Disclosure To Promote The Right To Information
Disclosure To Promote The Right To Information
Scope - Covers the various parameters of the cold coiled compression spring of different sizes for
h’e selection of designer and the user.
I. Terminology - Following symbols and units shall apply (see Fig. 1 ).
Ds = outside coil diameter in mm
d .= wire or rod diameter before coiling into spring in mm
Lo = length of unloaded spring in mm
Fn = spring force correlated to the smallest permissible spring lengthL,(taking into consideration
Sa) in N.
Ln = Lc + Sa = minimum permissible test length in mm
Lc = block length of spring (all coil closed) in mm
S. = sum of the minimum gap between the individual effective coils for spring length Ln in mrr
R = spring rate in N/mm
3. Dimensions and Designation
3.1 Dimensions shall be as given in Table 1.
3.2 Designation - Compression spring with wire dia d = 0.20 mm,outside diameter D, = 2.24 and
ength Lo = 3 mm shall be designated as:
Compression Spring 0.20 X 2.24 X 3 - IS : 7906 (Part 4)
4. Material -Spring steel wire conforming to Grade 2 of IS : 4454 (Part l)-1981 ‘Specification fo
steel wires for cold formed springs: Part 1 Patented and cold drawn steel wires- unalloyed (seconc
*evision)‘, shall be used. If long life is required, superior material to be used.
*PC
P”
1
W
it
In
w-w-w-w
* THEORETICAL
FIG. 1 THEORETICAL COMPRESSION SPRING DIAGRAM
-
(Clause 3.1 I
2
IS:7906(Part 4)-1987
-__--
SI No. De d LO Fll Ltl LC R
mm mm mm N mm mm N/mm
(Continued)
3
IS : 7906 (Part 4) -1987
SI No. De d LO Ffl Ln LC R
mm mm mm N mm mm U/mm
.___
109 22.4 13.33 9.82
110 23.9 15 14.21 10.40
111 25.4 15.00 10.99
4
IS : 7906 ( Part 4 ) -1987
5
IS : 7906 (Part 4)-1987
6
IS : 7906 ( Part 4 ) -1987
332
333
334
1 0.75
9.65
11.18
12.70
22.0
i
5.73
6.52
9.31
4.70
5.16
5.62
5.6
4.72
4.08
(Continued)
7
IS : 7906 (Part 4) -1987
51 I
De LO Ffl Ln LC R
mm mm mm N mm mm N/mm
(Continued )
8
-IS : 7996 ( Part 4 ) -1987
9
IS : 7906 (Part 4) -1987
-I--
“““I
d LO Fll LII Lc R
mm mm N mm mm N/mm
(Continued )
10
IS : 7906 1 Part 4) -1987
(Continued )
11
IS : 7906 (Part 4) -1987
(Continued)
12
IS : 7906 (Part 4) -1987
13
IS -:7906(Part 4)-1987
SI No. D-3 / d LO Fn Ln LC R
mm ~ nm mm N mm mm N/mm
(Continued )
14
IS : 7906 (Part 4) -1987
mm
R
N/mm
(Continued)
15
IS:7906(Part 4)-1987
L-
De d LO Fn Ll7 LC R
1
mm mm mm N mm mm N/mm
~-
767 12.7 6.54 4.76 4.48
768 15.9 7.83 5.27 3.49
769 19.0 9.24 5.62 2.82
770 22.4 10.64 6.37 2.36
771 1.00 25.4 27.6 11.94 6.88 2.05
815
816
_.-
1.30
- 12.70
15.9
55.6 7.52
9.01
6.49
7.27
10.7
8.3.
(Continuea 1
16
IS :7906(Part 4)-1987
I
SI No. De d LO Fi? Lll LC R
mm mm mm N mm mm N/mm
(Continued )
17
IS:7906(Part 4)-1987
- - -- -.--
SI No. d
l-
De LO Fn Ln LC R
I
mm mm mm N mm mm N/mm
i
917 63.5 36.52 26.23 4.05
'918 ,69.8 40.67 28.44 3.66
919 76.2 44.25 30.64 3.35
920 19.0 8.00 5.61 4.03
921 18.29 1.40 22.4 44.5 9.52 6.04 3.50
922 25.4 11.68 6.30 3.24
+ --_
(Continued )
18
IS : 7906 ( Part 4 ) -1987
I d
F
SI No. Fn
,‘:, 1
De LO Ln
mm mm mm N mm N/R,,
!
924 38.1 16.00 8.45 2.01
19
-IS : 7906 ( Part 4 ) -1987
T
-I-
SI No. De d LO Fn Ln LC R
mm mm mm N mm mm N/mm
(Continued)
20
IS : 7906 ( Part 4) -1987
I
1049 51 30.34 19.23 6.7
EXPLANATORY NOTE
This standard is one of the series of standards on design calculation and specifications of helical
coiled springs. Other standards in this series are:
a) IS : 7906 (Part 1 )-I 976 Helical compression springs: Part 1 Design and calculation for springs
made from circular section wire .and bar,
b) IS : 7906 ( Part 2 )-1975 Helical compression springs: Part 2 Specification for cold coiled springs
made from circular section wire and bar,
cl IS : 7906 ( Part 3 )-1975 Helical compression springs: Part 3 Data sheet for springs made from
circular section wire and bar,
4 IS : 7906 (Part 5)-1979 Helical compression springs: Part 5 Hot coiled springs made from
circular section bar,
4 IS : 7906 ( Part 6 )-I 978 Helical compression springs: Part 6 Design and calculation for springs
made from rectangular section bar steel,
f) IS : 7907 (Part 1 )-I975 Helical extension springs: Part 1 Design and calculation for springs
made from circular section wire and bar,
9) IS : 7907 (Part 2)-1976 Helical extension springs: Part 2 Specification for cold coiled springs
made from circular section wire and bar,
h) IS : 7907 ( Part 3)-l 975 Helical extension springs: Part 3 Data sheet for specifications for
springs made from circular section wire and bar, and
j) IS : 7907 (Part 4)-1975 Helical extension springs: Part 4 Selection of standard cold coiled
springs made from circular section wire and bar.
This standard aims at rationalization of various sizes of compression springs eliminating the
unnecessary sizes and retainrng those most commonly used in the industry. This standard is expected
to be of considerable help to the spring designer who can choose the spring required by him from the
list. Some of the most commonly used springs may be available as standard springs from stocks of
spring manufacturers.
21
PrintedatKapoorArtPress,Mayapuri,NewDelhi-110 064.