Global LCD Panel Exchange Center www.panelook.

com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

( V ) Preliminary Specifications
( ) Final Specifications

Module 13.3” WXGA Color TFT-LCD

Model Name B133EW03 V0

Customer Date Approved by Date

Jerry Chen 08/21/2008

Checked &
Prepared by
Approved by

WeiHsiang Lo 08/21/2008

Note: This Specification is subject to change NBBU Marketing Division /

without notice. AU Optronics corporation

document version 0.3 1/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

Contents
1. Handling Precautions .............................................................................................................. 4
2. General Description ................................................................................................................. 5
2.1 General Specification ......................................................................................................................5
2.2 Optical Characteristics ....................................................................................................................6
3. Functional Block Diagram..................................................................................................... 11
4. Absolute Maximum Ratings .................................................................................................. 12
4.1 Absolute Ratings of TFT LCD Module..........................................................................................12
4.2 Absolute Ratings of Backlight Unit ...............................................................................................12
4.3 Absolute Ratings of Environment ..................................................................................................12
5. Electrical characteristics....................................................................................................... 13
5.1 TFT LCD Module.........................................................................................................................13
5.2 Backlight Unit...............................................................................................................................15
6. Signal Characteristic ............................................................................................................. 17
6.1 Pixel Format Image.......................................................................................................................17
6.2 The input data format....................................................................................................................18
6.3 Signal Description/Pin Assignment ................................................................................................19
6.4 Interface Timing............................................................................................................................21
7. Connector Description .......................................................................................................... 23
7.1 TFT LCD Module.........................................................................................................................23
7.2 Backlight Unit...............................................................................................................................23
7.3 Signal for Lamp connector ............................................................................................................23
8. Vibration and Shock Test ...................................................................................................... 24
8.1 Vibration Test ...............................................................................................................................24
8.2 Shock Test Spec: ..........................................................................................................................24
9. Reliability ................................................................................................................................ 25
10. Mechanical Characteristics ................................................................................................. 26
10.1 LCM Outline Dimension .............................................................................................................26
11. Shipping and Package......................................................................................................... 28
11.1 Shipping Label Format ................................................................................................................28
11.2. Carton package ..........................................................................................................................29
11.3 Shipping package of palletizing ...................................................................................................29

document version 0.3 2/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

Record of Revision

Version and Date Page Old description New Description Remark

0.1 2008/8/21 All First Edition for Customer

document version 0.3 3/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

1. Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration
or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it
was taken out from the container, do not press the center of the CCFL Reflector
edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the
TFT Module may be damaged.
10)At the insertion or removal of the Signal Interface Connector, be sure not to rotate
nor tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
12)Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13)Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source(, IEC60950 or UL1950), or be applied exemption.
14)The LCD module is designed so that the CCFL in it is supplied by Limited Current
Circuit(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.

document version 0.3 4/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

2. General Description
B133EW03 V0 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD
panel, a driver circuit, and backlight system. The screen format is intended to support the
WXGA (1280(H) x 800(V)) screen and 262k colors (RGB 6-bits data driver). All input
signals are LVDS interface compatible. Inverter of backlight is not included.
B133EW03 V0 is designed for a display unit of notebook style personal computer and
industrial machine.

2.1 General Specification

The following items are characteristics summary on the table at 25  condition:
Items Unit Specifications
Screen Diagonal [mm] 337.8 (13.3W”)
Active Area [mm] 286.08 X 178.8

Pixels H x V 1280x3(RGB) x 800

Pixel Pitch [mm] 0.2235X0.2235

Pixel Format R.G.B. Vertical Stripe

Display Mode Normally White

White Luminance (ILED=16mA) [cd/m2] 220 typ. (5 points average)

(Note: ILED is LED current) 187 min. (5 points average)
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 500 typ ,
Response Time [ms] 20 typ / 25 Max
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 5.2 max.(without inverter)
Weight [Grams] 340 max.
Physical Size [mm] L W T
Max 299.5 195.5 5.6
Typ 299 195 5.3
Min   
Electrical Interface 1 channel LVDS
Surface Treatment Glare, Hardness 3H,
Reflection ~0.5%

document version 0.3 5/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

Support Color 262K colors ( RGB 6-bit )

Temperature Range
Operating [oC] 0 to +50
Storage (Non-Operating) [oC] -25 to +65
RoHS Compliance RoHS Compliance

2.2 Optical Characteristics

The optical characteristics are measured under stable conditions at 25 (Room Temperature) :
Item Unit Conditions Min. Typ. Max. Note
2
White Luminance [cd/m ] 5 points average 187 220 - 1, 4, 5.

Viewing Angle [degree] Horizontal - 70 - 4, 9

[degree] (Right)
- 70 -
CR = 10 (Left)
[degree] Vertical - 60 -
[degree] (Upper)
- 60 -
CR = 10 (Lower)
Luminance 5 Points - - 1.25 1, 3, 4
Uniformity
Luminance 13 Points - - 1.50 2, 3, 4
Uniformity
CR: Contrast Ratio DCR:Off 300 500 - 4, 6
Cross talk % 4 4, 7
Response Time [msec] Rising - - - 4, 8
[msec] Falling - - -
[msec] Rising + Falling - 20 25
Red x 0.594 0.614 0.634
Red y 0.312 0.332 0.352
Green x 0.284 0.304 0.324
Chromaticity of color
Coordinates Green y 0.535 0.555 0.575 4, 9
(CIE 1931) Blue x 0.139 0.159 0.179
Blue y 0.107 0.127 0.147
White x 0.283 0.313 0.343
White y 0.299 0.329 0.359

document version 0.3 6/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

Note 1: 5 points position (Display area : 286.08 (H) x 178.8 (V)mm)

W /4 W /4 W /4 W /4

H /4

1 2
H /4

H 3

H /4

4 5

H /4

Note 2: 13 points position

Note 3: The luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by
the minimum test point luminance

Maximum Brightness of five points

W5 =
Minimum Brightness of five points

Maximum Brightness of thirteen points

W13 =
Minimum Brightness of thirteen points

document version 0.3 7/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

Note 4: Measurement method

The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be executed after
lighting Backlight for 30 minutes in a stable, windless and dark room.
Photo detector

Field=2

50 cm

LCD Panel TFT-LCD

Center of the screen

Note 5 Definition of Average Luminance of White (YL):

Measure the luminance of gray level 63 at 5 pointsYL = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L (x) is corresponding to the luminance of the point X at Figure in Note (1).

Note 6 Definition of contrast ratio:

Contrast ratio is calculated with the following formula.

Brightness on the “White” state

Contrast ratio (CR)=
Brightness on the “Black” state

document version 0.3 8/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

Note 7 Definition of Cross Talk (CT)

CT = | YB – YA | / YA  100 (%)

Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)

YB = Luminance of measured location with gray level 0 pattern (cd/m2)

Note 8: Definition of response time:

The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval
between the 10% and 90% of amplitudes. Refer to figure as below.

"Black"
"White" "White"
100%
90%

Optical
Response

10%
0%
Tr Tf

document version 0.3 9/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

Note 8. Definition of viewing angle

Viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180° horizontal and
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90°
() horizontal left and right and 90° ( ) vertical, high (up) and low (down). The measurement direction is
typically perpendicular to the display surface with the screen rotated about its center to develop the desired
measurement viewing angle.

document version 0.3 10/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

3. Functional Block Diagram

The following diagram shows the functional block of the 13. 3inches wide Color TFT/LCD Module:

X-Driver

(4 pairs LVDS) LCD DRIVE

BOARD
RxIN0
RxIN1 LCD
RxIN2 Controller TFT ARRAY/CELL
RxCLKIN 1280(R/G/B) x 3 x 800
DC-DC
Converter
Ref circuit
Backlight Unit
Y-Driver
VDD
GND
LCD Connector(30pin) Lamp Connector(2pin)

document version 0.3 11/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

4. Absolute Maximum Ratings

Absolute maximum ratings of the module are as following:

4.1 Absolute Ratings of TFT LCD Module

Item Symbol Min Max Unit Conditions
Logic/LCD Drive Vin -0.3 +4.0 [Volt] Note 1,2

4.2 Absolute Ratings of Backlight Unit

Item Symbol Min Max Unit Conditions
CCFL Current ICCFL - 6.5 [mA] rms Note 1,2

4.3 Absolute Ratings of Environment

Item Symbol Min Max Unit Conditions
o
Operating Temperature TOP 0 +50 [ C] Note 3
Operation Humidity HOP 5 95 [%RH] Note 3
o
Storage Temperature TST -20 +60 [ C] Note 3
Storage Humidity HST 5 95 [%RH] Note 3

Note 1: At Ta (25 )
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS(Incoming Inspection Standard).

Twb=39°C

Operating Range Storage Range

document version 0.3 12/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;

Symble Parameter Min Typ Max Units Note

VDD Logic/LCD Drive 3.0 3.3 3.6 [Volt]
Voltage
PDD VDD Power ˄ˁ˃ [Watt] Note 1
IDD IDD Current 200 2500 [mA] Note 1
IRush Inrush Current 1500 [mA] Note 2
VDDrp Allowable 100 [mV]
Logic/LCD Drive p-p
Ripple Voltage

Note 1 : Maximum Measurement ConditionBlack Patterm

Note 2Measure Condition

+3.3V Q3
AO6402
D6 F1
D5
D2 S
VCC
D1

R1 (LCD Module Input)

G

47K
C1
1uF/16V
(High to Low)
D1
D2
D5
D6

Control
Signal Q3
R2 AO6402
G
S

1K
C3
2

+12.0V
SW1
SW MAG-SPST VR1 0.01uF/25V
1

R2
47K

1K

C2
1uF/25V

90% 3.3V

10%
0V
0.5ms

Vin rising time

document version 0.3 13/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

5.1.2 Signal Electrical Characteristics

Input signals shall be low or High-impedance state when VDD is off.
It is recommended to refer the specifications of THC63LVDF84A (Thine Electronics Inc.)
in detail.

Signal electrical characteristics are as follows;

Parameter Condition Min Max Unit

Differential Input High
Vth Threshold (Vcm=+1.2V) 100 [mV]
-

Differential Input Low

Vtl Threshold (Vcm=+1.2V) -100 [mV]
-

Differential Input
Vcm 1.125 1.375 [V]
Common Mode Voltage

Note: LVDS Signal Waveform

V
t

Vcm

VSS

document version 0.3 14/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

5.2 Backlight Unit

Parameter guideline for CCFL Inverter

Parameter Min Typ Max Units Condition

White Luminance
5 points average 200 220 - [cd/m2 ]
(Ta=25)
CCFL current(ICCFL) 2.0 6.0 7.0 [mA] rms (Ta=25)
Note 2
CCFL Frequency(FCCFL) 45 62 70 [KHz] (Ta=25)
Note 3,4
CCFL Ignition Voltage(Vs) 1315 [Volt] rms (Ta= 0)
Note 5
CCFL Ignition Voltage(Vs) 1095 [Volt] rms (Ta= 25)
Note 5
CCFL Voltage (Reference) 608 640 672 [Volt] rms (Ta=25)
(VCCFL) Note 6
CCFL Power consumption - 3.85 4.2 [Watt] (Ta=25)
(PCCFL) Note 6

Note 1: Typ are AUO recommended Design Points.

*1 All of characteristics listed are measured under the condition using the AUO Test inverter.
*2 In case of using an inverter other than listed, it is recommended to check the inverter carefully.
Sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low
power may happen.
*3 In designing an inverter, it is suggested to check safety circuit very carefully. Impedance of CCFL, for
instance, becomes more than 1 [M ohm] when CFL is damaged.
*4 Generally, CCFL has some amount of delay time after applying kick-off voltage. It is recommended to
keep on applying kick-off voltage for 1 [Sec] until discharge.
*5 CCFL discharge frequency must be carefully chosen so as not to produce interfering noise stripes on
the screen.
*6 Reducing CCFL current increases CCFL discharge voltage and generally increases CCFL discharge
frequency. So all the parameters of an inverter should be carefully designed so as not to produce too
much leakage current from high-voltage output of the inverter.
Note 2: It should be employed the inverter which has “Duty Dimming”, if ICCFL is less than 4mA.
Note 3: CCFL discharge frequency should be carefully determined to avoid interference between inverter and
TFT LCD.

document version 0.3 15/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

Note 4: The frequency range will not affect to lamp life and reliability characteristics.
Note 5: CCFL inverter should be able to give out a power that has a generating capacity of over 1,430
voltage. Lamp units need 1,400 voltage minimum for ignition.
Note 6: Calculator value for reference (ICCFL×VCCFL=PCCFL)
Note 7: Requirements for a system inverter design, which is intended to have a better display performance, a
better power efficiency and a more reliable lamp, are following.
It shall help increase the lamp lifetime and reduce leakage current.
a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion rate of the waveform should bewithin
2 10%.
* Inverter output waveform had better be more similar to ideal sine wave.

document version 0.3 16/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.

0 1 1278 1279

1st Line R GB R GB R GB R GB

800th Line R GB R GB R GB R GB

document version 0.3 17/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

6.2 The input data format

Signal Name Description

R5 Red Data 5 (MSB) Red-pixel Data
R4 Red Data 4 Each red pixel's brightness data consists of
R3 Red Data 3 these 6 bits pixel data.
R2 Red Data 2
R1 Red Data 1
R0 Red Data 0 (LSB)
Red-pixel Data
G5 Green Data 5 (MSB) Green-pixel Data
G4 Green Data 4 Each green pixel's brightness data consists
G3 Green Data 3 of these 6 bits pixel data.
G2 Green Data 2
G1 Green Data 1
G0 Green Data 0 (LSB)
Green-pixel Data
B5 Blue Data 5 (MSB) Blue-pixel Data
B4 Blue Data 4 Each blue pixel's brightness data consists of
B3 Blue Data 3 these 6 bits pixel data.
B2 Blue Data 2
B1 Blue Data 1
B0 Blue Data 0 (LSB)
Blue-pixel Data
RxCLKIN Data Clock The typical frequency is 69.3 MHZ.. The
signal is used to strobe the pixel data and
DE signals. All pixel data shall be valid at
the falling edge when the DE signal is high.
DE Display Timing This signal is strobed at the falling edge of
RxCLKIN. When the signal is high, the pixel
data shall be valid to be displayed.
VS Vertical Sync The signal is synchronized to RxCLKIN .
HS Horizontal Sync The signal is synchronized to RxCLKIN .
Note: Output signals from any system shall be low or High-impedance state when VDD is
off.

document version 0.3 18/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0
6.3 Signal Description/Pin Assignment

LVDS is a differential signal technology for LCD interface and high speed data transfer device.
PIN NO Symbol Function
1 GND Ground
2 VDD +3.3V Power Supply
3 VDD +3.3V Power Supply
4 VEDID +3.3V EDID Power
5 AG_IN No Connection (Reserve for AUO test)
6 CLKEDID EDID Clock Input
7 DATAEDID EDID Data Input
8 ORXIN0N LVDS differential clock input
9 ORXIN0P LVDS differential clock input
10 GND Ground
11 ORXIN1N LVDS differential clock input
12 ORXIN1P LVDS differential clock input
13 GND Ground
14 ORXIN2N LVDS differential clock input
15 ORXIN2P LVDS differential clock input
16 GND Ground
17 ORXIN3N LVDS differential clock input
18 ORXIN3P LVDS differential clock input
19 GND Ground
20 NC No Connection (Reserve for AUO test)
21 NC No Connection (Reserve for AUO test)
22 NC No Connection (Reserve for AUO test)
23 NC No Connection (Reserve for AUO test)
24 NC No Connection (Reserve for AUO test)
25 NC No Connection (Reserve for AUO test)
26 NC No Connection (Reserve for AUO test)
27 NC No Connection (Reserve for AUO test)
28 NC No Connection (Reserve for AUO test)
29 NC No Connection (Reserve for AUO test)
30 NC No Connection (Reserve for AUO test)

document version 0.3 19/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0
Note1: Start from right side

Pin1 Pin30

document version 0.3 20/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

6.4 Interface Timing

6.4.1 Timing Characteristics
Basically, interface timings should match the 1280x800 /60Hz manufacturing guide line
timing.

Parameter Symbol Min. Typ. Max. Unit

Frame Rate - 50 60 - Hz
Clock frequency 1/ TClock 50 69.3 80 MHz
Period TV 808 823 -
Vertical
Active TVD - 800 - TLine
Section
Blanking TVB 8 23 -
Period TH - 1440 -
Horizontal
Active THD - 1280 - TClock
Section
Blanking THB - 160 -

Note : DE mode only

6.4.2 Timing diagram

TCLOCK Input Timing Definition ( DE Mode)

DOTCLK

Input Invaild Pixel Pixel Pixel Pixel Pixel Invaild Pixel

Data Data 1 2 3 N-1 N Data 1

DE
THB THD

TH

DE
TVB
TVD

TV

document version 0.3 21/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

6.5 Power ON/OFF Sequence

VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the
chart. Signals from any system shall be Hi-Z state or low level when VDD is off.

T1
90% 90%

10% 10%
Power Supply VDD T3 T7 T4
T2

VALID
LVDS Interface
T5 DATA

T6

Backlight On

Power Sequence Timing

Value
Parameter Min. Typ. Max. Units

T1 0.5 - 10 (ms)
T2 0 - 50 (ms)
T3 0 - 50 (ms)
T4 400 - - (ms)
T5 200 - - (ms)
T6 200 - - (ms)
T7 0 - 10 (ms)

document version 0.3 22/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

7. Connector Description

Physical interface is described as for the connector on module.

These connectors are capable of accommodating the following signals and will be
following components.

7.1 TFT LCD Module

Connector Name / Designation For Signal Connector

Manufacturer IPEX
Type / Part Number IPEX 20347-330E-12

Mating Housing/Part Number IPEX 20345-030T-31

7.2 Backlight Unit

Physical interface is described as for the connector on module.

These connectors are capable of accommodating the following signals and will be
following components.

Connector Name / Designation For Lamp Connector

Manufacturer JST
Type / Part Number BHSR-02VS-1
Mating Type / Part Number SM02B-BHSS-1-TB

7.3 Signal for Lamp connector

Pin # Cable color Signal Name

1 Red Lamp High Voltage

2 White Lamp Low Voltage

document version 0.3 23/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

8. Vibration and Shock Test

8.1 Vibration Test

Test Spec:
 Test method: Non-Operation
 Acceleration: 1.5G , sine wave
 Frequency: 10 - 500Hz Random
 Sweep: 30 Minutes each Axis (X, Y, Z)

8.2 Shock Test Spec:

Test Spec:
 Test method: Non-Operation
 Acceleration: 200 G , Half sine wave
 Active time: 2 ms
 Pulse: X,Y,Z .one time for each side

document version 0.3 24/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

9. Reliability

Items Required Condition Note

Temperature
40/90%,300Hr
Humidity Bias
High Temperature
60/Dry,300Hr
Operation
Low Temperature
0,300Hr
Operation
On/Off Test 25, ON/30 sec. OFF/30sec., 10,000 cycles)
Hot Storage 60/35% RH ,250 hours
Cold Storage -20/50% RH ,250 hours
Thermal Shock Test -20/30 min ,60/30 min 100cycles
Hot Start Test 50/1 Hr min. power on/off per 5 minutes, 5 times
Cold Start Test 0/1 Hr min. power on/off per 5 minutes, 5 times
Shock Test
200G, 2ms, Half-sine wave
(Non-Operating)

Vibration Test Sine-wave vibration, 1.5 G zero-to-peak, 10 to 500 Hz,

(Non-Operating) 30 mins in each of three mutually perpendicular axes.

Contact : 8KV/ operation Note 1

ESD
Air : 15KV / operation
Room temperature
25, 2000hours, Operating with loop pattern
Test

Note1: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
. Self-recoverable. No hardware failures.
Note2: CCFL Life time: 10,000 hours minimum under normal module usage.
Note3: MTBF (Excluding the CCFL): 30,000 hours with a confidence level 90%

document version 0.3 25/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

10. Mechanical Characteristics

10.1 LCM Outline Dimension

document version 0.3 26/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

document version 0.3 27/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

11. Shipping and Package

11.1 Shipping Label Format

V.0
*V18wwzzzz21QA

document version 0.3 28/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

Product Specification
AU OPTRONICS CORPORATION
B133EW03 V0

11.2. Carton package

11.3 Shipping package of palletizing

Top cardboard

Stretch film

Label PET band

Corner angle

Bottom cardboard
Wooden pallet

document version 0.3 29/29

PDF created with pdfFactory trial version www.pdffactory.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com