resistance of the surface because convection from the outer surface and
of the increase in the outer surface the thermal resistance network
area for convection. associated with it.
The heat transfer from the pipe
may increase or decrease,
depending on which effect
dominates. 35
The critical radius of insulation
for a cylindrical body:

The critical radius of insulation

for a spherical shell:

The largest value of the critical

radius we are likely to
encounter is

We can insulate hot-water or

steam pipes freely without The variation of heat transfer
worrying about the possibility of rate with the outer radius of the
increasing the heat transfer by insulation r2 when r1 < rcr.
insulating the pipes. 36
17-6 HEAT TRANSFER FROM FINNED SURFACES
Newton’s law of cooling: The rate of heat transfer
from a surface to the surrounding medium

When Ts and T are fixed, two ways to

increase the rate of heat transfer are
• To increase the convection heat transfer
coefficient h. This may require the
installation of a pump or fan, or replacing
the existing one with a larger one, but this
approach may or may not be practical.
Besides, it may not be adequate.
• To increase the surface area As by
attaching to the surface extended surfaces
called fins made of highly conductive
materials such as aluminum.

37
 The thin plate fins of a car
radiator greatly increase the
rate of heat transfer to the air.

38
Fin Equation

Differential
Volume element of a fin at location x equation
having a length of x, cross-sectional Temperature
area of Ac, and perimeter of p. excess 39
The general solution of the
differential equation

Boundary condition at fin base

1 Infinitely Long Fin

(Tfin tip = T)
Boundary condition at fin tip Boundary conditions at the fin
base and the fin tip.

The variation of temperature along the fin

The steady rate of heat transfer from the entire fin

40
 Under steady conditions, heat
transfer from the exposed surfaces
of the fin is equal to heat conduction
to the fin at the base.
The rate of heat transfer from the fin could also
be determined by considering heat transfer from
a differential volume element of the fin and
integrating it over the entire surface of the fin:

A long circular fin of uniform

cross section and the variation
of temperature along it. 41
2 Negligible Heat Loss from the Fin Tip
(Adiabatic fin tip, Qfin tip = 0)
Fins are not likely to be so long that their temperature approaches the
surrounding temperature at the tip. A more realistic assumption is for
heat transfer from the fin tip to be negligible since the surface area of
the fin tip is usually a negligible fraction of the total fin area.

Boundary condition at fin tip

The variation of temperature along the fin

Heat transfer from the entire fin

42
3 Specified Temperature (Tfin,tip = TL)
In this case the temperature at the end of the fin (the fin tip) is
fixed at a specified temperature TL.
This case could be considered as a generalization of the case of
Infinitely Long Fin where the fin tip temperature was fixed at T.

43
4 Convection from Fin Tip
The fin tips, in practice, are exposed to the surroundings, and thus the proper
boundary condition for the fin tip is convection that may also include the effects
of radiation. Consider the case of convection only at the tip. The condition
at the fin tip can be obtained from an energy balance at the fin tip.

44
A practical way of accounting for the
heat loss from the fin tip is to replace
the fin length L in the relation for the
insulated tip case by a corrected
length defined as

t the thickness of the rectangular fins

D the diameter of the cylindrical fins
Corrected fin length Lc is defined such
that heat transfer from a fin of length Lc
with insulated tip is equal to heat transfer
from the actual fin of length L with
convection at the fin tip. 45
Fin Efficiency

46
Zero thermal resistance or infinite
thermal conductivity (Tfin = Tb)

47
Efficiency of straight fins of rectangular, triangular, and parabolic profiles.

48
Efficiency of annular fins of constant thickness t.

49
50
• Fins with triangular and parabolic profiles contain less material
and are more efficient than the ones with rectangular profiles.
• The fin efficiency decreases with increasing fin length. Why?
• How to choose fin length? Increasing the length of the fin
beyond a certain value cannot be justified unless the added
benefits outweigh the added cost.
• Fin lengths that cause the fin efficiency to drop below 60 percent
usually cannot be justified economically.
51
• The efficiency of most fins used in practice is above 90 percent.
 Fin
Effectiveness

The
effectiveness
of a fin

• The thermal conductivity k of the fin

should be as high as possible. Use
aluminum, copper, iron.
• The ratio of the perimeter to the cross-
sectional area of the fin p/Ac should be
as high as possible. Use slender pin fins.
• Low convection heat transfer coefficient
h. Place fins on gas (air) side.
52
The total rate of heat transfer from a
finned surface

Overall effectiveness for a finned surface

The overall fin effectiveness depends

on the fin density (number of fins per
unit length) as well as the
effectiveness of the individual fins.
The overall effectiveness is a better
measure of the performance of a Various surface areas associated
finned surface than the effectiveness with a rectangular surface with
53
of the individual fins. three fins.
Proper Length of a Fin

mL = 5  an infinitely long fin

Because of the gradual temperature drop mL = 1 offer a good compromise
along the fin, the region near the fin tip makes between heat transfer
little or no contribution to heat transfer. performance and the fin size. 54
A common approximation used in the analysis of fins is to assume the fin
temperature to vary in one direction only (along the fin length) and the
temperature variation along other directions is negligible.
Perhaps you are wondering if this one-dimensional approximation is a
reasonable one.
This is certainly the case for fins made of thin metal sheets such as the fins
on a car radiator, but we wouldn’t be so sure for fins made of thick
materials.
Studies have shown that the error involved in one-dimensional fin analysis
is negligible (less than about 1 percent) when

where  is the characteristic thickness of the fin, which is taken to

be the plate thickness t for rectangular fins and the diameter D for
cylindrical ones.

55
• Heat sinks: Specially
designed finned surfaces
which are commonly used in
the cooling of electronic
equipment, and involve one-
of-a-kind complex
geometries.
• The heat transfer
performance of heat sinks is
usually expressed in terms of
their thermal resistances R.
• A small value of thermal
resistance indicates a small
temperature drop across the
heat sink, and thus a high fin
efficiency.

56
 Summary
• Steady Heat Conduction in Plane Walls
 Thermal Resistance Concept
 Thermal Resistance Network
 Multilayer Plane Walls
• Thermal Contact Resistance
• Generalized Thermal Resistance Networks
• Heat Conduction in Cylinders and Spheres
 Multilayered Cylinders and Spheres
• Critical Radius of Insulation
• Heat Transfer from Finned Surfaces
 Fin Equation
 Fin Efficiency
 Fin Effectiveness
 Proper Length of a Fin

57