ASNA2050

Issue : R

SOLID RIVET - ALUMINIUM ALLOY, UNIVERSAL HEAD Date : 07.12

Page : 1/9

SUMMARY
1 -  SCOPE AND FIELD OF APPLICATION 

2 -  NORMATIVE REFERENCES 

3 -  TERMINOLOGY 

4 -  REQUIRED CHARACTERISTICS 

5 -  DESIGNATION 

6 -  MARKING 

7 -  TECHNICAL SPECIFICATION 

8 -  MANUFACTURERS 

AMENDMENT RECORD SHEET

1 - SCOPE AND FIELD OF APPLICATION

This standard specifies the dimensions, tolerances, required characteristics and the masses of
aluminium solid rivet with universal head.

2 - NORMATIVE REFERENCES

The following referenced documents are indispensable for the application of this document. For
dated references, only the edition cited applies. For undated references, the last edition of the
referenced document (including any amendments) applies.

EN2115 Aerospace series - Aluminium alloy 2117-T42 - Wire for solid rivets D ≤ 10 mm.
:
EN2116 Aerospace series - Aluminium alloy 2017A-T42 - Wire for solid rivets D ≤ 10 mm.
:
EN2424 :
Aerospace series - Marking of aerospace products.
EN3115 Aerospace series - Aluminium alloy 7050- T73 - Wire for solid rivets D ≤ 10 mm.
:
EN6104 :
Aerospace series - Rivets, solid, in aluminium or aluminium alloy - Inch series -
Technical specification.
MIL-DTL-5541:Chemical conversion coatings on aluminium and aluminium alloys.

The content of this document is the property of AIRBUS FRANCE. It is supplied in confidence and commercial security on its contents must be
maintained. It must not be used for any purpose other than that for which it is supplied nor may information contained in it be disclosed to
unauthorized persons. It must not be reproduced in whole or in part without permission in writing from AIRBUS FRANCE.
AIRBUS FRANCE Trade Secrets or Commercial or Financial information, 5 U.S.C. (b) (4).

© AIRBUS FRANCE 1984. All rights reserved

ASNA2050
Issue : Jul 08
Page : 2

3 - TERMINOLOGY

Not applicable.

4 - REQUIRED CHARACTERISTICS

4.1 - Configuration, dimensions, tolerances, solid rivet length and mass

4.1.1 - The configuration shall be in accordance with figure 1.

4.1.2 - The dimensions shall be in accordance with figure 1 and table 1.

4.1.3 - The tolerances shall be in accordance with figure 1, table 1 and table 2.

Coaxial tolerance of head relative to shank is 0,25mm (TIR).

Maximum inclination of head relative to shank axis is 0° 30'.

4.1.4 - The solid rivet lengths shall be in accordance with table 2.

4.1.5 - The mass shall be in accordance with table 2.

4.2 - Materials, finishes

Materials and finishes shall be in accordance with table 3.

B L

Marking see chapter 6

r2
r1
ØD

r3
ØA

Figure 1 - Configuration

AIRBUS FRANCE 1984. All rights reserved

 ASNA2050
Issue : 07.12
Page : 3

Table 1 – Dimensions and tolerances

DIAMETER NOMINAL Ø D* ØA B C S r1 r2 r3
CODE DIAMETER + 0,25 Ref. Ref. Ref ±
0
0,25
min. max. min. max.
16 1,6 1,55 1,64 3,05 3,35 0,7 0,4 0,40 1,4 0,48

24 2,4 2,36 2,42 4,50 4,90 1,0 0,6 0,58 2,1 0,73

32 3,2 3,15 3,21 6,10 6,70 1,4 0,8 0,78 2,7 0,99

36 3,6 3,55 3,61 6,80 7,50 1,6 0,9 0,88 3,0 1,11

40 4 3,94 4,00 7,50 8,30 1,7 1,0 0,99 0,10 3,4 1,24
to
48 4,8 4,73 4,79 9,00 10,00 2,0 1,2 1,19 4,2 1,50
0,15
56 5,6 5,53 5,59 10,40 11,60 2,4 1,4 1,37 4,9 1,75

64 6,4 6,33 6,39 12,10 13,30 2,7 1,6 1,57 5,5 1,98

80 8 7,90 7,96 15,10 16,70 3,4 2,0 1,98 6,9 2,49

96 9,6 9,50 9,56 18,10 18,60** 4,1 2,4 2,39 8,3 2,97

Dimensions in mm.

* 0,025mm shank diameter increase is permissible within 2,54mm of the base of the head.
** The modification of the tolerance for diameter code No. 96 is applicable on parts manufactured after
October 2005, parts manufactured under previous revision may be procured and used until stocks are
depleted.
Table 2 – Solid rivet lengths, tolerances and mass

LENGTH DIAMETER CODE

CODE
L ± 0,254 mm 16 24 32 36 40 48 56 64 80 96

04 + + +
Mass (g) 0,04 0,15 0,17
05 + + +
Mass (g) 0,04 0,16 0,23
06 + + +
Mass (g) 0,05 0,17 0,31
07 + + + + +
Mass (g) 0,05 0,18 0,34 0,43 0,55
08 + + + + +
Mass (g) 0,06 0,20 0,36 0,46 0,58
09 + + + + +
Mass (g) 0,06 0,21 0,38 0,49 0,62
(Length codes continued on page 4)

AIRBUS FRANCE 1984. All rights reserved

ASNA2050
Issue : 07.12
Page : 4

Table 2 - (Length codes continued from page 3)

LENGTH DIAMETER CODE

CODE
L ± 0,254 mm 16 24 32 36 40 48 56 64 80 96

10 + + + + + + +
Mass (g) 0,07 0,22 0,39 0,52 0,66 0,92 1,31
11 + + + + + + +
Mass (g) 0,08 0,23 0,41 0,55 0,69 0,98 1,39
12 + + + + + + + + +
Mass (g) 0,08 0,25 0,45 0,58 0,73 1,03 1,45 1,97 2,98
13 + + + + + + +
Mass (g) 0,48 0,61 0,76 1,08 1,52 2,06 3,13
14 + + + + + + +
Mass (g) 0,50 0,64 0,80 1,11 1,59 2,15 3,27
15 + + + + + + +
Mass (g) 0,52 0,67 0,84 1,18 1,66 2,25 3,41
16 + + + + + + +
Mass (g) 0,69 0,87 1,24 1,73 2,34 3,56 5,56
17 + + + + + + +
Mass (g) 0,72 0,91 1,29 1,81 2,43 3,70 5,76
18 + + + + + + +
Mass (g) 0,75 0,94 1,34 1,87 2,52 3,85 5,96
19 + + + + + + +
Mass (g) 0,78 0,98 1,39 1,95 2,61 3,99 6,16
20 + + + + + + +
Mass (g) 0,81 1,02 1,44 2,02 2,70 4,13 6,36
22 + + + + +
Mass (g) 1,55 2,16 2,89 4,42 6,76
24 + + + + +
Mass (g) 1,65 2,30 3,07 4,71 7,16
26 + + + + +
Mass (g) 1,75 2,44 3,25 4,99 7,66
28 + + + + +
Mass (g) 1,85 2,52 3,44 5,28 8,06
30 + + + +
Mass (g) 2,72 3,62 5,56 8,46
32 + + + +
Mass (g) 2,86 3,80 5,85 8,86
35 + + + +
Mass (g) 3,07 4,08 6,28 9,54
40 + + + +
Mass (g) 3,42 4,54 7,00 10,89

AIRBUS FRANCE 1984. All rights reserved

 ASNA2050
Issue : 07.12
Page : 5

(Length codes continued on page 5)

Table 2 - (Length codes continued from page 4)

LENGTH DIAMETER CODE

CODE
L ± 0,254 mm 16 24 32 36 40 48 56 64 80 96

45 + + +
Mass (g) 5,00 7,71 12,24
50 + + +
Mass (g) 5,45 8,43 13,59
55 + +
Mass (g) 9,14 14,94
60 + +
Mass (g) 9,86 16,29
(End)
Lengths missing in table can be created mm by mm, e.g. length code 21 between 20 and 22 mm.

Table 3 – Materials and finishes

DIAMETER NOMINAL MATERIAL MATERIAL FINISH FINISH

CODE DIAMETER CODE CODE
Aluminium alloy 2117-T4
16 to 48 1,6 to 4,8 DC
as per EN2115

Aluminium alloy 2017A-T4 DE * Yellow chromated as per

J
as per EN2116 DX MIL-DTL-5541 class 1A
40 to 96 4,0 to 9,6
Aluminium alloy 7050-T73
DK
as per EN3115
* Replaced by material code DX.
Dimensions in mm.

AIRBUS FRANCE 1984. All rights reserved

ASNA2050
Issue : 07.12
Page : 6

5 - DESIGNATION

Example of part number identification to be used on drawing schedules:

ASNA2050DXJ40 , Solid rivet

Example of part number construction:

ASNA2050 DX J 40 08

Number of standard Length code *

Material code (see table 3) Diameter code (see table 1)

Finish code (see table 3)

* For supplying purpose only.

Note: The new designation is interchangeable with the old designation:

- ASNA2050DXJ040-8 (old designation)
- ASNA2050DXJ4008 (new designation)

6 - MARKING

6.1 - Material identification

The symbol on the solid rivet head shall be in accordance with figure 2.

Solid rivets identification Solid rivets identification Solid rivets identification

for material 2117 for material 2017A for material 7050

0,8 max

Recessed Raised Embossed 0,2mm max.

Dimensions in mm.

Figure 2 – Material identification

AIRBUS FRANCE 1984. All rights reserved

 ASNA2050
Issue : 07.12
Page : 7

6.2 - Manufacturer’s identification

EN2424, category F to be embossed or intended on solid rivets head.

Manufacturer’s identification is required on solid rivet heads for diameter code 32 and larger.

7 - TECHNICAL SPECIFICATION

Aluminium solid rivet shall conform with the requirements of EN6104.

8 - MANUFACTURERS

Refer to the list of qualified manufacturers and products.

AIRBUS FRANCE 1984. All rights reserved

ASNA2050
Issue : 07.12
Page : 8

AMENDMENT RECORD SHEET

Modified
Issue Modification summary Justification
paragraph
A.09.84 New standard.

B.12.84 Standard fully amended.

C.01.87 Marking and coded part number modified.

Classification page numbering modified.

D.03.87 Coded part number modified. Following mistake

E.05.88 Rounded end rivet (optional shape) changed to normal rivet. Ref. 437.056/88
Note for Procurement Departments deleted.

F.11.88 Code "R" restored for Procurement CMS

Departments.

G.04.8 Min. shear strength modified for Ø 4 to 8: Memo. A/DET/EG-

9 280 MPa changed to 270 to 310 MPa. ST of 03.04.89

H.07.89 "Example of designation to be used by Product Support Ref.

Division only" added. 721.313/89/TC

J.10.92 On drawing: dimension r 0,1 to 0,25 changed to r 0,1 to A/DET/CG request

0,15. Memo. 531.112/92
In table: tolerance for dimension B added.

K.04.93 Amended standard. Memo. A/DET/CG

Material modified for Ø 4 to 8: 2017-T4 changed to 2017A- 531.032/93
T4.

L.09.96 Table 1 Finish: Alochrome 1 200 gold color for 2017A and 2117 Request
materials and Alochrome 1 200 light color for 7050 material A/BTE/CD/MP
changed to Alochrome 1 200 gold color or Alochrome 1 200
light color for 2017A, 2117 and 7050 materials.

M.11.9 DX code and 9,6 mm diameter added. WBI

7 Specific requirements for 2017A rivets attached on delivery
condition added.

N.10.04 Chapter TECHNICAL SPECIFICATION updated. In accordance with

technical
specification
ASNA2841

P.10.05 In table 2: tolerance for dimension RT added. Manufacturer

In table 2: dimension Ø A max. for diameter code No. 096 request

modified: 19,90 mm changed to 18,60 mm.

AIRBUS FRANCE 1984. All rights reserved

 ASNA2050
Issue : 07.12
Page : 9

AMENDMENT RECORD SHEET

Modified
Issue Modification summary Justification
paragraph
Shear value for 2117-T4 changed: 195 MPa instead of 180
MPa.

Q Title “Rivet – aluminium alloy, round flat head, for automatic

08.09 or not installation” changed to “Solid rivet – aluminium alloy,

round flat head”
2 Technical specification ASNA2841 deleted and replaced by
EN6104.
References EN2115, EN2116, EN3115 and MIL-DTL-5541
added. Reference NFL21207 deleted and replaced by
EN2424.
Reference ASTM-E-112 deleted and indicated in the
technical specification EN6104.
Table 1 References “C” changed to “C Ref.”, “S” to “S Ref.”
Table 2 Mass for diameter 9,6mm defined.
Table 3 Diameter 40 and 48 added for DC material.
Diameter 24, 32 and 36 added for DE,DC and DK material.
Material and finish specifications added.
Material code DE replaced by DX.
Min. shear strength deleted.
Installation mode deleted.
5 Information regarding Procurement Department and Support
division deleted and replaced by « For supplying purpose
only »
Designation modified. The “O (zero)” in front of the diameter
code has been deleted.
Reference NF L 21 207 has been replaced by the EN2424.
6 Marking for 7050 aluminium harmonized with EN standard.

Squeezing test has been deleted form the chapter 7 of the

issue P.

R 07.12 6.1 Correction of typo for identification of 7050 material in figure

2

AIRBUS FRANCE 1984. All rights reserved