Scribd
Upload
65 views

Method Statement For Plumbing System HDPE Drainage System

The document provides a method statement for installing and testing an underground HDPE drainage piping system. It outlines the materials used, which are HDPE pipes and fittings. It also lists the applicable equipment. The method includes storing and handling pipes properly, fabricating and marking pipe locations, bedding and backfilling, and performing a water pressure test to check for leaks.

Uploaded by

Walid
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
65 views

Method Statement For Plumbing System HDPE Drainage System

The document provides a method statement for installing and testing an underground HDPE drainage piping system. It outlines the materials used, which are HDPE pipes and fittings. It also lists the applicable equipment. The method includes storing and handling pipes properly, fabricating and marking pipe locations, bedding and backfilling, and performing a water pressure test to check for leaks.

Uploaded by

Walid
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

Method Statement for Plumbing System

HDPE Drainage System

Rev. Description Date Prepared By Reviewed Approved Approved


By By By

Page 1 of 4
1.0 Scope

1.1 This method statement details the method for installation and testing of
underground HDPE drainage piping.

2.0 Material

2.1 For pipeline

HDPE pipes and Fittings .

2.2 Equipment

1-Hand tools 2-Cutting machine

3-Welding machine 4-Heater

3.0 Applicable Location

for underground drainage pipes.

4.0 Method

4.1 Storage

4.1.1 When off loading pipes shall be lowered to the ground either manually
or with mechanical aid like crane depending on the quantity of the pipe
and should not be dropped to the ground. Refer – Manufacturer’s
instruction for transport, handling and storage.

4.1.2 Pipes shall be stacked on a flat surface free from any sharp objects.

4.1.3 Pipes shall not be stored under direct sunlight to avoid ultra violet
degradation.

4.2 Installation

A. Pipe fabrication:

 Fabricate pipe as much as you can in the workshop according to sizes as per
drawings to be ready for installation.

 Mark the location of pipes with the help of the surveyor.

 The location of pipe will be determined according to approved shop


drawings.

Page 2 of 4
 After the completion of marking points ,fix the line with the
required levels.

 Start bedding of fine sand before install the pipes.

 After the excavation and bedding ,the surface shall be Clean


and suitable for starting pipe installations.

4.3.11 To avoid possible damage or deformation of the pipe ,compacted layer


shall be without hard stones .

4.4 Back-Filling

4.4.1 Filling around the pipes shall be done with the same bedding material
and be throughly compacted.

Page 3 of 4
5. Testing

5.1 Water test is conducted to ensure and prove the tightness of the joints and
ensure there are no leaks in the piping system.

5.2 The water pressure test can be applied to the system in its entirety or in sections.
All openings in the piping will be tightly closed, the system filled with water to
the point of overflow from the highest point. The plugs can be temporally
opened to make sure that all air has been vented and that water has reached all
parts of the system.

5.3 No section of the pipe shall be tested to less than 1.5-meter head of water.

5.4 The water shall be kept in the system or in the portion under test for at least 30
minutes before inspection starts. While the system is under pressure, a careful
inspection shall be made on all pipes and joints. If any leaks in joints or
evidence of defective pipe or fittings is revealed, the defective pipe / fitting
should be immediately replaced with new joints and materials.

5.5 After the correction is made, the test pressure will be maintained for minimum
30 minutes.

5.6 After approval of testing back filling will be allowed.

Page 4 of 4

You might also like