Scribd
Upload
84 views

Using The Keil Debugger Command Line: Μvision Help

The document discusses using the Keil debugger command line to create user functions and log command output to a text file for analysis. User functions in Keil follow C syntax but have limitations like not supporting arrays or pointers. The log command can be used to record variable values to a file from within a debug session. An example user function prints an integer array to the command window, and this output is logged to a file and later analyzed in Python.

Uploaded by

Ahmed Hamouda
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
84 views

Using The Keil Debugger Command Line: Μvision Help

The document discusses using the Keil debugger command line to create user functions and log command output to a text file for analysis. User functions in Keil follow C syntax but have limitations like not supporting arrays or pointers. The log command can be used to record variable values to a file from within a debug session. An example user function prints an integer array to the command window, and this output is logged to a file and later analyzed in Python.

Uploaded by

Ahmed Hamouda
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

Appendix

Using the Keil


Debugger B
Command Line
Introduction
Much can be said about the command line capabilities of the Keil
debugger. In this appendix I will focus on writing user functions
and using the log capability to log what is seen in the command
output display to a text file. Many other capabilities exist and
may at some point be described in this appendix.

Getting Started via μVision Help


The help system contains a vast quantity of information on all of
Keil, you just need to jump in and try to find it. For help on the
command line debugging drill down as follows:
...

...
...

Topics of
Interest
Appendix B • Using the Keil Debugger Command Line

Creating User Functions


• To create a user defined function you can use a text editor, or
more conveniently use the build-in Function Editor, which
you access from the Debug menu during a debug session:

Last menu
entry here
brings up the
editor (when
debugging)

• Debugger functions follow closely C syntax, but the language


support is limited
– For example functions cannot pass arrays or pointers
– You cannot directly read and write to a file
– You can however access all of the variables in the debug

B–2 ECE 5655/4655 Real-Time DSP


Creating User Functions

session, e.g. scalar variables and arrays


– Multiple functions can be contained in a use function file (
file extension is .ini)
• Fortunately you have access to both Debug Commands and
Debug Functions
– A very useful Debug Function is printf(), which
behaves very much like the C version
– A very useful Debug Command is log
– Note: The save command can be used to write a block of
memory to a file, but the format is Intel hex, which
requires further post processing to be used in external anal-
ysis
• Appendix A talks about the use of the serial port for sending
debug data directly to a terminal or perhaps a GUI app run-
ning on the host
• By writing a User Function you have the further option of
pre-processing any user variables and sending them to the
Command output window as result of your issuing a debug
command
– This can only be done within a debug session, but your
program may running or stopped
– Note: You can also write to variables
• Command line debug sessions can also be logged to a text
file for later analysis

ECE 5655/4655 Real-Time DSP B–3


Appendix B • Using the Keil Debugger Command Line

– log >fname //starts logging in the file fname


– log off //stops the logging
• A sample .ini file which contains two function is shown
below:
/*******************************************************
Write array contents using debug command line
********************************************************
//For int16_t buffer use:
log >fname
p_int16_buf(1000)
log off

//For float or float32_t buffer use:


log >fname
p_float_buf(1000)
log off

********************************************************
//To load these functions into the debugger workspace
(1) Run the Function editor and then compile
or
(2) At the debug command line type
include buffer_save.ini

Mark Wickert February 2015


*******************************************************/

func void p_int16_buf(int N) {


int i;
for (i=0; i< N; i++) {
//printf("The value is %d\n",buffer[i]);
printf("%d\n",buffer[i]);
}
}

func void p_float_buf(int N) {


int i;
for (i=0; i< N; i++) {
//printf("The value is %6.4f\n",buffer[i]);
printf("%6.4f\n",buffer[i]);
}
}

B–4 ECE 5655/4655 Real-Time DSP


Creating User Functions

• A summary of the steps needed to compile/include the .ini


file in your debug session is given at the top of the file
• The commands needed to create a log file of a 1000 point
int16_t variables named buffer, is also given
• A screen shot of the Command window output following the
above steps is shown below:
Start logging
Print 1000 values of the
array referenced in the
function p_int16_buf

The full listing will scroll by


in the window

• A great tool for analyzing the captured results is Python with


pylab running
• The IPython notebook provides a very nice environment for
working with the data contained in the log file and creating
post analysis plots
• A few screen shots from the available IPython notebook are
given below
– Note: The signal values held in buffer() correspond to
a 1 kHz sinusoid on the audio codec with f s = 48 ksps

ECE 5655/4655 Real-Time DSP B–5


Appendix B • Using the Keil Debugger Command Line

Make sure the notebook


is pointing to the folder
containing the data file

Compute some
stats

Plot the time


domain signal

B–6 ECE 5655/4655 Real-Time DSP


Creating User Functions

Plot the
frequency
domain as a
1 kHz spectral line as expected scaled version
of
j2πf ⁄ f s
X(e )

• The C-code set-up that fills the array buffer() is summa-


rized below:

Add globals

Fill the buffer and


wrap when full

ECE 5655/4655 Real-Time DSP B–7


Appendix B • Using the Keil Debugger Command Line

B–8 ECE 5655/4655 Real-Time DSP

You might also like