SBNHH-1D45C

6-port sector antenna, 2x 698–896 and 4x 1695–2360 MHz, 45° HPBW,

3x RET
l Interleaved dipole technology providing for attractive, low wind load mechanical package

l Three internal RETs for independent tilt on all three bands

Electrical Specifications
Frequency Band, MHz 698–806 806–896 1695–1880 1850–1990 1920–2200 2300–2360
Gain, dBi 18.3 18.6 19.6 20.2 20.5 21.0
Beamwidth, Horizontal, degrees 47 43 44 43 42 39
Beamwidth, Vertical, degrees 8.9 8.2 5.8 5.3 5.1 4.5
Beam Tilt, degrees 0– 10 0– 10 0– 8 0– 8 0– 8 0– 8
USLS (First Lobe), dB 17 16 20 20 19 16
Front
Front--to
to--Back Ratio at 180°, dB 30 31 33 35 35 36
CPR at Boresight, dB 25 19 20 24 17 17
CPR at 10 dB Horizontal
11 16 10 10 10 10
Beamwidth, dB
Isolation, Cross Polarization, dB 25 25 25 25 25 25
Isolation, Inter
Inter--band, dB 30 30 30 30 30 30
VSWR | Return Loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -153 -153 -153 -153 -153 -153
Input Power per Port, maximum,
350 350 350 350 350 300
watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*

Frequency Band, MHz 698–806 806–896 1695–1880 1850–1990 1920–2200 2300–2360
Gain by all Beam Tilts, average, dBi 17.9 18.5 19.2 20.0 20.3 20.8
Gain by all Beam Tilts Tolerance,
±0.5 ±0.2 ±0.5 ±0.4 ±0.4 ±0.4
dB
0 ° | 17.8 0 ° | 18.4 0 ° | 19.2 0 ° | 20.0 0 ° | 20.2 0 ° | 20.8
Gain by Beam Tilt, average, dBi 5 ° | 18.0 5 ° | 18.6 4 ° | 19.3 4 ° | 20.0 4 ° | 20.3 4 ° | 20.9
10 ° | 17.9 10 ° | 18.4 8 ° | 19.0 8 ° | 19.8 8 ° | 20.1 8 ° | 20.5
Beamwidth, Horizontal Tolerance,
±1.6 ±2.3 ±1.8 ±0.9 ±1 ±1.6
degrees
Beamwidth, Vertical Tolerance,
±0.5 ±0.3 ±0.3 ±0.2 ±0.3 ±0.1
degrees
USLS, beampeak to 20° above
16 16 16 16 17 16
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
24 25 29 31 32 33
± 30°, dB
CPR at Boresight, dB 25 22 22 26 21 19
CPR at 10 dB Horizontal
14 18 13 11 11 12
Beamwidth, dB

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

page 1 of 4
July 29, 2019

©2019 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: June 11, 2019
SBNHH-1D45C

Array Layout

 
 

General Specifications
Operating Frequency Band 1695 – 2360 MHz   |   698 – 896 MHz
Antenna Type Sector
Band Multiband
Performance Note Outdoor usage
 

Mechanical Specifications
RF Connector Quantity, total 6
RF Connector Quantity, low band 2
RF Connector Quantity, high band 4
RF Connector Interface 7-16 DIN Female
Color Light gray
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Aluminum   |   Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 1460.0 N @ 150 km/h
328.2 lbf @ 150 km/h
Wind Loading, lateral 325.0 N @ 150 km/h
73.1 lbf @ 150 km/h

page 2 of 4
July 29, 2019

©2019 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: June 11, 2019
SBNHH-1D45C

Wind Speed, maximum 241 km/h   |   150 mph

 

Dimensions
Length 2437.0 mm   |   95.9 in
Width 457.0 mm   |   18.0 in
Depth 178.0 mm   |   7.0 in
Net Weight, without mounting kit 36.1 kg   |   79.6 lb
 

Remote Electrical Tilt (RET) Information

Input Voltage 10–30 Vdc
Internal RET High band (2)   |   Low band (1)
Power Consumption, idle state, maximum 2W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Multi-RET)
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   1 male
 

Packed Dimensions
Length 2559.0 mm   |   100.7 in
Width 567.0 mm   |   22.3 in
Depth 311.0 mm   |   12.2 in
Shipping Weight 55.8 kg   |   123.0 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
BSAMNT--M — Middle Downtilt Mounting Kit for Long Antennas for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one
BSAMNT
scissor bracket set.

BSAMNT--3 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
BSAMNT
bracket set and one bottom bracket set.

page 3 of 4
July 29, 2019

©2019 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: June 11, 2019
SBNHH-1D45C

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 4 of 4
July 29, 2019

©2019 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: June 11, 2019