XM-220 DUAL SPEED MODULE

FIRMWARE REVISION 5

USER MANUAL

1440-SPD02-01RB
Important User Information Solid state equipment has operational characteristics differing from those of
electromechanical equipment. Safety Guidelines for the Application, Installation and
Maintenance of Solid State Controls (Publication SGI-1.1 available from your local
Rockwell Automation sales office or online at
http://www.rockwellautomation.com/literature) describes some important
differences between solid state equipment and hard-wired electromechanical devices.
Because of this difference, and also because of the wide variety of uses for solid state
equipment, all persons responsible for applying this equipment must satisfy
themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or
consequential damages resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes.
Because of the many variables and requirements associated with any particular
installation, Rockwell Automation, Inc. cannot assume responsibility or liability for
actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of
information, circuits, equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written
permission of Rockwell Automation, Inc. is prohibited.
Throughout this manual we use notes to make you aware of safety considerations.

Identifies information about practices or circumstances

WARNING
that can cause an explosion in a hazardous environment,
which may lead to personal injury or death, property
damage, or economic loss.

Identifies information that is critical for successful

IMPORTANT
application and understanding of the product.

Identifies information about practices or circumstances that can

ATTENTION
lead to personal injury or death, property damage, or economic
loss. Attentions help you identify a hazard, avoid a hazard, and
recognize the consequences.

SHOCK HAZARD Labels may be located on or inside the drive to alert

people that dangerous voltage may be present.

BURN HAZARD Labels may be located on or inside the drive to alert

people that surfaces may be dangerous temperatures.

Listen. Think. Solve, Allen-Bradley and XM are trademarks of Rockwell Automation, Inc.
DeviceNet is a trademark of the Open DeviceNet Vendor Association (ODVA).
Microsoft and Windows are registered trademarks of the Microsoft Corporation.

Trademarks not belonging to Rockwell Automation are property of their respective companies.
European Communities (EC) If this product has the CE mark it is approved for installation within the European
Union and EEA regions. It has been designed and tested to meet the following
Directive Compliance directives.

EMC Directive

This product is tested to meet the Council Directive 89/336/EEC Electromagnetic

Compatibility (EMC) by applying the following standards, in whole or in part,
documented in a technical construction file:

• EN 61000-6-4 EMC — Generic Standards, Part 6-4 — Emission

Standard for Industrial Environments (Class A)

• EN 61000-6-2 EMC — Generic Standards, Part 6-2 — Immunity

Standard for Industrial Environment

• EN 61326-6-2 Electromagnetic Equipment for Measurement, Control,

and Laboratory Use — Industrial EMC Requirements

This product is intended for use in an industrial environment.

Low Voltage Directive

This product is tested to meet Council Directive 73/23/EEC Low Voltage by applying
the safety requirements of EN 61131-2 Programmable Controllers, Part 2 —
Equipment Requirements and Tests.

ATEX Directive

This product is certified to meet Council Directive 94/9/EC Equipment and

Protective systems intended for use in Potentially Explosive Atmospheres by applying
standard EN 60079-15 - Electrical apparatus for potentially explosive atmospheres,
Part 15 - Type of protection "n", in whole or in part, documented in a technical
construction file.
 Table of Contents

Chapter 1
Introduction Introducing the XM-220 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
XM-220 Module Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Using this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Organization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 2
Installing the XM-220 Dual Speed XM Installation Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Module Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Grounding Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mounting the Terminal Base Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
DIN Rail Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Interconnecting Terminal Base Units . . . . . . . . . . . . . . . . . . . . . . . 14
Panel/Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connecting Wiring for Your Module . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Terminal Block Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connecting the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connecting the Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting the Buffered Outputs . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connecting the Switched Buffered Output . . . . . . . . . . . . . . . . . . 23
Connecting the 4-20mA Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting the Remote Relay Reset Signal . . . . . . . . . . . . . . . . . . 25
Connecting the Startup Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Connecting the Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Sensor Placement for Reverse Rotation . . . . . . . . . . . . . . . . . . . . . 33
PC Serial Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DeviceNet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Mounting the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Module Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Basic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Powering Up the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Manually Resetting Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Chapter 3
Configuration Parameters Measurement Mode Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Channel Tachometer Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Alarm Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Relay Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4-20mA Output Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
I/O Data Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

v Publication GMSI10-UM004A-EN-E - February 2006

Table of Contents vi

Data Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Monitor Data Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Alarm and Relay Status Parameters . . . . . . . . . . . . . . . . . . . . . . . . 59
Device Mode Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Appendix A
Specifications Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Appendix B
DeviceNet Information Electronic Data Sheets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Changing Operation Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Transition to Program Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Transition to Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
XM Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Invalid Configuration Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
XM-220 I/O Message Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Poll Message Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
COS Message Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
ADR for XM Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Appendix C
DeviceNet Objects Identity Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
DeviceNet Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Assembly Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Connection Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Discrete Input Point Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Parameter Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Acknowledge Handler Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Alarm Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Device Mode Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Relay Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Speed Measurement Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Tachometer Channel Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Transducer Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
4-20mA Output Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Publication GMSI10-UM004A-EN-E - February 2006

 Chapter 1

Introduction

This chapter provides an overview of the XM-220 Dual Speed module. It also
discusses the components of the module.

For information about See page

Introducing the XM-220 Module 1
XM-220 Module Components 2
Using this Manual 3

Introducing the XM-220 The XM-220 Dual Speed module is a member of the Allen-Bradley™ XM®
Module Series, a family of DIN rail mounted condition monitoring and protection
modules that operate both in stand-alone applications or integrate with
Programmable Logic Controllers (PLCs) and control system networks.

The XM-220 is a two channel module that accepts input from any two
tachometers of any standard type including eddy current probes, magnetic
pickups, optical tachometers, and TTL output devices. It measures speed,
rotor acceleration, and peak speed and is capable of detecting zero speed,
locked rotor, and reverse rotation conditions. It is also used as a component of
the XM Electronic Overspeed Detection system.

The XM-220 can be configured (using the configuration software) to operate

in three different modes. This controls how the sensors are used to calculate
the speed, acceleration, and peak measurements.

• Dual Channel Mode - This is the default mode. The two sensors are
used independently to perform two separate sets of speed, acceleration,
and peak speed measurements.

• Single Redundant Channel Mode- One of the two sensors is used

perform the speed, acceleration, and peak speed measurements. The
module automatically switches to the other (redundant) sensor when a
transducer or tachometer fault is detected on the current sensor.

• Reverse Rotation Mode - The two sensors are used to monitor speed
and direction of a single shaft. The two sensors must be mounted out of
phase from each other so that the rotational direction can be determined
by monitoring which sensor the shaft keyway passes first. Refer
to Sensor Placement for Reverse Rotation on page 33.

1 Publication GMSI10-UM004A-EN-E - February 2006

2 Introduction

The module includes a single on-board relay (expandable to five), two 4-20mA
outputs, and a buffered output for each input. A third buffered output is
available when the module is functioning in the single redundant channel
mode. This buffered output signal corresponds to the active input signal so
that the machine speed can be accurately tracked regardless of which of the
redundant sensors is active.

The XM-220 can operate stand-alone, or it can be deployed on a standard or

dedicated DeviceNet network where it can provide real-time data and status
information to other XM modules, PLCs, distributed control systems (DCS),
and Condition Monitoring Systems.

The module can be configured remotely via the DeviceNet network, or locally
using a serial connection to a PC or laptop. Refer to Chapter 3 for a list of the
configuration parameters.

XM-220 Module The XM-220 module consists of a terminal base and an instrument module.
The XM-220 Dual Speed module and the XM-941 Position/Speed Terminal
Components Base are shown below.

Figure 1.1 XM-220 Module Components

DUAL SPEED 1440-SPD02-01RB

XM-941 Speed/Position Module XM-220 Dual Speed Module

Terminal Base Unit Cat. No. 1440-SPD02-01RB
Cat. No. 1440-TB-B

• XM-941 Position/Speed Module Terminal Base - A DIN rail mounted

base unit that provides terminations for all field wiring required by
Position and Speed modules, including the XM-220.

Publication GMSI10-UM004A-EN-E - February 2006

 Introduction 3

• XM-220 Dual Speed Module - Mounts on the XM-941 terminal base

unit via a keyswitch and a 96-pin connector. The XM-220 contains the
measurement electronics, processor, relay, and serial interface port for
local configuration.

IMPORTANT The XM-441 Expansion Relay module may be connected

to the XM-220 module via the XM-941 terminal base unit.
When connected to the XM-220, the Expansion Relay
module simply “expands” the capability of the XM-220 by
adding four additional epoxy-sealed relays. The XM-220
controls the Expansion Relay module by extending to it the
same logic and functional controls as the XM-220 module’s
on-board relay.

Using this Manual This manual introduces you to the XM-220 Dual Speed module. It is intended
for anyone who installs, configures, or uses the XM-220 Dual Speed Module.

Organization

To help you navigate through this manual, it is organized in chapters based on

these tasks and topics.

Chapter 1 “Introduction” contains an overview of this manual and the

XM-220 module.

Chapter 2 “Installing the XM-220 Dual Speed Module” describes how to

install, wire, and use the XM-220 module.

Chapter 3 “Configuration Parameters” provides a complete listing and

description of the XM-220 parameters. The parameters can be viewed and
edited using the XM Serial Configuration Utility software and a personal
computer.

Appendix A “Specifications” lists the technical specifications for the XM-220

module.

Appendix B “DeviceNet Information” provides information to help you

configure the XM-220 over a DeviceNet network.

Appendix C “DeviceNet Objects” provides information on the DeviceNet

objects supported by the XM-220 module.

For definitions of terms used in this Guide, see the Glossary at the end of the
Guide.

Publication GMSI10-UM004A-EN-E - February 2006

4 Introduction

Document Conventions

There are several document conventions used in this manual, including the
following:

The XM-220 module is referred to as XM-220, Speed module, device, or

module throughout this manual.

TIP A tip indicates additional information which may be

helpful.

EXAMPLE This convention presents an example.

Publication GMSI10-UM004A-EN-E - February 2006

 Chapter 2

Installing the XM-220 Dual Speed Module

This chapter discusses how to install and wire the XM-220 Dual Speed
module. It also describes the module indicators and the basic operation of the
module.

For information about See page

XM Installation Requirements 6
Mounting the Terminal Base Unit 12
Connecting Wiring for Your Module 16
Mounting the Module 37
Module Indicators 38
Basic Operations 41

ATTENTION Environment and Enclosure

This equipment is intended for use in a Pollution Degree 2
Industrial environment, in overvoltage Category II applications
(as defined in IED publication 60664–1), at altitudes up to 2000
meters without derating.
This equipment is supplied as “open type” equipment. It must be
mounted within an enclosure that is suitably designed for those
specific environmental conditions that will be present, and
appropriately designed to prevent personal injury resulting from
accessibility to live parts. The interior of the enclosure must be
accessible only by the use of a tool. Subsequent sections of this
publication may contain additional information regarding specific
enclosure type ratings that are required to comply with certain
product safety certifications.
See NEMA Standards publication 250 and IEC publication
60529, as applicable, for explanations of the degrees of
protection provided by different types of enclosures.

5 Publication GMSI10-UM004A-EN-E - February 2006

6 Installing the XM-220 Dual Speed Module

XM Installation This section describes wire, power and grounding requirements, and
instructions for an XM system.
Requirements

Wiring Requirements

Use solid or stranded wire. All wiring should meet the following specifications:

• 12 to 28 AWG copper conductors without pretreatment; 8 AWG

required for grounding the DIN rail for electromagnetic interference
(emi) purposes

• Recommended strip length 8 millimeters (0.31 inches)

• Minimum insulation rating of 300V

• Soldering the conductor is forbidden

• Wire ferrules can be used with stranded conductors; copper ferrules

recommended

ATTENTION See the XM Documentation and Configuration Utility CD

for Hazardous Locations installation drawings. The XM
Documentation and Configuration Utility CD is packaged
with the XM modules.

Power Requirements

Before installing your module, calculate the power requirements of all modules
in each chassis. The total current draw through the side connector cannot
exceed 3A. Refer to the specifications for the specific modules for power
requirements.

ATTENTION A separate power connection is necessary if the total

current draw of the interconnecting modules is greater than
3A.

Figure 2.1 is an illustration of wiring modules using separate power

connections.

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 7

Figure 2.1 XM Modules with Separate Power Connections

1440-VST02-01RA 1440-REX00-04RD 1440-VST02-01RA 1440-REX00-04RD

DYNAMIC MEASUREMENT EXPANSION RELAY DYNAMIC MEASUREMENT EXPANSION RELAY

Power
Supply

1440-RMA00-04RC 1440-REX00-04RD 1440-TSP02-01RB 1440-REX00-04RD

MASTER RELAY EXPANSION RELAY POSITION EXPANSION RELAY

Grounding Requirements

Use these grounding requirements to ensure safe electrical operating

circumstances, and to help avoid potential emi and ground noise that can cause
unfavorable operating conditions for your XM system.

DIN Rail Grounding

The XM modules make a chassis ground connection through the DIN rail.
The DIN rail must be connected to a ground bus or grounding electrode
conductor using 8 AWG or 1 inch copper braid. See Figure 2.2.

Use zinc-plated, yellow-chromated steel DIN rail (Allen-Bradley part no.

199-DR1 or 199-DR4) or equivalent to assure proper grounding. Using other
DIN rail materials (e.g. aluminum, plastic, etc.), which can corrode, oxidize, or
are poor conductors can result in improper or intermittent platform
grounding.

Publication GMSI10-UM004A-EN-E - February 2006

8 Installing the XM-220 Dual Speed Module

Figure 2.2 XM System DIN Rail Grounding

1 DYNAMIC MEASUREMENT
1440-VST02-01RA
EXPANSION RELAY
1440-REX00-04RD
DYNAMIC MEASUREMENT
1440-VST02-01RA
EXPANSION RELAY
1440-REX00-04RD

Power
Supply

1440-RMA00-04RC 1440-REX00-04RD 1440-TSP02-01RB 1440-REX00-04RD

MASTER RELAY EXPANSION RELAY POSITION EXPANSION RELAY

1 DYNAMIC MEASUREMENT
1440-VST02-01RA
EXPANSION RELAY
1440-REX00-04RD
DYNAMIC MEASUREMENT
1440-VST02-01RA
EXPANSION RELAY
1440-REX00-04RD

Power
Supply

1 Use 14 AWG wire. If it is desired to isolate the power supply because of possible ground loops, do not connect
24V Common to earth as illustrated in Figure 2.2. When the 24V supply is isolated from earth, it is
recommended to use an isolator on the RS-232 lines. Refer to PC Serial Port Connection on page 34.

The grounding wire can be connected to the DIN rail using a DIN Rail
Grounding Block (Figure 2.3).

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 9

Figure 2.3 DIN Rail Grounding Block

Panel/Wall Mount Grounding

The XM modules can also be mounted to a conductive mounting plate that is

grounded. See Figure 2.5. Use the grounding screw hole provided on the
terminal base to connect the mounting plate the Chassis terminals.

Figure 2.4 Grounding Screw on XM Terminal Base

Publication GMSI10-UM004A-EN-E - February 2006

10 Installing the XM-220 Dual Speed Module

Figure 2.5 Panel/Wall Mount Grounding

1
Power
Supply

Power
Supply

1 Use 14 AWG wire. If it is desired to isolate the power supply because of possible ground loops, do not connect
24V Common to earth as illustrated in Figure 2.2. When the 24V supply is isolated from earth, it is
recommended to use an isolator on the RS-232 lines. Refer to PC Serial Port Connection on page 34.

24V Common Grounding

It is recommended that all 24V power to the XM modules is grounded. When

two or more power supplies power the XM system, ground the 24V Commons
at a single point, such as the ground bus bar.

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 11

For applications where redundant power supplies are used, only one power
supply needs to be grounded. The XM module ties the two 24V Common
lines together.

IMPORTANT The 24V Common and Signal Common terminals are

internally connected. They are isolated from the Chassis
terminals unless they are connected to ground as described
in this section. See Terminal Block Assignments on page 16
for more information.

Transducer Grounding

Make certain the transducers are electrically isolated from earth ground. Cable
shields must be grounded at one end of the cable, and the other end left
floating or not connected. It is recommended that where possible, the cable
shield be grounded at the XM terminal base (Chassis terminal) and not at the
transducer.

DeviceNet Grounding

The DeviceNet network is isolated and must be referenced to earth ground at

a single point. XM modules do not require an external DeviceNet power
supply. In an XM-only system installation, connect DeviceNet V- to earth
ground at one of the XM modules, as shown in Figure 2.6.

Figure 2.6 Grounded DeviceNet V- at XM Module

To
Ground
Bus

In a system installation in which other DeviceNet products and a separate

DeviceNet power supply are present, the earth ground connection should be
made at the DeviceNet power supply and not at the XM module. See Figure
2.7.

Publication GMSI10-UM004A-EN-E - February 2006

12 Installing the XM-220 Dual Speed Module

Figure 2.7 Grounded DeviceNet V- at DeviceNet Power Supply

DNet
Power
Supply

V- V+
DNet Power V+

DNet Power V-

For more information on the DeviceNet installation, refer to the ODVA

Planning and Installation Manual - DeviceNet Cable System, which is available
on the ODVA web site (http://www.odva.org).

Switch Input Grounding

The Switch Input circuits are electrically isolated from other circuits. It is
recommended that the Switch RTN signal be grounded at a single point.
Connect the Switch RTN signal to the XM terminal base (Chassis terminal) or
directly to the DIN rail, or ground the signal at the switch or other equipment
that is wired to the switch.

Mounting the Terminal The XM family includes several different terminal base units to serve all of the
measurement modules. The XM-941 terminal base, Cat. No. 1440-TB-B, is the
Base Unit only terminal base unit used with the XM-220.

The terminal base can be DIN rail or wall/panel mounted. Refer to the
specific method of mounting below.

ATTENTION The XM modules make a chassis ground connection

through the DIN rail. Use zinc plated, yellow chromated
steel DIN rail to assure proper grounding. Using other
DIN rail materials (e.g. aluminum, plastic, etc.), which can
corrode, oxidize or are poor conductors can result in
improper or intermittent platform grounding.
You can also mount the terminal base to a grounded
mounting plate. Refer to Panel/Wall Mount Grounding on
page 9.

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 13

DIN Rail Mounting

Use the steps below to mount the XM-941 terminal base unit on a DIN rail
(A-B pt no. 199-DR1 or 199-DR4).

1. Position the terminal base on the 35 x 7.5mm DIN rail (A).

Position terminal base at a slight angle and hook over the top of the DIN rail.

2. Slide the terminal base unit over leaving room for the side
connector (B).

3. Rotate the terminal base onto the DIN rail with the top of the rail
hooked under the lip on the rear of the terminal base.

Publication GMSI10-UM004A-EN-E - February 2006

14 Installing the XM-220 Dual Speed Module

4. Press down on the terminal base unit to lock the terminal base on the
DIN rail. If the terminal base does not lock into place, use a screwdriver
or similar device to open the locking tab, press down on the terminal
base until flush with the DIN rail and release the locking tab to lock the
base in place.

Interconnecting Terminal Base Units

Follow the steps below to install another terminal base unit on the DIN rail.

IMPORTANT Make certain you install the terminal base units in order of
left to right.

1. Position the terminal base on the 35 x 7.5mm DIN rail (A).

2. Make certain the side connector (B) is fully retracted into the base unit.

3. Slide the terminal base unit over tight against the neighboring terminal
base. Make sure the hook on the terminal base slides under the edge of
the terminal base unit.

4. Press down on the terminal base unit to lock the terminal base on the
DIN rail. If the terminal base does not lock into place, use a screwdriver
or similar device to open the locking tab, press down on the terminal
base until flush with the DIN rail and release the locking tab to lock the
base in place.

5. Gently push the side connector into the side of the neighboring terminal
base unit to complete the backplane connection.

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 15

Panel/Wall Mounting

Installation on a wall or panel consists of:

• laying out the drilling points on the wall or panel

• drilling the pilot holes for the mounting screws
• installing the terminal base units and securing them to the wall or panel

Use the following steps to install the terminal base on a wall or panel.

1. Lay out the required points on the wall/panel as shown in the drilling
dimension drawing below.

Side Connector

2. Drill the necessary holes for the #6 self-tapping mounting screws.

3. Secure the terminal base unit using two #6 self-tapping screws.

4. To install another terminal base unit, retract the side connector into the
base unit. Make sure it is fully retracted.

5. Position the terminal base unit up tight against the neighboring terminal
base. Make sure the hook on the terminal base slides under the edge of
the terminal base unit.

6. Gently push the side connector into the side of the neighboring terminal
base to complete the backplane connection.

7. Secure the terminal base to the wall with two #6 self-tapping screws.

Publication GMSI10-UM004A-EN-E - February 2006

16 Installing the XM-220 Dual Speed Module

Connecting Wiring for Your Wiring to the module is made through the terminal base unit on which the
module mounts. The XM-220 is compatible only with the XM-941 terminal
Module base unit, Cat. No. 1440-TB-B.

Figure 2.8 XM-941 Terminal Base Unit

XM-941, Cat. No. 1440-TB-B

Terminal Block Assignments

The terminal block assignments and descriptions for the XM-220 module are
shown below.

ATTENTION The terminal block assignments are different for different

XM modules. The following table applies only to the
XM-220. Refer to the installation instructions for the
specific XM module for its terminal assignments.

WARNING
EXPLOSION HAZARD
Do not disconnect equipment unless power has been
removed or the area is known to be nonhazardous.
Do not disconnect connections to this equipment unless
power has been removed or the area is known to be
nonhazardous. Secure any external connections that mate
to this equipment by using screws, sliding latches, threaded
connectors, or other means provided with this product.

Terminal Block Assignments

No. Name Description

0 Xducer 1 (+) Transducer 1 connection
1 Xducer 2 (+) Transducer 2 connection
2 Buffer 1 (+) Signal 1 buffered output
3 Buffer 2 (+) Signal 2 buffered output
4 Switched Buffer (+) Switched buffered output for use with redundant mode

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 17

Terminal Block Assignments

No. Name Description

5 Buffer Power 1 IN Channel 1 buffer power input
Connect to terminal 6 for positive biased transducers or terminal 21 for
negative biased transducers
6 Positive Buffer Bias Provides positive (-5V to +24V) voltage compliance to buffered outputs
Connect to terminals 5 (CH 1) and 22 (CH 2) for positive bias transducers
7 TxD PC serial port, transmit data
8 RxD PC serial port, receive data
9 XRTN1 Circuit return for TxD and RxD
10 Chassis Connection to DIN rail ground spring or panel mounting hole
11 4-20mA 1 (+) 4-20mA output
300 ohm maximum load
12 4-20mA 1 (-)
13 Chassis Connection to DIN rail ground spring or panel mounting hole
14 Chassis Connection to DIN rail ground spring or panel mounting hole
15 Chassis Connection to DIN rail ground spring or panel mounting hole
16 Xducer 1 (-)1 Transducer 1 connection
17 Xducer 2 (-)1 Transducer 2 connection
18 Buffer Common1 Buffered output return
19 Overspeed/Circuit Overspeed and circuit fault output signal
Fault Used as input by the EODS Relay module
20 Switched Buffer (-) Switched buffered output for use with redundant mode (inverted signal)
21 Buffer/Xducer Pwr (-) Provides negative (-24V to +9V) voltage compliance to buffered outputs
Connect to terminals 5 (CH 1) and 22 (CH 2) for negative bias transducers
Transducer power supply output, negative side; used to power external
sensors (40mA maximum load)
22 Buffer Power 2 IN Channel 2 buffer power input
Connect to terminal 6 for positive biased transducers or terminal 21 for
negative biased transducers
23 CAN_High DeviceNet bus connection, high differential (white wire)
24 CAN_Low DeviceNet bus connection, low differential (blue wire)
25 +24V Out Internally connected to 24V In 1 (terminal 44)
Used to daisy chain power if XM modules are not plugged into each other
26 DNet V (+) DeviceNet bus power input, positive side (red wire)
27 DNet V (-) DeviceNet bus power input, negative side (black wire)
28 24V Common1 Internally connected to 24V Common (terminals 43 and 45)
Used to daisy chain power if XM modules are not plugged into each other
If power is not present on terminal 44, there is no power on this terminal
29 4-20mA 2 (+) 4-20mA output
300 ohm maximum load
30 4-20mA 2 (-)
31 Chassis Connection to DIN rail ground spring or panel mounting hole

Publication GMSI10-UM004A-EN-E - February 2006

18 Installing the XM-220 Dual Speed Module

Terminal Block Assignments

No. Name Description

32 Chassis Connection to DIN rail ground spring or panel mounting hole
33 Chassis Connection to DIN rail ground spring or panel mounting hole
34 Chassis Connection to DIN rail ground spring or panel mounting hole
35 Chassis Connection to DIN rail ground spring or panel mounting hole
36 Chassis Connection to DIN rail ground spring or panel mounting hole
37 Chassis Connection to DIN rail ground spring or panel mounting hole
38 Chassis Connection to DIN rail ground spring or panel mounting hole
39 Start Switch input to activate startup switch (active closed)
40 Switch RTN Switch return for Start and Reset Relay
41 Reset Relay Switch input to reset internal relay (active closed)
42 +24V In 2 Connection to secondary external +24V power supply, positive side
Used when redundant power supplies are required
43 24V Common1 Connection to external +24V power supply, negative side (internally
DC-coupled to circuit ground)
44 +24V In 1 Connection to primary external +24V power supply, positive side
45 24V Common1 Connection to external +24V power supply, negative side (internally
DC-coupled to circuit ground)
46 Relay N.C. 1 Relay Normally Closed contact 1
47 Relay Common 1 Relay Common contact 1
48 Relay N.O. 1 Relay Normally Open contact 1
49 Relay N.O. 2 Relay Normally Open contact 2
50 Relay Common 2 Relay Common contact 2
51 Relay N.C. 2 Relay Normally Closed contact 2
1 Terminals are internally connected and isolated from the Chassis terminals.

Connecting the Power Supply

The power supply to the XM-220 is nominally 24V dc. The XM-220 provides
two 24V dc power supply connections. The connections are electrically
isolated from each other so power interruptions to one connection does not
affect the other connection. This allows you to have a redundant power supply
for systems used in critical applications.

Wire the DC-input power supply to the terminal base unit as shown in
Figure 2.9.

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 19

Figure 2.9 DC Input Power Supply Connections

24V dc
Power +
Supply
-

IMPORTANT The primary 24V dc needs to be wired to terminal 44

(+24V In 1) to provide power to the XM-220 and other
XM modules located on the DIN rail. Terminal 42 (+24
In 2) should be used if a second, or redundant, power
supply is needed. Note that the redundant power supply
provides power only to the XM-220 and not other XM
modules on the DIN rail.

ATTENTION The power connections are different for different XM

modules. Refer to the installation instructions for your
specific XM module for complete wiring information.

Connecting the Relays

The XM-220 has both Normally Open (NO) and Normally Closed (NC) relay
contacts. Normally Open relay contacts close when the control output is
energized. Normally Closed relay contacts open when the control output is
energized.

The alarms associated with the relay and whether the relay is normally
de-energized (non-failsafe) or normally energized (failsafe) depends on the
configuration of the module. Refer to Relay Parameters on page 51 for details.

Publication GMSI10-UM004A-EN-E - February 2006

20 Installing the XM-220 Dual Speed Module

Table 2.1 shows the on-board relay connections for the module.

IMPORTANT All XM relays are double pole. This means that each relay
has two contacts in which each contact operates
independently but identically. The following information
and illustrations show wiring solutions for both contacts;
although, in many applications it may be necessary to wire
only one contact.

TIP The Expansion Relay module may be connected to the

XM-220 to provide additional relays. Refer to the XM-441
Expansion Relay Module User Guide for wiring details.

IMPORTANT The NC/NO terminal descriptions (page 18) correspond

T to a de-energized (unpowered) relay.
When the relay is configured for non-failsafe operation, the
relay is normally de-energized.
When the relay is configured for failsafe operation, the
relay is normally energized, and the behavior of the NC and
NO terminals is inverted.

Table 2.1 Relay Connections for XM-220

Configured for
Failsafe Operation Relay 1 Terminals
Nonalarm Alarm Wire Contacts Contact 1 Contact 2
Closed Opened COM 47 50
NO 48 49
Opened Closed COM 47 50
NC 46 51

Configured for
Non-failsafe Operation Relay 1 Terminals
Nonalarm Alarm Wire Contacts Contact 1 Contact 2
Closed Opened COM 47 50
NC 46 51
Opened Closed COM 47 50
NO 48 49

Figures 2.10 and 2.11 illustrate the behavior of the NC and NO terminals
when the relay is wired for failsafe, alarm or nonalarm condition or
non-failsafe, alarm or nonalarm condition.

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 21

Figure 2.10 Relay Connection - Failsafe, Nonalarm Condition

Non-failsafe, Alarm Condition

Figure 2.11 Relay Connection - Failsafe, Alarm Condition

Non-failsafe, Nonalarm Condition

Alternate Relay Wiring

Figures 2.12 and 2.13 show how to wire both ends of a single external
indicator to the XM terminal base for failsafe, nonalarm or alarm condition or
non-failsafe, nonalarm or alarm condition.

Publication GMSI10-UM004A-EN-E - February 2006

22 Installing the XM-220 Dual Speed Module

Figure 2.12 Relay Connection - Failsafe, Nonalarm Condition

Non-failsafe, Alarm Condition

Figure 2.13 Relay Connection - Failsafe, Alarm Condition

Non-failsafe, Nonalarm Condition

Connecting the Buffered Outputs

The XM-220 provides buffered outputs of all transducer input signals. The
buffered output connections may be used to connect the module to portable
data collectors or other online systems.

Figure 2.14 shows the buffered output connections for the module.

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 23

Figure 2.14 Buffered Output Connections

IMPORTANT The voltage operating range of the buffered outputs must

be configured to coincide with the corresponding
transducer bias range. This operating range is configured by
placing a jumper from terminal 5 (channel 1) and terminal
22 (channel) to either terminal 6 (Positive Buffer Bias) or
terminal 21 (Buffer -), depending on the transducer. See
Table 2.2. The buffered output operating range is
configured independently per channel.
Table 2.2 Configuring Buffered Output Input Range

Transducer Input Range Channel Connect Terminal To Terminal

Negative Bias -24 to +9V 1 5 21
2 22 21
Positive Bias -5 to +24V 1 5 6
2 22 6
Non-Bias -5 to +9V 1 --- ---
2 --- ---

Connecting the Switched Buffered Output

The XM-220 can be configured to automatically switch to a second

(redundant) sensor when a transducer or tachometer fault is detected on the
current sensor. When the module is functioning in redundant mode, it
provides a third buffered output which outputs a signal corresponding to the
active input signal. This allows you to accurately track the machine speed
regardless of which of the redundant sensors is active. The signal from the
switched buffered output is a CMOS (0 to 5 volt) level square-wave.

Publication GMSI10-UM004A-EN-E - February 2006

24 Installing the XM-220 Dual Speed Module

The XM-220 switched buffered output can be connected to as many as 19

XM-12X modules, which includes the XM-120, XM-121, XM-122, and
XM-123 modules. Figure 2.15 shows the switched buffered output connection
to an XM-12X module.

Figure 2.15 Switched Buffered Output

IMPORTANT To invert the input signal, connect a jumper from terminal

20 (Switched Buffer -), instead of terminal 4, on the
XM-220 terminal base to terminal 4 (Tach/Signal In +) on
the XM-12X terminal base.

IMPORTANT Make certain to set the Measurement Mode parameter to

"Single Redundant Channel." Refer to Measurement Mode
Parameter on page 44.

TIP When the Measurement Mode parameter is set to either

"Dual Channel" or "Reverse Rotation," the Switched
Buffer output will correspond to channel 1 input.

Connecting the 4-20mA Outputs

The module includes an isolated 4-20mA per channel output into a maximum
load of 300 ohms. The measurements that the 4-20mA output tracks and the
signal levels that correspond to the 4mA and 20mA are configurable. Refer
to 4-20mA Output Parameters on page 56.

Wire the 4-20mA outputs to the terminal base unit as shown in Figure 2.16.

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 25

Figure 2.16 4-20mA Output Connections

ATTENTION The 4-20mA outputs are electrically isolated from other

circuits. It is recommended that the outputs be grounded at
a single point. Connect the 4-20mA (-) to the XM terminal
base (Chassis terminal) or directly to the DIN rail, or
ground the signal at the other equipment in the 4-20mA
loop.

Connecting the Remote Relay Reset Signal

If you set the module relay to latching and the relay activates, the relay stays
activated even when the condition that caused the alarm has ended. The
remote relay reset signal enables you to reset your module relay remotely after
you have corrected the alarm condition. This includes latched relays in the
Expansion Relay module when it is attached to the XM-220.

TIP If you set a module relay to latching, make sure that any
linked relays, such as relays in an XM-440 Master Relay
Module, are not configured as latching. When both relays
are set to latching, the relay in each module will have to be
independently reset when necessary.

TIP You can discretely reset a relay using the serial or remote
configuration tool.

Wire the Remote Relay Reset Signal to the terminal base unit as shown in
Figure 2.17.

Publication GMSI10-UM004A-EN-E - February 2006

26 Installing the XM-220 Dual Speed Module

Figure 2.17 Remote Relay Reset Signal Connection

ATTENTION The Switch Input circuits are electrically isolated from

other circuits. It is recommended that the Switch RTN
signal be grounded at a signal point. Connect the Switch
RTN signal to the XM terminal base (Chassis terminal) or
directly to the DIN rail, or ground the signal at the switch
or other equipment that is wired to the switch.

A single switch contact can also be shared by multiple XM modules wired in

parallel as shown in Figure 2.18.

ATTENTION The relay reset connections may be different for different

XM modules. Figure 2.18 applies only to the XM-220
module. Refer to the installation instructions for the
module for its terminal assignments.

Figure 2.18 Typical Multiple XM Modules Remote Relay Reset Signal Connection

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 27

Connecting the Startup Switch

You can configure the module to detect a locked rotor condition or inhibit the
tachometer fault alarm status during the start-up period. Wire the Startup
switch to the terminal base unit as shown in Figure 2.19.

Figure 2.19 Startup Switch Connection

ATTENTION The Switch Input circuits are electrically isolated from

other circuits. It is recommended that the Switch RTN
signal be grounded at a signal point. Connect the Switch
RTN signal to the XM terminal base (Chassis terminal) or
directly to the DIN rail, or ground the signal at the switch
or other equipment that is wired to the switch.

Connecting the Transducer

The XM-220 can accept input signals from any Allen-Bradley non-contact
eddy current probe, magnetic pickups, or TTL output devices.

IMPORTANT Active magnetic speed sensors or eddy current probes are

often used on machines where rotational speeds below 250
rpm must be reliably sensed, for example reverse rotation
and zero speed applications. Passive magnetic speed
sensors do not typically generate a suitable signal at slow
shaft rotational speeds. To sense shaft rotation speeds
down to 1 rpm, active magnetic speed sensors or eddy
current probes are required.

Publication GMSI10-UM004A-EN-E - February 2006

28 Installing the XM-220 Dual Speed Module

Connecting a Non-Contact Sensor

The figures below show the wiring of a non-contact eddy current probe to the
terminal base unit.

ATTENTION You may ground the cable shield at either end of the cable.
Do not ground the shield at both ends. Recommended
practice is to ground the cable shield at the terminal base
and not at the transducer. Any convenient Chassis terminal
may be used (see Terminal Block Assignments on page 16.

IMPORTANT The internal transducer power supply is providing power to

the non-contact sensor.

IMPORTANT A jumper from terminal 5 to terminal 21 is required for

channel 1 buffered output. A jumper from terminal 22 to
terminal 21 is required for channel 2 buffered output. Refer
to Configuring Buffered Output Input Range on page 23.

Figure 2.20 Non-contact Sensor to Channel 1 Wiring

TYPICAL WIRING FOR NON-CONTACT SENSOR

TO XM-220 DUAL SPEED MODULE CHANNEL 1

Isolated Sensor Driver

-24
SIG
COM

Shield
Floating

Signal Common
16
Channel 1 Input Signal 0

Shield 37
-24V DC 21 Jumpering terminal
5 5 to terminal 21
configures CH 1 buffer
for -24V to 9V

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 29

Figure 2.21 Non-contact Sensor to Channel 2 Wiring

TYPICAL WIRING FOR NON-CONTACT SENSOR

TO XM-220 DUAL SPEED MODULE CHANNEL 2

Isolated Sensor Driver

-24
SIG
COM

Shield
Floating

Signal Common
17
Channel 2 Input Signal 1

Shield 38
-24V DC 21 Jumpering terminal
22 21 to terminal 22
configures CH 2 buffer
for -24V to 9V

Connecting a Magnetic Pickup Sensor

The figures below show the wiring of a passive magnetic pickup sensor to the
terminal base unit.

IMPORTANT Active magnetic speed sensors or eddy current probes are

often used on machines where rotational speeds below 250
rpm must be reliably sensed, for example reverse rotation
and zero speed applications. Passive magnetic speed
sensors do not typically generate a suitable signal at slow
shaft rotational speeds. To sense shaft rotation speeds
down to 1 rpm, active magnetic speed sensors or eddy
current probes are required.

ATTENTION You may ground the cable shield at either end of the cable.
Do not ground the shield at both ends. Recommended
practice is to ground the cable shield at the terminal base
and not at the transducer. Any convenient Chassis terminal
may be used (see Terminal Block Assignments on page 16).

IMPORTANT The module does not power the sensor. It measures only
the input voltage.

Publication GMSI10-UM004A-EN-E - February 2006

30 Installing the XM-220 Dual Speed Module

IMPORTANT An internal isolated constant current (0.5mA) supply is

provided to detect a cable or transducer fault (short). This
current is enabled with the Enable Bias Current
parameter. Refer to Channel Tachometer Parameters on
page 45.

Figure 2.22 Magnetic Pickup to Channel 1 Wiring

TYPICAL WIRING FOR MAGNETIC PICKUP SENSOR

TO XM-220 DUAL SPEED MODULE CHANNEL 1

Cable shield not

connected at this end

Signal Common
16
Channel 1 Input Signal 0

Shield 37

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 31

Figure 2.23 Magnetic Pickup to Channel 2 Wiring

T Y P IC A L W IR IN G F O R M A G N E T IC P IC K U P S E N S O R
TO XM -220 D U AL SPEED M O DU LE C H AN N EL 1

Cable shield not

connected at this end

Signal Common
17
Channel 2 Input Signal 1

Shield 38

Connecting a TTL Output Device

The figures below show the wiring of a TTL output device to the terminal
base unit.

ATTENTION You may ground the cable shield at either end of the cable.
Do not ground the shield at both ends. Recommended
practice is to ground the cable shield at the terminal base
and not at the transducer. Any convenient Chassis terminal
may be used (see Terminal Block Assignments on page 16).

IMPORTANT The internal transducer power supply is providing power to

the TTL device.

Publication GMSI10-UM004A-EN-E - February 2006

32 Installing the XM-220 Dual Speed Module

Figure 2.24 TTL Output Device to Channel 1 Wiring

TYPICAL WIRING FOR TTL OUTPUT DEVICE

TO XM-220 DUAL SPEED MODULE CHANNEL 1

Cable shield not

connected at this end

Signal Common
16
Channel 1 Input Signal 0

Shield 38

+24V DC 6

Figure 2.25 TTL Output Device to Channel 2 Wiring

TYPICAL WIRING FOR TTL OUTPUT DEVICE

TO XM-220 DUAL SPEED MODULE CHANNEL 2

Cable shield not

connected at this end

Signal Common
17
Channel 2 Input Signal 1

Shield 38

+24V DC 6

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 33

Sensor Placement for Reverse Rotation

The XM-220 module uses two input signals for reverse rotation detection.
Connect the first sensor to Channel 1. Connect the second sensor to Channel
2. Refer to Connecting a Non-Contact Sensor on page 28 for wiring details.

Position the sensors so that:

• The keyway passes Channel 1 sensor before it passes Channel 2 sensor

as the machine rotates in the forward direction, as illustrated in
Figure 2.26.

Figure 2.26 Position of the Sensor

CHANNEL 1 SENSOR

KEY (OR SLOT)

ON SHAFT

DIRECTION
OF ROTATION

CHANNEL 2 SENSOR

• The sensors are more than 10 degrees apart and less than 170 degrees
apart in the direction of forward rotation; 90 degrees is optimum. See
Figure 2.27.

Publication GMSI10-UM004A-EN-E - February 2006

34 Installing the XM-220 Dual Speed Module

Figure 2.27 Spacing of the Sensors

CH 1 SENSOR CH 1 SENSOR CH 1 SENSOR

CH 2 SENSOR
CH 2 SENSOR

YES CH 2 SENSOR

CH 1 SENSOR CH 1 SENSOR CH 1 SENSOR

CH 2 SENSOR
CH 2 SENSOR

NO

CH 2 SENSOR

IMPORTANT Make certain to set the Measurement Mode parameter to

"Reverse Rotation." Refer to Measurement Mode
Parameter on page 44.

PC Serial Port Connection

The XM-220 includes a serial port connection that allows you to connect a PC
to it and configure the module’s parameters. There are two methods of
connecting an external device to the module’s serial port.

• Terminal Base Unit - There are three terminals on the terminal base
unit you can use for the serial port connection. They are TxD, RxD, and
RTN (terminals 7, 8, and 9, respectively). If these three terminals are
wired to a DB-9 female connector, then a standard RS-232 serial cable
with 9-pin (DB-9) connectors can be used to connect the module to a
PC (no null modem is required).

The DB-9 connector should be wired to the terminal block as shown.

XM-220 Terminal Base Unit DB-9 Female Connector

(Cat. No. 1440-TB-A)
TX Terminal (terminal 7) ---------------------- Pin 2 (RD - receive data)
RX Terminal (terminal 8) ---------------------- Pin 3 (TD - transmit data)
RTN Terminal (terminal 9) --------------------- Pin 5 (SG - signal ground)

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 35

• Mini-Connector - The mini-connector is located on the top of the

module, as shown below.

Figure 2.28 Mini-Connector

1440-SPD02-01RB
DUAL SPEED

mini-connector

A special cable (Cat. No. 1440-SCDB9FXM2) is required for this

connection. The connector that inserts into the PC is a DB-9 female
connector, and the connector that inserts into the module is a USB
Mini-B male connector.

WARNING
If you connect or disconnect the serial cable with power
applied to the module or the serial device on the other end
of the cable, an electrical arc can occur. This could cause an
explosion in hazardous location installations. Be sure that
power is removed or the area is nonhazardous before
proceeding.

IMPORTANT If 24V Common is not referenced to earth ground, we

recommend you use an RS-232 isolator, such as Phoenix
PSM-ME-RS232/RS232-P (Cat. No. 1440-ISO-232-24), to
protect both the XM module and the computer.

DeviceNet Connection

The XM-220 includes a DeviceNet™ connection that allows the modules to

communicate with a Programmable Logic Controller (PLC), Distributed
Control System (DCS), or another XM module.

DeviceNet is an open, global, industry-standard communications network

designed to provide an interface through a single cable from a programmable
controller to a smart device such as the XM-220. As multiple XM modules are
interconnected, DeviceNet also serves as the communication bus and protocol
that efficiently transfers data between the XM modules.

Publication GMSI10-UM004A-EN-E - February 2006

36 Installing the XM-220 Dual Speed Module

Connect the DeviceNet cable to the terminal base unit as shown.

Connect To Terminal
Red Wire DNet V+ 26
White Wire CAN High 23
Bare Wire Shield (Chassis) 10
Blue Wire CAN Low 24
Black Wire DNet V- 27

ATTENTION
You must ground the DeviceNet shield at only one
location. Connecting the DeviceNet shield to terminal 10
will ground the DeviceNet shield at the XM module. If you
intend to terminate the shield elsewhere, do not connect
the shield to terminal 10.

ATTENTION The DeviceNet network must also be referenced to earth at

only one location. XM modules do not require an external
DeviceNet power supply. This means that in an XM-only
system installation, connect DNet V- to earth or chassis at
one of the XM modules. In a system in which other
DeviceNet products and a separate DeviceNet power
supply are present, the earth ground connection should be
made at the DeviceNet power supply and not at the XM
module.

ATTENTION The DNet V+ and DNet V- terminals are inputs to the XM

module. Do not attempt to pass DeviceNet power through
the XM terminal base to other non-XM equipment by
connecting to these terminals. Failure to comply may result
in damage to the XM terminal base and/or other
equipment.

IMPORTANT Terminate the DeviceNet network and adhere to the

requirements and instructions in the ODVA Planning and
Installation Manual - DeviceNet Cable System, which is
available on the ODVA web site (http://www.odva.org).

The devices are shipped from the factory with the network node address
(MAC ID) set to 63. The network node address is software settable. You can
use the XM Serial Configuration Utility or RSNetWorx™ for DeviceNet™

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 37

(Version 3.0 or later) to set the network node address. Refer to the appropriate
documentation for details.

IMPORTANT The baud rate for the XM-220 is set by way of "baud
detection" (Autobaud) at power-up.

Mounting the Module The XM-220 mounts on the XM-941 terminal base unit, Cat. No. 1440-TB-B.
We recommend that you mount the module after you have connected the
wiring on the terminal base unit.

ATTENTION The XM-220 module is compatible only with the XM-941

terminal base unit. The keyswitch on the terminal base unit
should be at position 4 for the module.
Do not attempt to install XM-220 modules on other
terminal base units.
Do not change the position of the keyswitch after
wiring the terminal base.

ATTENTION This module is designed so you can remove and insert it

under power. However, when you remove or insert the
module with power applied, I/O attached to the module
can change states due to its input/output signal changing
conditions. Take special care when using this feature.

WARNING
When you insert or remove the module while power is on,
an electrical arc can occur. This could cause an explosion in
hazardous location installations. Be sure that power is
removed or the area is nonhazardous before proceeding.

IMPORTANT Install the overlay slide label to protect serial connector and
electronics when the serial port is not in use.

Publication GMSI10-UM004A-EN-E - February 2006

38 Installing the XM-220 Dual Speed Module

1. Make certain the keyswitch (A) on the terminal base unit (C) is at
position 4 as required for the module.

2. Make certain the side connector (B) is pushed all the way to the left. You
cannot install the module unless the connector is fully extended.

3. Make sure that the pins on the bottom of the module are straight so they
will align properly with the connector in the terminal base unit.

4. Position the module (D) with its alignment bar (E) aligned with the
groove (F) on the terminal base.

5. Press firmly and evenly to seat the module in the terminal base unit. The
module is seated when the latching mechanism (G) is locked into the
module.

6. Repeat the above steps to install the next module in its terminal base.

Module Indicators The XM-220 module has seven LED indicators, which include a module status
(MS) indicator, a network status (NS) indicator, a status indicator for each
channel (CH1 and CH2), an activation indicator for startup, a status indicator
for the Relay, and an indicator (AUX) reserved for future use. The LED
indicators are on top of the module.

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 39

Figure 2.29 LED Indicators

1440-SPD02-01RB
DUAL SPEED

Module Indicators

The following tables describe the states of the LED status indicators.

Module Status (MS) Indicator

Color State Description

No color Off No power applied to the module.
Green Flashing Red Module performing power-up self test.
Flashing Module operating in Program Mode1.
Solid Module operating in Run Mode2.
Red Flashing • Application firmware is invalid or not loaded.
Download firmware to the module.
• Firmware download is currently in progress.
Solid An unrecoverable fault has occurred. The module may
need to be repaired or replaced.

1 Program Mode - Typically this occurs when the module configuration settings are being updated with the XM
Serial Configuration Utility. In Program Mode, the module does not perform its normal functions. The signal
processing/measurement process is stopped, and the status of the alarms is set to the disarm state to prevent
a false alert or danger status.

2 Run Mode - In Run Mode, the module collects measurement data and monitors each vibration measurement
device.

Publication GMSI10-UM004A-EN-E - February 2006

40 Installing the XM-220 Dual Speed Module

Network Status (NS) Indicator

Color State Description

No color Off Module is not online.
• Module is autobauding.
• No power applied to the module, look at Module
Status LED.
Green Flashing Module is online (DeviceNet) but no connections are
currently established.1
Solid Module is online with connections currently
established.
Red Flashing One or more I/O connections are in the timed-out state.
Solid Failed communications (duplicate MAC ID or Bus-off).

1 Normal condition when the module is not a slave to an XM-440, PLC, or other master device.

Channel 1 and Channel 2 Indicators

Color State Description

No color Off • Normal operation within alarm limits on the channel.
• No power applied to the module, look at Module
Status LED.
Yellow Solid An alert level alarm condition exists on the channel
(and no transducer fault, tachometer fault, or danger
level alarm condition exists).
Flashing Tachometer fault (no transducer fault) condition exists
on the channel.
Red Solid A danger level alarm condition exists on the channel
(and no transducer fault or tachometer fault condition
exists).
Flashing A transducer fault condition exists on the channel.

Startup (Start) Indicator

Color State Description

Yellow Off Startup period is not in effect.
Solid Startup period is in effect.
• Module may be inhibiting the Tach Fault alarm status.
• Module may be monitoring for locked rotor
conditions.

Publication GMSI10-UM004A-EN-E - February 2006

 Installing the XM-220 Dual Speed Module 41

Relay Indicator

Color State Description

Red Off On-board relay is not activated.
Solid On-board relay is activated.

Basic Operations Powering Up the Module

The XM-220 performs a self-test at power-up. The self-test includes an LED

test and a device test. During the LED test, the indicators will be turned on
independently and in sequence for approximately 0.25 seconds.

The device test occurs after the LED test. The Module Status (MS) indicator is
used to indicate the status of the device self-test.

MS Indicator State Description

Flashing Red and Green Device self-test is in progress.
Solid Green or Flashing Green Device self-test completed successfully,
and the firmware is valid and running.
Flashing Red Device self-test completed, the hardware is
OK, but the firmware is invalid. Or, the
firmware download is in progress.
Solid Red Unrecoverable fault, hardware failure, or
Boot Loader program may be corrupted.

Refer to Module Indicators on page 38 for more information about the LED
indicators.

Manually Resetting Relays

The XM-220 has an external reset switch located on top of the module, as
shown in Figure 2.30.

Publication GMSI10-UM004A-EN-E - February 2006

42 Installing the XM-220 Dual Speed Module

Figure 2.30 Reset Switch

1440-SPD02-01RB
DUAL SPEED

Press the Reset

Switch to reset the
relays

The switch can be used to reset all latched relays in the module. This includes
the relays in the Expansion Relay Module when it is attached to the XM-220.

IMPORTANT The Reset switch resets the relays only if the input is no
longer in alarm or the condition that caused the alarm is no
longer present.

Publication GMSI10-UM004A-EN-E - February 2006

 Chapter 3

Configuration Parameters

This chapter provides a complete listing and description of the XM-220

parameters. The parameters can be viewed and edited using the XM Serial
Configuration Utility software and a personal computer. If the module is
installed on a DeviceNet network, configuring can also be performed using a
network configuration tool such as RSNetWorx (Version 3.0 or later). Refer to
your configuration tool documentation for instructions on configuring a
device.

For information about See page

Measurement Mode Parameter 44
Channel Tachometer Parameters 45
Alarm Parameters 48
Relay Parameters 51
4-20mA Output Parameters 56
I/O Data Parameters 57
Data Parameters 58
Device Mode Parameters 61

IMPORTANT The appearance and procedure to configure the parameters

may differ in different software.

43 Publication GMSI10-UM004A-EN-E - February 2006

44 Configuration Parameters

Measurement Mode The Measurement Mode parameter controls how the two sensors are used to
calculate the speed, acceleration, and peak measurements. The XM-220
Parameter module operates in three different modes:

• Dual Channel - This is the default mode. The two sensors are used
independently to perform two separate sets of speed, acceleration, and
peak speed measurements.

• Single Redundant Channel - One of the two sensors is used to

perform the speed, acceleration, and peak speed measurements. The
module automatically switches to the other (redundant) sensor when a
transducer or tachometer fault is detected on the current sensor (and
there are no faults on the second sensor).

The Speed, Acceleration, and Peak Speed measurements are measured

only on channel 1. Channel 2 measurements (Speed, Acceleration, and
Peak Speed) are not measured.

• Reverse Rotation - The two sensors are used to monitor both speed
and direction. The two sensors must be mounted out of phase from
each other so that the rotational direction can be determined by
monitoring which sensor the shaft keyway passes first. Refer to Sensor
Placement for Reverse Rotation on page 33.

Channel 1 measures the Speed, Acceleration, and Peak Speed in the

forward direction. Channel 2 measures the Speed, Acceleration, and
Peak Speed in the reverse direction.

Measurement Mode Parameter

Parameter Name Description Values/Comments

Mode Controls how the two sensors are used to calculate Options: Dual Channel
the speed, acceleration, and peak measurements. Single Redundant Channel
See above for more details. Reverse Rotation

Publication GMSI10-UM004A-EN-E - February 2006

 Configuration Parameters 45

Channel Tachometer The Tachometer parameters define the characteristics of the tachometer and
determine the signal processing that will be performed on the tachometer
Parameters signal. There are two instances of the tachometer parameters, one for each
channel.

TIP The Channel LED will flash red when a transducer fault
condition exists on the channel even if you are not using
the channel. You can keep the Channel LED from flashing
red on unused channels by setting the unused channel’s
Fault High and Fault Low to greater than zero and less
than zero, respectively. For example, set Fault High to +18
volts and set Fault Low to -18 volts.

IMPORTANT If you are not using the tachometer channel, set the Pulses
per Revolution to zero. This will disable the tachometer
measurement, and prevent the module from indicating a
tachometer fault.

IMPORTANT In Single Redundant Channel mode and Reverse Rotation

mode, the Pulses Per Revolution must be non-zero for
both channels. Redundancy or reverse rotation detection
will be impossible if either tachometer is disabled.

IMPORTANT In Reverse Rotation mode, the value entered in Pulses Per

Revolution must be equal for both channels. And the value
entered in Speed Multiplier must be the equal for both
channels.

Tachometer Parameters

Parameter Name Description Values/Comments

Name (XM Serial Configuration A descriptive name to help identify the tachometer Maximum 18 characters
only) channel in the XM Serial Configuration Utility.

Publication GMSI10-UM004A-EN-E - February 2006

46 Configuration Parameters

Tachometer Parameters

Parameter Name Description Values/Comments

Controls whether a small amount of current is
XM Configuration EDS File injected into the sensor wiring to help detect XM Configuration EDS File
Utility transducer faults of passive magnetic sensors. Utility
Enable Bias Bias Current Check = Enable Enabled
Current Passive magnetic sensors are unbiased and provide
no inherent fault detection capability. The XM-220 is Clear = Disable Disabled
able to detect an open or short circuit from the input
to the sensor using the resistance of the passive Important: If you are using passive
magnetic sensor and a configurable bias current per magnetic sensors, then you must
channel. To use this feature, the resistance of the enable the bias current if:
magnetic sensor must be a minimum of 350 ohms. In
an open circuit situation, the Transducer DC bias • You want to use auto trigger mode.
measurement will read approximately 18 volts. In a
short circuit situation, the Transducer DC bias will • You want to detect transducer fault
read near 0 volts. Under normal operating conditions, conditions.
the Transducer DC bias can range from 0.12 to 3
volts depending on the sensor DC resistance and
temperature. This DC bias may also vary between
XM-220 devices. It is recommended that the Fault
Low and Fault High be set to 0.2 and 7,
respectively.

The bias current parameter also adjusts the

auto-trigger detection algorithm for passive
magnetic signals.
Fault Low The minimum, or most negative, expected DC Volts
voltage from the transducer.
Note: A DC Bias voltage reading
Fault High The maximum expected DC voltage from the
outside this range constitutes a
transducer.
transducer fault.

Important: If you are using passive

magnet sensors, it is recommended
that the Fault Low and Fault High be
set to 0.2 and 7, respectively. See
Bias Current parameter for details.

Publication GMSI10-UM004A-EN-E - February 2006

 Configuration Parameters 47

Tachometer Parameters

Parameter Name Description Values/Comments

DC Bias Time Constant The time constant used for exponential averaging Seconds
(low pass filtering) of the transducer DC bias
measurement. The corner frequency for the low pass
filter is 1 / (2 x π x DC Bias Time Constant). See
example table below.
Time Constant -3dB Frequency Settling
(seconds) (Hz) (seconds)
1 0.159 2.2
2 0.080 4.4
3 0.053 6.6
4 0.040 8.8
5 0.032 11
6 0.027 13.2
7 0.023 15.4
8 0.020 17.6
9 0.018 19.8
10 0.016 22

Sets the trigger mode. In Auto Trigger mode, the

XM Configuration EDS File minimum signal amplitude for triggering is 2 volts XM Configuration EDS File
Utility peak-to-peak and minimum frequency is 6 CPM (0.1 Utility
Hz). Check = Auto Mode Auto
Auto Trigger Trigger
Mode
In Manual Trigger mode, the value entered in Clear = Manual Manual
Trigger Threshold is used as the trigger point. Mode
Minimum signal amplitude for triggering is 500
millivolts peak-to-peak and minimum frequency is 1
CPM (0.0167 Hz). Important: If you are using Auto
Trigger mode with passive magnetic
sensors, make certain to enable the
Bias Current parameter (see page
46). The bias current parameter
adjusts the auto-trigger detection
algorithm for passive magnetic
signals.
Trigger Hysteresis The amount of hysteresis around the trigger % in Auto Trigger mode
threshold. In Auto Trigger mode, the value entered is Volt in Manual Trigger mode
a percentage of the peak-to-peak input signal. This
value can range from 0 to 50%.

In Manual Trigger mode, the value entered is a

voltage level. The hysteresis voltage is added to or
subtracted from the threshold voltage to determine
the hysteresis range. The minimum value is 0.12
volts.

Publication GMSI10-UM004A-EN-E - February 2006

48 Configuration Parameters

Tachometer Parameters

Parameter Name Description Values/Comments

Trigger Threshold The signal level to be used as the trigger value when Enter a value from +16 to -16 volts dc.
in Manual Trigger mode.
Note: This value is not used in Auto
Trigger mode.
Trigger Slope The input signal slope to be used as the trigger Options: Positive
value. Negative
Pulses per Revolution The number of tachometer signal pulses per Enter zero if you are not using the
revolution of the shaft (number of gear teeth). This tachometer channel to disable the
setting is useful if a proximity probe located over a tachometer measurement.
gear or shaft with a multi-toothed speed sensing
surface is used to generate the input signal. Important: When Mode is set to
either "Single Redundant Channel" or
"Reverse Rotation," the Pulses per
Revolution value must be non-zero for
both Channel 1 and Channel 2.

Important: When Mode is set to

"Reverse Rotation," this value must be
the same for both Channel 1 and
Channel 2.
The input tachometer signal is multiplied by this This value must be greater than zero.
XM Configuration EDS File value to obtain the measured speed.
Utility Important: When Mode is set to
Speed Multiplier Tach "Reverse Rotation," this value must be
Multiplier the same for Channel 1 and Channel 2.

Fault Time-Out The number of seconds the module should wait after Enter a value from 1 to 64 seconds.
the last valid tach pulse before it indicates a
tachometer fault.

Alarm Parameters The Alarm parameters control the operation of the alarms (alert and danger
level) and provide alarm status. The XM-220 provides a total of eight alarms.
Each alarm is permanently associated with a corresponding measurement (for
example, Channel 1 Speed alarm, Channel 2 Acceleration alarm, and so on).
Use the parameters to configure which measurement the alarm is associated
with, as well as the behavior of the alarm.

Alarm Parameters

Parameter Name Description Values/Comments

Alarm (XM Serial Configuration Selects one of the eight XM-220 alarms. Each alarm Options: Channel 1 Speed
Utility only) is associated with a particular measurement. Channel 2 Speed
Channel 1 Acceleration
Channel 2 Acceleration
Channel 1 Zero Speed
Channel 2 Zero Speed
Channel 1 Locked Rotor
Channel 2 Locked Rotor

Publication GMSI10-UM004A-EN-E - February 2006

 Configuration Parameters 49

Alarm Parameters

Parameter Name Description Values/Comments

Name (XM Serial Configuration A descriptive name to identify the alarm in the XM Maximum 18 characters
Utility only) Serial Configuration Utility.
Note: This parameter is not applicable
for Locked Rotor alarms.
Enable Enable/disable the selected alarm.
XM Configuration EDS File
Note: The Alarm Status is set to "Disarm" when the Utility
alarm is disabled.
Check to Enable Enabled
Clear to Disable Disabled

Condition Controls when the alarm should trigger. Options: Greater Than
Less Than
• Greater than - Triggers the alarm when the Inside Range
measurement value is greater than or equal to the Outside Range
Alert and Danger Threshold values.
The Danger Threshold value must be greater than Note: This parameter is not applicable
or equal to the Alert Threshold value for the trigger for Locked Rotor alarms.
to occur.
• Less than - Triggers the alarm when the
measurement value is less than or equal to the
Alert and Danger Threshold values.
The Danger Threshold value must be less than or
equal to the Alert Threshold value for the trigger to
occur.
• Inside range - Triggers the alarm when the
measurement value is equal to or inside the range
of the Alert and Danger Threshold values.
The Danger Threshold (High) value must be less
than or equal to the Alert Threshold (High) value
AND the Danger Threshold (Low) value must be
greater than or equal to the Alert Threshold (Low)
value for the trigger to occur.
• Outside range - Triggers the alarm when the
measurement value is equal to or outside the
range of the Alert and Danger Threshold values.
The Danger Threshold (High) value must be greater
than or equal to the Alert Threshold (High) value,
AND the Danger Threshold (Low) value must be
less than or equal to the Alert Threshold (Low)
value for the trigger to occur.

Publication GMSI10-UM004A-EN-E - February 2006

50 Configuration Parameters

Alarm Parameters

Parameter Name Description Values/Comments

Alert Threshold (High) The threshold value for the alert (alarm) condition. The thresholds shall be specified in
the units of the associated
Important: For Locked Rotor alarms, the Alert measurement (for example, RPM for
Threshold value must be less than or equal to the speed, RPM/min for acceleration).
Danger Threshold value.

Note: This parameter is the greater threshold value

when Condition is set to "Inside Range" or "Outside
Range."
Danger Threshold (High) The threshold value for the danger (shutdown)
condition.

Note: This parameter is the greater threshold value

when Condition is set to "Inside Range" or "Outside
Range."
Alert Threshold (Low) The lesser threshold value for the alert (alarm)
condition.

Note: This parameter is not used when Condition is

set to "Greater Than" or "Less Than."
Danger Threshold (Low) The lesser threshold value for the danger (shutdown)
condition.

Note: This parameter is not used when Condition is

set to "Greater Than" or "Less Than."
Hysteresis The amount that the measured value must fall The hysteresis shall be specified in
(below the threshold) before the alarm condition is the units of the associated
cleared. For example, Alert Threshold = 120 and measurement (for example, RPM for
Hysteresis = 2. The alarm (alert) activates when the speed, RPM/min for acceleration).
measured value is 120 and will not clear until the
measured value is 118. Note: This parameter is not applicable
for Locked Rotor alarms.
Note: The Alert and Danger Thresholds use the
same hysteresis value.

Note: For the Outside Range condition, the

hysteresis value must be less than Alert Threshold
(High) – Alert Threshold (Low).
Alert Period The period of time from startup to when the Locked Enter a value from 1 to 255 seconds.
Rotor Alert Threshold is enforced. The Locked
Rotor Alert alarm is activated if the measured speed Note: This parameter is only
fails to exceed the Alert Threshold value within applicable for Locked Rotor alarms.
this specified time.

Note: The Alert Period value must be less than or

equal to the Danger Period value.
Danger Period The period of time from startup to when the Locked Enter a value from 1 to 255 seconds.
Rotor Danger Threshold is enforced. The Locked
Rotor Danger alarm is activated when the measured Note: This parameter is only
speed fails to exceed the Danger Threshold within applicable for Locked Rotor alarms.
this specified time.

Publication GMSI10-UM004A-EN-E - February 2006

 Configuration Parameters 51

Alarm Parameters

Parameter Name Description Values/Comments

Startup Period The length of time that the tachometer fault is Enter a value from 0 to 1092 minutes,
inhibited after the startup period. The startup period adjustable in increments of 0.1
begins when the startup switch is reopened (push minutes.
button disengaged or toggle switch flipped to off).
Note: This parameter is not applicable
for Locked Rotor alarms.
Inhibit Tachometer Fault Controls whether to inhibit the tachometer fault
during the startup period. XM Configuration EDS File
Utility
During startup, the machine may be turning very Check means inhibit Inhibit Tach
slowly and cause the XM module to detect a tachometer fault Fault
tachometer fault. The Alarm status will state that a
tachometer fault condition exists unless the Clear means do not Do not inhibit
tachometer fault is inhibited. inhibit tachometer
fault

Note: This parameter is not applicable

for Locked Rotor alarms.

Relay Parameters The Relay parameters control the operation of the on-board relay, as well as
the relays on the Expansion Relay (XM-441) module. Use these parameters to
configure which alarm(s) the relay is associated with, as well as the behavior of
the relay.

IMPORTANT A relay can be defined, regardless of whether or not it is

physically present. A non-physical relay is a virtual relay.
When a relay (physical or virtual) activates, the module
sends a Change of State (COS) message to its master,
which acts on the condition as necessary. An XM-440
Master Relay Module can activate its own relays in response
to a relay (physical or virtual) activation at any of its slaves.

Publication GMSI10-UM004A-EN-E - February 2006

52 Configuration Parameters

Relay Parameters

Parameter Name Description Options/Comments

Number (XM Serial Configuration Sets the relay to be configured in the XM Serial Relay Number 1 is the on-board relay.
Utility only) Configuration Utility. Numbers 2 through 5 are either relays
on the Expansion Relay module when
it’s connected to the module or virtual
relays.

Virtual relays are non-physical relays.

Use them when you want the effect of
the relay (monitor alarms, delay, and
change status) but do not need an
actual contact closure. For example, a
PLC or controller monitoring the relay
status.

Note: The Relay Installed parameter

indicates whether a relay is a virtual
relay or a physical relay on a module.
Name (XM Serial Configuration A descriptive name to help identify the relay in the Maximum 18 characters
Utility only) XM Serial Configuration Utility.
Enable Enable/disable the selected relay.
XM Configuration EDS File
Note: The Relay Current Status is set to "Not Utility
Activated" when the relay is disabled. See page 58.
Check to Enable Enabled
Clear to Disable Disabled

Controls whether the relay must be explicitly reset

XM Configuration EDS File after the alarm subsides. XM Configuration EDS File
Utility Utility
Latching Latching Check means Latching
Option latching (relay must
be explicitly reset)
Clear means Nonlatching
non-latching (relay
is reset once the
alarm condition has
passed)

Activation Delay Enter the length of time for which the Activation Enter a value from 0 to 25.5 seconds,
Logic must be true before the relay is activated. This adjustable in increments of 0.1
reduces nuisance alarms caused by external noise seconds.
and/or transient vibration events.
Default is 1 second

Publication GMSI10-UM004A-EN-E - February 2006

 Configuration Parameters 53

Relay Parameters

Parameter Name Description Options/Comments

Sets the relay activation logic. Options: A only
XM Configuration EDS File A or B
Utility • A or B - Relay is activated when either Alarm A or A and B
Activation Logic Logic Alarm B meets or exceeds the selected Alarm
Status condition(s).
• A and B - Relay is activated when both Alarm A
and Alarm B meet or exceed the selected Alarm
Status condition(s).
• A Only - Relay is activated when Alarm A meets
or exceeds the selected Alarm Status
condition(s).
Sets the alarm(s) that the relay will monitor. The Options: Channel 1 Speed
XM Configuration EDS File alarm must be from the same device as the relay. Channel 2 Speed
Utility When the Activation Logic is set to "A and B" or "A Channel 1 Acceleration
Alarm A/B Alarm or B," you can select an alarm in both Alarm A and Channel 2 Acceleration
Identifier Alarm B. The system monitors both alarms. When Channel 1 Zero Speed
A/B the Activation Logic is set to "A Only," you can Channel 2 Zero Speed
select only an alarm in Alarm A. Channel 1 Locked Rotor
Channel 2 Locked Rotor

Note: You can only select an alarm

that is enabled.

Publication GMSI10-UM004A-EN-E - February 2006

54 Configuration Parameters

Relay Parameters

Parameter Name Description Options/Comments

Sets the alarm conditions that will cause the relay to Options: Normal
XM Configuration EDS File activate. You can select more than one. Danger
Utility Xdcr Fault
Alarm Status to Alarm Levels • Normal - The current measurement is not within Tacho Fault
Activate On excess of any alarm thresholds. Alert
• Alert - For Speed, Acceleration and Zero Speed Disarm
alarms, the current measurement is in excess of Module Fault
the alert level threshold(s) but not in excess of the
danger level threshold(s). Check to enable.
For Locked Rotor Alarms, the measured speed is Clear to disable.
less than the Alert Threshold value when the
Alert Period expired. The Alert Period is
measured when from the reception of the startup
signal.
• Danger - For Speed, Acceleration and Zero Speed
alarms, the current measurement is in excess of
the danger level threshold(s).
For Locked Rotor Alarms, the measured speed is
less than the Danger Threshold value when the
Danger Period expired. The Danger Period is
measured from the reception of the startup signal.
• Disarm-The alarm is disabled or the device is in
Program mode.
• Xdcr Fault - The transducer’s DC bias
measurement is outside of the transducer’s Fault
High/Fault Low range.
• Module Fault - Hardware or firmware failure, or
an error has been detected and is preventing
proper operation of the device.
• Tacho Fault - For Speed, Acceleration and Zero
Speed alarms, a required tachometer signal has
not been detected (no transducer fault either),
unless the Inhibit Tachometer Fault is enabled
and the startup period is active.
For Locked Rotor Alarms, a required tachometer
signal has not been detected and the Alert Period
has expired. (The tachometer fault is automatically
inhibited until the Alert Period has expired).
Relay Installed Indicates whether the relay is a physical relay on a
module or a virtual relay. If the relay is a physical XM Configuration EDS File
relay, then you can set the Failsafe parameter. Utility
Check = Physical Installed =
If the relay is a virtual relay, the Failsafe parameter Relay Physical Relay
is not used or it is disabled.
Clear = Virtual Relay Not Installed =
Virtual Relay

Publication GMSI10-UM004A-EN-E - February 2006

 Configuration Parameters 55

Relay Parameters

Parameter Name Description Options/Comments

Determines whether the relay is failsafe or
XM Configuration EDS File non-failsafe. XM Configuration EDS File
Utility Utility
Failsafe operation means that when in alarm, the Check means Failsafe
Failsafe Relay Failsafe
relay contacts are in their "normal," de-energized, or failsafe
Option
"shelf-state" positions. In other words, normally
closed relays are closed in alarm, and normally open Clear means Nonfailsafe
relays are open in alarm. With failsafe operation, a non-failsafe
power failure equals an alarm.

The following are true of a relay in failsafe

operation:
• The relay is energized when power is applied to
the module.
• The relay in a nonalarmed condition has power
applied to the coil.
• In alarm condition, power is removed from the
relay coil, causing the relay to change state.

For non-failsafe operation, the following are true:

• Under nonalarm conditions, the relay closes the
circuit between the common and the N.C.
(normally closed) terminals.
• Under alarm conditions, the relay changes state to
close the circuit between the common and the
N.O. (normally open) terminals.

For failsafe operation, the following are true:

• Under nonalarm (with power applied to the unit)
conditions, the relay closes the circuit between the
common and the N.O. terminals.
• Under alarm or loss-of-power conditions, the relay
changes state to close the circuit between the
common and the N.C. terminals.

Publication GMSI10-UM004A-EN-E - February 2006

56 Configuration Parameters

4-20mA Output Parameters The 4-20mA output parameters define the characteristics of the two 4-20mA
output signals. The parameters are the same for each output.

4-20mA Parameters

Parameter Name Description Options/Comments

Enable Enables/disables the 4-20mA output.
XM Configuration EDS File
Utility
Check to enable Enabled
Clear to disable Disabled

Measurement Sets the type of measurement and the channel that Options: Channel 1 Speed
the 4-20mA output signal will track. Channel 2 Speed
Channel 1 Acceleration
Channel 2 Acceleration
Min Range The measured value associated with the 4mA. RPM for Speed
RPM/min for Acceleration
Max Range The measured value associated with the 20mA.

IMPORTANT Measured values between Min Range and Max Range are
scaled into the range from 4.0 to 20.0 to produce the
output value. The Min Range value does not have to be
less than the Max Range value. If the Min Range value is
greater than the Max Range value, then the output signal
is effectively inverted from the input signal.

IMPORTANT The 4-20mA outputs are either on or off. When they are
on, the 4-20mA outputs overshoot the 4 and 20mA limits
by 10% when the measurement exceeds the minimum and
maximum range. This means the minimum current
produced is 3.6mA and the maximum current produced is
22mA.
When the 4-20mA outputs are off, they produce a current
approximately 2.9mA. The 4-20mA outputs are off under
the following conditions:
• The 4-20mA outputs are set to "Disable" (see Enable
above).
• The module is in Program mode.
• A transducer fault or tachometer fault occurs that affects
the corresponding measurement.

Publication GMSI10-UM004A-EN-E - February 2006

 Configuration Parameters 57

I/O Data Parameters The I/O data parameters are used to configure the content and size of the
DeviceNet I/O Poll response message.

IMPORTANT The XM-220 must be free of Poll connections when

configuring the Poll Output (Poll Response Assembly)
and Poll Size. Any attempt to download the parameters
while a master has established the Poll connection with the
XM-220 will result in error.
To close an existing Poll connection with an XM-440,
switch the XM-440 from Run mode to Program mode.
Refer to Changing Operation Modes on page 69.
To close an existing Poll connection with other master
devices, remove the XM-220 from the scan list or turn off
the master device.

I/O Data Parameters

Parameter Name Description Values/Comments

COS Size (XM Serial The size (number of bytes) of the Change of State The COS Size cannot be changed.
Configuration Utility only) (COS) message.
COS Output (XM Serial The Assembly instance used for the COS message. The COS Output cannot be changed.
Configuration Utility only) The COS message is used to produce the Alarm and Refer to COS Message Format on
Relay status for the module. page 75 for more information.
Poll Size Sets the size (number of bytes) of the Poll response The minimum size is 4 bytes and the
message. Decreasing the maximum size will truncate maximum size is 124 bytes.
data from the end of the Assembly structure.

Important: If you set the Poll Output to "Custom

Assembly," the poll size is automatically set to the
actual size of the customized Poll response.
Sets the Assembly instance used for the Poll Options: Assembly Instance 101
XM Configuration EDS File response message. Each Assembly instance contains Assembly Instance 102
Utility a different arrangement of the Poll data. Assembly Instance 103
Custom Assembly
Poll Output Poll
The Poll response message is used by the XM
Response
module to produce measured values. It can contain Refer to Poll Message Format on
Assembly
up to 31 REAL values for a total of 124 bytes of data. page 73 for more information.
Assembly Instance Table (XM Displays the format of the currently selected COS or The highlighted (yellow) Assembly
Serial Configuration Utility only) Poll Assembly instance. structure bytes are included in the I/O
message.
Custom Assembly (XM Serial Defines a custom data format for the Poll response. You can select up to 20 parameters.
Configuration Utility only) The custom assembly can contain any of the
measurement parameters included in Assembly Refer to Poll Message Format on
instance 101, as well as alarm and relay page 73 for more information.
configuration parameters.

Publication GMSI10-UM004A-EN-E - February 2006

58 Configuration Parameters

Data Parameters The Data parameters are used to view the measured values of the input
channels, as well as to monitor the status of the channels, alarms, and relays.

TIP To view all the data parameters in the XM Serial

Configuration Utility, click the View Data tab.

Monitor Data Parameters

Monitor Data Parameters

Parameter Name Description Values/Comments

Speed Shows the measured speed value. Note: In Single Redundant mode,
Channel 2 Speed, Acceleration and
Acceleration Shows the measured acceleration value.
Peak Speed measurements are not
Shows the measured average DC offset of the measured.
XM Configuration EDS File transducer signal. This value is compared with Fault
Utility High and Fault Low to determine whether the Note: In Reverse Rotation mode,
transducer is working properly. Channel 1 measures the Speed,
Xdcr DC Bias Transducer Acceleration, and Peak Speed in the
Measured forward direction, and Channel 2
DC Bias measures the Speed, Acceleration,
and Peak Speed in the reverse
Peak Speed Shows the greatest measured Speed Value direction.
(positive or negative) since the most recent reset.
Startup Status (EDS File only) Shows whether the startup period is in effect.
Reverse Rotation Status (EDS File Shows the direction of the machine rotation. Options: Forward
only) Reverse

Publication GMSI10-UM004A-EN-E - February 2006

 Configuration Parameters 59

Alarm and Relay Status Parameters

Alarm and Relay Status Parameters

Parameter Name Description Values/Comments

Speed Alarm Status States the current status of the speed alarm. Possible status values:

• Normal - The alarm is enabled, the

device is in Run mode, there is no
transducer fault, and the current
measurement is not within the Alert
Acceleration Alarm Status States the current status of the acceleration alarm
or Danger Threshold value(s).
Zero Speed Alarm Status States the current status of the zero speed alarm. • Alert - The alarm is enabled, the
device is in Run mode, there is no
transducer fault, and the current
measurement is in excess of the
Alert Threshold value(s) but not in
excess of the Danger Threshold
value(s).
• Danger - The alarm is enabled, the
device is in Run mode, there is no
transducer fault, and the current
measurement is in excess of the
Danger Threshold value(s).
• Disarm-The alarm is disabled or the
device is in Program mode.
• Transducer Fault - The alarm is
enabled, the device is in Run mode,
and a transducer’s DC bias is outside
the transducer’s Fault High/Fault
Low range.
• Tachometer Fault - The alarm is
enabled, the device is in Run mode,
a tachometer fault exists, but there
is no transducer fault.
• Module Fault - Hardware or
firmware failure, or an error has
been detected and is preventing
proper operation of the device.

Publication GMSI10-UM004A-EN-E - February 2006

60 Configuration Parameters

Alarm and Relay Status Parameters

Parameter Name Description Values/Comments

Locked Rotor Alarm Status States the current status of the locked rotor alarm. Possible status values:

• Normal - The alarm is enabled, the

device is in Run mode, there is no
transducer fault, and the current
measurement is not within the Alert
or Danger Threshold value(s).
• Alert - The alarm is enabled, the
device is in Run mode, there is no
transducer fault or danger condition,
and the measured speed was less
than the Alert Threshold value
when the Alert Period expired.
• Danger - The alarm is enabled, the
device is in Run mode, there is no
transducer fault, and the measured
speed was less than the Danger
Threshold value when the Danger
Period expired.
• Disarm-The alarm is disabled or the
device is in Program mode.
• Transducer Fault - The alarm is
enabled, the device is in Run mode,
and the transducer’s DC bias is
outside the transducer’s Fault
High/Fault Low range.
• Tachometer Fault - The alarm is
enabled, the device is in Run mode,
a tachometer fault exists, (and no
transducer fault), and the Alert
Period has expired.
• Module Fault - Hardware or
firmware failure, or an error has
been detected and is preventing
proper operation of the device.
Relay Status States the current status of the relay. Possible status values: Activated
Not Activated

Publication GMSI10-UM004A-EN-E - February 2006

 Configuration Parameters 61

Device Mode Parameters The Device Mode parameters are used to control the functions and the
behavior of the device.

IMPORTANT The XM Serial Configuration Utility handles these

parameters automatically and transparently to the user.

Device Mode Parameters

Parameter Name Description Values/Comments

Device Mode Sets the current operation mode of the device. Refer Options: Run Mode
to Changing Operation Modes on page 69 for more Program Mode
information.
Autobaud Enables/disables autobaud. Options: Enabled
Disabled
When autobaud is set to "Enabled," the module will
listen to other devices on the network to determine
the correct baud rate to use for communications.
When autobaud is set to "Disabled," the module
baud rate must be set manually.

Publication GMSI10-UM004A-EN-E - February 2006

62 Configuration Parameters

Publication GMSI10-UM004A-EN-E - February 2006

 Appendix A

Specifications

The Appendix lists the technical specifications for the XM-220 module.

XM-220 Technical Specifications

Product Feature Specification

Communications
DeviceNet Standard DeviceNet protocol for all
functions
NOTE: The XM-220 uses only the DeviceNet
protocol, not power. Module power is provided
independently.
Available Electronic Data Sheet (EDS) file
provides support for most DeviceNet
compliant systems
Baud rate automatically set by bus master
to 125kb, 250kb, 500kb
Configurable I/O Poll Response message
helps optimize space utilization within
scanner input tables.
Selectable Poll Response Assembly
Selectable Poll Response Size
(bytes)

Side Connector All XM measurement and relay modules

include side connectors that allow
interconnecting adjacent modules, thereby
simplifying the external wiring
requirements.
The interconnect provides primary power,
DeviceNet communication, and the circuits
necessary to support expansion modules,
such as the XM-441 Expansion Relay
module.

Serial RS-232 via mini-connector or terminal base

unit
Baud rate fixed at 19200.

NOTE: Local configuration via Serial

Configuration Utility.

63 Publication GMSI10-UM004A-EN-E - February 2006

64 Specifications

XM-220 Technical Specifications

Product Feature Specification

Inputs
2 Tachometer Inputs ±25V (50V maximum peak to peak)
Eddy current transducer signals
Magnetic pickups
TTL output devices

Input Impedance 120k ohms minimum

Speed/Frequency Range 1 to 1,200,000 RPM

0.0167 to 20,000 Hz

Speed Measurement Error 1 to 240 RPM ±0.2 RPM

241 to 12,000 RPM ±2 RPM
12,001 to 20,400 RPM ±5 RPM
20,401 to 120,000 RPM ±20 RPM
120,001 to 360,000 RPM ±50 RPM
360,001 to 1,200,000 RPM ±160 RPM
Outputs
4-20mA Outputs Each output is independently programmed
to represent speed or acceleration, from
either channel.
Two isolated outputs
300 ohm max load

Buffered Outputs 1 active buffer per input channel

Output range configurable by wiring:
-24 to +9V
-5 to +24V
-5 to +9V
Third buffered output available when the
module is configured for single redundant
channel mode. Outputs a CMOS (0 to 5
volts) level square-wave that corresponds
to the active input signal.
Sensor Fault Detection
Eddy Current Transducer Bias voltage is compared with the fault
limits.

Magnetic Pickups A current source is available for biasing

passive magnetic pickups to detect open or
short circuits.
Indicators
7 LEDs Module Status - red/green
Network Status - red/green
Channel 1 Status - yellow/red
Channel 2 Status - yellow/red
Startup -yellow
Relay - red
AUX - reserved for future use
Measured Units
RPM
Direction of Rotation
Acceleration in RPM/Minute

Publication GMSI10-UM004A-EN-E - February 2006

 Specifications 65

XM-220 Technical Specifications

Product Feature Specification

Measured Parameters
Direction Forward
Reverse

Speed

Acceleration

Peak Speed

Gap (or transducer bias voltage)

Measured Units RPM

Direction of Rotation
Acceleration in RPM / Minute
Measurement Modes
Dual Channel Two sensors are used independently to
perform two separate speed, acceleration
and peak speed measurements.

Single Redundant Channel One sensor is used to perform the speed,

acceleration and peak speed
measurements. If the current sensor fails,
the module automatically switches to the
second (redundant) sensor.

Reverse Rotation Two sensors are used to monitor both speed

and direction. The two sensors must be
mounted out of phase from each other so
that the rotational direction can be
determined by monitoring which sensor the
shaft keyway passes first.
Alarms
Number 8 alarms, fixed per channel

Alarm Parameters Alarm and danger pair provided for each of:
Speed
Acceleration
Zero Speed
Locked Rotor

Operators Greater than

Less than
Inside range
Outside range

Hysteresis User configurable in software

Publication GMSI10-UM004A-EN-E - February 2006

66 Specifications

XM-220 Technical Specifications

Product Feature Specification

Relays
Number Single on-board relay, two sets of contacts -
DPDT (2 Form C)
Four additional relays when interconnected
to an XM-441 Expansion Relay module, or
Four virtual relays whose status can be
used by remote Control Systems or the
XM-440 Master Relay module

On-board Relay Rating Maximum Voltage: 120V dc, 125V ac

Maximum Current: 3.5A*
Minimum Current: 0
Maximum Power: 60W, 62.5VA
*Max current is up to 40°C, then derates to 2A at
65°C
Agency Rating:
120V ac @ 0.5A
110V dc @ 0.3A
30V dc @ 1.0A

Failsafe Normally energized (failsafe), or

Normally de-energized (non-fail-safe)

Latching Latching, or
Non-latching

Time Delay 0 to 25.5 seconds, adjustable in 100msec

increments

Voting Logic Single or paired "And" or "Or" logic applied

to any alarm

Reset Local reset switch on top of module

Remote reset switch wired to terminal base
Digital reset command via serial or
DeviceNet interface

Activation On Alarm Status:

Normal
Alert
Danger
Disarm
Transducer fault
Module fault
Tacho fault
Peak Speed Capture The XM-220 retains the value of the highest
speed observed since module power was
cycled or the "peak speed" value was
manually reset.

Publication GMSI10-UM004A-EN-E - February 2006

 Specifications 67

XM-220 Technical Specifications

Product Feature Specification

Non-Volatile Configuration A copy of the module configuration is
retained in non-volatile memory from where
it is loaded upon power up*.

*The configuration stored in non-volatile

memory can be deleted only by a command
sent via the serial interface, using the Serial
Configuration Utility, or via DeviceNet from any
compliant software application.
Power
Module +21.6 to +26.4V dc

Consumption Maximum: 300mA

Typical: 225mA

Heat Production Maximum: 7 Watts (24 BTU/hr)

Typical: 4 Watts (14 BTU/hr)

Transducer 24V dc, user configurable with wiring

Redundant Power: All XM Measurement and

Relay modules support redundant power. Each
module includes redundant power inputs on its
terminal base unit.
Environmental
Operating Temperature -20 to +65°C (-4 to +149°F)

Storage Temperature -40 to +85°C (-40 to +185°F)

Relative Humidity 95% non-condensing

Conformal Coating All printed circuit boards are conformally

coated in accordance with IPC-A-610C.
Physical
Dimensions Height: 3.8in (97mm)
Width: 3.7in (94mm)
Depth: 3.7in (94mm)

Terminal Screw Torque 7 pound-inches (0.6Nm)

Publication GMSI10-UM004A-EN-E - February 2006

68 Specifications

XM-220 Technical Specifications

Product Feature Specification

Approvals
(when product or packaging is marked) UL UL Listed for Ordinary
Locations
UL UL Listed for Class I, Division 2
Group A, B, C, and D Hazardous
Locations
CSA CSA Certified Process Control
Equipment
CSA CSA Certified Process Control
Equipment for Class I, Division
2 Group A, B, C, and D
Hazardous Locations
EEX* European Union 94/9/EEC ATEX
Directive, compliant with EN
50021; Potentially Explosive
Atmospheres, Protection “n”
CE* European Union 89/336/EEC
EMC Directive
C-Tick* Australian
Radiocommunications Act,
compliant with:
AS/NZS 2064, Industrial
Emissions

*See the Product Certification link at

www.rockwellautomation.com for Declarations
of Conformity, Certificates and other
certification details.

Publication GMSI10-UM004A-EN-E - February 2006

 Appendix B

DeviceNet Information

Electronic Data Sheets Electronic Data Sheet (EDS) files are simple text files used by network
configuration tools such as RSNetWorx (Version 3.0 or later) to help you
identify products and easily commission them on a network. The EDS files
describe a product’s device type, product revision, and configurable parameters
on a DeviceNet network.

The EDS files for the XM modules are installed on your computer with the
XM configuration software. The latest EDS files can also be obtained at
http://www.ab.com/networks/eds/ or by contacting your local Rockwell
Automation representative.

Refer to your DeviceNet documentation for instructions on registering the

EDS files.

Changing Operation Modes XM modules operate in two modes.

Mode Description
Run The XM measurement modules collect measurement data and
monitor each measurement device.
The XM-440 establishes I/O connections with the XM
measurement modules in its scan list and monitors their alarms,
and controls its own relay outputs accordingly.
Program The XM module is idle.
The XM measurement modules stop the signal
processing/measurement process, and the status of the alarms
is set to the disarm state to prevent a false alert or danger
status.
The XM-440 closes the I/O connections with the XM
measurement modules in its scan list and stops monitoring their
alarms, relays are deactivated unless they are latched.
Configuration parameters can be read, updated and downloaded
to the XM module.

To change the operation mode of the module, use the Device Mode parameter
in the EDS file. Note that the Stop and Start services described on page 71 can
also be used to change the operation mode.

IMPORTANT The XM Serial Configuration Utility software automatically

puts XM modules in Program mode and Run mode
without user interaction.

69 Publication GMSI10-UM004A-EN-E - February 2006

70 DeviceNet Information

Transition to Program Mode

Parameter values can only be downloaded to an XM module while the module

is in Program mode. Any attempt to download a parameter value while the
module is in Run mode will result in a Device State Conflict error.

To transition the XM module from Run mode to Program mode on a

DeviceNet network, set the Device Mode parameter to "Program mode" and
click Apply. Note that you cannot change any other parameter until you have
downloaded the Program mode parameter.

TIP The Module Status indicator flashes green when the

module is in Program model

Refer to your DeviceNet documentation for specific instructions on editing

EDS device parameters.

TIP You can also use the Stop service described on page 71 to
transition XM modules to Program mode.

Transition to Run Mode

In order to collect data and monitor measurement devices, XM modules must

be in Run mode. To transition the XM module from Program mode to Run
mode on a DeviceNet network, set the Device Mode parameter to "Run
mode" and click Apply.

TIP The Module Status indicator is solid green when the

module is in Run mode.

Refer to your DeviceNet documentation for specific instructions on editing

EDS device parameters.

TIP You can also use the Start service described on page 71 to
transition XM modules to Run mode.

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Information 71

XM Services The table below defines services supported by the XM modules. The table
includes the service codes, classes, instances, and attributes by their
appropriate hexadecimal codes. Use the Class Instance Editor in RSNetWorx
to execute these services, as illustrated in the example below.

XM Services

Service Code Class

Action (Hex) (Hex) Instance Attribute Data
Transition to Run Mode Start Device Mode Object 1 None None
(06) (320)
Transition to Program Mode Stop Device Mode Object 1 None None
(07) (320)
Save configuration to Save Device Mode Object 1 None None
non-volatile memory (EEPROM) (16) (320)
Delete saved configuration from Delete Device Mode Object 1 None None
non-volatile memory (EEPROM) (09) (320)
Reset a specific latched relay Reset Relay Object Relay number None None
(05) (323) 1-C for XM-440,
1-5 for XM-12X,
XM-320 and
XM-220, 1-8 for
XM-36X and
XM-16X
Reset all latched relays Reset Relay Object 0 None None
(05) (323)
Reset the Peak Speed (XM-12X Reset Speed Measurement 1, 2 for XM-220 None None
and XM-220 only) (05) Object
(325)
Close the virtual setpoint Other Discrete Input Point 1 None None
multiplier switch to activate the (33) Object
alarm setpoint multipliers (not (08)
applicable to all XM modules)
Open the virtual setpoint Other Discrete Input Point 1 None None
multiplier switch to start the (32) Object
setpoint multiplier timers and (08)
eventually cancel alarm setpoint
multiplication (not applicable to
all XM modules)

Publication GMSI10-UM004A-EN-E - February 2006

72 DeviceNet Information

Example

To save the configuration parameters to the non-volatile memory (EEPROM),

fill in the Class Instance Editor as shown below.

Clear Send the attribute

Select the Save ID and then enter the
service code Class (320 hex) and
Instance (1)
Click Execute to
initiate the
action

Invalid Configuration Errors A Start or Save service request to an XM module may return an Invalid Device
Configuration error when there is a conflict amongst the configuration
settings.

The general error code for the Invalid Device Configuration error is D0hex.
An additional error code is returned with the general error code to specify
which configuration settings are invalid. The table below lists the additional
error codes associated with the Invalid Device Configuration error.

Additional Error Codes returned with the Invalid Device Configuration Error (0xD0)

Error Code
(Hex) Description
01 No specific error information is available.
02 Mismatched transducer, channel, and/or measurement unit.
03 Inverted transducer fault high/low values.
04 Alarm thresholds conflict with the alarm condition.
05 Alarm speed range is invalid.
06 Band minimum frequency is greater than maximum frequency. Or,
maximum frequency is greater than FMAX.
07 Relay is associated with an alarm that is not enabled.
08 Tachometer must be enabled for alarm or channel settings.
09 A senseless speed range is enabled on a speed alarm.

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Information 73

Additional Error Codes returned with the Invalid Device Configuration Error (0xD0)

Error Code
(Hex) Description
0A Too many alarms associated with a single measurement.
0B Invalid node address in the alarm list.
0C Too many alarms in the alarm list. Or, no alarms in the alarm list.
0D Alarm levels cannot be zero for alarms that are enabled.
0E Too many slaves in the scanner’s input data table.
0F The FMAX and Number of Lines do not yield correct vector calculations.
10 Phase (vector) alarms prohibited with synchronous sampling and more
than 1 tachometer pulse per revolution.
11 Can’t have order based band on asynchronous channel.
12 Unsupported Sensor Type and Channel ID combination.
13 Invalid Alarm Type for the associated measurement ID.
14 Synchronous sampling is required for alarm on synchronous
measurements.
15 Integration is not supported with the Bypass High Pass Filter option.

XM-220 I/O Message The XM-220 module supports Poll and Change of State (COS) I/O messages.
Formats The Poll response message is used by the XM modules to produce measured
values, and the COS message is used to produce the Alarm and Relay Status.

Poll Message Format

The XM-220 Poll request message contains no data. The Poll response
message can contain up to 31 REAL values for a total of 124 bytes.

The XM-220 provides three pre-defined (static) data formats of the Poll
response, as defined in Assembly instance 101-103. It also provides a dynamic
Assembly instance, instance 199, with which you can define a custom data
format for the Poll response. The dynamic Assembly instance can contain any
of the measurement parameters included in Assembly instance 101, as well as
several of the alarm and relay configuration parameters.

The default Assembly instance is 101 and the default size is 32 bytes. You can
change the Assembly instance and define the dynamic Assembly using the
configuration software. Refer to I/O Data Parameters on page 57.

The Poll response data can also be requested explicitly through Assembly
Object (Class ID 0x4), Instance 101 (0x65), Data Attribute (3).

Publication GMSI10-UM004A-EN-E - February 2006

74 DeviceNet Information

The following tables show the static data formats of Assembly instances 101–
103.

XM-220 Assembly Instance 101 Data Format

Byte Definition
0–3 Channel 1 Speed measurement value
4–7 Channel 2 Speed measurement value
8–11 Channel 1 Acceleration measurement value
12–15 Channel 2 Acceleration measurement value
16–19 Channel 1 Gap measurement value
20–23 Channel 2 Gap measurement value
24–27 Channel 1 Peak Speed measurement value
28–31 Channel 2 Peak Speed measurement value

XM-220 Assembly Instance 102 Data Format

Byte Definition
0–3 Channel 1 Gap measurement value
4–7 Channel 2 Gap measurement value
8–11 Channel 1 Speed measurement value
12–15 Channel 2 Speed measurement value
16–19 Channel 1 Peak Speed measurement value
20–23 Channel 2 Peak Speed measurement value
24–27 Channel 1 Acceleration measurement value
28–31 Channel 2 Acceleration measurement value

XM-220 Assembly Instance 103 Data Format

Byte Definition
0–3 Channel 1 Speed measurement value
4–7 Channel 1 Acceleration measurement value
8–11 Channel 1 Gap measurement value
12–15 Channel 1 Peak Speed measurement value
16–19 Channel 2 Speed measurement value
20–23 Channel 2 Acceleration measurement value
24–27 Channel 2 Gap measurement value
28–31 Channel 2 Peak Speed measurement value

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Information 75

COS Message Format

The XM-220 COS message contains five bytes of data as defined in the table
below. The COS data can also be requested explicitly through Assembly
Object (Class ID 0x4), Instance 100 (0x64), Data Attribute (3).

XM-220 COS Message Format

Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

0 Relay 1 Startup Period Channel 2 Speed Alarm Status Channel 1 Speed Alarm Status
Status Status (Alarm 2) (Alarm 1)
1 Relay 2 Reverse Channel 2 Acceleration Alarm Status Channel 1 Acceleration Alarm Status
Status Rotation Status (Alarm 4) (Alarm 3)
2 Relay 3 Reserved Channel 2 Zero Speed Alarm Status Channel 1 Zero Speed Alarm Status
Status (Alarm 6) (Alarm 5)
3 Relay 4 Reserved Channel 2 Locked Rotor Alarm Status Channel 1 Locked Rotor Alarm Status
Status
4 Relay 5 Reserved Reserved Reserved
Status

XM Status Values

The following tables describe the XM status values that are included in the
COS messages.

Alarm Status Descriptions

Alarm Status Value Description

0 Normal
1 Alert
2 Danger
3 Disarm
4 Transducer Fault (Sensor OOR)
5 Module Fault
6 Tachometer Fault
7 Reserved

Startup Period Status Descriptions

Startup Period Status Value Description

0 Not Activated
1 Activated

Publication GMSI10-UM004A-EN-E - February 2006

76 DeviceNet Information

Relay Status Descriptions

Relay Status Value Description

0 Not Activated
1 Activated

Reverse Rotation Status Descriptions

Reverse Rotation Status Value Descriptions

0 Forward
1 Reverse

ADR for XM Modules Automatic Device Replacement (ADR) is a feature of an Allen-Bradley

DeviceNet scanner. It provides a means for replacing a failed device with a
new unit, and having the device configuration data set automatically. Upon
replacing a failed device with a new unit, the ADR scanner automatically
downloads the configuration data and sets the node address.

IMPORTANT It is recommended that ADR not be used in safety related

applications. If the failure of the ADR server, and a subse-
quent power cycle, would result in the loss of protection for
a machine, then ADR should not be implemented.

ADR can be used with XM modules but keep the following in mind when
setting up the XM modules.

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Information 77

• The ADR scanner can not download the configuration data to an XM

module if the module has a saved configuration in its non-volatile
memory. This happens because the saved configuration is restored and
the module enters Run mode when the power is cycled. (Configuration
parameters cannot be downloaded while an XM module is in Run
mode.) XM modules must be in Program mode for the ADR
configuration to be downloaded and this occurs only when there is no
saved configuration.

TIP To delete a saved configuration from non-volatile

memory, use the Delete service in RSNetWorx for
DeviceNet or perform the following steps in the XM
Serial Configuration Utility.
1. Save the current configuration to a file. From the
File menu, click Save As and enter a file name for
the configuration.
2. Reset the module to factory defaults. Click the
Module tab and click the Reset button.
3. Reload the saved configuration. From the File
menu, click Open and select the configuration file.
4. Make certain to disable auto save. From the Device
menu, clear the Auto Save Configuration check
mark.

• An XM module will enter Run mode automatically after the ADR

scanner restores the module’s configuration only if the module is in Run
mode at the time the configuration is saved to the scanner. If the
module is in Program mode when the configuration is saved, then the
module will remain in Program mode after the configuration is
downloaded by the ADR scanner.

• The ADR scanner saves and restores only the configuration parameters
contained in the module’s EDS file. Some XM parameters are not
included in the EDS file because they are not supported by either the
EDS specification or the tools that read the EDS files, for example
RSNetWorx for DeviceNet. These configuration parameters will not be
restored with ADR.

Below is a list of the configuration parameters that are not included in

the EDS file and can not be saved or restored with ADR.

– Channel Name
– Tachometer Name
– Alarm Name
– Relay Name
– All Triggered Trend related parameters

Publication GMSI10-UM004A-EN-E - February 2006

78 DeviceNet Information

– All SU/CD Trend related parameters

– Custom Assembly structure (see page 57)

• The ADR and trigger group functions cannot be used together. A

module can have only one primary master so a module cannot be both
configured for ADR and included in a trigger group. The ADR scanner
must be the primary master for the modules configured for ADR. The
XM-440 Master Relay module must be the primary master for modules
included in a trigger group.

Publication GMSI10-UM004A-EN-E - February 2006

 Appendix C

DeviceNet Objects

Appendix C provides information on the DeviceNet objects supported by the

XM-220 module.

For information about See page

Identity Object (Class ID 01H) 80
DeviceNet Object (Class ID 03H) 82
Assembly Object (Class ID 04H) 83
Connection Object (Class ID 05H) 87
Discrete Input Point Object (Class ID 08H) 89
Parameter Object (Class ID 0FH) 90
Acknowledge Handler Object (Class ID 2BH) 95
Alarm Object (Class ID 31DH) 96
Device Mode Object (Class ID 320H) 98
Relay Object (Class ID 323H) 99
Speed Measurement Object (Class ID 325H) 102
Tachometer Channel Object (Class ID 326H) 104
Transducer Object (Class ID 328H) 105
4-20mA Output Object (Class ID 32AH) 107

TIP Refer to the DeviceNet specification for more information

about DeviceNet objects. Information about the
DeviceNet specification is available on the ODVA web site
(http://www.odva.org).

79 Publication GMSI10-UM004A-EN-E - February 2006

80 DeviceNet Objects

Identity Object The Identity Object provides identification and general information about the
device.
(Class ID 01H)

Class Attributes

The Identity Object provides no class attributes.

Instance Attributes

Table C.1 Identity Object Instance Attributes

Access
Attr ID Rule Name Data Type Default Value
1 Get Vendor ID UINT 668 = Entek
2 Get Device Type UINT 109 (Specialty I/O)
3 Get Product Code UINT 35 (0x23)
4 Get Revision: STRUCT OF
Major USINT Value varies with each firmware revision
Minor USINT Value varies with each firmware revision
5 Get Status WORD
6 Get Serial Number UDINT
7 Get Product Name SHORT_ " XM-220 Speed Module"
STRING

Status

The Status is a 16 bit value. The following bits are implemented.

Table C.2 Identity Object Status

Bit Name Description

0 Owned TRUE indicates that the module has an owner. More
specifically, the Predefined Master/Slave Connection Set
has been allocated to a master.
1 Reserved, set to 0
2 Configured This bit is set whenever a saved configuration is
successfully loaded from non-volatile memory. This bit is
cleared whenever the default configuration is restored or
loaded.
3 Reserved, set to 0

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 81

Table C.2 Identity Object Status

Bit Name Description

4 Boot Program Vendor-specific, indicates that the boot program is
running. The Main Application must be corrupt or
missing.
5-7 Vendor-specific, not implemented
8 Minor Recoverable Set whenever there is a transducer or tachometer fault.
Fault
9 Minor Unrecoverable Not implemented
Fault
10 Major Recoverable Set when the module detects a major problem that the
Fault user may be able to recover from. The Module Status
LED will flash red. An example of this condition is when
the boot program is running.
11 Major Unrecoverable Set when there is a module status fault (Module Status
Fault LED is solid red).
12 - 15 Reserved, set to 0

Services

Table C.3 Identity Object Services

Service
Code Class/Instance Usage Name
01h Instance Get_Attributes_All
05h Instance Reset
0Eh Instance Get_Attribute_Single
10h Instance Set_Attribute_Single1

1 Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.

Publication GMSI10-UM004A-EN-E - February 2006

82 DeviceNet Objects

DeviceNet Object The DeviceNet Object is used to provide the configuration and status of a
physical attachment to DeviceNet.
(Class ID 03H)

Class Attributes

Table C.4 DeviceNet Object Class Attributes

Access
Attr ID Rule Name Data Type Default Value
1 Get Revision UINT 2

Instance Attributes

Table C.5 DeviceNet Object Instance Attributes

Access
Attr ID Rule Name Data Type Default Value
1 Get/Set MAC ID1 USINT 63
2 Get/Set Baud Rate2 USINT 0
3 Get Bus-Off Interrupt BOOL 0
4 Get/Set Bus-Off Counter USINT 0
5 Get Allocation Information STRUCT of 0 255
BYTE
USINT
100 Get/Set Autobaud Disable BOOL 0 (Ignore attribute 2 and always autobaud)

1 Setting the MAC ID causes the device to reset automatically, after which it will go online with the new MAC
ID.

2 The Baud Rate setting can not be set while Autobaud Disable is equal to 0. The new baud rate will not take
effect until the module is reset.

The MAC ID, Baud Rate, and Autobaud Disable settings are stored in
non-volatile memory so they do not reset to the default with each power cycle.
The Baud Rate attribute supports the following settings:

• 0 = 125 kbps
• 1 = 250 kbps
• 2 = 500 kbps

The Baud Rate setting is used only when automatic baud rate detection is
disabled (Autobaud Disable = 1). When Autobaud Disable is set to zero
(0), the module ignores its Baud Rate setting and performs automatic baud

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 83

rate detection instead. This means that the module will determine the network
baud rate by listening for network traffic before attempting to go online.

Services

Table C.6 DeviceNet Object Services

Service
Code Class/Instance Usage Name
0Eh Class/Instance Get_Attribute_Single
10h Instance Set_Attribute_Single
4Bh Instance Allocate_Master/Slave_Connetion_Set
4Ch Instance Release_Group_2_Identifier_Set

Assembly Object The Assembly Object binds attributes of multiple objects to allow data to or
from each object to be sent or received in a single message.
(Class ID 04H)
The XM-220 module provide both static and dynamic assemblies.

Class Attribute

Table C.7 Assembly Object Class Attributes

Access
Attr ID Rule Name Data Type Description Semantics
1 Get Revision UINT Revision of the 2
implemented object.

Instances

Table C.8 Assembly Object Instances

Instance Name Type Description

100 Default COS Message Input Alarm and Relay Status values

Publication GMSI10-UM004A-EN-E - February 2006

84 DeviceNet Objects

Table C.8 Assembly Object Instances

Instance Name Type Description

101 Default Poll Response Input Measurement values
Message
102 - 106 Alternate Poll Response Input Measurement values
Message
199 Alternate Dynamic Poll Input User configurable
Response Message measurement values and
configuration parameters

Instance Attributes

Table C.9 Assembly Object Instance Attributes

Access
Attr ID Rule Name Data Type Value
1 Get Number of Members in list UINT Only supported for Dynamic Assembly
instance
2 Set Member List Array of STRUCT: Only supported for Dynamic Assembly
instance
Member Data Description UINT Size of member data value in bits
Member Path Size UINT
Member Path Packed EPATH
3 Get Data Defined in tables
on the following
pages.

Assembly Instance Attribute Data Format

Instance 100 - Alarm and Relay Status

This assembly is sent using COS messaging when any of the Alarm or Relay
Status values change.

Table C.10 Instance 100 Data Format (Alarm and Relay Status Values Assembly)

Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

0 Relay 1 Startup Alarm 2 Status Alarm 1 Status
Status Period (CH 2 Speed Alarm) (CH 1 Speed Alarm)
1 Relay 2 Reverse Alarm 4 Status Alarm 3 Status
Status Rotation (CH2 Acceleration Alarm) (CH1 Acceleration Alarm)

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 85

Table C.10 Instance 100 Data Format (Alarm and Relay Status Values Assembly)

Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

2 Relay 3 0 Alarm 6 Status Alarm 5 Status
Status (CH2 Zero Speed Alarm) (CH1 Zero Speed Alarm)
3 Relay 4 0 Locked Rotor Alarm 2 Status Locked Rotor Alarm 1 Status
Status
4 Relay 5 0 0 0
Status

Instance 101 - Measurement Values

This assembly can be selected to be sent in response to an I/O Poll request

from a master. This assembly is the default Poll response selection.

Table C.11 Instance 101 Data Format (Measurement Values Assembly)

Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

0-3 Channel 1 Speed value
4-7 Channel 2 Speed value
8 - 11 Channel 1 Acceleration value
12 - 15 Channel 2 Acceleration value
16 - 19 Channel 1 Gap value
20 - 23 Channel 2 Gap value
24 - 27 Channel 1 Peak Speed
28 - 31 Channel 2 Peak Speed

Instance 102 - Measurement Values

This assembly can be selected to be sent in response to an I/O Poll request

from a master. This assembly includes all the Gap measurements first.

Table C.12 Instance 102 Data Format (Measurement Values Assembly)

Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

0-3 Channel 1 Gap value
4-7 Channel 2 Gap value
8 - 11 Channel 1 Speed value
12 - 15 Channel 2 Speed value
16 - 19 Channel 1 Peak Speed
20 - 23 Channel 2 Peak Speed
24 - 27 Channel 1 Acceleration value
28 - 31 Channel 2 Acceleration value

Publication GMSI10-UM004A-EN-E - February 2006

86 DeviceNet Objects

Instance 103 - Measurement Values

This assembly can be selected to be sent in response to an I/O Poll request

from a Master. This assembly includes all the Channel 1 measurements first.

Table C.13 Instance 103 Data Format (Measurement Values Assembly)

Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

0-3 Channel 1 Speed value
4-7 Channel 1 Acceleration value
8 - 11 Channel 1 Gap value
12 - 15 Channel 1 Peak Speed
16 - 19 Channel 2 Speed value
20 - 23 Channel 2 Acceleration value
24 - 27 Channel 2 Gap value
28 - 31 Channel 2 Peak Speed

Instance 199 - Dynamic Assembly

This Assembly instance can be created and configured with the XM Serial
Configuration Utility or RSMACC Enterprise Online Configuration Utility.
Using the configuration software, you determine the format of the data. This
assembly instance can be selected to be sent in response to an I/O Poll request
from a Master.

The dynamic Assembly can include all of the measurement values included in
Assembly instance 101. In addition, the dynamic Assembly can include the
following configuration parameters.

Table C.14 Instance 199 Component Mapping

EPATH (where ii = Class Class Instance Attribute Attribute Data

instance number) Name Number Number Name Number Type
21 1D 03 24 ii 30 04 Alarm 31Dh 1-6 Alarm Enable 4 BOOL
21 1D 03 24 ii 30 07 Alarm 31Dh 1-6 Condition 7 USINT
21 1D 03 24 ii 30 08 Alarm 31Dh 1-6 Alert Threshold (High) 8 REAL
21 1D 03 24 ii 30 09 Alarm 31Dh 1-6 Danger Threshold 9 REAL
(High)
21 1D 03 24 ii 30 0A Alarm 31Dh 1-6 Alert Threshold Low 10 REAL
21 1D 03 24 ii 30 0B Alarm 31Dh 1-6 Danger Threshold Low 11 REAL
21 1D 03 24 ii 30 0C Alarm 31Dh 1-6 Hysteresis 12 REAL
21 1D 03 24 ii 30 0E Alarm 31Dh 1-6 Startup Period 14 UINT
21 1D 03 24 ii 30 14 Alarm 31Dh 1-6 Inhibit Tach Fault 20 BOOL

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 87

Table C.14 Instance 199 Component Mapping

EPATH (where ii = Class Class Instance Attribute Attribute Data

instance number) Name Number Number Name Number Type
21 23 03 24 ii 30 04 Relay 323h 1-5 Relay Enable 4 BOOL
21 23 03 24 ii 30 05 Relay 323h 1-5 Latch Enable 5 BOOL
21 23 03 24 ii 30 06 Relay 323h 1-5 Failsafe Enable 6 BOOL
21 23 03 24 ii 30 07 Relay 323h 1-5 Delay 7 UINT
21 23 03 24 ii 30 09 Relay 323h 1-5 Alarm Level 9 BYTE
21 0F 00 24 ii 30 01 Param 0Fh 4-8 Parameter Value 1 USINT
(Alarm Identifier A)
21 0F 00 24 ii 30 01 Param 0Fh 9 - 13 Parameter Value 1 USINT
(Alarm Identifier B)
21 23 03 24 ii 30 0C Relay 323h 1-5 Logic 12 USINT
21 23 03 24 ii 30 0E Relay 323h 1-5 Relay Installed 14 BOOL

The dynamic Assembly instance must be instantiated with a call to the class
level Create service. Then the structure can be defined with the
Set_Attribute_Single service for the Member List attribute. Only one dynamic
Attribute instance is supported so subsequent calls to the Create service will
return a Resource Unavailable (0x02) error. The Delete service can be used to
destroy the dynamic Assembly instance so that it can be re-created.

Services

Table C.15 Assembly Object Services

Service
Code Class/Instance Usage Name
0Eh Class/Instance Get_Attribute_Single
10h Instance Set_Attribute_Single
08h Class Create
09h Instance Delete

Connection Object The Connection Object allocates and manages the internal resources
associated with both I/O and Explicit Messaging Connections.
(Class ID 05H)

Publication GMSI10-UM004A-EN-E - February 2006

88 DeviceNet Objects

Class Attributes

The Connection Object provides no class attributes.

Instances

Table C.16 Assembly Object Instances

Instance Description
1 Explicit Message Connection for pre-defined connection set
2 I/O Poll Connection
4 I/O COS (change of state) Connection
11 - 17 Explicit Message Connection

Instance Attributes

Table C.17 Connection Object Instance Attributes

Access
Attr ID Rule Name Data Type Description
1 Get State USINT State of the object.
2 Get Instance Type USINT Indicates either I/O or Messaging
Connection.
3 Get Transport Class Trigger BYTE Defines behavior of the Connection.
4 Get Produced Connection ID UINT Placed in CAN Identifier Field when the
Connection transmits.
5 Get Consumed Connection UINT CAN Identifier Field value that denotes
ID message to be received.
6 Get Initial Comm BYTE Defines the Message Group(s) across
Characteristics which productions and consumptions
associated with this Connection occur.
7 Get Produced Connection UINT Maximum number of bytes transmitted
Size across this Connection.
8 Get Consumed Connection UINT Maximum number of bytes received across
Size this Connection.
9 Get/Set Expected Packet Rate UINT Defines timing associated with this
Connection.
12 Get/Set Watchdog Time-out USINT Defines how to handle Inactivity/Watchdog
Action timeouts.
13 Get Produced Connection UINT Number of bytes in the
Path Length production_connection_path attribute.

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 89

Table C.17 Connection Object Instance Attributes

Access
Attr ID Rule Name Data Type Description
14 Get Produced Connection Array of Specifies the Application Object(s) whose
Path USINT data is to be produced by this Connection
Object. See DeviceNet Specification
Volume 1 Appendix I.
15 Get Consumed Connection UINT Number of bytes in the
Path Length consumed_connection_path attribute.
16 Get Consumed Connection Array of Specifies the Application Object(s) that are
Path USINT to receive the data consumed by this
Connection Object. See DeviceNet
Specification Volume 1 Appendix I.
17 Get Production Inhibit Time UINT Defines minimum time between new data
production.

Services

Table C.18 Connection Object Services

Service
Code Class/Instance Usage Name
05h Instance Reset
0Eh Instance Get_Attribute_Single
10h Instance Set_Attribute_Single

Discrete Input Point Object The Discrete Input Point Object Instance 1 indicates whether the module is
in the startup period. Instance 2 indicates whether the machine is rotating in
(Class ID 08H) the reverse direction.

Class Attributes

Table C.19 Discrete Input Object Class Attributes

Access
Attr ID Rule Name Data Type Description Semantics
1 Get Revision UINT Revision of the 2
implemented object.

Publication GMSI10-UM004A-EN-E - February 2006

90 DeviceNet Objects

Instance Attributes

Table C.20 Discrete Input Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
3 Get Value BOOL Value 0 = Off
1 = On
199 Set Backdoor USINT Setting this attribute is Set to one of the
Service equivalent to requesting following values to
the specified service. perform the
specified service:
0x32 = Open
0x33 = Close

For instance 1, a Value of 1 means that the startup period is active. For
instance 2, a Value of 1 means that the machine is rotating in the reverse
direction.

Services

Table C.21 Discrete Input Object Services

Service
Code Class/Instance Usage Name Description
0Eh Class/Instance Get_Attribute_Single Returns the contents of the
specified attribute.
10h Instance Set_Attribute_Single Sets the contents of the
specified attribute.
32h Instance Open Opens the virtual Startup
switch.
33h Instance Close Closes the virtual Startup
switch.

The Open and Close services are not valid for Instance 2.

Parameter Object The Parameter Object provides the interface to the XM-220 configuration
data.
(Class ID 0FH)
Parameter Object instance 1 is for the Speed Mode setting (dual channel, single
channel redundant, or reverse rotation). Parameter Object instances 2 to 13
provide an alternate method of setting the configuration parameters with
EPATH data types. And Parameter Object instances 14 and 15 provide an
alternate method of setting the Produced Connection Size and Produced
Connection Path attributes for the Poll Connection because these attributes
can be difficult to get/set directly through the Connection Object.

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 91

Class Attributes

Table C.22 Parameter Object Class Attributes

Access
Attr ID Rule Name Data Type Description Semantics
2 Get Max Instance UINT Maximum instance Total number of parameter
number of an object in object instances.
this class.
8 Get Parameter Class WORD Bits that describe the Bit 0 Supports Parameter
Descriptor parameter. Instances
Bit 1 Supports Full Attrib.
Bit 2 Must do non-volatile store
Bit 3 Params in non-volatile
9 Get Config. UINT Set to 0
Assembly
Instance

Instances

There are 15 instances of this object.

Table C.23 Parameter Object Instances

Read
Instance Only Name Data Type Valid Values Default Value
1 No Mode USINT 0 = Dual Channel 0
1 = Single Channel
Redundant
2 = Reverse Rotation
2 No 4-20mA Output 1 USINT 0 = CH 1 Speed 0
Measurement Identifier 1 = CH 2 Speed
2 = CH 1 Accel
3 = CH 2 Accel
3 No 4-20mA Output 2 USINT 0 = CH 1 Speed 1
Measurement Identifier 1 = CH 2 Speed
2 = CH 1 Accel
3 = CH 2 Accel
4 No Relay 1 Alarm Identifier A USINT 0 = CH 1 Speed Alarm 0
1 = CH 2 Speed Alarm
2 = CH 1 Accel Alarm
3 = CH 2 Accel Alarm
4 = CH 1 Zero Speed Alarm
5 = CH 2 Zero Speed Alarm
6 = CH 1 Locked Rotor Alarm
7 = CH 2 Locked Rotor Alarm

Publication GMSI10-UM004A-EN-E - February 2006

92 DeviceNet Objects

Table C.23 Parameter Object Instances

Read
Instance Only Name Data Type Valid Values Default Value
5 No Relay 2 Alarm Identifier A USINT 0 = CH 1 Speed Alarm 0
1 = CH 2 Speed Alarm
2 = CH 1 Accel Alarm
3 = CH 2 Accel Alarm
4 = CH 1 Zero Speed Alarm
5 = CH 2 Zero Speed Alarm
6 = CH 1 Locked Rotor Alarm
7 = CH 2 Locked Rotor Alarm
6 No Relay 3 Alarm Identifier A USINT 0 = CH 1 Speed Alarm 0
1 = CH 2 Speed Alarm
2 = CH 1 Accel Alarm
3 = CH 2 Accel Alarm
4 = CH 1 Zero Speed Alarm
5 = CH 2 Zero Speed Alarm
6 = CH 1 Locked Rotor Alarm
7 = CH 2 Locked Rotor Alarm
7 No Relay 4 Alarm Identifier A USINT 0 = CH 1 Speed Alarm 0
1 = CH 2 Speed Alarm
2 = CH 1 Accel Alarm
3 = CH 2 Accel Alarm
4 = CH 1 Zero Speed Alarm
5 = CH 2 Zero Speed Alarm
6 = CH 1 Locked Rotor Alarm
7 = CH 2 Locked Rotor Alarm
8 No Relay 5 Alarm Identifier A USINT 0 = CH 1 Speed Alarm 0
1 = CH 2 Speed Alarm
2 = CH 1 Accel Alarm
3 = CH 2 Accel Alarm
4 = CH 1 Zero Speed Alarm
5 = CH 2 Zero Speed Alarm
6 = CH 1 Locked Rotor Alarm
7 = CH 2 Locked Rotor Alarm
9 No Relay 1 Alarm Identifier B USINT 0 = CH 1 Speed Alarm 1
1 = CH 2 Speed Alarm
2 = CH 1 Accel Alarm
3 = CH 2 Accel Alarm
4 = CH 1 Zero Speed Alarm
5 = CH 2 Zero Speed Alarm
6 = CH 1 Locked Rotor Alarm
7 = CH 2 Locked Rotor Alarm
10 No Relay 2 Alarm Identifier B USINT 0 = CH 1 Speed Alarm 1
1 = CH 2 Speed Alarm
2 = CH 1 Accel Alarm
3 = CH 2 Accel Alarm
4 = CH 1 Zero Speed Alarm
5 = CH 2 Zero Speed Alarm
6 = CH 1 Locked Rotor Alarm
7 = CH 2 Locked Rotor Alarm

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 93

Table C.23 Parameter Object Instances

Read
Instance Only Name Data Type Valid Values Default Value
11 No Relay 3 Alarm Identifier B USINT 0 = CH 1 Speed Alarm 1
1 = CH 2 Speed Alarm
2 = CH 1 Accel Alarm
3 = CH 2 Accel Alarm
4 = CH 1 Zero Speed Alarm
5 = CH 2 Zero Speed Alarm
6 = CH 1 Locked Rotor Alarm
7 = CH 2 Locked Rotor Alarm
12 No Relay 4 Alarm Identifier B USINT 0 = CH 1 Speed Alarm 1
1 = CH 2 Speed Alarm
2 = CH 1 Accel Alarm
3 = CH 2 Accel Alarm
4 = CH 1 Zero Speed Alarm
5 = CH 2 Zero Speed Alarm
6 = CH 1 Locked Rotor Alarm
7 = CH 2 Locked Rotor Alarm
13 No Relay 5 Alarm Identifier B USINT 0 = CH 1 Speed Alarm 1
1 = CH 2 Speed Alarm
2 = CH 1 Accel Alarm
3 = CH 2 Accel Alarm
4 = CH 1 Zero Speed Alarm
5 = CH 2 Zero Speed Alarm
6 = CH 1 Locked Rotor Alarm
7 = CH 2 Locked Rotor Alarm
14 No Poll Connection Produced USINT 101 - 103, 199 (Assembly 101
Connection Path1 Object instance number)
15 No Poll Connection Produced UINT 4 -124 32
Connection Size1

1 The Poll Connection Produced Connection Path and Size parameters cannot be set while the Poll connection is
already established with a master/scanner. Attempting to do so will result in an "Object State Conflict" error
(error code 0xC). These Parameter instances are a little more flexible than the actual Connection Object
attributes because they can be set while the connection is in the NON-EXISTENT state (before the
master/scanner allocates the connection).

Publication GMSI10-UM004A-EN-E - February 2006

94 DeviceNet Objects

Instance Attributes

Table C.24 Parameter Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
1 Set Parameter Actual value of parameter See Table C.23 for a list of valid
Value values for each instance.
2 Get Link Path Size USINT Size of Link Path 0 (These Parameter instances do
not link directly to another
object attribute.)
3 Get Link Path ARRAY of DeviceNet path to the
DeviceNet object for the Parameter
path value.
Segment BYTE See DeviceNet
Type/Port Specification Volume 1
Appendix I for format.
Segment See DeviceNet
Address Specification Volume 1
Appendix I for format.
4 Get Descriptor WORD Description of Parameter Bit 0 Settable Path support
Bit 1 Enum Strings support
Bit 2 Scaling support
Bit 3 Scaling Links support
Bit 4 Read only
Bit 5 Monitor
Bit 6 Ext. Prec. scaling
5 Get Data Type EPATH Data Type Code See DeviceNet Specification
Volume 1 Appendix J.
6 Get Data Size USINT Number of Bytes in
Parameter value.

Services

Table C.25 Parameter Object Services

Service
Code Class/Instance Usage Name Description
0Eh Class/Instance Get_Attribute_Single Returns the contents of the
specified attribute.
10h Class Set_Attribute_Single Sets the contents of the
specified attribute.1

1 Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 95

Acknowledge Handler The Acknowledge Handler Object is used to manage the reception of message
acknowledgments. This object communicates with a message producing
Object Application Object within a device. The Acknowledge Handler Object notifies
(Class ID 2BH) the producing application of acknowledge reception, acknowledge timeouts,
and production retry limit errors.

Class Attributes

The Acknowledge Handler Object provides no class attributes.

Instances

A module provides only a single instance (instance 1) of the Acknowledge

Handler Object. This instance is associated with instance 4 of the Connection
Object, the slave COS connection to a higher level master.

Instance Attributes

Table C.26 Acknowledge Handler Object Instance Attributes

Access
Attr ID Rule Name Data Type Default Value
1 Get/Set Acknowledge Timer UINT 16ms
2 Get/Set Retry Limit USINT 1
3 Get COS Producing UINT 4
Connection Instance

Services

Table C.27 Acknowledge Handler Object Services

Service
Code Class/Instance Usage Name
0Eh Instance Get_Attribute_Single
10h Instance Set_Attribute_Single

Publication GMSI10-UM004A-EN-E - February 2006

96 DeviceNet Objects

Alarm Object The Alarm Object models a two-stage (alert and danger levels) alarm.
(Class ID 31DH)
Class Attributes

The Alarm Object provides no class attributes.

Instances

There are 6 instances of this object.

Table C.28 Alarm Object Instances

Instance Measurement
Alarm 1 Channel 1 Speed
Alarm 2 Channel 2 Speed
Alarm 3 Channel 1 Acceleration
Alarm 4 Channel 2 Acceleration
Alarm 5 Channel 1 Zero Speed
Alarm 6 Channel 2 Zero Speed

Instance Attributes

Table C.29 Alarm Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
3 Get Alarm Status 3 BITS The current status of the 0 = Normal
alarm. 1 = Alert (alarm)
2 = Danger (shutdown)
3 = Disarm
4 = Xdcr Fault
5 = Module Fault
6 = Tachometer Fault
4 Get/Set Alarm Enable BOOL Indicates whether this 0 = Disabled
alarm object is enabled. 1 = Enabled
6 Get Threshold Units USINT Indicates whether the Set to 1
threshold and hysteresis 1 = Measurement units
value are specified in
units of measure.
7 Get/Set Condition USINT Indicates on which side of 0 = Greater than
the threshold values the 1 = Less than
alarm and danger 2 = Inside range
conditions exist. 3 = Outside range

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 97

Table C.29 Alarm Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
8 Get/Set Alert Threshold REAL The threshold value for
(High) the alert (alarm) condition
(greater threshold for
range types).
9 Get/Set Danger REAL The threshold value for
Threshold (High) the danger (shutdown)
condition (greater
threshold for range types).
10 Get/Set Alert Threshold REAL The lesser threshold value
Low for the alert (alarm)
condition for the range
condition types.
11 Get/Set Danger REAL The lesser threshold value
Threshold for the danger (shutdown)
Low condition for the range
condition types.
12 Get/Set Hysteresis REAL The amount on the safe
side of a threshold by
which the value must
recover to clear the alarm.
14 Get/Set Startup Period UINT The amount of time that Seconds
the Tach Fault status may
be inhibited after the
startup signal is received.
18 Get/Set Name STRING2 A name to help identify
this alarm.
20 Get/Set Inhibit Tach BOOL Determines whether the 0 = Tach Fault allowed
Fault Tach Fault status is 1 = Tach Fault inhibited
prohibited during the
startup period.

Services

The settable attributes of this object are not affected by the status of the
Device Mode Object.

Table C.30 Alarm Object Services

Service
Code Class/Instance Usage Name Description
0Eh Instance Get_Attribute_Single Returns a single attribute.
10h Instance Set_Attribute_Single Sets a single attribute.1
1 Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.

Publication GMSI10-UM004A-EN-E - February 2006

98 DeviceNet Objects

Device Mode Object The Device Mode Object is used to control access to the configuration
parameters in the module. This object’s Device Mode attribute must be in
(Class ID 320H) PROGRAM mode to allow the module’s configuration parameters to be "Set"
(see Services). Attempts to set the configuration parameters while the Device
Mode is in RUN mode will return an error. Note that the module collects
measurements while in RUN mode but not while it is in PROGRAM mode.

Class Attributes

The Device Mode Object provides no class attributes.

Instance Attributes

Table C.31 Device Mode Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
3 Get/Set Device Mode UINT The operating mode of the 0 = Power Up
module. 1 = RUN
2 = PROGRAM
199 Set Backdoor USINT Setting this attribute is Set to one of the following
Service equivalent to requesting values to perform the specified
the specified service. service:
0x05 = Reset
0x09 = Delete
0x15 = Restore
0x16 = Save

Setting the Device Mode attribute to "1" (RUN) is equivalent to executing the
Start service. Setting the Device Mode attribute to "2" (PROGRAM) is
equivalent to executing the Stop service.

Services

Table C.32 Device Mode Object Services

Service
Code Class/Instance Usage Name Description
0Eh Instance Get_Attribute_Single Return the value of a single
attribute.
10h Instance Set_Attribute_Single Set the value of a single
attribute.
07h Instance Stop Transitions from Run to the
Program state.

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 99

Table C.32 Device Mode Object Services

Service
Code Class/Instance Usage Name Description
06h Instance Start Validate the device
configuration settings and
transition to the Run state if
OK.
05h Instance Reset Transition to the Power Up
state. Load the non-volatile
configuration and transition
to the Run state if saved
configuration restored.
16h Instance Save Validate the device
configuration settings if
necessary and save them to
non-volatile memory.
09h Instance Delete Delete the saved
configuration from
non-volatile memory.
15h Instance Restore Load the saved
configuration or the factory
default configuration from
non-volatile memory.

Relay Object The Relay Object models a relay (actual or virtual). A relay can be activated or
deactivated based on the status of one or more alarms.
(Class ID 323H)

Class Attributes

Table C.33 Relay Object Class Attributes

Access
Attr ID Rule Name Data Type Description Semantics
3 Get Number of UINT Number of Instances in 5
Instances this class.
100 Set Reset All USINT Setting this attribute is Reset All is an attribute that
equivalent to executing provides a way to perform a
the Class Reset service Class level Reset service via the
Set_Attribute_Single service.
Setting this attribute to any
value is equivalent to
performing the Class level Reset
service. Reading the Reset All
attribute always returns zero.

Publication GMSI10-UM004A-EN-E - February 2006

100 DeviceNet Objects

Instances

There are 5 instances of this object.

Instance Attributes

Table C.34 Relay Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
3 Get Relay Status BOOL The current status of the 0 = Off
relay. 1 = On
4 Get/Set Relay Enable BOOL Indicates whether this 0 = Disabled
relay object is enabled. 1 = Enabled
5 Get/Set Latch Enable BOOL Indicates whether this 0 = Nonlatching
relay latches (requires a 1 = Latching
reset command to
deactivate).
6 Get/Set Failsafe Enable BOOL Indicates whether this 0 = Non-failsafe (not normally
relay is normally energized)
energized (activated 1 = Failsafe (normally energized)
during power loss).
7 Get/Set Delay USINT The time period that the 0 to 25.5 seconds
voting logic must be true (specified in tenths of seconds)
before the relay is
activated.
8 Get/Set Name STRING2 A name to help identify 18 characters maximum
the relay.
9 Get/Set Alarm Level BYTE Specifies what alarm 0 = Normal
status values will cause 1 = Alert
the relay to activate. 2 = Danger
3 = Disarm
4 = Xdcr Fault
5 = Module Fault
6 = Tachometer Fault
10 Get/Set Alarm Identifier EPATH Identifies the first alarm See Parameter Object instances
A status the relay monitors. 4 to 8.

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 101

Table C.34 Relay Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
11 Get/Set Alarm Identifier EPATH Identifies the second See Parameter Object instances
B alarm status the relay 9 to 13.
monitors.
12 Get/Set Logic USINT Indicates the number of 0 = Ignore Alarm Identifier B
associated alarms that and activate the relay based on
must have a status value the status of Alarm Identifier
specified by Alarm Level A.
in order to activate the 1 = Activate the relay if the
relay. status of either Alarm
Identifier A or B matches any
of the statuses specified by
Alarm Level.
2 = Activate the relay if the
status of both Alarm Identifier
A and B match any of the
statuses specified by Alarm
Level.
14 Get Relay Installed BOOL Indicates whether an 0 = Not installed
actual relay is associated 1 = Installed
with this instance.

Services

Setting the attributes of this object are not affected by the status of the Device
Mode Object.

Table C.35 Relay Object Services

Service
Code Class/Instance Usage Name Description
05h Class/Instance Reset Resets latched relay(s).
0Eh Class/Instance Get_Attribute_Single Returns a single attribute.
10h Class/Instance Set_Attribute_Single Sets a single attribute.1

1 Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.

Publication GMSI10-UM004A-EN-E - February 2006

102 DeviceNet Objects

Speed Measurement Object The Speed Measurement Object models a speed measurement of a tachometer
signal.
(Class ID 325H)

Class Attributes

The Speed Measurement Object provides no class attributes.

Instances

There are 2 instances of the object.

Instance Attributes

Table C.36 Speed Measurement Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
3 Get Speed Value REAL The measured speed CPM
value.
4 Get Status BOOL Indicates if a fault or 0 = Operating without alarms or
alarm has occurred. faults
1 = Alarm or fault condition
exists. The Speed Value
attribute may not represent the
actual field value.
5 Get Maximum REAL The maximum (peak) CPM
Speed measured speed value
(positive or negative)
since the most recent
reset.
6 Get/Set Locked Rotor BOOL Indicates whether the 0 = Disabled
Alarm Enable locked rotor alarm is 1 = Enabled
enabled.
7 Get Locked Rotor USINT The current status of the 0 = Normal
Alarm Status locked rotor alarm. 1 = Alert (alarm)
2 = Danger (shutdown)
3 = Disarm
4 = Xdcr Fault
5 = Module Fault
6 = Tachometer Fault
7 = Unknown

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 103

Table C.36 Speed Measurement Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
8 Get/Set Locked Rotor REAL The minimum machine CPM
Alert Threshold speed that must be
obtained within the alert
period to avoid an alert
status.
9 Get/Set Locked Rotor REAL The minimum machine CPM
Danger speed that must be
Threshold obtained within the
danger period to avoid a
danger status.
10 Get/Set Locked Rotor USINT The amount of time the Seconds
Alert Period machine has to reach the
alert threshold before an
alert status is indicated.
11 Get/Set Locked Rotor USINT The amount of time the Seconds
Danger Period machine has to reach the
danger threshold before a
danger status is
indicated.
12 Get/Set Time Constant UINT The time constant value Milliseconds
used for exponential
averaging of the Speed
Value (a low pass
filter/output smoothing
filter).
13 Get Acceleration REAL The rate of change of the CPM/min
Speed measurement.

Services

Setting the attributes of this object are not affected by the status of the Device
Mode Object.

Table C.37 Speed Measurement Object Services

Service
Code Class/Instance Usage Name Description
05h Instance Reset Clears Maximum (Peak)
speed to 0.
0Eh Instance Get_Attribute_Single Returns a single attribute.
10h Instance Set_Attribute_Single Sets a single attribute.1

1 Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.

Publication GMSI10-UM004A-EN-E - February 2006

104 DeviceNet Objects

Tachometer Channel Object The Tachometer Channel Object models "front end" processing performed
on a tachometer signal before specific measurements are performed.
(Class ID 326H)

Class Attributes

The Tachometer Channel Object provides no class attributes.

Instances

There are 2 instances of this object.

Instance Attributes

Table C.38 Tachometer Channel Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
3 Get/Set Number of UINT The number of signal 0 = Tachometer disabled
Pulses per pulses per revolution of > 0 = Tachometer enabled
Revolution the shaft (number of gear
teeth).
4 Get/Set Auto Trigger BOOL Indicates whether the 0 = Use specified Trigger Level
trigger level is determined and Hysteresis
automatically from the 1 = Determine trigger level and
signal. hysteresis automatically
5 Get/Set Trigger Level REAL The signal level to be Volts
used as the trigger.
6 Get/Set Trigger Slope USINT The slope of the signal at 0 = Positive
the threshold crossing to 1 = Negative
be used as the trigger.
7 Get/Set Trigger REAL The amount of hysteresis In Auto Trigger mode, this
Hysteresis around the trigger level. value is a percentage of the
peak-to-peak input signal and
can range from 0 to 50%. In
Manual Trigger mode, this
value is a voltage level (the
hysteresis voltage is added or
subtracted to the threshold
voltage to determine the
hysteresis range).

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 105

Table C.38 Tachometer Channel Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
8 Get/Set Name STRING2 A name to help identify 18 character maximum
this channel
9 Get/Set Multiplier REAL A multiplier applied to the > 0
tachometer pulse rate.
10 Get/Set Fault Time-out USINT Number of seconds with 1 to 64 seconds
no pulses before a Tach
Fault is indicated.

Services

Table C.39 Tachometer Channel Object Services

Service
Code Class/Instance Usage Name Description
0Eh Instance Get_Attribute_Single Returns a single attribute.
10h Instance Set_Attribute_Single Sets a single attribute.1

1 Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.

Transducer Object The Transducer Object models a transducer.

(Class ID 328H)
Class Attributes

The Transducer Object provides no class attributes.

Instances

There are 2 instances of this object.

Publication GMSI10-UM004A-EN-E - February 2006

106 DeviceNet Objects

Instance Attributes

Table C.40 Transducer Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
3 Get DC Bias REAL The measured average DC Volts
bias of the transducer
signal in volts.
4 Get Status BOOL Indicates whether a 0 = No fault
transducer fault exists 1 = A transducer fault exists
(the measured DC Bias is
outside the range
specified by Fault High
and Low).
7 Get/Set Fault High REAL The maximum expected Volts
DC Bias voltage from the
transducer in volts.
8 Get/Set Fault Low REAL The minimum expected Volts
DC Bias voltage from the
transducer in volts.
9 Get/Set Power Type USINT Indicates the type of 0 = No power supplied
power supplied to the 3 = Bias current for passive
transducer. magnetic sensors
13 Get/Set DC Bias Time REAL The time constant value Seconds
Constant used for exponential
averaging of the DC Bias
value (a low pass
filter/output smoothing
filter).

Services

Table C.41 Transducer Object Services

Service
Code Class/Instance Usage Name Description
0Eh Instance Get_Attribute_Single Returns a single attribute.
10h Instance Set_Attribute_Single Sets a single attribute.1

1 Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.

Publication GMSI10-UM004A-EN-E - February 2006

 DeviceNet Objects 107

4-20mA Output Object The 4-20mA Output Object models the configuration of a 4-20mA output
signal.
(Class ID 32AH)

Class Attributes

The 4-20mA Output Object provides no class attributes.

Instances

There are 2 instances of this object.

Instance Attributes

Table C.42 4-20mA Output Object Instance Attributes

Access
Attr ID Rule Name Data Type Description Semantics
3 Get Value REAL The current output value. mA
4 Get/Set Enable BOOL Indicates whether this 0 = Disabled
4-20mA output is 1 = Enabled
enabled.
5 Get/Set Max Range REAL The measured value
associated with 20mA.
6 Get/Set Min Range REAL The measured value
associated with 4mA.
7 Get/Set Measurement EPATH Identifies the class, See Parameter Object instances
Identifier Path instance, and attribute of 2 and 3.
a measurement value that
this 4-20mA output is See DeviceNet Specification
tracking. Volume 1 Appendix I.

Publication GMSI10-UM004A-EN-E - February 2006

108 DeviceNet Objects

Services

Table C.43 4-20mA Output Object Services

Service
Code Class/Instance Usage Name Description
0Eh Instance Get_Attribute_Single Returns a single attribute.
10h Instance Set_Attribute_Single Sets a single attribute.1

1 Attributes can only be set while the device is in Program Mode. See the description of the Device Mode Object
for more information.

Publication GMSI10-UM004A-EN-E - February 2006

 Glossary

alarm

An alarm alerts you to a change in a measurement. For example, an alarm can

notify you when the measured vibration level for a machine exceeds a
pre-defined value.

Automatic Device Replacement (ADR)

A means for replacing a malfunctioning device with a new unit, and having the
device configuration data set automatically. The ADR scanner uploads and
stores a device’s configuration. Upon replacing a malfunctioning device with a
new unit (MAC ID 63), the ADR scanner automatically downloads the
configuration data and sets the MAC ID (node address).

baud rate

The baud rate is the speed at which data is transferred on the DeviceNet
network. The available data rates depend on the type of cable and total cable
length used on the network:

Maximum Cable Length

Cable 125K 250K 500K
Thick Trunk Line 500m (1,640ft.) 250m (820ft.) 100m (328ft.)
Thin Trunk Line 100m (328ft.) 100m (328ft.) 100m (328ft.)
Maximum Drop Length 6m (2 ft.) 6m (20ft.) 6m (20ft.)
Cumulative Drop Length 156m (512ft.) 78m (256ft.) 39m (128ft.)

The XM measurement module’s baud rate is automatically set by the bus

master. You must set the XM-440 Master Relay module’s baud rate. You set the
XM-440 to 125kb, 250kb, 500kb, or Autobaud if another device on the
network has set the baud rate.

bus off

A bus off condition occurs when an abnormal rate of errors is detected on the
Control Area Network (CAN) bus in a device. The bus-off device cannot
receive or transmit messages on the network. This condition is often caused by
corruption of the network data signals due to noise or baud rate mismatch.

Change of State (COS)

DeviceNet communications method in which the XM module sends data

based on detection of any changed value within the input data (alarm or relay
status).

109 Publication GMSI10-UM004A-EN-E - February 2006

Glossary 110

current configuration

The current configuration is the most recently loaded set of configuration

parameters in the XM module’s memory. When power is cycled, the current
configuration is loaded with either the saved configuration (in EEPROM) or
the factory defaults (if there is no saved configuration). In addition, the current
configuration contains any configuration changes that have been downloaded
to the module since power is applied.

DeviceNet network

A DeviceNet network uses a producer/consumer Controller Area Network

(CAN) to connect devices (for example, XM modules). A DeviceNet network
can support a maximum of 64 devices. Each device is assigned a unique node
address (MAC ID) and transmit data on the network at the same baud rate.

A cable is used to connect devices on the network. It contains both the signal
and power wires. General information about DeviceNet and the DeviceNet
specification are maintained by the Open DeviceNet Vendor’s Association
(ODVA). ODVA is online at http://www.odva.org.

disarm state

See Program mode.

EEPROM

See NVS (Non-Volatile Storage).

Electronic Data Sheet (EDS) Files

EDS files are simple text files that are used by network configuration tools
such as RSNetWorx for DeviceNet to describe products so that you can easily
commission them on a network. EDS files describe a product device type,
revision, and configurable parameters.

Publication GMSI10-UM004A-EN-E - February 2006

 Glossary 111

Help window

A window that contains help topics that describe the operation of a program.
These topics may include:

• An explanation of a command.
• A description of the controls in a dialog box or property page.
• Instructions for a task.
• Definition of a term.

MAC ID

See node address.

master device

A device which controls one or more slave devices. The XM-440 Master Relay
module is a master device.

node address

A DeviceNet network can have as many as 64 devices connected to it. Each

device on the network must have a unique node address between 0 and 63.
Node address 63 is the default used by uncommissioned devices. Node
address is sometimes called "MAC ID."

NVS (Non-Volatile Storage)

NVS is the permanent memory of an XM module. Modules store parameters

and other information in NVS so that they are not lost when the module loses
power (unless Auto Save is disabled). NVS is sometimes called "EEPROM."

online help

Online help allows you to get help for your program on the computer screen
by pressing F1. The help that appears in the Help window is context sensitive,
which means that the help is related to what you are currently doing in the
program.

Polled

DeviceNet communications method in which module sends data in response

to a poll request from a master device.

Publication GMSI10-UM004A-EN-E - February 2006

Glossary 112

Program mode

The XM module is idle. Typically this occurs when the module configuration
settings are being updated with the XM Configuration program. In Program
mode, the signal processing/measurement process is stopped. The status of
the alarms is set to the disarm state to prevent a false alert or danger status.

Run mode

In Run mode, the module collects measurement data and monitors each
measurement device.

settling time

The amount of time it takes a measurement to reach 90% of the final value
given a step change in the input signal.

slave device

A device that receives and responds to messages from a Master device but
does not initiate communication. Slave devices include the XM measurement
modules, such as the XM-120 Dynamic Measurement module and the XM-220
Dual Speed module.

transducer

A transducer is a device for making measurements. These include

accelerometers, velocity pickups, displacement probes, and temperature
sensors.

virtual relay

A virtual relay is a non-physical relay. It has the same capabilities (monitors

alarms, activation delay, change status) as a physical relay only without any
physical or electrical output. The virtual relay provides additional relay status
inputs to a controller, PLC, or an XM-440 Master Relay module (firmware
revision 5.0 and later).

XM configuration

XM configuration is a collection of user-defined parameters for XM modules.

XM Serial Configuration Utility software

XM Serial Configuration Utility software is a tool for monitoring and

configuring XM modules. It can be run on computers running Windows 2000
service pack 2, Windows NT 4.0 service pack 6, or Windows XP operating
systems.

Publication GMSI10-UM004A-EN-E - February 2006

 Index

Numerics relay parameters 51

24V common grounding requirements 10 tachometer parameters 45
4-20mA Output Object 107 connecting wiring 16
4-20mA output parameters 56 4-20mA outputs 24
Enable 56 buffered outputs 22
Max Range 56 DeviceNet 35
Measurement 56 power supply 18
Min Range 56 relays 19
4-20mA outputs, wiring 24 remote relay reset signal 25
serial port 34
startup switch 27
A switched buffered output 23
Acknowledge Handler Object 95 terminal base XM-941 16
Alarm Object 96 transducers 27
alarm parameters 48 Connection Object 87
Alarm 48 COS message format 75
Alert Period 50
Alert Threshold (High) 50
Alert Threshold (Low) 50
D
Condition 49 data parameters 58
Danger Period 50 Acceleration 58
Danger Threshold (High) 50 Acceleration Alarm Status 59
Danger Threshold (Low) 50 Locked Rotor Alarm Status 60
Enable 49 Peak Speed 58
Hysteresis 50 Relay Status 60
Inhibit Tachometer Fault 51 Reverse Rotation Status 58
Name 49 Speed 58
Startup Period 51 Speed Alarm Status 59
Assembly Object 83 Startup Status 58
Transducer Measure DC Bias 58
Xdcr DC Bias 58
B Zero Speed Alarm Status 59
baud rate 37 description
buffered outputs, wiring 22 configuration parameters 43
XM-220 module 3
C XM-441 module 3
XM-941 terminal base 2
Channel Status indicator 40
Device Mode Object 98
Class Instance Editor 71
Device Mode parameter 61, 69, 70
components
Device Mode parameters 61
XM-220 module 3
Autobaud 61
XM-441 Expansion Relay module 3
Device Mode 61, 69, 70
XM-941 terminal base 2
DeviceNet connection
configuration parameters 43
baud rate 37
4-20mA output parameters 56
node address 36
alarm parameters 48
wiring 35
data parameters 58
DeviceNet grounding requirements 11
device mode parameters 61
DeviceNet information
I/O data parameters 57
EDS files 69
measurement mode parameter 44

Publication GMSI10-UM004A-EN-E - February 2006

114 Index

I/O message formats 73 I/O message formats

invalid device configuration errors 72 change of state (COS) messages 75
setting the Device Mode parameter 69, 70 poll messages 73
XM services 71 XM status values 75
DeviceNet Object 82 Identity Object 80
DeviceNet objects 79 indicators 38
4-20mA Output 107 Channel Status 40
Acknowledge Handler 95 Module Status 39
Alarm 96 Network Status 40
Assembly 83 Relay 41
Connection 87 Startup 40
Device Mode 98 installation requirements
DeviceNet 82 grounding 7
Discrete Input Point 89 power 6
Identity 80 wiring 6
Parameter 90 interconnecting terminal base units 14
Relay 99 introduction 1
Speed Measurement 102 invalid device configuration errors 72
Tachometer Channel 104
Transducer 105
K
DIN Rail Grounding Block 8
DIN rail grounding requirements 7 keyswitch 37
Discrete Input Point Object 89
document conventions 4 M
dual channel mode 1, 44 measurement mode parameter 44
Mode 44
E measurement modes
Electronic Data Sheet (EDS) files 69 dual channel 1, 44
reverse rotation 1, 44
single redundant channel 1, 44
G Module Status (MS) indicator 39
grounding requirements 7 mounting
24V common 10 terminal base unit on DIN rail 12
DeviceNet 11 terminal base unit on panel/walll 15
DIN rail 7 XM-220 module on terminal base 37
panel/wall mount 9
switch input 12
transducers 11
N
Network Status (NS) indicator 40
node address 36
I normally closed relay contacts 19
I/O data parameters 57 normally open relay contacts 19
Assembly Instance Table 57
COS Output 57
O
COS Size 57
Custom Assembly 57 operating mode
Poll Output 57 program mode 39, 69
Poll Response Assembly 57 run mode 39, 69
Poll Size 57, 58

Publication GMSI10-UM004A-EN-E - February 2006

 Index 115

P single redundant channel mode 1, 44

panel/wall mount grounding requirements 9 specifications 63
Parameter Object 90 Speed Measurement Object 102
poll message format 73 Startup indicator 40
Assembly instance 101 74 startup switch, wiring 27
Assembly instance 102 74 switch input grounding requirements 12
Assembly instance 103 74 switched buffered output, wiring 23
power requirements 6
power supply, wiring 18 T
program mode 39, 69 Tachometer Channel Object 104
tachometer parameters 45
R Auto Trigger 47
relay contacts Bias Current 46
normally closed 19 DC Bias Time Constant 47
normally open 19 Fault High 46
Relay indicator 41 Fault Low 46
Relay Object 99 Fault Time-Out 48
relay parameters 51 Name 45
Activation Delay 52 Pulses per Revolution 48
Activation Logic 53 Speed Multiplier 48
Alarm A 53 Tach Multiplier 48
Alarm B 53 Trigger Hysteresis 47
Alarm Identifier A 53 Trigger Mode 47
Alarm Identifier B 53 Trigger Slope 48
Alarm Levels 54 Trigger Threshold 48
Alarm Status to Activate On (Alarm Levels) 54 terminal base
Enable 52 interconnecting units 14
Failsafe 55 mounting on DIN rail 12
Latching 52 mounting on panel/wall 15
Name 52 terminal block assignment 16
Number 52 transducer grounding requirements 11
Relay Installed 54 Transducer Object 105
relays transducer wiring 27
resetting 25, 41 magnetic pickup sensor 29
wiring 19 non-contact sensor 28
remote relay reset signal, wiring 25 TTL output device 31
reset switch 41
reverse rotation mode 1 W
configuring 44 wiring
sensor placement 33 to separate power connections 6
run mode 39, 69 to terminal base 16
wiring connections
S 4-20mA outputs 24
self-test, status 41 buffered outputs 22
sensor placement, reverse rotation 33 DeviceNet 35
serial port connection power supply 18
mini-connector 35 relays 19
terminal base unit 34 remote relay reset signal 25

Publication GMSI10-UM004A-EN-E - February 2006

116 Index

serial port 34 indicators 38

startup switch 27 introduction 1
switched buffered output 23 mounting 37
transducers 27 power requirement 6
wiring requirements 6 reset switch 41
self-test 41
specifications 63
X
wiring requirements 6
XM Services 71 XM-220 I/O message formats 73
XM status values 75 XM-441 Expansion Relay Module 3, 51
XM-220 Dual Speed Module XM-941 terminal base
components 2 description 2
configuration parameters 43 mounting 12
description 3 wiring 16
grounding requirements 7

Publication GMSI10-UM004A-EN-E - February 2006

 Index 117

Publication GMSI10-UM004A-EN-E - February 2006

Rockwell Automation Rockwell Automation provides technical information on the web to assist you in using
our products. At http://support.rockwellautomation.com, you can find technical
Support manuals, a knowledge base of FAQs, technical and application notes, sample code and
links to software service packs, and a MySupport feature that you can customize to
make the best use of these tools.

For an additional level of technical phone support for installation, configuration and
troubleshooting, we offer TechConnect Support programs. For more information,
contact your local distributor or Rockwell Automation representative, or visit
http://support.rockwellautomation.com.

Installation Assistance

If you experience a problem with a hardware module within the first 24 hours of
installation, please review the information that's contained in this manual. You can also
contact a special Customer Support number for initial help in getting your module up
and running:

United States 1.440.646.3223

Monday – Friday, 8am – 5pm EST
Outside United Please contact your local Rockwell Automation representative for any
States technical support issues.

New Product Satisfaction Return

Rockwell tests all of our products to ensure that they are fully operational when
shipped from the manufacturing facility. However, if your product is not functioning
and needs to be returned:

United States Contact your distributor. You must provide a Customer Support case
number (see phone number above to obtain one) to your distributor in
order to complete the return process.
Outside United Please contact your local Rockwell Automation representative for
States return procedure.

Publication GMSI10-UM004A-EN-E - February 2006 119

Supersedes Publication ENMON-UM220A-EN-P - October 2004 Copyright © 2006 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.