Scribd
Upload
129 views

Design and Fabrication of Automatic Drainage Cleaning System

This document describes the design and fabrication of an automatic drainage cleaning system by three students. The system uses a metal frame with teeth attached to a chain that is powered by a motor. As the motor runs, it lifts waste materials like bottles out of the drain and deposits them in a storage tank. The system aims to provide a safer, more efficient way to clean drains compared to manual labor. It is intended to work in drains of various sizes and help prevent blockages caused by debris.

Uploaded by

Yaswanth Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
129 views

Design and Fabrication of Automatic Drainage Cleaning System

This document describes the design and fabrication of an automatic drainage cleaning system by three students. The system uses a metal frame with teeth attached to a chain that is powered by a motor. As the motor runs, it lifts waste materials like bottles out of the drain and deposits them in a storage tank. The system aims to provide a safer, more efficient way to clean drains compared to manual labor. It is intended to work in drains of various sizes and help prevent blockages caused by debris.

Uploaded by

Yaswanth Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

DESIGN AND FABRICATION OF

AUTOMATIC DRAINAGE CLEANING SYSTEM


Submitted by

A.HARISH 510115114015
R.VINOTH KUMAR 510115114047
S.YASWANTH KUMAR 510115114049

BACHELOR OF ENGINEERING
In
MECHANICAL ENGINEERING
At
ADHIPARASAKTHI COLLEGE OF ENGINEERING
G.B.NAGAR KALAVAI.
APRIL 2018

SUPERVISOR PROJECT HEAD HEAD OF DEPARTMENT


SYNOPSIS:
 ABSTRACT
 INTRODUCTION
 WORKING
 MATERIALS REQUIRED
 USES
 CONCLUSION

ABSTRACT:

Drainage Water cleaning and Control System Using auto mechanism


or manual proposed to overcome the real time problems. With the
continued expansion of industries, the problem of sewage water must
be urgently resolved due to the increasing sewage problems from
industries of the surrounding environment. The waste and gases
produced from the industries are very harmful to human beings and to
the environment.

Our proposed system is to cleaning and controls the drainage level


using auto mechanism technique. Auto mechanism is the major
controlling unit and the drainage level is monitor by municipal. In this
system we used motor, chain, driver, bucket, and frame.
INTRODUCTION:

Cleaning of drains/gutters has always been a problem. Labors


cleaning gutters & drain seems unethical and also leads to a high risk
of them catching infections or poisoning due to large amounts of
waste/chemicals in them. Also throwing of bottles/plastics and other
such objects into the gutters lead to narrowing and eventually
blockage in gutter flow. This leads to overflow in many cases. So here
we provide a fully automated drain gutter cleaning mechanism to
tackle these modern day gutter jamming issues.

Our system consists of metal teeth based jaws that wait at the bottom
of the mechanism. It is mounted in a frame to hold the system upright
in the gutter. The vertical frame bed is used to let liquid flow but
catch all solid waste.
WORKING:

 The Device is place across Drain so that only water flow through lower
grids Waste like bottle, etc.
 Floating in drain are lifted by teeth which is connected to chain.
 This chain is attached by sprocket driven by motor or manually.
 When motor Runs The chain starts to circulate making teeth to lift up.
 The waste materials are lifted by teeth and are stored in waste storage
tank.
MATERIALS REQUIRED:

 Frame - mild steel


 Shaft - steel
 Sprocket - steel
 Filter – Iron
 Collector – Sheet Metal
 Object left – Sheet Metal

USES:
 It is used almost in all types if Drainage (Large , Small & medium).
 This machine is mainly used in cleaning system.

 This device is suitable to hold flat type plate. (maximum length1.5 feet).

ADVANTAGES:
 Production cost is very low.
 No need of purchase special machine.
 It is mainly very useful to hold the lengthy plate(1.5 feet) in particular
position.
 Its operated and maintenance is simple.
 It is compact and portable.
 It can be efficiently used.
COST ESTIMATION:

COMPONENTS QUANTITY COST

Aluminum Frame 2x2x3 feet 1500

Chain 2 600

Sprocket 4 500

Wheel 4 200

Battery 1 (12V 7.2 Ah) 600

Hollow shaft 2 300

Welding As Required 200


CONCLUSION:
Thus the project review of the Automatic drainage cleaning Machine
has been explained with its components, uses and its applications.

You might also like