Scribd
Upload
338 views

ISC Learning Procedure

Uploaded by

გიორგი ჯიქიძე
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
338 views

ISC Learning Procedure

Uploaded by

გიორგი ჯიქიძე
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 3
Ovrsxus Technical Service Information Bulletin August 25, 2007 ‘ANIONS, Isc LEARNING PROCEDURE Models: ’08 RX 400h Introduction When the 12.vot batery is disconnected or is depleted below 7 volts on 2008 model year RX 400h vehicles, itis necessary to perform the ISC Learning procedure to re-iniialize the idle speed control, The information in this TSIB relates to this procedure Applicable» 2008 model year RX 400h vehicles. Nebel Required REQUIRED EQUIPMENT Toots Equipment | TIS Techstream* NOTE: Sofware vonion2 100 Pore fe 7 | Aaational Techttear units may bo ordered by caling Approved Desir Equipment | | Gabe) at 200 aeserar Warranty [op cope DESCRIPTION TIME ‘OFP Sen NA Not Applicable to Warranty ISC LEARNING PROCEDURE - £6021 ISC Learning Procedure Page 2013. 7 August 25, 2007 !tis important to perform the ISC Learning procedure anytime the 12-volt battery is disconnected or the voltage falls below 7 volts. This procedure allows the internal ‘combustion engine to relearn its optimal idle speed during the initial engine warm-up cycle or charging the HV battery. If this procedure is NOT performed, the following customer complaints may occur: + Engine runs too long or more frequently than normal + Reduced fuel economy + Transmission gear “clatter” noise at idle is more pronounced In TIS Techstream, the current state of ISC Leaming status can be accessed through the following path: Powertrain/Engine/Data ListiISC Learning ISC Learning value identifies the current status of ISC Learning and is expressed as either "COMPL” (complete) or “INCOMP" (incomplete). Each time the ignition is cycled to the “OFF* position, the ISC Leaming value will show “INCOMP” unti the engine completes its initial startup/shutdown. Use the following procedure to verify the current status of the ISC Learning: 1. Drive the vehicle unti the engine reaches operating temperature 158°F (70°C) (can be accessed through TIS Techstream: Powertrain/Engine/Data List Coolant Temp). 2. Park the vehicle and tun the ignition OFF. 3. Access the ISC LEARNING data parameter (Powertrain/Engine/Data List! ISC Learning), 4, Tum the ignition key back to “READY ON” 5. Wait for the engine to start and run through its intial startup cycle and shut OFF. 6. Observe the ISC Learning status. Ifthe vehicle shows *INCOMP” after intial engine shutdown in step §, then the ISC. Initialization Procedure should be performed, ISC LEARNING PROCEDURE Isc Initialization Procedure G02 August 25, 2007 1. Connect TIS Techstream to the vehicle, 2. Select the following menu items: Powertrain/Engine/Data ListCoolant Temp 3. Check that the engine coolant temperature is 181°F (83°C) or more. [mw 1 the engine coolant temperature i below 181°F (83°C), start the engine by depressing the acolerator pedal withthe shift lever nthe “P" postion we yerease the coolant temperature 4, Select the following menu items: Powertrain/Hybrid Control/Data List/Calculate Load 8. Move the shift lever to the “D" position while depressing the brake pedal with the LEFT foot, &. Depress the accelerator pedal with the right foot while fly depressing the brake Pedal with the left foot, and maintain an engine load value of 45% or more (60 - 70% of full acceleration) for approximately 30 seconds. 7. Shift the lever to the “P* position. Turn the ignition switch OFF and then wait for © seconds before putting the vehicle into the “READY ON" state ag 8. Select the following menu items: Powertrain/Engine/Data List/ISC Learning 8. Check that the air conditioner is OFF, Lightly depress the accelerator pedal and release it when the engine starts. 10. Check that COMPLETE" is displayed on the TIS Techstream screen, ot |. + IISC LEARNING® Io NOT completed within 1 minut, repeat stops 4-8 + The engine wil usally stop when the “SC LEARNING” is completed, However, the |” tnsine wt Nor sop even te te ice ean combed Ho |__statetrcharge of he aunlarybatery flow Page 30f3

You might also like