RGB CONVERTER

SPECIFICATION

-. MODEL: RGB-LE-V3
-. PRODUCT CODE : RB-080125-013

www. car-solutions.com
 INDEX

-. Pre-Caution
-. Main Specification
-. System Composition Map
-. Out-Line Dimension
-. MODULE EXTERNAL
-. Connector Pin Assignment
-.. DIP SW Operation Process
-. Remote Control Guide
-. Products composition
-
-. FAQ
-Pre-Caution
- You must keep the car key taken off from the car while you work this and finally,
connect power of the interface.

- When to connect the interface cable, you must keep the power cable taken off.

- You must work this at the environment without any static electricity or damages.

- All of process on this installation should be done by professionals.

- You must not break the labels attached on the board, if it’s broken, no warranty.

- When you receive this package you have to check whether there’s any parts not
included and you have to contact us right away.

- Our
O repair
i service
i d do not accept any problems
bl caused
d by
b user’s
’ any fault
f l or carelessness.
l
-Main Specification
p
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 2 x CVBS Input (External video source).
-. 1 x CVBS (REAR CAMERA) Input (Rear camera source)
- 1 x Analog RGB Input (Car commander original monitor output)
-.
-. 1 x Analog RGB Input (Navigation System output)-ÆOPTION

2. Output Spec.
-. 1 x CVBS OUTPUT (Video Out for installing Headrest monitor)
-. 1 x RGB OUTPUT(LCD O Operation)
i )
-. 1 x Audio Select OUTPUT (For operating A/V sources – ex) 12V is come out on V1 port, when
AV1 is chosen.)

3. Power Spec.
p
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 5WATT, Max

4. Switch Input mode

- NAVI/CVBS1,2
NAVI/CVBS1 2 Original MUTE Function : Possible to mute each input by operating Dip S/W
- Possible to switch Input mode with remote control or toggle switch.
- Rear View Camera mode : When to sense rear gear power, be switched to Rear view camera
mode (Impossible to switch to rear mode with Toggle S/W or the
Remote control)

5. Special Function
- Remote Key scanning function (Option – If you want to use this function, you have to
purchase the remote additionally.)
* How to use?
Press 4291 buttons of Remote offered, then LED lamp of interface blinks. After that, press
any button of A/V source remote such as Navigation, DVD etc. that you want to use. If LED
lamp of the interface blinks slowly, It means to succeed and you can use the button that you
set for mode change.
-System
y Composition
p Map
p
Remote ControlSwitch for source toggle & REAR SENSE

NAVIGATION Input MCU

(Analog RGB)

CVBS1 DISPLAY CAR Installation

OEM LCD
CVBS2
VIDEO
CVBS CIRCUIT
(Rear camera) VIDEO MUX

Car Screen Input

(CAR MAIN BOARD)
POWER CVBS OUT
CIRCUIT HEADREST
MONITOR

Power Input Dip S/W

(+8VDC ~ +24VDC)
-Out-Line
Out Line Dimension
129mm * 75mm * 21mm
129mm

75mm

21mm
21

※ This can change under manufacturer's circumstance

-Module External
LED AUDIO-SEL DIP S/W RGB(OUT) OEM(IN) NAVI(IN)

V-Out
POWER MODE IR V1 V2 R/V

※ This can change under manufacturer's circumstance

-Module External
NAVI(IN) OEM(IN) RGB(OUT) DIP S/W ADO-SEL

POWER MODE IR V1 V2 R/V V OUT

V-OUT

※ This can change under manufacturer's circumstance

-Connector Pin Assignment
g

*NAVI-IN Connect *RGB-OEM Connect *RGB-OUT Connect

① ② ③ ④ ⑤ ⑥ ⑦
①②③④⑤⑥⑦⑧⑨⑩
① ② ③ ④ ⑤
① R DATA ① B Data : Blue
② G DATA ① R Data : Red ② G Data : Green
③ B DATA ② G Data : Green ③ R Data : Red
④ SYNC ③ B Data : Blue ④ Sync Data : White
⑤ GND ④ Sync : White ⑤ GND : Black
⑥ NAVI IR ⑤ GND : Black ⑥ ACC : Yellow
⑦ DVD IR ⑦ Video S/W : Orange
⑧ Not used

※ This can change under manufacturer's circumstance

-Connector Pin Assignment
g

*Power Connect
⑤
⑥ ④

③ ①
②
① GND (
② I -Drive
③ F MTX
④ N.C
⑤ ACC
⑥ R EAR

※ This can change under manufacturer's circumstance

 -Connector Pin Assignment
g
* Power cable

FILTER
& FUSE BOX

Orange
I - DRV
Gray Black
GND
990
990mm
Orange
Red
Red ACC
Black Gray LAMP - RV
990mm
 -DIP
DIP SW Operation Process
※ ON : DOWN, OFF : UP
※DIP S/W Use Example
#PIN FUNCTION DIP S/W Selection [W211]
ON : Skipping RGB Mode -. Use Input Mode : CVBS1, Navigation (RGB), Main
1 RGB INPUT MUTE
OFF : RGB Display -. Rear Camera : When to be installed on CVBS 4
ON : Skipping CVBS1 ▷ DIP S/W : 1 Æ OFF
2 CVBS1 MUTE
OFF : CVBS1 Display ▷ DIP S/W : 2 Æ OFF
ON : Skipping CVBS2 ▷ DIP S/W : 3 Æ ON
3 CVBS2 MUTE ▷ DIP S/W : 4 Æ OFF (All of the Car except Cayenne)
OFF : CVBS2 Display
p y
▷ DIP S/W : 5 Æ OFF
ON : When install to the Cayenne ▷ DIP S/W : 6 Æ OFF
4 CAN ▷ DIP S/W : 7 Æ ON (enable CVBS4)
OFF : When install to all of the car
▷ DIP S/W : 8 Æ OFF
ON : Skipping OEM
5 OEM MUTE
OFF : OEM Display
ON : Non-Interlace
6 INTERLACE
OFF : Interlace
ON : External Rear Camera
7 REAR MODE
OFF : OEM Rear Camera
* Caution
8 SYNC ON GREEN
ON : Sync On Green (RGSB) - If the displayed screen vibrates, please try to
OFF : Sync On Green Off operate Dip S/W No. 6 after turning power off.
-Remote
Remote Control Guide
Power : Mode is changed on only headrest monitor by this button, when front
monitor shows Navigation or Rearview camera, Main.
Source : When to change mode, you can change mode by this button.

Navi : To change mode to Navigation directly

AV1 : To change mode to A/V source you connected to A/V1 directly

AV2 : To change mode to A/V source you connected to A/V2 directly

AV3 : To change mode to A/V source you connected to A/V3 directly

▲ : Increasing

OK : Select

▼ : Decreasing

Menu : To enable OSD Menu

4:3 : To convert screen rate from 4:3 to 16:9 or 16:9 to 4:3

Main : To change to Main mode directly

Scan : Not available

Mute : Not available

Disp : Currency A/V source screen display

Reset : To make all value to factory default.

Cont. : To adjust Color under OSD (Hot Key)

Brt. : To adjust Brightness under OSD (Hot Key)

-Products
Products composition

Power cable : 1 Audio Select Cable: 1

Mode cable : 1 RGB NAVI : 1
RGB(Out) cable : 1 IR Cable : 1
RGB OEM : 1 R
Remote
t Control
C t l:1
Installation Structure
V
i
d
MONITOR e
S o S S
Y GA SN yG y G
NN C / . nN nN
O O BG R C D C WC RG B c D R G B cD
Offered U U
FFC T T
P P
U U
T T
1 2

LED ADO-SEL DIP S/W RGB(OUT) OEM(IN) NAVI(IN)

Original
FFC

RGB CONVERTER(LE)
Control Box

POWER MODE IR V1 V2 R/V V-OUT

ACC

LAMP-
RV

FMTX
Solder this wire to the Head
I-DRV Unit for changing mode by
original button
GND (Only for Cayenne, W164EU,
W211)
 -FAQ
FAQ
1. When can not change mode.
-. Check if the IR Cable (remote control) is connected or not.
-. Check if LED is turned on or not. If it is not turned on,, Check if p
power cable is connected or not.

2. When the screen is displaying only black color.

-. Check if 2nd LED is turned on or not. If it is not turned on, please check the sources that you will connect with the
interface is operating well or not.
-. Check if interface is connected well.

3. When displayed color of screen is not proper. (If it’s too dark or the color is not proper)
-. Try to push “Reset button” on the remote control. If the color of screen keeps on displaying wrong color, you have
to ask manufacturer for the problem.

4. Wh
4 When B Back-up
k camera is
i nott di
displayed
l d on th
the screen.
-. Turn Dip S/W no.7 on.

5. When the mode you set is not skip.

-. Check if Dip S/W is set in proper way.

6. When Main screen on the car is not displayed.

-. Check if In/Out cables are connected well. If it keeps showing the same problem, you have to
ask manufacturer for the problem.

7. When the screen is displaying only white color

7 color.
-. Check if out cable is connected well. If it keeps showing the same problem, you have to ask
manufacturer for the problem.

8. The case the screen is changed to Main mode despite of choosing Back-up camera mode.
-. Check if Dip S/W no
no.7
7 is turned on
on. If it’s
it s not
not, you have to turn it on
on.

9. When the screen is blinking or not proper.

-. Turn Dip S/W no.6 on.