Scribd
Upload
536 views2 pages

MSDS Primer S1301-M Parte A

This document provides product data on S1301-M epoxy primer. It is a 2 component 100% solids epoxy primer used for corrosion protection of field welded pipe joints. The document details the product description, recommended uses, specifications including mixing ratio, coverage, pot life, shelf life, and ordering information.

Uploaded by

Michael Betetta Abad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
536 views2 pages

MSDS Primer S1301-M Parte A

This document provides product data on S1301-M epoxy primer. It is a 2 component 100% solids epoxy primer used for corrosion protection of field welded pipe joints. The document details the product description, recommended uses, specifications including mixing ratio, coverage, pot life, shelf life, and ordering information.

Uploaded by

Michael Betetta Abad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

PRODUCT DATA SHEET

COVALENCE® S1301-M EPOXY PRIMER

Description: S1301-M primer is a specially formulated 100% volume solids (solvent-less) 2 component
epoxy.

Recommended use: As an epoxy primer in a 3 layer polyethylene coating system for superior corrosion protection
of field welded joints of steel pipes. Can be used with Covalence 3 layer coating systems:
HTLP80 (-HP), HTLP60 (-DCS), DIRAX.
For HTLP60-DCS, HTLP80 and DIRAX the epoxy primer needs to be applied on the steel
surface only. For HTLP80-HP* and HTLP60 the epoxy needs to be applied onto the steel
surface AND onto the 3LPE line coating.
When the line coating is (D)FBE or CTE the epoxy need to be applied on the line coating for
all products.
* For certain 3LPE pipeline coatings it is not necessary to put epoxy on the line coating.
Consult your SFL representative for more information.
Colour: Black

Volume solids: 100%

Weight solids: 100%

Mixing ratio: (by volume) : 3 parts of base (part A) to 1 part of hardener (part B)
(by weight) : 5 parts of base (part A) to 1 part of hardener (part B)

Typical coverage: 3.8 sq.m/litre. ( 150 microns or 6 mils average thickness, including drum and application
scrap)
For twin packs and bulk drums for small diameter pipes (< 18”/DN450) include 15% extra
scrap.
For twin packs for pipe diameters (as of 18”/DN450) include 5% extra scrap.

Specific gravity: Base: 1.65


Hardener: 1

Typical thickness: 100-200 microns (4-8 mils)

Pot life: 30 min at 23°C (73°F), 15 min at 40°C (104°F)

Shelf life: 3 years 23°C (73°F, 163°F) from date of manufacturing, out of direct sunlight. Shelf life will
be less at higher temperatures.

Flash point: Part A (Base) : 143°C (289°F)


Part B (Hardener): > 118°C (244°F)

Thinner: Do not dilute.

Application: 1. Prepare the pipe surface as recommended in the product application guide.
2. Pour hardener into base as per mixing ratio. Stir the mixture (max 300 ml in 1 can) for
approximately 1 minute to ensure a homogeneous mixture. For twin packs: remove the clip
and roll the twin pack for min 1 minute, see detailed application guideline on the twin pack.
3. Carefully apply mixed epoxy primer as indicated in the product application guide.

PDS-COVALENCE-S1301-M-V4-DEC19-AARPS-0680 Page 1 / 2
PRODUCT DATA SHEET COVALENCE® S1301-M EPOXY PRIMER

S1301 M Pot Life and Gel Time Chart:

Temperature Pot life Gel time Dry time Shore D70


20°C 54 min 64 min 117 min 10 hr
25°C 29 min 59 min 105 min 8 hr 30 min
30°C 20 min 52 min 80 min 4 hr 30 min
35°C 13 min 46 min 62 min 3 hr
40°C 11 min 35 min 43 min 1 hr 50 min

Note:
1. Pot life date are obtained by mixing 600 g of Part A and 120 g of Part B. Part A and
Part B temperature before mixing is as specified (20, 25, 30, 35 or 40 degrees C) and
keep the mixture at the environment of that temperature after mixing.
2. Gel time, dry time and Shore D70 date are from 40-60 mils thin film.

Ordering info: Twin packs:


The twin packs are available as single twin packs or as a kit with applicator pad and 1 pair of
nitrile safety gloves.

Single twin pack: S1301-M-TP-200ML-300GR(C18)


Twin pack kit with EQ-PR-APPLICATOR-3 (foam pad with felt) & safety gloves:
S1301-M-TP-200ML-300GR-KT3(C10)

Other twin pack sizes are made to order only with MOQ of 5000 pc. Min. size is 75 ml, max.
size is 300 ml.
Order quantity should be multiples of box quantity xxx indicated in the product description
(Cxx).

Bulk Epoxy:
Base : S1301-M-PART-A-18L-29.7KG
Hardener: S1301-M-PART-B-18L-18KG
Always order in multiples of 3 pails of part A by 1 pail of part B.
For accessories to apply epoxy see PDS-ACCESSORIES. These need to be ordered
separately.

Information
Documentation Extensive information is available on our web-site. Application instructions and other documentation can be obtained by
contacting our head office, from our local distributor or by sending an email to [email protected]
Certified staff Application of the described coating system shall be carried out by certified personnel.

PDS-COVALENCE-S1301-M-V4-DEC19-AARPS-0680 Page 2 / 2

You might also like