Scribd
Upload
506 views

Simple Inverter Circuit

This document describes a simple inverter circuit using a 13007 transistor in a push-pull configuration with a 12V battery and 220V-12V-220V transformer. The circuit works by alternately turning one transistor on while the other is off, which induces a changing magnetic field in the transformer to output a 220V alternating current from the secondary coil. Following the steps and using the listed components allows one to easily construct this basic inverter to power small loads like an LED bulb from a 12V battery.

Uploaded by

Cris Mendoza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
506 views

Simple Inverter Circuit

This document describes a simple inverter circuit using a 13007 transistor in a push-pull configuration with a 12V battery and 220V-12V-220V transformer. The circuit works by alternately turning one transistor on while the other is off, which induces a changing magnetic field in the transformer to output a 220V alternating current from the secondary coil. Following the steps and using the listed components allows one to easily construct this basic inverter to power small loads like an LED bulb from a 12V battery.

Uploaded by

Cris Mendoza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

instructables

Simple Inverter Circuit

by Creative creator

This is an easy inverter circuit based upon 13007 4. 12V Battery:


Transistor. the essential Inverter works on the Push- https://www.utsource.net/itm/p/8938326.html
Pull con guration. This Inverter is sweet for little
loads like 15w LED Bulbs, mobile charger, and other 5. 15w LED Bulb:
Electrical Accessories. https://www.utsource.net/itm/p/8938326.html

Supplies: Tools Needed:

Needed Components:
1.Soldering Iron:
https://www.utsource.net/itm/p/8423764.html
1. 13007 Transistor:
https://www.utsource.net/itm/p/4011846.html
2. Iron Stand:
https://www.utsource.net/itm/p/7722853.html
2. 330 Ohm Resistor:
https://www.utsource.net/itm/p/8445643.html
3. Nose Pliers:
https://www.utsource.net/itm/p/7671655.html
3. 220v to 12-0-12 Transformer:
https://www.utsource.net/itm/p/8847828.html
4. Flux: https://www.utsource.net/itm/p/8423764.html

Step 1: Watch YouTube Video

Simple Inverter Circuit: Page 1


Here is that the video about Simple Basic Inverter Circuit Diagram from Creative creator. So, watch the

video and you'll get all the points. reaches its saturation state and its T1 Breakdown
stage occurs and therefore the T2 Transistor became
Ho w t he Inv e rt e r Circuit W o rks ? conductive. This whole repeats over and over. This
The Inverter circuit is essentially an Example of the whole process is named Push-Pull Con guration. This
Push-Pull Circuit. Here I even have used 13007 Push-Pull con guration makes Square wave Pulses at
transistors. These transistors are connected like within the rst of the Transformer. This Induces Flux within
the Pic:1. I even have connected a 12-0-12 Transformer the Transformer. coe cient of mutual induction will
with the Tramsictor like within the Pic. occur. Now, the secondary winding is going to be
conducive to the coe cient of mutual induction.
once we give 12V to the circuit then One transistor From this coil, we get the 220V Output.
became conductive at a time. for this reason, one half
the transformer’s coil became conductive. Then it

https://youtu.be/5HSQoRMSf4o

Step 2:

Bend the 13007 Transistor Pins and tin the wires for Better Soldering.

Step 3:

Connect the T1, T2 Transistor’s Emitter together for the 12v inverter circuit.

Simple Inverter Circuit: Page 2


Step 4:

Now connect 330 Ohm resistor as shown within the Figure. One Transistor’s Base is going to be connected with the
Collector of another transistor. And other the other way around.

Step 5:

Connect the T1, T2 Transistor’s Collector with the middle tap Transformer. during this case, The transformer corner
points are going to be utilized. the middle tap i.e. middle pin won't be connected during this 12v to 230v inverter
circuit diagram.

Step 6:

Now Let’s mention Input power. Here i will be able to use a 12V LEAD ACID BATTERY. you'll also use other batteries
Simple Inverter Circuit: Page 3
like Lipo, LI-on also . the middle tap point of the Transformer are going to be used for the +12v supply. The Emitter
pin of the Transistor is for the GND or the -ve.

Step 7:

Now connect the External Load with the Secondary of the Transformer. Here I even have used a 15W LED Bulb as a
Load.

Step 8:

Let’s test it. Here I even have connected a 12v Battery as a DC Input Voltage Source. Here you'll see the LED is
Glowing. So, the circuit works awlessly.

Simple Inverter Circuit: Page 4

You might also like