TESDA-OP-QSO-02-F07

Rev. No. 00 03/01/17

Reference. No.

SELF - ASSESSMENT GUIDE

Qualification: CARPENTRY NC II
 Layout reference lines
 Fabricate, install and remove wooden formworks
 Install wooden door jamb, window frame and panels
Unit of
 Install ceiling and wall frames and panels
Competency
 Fabricate and Install wooden stairs
covered:
 Install wooden floor supports and panels
 Fabricate and install roofing system
 Fabricate and install wooden cabinet
Instruction:
 Read each of the questions in the left-hand column of the chart.
 Place a tick in the appropriate box opposite each question to indicate your answer.

Can I? YES NO

Prepare materials and hand tools *

 Use personal protective equipment (PPE) in accordance with
Rule 1080 of Occupational Safety and Health Standards
 Select, inspect and prepare materials and hand tools consistent
with job requirements
Locate offset line established by the line and grade/ surveyor *
 Follow related sketches and working drawings according to job
requirements
 Locate and verify offset line/ building line

Establish required reference line *

 Mark initial lines from offset lines in accordance with working
drawings.
 Mark, square and plumb final reference lines in accordance with
working drawings
 Place subsequent markings as required

Lay-out and cut dimension of form sheathings and stiffeners *

 Measure and mark form sheathings and stiffeners according to
job specifications.
 Lay out and cut form sheathings and stiffeners according to
required dimensions.

CONCAR218-0719 ver. 1.00

1
Carpentry NC II
Assemble and erect form panels and components *

 Position and fix sheathings to stiffeners

 Check assembled form panels for squareness, levelness,
plumbness and alignment.
 Position and fix primary and secondary supports to hold
assembled form panels as per drawings.
 Check assembled form panels for compliance with job
requirements.
Layout location *
 Marks exact location for door and window opening based on
working drawing
 Checks clearance of opening based on working drawings

Fix door jamb and panels *

 Select and check assembled jamb and panels for compliance
with job requirements
 Temporarily position jamb to hold assembled panels as per
drawings.
 Check installed jamb and panels for squareness, levelness,
plumbness and alignment
 Position and fix jamb and panels to openings
Layout ceiling elevation, wall location and position of framing
system*
 Mark exact layout for ceiling and wall frames based on working
drawings
Fix frames and panels*

 Install frames based on specifications

 Check installed frames for squareness, levelness, plumbness
and alignment.
 Fix panels to frames based on working drawings

Layout location and stair elevation *

 Mark exact location of stairs including riser and thread based on
working drawings
Place wooden stringer, thread, handrails and baluster *
 Cut and fabricate wooden stringers based on working drawing
and/or actual requirements
 Position and fix wooden stringer and thread based on working
drawings.

CONCAR218-0719 ver. 1.00

2
Carpentry NC II
 Check wooden stairs assembly for stability and firmness.

Layout truss location and elevation *

 Mark exact location for roof truss assembly based on working
drawing
Place wooden roof truss assembly, purlins and fascia board *
 Position and fix wooden roof truss assembly according to job
requirements
 Check alignment of all installed wooden roof truss assembly
based on job requirements
 Install purlins as per required spacing

Perform Housekeeping *
 Recovers and stockpile materials such as excess/un-used
materials according to company rules and procedures
 Cleans and clears workplace of any obstructions and hazards
before, during and after work
 Cleans tools, equipment and other materials after use

I agree to undertake assessment in the knowledge that information gathered will only
be used for professional development purposes and can only be accessed by
concerned assessment personnel and my manager/supervisor

Candidate’s Name & Signature Date

CONCAR218-0719 ver. 1.00

3
Carpentry NC II
 TESDA-OP-QSO-02-F07
Rev. No. 00 03/01/17

Reference. No.

SELF - ASSESSMENT GUIDE

Qualification: CARPENTRY NC II

COC 1: FABRICATE, INSTALL AND REMOVE WOODEN FORMWORKS

Instruction:
 Read each of the questions in the left-hand column of the chart.
 Place a tick in the appropriate box opposite each question to indicate your answer.

Can I? YES NO

Prepare materials and hand tools *

 Use personal protective equipment (PPE) in accordance with
Rule 1080 of Occupational Safety and Health Standards
 Select, inspect and prepare materials and tools consistent with
job requirements
Lay-out and cut dimension of form sheathings and stiffeners*
 Measure and mark form sheathing and stiffeners according to
job specifications.
 Lay out and cut form sheathing and stiffeners according to
required dimensions.
Assemble and erect form panels and components*
 Position and fix sheathings to stiffeners
 Check assembled form panels for squareness, levelness,
plumbness and alignment.
 Position and fix primary and secondary supports to hold
assembled form panels as per drawings.
 Check assembled form panels for compliance with job
requirements.
Clean and store reusable form panels and components*
 Recover and stockpile materials such as excess/un-used
materials according to company rules and procedures
 Clean and clear workplace of any obstructions and hazards
before, during and after work
 Clean tools, equipment and other materials after use
I agree to undertake assessment in the knowledge that information gathered will only
be used for professional development purposes and can only be accessed by
concerned assessment personnel and my manager/supervisor

Candidate’s Name and Signature Date

NOTE: *Critical aspects of competency
CONCAR218-0719 ver. 1.00
1
Carpentry NC II
 TESDA-OP-QSO-02-F07
Rev. No. 00 0/01/17

Reference. No.

SELF - ASSESSMENT GUIDE

Qualification: CARPENTRY NC II
Install door and window assembly; install ceiling and wall
COC 2:
system; and fabricate and install wooden cabinet
Instruction:
 Read each of the questions in the left-hand column of the chart.
 Place a tick in the appropriate box opposite each question to indicate your answer.

Can I? YES NO

Prepare materials and hand tools*

 Use Personal protective equipment (PPE) in accordance with
Rule 1080 of Occupational Safety and Health Standards
 Select, inspect and prepare materials and tools consistent with
job requirements
Locate offset line established by the line and grade/ surveyor*
 Follow related sketches and working drawings according to job
requirements
 Locate and verify offset line/ building line

Establish required reference line*

 Mark initial lines from offset lines in accordance with working
drawings.
 Mark, square and plumb final reference lines in accordance with
working drawings
 Places subsequent markings as required

Fix door jamb and panels*

 Select and check door jamb assembly and panels for compliance
with job requirements
 Temporarily position jamb to hold assembled panels as per
drawings.

CONCAR218-0719 ver. 1.00

2
Carpentry NC II
 Check installed jamb and panels for squareness, levelness,
plumbness and alignment
 Position and fix jamb and panels to openings
Layout ceiling elevation, wall location and position of framing
system*
 Mark exact layout for ceiling and wall frames based on working
drawings
Fix frames and panels*

 Install frames based on specifications

 Check installed frames for squareness, levelness, plumbness
and alignment.
 Fix panels to frames based on working drawings

Perform Housekeeping*
 Recover and stockpile materials such as excess/un-used
materials according to company rules and procedures
 Clean and clear workplace of any obstructions and hazards
before, during and after work
 Clean tools, equipment and other materials after use

I agree to undertake assessment in the knowledge that information gathered will only
be used for professional development purposes and can only be accessed by
concerned assessment personnel and my manager/supervisor

Candidate’s Name and Signature Date

NOTE: *Critical aspects of competency

CONCAR218-0719 ver. 1.00

3
Carpentry NC II
 TESDA-OP-QSO-02-F07
Rev. No. 00 0/01/17

Reference. No.

SELF - ASSESSMENT GUIDE

Qualification: CARPENTRY NC II

COC 3: Fabricate and Install Stair, Floor System and Truss assembly

Instruction:
 Read each of the questions in the left-hand column of the chart.
 Place a tick in the appropriate box opposite each question to indicate your answer.

Can I? YES NO

Prepare materials and hand tools*

 Use personal protective equipment (PPE) in accordance with
Rule 1080 of Occupational Safety and Health Standards
 Select, inspect and prepare materials and hand tools consistent
with job requirements
Layout truss location and elevation*

 Mark exact location for roof truss assembly based on working

drawing
Place wooden roof truss assembly and purlins *
 Position and fix wooden roof truss assembly according to job
requirements
 Check alignment of all installed wooden roof truss assembly
based on job requirements
 Install purlins as per required spacing

Layout location and stair elevation*

 Mark exact location of stairs including riser and thread based on

working drawings

Place wooden stringer, thread, handrails and baluster *

 Cut and fabricate wooden stringers based on working drawing and/or

actual requirements
 Position and fix wooden stringer and thread based on working
drawings.

 Check wooden stairs assembly for stability and firmness.

CONCAR218-0719 ver. 1.00

4
Carpentry NC II
Perform Housekeeping*
 Recover and stockpile materials such as excess/un-used
materials according to company rules and procedures
 Clean and clear workplace of any obstructions and hazards
before, during and after work
 Clean tools, equipment and other materials after use

I agree to undertake assessment in the knowledge that information gathered will only
be used for professional development purposes and can only be accessed by
concerned assessment personnel and my manager/supervisor

Candidate’s Name and Signature Date

NOTE: *Critical aspects of competency

CONCAR218-0719 ver. 1.00

5
Carpentry NC II