LITHO-DENSITY LOG

INTRODUCTION

The Log
The photo electric factor (PEF) log is a continuous record of the effective photoelectric absorption
index of a formation.

The litho-density log is a new form of the formation density log with added features as Schlumberger’s
Litho-Density Tool (LDT).

Uses

This log is a matrix indicator

This log can’t be used when barite is in the mud as the absorption power of barite is 150 times more
than the others.
Compton Scattering and Photo-Electric Absorption

• After travelling through the rock the gamma rays undergo compton scattering and loose energy, so the
initially sharp peak moves to lower energies.

• Each of the gamma rays undergoes a different number of collisions dependent upon chance, and hence
looses a different amount of energy. Thus the peak is not only moved to lower energies, but is also
dispersed (becomes wider).

• Some of the most scattered gamma rays now have energies close to 0.2 MeV. Once below the 0.2 MeV
threshold, the gamma ray can be completely absorbed by the atoms in the rock. This is called photo-
electric absorption. The result is that gamma rays attaining energies less than 0.2 MeV are eaten away
from the energy distribution.
Compton Scattering and Photo-Electric Absorption

Curve A represents the initial energy spectrum, Curve B represents the energy spectrum after the gamma rays
have traveled a small distance through the rock, and Curve C represents the energy spectrum of the gamma
rays after they have traveled an additional small distance through the rock.
Curve D shows the energies of the gamma rays after they have traveled another small distance through the
rock, where some gamma rays have attained sufficiently low energies that they have been photo-absorbed.
Curve E finally represents the energy distributions of gamma rays as they are detected by the tool.
THEORY

Photo-Electric Absorption Index (Pe)

The specific photo-electric absorption index (Pe) of a material describes the likelihood that a gamma

ray will be photo-electrically absorbed per electron of the atoms that compose the material.

Where ‘Z’ is the average atomic number of the formation.

Volumetric Photo-Electric Absorption Index

The Volumetric photo-electric absorption index (U) of a material describes the likelihood that a gamma

ray will be photo-electrically absorbed per unit volume of the material. It can be written in terms of the

specific photo-electric absorption index as

Mean Atomic Number of the Matrix

 Isolated Pe peaks, this may indicate local deposits of heavy minerals especially those containing
iron, or radioactive placer deposits (uranium and thorium).

 General high value for the Pe curve, may indicate the presence of igneous or metamorphic rocks.

 Lower Pe, the lower the mean atomic number of the formation.

 Thin bands of low Pe may indicate coal.

Formation Fluids
The values of Pe and U for the fluids commonly found in rock are so low compared with the values for
the matrix, that their influence is negligible. The one exception to this is perhaps highly saturated
brines, which may have a significant Pe value.
Tool
These tools have a caesium-137 source emitting gamma rays at 0.662 MeV, a short-spaced and a long-
spaced detector in the same way as the basic formation density tool.

However, the detectors are more efficient, and have the ability to recognize and to count separately
gamma rays which have high energies (hard gamma rays: 0.25 to 0.662 MeV) and gamma rays which
have low energies (soft gamma rays: 0.04 to 0.0 MeV).

The hard gamma rays are those that are undergoing compton scattering.

The soft gamma rays are those that are undergoing photo-electric absorption. This effect can be used to
provide a parameter which is dependent upon the atomic number of the formation, and therefore
immensely useful in lithological recognition.
Tool Operation

• The tool is very similar to the formation density tool.

• It has enhanced detectors, and the distance between the long spacing and the short
spacing detectors has been decreased.

• This decrease has increased the vertical resolution of the tool and improved its overall
counting accuracy.

• The accuracy of the density measurement of the litho-density tool is approximately 0.01 to 0.02
g/cm3.
Log Presentation
 The log is commonly referred to as the photo-electric factor log (PEF). It is shown in tracks 2 and 3 together with
the formation density and neutron curves.
 Scales running from 0 to 10 or 0 to 15 or 0 to 20 barns/electron are most often used. This log is commonly run
combined with the neutron log and a gamma ray log.
 The combination of the formation density log with the neutron log and the PEF log is very powerful in
lithological assessment. The gamma ray log is run to aid depth matching with other logs.
Log Characteristics

Depth of Investigation
The density and PEF measurement from the litho-density tool have a depth of investigation
of 50 to 60 cm.

Vertical Resolution
The density measurement from the litho-density tool has a vertical bed resolution is slightly
better than the formation density tool. The enhanced vertical resolution results from the
shorter distance between the short and the long spacing detectors.

Borehole Quality
The litho-density suffers from the same borehole quality problems as the formation density
tool, because of its similar borehole configuration.

Mud Type
The tool can be used with any muds except those that contain barite
Uses of the PEF Log

Determination of Lithology

Note that there are two common

lithologies that cannot be

distinguished by the gamma ray log

easily. These are clean sandstones

and clean limestone. They can be

very well identified by PEF log.

Determination of Lithology
If there is a mixture of two mineralogies, for
example a sandy limestone, a crossplot
technique or a simple mixing rule can be
applied to calculate the relative proportions of
the two mineralogies.

where:
(Pe)log = the value of Pe measured in the zone of
interest
(Pe)1 = the value of Pe measured in mineralogy 1
(Pe)2 = the value of Pe measured in mineralogy 2
x1 = the volume fraction of mineralogy 1, where
x1+x2=1.0.
(1-x1) = the volume fraction of mineralogy 2, where
x1+x2=1.0.
Uses of the PEF Log

Determination of Lithology

When three minerals are present (plus porosity), the Pe log values are used together with the formation

density log values. The minerals are obtained from a cross-plot of the apparent bulk density ρmaa of the

matrix against the apparent value of U for the matrix Umaa.

Detection of Heavy Minerals

 These heavy mineral bands with characteristic signatures can be very useful in the correlation of
formations between wells.