8/9/2019 Manual ADVA FSP 150CC-825

TM

Optical Networking

Fiber Service Platform 150CCf-825

(FSP 150CCf-825)

FSP 150CCf-825 Release 2.1

Quick Start Guide

80000003806 Rev 1.0 December 2008

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 1/30
8/9/2019 Manual ADVA FSP 150CC-825

Copyright © 2001-2008 ADVA AG Optical Networking. All rights reserved.

All rights reserved. Hardware and software mentioned in this document includes software developed by
ADVA AG Optical Networking ("ADVA"), the Apache Software Foundation (http://www.apache.org), Te-
odor Danciu (http://jasperreports.sourceforge.net), and/or other open source software. Some software was
created using ORBacus for Java by Object-Oriented Concepts, Inc.

Trademarks

The terms ADVA, FSP, Etherjack and the Etherjack logo are trademarks or registered trademarks of ADVA
in the United States, Germany and/or other countries. All other company, product, or service mentioned in
this document may be trademarks or service marks of ADVA or their respective owner.

Patents

The content described in this document may be covered by patents or pending patent applications of ADVA.
The furnishing of this document does not give you any license to these patents.

Disclaimers

The content of this document could include technical inaccuracies or typographical errors, and is subject to
change at any time without notice. Reliance on this content is at the relying party's sole risk and will not
create any liability or obligation for ADVA. Any references in this document to non-ADVA publications
and/or non-ADVA Internet sites are provided for convenience only and do not in any manner serve as an
endorsement of those publications and/or Internet sites. The materials within those publications and/or In-
ternet sites are not part of the materials for any ADVA information, product or service, and use of those
 publications and/or Internet sites is at your own risk.

THE CONTENT OF THIS DOCUMENT IS PROVIDED ''AS IS'' AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL ADVA, ITS AFFILIATES, EMPLOYEES, OFFICERS OR ITS SUPPLIERS BE LIA-
BLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUEN-
TIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS DOCUMENT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE. THE SAME APPLIES FOR ANY HARDWARE OR SOFTWARE COVERED BY THIS
DOCUMENT, UNLESS A SIGNED AGREEMENT WITH ADVA OR THE APPLICABLE PRODUCT
LIABILITY LAW EXPRESSLY STATES OTHERWISE.

ADVA AG Optical Networking  Phone+49(0)89-890665-848 

Headquarters  Fax +49(0)89-890665-22848 
Campus Martinsried  www.advaoptical.com
Fraunhoferstr. 9 A 
82152 Martinsried/Muenchen 
Germany

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 2/30
8/9/2019 Manual ADVA FSP 150CC-825

TM

Optical Networking

  FSP 150CCf-825 Quick Start Guide

1.1 Introduction
This document provides step by step procedures to help you locally provision the FSP
150CCf-825 Network Interface Device (NID) to a simple back-to-back configuration. When the
procedures in this document have been completed, the FSP 150CCs will be provisioned from
its default configuration to the following configuration (see Figure 1):

• back-to-back FSP 150CCs on a desk-top (no wall or rack mounting)

• FSP 150CC IP address provisioned

• Minimum required system and WAN interface provisioning

• New users, including new super user 

• VLAN-based WAN management tunnel with PPP layer 2 protocol, DHCP disabled and
RIP V2 packets enabled

• Management LAN port disabled at the SNE (Subtending Network Element)

• LAN port(s) configured in Transparent EVC (Ethernet Virtual Circuit) mode

• SNMP provisioned to enable remote alarm monitoring

Figure 1 Simple Back-to-Back Configuration Supported in This Document

GNE #1 
FSP 150CC WAN SNE #2 
FSP 150CC
LAN(s) PSU1 PSU2  Management  2 4 Access Network    FSP150 CCf  PSU1 PSU2  Management  2 4 Access Network    FSP150 CCf 
LAN(s)
Status Status   Critical  RS-  4 Status Status   Critical  RS-  4
Major  232  Lk Rate Lk Rate   Lk Rate 232  Lk Rate Lk Rate   Lk Rate
3 Major  3
Etherjack  TM Minor   Active  Active
100-  2  Etherjack  TM Minor  2 
LAN  2  100-  LAN  2 
240VAC  Status 1 240VAC  Status 1
1 1
1 3 5 1 1 3 5 1
2  2 

RIP Enabled
Management Tunnel

GNE = Gateway Network Element

SNE = Subtending Network Element

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 1

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 3/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

 All other features will utilize the system default configuration. If your desired configuration
varies from this basic configuration, then provisioning is required. If this is the case, refer to the
FSP 150CCf-825 Installation and Operations Manual for provisioning data and procedures.
For CLI provisioning and CLI command structure information, refer to the FSP 150CCf-825
Etherjack OS (EOS) Command Line Interface Handbook.

Firmware Release Levels Supported in This Release

This version of the FSP 150CCf-825 Quick Start Guide is applicable to the FSP 150CCf-825
software release 2.1. This version of FSP 150CCf-825 is compatible with the nVision Network
Management System software release 9.0 or greater.

Audience

The reader must have sufficient knowledge of the following when using this document:
• IP addressing

• WAN facility provisioning requirements

• LAN EVC provisioning requirements

• fiber handling and cleaning procedures (if connecting fiber cables)

• power handling and connection procedures (if connecting DC power)

Obtaining Technical Assistance

Product Maintenance Agreements and other customer assistance agreements are available
for ADVA Optical Networking AG products through your ADVA Optical Networking distribution
channel. Technical support is available to warranty or maintenance contract customers who
need technical assistance with an ADVA Optical Networking product that is under warranty or
covered by a maintenance contract.
To display ADVA Optical Networking’s Technical Support web site that includes all contact
information, go to ADVA Optical Networking’s home page at http://www.advaoptical.com
and select the “Support” button.

 ADVA Optical Networking’s service options include:

• 24 X 7 telephone support

• Web-based support tools

• On-site support

• Technical training, both on-site and at ADVA facilities in Germany and the USA

• Expedited repair service

• Extended hardware warranty service

Page 2 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 4/30
8/9/2019 TM
Manual ADVA FSP 150CC-825 FSP 150CCf-825 Quick Start Guide
Release 2.1 December 2008
Optical Networking

1.2 Physical Installation

The FSP 150CC installation requires that you establish WAN facility connections between your
local and remote sites, or between your local site and the telco. After your end-to-end
connection has been installed, you are ready to install the FSP 150CCf-825.
The FSP 150CCf-825 is designed for deployment in both customer premises and CO
locations. Wall mount and rack mount brackets, as well as power options, may be ordered
separately. Refer to the FSP 150CCf-825 Installation and Operations Manual for power and
mounting ordering options.

1.2.1 Power Options and Wiring

The following provides power supply requirements as well as instructions for installing the
power and cabling for the FSP 150CCf-825. Refer to the FSP 150CCf-825 Installation and
Operations Manual and the following information for determining PSU and/or power adapter
cabling requirements for your site.

Power Requirements
The system is powered by dual AC and/or DC Power Supply Units (PSUs). PSUs can be of
similar type or mixed, and are hot swapable. It can be equipped with two AC modules, two DC
modules, or one of each. They are physically accessed at the front of the unit and source
connections are located on the front of each PSU module.
Optionally, a third possible power source, an external AC to 12 VDC power converter, may be
used. The 12 VDC power converter may be used alone, or mixed with AC and/or DC power
supply modules. It is physically connected at the rear of the unit. AC power converters may be
ordered separately for North American and international location.
If an external AC power converter and/or one PSU module fails - or its input source fails, the
remaining module continues to power the system without interruption to system function.

Note: The power supplies are not designed to operate in load-sharing mode.

AC Supply
The system operates with an AC source fused at 15A, with the voltage range specified in ANSI
specification C84.1-1989, Voltage Ratings (60 Hz) for Electric Power Systems Equipment, 
Range B. The FSP 150CCf-825 can tolerate any frequency within the range of 60 (+/-3) Hz for
North American applications, and the range of 50 (+/-3) Hz for European applications. The
maximum power consumption from the 230 VAC supply is 40W.

DC Supply
The DC power connector is a 3-pin socket (Battery, Return, Frame Ground) which includes a
mated connector, providing protection against improper (reversed polarity) connection at the
NID. The maximum power consumption from the -48 VDC supply is 40W. External fuse rating

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 3

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 5/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

is 5A.
The FSP 150CCf-825 operates properly when supplied with minimum and maximum operating
voltages for North American and International applications, as shown in Table 1-1.

Table 1-1 Minimum and Maximum Operating Voltages

Nominal Voltage Minimum Maximum Minimum Maximum
Operating Voltage Operating Voltage Abnormal Voltage Abnormal Voltage

-48 -40.5 -57.0 0 -60.0

-60 -50 -72 0 -75

External AC to 12 VDC Power Converter 

The system also provides an optional AC to 12 VDC converter input on the rear panel,
externally fused at 15A. North American and International versions are available (see the FSP
150CCf-825 Installation and Operations Manual for converter options and part numbers).

Connect Cables and Apply Power 

For all FSP 150CCf-825 installations, you will need the proper PSU, power cables and/or
power adapter for your site, and cabling related tools and supplies, as required by local
practices. For DC powered FSP 150CCf-825 power supply units, you will need the following
items for this procedure:

• Screwdriver 
• Wire wrap tool

• Wire cutters

• Wire strippers

• Volt meter

• Fuse panel

• Other power related tools and supplies as required by local practices

For optical cabling installation, you will need the following items for this procedure:
• Optical Power Meter 

• Fiber Cleaner

• Small Form-factor Plug-ables (SFPs), as required

If required, refer to the FSP 150CCf-825 Installation and Operations Manual for connector

and LED descriptions when performing the following procedure.

Page 4 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 6/30
8/9/2019 TM
Manual ADVA FSP 150CC-825 FSP 150CCf-825 Quick Start Guide
Release 2.1 December 2008
Optical Networking

Procedure

Mount the FSP 150CC to a Wall or Rack, as required 

Step 1 For desktop or communications closet installations, go to the next step. Otherwise,
mount the FSP 150CCs, as required. Mounting adapters are provided for mounting
to a wall, 19” rack or 23” rack. Refer to FSP 150CCf-825 Installation and
Operations Manual for detailed procedures.

If additional FSP 150CCs are to be stacked above each other, are installed above heat
producing components, or are installed below heat sensitive components, some FSP
150CC variants require that heat deflector(s) are installed. Install air deflector(s) as
described in Table 2.

Table 2 Air Flow Requirements for the FSP 150CCf-825

Air Flow Requirements

Multiple units may be stacked up to 5 rows high in an environmentally controlled

environment, such as a Central Office. A heat deflector should be installed between
every 5 rows of FSP 150CC NIDs. If it is necessary to install 5 rows of NIDs above other
heat producing components, it is recommended that a heat deflector is installed below
the NIDs. If it is necessary to install heat sensitive equipment above 5 rows of NIDs, it
is recommended that a heat deflector is installed above the NIDs.

Insert SFPs, Run and Connect Power Cables

Step 2 Connect the ground cable, as required.

Step 3 If using optical WAN/LAN interfaces: Obtain the proper SFP (Small Form-factor
Plug-able), and insert it/them into the optical port(s).

Step 4 Determine the next step.

Current Status Then

Does/will the FSP 150CCf-825 include a DC power Continue with the next step.
supply unit?
Does/will the FSP 150CCf-825 NOT include a DC Go to Step 17.
power supply unit?

DANGER —  Avoid the risk of electrical shock. Follow local procedures for working with
electrical power. High voltage may be present in the following tasks. Shut off the power
from the power source or turn off the circuit breakers before proceeding. Use properly
insulated tools when working with power connections. Do not allow any metal objects
to connect across power terminals.

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 5

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 7/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

Step 5 Verify that the office DC power supply is set up to deliver the correct operating voltage
to the FSP 150CCf-825 (between -40.5 and -72 VDC). Verify that the correct fuse or
breaker (5 A rating) is installed at the power supply source and that power is turned
off. Repeat for a second DC power supply source, if present.
Step 6 Using a volt meter, measure the voltages at the source power supply terminals. Verify
that no voltage is present. Repeat for a second DC power supply source, if present.
Step 7 Run the DC power cables (shipped with the power supply unit) from the FSP
150CCf-825 to the office battery terminals. Dress the power cables. Repeat for a
second DC power supply unit, if present.

Step 8 Remove the blank PSU front panel, then insert the DC power supply unit into the front
panel. Repeat for a second DC power supply unit, if present. If the second PSU slot
is unused, ensure that a blank PSU card is inserted into the slot. Tighten the thumb
screws on both PSU slots.

Step 9 Connect the green Frame Ground wires to the Frame Ground terminal. Repeat for
a second DC power supply unit, if present.

Step 10 Connect the black Office Return wires to the RTN DC power supply terminals.
Repeat for a second DC power supply unit, if present.

Step 11 Connect the red Office Battery wires to the BATT DC power supply terminals. Repeat
for a second DC power supply unit, if present.

Step 12 Verify that all power terminal connections are tight and that no strands of wire are
shorting terminals together. Repeat for a second DC power supply unit, if present.

Step 13 Reconnect the office power source (reinstall fuses, reset breakers or turn on supply).
Repeat for a second DC power supply unit, if present.
Step 14 Use a volt meter to verify the A side power and ground at the power terminals. Ensure
that the voltage between BATT and RTN terminals measures between -40.5 and -72
VDC. Repeat for a second DC power supply unit, if present.

Step 15 Using a volt meter, measure the voltage between RTN and Frame GND terminals.
Verify that 2 VDC or less is present. Repeat for a second DC power supply unit, if
present.

Step 16 Connect the power cables to FSP 150CCf-825 front connectors (red wire / connector
release tab oriented at the bottom). Repeat for a second DC power supply unit, if
present. 
The power supply Status LED should illuminate green. During the power cycle, the
front panel Status LED will illuminate red for approximately 1 minute, then will change
to solid green.

Page 6 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 8/30
8/9/2019 TM
Manual ADVA FSP 150CC-825 FSP 150CCf-825 Quick Start Guide
Release 2.1 December 2008
Optical Networking

Step 17 Determine the next step.

Current Status Then

Does/will the FSP 150CCf-825 include an AC power Continue with the next step.
supply unit at the front panel?
Does/will the FSP 150CCf-825 NOT include an AC Go to Step 22.
power supply unit at the front panel, but a 12 VDC
rear connector power adapter will be used?
Only DC power will be used in this installation? Go to Step 23.

Step 18 Run the AC power cable (shipped with the FSP 150CCf-825 power supply unit) from
the FSP 150CCf-825 to the AC power outlet, externally fused at 15A. Dress the power

cables. Repeat for a second AC power supply unit, if present.

Step 19 Remove the blank PSU front panel, then insert the AC power supply unit into the front
panel. Repeat for a second AC power supply unit, if present. If the second PSU slot
is unused, ensure that a blank PSU card is inserted into the slot. Tighten the thumb
screws on both PSU slots.

Step 20 Insert the power cable into the PSU front connector. Then insert the power cable into
the AC power outlet. Repeat for a second AC power supply unit, if present.  
The power supply Status LED should illuminate green. If AC power is the only power
source: During the power cycle, the front panel Status LED will illuminate red for
approximately 1 minute, then will change to solid green.

Step 21 Determine the next step.

Current Status Then

Will a rear accessible 12 VDC power adapter be Continue with the next step.
used?
No rear accessible 12 VDC power adapter will be Go to Step 23.
used?

Step 22 Connect the power adaptor cable to the power connector ( PWR) located at the rear
panel, connect the power cord into the power adapter, then plug the AC adaptor to
an AC (120V or 240V) wall outlet, externally fused at 15A.
If this is the only power source: During the power cycle, the front panel Status LED will
illuminate red for approximately 1 minute, then will change to solid green.

Step 23 Tie-off and secure all power cabling.

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 7

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 9/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

Run and Connect Metallic Cables

Step 24 Run the MGMT LAN port cable and metallic LAN port cables to the FSP 150CCf-825,
as required. Temporarily secure the cables.

Step 25 Connect a LAN Cable to the MGMT LAN port and connect the other end of the cable
to your networking gear (PC, hub, switch, or router). From the factory, the default IP
address of the FSP 150CCf-825 is: 192.168.0.2/24.

Step 26 Determine the next step.

Current Status Then

 Are you only installing fiber optic WAN and LAN Go to Step 36.
cables, and no metallic cables are to be installed?
 Are metallic WAN or LAN cable terminations Continue with the next step.

required for this FSP 150CCf-825?

Step 27 For metallic WAN interface(s): Connect the WAN cable(s) to the designated WAN 
port(s) using a Cat 5 LAN cable (RJ-45 connector). Otherwise, go to the next step.

Step 28 For metallic LAN interface(s): Connect the client Ethernet communications

equipment (PC, hub, switch, or router) to the first designated client LAN port using a
Cat 5 LAN cable (RJ-45 connector). Repeat for each additional client LAN port, as
required. Otherwise, go to the next step.

Step 29 Tie-off and secure all metallic cabling.

Step 30 Determine the next step.

Current Status Then

 Are only metallic cable terminations required for this Go to Step 36.
FSP 150CCf-825 and cabling is complete?
 Are you installing any fiber optic cables? Continue with the next step.

Run and Connect Fiber Optic Cables

The following precautions should be applied when handling fiber optic cables:

DANGER — Follow local safety procedures regarding fiber optic cables.

Never look at the end of a fiber optic cable. Permanent eye damage or blindness can
occur. All optical connectors are shipped with protective caps. Ensure that protective
caps are firmly in place before running any fiber optic cables.

Page 8 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 10/30
8/9/2019 TM
Manual ADVA FSP 150CC-825 FSP 150CCf-825 Quick Start Guide
Release 2.1 December 2008
Optical Networking

DANGER — body. A fiber

touch it to your Never handlecould
fragment exposed
enterfiber opticand
the skin cables withdifficult
be very bare hands or
to detect
and remove.

CAUTION — Optical power performance is affected by dust. Clean all connectors

before performing measurements. Keep the ends of the fiber optic cables covered
when the cables are not in use. The need for cleaning can be minimized if covers are
always used when fibers are not used. Refer to local practices for fiber handling and
cleaning procedures. Clean all connectors before performing measurements.

WARNING — Prevent damage to fiber optic cables. Do not bend fiber optic cables to
a radius less than 50 mm.

WARNING — To avoid damage to optical receivers, do not connect any fibers until
instructed to do so. Always check optical levels before connecting fiber optic cables.

Step 31 Run the optical fiber cables to the FSP 150CCf-825. Do not connect the cable(s) to
the FSP 150CCf-825 connectors at this time. They will be connected later.

Step 32 Dress all fiber optic cables. Use local practices for protecting all cables and
connectors.

Step 33 Test the optical cables according to local practices.

Step 34 Measure the transmit and receive levels of the fiber optic cables and record them for
future reference.

Step 35 Connect the optical interface cables to the appropriate WAN and/or LAN SFP
connectors on the front panel.

Verify WAN and LAN LED Indicators

Step 36 Observe the client LAN LED(s) and refer to FSP 150CCf-825 Installation and
Operations Manual for LED descriptions. If the LAN LED(s) indicate anything other
than the appropriate response for the current state, troubleshoot as necessary.
Step 37 Observe the WAN (Network) LED and refer to FSP 150CCf-825 Installation and
Operations Manual for LED descriptions. If the WAN LED(s) indicate anything other
than the appropriate response for the current state, troubleshoot as necessary.

End of Procedure

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 9

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 11/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

1.3 Provision the FSP 150CC

Perform the following procedure to provision the FSP 150CC. The following procedure will be
performed using the RS-232 serial console using CLI commands and ADVA Optical
Networking’s eVision Web Browser Management Tool. Refer to Figure 2 for an example of the
configuration supported by the following procedure.

You will need the following items for this procedure:

• DB-9 to RJ-45 converter (included in the FSP 150CC kit)

• Category 5 LAN cable (with RJ-45 connectors) for Serial Port RS-232 connection
(included in the FSP 150CC kit)

•  A communications program, like TeraTerm Pro Web (a free software terminal

emulator for MS-Windows) or HyperTerminal (a standard Windows communications
utility)

• Internet Explorer 5.0 or greater 

Figure 2 Back-to-Back Configuration Supported in the Following Procedure

GNE SNE
FSP 150CC #1 FSP 150CC #2
PSU1
Status
PSU2 
Status  
Major 
Management 
Critical  RS- 
232 
2 4

4
3
Access

Lk Rate Lk Rate
Network 

 
 

Lk Rate
FSP150 CCf 
WAN PSU1
Status
PSU2 
Status  
Management 
Critical 
Major 
RS- 
232 
2 4

4
3
Access

Lk Rate Lk Rate
Network 

 
 

Lk Rate
FSP150CCf 

Etherjack  TM Minor   Active  Active

100-  2  Etherjack  TM Minor  2 
LAN  2  100-  LAN  2 
240VAC  Status 1 1
1 240VAC  Status 1
1 3 5 1 1 3 5 1
2  2 

Management Tunnel
System VLAN Based, VLAN ID = 100  System
Proxy ARP = Enabled Layer 2 Protocol = PPP  Proxy ARP = Disabled
Default Router = 192.168.2.1 DHCP = disabled  Default Router = None
RIP V2 Packets = enabled
MGMT LAN Port MGMT LAN Port
IP Address = 192.168.2.2 IP Address = 192.168.2.3
Subnet Mask = 255.255.255.0  Subnet Mask = 255.255.255.0

Static Route
Interface = WAN
IP Address = 0.0.0.0 
Subnet Mask = 0.0.0.0

eVision Workstation
IP Address = 192.168.2.5
Subnet Mask = 255.255.255.0 GNE = Gateway Network Element
Default Gateway = 192.168.2.1 SNE = Subtending Network Element

Page 10 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 12/30
8/9/2019 Manual ADVA FSP 150CC-825

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 13/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

--> show mgmttnl e1000-wan-1

Management Tunnel: e1000-wan-1

  Tunnel Mode: None

  Encapsulation: Ethernet

  Tunnel VLAN ID: 4095

  Tunnel S-Tag: Disabled

  Tunnel S-Tag VLAN ID: 4095

  IP Address: 0.0.0.0

  Subnet Mask: 255.255.255.0

  MAC Address: 00:0B:90:00:47:81

  DHCP: Enabled

  RIPv2: Disabled

  ACL Inbound Filtering: Disabled

Step 5 Observe the DHCP setting to determine the next step.

Current Status Then

Is the WAN port DHCP status set to the desired Go to Step 9.

state of Disabled?
Does the WAN port DHCP setting need to be Continue with the next step.
changed?

Step 6 Use the configure mgmttnl e1000-wan-1 command followed by a carriage return.

 A next level prompt will appear. Then enter dhcp disable followed by a carriage
return. For example:

--> configure mgmttnl e1000-wan-1

config:mgmttnl(e1000)--> dhcp disable

config:mgmttnl(e1000)-->

Step 7 Enter show this followed by a carriage return to verify the changes.

Step 8 Enter exit to go back one level.

Step 9 Enter the IP address and subnet mask, by entering configure system followed by a
carriage return. A next level prompt will appear. Then enter ip-address <address>
<subnet mask>.

--> configure system 

config:sys --> ip-address 192.168.2.3 255.255.255.0

config:sys -->

Page 12 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 14/30
8/9/2019 TM
Manual ADVA FSP 150CC-825 FSP 150CCf-825 Quick Start Guide
Release 2.1 December 2008
Optical Networking

Step 10 Verify the changes by entering show ip followed by a carriage return. The
Management LAN port IP information displays:

config:sys --> show ip

System IP Information:

IP Address: 192.168.2.3

Subnet Mask: 255.255.255.0

Default Gateway:

WARNING — Do not remove power while performing the next step. Removing power
while the operation in progress may corrupt the database.

Step 11 Enter database save followed by a carriage return. The system will display a warning
message and when complete, the CLI prompt will appear, as shown below:

config:sys --> database save

Saving configuration. Do not power down the system.

config:sys -->

Step 12 Enter logout followed by a carriage return.

The login prompt will appear 
Step 13 Remove commissioning cables from the RS-232 port and the PC.

Establish Communications via eVision

Verify the local Management LAN port communication settings by accessing the FSP 150CC’s
eVision Web Browser Management Tool. Perform the following steps:

Step 14 Change your PC IP address to successfully access the FSP 150CC’s Management
LAN port IP address.

Step 15 Use an Ethernet Category 5 LAN cable to connect your PC to the FSP 150CC
Management LAN port. Refer to the FSP 150CCf-825 Installation and Operations
Manual for the Management LAN port connector location, if required.

Step 16  Activate an Internet Explorer web browser on your PC by double clicking on the
shortcut icon.

Step 17 Enter the FSP 150CC’s Management LAN port IP address in the web browser
address field and enter return. 
 A security alert window will appear 

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 13

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 15/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

Step 18 Verify that the security certificate is valid. Select Yes to proceed. 

The FSP 150CC login window appears

Step 19 Enter the default User ID root and Password ChgMeNOW.

Page 14 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 16/30
8/9/2019 TM
Manual ADVA FSP 150CC-825 FSP 150CCf-825 Quick Start Guide
Release 2.1 December 2008
Optical Networking

Step 20 Select Login. 

The default security banner displays as shown in the following example

Note: If a login error appears, re-enter the user ID and password. Up to 3 login attempts
will be processed. On a failed third attempt, the web browser will redirect to a 401
error page (Unauthorized error). If this occurs, the login process must be
re-started by going back to the web browser home page and re-entering the FSP
150CC IP address (at Step 17).

Step 21 Select Continue. 

The eVision Web Browser Management Tool will display, as shown in the
following example (see the following eVision Web Browser Management Tool
components)

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 15

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 17/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

Title Bar  Tool Bar  Login Name

Menu Bar 

System
Name

Menu Tree

View Tabs

Entity
View Area

Status Bar   Alarms Window Secure Session Indicator 

Provision the WAN Interface

Step 22 Expand nested items in the System Name entity by selecting the “+” next to the
System Name entity in the menu tree (default is FSP150CCf-825).

Step 23 Enter a right mouse click on the WAN entity. 

 A drop down menu displays

Page 16 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 18/30
8/9/2019 TM
Manual ADVA FSP 150CC-825 FSP 150CCf-825 Quick Start Guide
Release 2.1 December 2008
Optical Networking

Step 24 Select Edit Facility. 

The Edit Facility view displays

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 17

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 19/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

Step 25 Use the following WAN interface options (as applicable) to provision the WAN
interface with the minimal WAN interface provisioning options required prior to setting
up WAN port communications (see Chapter 5 of the FSP 150CCf-825 Installation
and Operations Manual for WAN interface configuration options and rules):
Table 1-2 Minimum WAN Interface Provisioning via CLI Commands
Command Description
WAN Port
adminstate Defines the WAN facility administrative state.
 media Defines the WAN interface media type.
 
speed  Defines the line rate of the Ethernet port and whether it is in half duplex or full duplex mode.

Step 26 Select OK. 

The WAN Facility view displays the changes made

Step 27 Verify WAN changes made.

Edit WAN Management Tunnel 

Step 28 Right-click on MGMT Tunnel [WAN] and select Edit Mgmt Tunnel.
The Management Tunnel view displays

Page 18 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 20/30
8/9/2019 Manual ADVA FSP 150CC-825

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 21/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

Step 43 Select OK. 

The new User information is displayed in the Users view

Step 44 Expand the Users tree. 

The new user is listed 

Step 45 Select the new User name and view the new user information to verify new user entry.
(The new user password is not displayed for security reasons.)

Step 46  Activate a new Internet Explorer web browser window on your PC by double clicking
on the shortcut icon.

Step 47 Enter the FSP 150CC’s Management LAN port IP address in the web browser
address field and enter return. 
The Login Screen will appear 

Step 48 Enter the new Super User’s user name and password and select OK. 
The eVision Web Browser Management Tool displays
Step 49 Expand the System Name, Administration and Users entities by selecting the “+” next
to each entity.

Step 50 Enter a right click on the root user and select Delete User . Then select OK. 
The default root user is removed from the menu tree

Step 51 If desired, enter other users by repeating Step 41 through Step 45.

Provision SNMP, if Required 

Step 52 If SNMP provisioning is not required, go to Step 59. Otherwise continue with the next
step to provision SNMP.
Step 53 Right click on the SNMP entity in the menu tree and select Add Community. 
The add community screen appears

Step 54 Enter the desired Community Name, select the desired Access Type and then
select Add. 
The new community information is displayed 

Step 55 Right click on the SNMP entity in the menu tree and select Add Target Address. 
The add target address screen appears

Step 56 Select the desired Security Model and Credentials. Enter the desired IP Address and
port. Then select Add.
Step 57 Select the Target Addresses tab to verify the entry.

Step 58 Repeat Step 53 through Step 57 as required.

Page 20 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 22/30
8/9/2019 TM
Manual ADVA FSP 150CC-825 FSP 150CCf-825 Quick Start Guide
Release 2.1 December 2008
Optical Networking

Create Static Route (SNE only)

Step 59 Right click on the Communications entity in the menu tree and select Create Static

Route . 
The create static route screen appears

Step 60 For Route Type, select Interface, and for Interface, select Wan.
Step 61 For IP Address, enter 0.0.0.0.

Step 62 For IP Mask , enter 0.0.0.0.

Step 63 Select OK. 

The Static Route entry displays in the Static Routes tab

Provision LAN(s)

Step 64 Provision the LAN(s) by performing the procedure in Provision LAN(s) in

Transparent EVC Mode, on Page 25.

Disable Local Management Port (SNE only)

Step 65 Right click on the Local Management Port  and select Edit Facility. 
The edit Local Management Port screen appears

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 21

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 23/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

Step 66 Set the Administration State to Disabled.

Step 67 Select OK (communications will be dropped and the configuration will need to be
saved using CLI, as described in the following steps).

Note: The browser will appear to stay busy after OK is selected because it is
attempting to reach the IP address of the FSP 150CC who’s Local
Management Port has just been disabled.

Step 68 Install the console cable between the FSP 150CC RS-232 Port and a PC using the
RJ-45 cable and the DB-9 converter.

Step 69 From the PC, start a communications utility application, such as HyperTerminal with
the following COM port settings:

Note: The Serial Console Port supports only 9600 baud. Do not use Autobaud.

COMM Port COMM Port

Parameter  Setting

Rate 9600 baud

Data Bits 8
Stop Bits 1
Parity No
Flow Control None

Step 70 Hit the “Enter” key and you will be prompted to enter a login and password. The
default login and password are ‘ root’ and ‘ChgMeNOW,’ respectively. A warning
banner displays and the user is prompted to reply [Y|N]. Enter “y” and the serial
console CLI prompt (-->) is displayed.

Step 71 Enter show interface mgmt-lan followed by a carriage return. The DHCP setting will
display, as shown below. Verify that the Administration State is set to Disabled.

--> show interface mgmt-lan

Management Interface: mgmt-lan 

Administrative State: Disabled

Operational State: Disabled

MAC Address: 00:0B:90:00:08:31

MTU: 1500

Interface Speed: Auto

Negotiated Speed: 100 Mb Full Duplex

DHCP: Disabled

RIPv2: Disabled

Page 22 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 24/30
8/9/2019 TM
Manual ADVA FSP 150CC-825 FSP 150CCf-825 Quick Start Guide
Release 2.1 December 2008
Optical Networking

WARNING — Do not remove power while performing the next step. Removing power
while the operation in progress may corrupt the database.

Step 72 Enter database save followed by a carriage return. The system will display a warning
message and when complete, the CLI prompt will appear, as shown below:

--> database save

Saving configuration. Do not power down the system.

-->

Step 73 Enter logout followed by a carriage return.

The login prompt will appear 

Step 74 Remove any commissioning cables (Ethernet cable and/or console cable) from the
FSP 150CC front panel connectors, as required.

Step 75 Verify that the WAN cable is connected to the FSP 150CC WAN port.

Perform the following at FSP 150CC #1 (GNE):

Provision the FSP 150CC’s IP Address, WAN Interface, WAN Management Tunnel, New
Super User and SNMP 

Step 76 Perform Step 1 through Step 58.

Provision LAN(s)

Step 77 Provision the LAN(s) by performing the procedure in Provision LAN(s) in

Transparent EVC Mode, on Page 25.

Enable Proxy ARP at the GNE 

CAUTION — Do not enable Proxy ARP if both units are connected to the same LAN
via the Management LAN port. Otherwise, there will be multiple ARP responses for a
single ARP request for a remote reachable IP address from each NE/FSP 150CC in
the same LAN that has Proxy ARP enabled.

Step 78 Right-click on the System Name and select Edit Settings. 

The edit system settings screen appears

Step 79 Set Proxy ARP to Enabled.

Step 80 Select OK.

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 23

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 25/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

Step 81 Save the configuration in eVision by selecting File and then Save Changes from the
menu bar.

Verify Connectivity to the SNE 

Step 82 Verify that the WAN cable is connected to the FSP 150CC WAN port.

Step 83 Observe the WAN LED (and in the case of SONET/SDH 1+1 protection, the WAN 2
LED) on the front panel of each FSP 150CC. If the WAN LED(s) indicate anything
other than the appropriate response for the current state, troubleshoot the WAN
connections between FSP 150CC #1 and FSP 150CC #2 as necessary (refer to the
FSP 150CC Installation and Operations Manual for LED descriptions for each FSP
150CC variant).

Step 84 Flush ARP cache on the PC by opening a DOS window (select Start and then Run),
entering ARP -d and then selecting OK.

Step 85 Verify connectivity to FSP 150CC #2. Open an Internet Explorer web browser window
and enter the IP address of FSP 150CC #2. Logon using a valid user name and
password.

Step 86 Remove any commissioning cables (Ethernet cable and/or console cable) from the
FSP 150CC front panel connectors, as required.

End of Procedure

Page 24 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 26/30
8/9/2019 TM
Manual ADVA FSP 150CC-825 FSP 150CCf-825 Quick Start Guide
Release 2.1 December 2008
Optical Networking

Provision LAN(s) in Transparent EVC Mode

This procedure can be used for provisioning one or more LAN in Transparent EVC mode using

the
andeVision
ensure web browser.
that they meetItthe
is recommended
FSP 150CC’s that you pre-determine
provisioning rules prior the provisioning
to making details
changes to a
LAN or placing an additional LAN into service. Ensure that CIR, EIR and C-Tag/S-Tag VLAN
ID-Priority tuple values will not conflict with another LAN/Flow that is in the Assigned state.
Refer to Chapter 5 of the FSP 150CCf-825 Installation and Operations Manual to determine
the default values, value ranges and rules for each option in the following procedure.

Procedure

Step 1 Observe the

following current LAN Port Mode and EVC Mode. The status will be used in the
steps.

eVision

Select Configuration view

Expand the System Name entity in the Menu Tree

Select the LAN facility in the Menu Tree  

The LAN facility status window is displayed

WARNING — Changing EVC Mode on a facility will drop all traffic on the port,
including Management Tunnel connectivity and Maintenance End Points.

Step 2 Determine the next step.

Current Status Then

 Is the current EVC Mode set to Transparent ? Go to Step 8.

Is the LAN Port Mode set to Connection-oriented  Go to Step 6.

and EVC Mode set to Flow VLAN?
Is the LAN Port Mode set to Connection-less and Continue with the next step.
EVC Mode set to Flow VLAN?

Step 3 Enter a right click on the LAN facility and select CO Mode (Connection-oriented
Mode). 
 A warning screen appears, indicating selection of this option will cause a loss of all
traffic 

80000003806 Rev 1.0 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL Page 25

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 27/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

Step 4 Select OK. 

The EVC Mode changes to Transparent 

Step 5 Go to Step 8.

Step 6 Enter a right click on the LAN facility and select CO Transparent
(Connection-oriented Transparent mode). 
 A warning screen appears, indicating selection of this option will cause a loss of all
traffic 

Step 7 Select OK. 

The EVC Mode changes to Transparent 

Step 8 Right click on the LAN facility in the Menu Tree and select Edit Facility. 
 An edit Transparent LAN facility window appears

Figure 3 Edit Transparent LAN Facility View

Page 26 Copyright © 2008 ADVA Optical Networking - CONFIDENTIAL 80000003806 Rev 1.0

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 28/30
8/9/2019 Manual ADVA FSP 150CC-825

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 29/30
8/9/2019 FSP 150CCf-825 Quick Start Guide Manual ADVA FSP 150CC-825 TM

Release 2.1 December 2008

Optical Networking

If C-Tag Control is set to None, only one LAN port may be used in the system.

Note 6:  All C-Tag and S-Tag VLAN ID-Priority tuple values must not conflict on the WAN
port. (For example: A service with C-Tag PUSH 100-0, S-Tag PUSH 100-0 will
conflict with another service with the same C-Tag and S-Tag. A service with
C-Tag PUSH 100-0, S-Tag None will conflict with another service with C-Tag
None, S-Tag PUSH 100-0. A TLS service with C-Tag PUSH 100-0, S-Tag
NONE will conflict with a Flow with VLAN Member 100-0, C-Tag NONE and
S-Tag NONE.)

Note 7: If C-Tag or S-Tag Control is set to None, C-Tag / S-Tag VLAN ID and VLAN
Priority cannot be entered.

Step 10 Verify the changes.

Step 11 Observe the current LAN facility Assigned/Unassigned State: (The LAN facility
should still be selected in the menu tree.)
Step 12 Determine the next step.

Current Status Then

Is the current Assigned/Unassigned State set to Go to Step 14.

Enabled?
Is the current Assigned/Unassigned State set to Continue with the next step.
Disabled?

Step 13 Place the LAN facility to the Assigned state.

eVision

Enter a right click on the LAN facility in the menu tree and select Assign 
 A confirmation window appears

Select OK 
The LAN facility status window appears and the LAN Assigned/Unassigned State
is Enabled

Note: If you receive an error message indicating the CIR and/or EIR values exceed
the maximum allowed, and/or the C-Tag/S-Tag VLAN ID-Priority tuple values
conflict with existing ones, then one or more LAN values must be changed in
order to co-exist. These changes must be made by editing the LAN(s) prior to
placing this LAN to the Assigned state.

Step 14 Save the configuration in eVision by selecting File and then Save Changes from the
menu bar.

End of Procedure

http://slidepdf.com/reader/full/manual-adva-fsp-150cc-825 30/30