ICs for TV

AN5285K
Sound level automatic gain control IC

■ Overview Unit: mm
10
The AN5285K is a stereo automatic volume control

0.5
1.1
IC for reducing a difference in volume between broad-
casting stations and between programs. It is a kind of

18.24±0.3
AGC circuit and reduces a sudden change in sound sig-
nal amplitude by using a proper time constant.

1.778
■ Features 1
• Sound level AGC function by VCA gain control 6.0±0.3 3.5±0.25

1.65±0.25
• Prevention of S/N ratio degradation by reducing VCA

3.0±0.3
(12.0)
gain at no signal (typ. 20 mV[rms] or less)
• AGC function can be switched on and off externally.
• Operating point of VCA gain lowering is adjustable by

1.1±0.25
0.25 –0.05
means of external resistor.

+0.1
• Usable for stereo sound system (also usable for monau-
ral sound system) by two VCAs SSIP010-P-0000

Note) The package of this product will be changed

■ Applications to lead-free type (SSIP010-P-0000A). See the
• Televisions and video sets new package dimensions section later of this
datasheet.

■ Block Diagram
CC
4 V

3 LOUT
LIN 1 VCA

Level
50 kΩ sensor 1
SW
CTL 7 CTL
Level
sensor 1

RIN 10 VCA
8 ROUT
50 kΩ
Level
sensor 2
V/l reg.
LS2 9

LS1 2

VREF 5

GND 6

Publication date: December 2001 SDB00010BEB 1

AN5285K

■ Absolute Maximum Ratings

Parameter Symbol Rating Unit
Supply voltage VCC 13.0 V
Supply current ICC 30 mA
Power dissipation PD 390 mW
Operating ambient temperature * Topr −20 to +75 °C
Storage temperature * Tstg −55 to +150 °C
Note) * : Except for the operating ambient temperature, and storage temperature, all ratings are for Ta = 25°C.

■ Recommended Operating Range

Parameter Symbol Range Unit
Supply voltage VCC 8.5 to 12.5 V

■ Electrical Characteristics at VCC = 12 V, fIN = 1 kHz, Ta = 25°C

Parameter Symbol Conditions Min Typ Max Unit
Supply current * ICC Without input signal 5 10 15 mA
Input and output level 1 * V1 VIN = 1 mV[rms] 0.7 1.0 1.4 mV[rms]
Input and output level 2 * V2 VIN = 50 mV[rms] 80 110 140 mV[rms]
Input and output level 3 * V3 VIN = 200 mV[rms] 150 200 250 mV[rms]
Input and output level 4 * V4 VIN = 1 V[rms] 200 280 360 mV[rms]
Input and output level 5 V5 VIN = 100 mV[rms], Vctl = 2.5 V 50 100 150 mV[rms]
Input and output level 6 V6 VIN = 300 mV[rms], Vctl = 4.5 V 230 300 370 mV[rms]
Total harmonic distortion * THD VIN = 200 mV[rms]  0.1 0.5 %
Noise level * Vn No input signal (with IHF-A)   100 µV[rms]
Maximum input level * Vmax Input level at THD = 1% 2.8   V[rms]
Crosstalk between channels GT VIN = 2 V[rms], AGC off 60   dB
AGC OFF voltage VSW VIN = 1 V[rms], Vctl = 1.2 V 890 1 000 1 130 mV[rms]
Channel balance * CB VIN = 200 mV[rms] −1.0 0 1.0 dB
Frequency characteristics * FC VIN = 200 mV[rms] −1.0 0 1.0 dB
Level difference of fIN = 1 kHz/20 kHz
Input and output level 7 V7 VIN = 200 mV[rms], AGC off 175 200 225 mV[rms]
Note) * : Vctl = 3.5 V.

2 SDB00010BEB
 AN5285K

■ Terminal Equivalent Circuits

Pin No. Equivalent circuit Description Voltage
1 LIN: 6V
Left side input pin

1 200 Ω

50 kΩ

1/2 VCC

2 LSI: 0.5 V
Level 1 Level 2 CTL
AGC level sensor 1 and 2 to
1.5 V

430 Ω 20 kΩ

3 LOUT: 6V
Left side output pin
143 Ω

143 Ω

4  VCC : 
VCC pin
5 VREF : 6V
Reference voltage stability
50 kΩ

5 200 Ω

50 kΩ

6  GND: 
GND pin

SDB00010BEB 3
AN5285K

■ Terminal Equivalent Circuits (continued)

Pin No. Equivalent circuit Description Voltage
7 CTL: 
AGC on/off changeover
96 kΩ AGC off at 1.2 V or lower
20 kΩ 20 kΩ
200 Ω
7
40 kΩ

8 ROUT: 6V
Right side output pin
143 Ω

143 Ω

9 LS2: 6V
AGC level sensor 2

18 kΩ

900 Ω
250 Ω
1/2 VCC

10 RIN: 6V
Right side input pin

200 Ω

10
50 kΩ

1/2 VCC

4 SDB00010BEB
 AN5285K

■ Application Circuit Example

VCC
4
3 4.7 µF
LOUT
4.7 µF 1
LIN VCA

Level
50 kΩ sensor 1
24 kΩ

SW
CTL 7
CTL
10 kΩ

Level
sensor 1

4.7 µF 10
RIN VCA 4.7 µF
8
ROUT
50 kΩ
Level
sensor 2
V/l Reg.
LS2 9

LS1 2

VREF 5

GND 6
2.2 MΩ

4.7 µF
10 µF

10 µF

■ New Package Dimensions (Unit: mm)

• SSIP010-P-0000A (Lead-free package)

18.24±0.20
6.00±0.20
2.20±0.25
(5.70)

1 10
3.50±0.25

(1.12) 1.778 0.50+0.10

-0.05 0.25+0.10
-0.05
0.90+0.10
-0.05
Seating plane
3.00±0.20
1.65±0.15
1.10±0.15

SDB00010BEB 5
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Govern-
ment if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative character-
istics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or gen-
eral electronic equipment (such as office equipment, communications equipment, measuring in-
struments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchas-
ing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maxi-
mum rating, the range of operating power supply voltage and heat radiation characteristics. Other-
wise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.

Please read the following notes before using the datasheets

A. These materials are intended as a reference to assist customers with the selection of Panasonic
semiconductor products best suited to their applications.
Due to modification or other reasons, any information contained in this material, such as available
product types, technical data, and so on, is subject to change without notice.
Customers are advised to contact our semiconductor sales office and obtain the latest information
before starting precise technical research and/or purchasing activities.
B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but
there is always the possibility that further rectifications will be required in the future. Therefore,
Panasonic will not assume any liability for any damages arising from any errors etc. that may ap-
pear in this material.
C. These materials are solely intended for a customer's individual use.
Therefore, without the prior written approval of Panasonic, any other use such as reproducing,
selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.

2001 MAR