Scribd
Upload
102 views

Lab - 8 Assessment 1 Subnetted IPv4 Configuration V2

Lab_8 Assessment 1

Uploaded by

yawahab
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
102 views

Lab - 8 Assessment 1 Subnetted IPv4 Configuration V2

Lab_8 Assessment 1

Uploaded by

yawahab
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Lab 8 Assessment 1 – Configuring Subnetted IPv4 Addressing

Topology

Addressing Table
Device Interface IP Address Subnet Mask Default Gateway
R1 G0/0 10.16.0.1 255.240.0.0 N/A
G0/1 10.32.0.1 255.240.0.0 N/A
Lo0 10.48.0.1 255.240.0.0 N/A
Lo1 10.64.0.1 255.240.0.0 N/A
S1 VLAN 1 10.47.255.254 255.240.0.0 10.32.0.1
PC-A NIC 10.32.0.2 255.240.0.0 10.32.0.1
PC-B NIC 10.16.0.2 255.240.0.0 10.16.0.1

Objectives
Part 1: Configure the Devices
Part 2: Test and Troubleshoot the Network

Background / Scenario
You will configure the host PCs, switch and router interfaces, including loopback interfaces. The loopback
interfaces are created to simulate additional LANs attached to router R1.
After the network devices and host PCs have been configured, you will use the ping command to test for
network connectivity.

Required Resources
Packet Tracer
Packet Tracer file: Assessment 8.1.pka
Please use only the correct packet tracer file as otherwise the assessment will not be able to be
marked.

© 2020 Cisco and/or its affiliates. All rights reserved Page 1 of 2


Lab - Implementing a Subnetted IPv4 Addressing Scheme

Configure the Devices


In Part 1, set up the network topology and configure settings on the PCs, Switch and router, such as the
router Gigabit Ethernet interface IP addresses, and the PC’s IP addresses, subnet masks, and default
gateways. Refer to the Addressing Table for device names and address information:
a. Fully configure the switch as per the standard configuration steps discussed in previous labs and save the
configuration:
1) Correct device names as per the topology
2) DNS lookup turned off
3) IP address as listed in Addressing Table
4) Configure the default gateway for the Switch
5) Clear text passwords encrypted.
6) cisco as the console and vty passwords with login enabled
7) class as the privileged EXEC password
8) Banner that warns anyone accessing the device that unauthorized access is prohibited. With the
following text:
Unauthorised access is prohibited and will be strictly prosecuted.
9) Save the configuration
b. Configure the router:
Configure the routers as per the standard configuration in previous labs:
1) Assign a device name to the router.
2) Disable DNS lookup to prevent the router from attempting to translate incorrectly entered commands
as though they were host names.
3) Assign class as the privileged EXEC encrypted password.
4) Assign cisco as the console password and enable login.
5) Assign cisco as the VTY password and enable login. Verify the number of vty lines are on the router.
6) Encrypt the clear text passwords.
7) Create a banner that warns anyone accessing the device:
Unauthorised access is prohibited and you will be strictly prosecuted.
8) Assign IPv4 addresses to all interfaces on Router as per the addressing table and enable them.
9) Save the running configuration to the startup configuration.

Step 2: Configure the PC interfaces.


a. Configure the IP address, subnet mask, and default gateway settings on PC-A.
b. Configure the IP address, subnet mask, and default gateway settings on PC-B.

Test and Troubleshoot the Network (Not assessed):

Use appropriate commands to verify the configuration

© 2020 Cisco and/or its affiliates. All rights reserved Page 2 of 2

You might also like