Scribd
Upload
58 views

Grid Design: Match To Objective of Study

1. Grid design criteria include adequately representing reservoir geometry, identifying pressures and saturations at specific locations, and correctly modeling fluid mechanics. 2. Numerical dispersion can distort simulations by decreasing displacement efficiency and smearing fronts. It can be limited by increasing grid resolution, improved mobility weighting, and pseudofunctions. 3. Grid orientation relative to well locations influences performance, with diagonal orientation generally better representing sweep efficiency and front arrival times.

Uploaded by

Guluzada Ulvi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
58 views

Grid Design: Match To Objective of Study

1. Grid design criteria include adequately representing reservoir geometry, identifying pressures and saturations at specific locations, and correctly modeling fluid mechanics. 2. Numerical dispersion can distort simulations by decreasing displacement efficiency and smearing fronts. It can be limited by increasing grid resolution, improved mobility weighting, and pseudofunctions. 3. Grid orientation relative to well locations influences performance, with diagonal orientation generally better representing sweep efficiency and front arrival times.

Uploaded by

Guluzada Ulvi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 20

Grid Design

tank 1D 1D Radial

Cross-sectional Areal

2D radial 3D Mattax & Dalton

Match to objective of study


Criteria for selecting gridblock size
Desired location
1. Able to identify
saturations and pressures
at specific locations and
times
Existing wells Gridblock

≥ 3 blocks between locations


Criteria for selecting gridblock size
2. Adequately represent the geometry/geology and
physical properties of the reservoir

Ertekin,et al.
Criteria for selecting gridblock size
Structure Map and
Overlying grid

Mattax & Dalton


Criteria for selecting gridblock size

Malhotra

Malhotra
Criteria for selecting
gridblock size
3. Sufficient to describe the
dynamics
a. Able to describe pressures
as f(t)
b. Able to follow front
locations and movement
c. Able to correctly
represent well behavior

Mattax & Dalton


Criteria for selecting gridblock size
4. Correctly model the reservoir fluid mechanics; for
example: coning, displacement

5. Compatible with the mathematics of the simulator


Numerical Dispersion
• Artifact of numerical analysis techniques
• Can cause severe distortions in simulations,
especially in rapid saturation changes
1 2 3 4

Sw Sw

x x

If upstream mobility, then water will flow


From Blocks 2 to 3. Next time step, water
Flows from 3 to 4.
Numerical Dispersion
• Effect is to decrease displacement efficiency at
breakthrough
• Most serious for favorable mobility ratios
• Tends to smear the front

Mattax & Dalton


Gridsize Guidelines
• No general rule for proper cell size
• Perform sensitivity analysis
• Rule of thumb
– 3 to 5 blocks between producers
– 5 to 10 between producers/injectors
Limiting Numerical Dispersion
1. Increase number of gridblocks
2. Improved upstream, mobility weighting
3. Apply pseudofunctions
relative permeability curves in areal models are modified to restrict the
movement of the displacing phase until saturation reaches the finely
gridded simulation value.
4. Finite Element Modelling (FEM)
Grid Orientation Effect
• Performance influenced by the orientation of the
grid relative to the well locations.
• Multi-dimensional, multiphase problem
• Important when M displacing phase >> M displaced phase
A
-flow path from Well B longer,
Thus front will arrive later

B
- but sweep efficiency greater…
Higher oil recovery
Grid Orientation
Effect

Parallel model

Diagonal model
Grid Orientation Effect
Case I: Unit mobility, diagonal grid
1.0

- Gridblock size (Δx) varied


PVrec

From 0.05 to 0.20.

- Results insensitive to number


Of gridblocks
0.4
0.5 PVinj 1.5
Grid Orientation Effect
Case II: Unit mobility, parallel grid
1.0

-Oil recovery increases as grid


PVrec

i n g block size decreases,


ea s
cr
In Δx -but is less than diagonal model
for all grid spacings
0.4
0.5 PVinj 1.5
Grid Orientation Effect
Case III: Unfavorable mobility ratio (10:1)

1.0 Diagonal

9 point formulation
PVrec

Parallel

Increasing
Δx
0.4
0.5 PVinj 1.5
Grid Orientation Effect
• For simulations with favorable to slightly
favorable mobility ratio…grid orientation
effect can be reduced by refining the grid.
• Diagonal orientation less likely to introduce
distortion.
• Grid orientation effect more pronounced for
unfavorable mobility ratios (10:1)
Grid Orientation Effect
Orient grid parallel to
principal directions
A
of permeability…….
if known.. C
kmax

B
kmin

Robinson

Strike curvature map


Approaches to Reduce Grid
Orientation Effect
1. Nine point formulation
2. Initialize with high displacing phase
saturation near injection wells
3. Two-point upstream weighting
4. Curvilinear coordinates
5. Triangular grid systems
6. F.E.M.
Selection of Timestep
• Selection function of study; e.g. single well
pressure test vs. full field reservoir simulation
• Consequences of large time step
– Incorrect mobilities
– Numerical dispersion
– Physics of system not represented
• Initialization
• Automatic timestep
– Controlling parameters are pressure and saturation
change

You might also like