DESIGN OF SLABS

A. DESIGN PARAMETERS

𝑓^′ 𝑐= 20.7 MPa

𝑓𝑦= 415 MPa

𝑈𝑛𝑖𝑡 𝑤𝑒𝑖𝑔ℎ𝑡 𝑜𝑓 𝐶𝑜𝑛𝑐𝑟𝑒𝑡𝑒= 23.6 KN/cu.m

𝑀𝑖𝑛. 𝑡ℎ𝑖𝑐𝑘𝑛𝑒𝑠𝑠 𝑜𝑓 𝑆𝑙𝑎𝑏= 100 mm

𝑀𝑎𝑥𝑖𝑚𝑢𝑚 𝑆𝑝𝑎𝑐𝑖𝑛𝑔 𝑜𝑓 𝑅𝑒𝑖𝑛𝑓𝑜𝑟𝑐𝑒𝑚𝑒𝑛𝑡:

𝑆_𝑚𝑎𝑥=2ℎ (𝑇𝑤𝑜−𝑊𝑎𝑦 𝑆𝑙𝑎𝑏)

𝑆_𝑚𝑎𝑥=3ℎ (𝑂𝑛𝑒−𝑊𝑎𝑦 𝑆𝑙𝑎𝑏)

𝑀𝑎𝑥. 𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒 𝑑𝑒𝑓𝑙𝑒𝑐𝑡𝑖𝑜𝑛= 𝐿/480

**Properties of Beam:

𝑑= 318 mm
𝑊_𝑓= 0.308 m
𝑡_𝑓= 20.6 mm
𝑡_𝑤= 13.1 mm

B. THICKNESS OF SLAB

**Two - Way Slabs

ℎ= ( 〖 2𝐿 〗 _𝑎+
〖 2𝐿 〗 _𝑏)/180

** For 4m x 6m Slabs
𝐿_𝑎=4𝑚 −2(𝑊_𝑓/2)

𝐿_𝑎= 3.692 m
𝐿_𝑏=6𝑚 −2(𝑊_𝑓/2)

𝐿_𝑏=
5.692 m

ℎ= ( 〖 2𝐿 〗 _𝑎+
〖 2𝐿 〗 _𝑏)/180

ℎ= 0.104 m
ℎ= 104 mm
mm
DESIGN OF SLABS
 mm
say, 110

** For 4m x 3m Slabs
𝐿_𝑎=3𝑚 −2(𝑡_𝑓/2)

𝐿_𝑎=
2.692 m
𝐿_𝑏=4𝑚 −2(𝑡_𝑓/2)

𝐿_𝑏=
3.692 m

ℎ= ( 〖 2𝐿 〗 _𝑎+
〖 2𝐿 〗 _𝑏)/180

ℎ= 0.071 m
ℎ= 71 mm
mm
say, 80

Thefore, use:
h=m110
m

DESIGN OF SLABS
0.15

DESIGN OF SLABS
 DEAD LOAD
(NSCP 2015: TABLE 204-2, MINIMUM DESIGN DEAD LOADS)
LOADS SLAB 1 SLAB 2 SLAB 3 SLAB 4 SLAB 5 SLAB 6
CEILING:ACOUSTICAL FIBER BOARD
A. 0.05 0.05 0.05 0.05 0.05 0.05
0.05KPa
WATERPROOFING MEMBRANES: LIQUID
B. 0 0 0.05 0 0 0
APPLIED (0.05KPa)
ACCESS TO FLOOR SYSTEM
C. 0.5 0.5 0.5 0.5 0.5 0.5
0.50KPa
FLOOR FINISH: CERAMIC OR QUARRY TILE
D. 1.1 1.1 1.1 1.1 1.1 1.1
1.100KPa
WEIGHT OF SLAB:
E. 2.596 2.596 2.596 2.596 2.596 2.596
(23.60KN/cu.m)(
TOTAL: 4.246 4.246 4.296 4.246 4.246 4.246

LIVE LOAD
(NSCP 2015: TABLE 205-1, MINIMUM UNIFORM AND CONCENTRATED LIVE LOADS)
LOADS SLAB 1 SLAB 2 SLAB 3 SLAB 4 SLAB 5 SLAB 6
WARDS AND ROOMS
A. 1.9 1.9 0 0 0 0
1.900KPa
RESTROOMS
B. 0 0 2.4 0 0 0
2.400KPa
CORRIDOR ABOVE GROUND FLOOR
C. 0 0 0 3.8 3.8 3.8
3.8 Kpa
TOTAL: 1.900 1.900 2.400 3.800 3.800 3.800

DESIGN OF SLABS
0.15

DESIGN OF SLABS
SLAB 1:

A. LOADINGS

DL = 4.246 KPa
LL = 1.900 KPa

**Factored Load

1.2 DL = 5.095
1.6 LL = 3.040

𝑊_𝑢=1.2 𝐷𝐿+1.6𝐿𝐿
𝑊_𝑢= 8.135 Kpa

B. CALCULATE FACTORED MOMENT

𝐿_𝑎=4𝑚 −2(𝑡_𝑓/2)

𝐿_𝑎= 3.692 m
𝐿_𝑏=6𝑚 −2(𝑡_𝑓/2)

𝐿_𝑏= 5.692 m
𝐿_𝑎/
𝐿_𝑏 = 0.649

**Interpolation of Coefficient (Case 4)

Deadload Positive Moment

Ca
Ratio Value
0.6 0.053
0.649 0.050082
0.65 0.05

Cb
Ratio Value
0.6 0.007
0.649 0.008945
0.65 0.009

Live load Positive Moment

Ca
Ratio Value
0.6 0.067

DESIGN OF SLABS
 0.649 0.062137
0.65 0.062

Cb
Ratio Value
0.6 0.009
0.649 0.010945
0.65 0.011

Negative Moment at Continuous Edge

Ca
Ratio Value
0.6 0.089
0.649 0.085110
0.65 0.085

Cb
Ratio Value
0.6 0.011
0.649 0.014890
0.65 0.015

**Positive Moment

Short Direction
𝑀_𝑎 𝐷𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 3.478
𝐷𝐿=
𝑀_𝑎 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 2.575
𝐿𝐿=
𝑀_𝑎 6.053
=
Long Direction
𝑀_𝑏 𝐷𝐿=𝐶_𝑏 𝑊_𝑢
〖𝐿 _𝑏 〗 ^2
𝑀_𝑏 1.477
𝐷𝐿=
𝑀_𝑏 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑏 1.078
𝐿𝐿=
𝑀_𝑏 2.555
=
**Negative Moment at Continuous Edge

𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎=

DESIGN OF SLABS
 𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎= 9.438

𝑀_𝑏=𝐶_𝑏 𝑊_𝑢 〖𝐿 _𝑏 〗
^2
𝑀_𝑏= 3.925
**Negative Moment at Discontinuous Edge

𝑀_𝑎=1/3(𝑃𝑜𝑠𝑖𝑡𝑖𝑣𝑒 𝑀𝑜𝑚𝑒𝑛𝑡)

𝑀_𝑎= 2.018

𝑀_𝑏= 0.852

C. Examine the Depth of Slab

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑑=√(𝑀𝑢/
(∅𝑏𝑅𝑢))

**Where:

𝑅_𝑢=𝑓^′ 𝑐𝜔(1−0.59𝜔)
𝜔=(𝜌_𝑚𝑎𝑥 𝑓𝑦)/(𝑓^
′ 𝑐)

𝜌_𝑚𝑎𝑥=0.75((0.85𝑓^′ 𝑐𝛽_1
(600))/(𝑓𝑦(600+𝑓𝑦)))

𝜌_𝑚𝑎𝑥= 0.015977

𝜔= 0.3203202
𝑅_𝑢= 5.378
𝑀_𝑢= 9.438× 〖 1 (Maximum Moment)
∅= 0〗^
0.96
𝑏= 1000 mm (1m Strip)

𝑑= 44.159 mm

D. Effective Depth of Slab

𝑑=ℎ −20 −12/2

𝑑= 84.000 mm

Therefore, use:
𝑑= 84.000 mm

DESIGN OF SLABS
E. CALCULATE AREA OF STEEL AND SPACING

MIDDLE STRIP

𝜌_𝑎=𝐴𝑠/𝑏𝑑

𝜌_𝑎=(0.85𝑓^′ 𝑐)/𝑓𝑦 [1−√(1−2𝑅𝑢/(0.85𝑓^′

𝑐)) ]

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑆_1=(1000
𝜋𝐷^2)/(4𝐴_𝑆 ) ;D = 12 mm

𝑆_𝑚𝑎𝑥= 220.000 mm
𝜌_𝑚𝑖𝑛=1.4/𝑓𝑦
= 0.003373

**SHORT DIRECTION

AT MIDSPAN

𝑀_𝑢= 6.053
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.9531892
𝜌_𝑎= 0.002363 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 9.438
𝑏=
DESIGN OF SLABS
 𝑀_𝑢=
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 1.4861725
𝜌_𝑎= 0.003747 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE

𝑀_𝑢= 2.018
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.3177297
𝜌_𝑎= 0.000773 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

**LONG DIRECTION

AT MIDSPAN

𝑀_𝑢= 2.555
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.5475563
𝜌_𝑎= 0.001341 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 3.925
𝑏= 1000.00
𝑑=
DESIGN OF SLABS
 𝑏=
𝑑= 72.000

𝑅_𝑢= 0.8411938
𝜌_𝑎= 0.002078 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE

𝑀_𝑢= 0.852
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.1825188
𝜌_𝑎= 0.000442 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

COLUMN STRIP

𝑆_1=1.5(Middle strip)

**SHORT DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

DESIGN OF SLABS
 **LONG DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

F. DEFLECTION
𝛿_𝑎𝑙𝑙=𝐿/48
0

Short Direction = 7.692 mm

Long Direction = 11.858 mm

**DEADLOAD
∆𝐷= 1/16
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:
M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 1.041 mm

Long Direction:

∆𝐷= 1.051 mm

**LIVELOAD
∆𝐷= 3/32
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:

DESIGN OF SLABS
 M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 0.867 mm

Long Direction:

∆𝐷= 0.863 mm

**DUE TO TIME - DEPENDENT INCREMENT

Short Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 1.562

𝛿_𝑇= 1.562+ 0.867

𝛿_𝑇= 2.429 mm < 7.692
Thus, SAFE!

Long Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 1.576
𝛿_𝑇= 1.576+ 0.863
𝛿_𝑇= 2.439 mm < 11.858
Thus, SAFE!

G. SLAB REACTION

**Interpolation of Coefficient

Wa
Ratio Value
0.6 0.89
0.649 0.851096
0.65 0.85

Wb
Ratio Value
0.6 0.19

DESIGN OF SLABS
 0.649 0.151096
0.65 0.15

**Deadload
𝑊_𝑎 𝐷𝐿= 𝑊_𝑎 (𝐷𝐿)(𝐿_𝑎)
(𝐿_𝑏)
𝑊_𝑎 75.943 KN
𝐷𝐿=

𝑊_𝑏 𝐷𝐿= 𝑊_𝑏 (𝐷𝐿)(𝐿_𝑎)

(𝐿_𝑏)
𝑊_𝑏 13.482 KN
𝐷𝐿=
**Live Load
𝑊_𝑎 𝐿𝐿= 𝑊_𝑎 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)
𝑊_𝑎 33.983 KN
𝐿𝐿=

𝑊_𝑏 𝐿𝐿= 𝑊_𝑏 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)

𝑊_𝑏 6.033 KN
𝐿𝐿=
H. Reaction on Beam

**Long Direction
𝑊_𝑎 𝐷𝐿=(𝑊_𝑎
𝐷𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 6.671 KN/m

𝐷𝐿=
𝑊_𝑎 𝐿𝐿=(𝑊_𝑎
𝐿𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 2.985 KN/m

𝐿𝐿=
**Short Direction
𝑊_𝐵 𝐷𝐿=(𝑊_𝑏
𝐷𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 1.826 KN/m

𝐷𝐿=
𝑊_𝑏 𝐿𝐿=(𝑊_𝑏
𝐿𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 0.817 KN/m

𝐿𝐿=

DESIGN OF SLABS
SLAB 2:

A. LOADINGS

DL = 4.246 KPa
LL = 1.900 KPa

**Factored Load

1.2 DL = 5.095
1.6 LL = 3.040

𝑊_𝑢=1.2 𝐷𝐿+1.6𝐿𝐿
𝑊_𝑢= 8.135 Kpa

B. CALCULATE FACTORED MOMENT

𝐿_𝑎=4𝑚 −2(𝑡_𝑓/2)

𝐿_𝑎= 3.692 m
𝐿_𝑏=6𝑚 −2(𝑡_𝑓/2)

𝐿_𝑏= 5.692 m
𝐿_𝑎/
𝐿_𝑏 = 0.649

**Interpolation of Coefficient (Case 9)

Deadload Positive Moment

Ca
Ratio Value
0.6 0.036
0.649 0.034055
0.65 0.034

Cb
Ratio Value
0.6 0.004
0.649 0.004973
0.65 0.005

Live load Positive Moment

Ca
Ratio Value
0.6 0.059

DESIGN OF SLABS
 0.649 0.054137
0.65 0.054

Cb
Ratio Value
0.6 0.007
0.649 0.007000
0.65 0.007

Negative Moment at Continuous Edge

Ca
Ratio Value
0.6 0.085
0.649 0.083055
0.65 0.083

Cb
Ratio Value
0.6 0.006
0.649 0.007945
0.65 0.008

**Positive Moment

Short Direction
𝑀_𝑎 𝐷𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 2.365
𝐷𝐿=
𝑀_𝑎 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 2.243
𝐿𝐿=
𝑀_𝑎 4.608
=
Long Direction
𝑀_𝑏 𝐷𝐿=𝐶_𝑏 𝑊_𝑢
〖𝐿 _𝑏 〗 ^2
𝑀_𝑏 0.821
𝐷𝐿=
𝑀_𝑏 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑏 0.689
𝐿𝐿=
𝑀_𝑏 1.510
=
**Negative Moment at Continuous Edge

𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎=

DESIGN OF SLABS
 𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎= 9.210

𝑀_𝑏=𝐶_𝑏 𝑊_𝑢 〖𝐿 _𝑏 〗
^2
𝑀_𝑏= 2.094
**Negative Moment at Discontinuous Edge

𝑀_𝑎=1/3(𝑃𝑜𝑠𝑖𝑡𝑖𝑣𝑒 𝑀𝑜𝑚𝑒𝑛𝑡)

𝑀_𝑎= 1.536

𝑀_𝑏= 0.503

C. Examine the Depth of Slab

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑑=√(𝑀𝑢/
(∅𝑏𝑅𝑢))

**Where:

𝑅_𝑢=𝑓^′ 𝑐𝜔(1−0.59𝜔)
𝜔=(𝜌_𝑚𝑎𝑥 𝑓𝑦)/(𝑓^
′ 𝑐)

𝜌_𝑚𝑎𝑥=0.75((0.85𝑓^′ 𝑐𝛽_1
(600))/(𝑓𝑦(600+𝑓𝑦)))

𝜌_𝑚𝑎𝑥= 0.015977

𝜔= 0.3203202
𝑅_𝑢= 5.378
𝑀_𝑢= 9.210× 〖 1 (Maximum Moment)
∅= 0〗^
0.96
𝑏= 1000 mm (1m Strip)

𝑑= 43.623 mm

D. Effective Depth of Slab

𝑑=ℎ −20 −12/2

𝑑= 84.000 mm

Therefore, use:
𝑑= 84.000 mm

DESIGN OF SLABS
E. CALCULATE AREA OF STEEL AND SPACING

MIDDLE STRIP

𝜌_𝑎=𝐴𝑠/𝑏𝑑

𝜌_𝑎=(0.85𝑓^′ 𝑐)/𝑓𝑦 [1−√(1−2𝑅𝑢/(0.85𝑓^′

𝑐)) ]

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑆_1=(1000
𝜋𝐷^2)/(4𝐴_𝑆 ) ;D = 12 mm

𝑆_𝑚𝑎𝑥= 220.000 mm
𝜌_𝑚𝑖𝑛=1.4/𝑓𝑦
= 0.003373

**SHORT DIRECTION

AT MIDSPAN

𝑀_𝑢= 4.608
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.7257016
𝜌_𝑎= 0.001786 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 9.210
𝑏=
DESIGN OF SLABS
 𝑀_𝑢=
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 1.4502916
𝜌_𝑎= 0.003652 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE

𝑀_𝑢= 1.536
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.2419005
𝜌_𝑎= 0.000587 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

**LONG DIRECTION

AT MIDSPAN

𝑀_𝑢= 1.510
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.3237133
𝜌_𝑎= 0.000787 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 2.094
𝑏= 1000.00
𝑑=
DESIGN OF SLABS
 𝑏=
𝑑= 72.000

𝑅_𝑢= 0.4488431
𝜌_𝑎= 0.001096 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE

𝑀_𝑢= 0.503
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.1079044
𝜌_𝑎= 0.000261 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

COLUMN STRIP

𝑆_1=1.5(Middle strip)

**SHORT DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

DESIGN OF SLABS
 **LONG DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

F. DEFLECTION
𝛿_𝑎𝑙𝑙=𝐿/48
0

Short Direction = 7.692 mm

Long Direction = 11.858 mm

**DEADLOAD
∆𝐷= 1/16
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:
M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 0.708 mm

Long Direction:

∆𝐷= 0.584 mm

**LIVELOAD
∆𝐷= 3/32
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:

DESIGN OF SLABS
 M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 0.755 mm

Long Direction:

∆𝐷= 0.552 mm

**DUE TO TIME - DEPENDENT INCREMENT

Short Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 1.062

𝛿_𝑇= 1.062+ 0.755

𝛿_𝑇= 1.817 mm < 7.692
Thus, SAFE!

Long Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 0.876
𝛿_𝑇= 0.876+ 0.552
𝛿_𝑇= 1.428 mm < 11.858
Thus, SAFE!

G. SLAB REACTION

**Interpolation of Coefficient

Wa
Ratio Value
0.6 0.94
0.649 0.920548
0.65 0.92

Wb
Ratio Value
0.6 0.06

DESIGN OF SLABS
 0.649 0.079452
0.65 0.08

**Deadload
𝑊_𝑎 𝐷𝐿= 𝑊_𝑎 (𝐷𝐿)(𝐿_𝑎)
(𝐿_𝑏)
𝑊_𝑎 82.140 KN
𝐷𝐿=

𝑊_𝑏 𝐷𝐿= 𝑊_𝑏 (𝐷𝐿)(𝐿_𝑎)

(𝐿_𝑏)
𝑊_𝑏 7.089 KN
𝐷𝐿=
**Live Load
𝑊_𝑎 𝐿𝐿= 𝑊_𝑎 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)
𝑊_𝑎 36.756 KN
𝐿𝐿=

𝑊_𝑏 𝐿𝐿= 𝑊_𝑏 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)

𝑊_𝑏 3.172 KN
𝐿𝐿=
H. Reaction on Beam

**Long Direction
𝑊_𝑎 𝐷𝐿=(𝑊_𝑎
𝐷𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 7.215 KN/m

𝐷𝐿=
𝑊_𝑎 𝐿𝐿=(𝑊_𝑎
𝐿𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 3.229 KN/m

𝐿𝐿=
**Short Direction
𝑊_𝐵 𝐷𝐿=(𝑊_𝑏
𝐷𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 0.960 KN/m

𝐷𝐿=
𝑊_𝑏 𝐿𝐿=(𝑊_𝑏
𝐿𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 0.430 KN/m

𝐿𝐿=

DESIGN OF SLABS
SLAB 3:

A. LOADINGS

DL = 4.296 KPa
LL = 2.400 KPa

**Factored Load

1.2 DL = 5.155
1.6 LL = 3.840

𝑊_𝑢=1.2 𝐷𝐿+1.6𝐿𝐿
𝑊_𝑢= 8.995 Kpa

B. CALCULATE FACTORED MOMENT

𝐿_𝑎=4𝑚 −2(𝑡_𝑓/2)

𝐿_𝑎= 3.692 m
𝐿_𝑏=6𝑚 −2(𝑡_𝑓/2)

𝐿_𝑏= 5.692 m
𝐿_𝑎/
𝐿_𝑏 = 0.649

**Interpolation of Coefficient (Case 9)

Deadload Positive Moment

Ca
Ratio Value
0.6 0.036
0.649 0.034055
0.65 0.034

Cb
Ratio Value
0.6 0.004
0.649 0.004973
0.65 0.005

Live load Positive Moment

Ca
Ratio Value
0.6 0.059

DESIGN OF SLABS
 0.649 0.054137
0.65 0.054

Cb
Ratio Value
0.6 0.007
0.649 0.007000
0.65 0.007

Negative Moment at Continuous Edge

Ca
Ratio Value
0.6 0.085
0.649 0.083055
0.65 0.083

Cb
Ratio Value
0.6 0.006
0.649 0.007945
0.65 0.008

**Positive Moment

Short Direction
𝑀_𝑎 𝐷𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 2.393
𝐷𝐿=
𝑀_𝑎 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 2.834
𝐿𝐿=
𝑀_𝑎 5.227
=
Long Direction
𝑀_𝑏 𝐷𝐿=𝐶_𝑏 𝑊_𝑢
〖𝐿 _𝑏 〗 ^2
𝑀_𝑏 0.831
𝐷𝐿=
𝑀_𝑏 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑏 0.871
𝐿𝐿=
𝑀_𝑏 1.701
=
**Negative Moment at Continuous Edge

𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎=

DESIGN OF SLABS
 𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎= 10.184

𝑀_𝑏=𝐶_𝑏 𝑊_𝑢 〖𝐿 _𝑏 〗
^2
𝑀_𝑏= 2.315
**Negative Moment at Discontinuous Edge

𝑀_𝑎=1/3(𝑃𝑜𝑠𝑖𝑡𝑖𝑣𝑒 𝑀𝑜𝑚𝑒𝑛𝑡)

𝑀_𝑎= 1.742

𝑀_𝑏= 0.567

C. Examine the Depth of Slab

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑑=√(𝑀𝑢/
(∅𝑏𝑅𝑢))

**Where:

𝑅_𝑢=𝑓^′ 𝑐𝜔(1−0.59𝜔)
𝜔=(𝜌_𝑚𝑎𝑥 𝑓𝑦)/(𝑓^
′ 𝑐)

𝜌_𝑚𝑎𝑥=0.75((0.85𝑓^′ 𝑐𝛽_1
(600))/(𝑓𝑦(600+𝑓𝑦)))

𝜌_𝑚𝑎𝑥= 0.015977

𝜔= 0.3203202
𝑅_𝑢= 5.378
𝑀_𝑢= 10.184× 〖 1 (Maximum Moment)
∅= 0〗^
0.96
𝑏= 1000 mm (1m Strip)

𝑑= 45.871 mm

D. Effective Depth of Slab

𝑑=ℎ −20 −12/2

𝑑= 84.000 mm

Therefore, use:
𝑑= 84.000 mm

DESIGN OF SLABS
E. CALCULATE AREA OF STEEL AND SPACING

MIDDLE STRIP

𝜌_𝑎=𝐴𝑠/𝑏𝑑

𝜌_𝑎=(0.85𝑓^′ 𝑐)/𝑓𝑦 [1−√(1−2𝑅𝑢/(0.85𝑓^′

𝑐)) ]

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑆_1=(1000
𝜋𝐷^2)/(4𝐴_𝑆 ) ;D = 12 mm

𝑆_𝑚𝑎𝑥= 220.000 mm
𝜌_𝑚𝑖𝑛=1.4/𝑓𝑦
= 0.003373

**SHORT DIRECTION

AT MIDSPAN

𝑀_𝑢= 5.227
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.8230497
𝜌_𝑎= 0.002032 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 10.184
𝑏=
DESIGN OF SLABS
 𝑀_𝑢=
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 1.603607
𝜌_𝑎= 0.004058 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE

𝑀_𝑢= 1.742
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.2743499
𝜌_𝑎= 0.000666 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

**LONG DIRECTION

AT MIDSPAN

𝑀_𝑢= 1.701
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.3646727
𝜌_𝑎= 0.000888 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 2.315
𝑏= 1000.00
𝑑=
DESIGN OF SLABS
 𝑏=
𝑑= 72.000

𝑅_𝑢= 0.4962919
𝜌_𝑎= 0.001213 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE

𝑀_𝑢= 0.567
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.1215576
𝜌_𝑎= 0.000294 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

COLUMN STRIP

𝑆_1=1.5(Middle strip)

**SHORT DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

DESIGN OF SLABS
 **LONG DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

F. DEFLECTION
𝛿_𝑎𝑙𝑙=𝐿/48
0

Short Direction = 7.692 mm

Long Direction = 11.858 mm

**DEADLOAD
∆𝐷= 1/16
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:
M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 0.716 mm

Long Direction:

∆𝐷= 0.591 mm

**LIVELOAD
∆𝐷= 3/32
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:

DESIGN OF SLABS
 M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 0.954 mm

Long Direction:

∆𝐷= 0.697 mm

**DUE TO TIME - DEPENDENT INCREMENT

Short Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 1.074

𝛿_𝑇= 1.074+ 0.954

𝛿_𝑇= 2.029 mm < 7.692
Thus, SAFE!

Long Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 0.886
𝛿_𝑇= 0.886+ 0.697
𝛿_𝑇= 1.583 mm < 11.858
Thus, SAFE!

G. SLAB REACTION

**Interpolation of Coefficient

Wa
Ratio Value
0.6 0.94
0.649 0.920548
0.65 0.92

Wb
Ratio Value
0.6 0.06

DESIGN OF SLABS
 0.649 0.079452
0.65 0.08

**Deadload
𝑊_𝑎 𝐷𝐿= 𝑊_𝑎 (𝐷𝐿)(𝐿_𝑎)
(𝐿_𝑏)
𝑊_𝑎 83.107 KN
𝐷𝐿=

𝑊_𝑏 𝐷𝐿= 𝑊_𝑏 (𝐷𝐿)(𝐿_𝑎)

(𝐿_𝑏)
𝑊_𝑏 7.173 KN
𝐷𝐿=
**Live Load
𝑊_𝑎 𝐿𝐿= 𝑊_𝑎 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)
𝑊_𝑎 46.428 KN
𝐿𝐿=

𝑊_𝑏 𝐿𝐿= 𝑊_𝑏 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)

𝑊_𝑏 4.007 KN
𝐿𝐿=
H. Reaction on Beam

**Short Direction
𝑊_𝑎 𝐷𝐿=(𝑊_𝑎
𝐷𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 7.300 KN/m

𝐷𝐿=
𝑊_𝑎 𝐿𝐿=(𝑊_𝑎
𝐿𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 4.078 KN/m

𝐿𝐿=
**Long Direction
𝑊_𝐵 𝐷𝐿=(𝑊_𝑏
𝐷𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 0.971 KN/m

𝐷𝐿=
𝑊_𝑏 𝐿𝐿=(𝑊_𝑏
𝐿𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 0.543 KN/m

𝐿𝐿=

DESIGN OF SLABS
SLAB 4:

A. LOADINGS

DL = 4.246 KPa
LL = 3.800 KPa

**Factored Load

1.2 DL = 5.095
1.6 LL = 6.080

𝑊_𝑢=1.2 𝐷𝐿+1.6𝐿𝐿
𝑊_𝑢= 11.175 Kpa

B. CALCULATE FACTORED MOMENT

𝐿_𝑎=4𝑚 −2(𝑡_𝑓/2)

𝐿_𝑎= 3.692 m
𝐿_𝑏=6𝑚 −2(𝑡_𝑓/2)

𝐿_𝑏= 5.692 m
𝐿_𝑎/
𝐿_𝑏 = 0.649

**Interpolation of Coefficient (Case 9)

Deadload Positive Moment

Ca
Ratio Value
0.6 0.036
0.649 0.034055
0.65 0.034

Cb
Ratio Value
0.6 0.004
0.649 0.004973
0.65 0.005

Live load Positive Moment

Ca
Ratio Value
0.6 0.059

DESIGN OF SLABS
 0.649 0.054137
0.65 0.054

Cb
Ratio Value
0.6 0.007
0.649 0.007000
0.65 0.007

Negative Moment at Continuous Edge

Ca
Ratio Value
0.6 0.085
0.649 0.083055
0.65 0.083

Cb
Ratio Value
0.6 0.006
0.649 0.007945
0.65 0.008

**Positive Moment

Short Direction
𝑀_𝑎 𝐷𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 2.365
𝐷𝐿=
𝑀_𝑎 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 4.487
𝐿𝐿=
𝑀_𝑎 6.852
=
Long Direction
𝑀_𝑏 𝐷𝐿=𝐶_𝑏 𝑊_𝑢
〖𝐿 _𝑏 〗 ^2
𝑀_𝑏 0.821
𝐷𝐿=
𝑀_𝑏 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑏 1.379
𝐿𝐿=
𝑀_𝑏 2.200
=
**Negative Moment at Continuous Edge

𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎=

DESIGN OF SLABS
 𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎= 12.652

𝑀_𝑏=𝐶_𝑏 𝑊_𝑢 〖𝐿 _𝑏 〗
^2
𝑀_𝑏= 2.877
**Negative Moment at Discontinuous Edge

𝑀_𝑎=1/3(𝑃𝑜𝑠𝑖𝑡𝑖𝑣𝑒 𝑀𝑜𝑚𝑒𝑛𝑡)

𝑀_𝑎= 2.284

𝑀_𝑏= 0.733

C. Examine the Depth of Slab

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑑=√(𝑀𝑢/
(∅𝑏𝑅𝑢))

**Where:

𝑅_𝑢=𝑓^′ 𝑐𝜔(1−0.59𝜔)
𝜔=(𝜌_𝑚𝑎𝑥 𝑓𝑦)/(𝑓^
′ 𝑐)

𝜌_𝑚𝑎𝑥=0.75((0.85𝑓^′ 𝑐𝛽_1
(600))/(𝑓𝑦(600+𝑓𝑦)))

𝜌_𝑚𝑎𝑥= 0.015977

𝜔= 0.3203202
𝑅_𝑢= 5.378
𝑀_𝑢= 12.652× 〖 1 (Maximum Moment)
∅= 0〗^
0.96
𝑏= 1000 mm (1m Strip)

𝑑= 51.128 mm

D. Effective Depth of Slab

𝑑=ℎ −20 −12/2

𝑑= 84.000 mm

Therefore, use:
𝑑= 84.000 mm

DESIGN OF SLABS
E. CALCULATE AREA OF STEEL AND SPACING

MIDDLE STRIP

𝜌_𝑎=𝐴𝑠/𝑏𝑑

𝜌_𝑎=(0.85𝑓^′ 𝑐)/𝑓𝑦 [1−√(1−2𝑅𝑢/(0.85𝑓^′

𝑐)) ]

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑆_1=(1000
𝜋𝐷^2)/(4𝐴_𝑆 ) ;D = 12 mm

𝑆_𝑚𝑎𝑥= 220.000 mm
𝜌_𝑚𝑖𝑛=1.4/𝑓𝑦
= 0.003373

**SHORT DIRECTION

AT MIDSPAN

𝑀_𝑢= 6.852
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 1.0789582
𝜌_𝑎= 0.002685 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 12.652
𝑏=
DESIGN OF SLABS
 𝑀_𝑢=
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 1.9922435
𝜌_𝑎= 0.005108 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE

𝑀_𝑢= 2.284
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.3596527
𝜌_𝑎= 0.000876 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

**LONG DIRECTION

AT MIDSPAN

𝑀_𝑢= 2.200
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.4714859
𝜌_𝑎= 0.001152 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 2.877
𝑏= 1000.00
𝑑=
DESIGN OF SLABS
 𝑏=
𝑑= 72.000

𝑅_𝑢= 0.616569
𝜌_𝑎= 0.001513 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE

𝑀_𝑢= 0.733
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.157162
𝜌_𝑎= 0.000380 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

COLUMN STRIP

𝑆_1=1.5(Middle strip)

**SHORT DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

DESIGN OF SLABS
 **LONG DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

F. DEFLECTION
𝛿_𝑎𝑙𝑙=𝐿/48
0

Short Direction = 7.692 mm

Long Direction = 11.858 mm

**DEADLOAD
∆𝐷= 1/16
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:
M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 0.708 mm

Long Direction:

∆𝐷= 0.584 mm

**LIVELOAD
∆𝐷= 3/32
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:

DESIGN OF SLABS
 M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 1.511 mm

Long Direction:

∆𝐷= 1.104 mm

**DUE TO TIME - DEPENDENT INCREMENT

Short Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 1.062

𝛿_𝑇= 1.062+ 1.511

𝛿_𝑇= 2.573 mm < 7.692
Thus, SAFE!

Long Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 0.876
𝛿_𝑇= 0.876+ 1.104
𝛿_𝑇= 1.980 mm < 11.858
Thus, SAFE!

G. SLAB REACTION

**Interpolation of Coefficient

Wa
Ratio Value
0.6 0.94
0.649 0.920548
0.65 0.92

Wb
Ratio Value
0.6 0.06

DESIGN OF SLABS
 0.649 0.079452
0.65 0.08

**Deadload
𝑊_𝑎 𝐷𝐿= 𝑊_𝑎 (𝐷𝐿)(𝐿_𝑎)
(𝐿_𝑏)
𝑊_𝑎 82.140 KN
𝐷𝐿=

𝑊_𝑏 𝐷𝐿= 𝑊_𝑏 (𝐷𝐿)(𝐿_𝑎)

(𝐿_𝑏)
𝑊_𝑏 7.089 KN
𝐷𝐿=
**Live Load
𝑊_𝑎 𝐿𝐿= 𝑊_𝑎 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)
𝑊_𝑎 73.512 KN
𝐿𝐿=

𝑊_𝑏 𝐿𝐿= 𝑊_𝑏 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)

𝑊_𝑏 6.345 KN
𝐿𝐿=
H. Reaction on Beam

**Long Direction
𝑊_𝑎 𝐷𝐿=(𝑊_𝑎
𝐷𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 7.215 KN/m

𝐷𝐿=
𝑊_𝑎 𝐿𝐿=(𝑊_𝑎
𝐿𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 6.457 KN/m

𝐿𝐿=
**Short Direction
𝑊_𝐵 𝐷𝐿=(𝑊_𝑏
𝐷𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 0.960 KN/m

𝐷𝐿=
𝑊_𝑏 𝐿𝐿=(𝑊_𝑏
𝐿𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 0.859 KN/m

𝐿𝐿=

DESIGN OF SLABS
SLAB 5:

A. LOADINGS

DL = 4.246 KPa
LL = 3.800 KPa

**Factored Load

1.2 DL = 5.095
1.6 LL = 6.080

𝑊_𝑢=1.2 𝐷𝐿+1.6𝐿𝐿
𝑊_𝑢= 11.175 Kpa

B. CALCULATE FACTORED MOMENT

𝐿_𝑎=3𝑚 −2(𝑡_𝑓/2)

𝐿_𝑎= 2.692 m
𝐿_𝑏=4𝑚 −2(𝑡_𝑓/2)

𝐿_𝑏= 3.692 m
𝐿_𝑎/
𝐿_𝑏 = 0.729

**Interpolation of Coefficient (Case 9)

Deadload Positive Moment

Ca
Ratio Value
0.75 0.031
0.729 0.031834
0.7 0.033

Cb
Ratio Value
0.75 0.007
0.729 0.006583
0.7 0.006

Live load Positive Moment

Ca
Ratio Value
0.75 0.046

DESIGN OF SLABS
 0.729 0.047668
0.7 0.05

Cb
Ratio Value
0.75 0.013
0.729 0.012166
0.7 0.011

Negative Moment at Continuous Edge

Ca
Ratio Value
0.75 0.078
0.729 0.079251
0.7 0.081

Cb
Ratio Value
0.75 0.014
0.729 0.012749
0.7 0.011

**Positive Moment

Short Direction
𝑀_𝑎 𝐷𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 1.175
𝐷𝐿=
𝑀_𝑎 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 2.100
𝐿𝐿=
𝑀_𝑎 3.276
=
Long Direction
𝑀_𝑏 𝐷𝐿=𝐶_𝑏 𝑊_𝑢
〖𝐿 _𝑏 〗 ^2
𝑀_𝑏 0.457
𝐷𝐿=
𝑀_𝑏 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑏 1.008
𝐿𝐿=
𝑀_𝑏 1.465
=
**Negative Moment at Continuous Edge

𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎=

DESIGN OF SLABS
 𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎= 6.418

𝑀_𝑏=𝐶_𝑏 𝑊_𝑢 〖𝐿 _𝑏 〗
^2
𝑀_𝑏= 1.942
**Negative Moment at Discontinuous Edge

𝑀_𝑎=1/3(𝑃𝑜𝑠𝑖𝑡𝑖𝑣𝑒 𝑀𝑜𝑚𝑒𝑛𝑡)

𝑀_𝑎= 1.092

𝑀_𝑏= 0.488

C. Examine the Depth of Slab

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑑=√(𝑀𝑢/
(∅𝑏𝑅𝑢))

**Where:

𝑅_𝑢=𝑓^′ 𝑐𝜔(1−0.59𝜔)
𝜔=(𝜌_𝑚𝑎𝑥 𝑓𝑦)/(𝑓^
′ 𝑐)

𝜌_𝑚𝑎𝑥=0.75((0.85𝑓^′ 𝑐𝛽_1
(600))/(𝑓𝑦(600+𝑓𝑦)))

𝜌_𝑚𝑎𝑥= 0.015977

𝜔= 0.3203202
𝑅_𝑢= 5.378
𝑀_𝑢= 6.418× 〖 1 (Maximum Moment)
∅= 0〗^
0.96
𝑏= 1000 mm (1m Strip)

𝑑= 36.416 mm

D. Effective Depth of Slab

𝑑=ℎ −20 −12/2

𝑑= 84.000 mm

Therefore, use:
𝑑= 84.000 mm

DESIGN OF SLABS
E. CALCULATE AREA OF STEEL AND SPACING

MIDDLE STRIP

𝜌_𝑎=𝐴𝑠/𝑏𝑑

𝜌_𝑎=(0.85𝑓^′ 𝑐)/𝑓𝑦 [1−√(1−2𝑅𝑢/(0.85𝑓^′

𝑐)) ]

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑆_1=(1000
𝜋𝐷^2)/(4𝐴_𝑆 ) ;D = 12 mm

𝑆_𝑚𝑎𝑥= 220.000 mm
𝜌_𝑚𝑖𝑛=1.4/𝑓𝑦
= 0.003373

**SHORT DIRECTION

AT MIDSPAN

𝑀_𝑢= 3.276
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.5158371
𝜌_𝑎= 0.001262 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 6.418
𝑏=
DESIGN OF SLABS
 𝑀_𝑢=
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 1.0106738
𝜌_𝑎= 0.002510 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE

𝑀_𝑢= 1.092
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.1719457
𝜌_𝑎= 0.000416 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

**LONG DIRECTION

AT MIDSPAN

𝑀_𝑢= 1.465
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.3140946
𝜌_𝑎= 0.000764 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 1.942
𝑏= 1000.00
𝑑=
DESIGN OF SLABS
 𝑏=
𝑑= 72.000

𝑅_𝑢= 0.4162318
𝜌_𝑎= 0.001015 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE

𝑀_𝑢= 0.488
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.1046982
𝜌_𝑎= 0.000253 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

COLUMN STRIP

𝑆_1=1.5(Middle strip)

**SHORT DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

DESIGN OF SLABS
 **LONG DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

F. DEFLECTION
𝛿_𝑎𝑙𝑙=𝐿/48
0

Short Direction = 5.608 mm

Long Direction = 7.692 mm

**DEADLOAD
∆𝐷= 1/16
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:
M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 0.187 mm

Long Direction:

∆𝐷= 0.137 mm

**LIVELOAD
∆𝐷= 3/32
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:

DESIGN OF SLABS
 M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 0.376 mm

Long Direction:

∆𝐷= 0.340 mm

**DUE TO TIME - DEPENDENT INCREMENT

Short Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 0.281

𝛿_𝑇= 0.281+ 0.376

𝛿_𝑇= 0.657 mm < 5.608
Thus, SAFE!

Long Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 0.205
𝛿_𝑇= 0.205+ 0.340
𝛿_𝑇= 0.545 mm < 7.692
Thus, SAFE!

G. SLAB REACTION

**Interpolation of Coefficient

Wa
Ratio Value
0.75 0.86
0.729 0.872514
0.7 0.89

Wb
Ratio Value
0.75 0.14

DESIGN OF SLABS
 0.729 0.127486
0.7 0.11

**Deadload
𝑊_𝑎 𝐷𝐿= 𝑊_𝑎 (𝐷𝐿)(𝐿_𝑎)
(𝐿_𝑏)
𝑊_𝑎 36.820 KN
𝐷𝐿=

𝑊_𝑏 𝐷𝐿= 𝑊_𝑏 (𝐷𝐿)(𝐿_𝑎)

(𝐿_𝑏)
𝑊_𝑏 5.380 KN
𝐷𝐿=
**Live Load
𝑊_𝑏 𝐿𝐿= 𝑊_𝑎 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)
𝑊_𝑎 32.953 KN
𝐿𝐿=

𝑊_𝑏 𝐿𝐿= 𝑊_𝑏 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)

𝑊_𝑏 4.815 KN
𝐿𝐿=
H. Reaction on Beam

**Long Direction
𝑊_𝑎 𝐷𝐿=(𝑊_𝑎
𝐷𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 4.987 KN/m

𝐷𝐿=
𝑊_𝑎 𝐿𝐿=(𝑊_𝑎
𝐿𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 4.463 KN/m

𝐿𝐿=
**Short Direction
𝑊_𝐵 𝐷𝐿=(𝑊_𝑏
𝐷𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 0.999 KN/m

𝐷𝐿=
𝑊_𝑏 𝐿𝐿=(𝑊_𝑏
𝐿𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 0.894 KN/m

𝐿𝐿=

DESIGN OF SLABS
SLAB 6:

A. LOADINGS

DL = 4.246 KPa
LL = 3.800 KPa

**Factored Load

1.2 DL = 5.095
1.6 LL = 6.080

𝑊_𝑢=1.2 𝐷𝐿+1.6𝐿𝐿
𝑊_𝑢= 11.175 Kpa

B. CALCULATE FACTORED MOMENT

𝐿_𝑎=3𝑚 −2(𝑡_𝑓/2)

𝐿_𝑎= 2.692 m
𝐿_𝑏=4𝑚 −2(𝑡_𝑓/2)

𝐿_𝑏= 3.692 m
𝐿_𝑎/
𝐿_𝑏 = 0.729

**Interpolation of Coefficient (Case 2)

Deadload Positive Moment

Ca
Ratio Value
0.75 0.028
0.729 0.028834
0.7 0.03

Cb
Ratio Value
0.75 0.009
0.729 0.008166
0.7 0.007

Live load Positive Moment

Ca
Ratio Value
0.75 0.045

DESIGN OF SLABS
 0.729 0.046668
0.7 0.049

Cb
Ratio Value
0.75 0.014
0.729 0.013166
0.7 0.012

Negative Moment at Continuous Edge

Ca
Ratio Value
0.75 0.069
0.729 0.071086
0.7 0.074

Cb
Ratio Value
0.75 0.022
0.729 0.019914
0.7 0.017

**Positive Moment

Short Direction
𝑀_𝑎 𝐷𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 1.065
𝐷𝐿=
𝑀_𝑎 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑎 2.056
𝐿𝐿=
𝑀_𝑎 3.121
=
Long Direction
𝑀_𝑏 𝐷𝐿=𝐶_𝑏 𝑊_𝑢
〖𝐿 _𝑏 〗 ^2
𝑀_𝑏 0.567
𝐷𝐿=
𝑀_𝑏 𝐿𝐿=𝐶_𝑎 𝑊_𝑢
〖𝐿 _𝑎 〗 ^2
𝑀_𝑏 1.091
𝐿𝐿=
𝑀_𝑏 1.658
=
**Negative Moment at Continuous Edge

𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎=

DESIGN OF SLABS
 𝑀_𝑎=𝐶_𝑎 𝑊_𝑢 〖𝐿 _𝑎 〗
^2
𝑀_𝑎= 5.757

𝑀_𝑏=𝐶_𝑏 𝑊_𝑢 〖𝐿 _𝑏 〗
^2
𝑀_𝑏= 3.034

C. Examine the Depth of Slab

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)
𝑑=√(𝑀𝑢/
(∅𝑏𝑅𝑢))

**Where:

𝑅_𝑢=𝑓^′ 𝑐𝜔(1−0.59𝜔)
𝜔=(𝜌_𝑚𝑎𝑥 𝑓𝑦)/(𝑓^
′ 𝑐)

𝜌_𝑚𝑎𝑥=0.75((0.85𝑓^′ 𝑐𝛽_1
(600))/(𝑓𝑦(600+𝑓𝑦)))

𝜌_𝑚𝑎𝑥= 0.015977

𝜔= 0.3203202
𝑅_𝑢= 5.378
𝑀_𝑢= 5.757× 〖 1 (Maximum Moment)
∅= 0〗^
0.96
𝑏= 1000 mm (1m Strip)

𝑑= 34.489 mm

D. Effective Depth of Slab

𝑑=ℎ −20 −12/2

𝑑= 84.000 mm

Therefore, use:
𝑑= 84.000 mm

E. CALCULATE AREA OF STEEL AND SPACING

MIDDLE STRIP

𝜌_𝑎=𝐴𝑠/𝑏𝑑

𝜌_𝑎=(0.85𝑓^′ 𝑐)/𝑓𝑦 [1−√(1−2𝑅𝑢/(0.85𝑓^′

𝑐)) ]
DESIGN OF SLABS
 𝜌_𝑎=(0.85𝑓^′ 𝑐)/𝑓𝑦 [1−√(1−2𝑅𝑢/(0.85𝑓^′
𝑐)) ]

𝑅𝑢=
𝑀𝑢/(∅𝑏𝑑^2
)

𝑆_1=(1000
𝜋𝐷^2)/(4𝐴_𝑆 ) ;D = 12 mm

𝑆_𝑚𝑎𝑥= 220.000 mm
𝜌_𝑚𝑖𝑛=1.4/𝑓𝑦
= 0.003373

**SHORT DIRECTION

AT MIDSPAN

𝑀_𝑢= 3.121
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.4914554
𝜌_𝑎= 0.001201 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 5.757
𝑏= 1000.00
𝑑= 84.000

𝑅_𝑢= 0.9065378
𝜌_𝑎= 0.002244 Use: 0.003373

𝐴_𝑠= 283.37349

𝑆_1= 399.110 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

DESIGN OF SLABS
**LONG DIRECTION

AT MIDSPAN

𝑀_𝑢= 1.658
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.3554205
𝜌_𝑎= 0.000865 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE

𝑀_𝑢= 3.034
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= 0.6501875
𝜌_𝑎= 0.001597 Use: 0.003373

𝐴_𝑠= 242.89157

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

COLUMN STRIP

𝑆_1=1.5(Middle strip)

**SHORT DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

DESIGN OF SLABS
 **LONG DIRECTION

AT MIDSPAN
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT CONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

F. DEFLECTION
𝛿_𝑎𝑙𝑙=𝐿/48
0

Short Direction = 5.608 mm

Long Direction = 7.692 mm

**DEADLOAD
∆𝐷= 1/16
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:
M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 0.169 mm

Long Direction:

∆𝐷= 0.170 mm

**LIVELOAD
∆𝐷= 3/32
(𝑀𝐿^2)/(𝐸_𝐶 𝐼_𝐸𝐹𝐹 )

Where:
M = Unfactored Positive Moment
L = Length
𝐸_𝑐=4700√(𝑓^′ 21383.71
𝑐)=

DESIGN OF SLABS
 𝐸_𝑐=4700√(𝑓^′
𝑐)=
𝐼_𝑒𝑓𝑓= 1.11E+08

Short Direction:

∆𝐷= 0.368 mm

Long Direction:

∆𝐷= 0.367 mm

**DUE TO TIME - DEPENDENT INCREMENT

Short Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 0.254

𝛿_𝑇= 0.254+ 0.368

𝛿_𝑇= 0.622 mm < 5.608
Thus, SAFE!

Long Direction
𝛿= ∆𝐷(1/2)(3)

𝛿= 0.255
𝛿_𝑇= 0.255+ 0.367
𝛿_𝑇= 0.622 mm < 7.692
Thus, SAFE!

G. SLAB REACTION

**Interpolation of Coefficient

Wa
Ratio Value
0.75 0.76
0.729 0.780856
0.7 0.81

Wb
Ratio Value
0.75 0.24
0.729 0.219144
0.7 0.19

DESIGN OF SLABS
 **Deadload
𝑊_𝑎 𝐷𝐿= 𝑊_𝑎 (𝐷𝐿)(𝐿_𝑎)
(𝐿_𝑏)
𝑊_𝑎 32.952 KN
𝐷𝐿=

𝑊_𝑏 𝐷𝐿= 𝑊_𝑏 (𝐷𝐿)(𝐿_𝑎)

(𝐿_𝑏)
𝑊_𝑏 9.248 KN
𝐷𝐿=
**Live Load
𝑊_𝑎 𝐿𝐿= 𝑊_𝑎 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)
𝑊_𝑎 29.491 KN
𝐿𝐿=

𝑊_𝑏 𝐿𝐿= 𝑊_𝑏 (𝐿𝐿)(𝐿_𝑎)(𝐿_𝑏)

𝑊_𝑏 8.277 KN
𝐿𝐿=
H. Reaction on Beam

**Long Direction
𝑊_𝑎 𝐷𝐿=(𝑊_𝑎
𝐷𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 4.463 KN/m

𝐷𝐿=
𝑊_𝑎 𝐿𝐿=(𝑊_𝑎
𝐿𝐿)/(2(𝐿_𝑏))

𝑊_𝑎 3.994 KN/m

𝐿𝐿=
**Short Direction
𝑊_𝐵 𝐷𝐿=(𝑊_𝑏
𝐷𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 1.718 KN/m

𝐷𝐿=
𝑊_𝑏 𝐿𝐿=(𝑊_𝑏
𝐿𝐿)/(2(𝐿_𝑎))

𝑊_𝑏 1.537 KN/m

𝐿𝐿=

DESIGN OF SLABS
AT DISCONTINUOUS EDGE

𝑀_𝑢= #REF!
𝑏= 1000.00
𝑑= 72.000

𝑅_𝑢= #REF!
𝜌_𝑎= #REF! Use: 0.003373

𝐴_𝑠= 242.8916

𝑆_1= 465.629 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= #REF! Use: #REF!

Thus, use 12 mm diameter Bars spaced at #REF! mm O.C

AT DISCONTINUOUS EDGE
𝑆_1= 330.000 Use: 220

Thus, use 12 mm diameter Bars spaced at 220 mm O.C