Scribd
Upload
64 views1 page

CNC Machine and Automation 6 Exam/Mech./Prod/T&DM/5525/May'19 Duration: 3Hrs. M.Marks:75 Section-A Q1. Fill in The Blanks. 10x1.5 15

This document contains questions from an exam on CNC machines and automation. Section A has 10 one-mark multiple choice questions covering topics like punched tape codes, MCU functions, tool types, programming methods, subroutines, transducers, limit switches, production types, and reference points. Section B has 5 six-mark questions on CNC applications, automatic tool changers, canned cycles, analog vs digital systems, FMS components, group technology pros and cons, and work holding devices. Section C has 3 ten-mark questions on DNC systems, fault finding techniques, and sensor parameters and types.

Uploaded by

Simranjeet Singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
64 views1 page

CNC Machine and Automation 6 Exam/Mech./Prod/T&DM/5525/May'19 Duration: 3Hrs. M.Marks:75 Section-A Q1. Fill in The Blanks. 10x1.5 15

This document contains questions from an exam on CNC machines and automation. Section A has 10 one-mark multiple choice questions covering topics like punched tape codes, MCU functions, tool types, programming methods, subroutines, transducers, limit switches, production types, and reference points. Section B has 5 six-mark questions on CNC applications, automatic tool changers, canned cycles, analog vs digital systems, FMS components, group technology pros and cons, and work holding devices. Section C has 3 ten-mark questions on DNC systems, fault finding techniques, and sensor parameters and types.

Uploaded by

Simranjeet Singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

S.B.

Roll No……………………………………

CNC MACHINE AND AUTOMATION


6th Exam/Mech./Prod/T&DM/5525/May’19
Duration: 3Hrs. M.Marks:75
SECTION-A
Q1. Fill in the blanks. 10x1.5=15
a. The punched tape contains __________for NC Machine.
b. MCU mounted on the machine tool is called __________.
c. The PVD tools are preferred for _________ cuts.
d. Manual part programming is _________than computer aided part programming.
e. Subroutines do loops and fixed cycles are used for__________ programming.
f. Potentiometers are __________transducers.
g. Limit switches are used to determine______ position of travel.
h. Programmable automation is suitable for __________ production.
i. FMS stands for ___________.
j. In absolute NC system, all the commands are referred from_________ point.

SECTION-B
Q2. Attempt any five questions. 5x6=30
i. What are the various applications of CNC machines?
ii. Write a short note on ATC (Automatic Tool Changer).
iii. What do you mean by canned cycle? Also write down its advantages in programming CNC
machines.
m
iv. Differentiate between Analog and Digital systems.
o
v. Write a short note on FMS and its components.

. c
vi. What are the pros and cons of group Technology?

r
vii. What are the characteristics of a good work holding device?

p e SECTION-C
m
p a
Q3. Attempt any three questions.

c o 3x10=30

r
b. Explain in detail the various functions of a DNC system.
r .
a. What are the various fault-finding techniques used with microprocessor-based systems?

b e
c. What are the various parameters that characterize a Sensor? Explain in detail.
d. Write brief note on followings.
p
i. Swarf removal
ii. Potentiometers
p a
b r

You might also like