2 3 4 5 6

Table 3 Car call controller (MCTC-IC-A) terminal function description

1. System Overview 3. Installation 5. Commissioning
IC Card Management System User Guide 2. Product Inforamtion
The car call controller (MCTC-IC-A) is installed at the operating panel. Mark Terminal Name Function Description Commission the system when installation is completed in order to satisfy
The system consists of car call controller, card reader, card writer and IC card. ◆◆ Introduction
External 24 the requirements. Commission the system as follows:
Figure 1 System architecture of IC card management system Used to provide 24 VDC±10% power
The car call controller (MCTC-IC-A) communicates with the car top board (MCTC- Installation Method and Procedures 24+/COM VDC±10% power
supply to the controller 1. Power-on test
CTB) through RS485 bus to control floor selection authority of IC cards. The car call CN1 supply
Install as follows: Completed installation: • Use a multi-meter to measure the power supply and the voltage is 24 VDC±10%.
Single door controller provides functions: Used to connect to the car top board
MOD1+/MOD1- RS485 terminal • Insert the power supply plug into the car call controller after wiring is completed. Both the Run
◆◆Specified-floor selection (MCTC-CTB) for Modbus communication indicator D7 and the communication indicator D10 flashes. If the communication indicator D10 is
External 24 steady on, check the wiring of CN1.
◆◆Direct travel ride
24+/COM VDC±10% power
CN2 Reserved 2. System activation/deactivation IC card test
Opposite door ◆◆Floor-based service supply
• The system enters the IC card management system state with The buzzer tweets two times after
Car top board (MCTC-CTB-C2) ◆◆Swiping times-based service MOD2+/MOD2- RS485 terminal swiping the system activation/deactivation IC card. The elevator is allowed for use if you swipe
the card again with the buzzer tweets one time.
Communication
◆◆Time-based service
cable
Double color
Radio ◆◆Blacklist and records. mm LED indicator Used to connect to the double color LED 3.Administrator IC card test
.5 J6
frequency
90
connection indicator •

66.5mm
cable
The administrator IC card is for the administrators to use any elevator. Select the floor manually
Figure 2 Product front view
Card type
Double- terminal after swiping the card.
(MCTC-IC-C)
color LED
indicator R3.25mm
Key chain type
Car call controller connection Back door card
Card reader Used to connect to the card reader by 4. Swiping times-based IC card test
(MCTC-IC-C2)
(MCTC-IC-A) cable reader
J11 • Set the swiping times between 10 and 20.
(MCTC-IC-G)
4*(M4 nuts) terminal coaxial cable for opposite door elevator
Used to indicate the status when swiping
• The card can be swiped only when the swiping times are greater than zero. The swiping times
D7 RUN indicator decrease by one after each swiping.
4*(M4-12 studs) system activation/deactivation card
• The buzzer tweets one time If the remaining swiping times are greater than 10, tweets two times
USB USB
Communication Used to indicate the communication if the remaining swiping times are less than 10 and tweets for three seconds if there is no
connection connection
D10 remaining swiping times.
indicator status with car top board (MCTC-CTB).
USB key (MCTC-IC-L)
Table 4 DIP switch function description 5.Time-based IC card test
• Adjust the clock of the car call controller or check the time setting of the card when only time-
IC Card writer (MCTC-IC-W)
Card writing based IC cards are abnormal.
DIP Switch No. Function Description Example
PC
• If the time-based IC cards are still not working, replace the car call controller and set the elevator
◆◆ System Components Set elevator 1# as follows: number and clock again.

Table 1 Description of system components MCTC-IC-A MCTC-IC-A2 It is used to set the elevator ON 6.Commnicaton indicator D10
number. 8421 code (binary-coded • Communication indicator D10 flashes quickly if communication with the car top board is normal.
A00 Component Model Description Figure 3 Physical dimensions
1~7 decimal) method is used. The •
◆◆ Before power-on, check and confirm the power supply is 24 1 2 3 4 5 6 7 8 9 10 Communication indicator D10 is steady on if communication with the car top board is abnormal
Data No.: 19010508 It integrates car call controller (MCTC- corresponding codes of number 1
VDC±10%.
Car call controller MCTC-IC-A IC-A), back door card reader (MCTC- to 7 are 1, 2, 4, 8, 16, 32 and 64. Elevator 6#: 7.RUN indicator D7
IC-G1) and structural parts. ◆◆ Properly insulate the components against the ground. ON
• After swiping the system activation/deactivation IC card, the IC card management system is
It is a replacement of the car call ◆◆ Ensure the operating environment satisfies related requirements, with deactivated if the RUN indicator D7 is steady on and the buzzer tweets one time.

controller (MCTC-IC-A). Besides enough heat dissipation clearance. • After swiping the system activation/deactivation IC card, the IC card management system is
1 the card reading function, it has ◆◆ Plug in or remove the connected components when power is off. Set the button at ON side for
1 2 3 4 5 6 7 8 9 10
activated if the RUN indicator D7 flashes and the buzzer tweets two times.
27.4 mm Elevator 127# (opposite door):
an additional keypad for password opposite door elevators and set 8. Double color LED indicator
104.0 mm 24.4 mm ◆◆ Pay attention to the installation to prevent equipment damage. 9 ON
management. Users can choose to read the button at number side for
• If there is no card swiping, both the front door and back door indicators are steady on in red
Preface
101.0 mm
22.4 mm
the card directly or enter the password 90.0 mm single door elevators. color.
for elevator call. 4. Wiring • After swiping the card, the corresponding indicator flashes in green color and the other indicator
Thank you for choosing MONARCH IC card management system for elevators. 1 2 3 4 5 6 7 8 9 10
Car call controller with remains the same.
MCTC-IC-A2 The keypad supports the operations:
This is a new-generation IC card management system independently developed and keypad R3.25 mm ◆◆ Function Description of Terminal and DIP Switch Description of elevator number:
• The indicator flashes in red and green colors alternatively at a 2s interval when the records are
manufactured by Suzhou Inovance Technology Co., Ltd., by optimizing the previous Users can set and change the password. being erased.
Figure 4 MCTC-IC-A diagram
generation based on a large number of applications and combining new industrial If the password is forgotten, users reset Ø5.5 mm ◆◆ Elevator No.: The IC card holder can only use the corresponding

66.0 mm
77.0 mm
elevator.

80.0 mm
features. the password by using a replacement IC D1: Double color LED
Indicator ◆◆ The elevator number set by DIP switch prevails the elevator number
card.
Before using this product, read this manual carefully to fully understand features
set by system setting IC card.
Warranty Agreement
of the product and ensure safe use. This user guide describes product features, The administrator can set a password
◆◆ The elevator number can be set whether the power of car call
mounting dimensions, terminals, installation, commissioning and application to activate or deactivate the IC card 1. The warranty period of the product is 18 months (refer to the barcode on the
J6: Double color LED
controller is on or off. The DIP switch No.8 and No.10 are reserved
examples. These information is for your reference. management system. MCTC-IC-A indicator connection
equipment). During the warranty period, if the product fails or is damaged under the
terminal and turned off by default.
It is for the back door of opposite door J11: Card reader interface to condition of normal use by following the instructions, Inovance will be responsible
Back door card reader MCTC-IC-G connect to the CTB
elevators.
Product Features ◆◆ Application and Wiring for free maintenance.
D1: Double color LED
It connects to the PC to configure IC Figure 5 MCTC-IC-A/MCTC-IC-A2 wiring diagram
Comparison between the new system and the previous system IC card writer MCTC-IC-W ◆◆ Technical Specification Indicator
2. Within the warranty period, maintenance will be charged for the damages caused
cards.
It connects to the PC to unlock the Table 2 Car call controller (MCTC-IC-A) technical specifications J1 by the following reasons:
Features Previous System New System
USB key MCTC-IC-L
software. J6 a. Improper use or repair/modification without prior permission
The controller and card The controller and card reader are Item Specification MCTC-IC-G
Integration MCTC-IC-C Card type MCTC-IC-A CN2: Reserved (Back door card reader) b. Fire, flood, abnormal voltage, other disasters and secondary disaster
reader are separate. integrated. Car top board
IC card Input voltage 24 VDC±10% CN1: Communication terminal (MCTC-CTB)
MCTC-IC-C2 Key chain type c. Hardware damage caused by dropping or transportation after procurement
The IC card cannot be Input current < 300 mA
for car top board (MCTC-CTB)
The IC card is encrypted individually
Safety encrypted and might be 24V MOD+ MOD- COM d. Improper operation
and cannot be copied. Response time < 100 ms
copied. DIP switch e. Trouble out of the equipment (for example, external device)
Basic specifi- Maximum quantity of stored card swiping
◆◆ Double color indicator 9322 CN1 3. The maintenance fee is charged according to the latest Maintenance Price List of
cations records D7: RUN indicator 24V J11
MOD1+
◆◆ Using system setting IC card to set MOD1- Inovance.
User Friendless It is less user friendly. Maximum quantity of IC cards 1024 COM J6
elevator number Car call controller
Maximum quantity of elevators 127 sets
CN2
(MCTC-IC-A) 4. If there is any problem during the service, contact Inovance’s agent or Inovance
24V
◆◆ Less wiring, plug and play D10: Communication indicator MOD2+
Length of coaxial cable 5m 24V MOD+ MOD- COM MOD2- directly.
COM

5. This agreement shall be interpreted by Suzhou Inovance Technology Co., Ltd.

Operating temperature –10°C to +60°C Hall call board
Access to Latest Manual (MCTC-HCB)
30%–95% RH
Humidity
This manual is subject to change without notice. If you need the latest manual: Environment non-condensing

◆◆Contact with the sales agent, or Storage temperature –20°C to +70°C

◆◆Visit the official website: www.inovance.cn. ◆◆ The car call controller uses the 24 VDC±10% power supply of car top
Suzhou lnovance Technology Co., Ltd.
board or hall call board.
Address: No.16, Youxiang Road, Yuexi Town,
◆◆ The car call controller communicates with the car top board through Wuzhong District, Suzhou 215104, P.R.China
RS485 bus. Connect the car call controller to the RS485 terminal of http: //www.inovance.cn
the car top board or hall call board accordingly.