Worldwide

www.grinnell.com
Contacts

Grinnell Grooved Fittings

Ductile Iron and Fabricated Steel
and draining the system. Failure to do
Table of so may result in serious personal injury,
property damage, and/or impaired de-
Contents vice performance.
45° and 90° Elbows . . . . . . . . . . . . . . . 2 It is the designer’s responsibility to se-
11-1/4° Elbows . . . . . . . . . . . . . . . . . . . 4 lect products suitable for the intended
22-1/2° Elbows . . . . . . . . . . . . . . . . . . . 5
service and to ensure that pressure For Fire Protection pressure rating,
listing, and approval information, contact
ratings and performance data are not
3D Long Radius Elbows . . . . . . . . . . . 6 your GRINNELL Representative.
exceeded. Verify material and gas-
5D Long Radius Elbows . . . . . . . . . . . 8
ket selection for compatibility with the
6D Long Radius Elbows . . . . . . . . . . 10
specific application. Always read and
End Caps . . . . . . . . . . . . . . . . . . . . . . 12 understand the installation instructions.
Concentric Reducers . . . . . . . . . . . . 14
Reducing Tees . . . . . . . . . . . . . . . . . . 20 The owner is responsible for maintain-
Cast and Fabricated Tees . . . . . . . . . 26 ing their mechanical system and devic-
Fabricated 45° Laterals . . . . . . . . . . . 27 es in proper operating condition. Con-
Fabricated 45° Reducing Laterals . . 28 tact the installing contractor or device
Eccentric Reducers . . . . . . . . . . . . . . 32 manufacturer with any questions.
Fabricated Tee Wyes . . . . . . . . . . . . . 38 For parts installed in accordance with
Fabricated Reducing Tee Wyes . . . . 42 Bureau Veritas rules and regulations, a
Fabricated Concentric Reducers . . . 44 one-time only field-test is required to Material
Fabricated Adapter Nipples . . . . . . . 46 a maximum working pressure of 1-1/2 • Cast
Cast and Fabricated Crosses . . . . . . 47 times the rated pressure, as per BV NR Ductile iron conforming to
Fabricated Reducing Tees . . . . . . . . 48 467, Pt. C, Ch. 1, Sec. 10, [20.4.2.], ASTM A 536, Grade 65-45-12
Fabricated 90° True Y . . . . . . . . . . . . 53 where applicable. Tests are to be at- Figures: 201, 210, 211, 212, 219, 221,
Fabricated Flange Adapters . . . . . . . 54 tended by a local BV Surveyor. 227, 250, 251, and 260
Fabricated Swaged Nipples . . . . . . . 56 Long Radius Elbows: 201LR and
Fabricated Adapter Nipples . . . . . . . 60
Fabricated 90° Elbow . . . . . . . . . . . . 61
Technical 210LR
Fabricated Tee . . . . . . . . . . . . . . . . . . 61
Fabricated Reducing Base Elbow . . 62
Data • Fabricated Steel
Carbon Steel conforming to
Friction Resistance Table . . . . . . . . . 64 Approvals ASTM A 53, ASTM A 135, and
UL, FM, ULC, VdS, LPCB, BV* ASTM A 795
General *Bureau Veritas (BV) Approval under certifi-
cate number 13377/BO BV applies only to
Figures: 310, 311, 312, 314, 315, 319,
320, 321, 323, 324, 325, 327, 330,
Description Figures 201, 210, 219, 260, 301, 303, 311,
312, 321, 327, 341, and 350.
331, 341, 342, 350, 351, 360, 372,
380, 391, 392, 393, 395, 397, 398,
Grooved fittings provide an economi- 399
NOTICE
cal and efficient method of changing Long Radius Elbows: 301LR and
direction, adding an outlet, reducing, Grooved Fabricated Fittings are UL 310LR, 3D, 5D, and 6D
or capping piping systems. Grooved and ULC Listed and FM Approved
fittings are available in ductile iron or when produced in GRINNELL US Wall Thickness
fabricated steel as indicated. manufacturing facilities. These fittings Sizes 1˝ - 10˝ Schedule 40
can be identified by the agency mark- Sizes 12˝ - 24˝ Standard Wall 0.375
ings on the fittings. VdS Approval and
NOTICE
LPCB Certification are not required for Protective Coatings
The GRINNELL Fittings described fabricated fittings provided they are • Non-lead orange paint
herein must be installed and main- manufactured with pipe meeting the
tained in compliance with this docu- • RAL red (optional) non-lead paint
agency standards.
ment, in addition to the standards of • Hot dipped galvanized conforming
any other authorities having jurisdic- Maximum Working Pressure to ASTM A 153
tion. Failure to do so may result in se- Refer to technical data sheet for cou-
rious personal injury or impair the per- pling pressure rating.
formance of these devices.
Friction Resistance
Never remove any piping component Refer to Table 31 on Page 64.
nor correct or modify any piping defi-
ciencies without first de-pressurizing

Page 1 of 64 APRIL 2014 G180

G180
Page 2 of 64

Figure 201 Figure 210

Nominal Pipe Size Cast 45° Elbow Cast 90° Elbow

ANSI O.D. C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

1-1/4 1.660 1.75 0.9 2.75 1.0

32 42,4 44,5 0,4 69,9 0,5
1-1/2 1.900 1.75 0.9 2.75 1.3
40 48,3 44,5 0,4 69,9 0,6
2 2.375 2.00 1.3 3.25 1.8
C to E 50 60,3 50,8 0,6 82,6 0,8
2-1/2 2.874 2.25 2.1 3.75 3.1
65 73,0 57,2 1,0 95,3 1,4
FIGURE 201 76,1 3.000 2.25 2.2 3.75 3.2
CAST 45° ELBOW 65 76,1 57,2 1,0 95,3 1,5
3 3.500 2.50 3.5 4.25 4.8
80 88,9 63,5 1,6 108,0 2,2
4 4.500 3.000 5.5 5.00 7.5
100 114,3 76,2 2,5 127,0 3,4
139,7 5.500 3.25 7.7 5.50 11.3
125 139,7 82,6 3,5 139,7 5,1
5 5.563 3.25 8.1 5.50 11.6
C to E 125 141,3 82,6 3,7 139,7 5,3

FIGURE 210 165,1 6.500 3.50 11.0 6.50 16.9

CAST 90° ELBOW 150 165,1 88,9 5,0 165,1 7,7
6 6.625 3.50 11.2 6.50 16.6
150 168,3 88,9 5,1 165,1 7,5
8 8.625 4.25 19.0 7.75 29.6
200 219,1 108,0 8,6 196,9 13,4
10 10.750 4.75 28.0 9.00 48.5
250 273,0 120,7 12,7 228,6 22,0
12 12.750 5.250 48.0 10.00 66.4
300 323,9 133,4 22,0 254,0 30,1
TABLE 1
FIGURES 201 AND 210 CAST ELBOWS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS

Figure 301 Figure 310

Nominal Pipe Size Fabricated Fabricated
45° Elbow 90° Elbow
C to E
ANSI O.D. C to E Weight C to E Weight
Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg
FIGURE 301 14 14 5.75 101.8 14 49.5
FABRICATED 45° ELBOW 350 355,6 146,1 46,17 355,6 22,45
16 16 6.625 133.1 16 62.8
400 406,4 168,4 60,37 406,4 28,48
18 18 7.46 168.7 18 80.2
450 457,2 189,5 76,52 457,2 36,37
20 20 8.28 208.4 20 98.9
500 508,0 210,3 94,52 508,0 44,86
24 24 9.94 299 24 144.6
600 609,6 252,5 135,62 609,6 65,58
C to E TABLE 2
FIGURE 310 FIGURES 301 AND 310 FABRICATED ELBOWS
FABRICATED 90° ELBOW NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 3 of 64

Figure 301LR Figure 310LR

Figure 201LR Figure 210LR
Nominal Pipe Size Fabricated Fabricated
Cast 45° Elbow Cast 90° Elbow
45° Elbow 90° Elbow

ANSI O.D. C to E Weight C to E Weight C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg mm kg C to E

1-1/4 1.660 2.50 0.9 3.88 1.1

- - - -
32 42,4 63,5 0,4 98,6 0,5
1-1/2 1.900 2.50 1.0 4.25 1.4
- - - -
40 48,3 63,5 0,5 108,0 0,6
2 2.375 2.75 1.5 4.38 2.4 4.38 2.1
- -
50 60,3 69,9 0,7 111,3 1,1 111,3 0,9 FIGURE 201LR
CAST 45°
2-1/2 2.874 3.00 2.6 5.00 5.1 5.75 3.9 LONG RADIUS ELBOW
- -
65 73,0 76,2 1,2 127,0 2,3 146,0 1,8
76,1mm 3.000 3.00 3.1 5.00 4.4 5.75 2.9
- -
65 76,1 76,2 1,4 127,0 2,0 146,0 1,3
3 3.500 3.38 4.6 5.88 6.6 5.88 6.1
- -
80 88,9 85,9 2,1 149,4 3,0 149,4 2,8 C to E
108,0mm 4.252 4.00 3.7 7.50 6.1
- - - -
100 108,0 101,6 1,7 190,5 2,8
4 4.500 4.00 7.5 7.50 11.6 7.50 11.0
- -
100 114,3 101,6 3,4 191,0 5,3 190,5 4.9
133,0mm 5.250 5.00 6.7 9.50 11.0
- - - -
125 133,0 127,0 3,0 241,3 4.9
FIGURE 301LR
139,7mm 5.500 5.00 12.5 9.50 19.0 9.50 14.3 FABRICATED 45°
- -
125 139,7 127,5 5,7 241,3 8,6 241,3 6,5 LONG RADIUS ELBOW
5 5.563 5.00 12.5 9.50 20.0 9.50 18.7
- -
125 141,3 127,5 5,7 241,3 9,1 241,3 8,5
159,0mm 6.250 5.50 9.9 10.75 16.7
- - - -
150 159,0 139,7 4,5 273,1 7,6
165,1mm 6.500 5.50 12.0 10.75 26.4 10.75 19.2
- -
150 165,1 139,7 5,4 273,1 12,0 273,1 8,7
6 6.625 5.50 12.0 10.75 29.5 10.75 27.3
- -
150 168,3 139,7 5,4 273,1 13,4 273,1 12,4
216,3mm 8.516 7.25 21.8 15.00 38.4
- - - -
200 216,3 184,2 9.9 381,0 17,4 C to E
8 8.625 7.25 34.0 14.25 62.1 15.00 53.8 FIGURE 210LR
- -
200 219,1 184,2 15,4 362,0 28,2 381,0 24,4 CAST 90°
LONG RADIUS ELBOW
267,4mm 10.528 8.50 38.5 18.00 67.9
- - - -
250 267,4 215,9 17,5 457,2 30,8
10 10.750 8.50 56.0 18.00 95.4
- - - -
250 273,0 215,9 25,4 457,2 43,3
318,5mm 12.539 10.00 56.1 21.00 99.1
- - - -
300 318,5 254,0 25.4 533,4 44.9
12 12.750 10.00 98.0 21.00 139.5
- - - -
300 323,9 254,0 44,5 533,4 63,2
14 14.000 8.75 60.0 8.75 97.4 21.00 131.0 21.00 154.1
350 355,6 228,3 27,2 222,3 44,1 533,4 59,4 533,4 69,9
C to E
16 16.000 10.00 97.0 10.00 239.2 24.00 180.0 24.00 201.6
400 406,4 254,0 44,0 254,0 108.4 609,6 81,6 609,6 91,4 FIGURE 310LR
FABRICATED 90°
18 18.000 11.25 303.0 27.00 255.5 LONG RADIUS ELBOW
- - - -
450 457,2 285,8 137,4 685,8 115,9
20 20.000 12.50 414.0 30.00 304.0
- - - -
500 508,0 317,5 187,8 762,0 137,9
24 24.000 15.00 540.0 36.00 453.8
- - - -
600 609,6 381,0 244,9 914,4 205,8
TABLE 3
FIGURES 201LR, 301LR, 210LR, AND 310LR CAST AND FABRICATED LONG RADIUS ELBOWS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 4 of 64

Figure 211 Figure 311

Nominal Pipe Size Cast 11-1/4º Elbow Fabricated 11-1/4º Elbow

ANSI O.D. C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

1-1/4 1.660 1.38 0.7 1.38 0.5

32 42,4 35,1 0,3 35,1 0,2
1-1/2 1.900 1.38 0.8 1.38 0.5
40 48,3 35,1 0,4 35,1 0,2
2 2.375 1.38 1.1 1.38 0.7
50 60,3 35,1 0,5 35,1 0,3
2-1/2 2.874 1.50 1.6 1.50 1.3
65 73,0 38,1 0,7 38,1 0,6
76,1mm 3.000 1.50 1.7 1.50 0.9
65 76,1 38,1 0,7 38,1 0,4
3 3.500 1.50 2.2 1.50 1.7
80 88,9 38,1 1,0 38,1 0,7
108,0mm 4.252 1.75 1.6
- -
100 108,0 44,5 0,7
4 4.500 1.75 3.4 1.75 2.8
C to E 100 114,3 44,5 1,5 44,5 1,3
133,0mm 5.250 2.00 2.5
- -
125 159,0 50,8 1,1
139,7mm 5.500 2.00 5.1 2.00 3.3
125 139,7 50,8 2,3 50,8 1,5
FIGURE 211
CAST 11-1/4° ELBOW 5 5.563 2.00 5.2 2.00 4.4
125 141,3 50,8 2,4 50.8 2,0
159,0mm 6.250 2.00 3.4
- -
150 159,0 50,8 1,5
C to E 165,1mm 6.500 2.00 6.4 2.00 4.0
150 165,1 50.8 2,9 50,8 1,8
6 6.625 2.00 6.5 2.00 5.7
150 168,3 50.8 2,9 50,8 2,6
216,3mm 8.516 2.00 6.0
- -
200 216,3 50,8 2,7
FIGURE 311
FABRICATED 11-1/4° ELBOW 8 8.625 2.00 9.2 2.00 8.6
(SEGMENT WELDED) 200 219,1 50,8 4,2 50,8 4,0
267,4mm 10.528 2.13 9.2
- -
250 267,4 54,1 4,2
10 10.750 2.13 13.2
- -
250 273,0 54,1 6,0
318,5mm 12.539 2.25 12.2
- -
300 318,5 57,2 5,5
12 12.750 2.25 17.0
- -
300 323,9 57,2 7,7
14 14.000 3.500 30.1
- -
350 355,6 88,9 13,7
16 16.000 4.00 39.7
- -
400 406,4 101,6 18,0
18 18.000 4.50 50.7
- -
450 457,2 114,3 23,0
20 20.00 5.00 63.0
- -
500 508,0 127,0 28,6
24 24.000 6.00 91.2
- -
600 609,6 152,4 41.4
TABLE 4
FIGURES 211 AND 311 CAST AND FABRICATED ELBOWS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 5 of 64

Figure 212 Figure 312

Nominal Pipe Size Cast 221/2º Elbow Fabricated 221/2º Elbow

ANSI O.D. C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

1-1/4 1.660 1.75 0.8 1.75 0.7

32 42,4 44,5 0,4 44,5 0,3
1-1/2 1.900 1.75 1.0 1.75 0.7
40 48,3 44,5 0,5 44,5 0,3
2 2.375 1.88 1.3 1.88 1.1
50 60,3 47,8 0,6 47,8 0,5
2-1/2 2.874 2.00 1.9 2.00 1.8
65 73,0 50,8 0,9 50,8 0,8
76,1mm 3.000 2.00 2.0 2.00 1.3
65 76,1 50,8 0,9 50,8 0,6
3 3.500 2.25 2.9 2.25 2.7
80 88,9 57,2 1,3 57,2 1,2
108,0mm 4.252 2.63 2.5
- -
100 108,0 66,8 1,1
C to E
4 4.500 2.63 4.7 2.63 4.5
100 114,3 66,8 2,1 66,8 2,0
133,0mm 5.250 2.88 3.8
- -
125 159,0 73,2 1,7
139,7mm 5.500 2.88 6.9 2.88 5.1
125 139,7 73,2 3,1 73,2 2,3
FIGURE 212
5 5.563 2.88 6.9 2.88 6.7 CAST 22-1/2° ELBOW
125 141,3 73,2 3,1 73,2 3,0
159,0mm 6.250 3.13 5.9
- -
150 159,0 79.5 2,7 C to E
165,1mm 6.500 3.13 6.6
- -
150 165,1 79,5 3,0
6 6.625 3.13 9.4 3.13 9.5
150 168,3 79,5 4,3 79,5 4,3
216,3mm 8.516 3.88 12.4
- -
200 216,3 98,6 5,6
FIGURE 312
8 8.625 3.88 17.0 3.88 17.8 FABRICATED 22-1/2° ELBOW
200 219,1 98,6 7,7 98,6 8,1 (SEGMENT WELDED)
267,4mm 10.528 4.38 20.0
- -
250 267,4 111,3 9,1
10 10.750 4.38 28.7
- -
250 273,0 111,3 13,0
318,5mm 12.539 4.88 27.8
- -
300 318,5 124,0 12,6
12 12.750 4.88 39.1
- -
300 323,9 124,0 17,7
14 14.000 5.00 44.1
- -
350 355,6 127,0 20,0
16 16.000 5.00 50.6
- -
400 406,4 127,0 23
18 18.000 5.50 63.0
- -
450 457,2 139,7 28,6
20 20.000 6.00 76.4
- -
500 508,0 152,4 34,7
24 24.000 7.00 106.9
- -
600 609,6 177.8 48,5
TABLE 5
FIGURES 212 AND 312 CAST AND FABRICATED ELBOWS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 6 of 64

C to E C to E
C to E
C to E
C to E C to E

R = 3D R = 3D R = 3D R = 3D R = 3D R = 3D
FIGURE 310-3D FIGURE 306-3D FIGURE 301-3D FIGURE 303-3D FIGURE 312-3D FIGURE 311-3D
(90°) (60°) (45°) (30°) (22.5°) (11.25°)

Figure 310-3D Figure 306-3D Figure 301-3D Figure 303-3D Figure 312-3D Figure 311-3D
Nominal Pipe Size 90º Elbow 60º Elbow 45º Elbow 30º Elbow 22-1/2º Elbow 11-1/4º Elbow

ANSI OD C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg mm kg mm kg mm kg

2 2.375 10.00 5.3 7.50 4.7 6.50 4.2 5.75 3.8 5.25 3.5 4.50 2.9
50 60,3 254,0 2,4 191,0 2,1 165,0 1,9 146,0 1,7 133,0 1,6 114,0 1,3
2-1/2 2.874 11.50 9.5 8.25 8.2 7.25 7.6 6.00 6.4 5.50 5.8 4.75 4.9
65 73,0 292,0 4,3 210,0 3,7 184,0 3,4 152,0 2,9 140,0 2,6 121,0 2,2
76,1mm 3.000 11.50 9.7 8.25 8.6 7.25 8.2 6.00 6.9 5.50 6.2 4.75 5.7
65 76,1 292,0 4,4 210,0 3,9 184,0 3,7 152,0 3,1 140,0 2,8 121,0 2,6
3 3.500 13.00 14.7 9.25 12.6 7.75 11.2 6.50 9.7 5.75 8.5 5.00 7.3
80 88,9 330,0 6,7 235,0 5,7 197,0 5,1 165,0 4,4 146,0 3,9 127,0 3,3
3-1/2 4.000 10.00 14.4
- - - - - - - - - -
90 101,6 254,0 6,5
4 4.500 16.00 24.1 11.00 20.4 9.00 17.8 7.25 14.8 6.50 13.4 5.25 10.5
100 114,3 406,0 10,9 279,0 9,3 229,0 8,1 184,0 6,7 165,0 6,1 133,0 4,8
108,0mm 4.252 16.00 39.7 11.00 19.2 9.00 16.9 7.25 13.2 6.50 12.6 5.25 9.7
100 108,0 406,0 18,0 279,0 8,7 229,0 7,6 184,0 6,0 165,0 5,7 133,0 4,4
5 5.563 20.00 40.9 13.75 34.5 11.25 30.1 9.00 24.9 8.00 22.2 6.50 17.6
125 141,3 508,0 18,6 349,0 15,7 286,0 13,7 229,0 11,3 203,0 10,1 165,0 8,0
133,0mm 5.250 20.00 39.9 13.75 32.4 11.25 28.5 9.00 22.8 8.00 20.5 6.50 16.2
125 133,0 508,0 18,1 349,0 14,7 286,0 12,9 229,0 10,3 203,0 19,3 165,0 7,3
139,7mm 5.500 20.00 40.1 13.75 33.2 11.25 29.1 9.00 23.6 8.00 21.8 6.50 16.8
125 139,7 508,0 18,2 349,0 15,1 286,0 13,2 229,0 10,7 203,0 9,8 165,0 7,6
6 6.625 24.00 63.7 16.50 53.7 13.50 46.9 10.75 38.6 9.50 34.2 7.75 27.1
150 168,3 610,0 28,9 419,0 24,4 343,0 21,3 273,0 17,5 241,0 15,5 197,0 12,3
159,0mm 6.250 24.00 62.2 16.50 49.8 13.50 45.8 10.75 36.8 9.50 32.6 7.75 25.7
150 159,0 610,0 28,2 419,0 22,6 343,0 20,8 273,0 16.7 241,0 14,8 197,0 11,7
165,1mm 6.500 24.00 62.8 16.50 52.5 13.50 46.2 10.75 37.2 9.50 33.8 7.75 26.8
150 165,1 610,0 28,5 419,0 23,8 343,0 21,0 273,0 16,9 241,0 15,3 197,0 12,2
8 8.625 32.00 128.0 22.00 108.0 18.00 94.3 14.50 78.7 12.75 69.3 10.50 55.7
200 219,1 813,0 58,1 559,0 49,0 457,0 42,8 368,0 35,7 324,0 31,4 267,0 25,3
216,3mm 8.516 32.00 127 22.00 107.5 18.00 93.1 14.50 77.6 12.75 68.4 10.50 54.9
200 216,3 813,0 57,6 559,0 48,8 457,0 42,2 368,0 35.2 324,0 31,0 267,0 24,9
10 10.750 40.00 226.4 27.25 189.4 22.50 166.9 18.00 138.2 16.00 123.2 13.00 97.3
250 273,0 1016,0 102,7 692,0 85,9 572,0 75,7 457,0 62,7 406,0 55,9 330,0 44,1
267,4mm 10.528 40.00 225 27.25 187.2 22.50 165.2 18.00 137.8 16.00 122.7 13.00 96.6
250 267,4 1016,0 102,1 692,0 84,9 572,0 74,9 457,0 62,5 406,0 55,7 330,0 43,8
12 12.750 48.00 332.9 32.75 278.8 27.00 245.3 21.75 204.7 19.25 181.6 15.51 141.8
300 323,9 1219,0 151,0 832,0 126,5 686,0 111,3 552,0 92,9 489,0 82,4 394,0 64,3
318,5mm 12.539 48.00 330 32.75 275.4 27.00 243.9 21.75 202.8 19.25 180.1 15.50 139.7
300 318,5 1219,0 149,7 832,0 124,9 686,0 110,6 552,0 92,0 489,0 81,7 394,0 63,4
TABLE 6 (1 OF 2)
3D LONG RADIUS ELBOWS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 7 of 64

C to E C to E
C to E
C to E
C to E C to E

R = 3D R = 3D R = 3D R = 3D R = 3D R = 3D
FIGURE 310-3D FIGURE 306-3D FIGURE 301-3D FIGURE 303-3D FIGURE 312-3D FIGURE 311-3D
(90°) (60°) (45°) (30°) (22.5°) (11.25°)

Figure 310-3D Figure 306-3D Figure 301-3D Figure 303-3D Figure 312-3D Figure 311-3D
Nominal Pipe Size 90º Elbow 60º Elbow 45º Elbow 30º Elbow 22-1/2º Elbow 11-1/4º Elbow

ANSI OD C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg mm kg mm kg mm kg

14 14.000 56.00 427.6 38.25 358.5 31.50 315.0 25.25 261.4 22.50 233.7 18.25 184.4
350 355,6 1422,0 194,0 972,0 162,6 800,0 142,9 641,0 118,6 572,0 106,0 464,0 83,6
16 16.000 64.00 560.3 43.75 470.1 36.00 412.8 29.00 334.5 25.50 303.2 20.75 239.9
400 406,4 1626,0 254,1 1111,0 213,2 914,0 187,2 737,0 151,7 648,0 137,5 527,0 108,8
18 18.000 72.00 710.7 49.25 596.9 40.50 523.7 32.50 435.1 28.75 385.7 23.35 304.5
450 457,2 1829,0 322,4 1251,0 270,7 1029,0 237,5 826,0 197,4 730,0 175,0 593,0 138,1
20 20.000 80.00 879.3 54.75 738.7 45.00 647.8 36.00 536.4 32.00 478.1 26.00 377.7
500 508,0 2032,0 398,8 1391,0 335,1 1143,0 293.8 914,0 243,3 813,0 216,9 660,0 171,3
24 24.000 96.00 1270.3 65.50 1,063.6 53.75 931.0 43.25 775.7 38.25 687.2 31.00 540.9
600 609,6 2438,0 576,2 1664,0 482,4 1365,0 422,3 1099,0 351,9 972,0 311,8 787,0 245,3
Notes:
1. Sizes up to and including 4˝ are provided with 4˝ (101,6 mm) long integral tangent
2. Remaining sizes provided with integral tangents with lengths equal to Nominal Pipe Size
3. C to E tolerances: 2˝ through 6˝ ± 1/8˝ (3,2 mm); 8˝ through 16˝ ± 1/4˝ (6,4 mm); 18˝ through 24˝ ± 3/8˝ (9,5 mm)

TABLE 6 (2 OF 2)
3D LONG RADIUS ELBOWS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 8 of 64

C to E C to E
C to E
C to E
C to E C to E

R = 5D R = 5D R = 5D R = 5D R = 5D R = 5D
FIGURE 310-5D FIGURE 306-5D FIGURE 301-5D FIGURE 303-5D FIGURE 312-5D FIGURE 311-5D
(90°) (60°) (45°) (30°) (22.5°) (11.25°)

Figure 310-5D Figure 306-5D Figure 301-5D Figure 303-5D Figure 312-5D Figure 311-5D
Nominal Pipe Size 90º Elbow 60º Elbow 45º Elbow 30º Elbow 22-1/2º Elbow 11-1/4º Elbow

ANSI OD C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg mm kg mm kg mm kg

2 2.375 14.00 7.2 9.75 6.1 8.25 5.5 6.75 4.6 6.00 4.1 5.00 3.3
50 60,3 356,0 3,3 248,0 2,8 210,0 2,5 171,0 2,1 152,0 1,9 127,0 1,5
2-1/2 2.874 16.50 13.3 11.25 11.2 9.25 9.8 7.50 8.3 6.50 7.2 5.25 5.6
65 73,0 419,0 6,0 286,0 5,1 235,0 4,4 191,0 3,8 165,0 3,3 133,0 2,5
76,1mm 3.000 16.50 14.3 11.25 11.8 9.25 10.2 7.50 9.4 6.50 7.9 5.25 6.6
65 76,1 419,0 6,5 286,0 5,4 235,0 4,6 191,0 4,3 165,0 3,6 133,0 3,0
3 3.500 19.00 21.0 12.75 17.5 10.25 15.1 8.00 12.3 7.00 10.8 5.51 8.3
80 88,9 483,0 9,5 324,0 7,9 260,0 6,8 203,0 5,6 178,0 4,9 140,0 3,8
3-1/2 4.000 12.25 20.0
- - - - - - - - - -
90 101,6 311,0 9,1
4 4.500 24.00 35.4 15.50 28.9 12.50 25.4 9.50 20.1 8.00 17.1 6.00 12.5
100 114,3 610,0 16,1 394,0 13,1 318,0 11,5 241,0 9,1 203,0 7,8 152,0 5,7
108,0mm 4.252 24.00 34.6 15.50 28.1 12.50 24.6 9.50 19.8 8.00 16.4 6.00 11.7
100 108,0 610,0 15,7 394,0 12,7 318,0 11,2 241,0 9,0 203,0 7,4 152,0 5,3
5 5.563 30.00 60.0 19.50 49.2 15.50 42.3 11.75 33.7 10.00 28.9 7.51 21.2
125 141,3 762,0 27,2 495,0 22,3 394,0 19,2 298,0 15,3 254,0 13,1 191,0 9,6
133,0mm 5.250 30.00 58.7 19.50 48.0 15.50 41.1 11.75 32.5 10.00 27.0 7.25 19.8
125 133,0 762,0 26,6 495,0 21,7 394,0 18,6 298,0 14,7 254,0 12,2 191,0 8,9
139,7mm 5.500 30.00 59.3 19.50 48.5 15.50 41.6 11.75 33.0 10.00 28.2 7.25 20.5
125 139,7 762,0 26,9 495,0 22,0 394,0 18,9 298,0 15,0 254,0 12,8 191,0 9,3
6 6.625 36.00 93.5 23.25 76.1 18.50 65.5 14.00 52.7 12.00 45.0 9.02 32.9
150 168,3 914,0 42,4 591,0 34,5 470,0 29,7 356,0 23,9 305,0 20,4 229,0 14,9
159,0mm 6.250 36.00 92.0 23.25 74.7 18.50 64.1 14.00 51.4 12.00 43.6 9.00 31.5
150 159,0 914,0 41,7 591,0 33,8 470,0 29,1 356,0 23,3 305,0 19,7 229,0 14,3
165,1mm 6.500 36.00 92.8 23.25 75.4 18.50 64.8 14.00 52.0 12.00 44.3 6.00 32.2
150 165,1 914,0 42,1 591,0 34,2 470,0 29,4 356,0 23,6 305,0 20,1 229,0 14,6
8 8.625 48.00 187.9 31.00 152.9 24.50 130.8 18.75 105.2 16.00 90.5 12.00 66.2
200 219,1 1219,0 85,2 787,0 69,4 622,0 59,3 476,0 47,7 406,0 41,1 305,0 30,0
216,3mm 8.516 48.00 187.2 31.00 152.2 24.50 130.1 18.75 104.5 16.00 89.8 12.00 65.5
200 216,3 1219,0 84,9 787,0 69,0 622,0 59,0 476,0 47,4 406,0 40,7 305,0 29,7
10 10.750 60.00 332.6 39.00 272.5 30.75 232.5 23.50 186.8 20.00 160.3 15.00 117.2
250 273,0 1524,0 150,9 991,0 123,6 781,0 105,5 597,0 84,7 508,0 72,7 381,0 53,2
267,4mm 10.528 60.00 331.7 39.00 271.6 30.75 231.6 23.50 185.7 20.00 159.4 15.00 116.3
250 267,4 1524,0 150,5 991,0 123,2 781,0 105,1 597,0 84,2 508,0 72,3 381,0 52,8
12 12.750 72.00 488.8 46.75 400.0 37.00 342.7 28.00 272.3 24.00 235.5 18.00 172.2
300 323,9 1829,0 221,7 1187,0 181,4 940,0 155,4 711,0 123,5 610,0 106,8 457,0 78,1
318,5mm 12.539 72.00 487.5 46.75 398.5 37.00 340.9 28.00 270.1 24.00 233.8 18.00 170.1
300 318,5 1929,0 221,1 1187,0 180,8 940,0 154,6 711,0 122,6 610,0 106,0 457,0 77,2
TABLE 7 (1 OF 2)
5D LONG RADIUS ELBOWS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 9 of 64

C to E C to E
C to E
C to E
C to E C to E

R = 5D R = 5D R = 5D R = 5D R = 5D R = 5D
FIGURE 310-5D FIGURE 306-5D FIGURE 301-5D FIGURE 303-5D FIGURE 312-5D FIGURE 311-5D
(90°) (60°) (45°) (30°) (22.5°) (11.25°)

Figure 310-5D Figure 306-5D Figure 301-5D Figure 303-5D Figure 312-5D Figure 311-5D
Nominal Pipe Size 90º Elbow 60º Elbow 45º Elbow 30º Elbow 22-1/2º Elbow 11-1/4º Elbow

ANSI OD C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg mm kg mm kg mm kg

14 14.000 84.00 627.7 54.50 513.3 43.00 438.3 32.75 350.7 28.00 302.5 21.00 221.2
350 355,6 2134,0 284,7 1384,0 232,8 1092,0 198,8 832,0 159,1 711,0 137,2 533,0 100,3
16 16.000 96.00 822.5 62.25 672.2 49.25 575.6 37.50 460.6 32.00 396.4 24.00 289.8
400 406,4 2436,0 373,1 1581,0 304,9 1251,0 261,1 953,0 208,9 813,0 179,8 610,0 131,5
18 18.000 108.00 1,043.5 70.00 852.5 55.25 728.2 42.25 585.3 36.00 506.9 27.00 367.8
450 457,2 2743,0 473,3 1778,0 386,7 1403,0 330,3 1073,0 265,5 914,0 229,9 686,0 166,8
20 20.000 120.00 1,290.9 77.75 1,054.2 61.50 902.5 46.75 720.7 40.00 622.1 30.00 454.9
500 508,0 3048,0 585,5 1975,0 478,2 1562,0 409,4 1187,0 326,9 1016,0 282,2 762,0 206,3
24 24.000 144.00 1,864.4 93.25 1,521.8 73.75 1,302.5 56.25 1,044.0 48.00 898.5 35.75 651.2
600 609,6 3658,0 845,7 2369,0 690,3 1873,0 590,8 1429,0 473,6 1219,0 407,6 908,0 295,4
Notes:
1. Sizes up to and including 4˝ are provided with 4˝ (101,6 mm) long integral tangent
2. Remaining sizes provided with integral tangents with lengths equal to Nominal Pipe Size
3. C to E tolerances: 2˝ through 6˝ ± 1/8˝ (3,2 mm); 8˝ through 16˝ ± 1/4˝ (6,4 mm); 18˝ through 24˝ ± 3/8˝ (9,5 mm)

TABLE 7 (2 OF 2)
5D LONG RADIUS ELBOWS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 10 of 64

C to E C to E
C to E
C to E
C to E C to E

R = 6D R = 6D R = 6D R = 6D R = 6D R = 6D
FIGURE 310-6D FIGURE 306-6D FIGURE 301-6D FIGURE 303-6D FIGURE 312-6D FIGURE 311-6D
(90°) (60°) (45°) (30°) (22.5°) (11.25°)

Figure 310-5D Figure 306-5D Figure 301-5D Figure 303-5D Figure 312-5D Figure 311-5D
Nominal Pipe Size 90º Elbow 60º Elbow 45º Elbow 30º Elbow 22-1/2º Elbow 11-1/4º Elbow

ANSI OD C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg mm kg mm kg mm kg

2 2.375 16.00 8.2 11.00 6.9 9.00 6.0 7.25 5.0 6.50 4.5 5.25 3.6
50 60,3 406,0 3,7 279,0 3,1 229,0 2,7 18,04 2,3 165,0 2,0 133,0 1,6
2-1/2 2.874 19.00 13.0 12.75 12.7 10.25 11.0 8.00 8.9 7.00 7.8 5.51 6.0
65 73,0 483,0 5,9 324,0 5,8 260,0 5,0 203,0 4,0 178,0 3,5 140,0 2,7
76,1mm 3.000 19.00 12.2 12.75 19.9 10.25 10.2 8.00 8.1 7.00 7.0 5.50 5.3
65 76,1 483,0 5,5 324,0 9,0 260,0 4,6 203,0 3,7 178,0 3,2 140,0 2,4
3 3.500 22.00 24.1 14.50 19.9 11.50 17.1 8.75 13.6 7.50 11.7 5.75 8.7
80 88,9 559,0 10,9 368,0 9,0 292,0 7,8 222,0 6,2 191,0 5,3 146,0 3,9
3-1/2 4.000 16.25 22.8
- - - - - - - - - -
90 101,6 413,0 10,3
4 4.500 28.00 41.1 18.00 33.6 14.00 28.4 10.50 22.5 8.75 18.9 6.50 13.8
100 114,3 711,0 18,6 457,0 15,2 356,0 12,9 267,0 10,2 222,0 8,6 165,0 6,3
108,0mm 4.252 28.00 40.0 18.00 32.5 14.00 27.3 10.50 21.4 8.75 17.8 6.50 12.7
100 108,0 711,0 18,1 457,0 14,7 356,0 12,4 267,0 9,7 222,0 8,1 165,0 5,8
5 5.563 35.00 69.6 22.25 56.2 17.50 48.1 13.00 37.7 11.00 32.3 8.00 22.9
125 141,3 889,0 31,6 565,0 25,5 445,0 21,8 330,0 17,1 279,0 14,7 203,0 10,4
133,0mm 5.250 35.00 68.4 22.25 55.0 17.50 46.9 13.00 36.6 11.00 31.2 8.00 21.7
125 133,0 889,0 31.0 565,0 24,9 445,0 21,3 330,0 16,6 279,0 14,2 203,0 9,8
139,7mm 5.500 35.00 69.0 22.25 55.6 17.50 47.6 13.00 37.1 11.00 31.7 8.00 22.7
125 139,7 889,0 31,3 565,0 25,2 445,0 21,6 330,0 16,8 279,0 14,4 203,0 10,3
6 6.625 42.00 108.4 26.75 87.7 21.00 74.8 15.75 59.3 13.25 50.5 9.50 35.3
150 168,3 1067,0 49,2 679,0 39,8 533,0 33,9 400,0 26,9 337,0 22,9 241,0 16,0
159,0mm 6.250 42.00 105.7 26.75 86.0 21.00 73.0 15.75 57.5 13.25 48.5 9.50 33.1
150 159,0 1067,0 47,9 679,0 39.0 533,0 33,1 400,0 26,1 337,0 22,0 241,0 15,0
165,1mm 6.500 42.00 106.2 26.75 86.5 21.00 73.5 15.75 58.0 13.25 49.0 9.50 33.7
150 165.1 1067,0 48,2 679,0 39,2 533,0 33,3 400,0 26,3 337,0 22,2 241,0 15,3
8 8.625 56.00 217.8 35.75 176.7 28.00 150.4 21.00 119.2 17.50 100.4 12.75 71.5
200 219,1 1422,0 98,8 908,0 80,1 711,0 68,2 533,0 54,1 445,0 45,5 324,0 32,4
216,3mm 8.516 45.00 216.2 35.75 175.5 28.00 149.2 21.00 118.0 17.50 98.6 12.75 70.2
200 216,3 1422,0 98,1 908,0 79,6 711,0 67,7 533,0 53,5 445,0 44,7 324,0 31,8
10 10.750 70.00 385.6 44.75 313.1 35.00 266.3 26.00 208.9 22.00 178.8 16.00 127.1
250 273,0 1778,0 174,9 1137,0 142,0 889,0 120,8 660,0 94,8 559,0 81,1 406,0 57,7
267,4mm 10.528 70.00 384.8 44.75 312.3 35.00 265.5 26.00 208.1 22.00 178.1 16.00 126.2
250 267,4 1778,0 174,5 1137,0 141,6 889,0 120,4 660,0 94,4 559,0 80,8 406,0 57,2
12 12.750 84.00 566.7 53.50 458.5 41.75 388.9 31.25 307.5 26.25 261.1 19.00 184.4
300 323,9 2134,0 257,1 1359,0 208,0 1060,0 176,4 794,0 139,5 667,0 118,4 483,0 83,6
318,5mm 12.539 84.00 565.5 53.50 457.0 41.75 387.4 31.25 306.0 26.25 259.6 19.00 183.0
300 318,5 2134,0 256,5 1359,0 207,3 1060,0 175,7 794,0 138,8 667,0 117,8 483,0 83.0
TABLE 8 (1 OF 2)
6D LONG RADIUS ELBOWS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 11 of 64

C to E C to E
C to E
C to E
C to E C to E

R = 6D R = 6D R = 6D R = 6D R = 6D R = 6D
FIGURE 310-6D FIGURE 306-6D FIGURE 301-6D FIGURE 303-6D FIGURE 312-6D FIGURE 311-6D
(90°) (60°) (45°) (30°) (22.5°) (11.25°)

Figure 310-5D Figure 306-5D Figure 301-5D Figure 303-5D Figure 312-5D Figure 311-5D
Nominal Pipe Size 90º Elbow 60º Elbow 45º Elbow 30º Elbow 22-1/2º Elbow 11-1/4º Elbow

ANSI OD C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg mm kg mm kg mm kg

14 14.000 98.00 727.8 62.50 589.6 48.75 499.9 36.50 395.4 30.75 336.9 22.25 238.0
350 355,6 2489,0 330,1 1588,0 267,4 1238,0 226,8 927,0 179,4 781,0 152,8 565,0 108,0
16 16.000 112.00 953.6 71.50 773.3 55.75 655.5 41.75 518.6 35.25 443.0 25.51 312.9
400 406,4 2845,0 432,5 1816,0 350,8 1416,0 297,3 1060,0 235,2 895,0 200,9 648,0 141,9
18 18.000 126.00 1,209.9 80.50 981.9 62.75 832.7 47.00 658.5 39.50 559.5 28.75 398.7
450 457,2 3200,0 548,8 2045,0 445,4 1594,0 377,7 1194,0 298,7 1003,0 253,8 730,0 180,8
20 20.000 140.00 1,496.6 89.25 1,212.0 69.75 1,029.8 52.25 815.0 44.00 694.1 31.75 488.7
500 508,0 3556,0 678,8 2267,0 549,8 1772,0 467,1 1327,0 369,7 1118,0 314,8 806,0 221,7
24 24.000 168.00 2,161.6 107.25 1,752.9 83.75 1,488.2 62.50 1,173.0 52.34 992.5 38.25 709.3
600 609,6 4267,0 980,5 2724,0 795,1 2127,0 675,0 1588,0 532,1 1329,0 450,2 972,0 321,7
Notes:
1. Sizes up to and including 4˝ are provided with 4˝ (101,6 mm) long integral tangent
2. Remaining sizes provided with integral tangents with lengths equal to Nominal Pipe Size
3. C to E tolerances: 2˝ through 6˝ ± 1/8˝ (3,2 mm); 8˝ through 16˝ ± 1/4˝ (6,4 mm); 18˝ through 24˝ ± 3/8˝ (9,5 mm)

TABLE 8 (2 OF 2)
6D LONG RADIUS ELBOWS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 12 of 64

Nominal Pipe Size

E to E A B Weight
Inches Available Inches Lbs.
ANSI O.D. mm NPT Sizes mm kg
Inches Inches
DN mm

1 1.315 0.83 0.2

- -
25 33,4 21,1 0,1
1-1/4 1.660 0.83 On 0.3
1/2˝
32 42,4 21,1 C to E 0,1
1-1/2 1.900 0.83 On 0.4
1/2˝
40 48,3 21,1 C to E 0,2
2 2.375 0.92 0.50 0.7
1/2˝, 3/4˝
50 60,3 23,4 12,7 0,3
E to E
2-1/2 2.874 0.92 0.69 1.0
1/2˝, 3/4˝
65 73,0 23,4 17,5 0,5
76,1mm 3.000 0.86 0.69 1.3
1/2˝, 3/4˝
B 65 76,1 21,8 17,5 0,6
A 3 3.500 0.92 0.94 1.4
1/2˝, 3/4˝,1˝
80 88,9 23,4 23,9 0,6
4 4.500 1.00 1.44 2.6
1/2˝, 3/4˝,1˝
100 114,3 25,4 36,6 1,2
139,7mm 5.500 0.92 1.44 4.7
1/2˝, 3/4˝,1˝
125 139,7 23,4 36,6 2,1
5 5.563 1.00 1.94 5.0
1/2˝, 3/4˝,1˝
125 141,3 25,4 49,3 2,3
165,1mm 6.500 0.92 1.94 6.4
1/2˝, 3/4˝,1˝
150 165,1 23,4 49,3 2,9
6 6.625 1.00 2.50 6.2
1/2˝, 3/4˝,1˝
150 168,3 25,4 63,5 2,8
8 8.625 1.06 3.44 7.1
1/2˝, 3/4˝,1˝
200 219,1 27,0 87,4 3,2
10 10.750 1.02 4.50 24.5
1/2˝, 3/4˝,1˝
250 273,0 25,8 114,3 11,1
12 12.750 1.02 5.44 31.0
1/2˝, 3/4˝,1˝
300 323,9 25,8 138,2 14,1
TABLE 9
FIGURE 260 CAST END CAPS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 13 of 64

Nominal Pipe Size

E to E Weight
Inches Lbs.
ANSI O.D. mm kg
Inches Inches
DN mm

1 1.315 0.83 -
25 33,4 21,1
1-1/4 1.660 1.57 0.3
32 42,4 40,0 0,1
1-1/2 1.900 1.57 0.3
40 48,3 40,0 0,1
2 2.375 1.57 0.5
50 60,3 40,0 0,2
2-1/2 2.874 1.57 0.8
65 73,0 40,0 0,4
76,1mm 3.000 1.57 0.6
65 76,1 40,0 0,3
3 3.500 1.97 1.3
80 88,9 50,0 0,6
4 4.500 2.56 2.3
100 114,3 65,0 1,0
108,0mm 4.252 2.56 1.2
100 108,0 65,0 0,5
5 5.563 3.15 3.7
125 141,3 80,0 1,7
E to E
133,0mm 5.250 3.15 2.2
125 133,0 80,0 0,9
139,7mm 5.500 3.15 2.9
125 139,7 80,0 1,3
6 6.625 3.50 5.4
150 168,3 89,0 2,4
159,0mm 6.250 3.50 3.2
150 159,0 89,0 1,5
165,1mm 6.500 3.50 3.8
150 165,1 89,0 1,7
8 8.625 3.94 9.3
200 219,1 100,0 4,2
216,3mm 8.516 3.94 6.6
200 216,3 100,0 3,0
10 10.750 4.92 16.2
250 273,0 125,0 7,3
267,4mm 10.528 4.92 14.9
250 267,4 125,0 6,8
12 12.750 5.90 -
300 323,9 150,0
318,5mm 12.539 5.90 -
300 318,5 150,0
14 14.000 8.50 36.5
350 355,6 215,9 16,6
16 16.000 9.00 43.5
400 406,4 228,6 19,7
18 18.000 10.00 57.0
450 457,2 254,0 25,6
20 20.000 11.00 75.7
500 508,0 279,4 34,3
24 24.000 12.50 101.0
600 609,6 317,5 45,8
TABLE 10
FIGURE 360 FABRICATED END CAPS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 14 of 64

Figure 250 Figure 350

Nominal Pipe Size Cast Concentric Fabricated Concentric
Reducer Reducer

O.D. E to E Weight E to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

1-1/4 x 1 1.660 x 1.315 2.50 0.7 2.50 0.4

32 x 25 42,4 x 33,4 63,5 0,3 63,5 0.2
1-1/2 x 1 1.900 x 1.315 2.50 0.5
- -
40 x 25 48,3 x 33,4 63,5 0,2
1-1/2 x 1-1/4 1.900 x 1.660 2.50 0.8 2.50 0.5
40 x 32 48,3 x 42,4 63,5 0,3 63,5 0,2
2x1 2.375 x 1.315 2.50 0.6
- -
50 x 25 60,3 x 33,4 63,5 0,4
2 x 1-1/4 2.375 x 1.660 2.50 0.6
- -
50 x 32 60,3 x 42,4 63,5 0,4
2 x 1-1/2 2.375 x 1.900 2.50 0.6
- -
50 x 40 60,3 x 48,3 63,5 0,4
E to E 2-1/2 x 1 2.874 x 1.315 2.50 0.6
- -
65 x 25 73,0 x 33,4 63,5 0,4
2-1/2 x 1-1/4 2.874 x 1.660 2.50 1.4 2.50 0.7
65 x 32 73,0 x 42,4 63,5 0,6 63,5 0,3
2-1/2 x 1-1/2 2.874 x 1.900 2.50 1.4 2.50 0.7
65 x 40 73,0 x 48,3 63,5 0,6 63,5 0,3
FIGURE 250
CAST CONCENTRIC 2-1/2 x 2 2.874 x 2.375 2.50 1.3 2.50 0.8
REDUCER 65 x 50 73,0 x 60,3 63,5 0,6 63,5 0,4
76,1mm x 1 3.000 x 1.315 2.50 0.9
- -
65 x 25 76,1 x 33,4 63,5 0,4
E to E 76,1mm x 1-1/4 3.000 x 1.660 2.50 1.4 2.50 0.9
65 x 32 76,1 x 42,4 63,5 0,6 63,5 0,4
76,1mm x 1-1/2 3.000 x 1.900 2.50 1.4 2.50 1.0
65 x 40 76,1 x 48,3 63,5 0,6 63,5 0,5
76,1mm x 2 3.000 x 2.375 2.50 1.5 2.50 1.0
65 x 50 76,1 x 60,3 63,5 0,7 63,5 0,5
FIGURE 350
FABRICATED CONCENTRIC 3x1 3.500 x 1.315 2.50 1.3
REDUCER - -
80 x 25 88,9 x 33,4 63,5 0,6
3 x 1-1/4 3.500 x 1.660 2.50 1.3
- -
80 x 32 88,9 x 42,4 63,5 0,6
3 x 1-1/2 3.500 x 1.900 2.50 1.8 2.50 1.3
80 x 40 88,9 x 48,3 63,5 0,8 63,5 0,6
3x2 3.500 x 2.375 2.50 1.7 2.50 1.3
80 x 50 88,9 x 60,3 63,5 0,8 63,5 0,6
3 x 2-1/2 3.500 x 2.874 2.50 1.7 2.50 1.3
80 x 65 88,9 x 70,3 63,5 0,8 63,5 0,6
3 x 76,1mm 3.500 x 3.000 2.50 2.0 2.50 1.4
80 x 65 88,9 x 76,1 63,5 0,9 63,5 0.6
108,0mm x 1 4.252 x 1.315 3.00 1.3
- -
100 x 25 108,0 x 33,4 76,2 0,6
108,0mm x 1-1/4 4.252 x 1.660 3.00 1.4
- -
100 x 32 108,0 x 42,4 76,2 0,6
108,0mm x 1-1/2 4.252 x 1.900 3.00 1.4
- -
100 x 40 108,0 x 48,3 76,2 0,6
108,0mm x 2 4.252 x 2.375 3.00 1.4
- -
100 x 50 108,0 x 60,3 76,2 0,6
108,0mm x 2-1/2 4.252 x 2.874 3.00 1.4
- -
100 x 65 108,0 x 73,0 76,2 0,6
108,0mm x 76mm 4.252 x 3.000 3.00 1.6
- -
100 x 65 108,0 x 76,1 76,2 0,7
TABLE 11 (1 OF 6)
FIGURES 250 AND 350 CAST AND FABRICATED CONCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 15 of 64

Figure 250 Figure 350

Nominal Pipe Size Cast Concentric Fabricated Concentric
Reducer Reducer

O.D. E to E Weight E to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

108,0mm x 3 4.252 x 3.500 3.00 1.7

- -
100 x 80 108,0 x 88,9 76,2 0,8
108,0mm x 4 4.252 x 4.500 3.00 2.3
- -
100 x 100 108,0 x 114,3 76,2 1,0
4x1 4.500 x 1.315 3.00 2.2
- -
100 x 25 114,3 x 33,4 76,2 0,9
4 x 1-1/4 4.500 x 1.660 3.00 2.2
- -
100 x 32 114,3 x 42,4 76,2 0,9
4 x 1-1/2 4.500 x 1.900 3.00 2.2
- -
100 x 40 114,3 x 48,3 76,2 0,9
4x2 4.500 x 2.375 3.00 2.4 3.00 2.3
100 x 50 114,3 x 60,3 76,2 1,1 76,2 1,0
4 x 2-1/2 4.500 x 2.874 3.00 2.7 3.00 2.2 E to E
100 x 65 114,3 x 73,0 76,2 1,2 76,2 0,9
4 x 76,1mm 4.500 x 3.000 3.00 3.2 3.00 2.4
100 x 65 114,3 x 76,1 76,2 1,5 76,2 1,0
4x3 4.500 x 3.500 3.00 2.8 3.00 2.5
100 x 80 114,3 x 88,9 76,2 1,3 76,2 1,1
FIGURE 250
133,0mm x 2 5.250 x 2.375 3.50 2.3 CAST CONCENTRIC
- -
125 x 50 133,0 x 60,3 88,9 1,0 REDUCER
133,0mm x 2-1/2 5.250 x 2.874 3.50 2.3
- -
125 x 65 133,0 x 73,0 88,9 1,0
133,0mm x 76,1mm 5.250 x 3.000 3.50 2.5 E to E
- -
125 x 65 133,0 x 76,1 88,9 1,1
133,0mm x 3 5.250 x 3.500 3.50 2.7
- -
125 x 80 133,0 x 88,9 88,9 1,2
133,0mm x 108,0mm 5.250 x 4.252 3.50 2.2
- -
125 x 100 133,0 x 108,0 88,9 0,9
FIGURE 350
133,0mm x 4 5.250 x 4.500 3.50 2.9 FABRICATED CONCENTRIC
- - REDUCER
125 x 100 133,0 x 114,3 88,9 1,3
139,7mm x 2 5.500 x 2.375 3.50 2.7
- -
125 x 50 139,7 x 60,3 88,9 1,2
139,7mm x 2-1/2 5.500 x 2.874 3.50 2.7
- -
125 x 65 139,7 x 73,0 88,9 1,2
139,7mm x 76,1mm 5.500 x 3.000 3.50 2.9
- -
125 x 65 139,7 x 76,1 88,9 1,3
139,7mm x 3 5.500 x 3.500 3.50 4.2 3.50 3.0
125 x 80 139,7 x 88,9 88,9 1,9 88,9 1,3
139,7mm x 4 5.500 x 4.500 3.50 4.4 3.50 3.2
125 x 100 139,7 x 114,3 88,9 2,0 88,9 1,5
5x2 5.563 x 2.375 3.50 3.7
- -
125 x 50 141,3 x 60,3 88,9 1,7
5 x 2-1/2 5.563 x 2.874 3.50 3.6
- -
125 x 65 141,3 x 73,0 88,9 1,6
5 x 76,1mm 5.563 x 3.000 3.50 3.8
- -
125 x 65 141,3 x 76,1 88,9 1,7
5x3 5.563 x 3.500 3.50 4.2 3.50 3.9
125 x 80 141,3 x 88,9 88,9 1,9 88,9 1,8
5 x 108,0mm 5.563 x 4.252 3.50 3.3
- -
125 x 100 141,3 x 108,0 88,9 1,5
5x4 5.563 x 4.500 3.50 4.4 3.50 4.0
125 x 100 141,3 x 114,3 88,9 2,0 88,9 1,8
TABLE 11 (2 OF 6)
FIGURES 250 AND 350 CAST AND FABRICATED CONCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 16 of 64

Figure 250 Figure 350

Nominal Pipe Size Cast Concentric Fabricated Concentric
Reducer Reducer

O.D. E to E Weight E to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

5 x 139,7mm 5.563 x 5.500 3.50 3.4

- -
125 x 125 141,3 x 139,7 88,9 1,5
159,0mm x 3 6.250 x 3.500 4.00 3.9
- -
150 x 80 159,0 x 88,9 101,6 1,8
159,0mm x 108,0mm 6.250 x 4.252 4.00 3.4
- -
150 x 108 159,0 x 108,0 101,6 1,5
159,0mmx 4 6.250 x 4.500 4.00 4.1
- -
150 x 100 159,0 x 114,3 101,6 1,9
159,0mm x 133,0mm 6.250 x 5.250 4.00 3.4
- -
150 x 125 159,0 x 133,0 101,6 1,5
159,0mm x 139,7mm 6.250 x 5.500 4.00 3.8
- -
150 x 125 159,0 x 139,7 101,6 1,7
E to E 165,1mm x 3 6.500 x 3.500 4.00 5.5 4.00 4.4
150 x 80 165,1 x 88,9 101,6 2,5 101,6 1,9
165,1mm x 4 6.500 x 4.500 4.00 6.0. 4.00 4.6
150 x 100 165,1 x 114,3 101,6 2,7 101,6 2,0
165,1mm x 139,7mm 6.500 x 5.500 4.00 5.6 4.00 4.2
150 x 125 165,1 x 139,7 101,6 2,5 101,6 1,9
FIGURE 250
CAST CONCENTRIC 165,1mm x 5 6.500 x 5.563 4.00 4.8
- -
REDUCER 150 x 125 165,1 x 141,3 101,6 2,2
6x2 6.625 x 2.375 4.00 5.3 4.00 5.6
150 x 50 168,3 x 60,3 101,6 2,4 101,6 2,5
E to E 6 x 2-1/2 6.625 x 2.874 4.00 5.7 4.00 5.5
150 x 65 168,3 x 73,0 101,6 2,6 101,6 2,5
6 x 76,1mm 6.625 x 3.000 4.00 6.1 4.00 5.7
150 x 65 168,3 x 76,1 101,6 2,7 101,6 2,6
6x3 6.625 x 3.500 4.00 5.8 4.00 5.9
150 x 80 168,3 x 88,9 101,6 2,6 101,6 2,7
FIGURE 350
FABRICATED CONCENTRIC 6 x 108,0mm 6.625 x 4.252 4.00 5.2
REDUCER - -
150 x 100 168,3 x 108,0 101,6 2,4
6x4 6.625 x 4.500 4.00 6.0 4.00 5.9
150 x 100 168,3 x 114,3 101,6 2,7 101,6 2,7
6 x 133,0mm 6.625 x 5.250 4.00 5.0
- -
150 x 125 168,3 x 133,0 101,6 2,3
6 x 139,7mm 6.625 x 5.500 4.00 6.3 4.00 5.3
150 x 100 168,3 x 139,7 101,6 2,3 101,6 2,4
6x5 6.625 x 5.563 4.00 6.2 4.00 6.0
150 x 125 168,3 x 141,3 101,6 2,8 101,6 2,7
216,3mm x 2-1/2 8.516 x 2.874 5.00 7.7
- -
200 x 65 216,3 x 73,0 127,0 3,5
216,3mm x 3 8.516 x 3.500 5.00 8.2
- -
200 x 80 216,3 x 88,9 127,0 3,7
216,3mm x 4 8.516 x 4.500 5.00 8.5
- -
200 x 100 216,3 x 114,3 127,0 3,9
216,3mm x 139,7mm 8.516 x 5.500 5.00 8.0
- -
200 x 125 216,3 x 139,7 127,0 3,6
216,3mm x 5 8.516 x 5.563 5.00 8.8
- -
200 x 125 216,3 x 141,3 127,0 3,9
216,3mm x 165,1mm 8.516 x 6.500 5.00 7.9
- -
200 x 165 216,3 x 165,1 127,0 3,6
216,3mm x 6 8.516 x 6.625 5.00 9.1
- -
200 x 150 216,3 x 168,3 127,0 4,1
TABLE 11 (3 OF 6)
FIGURES 250 AND 350 CAST AND FABRICATED CONCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 17 of 64

Figure 250 Figure 350

Nominal Pipe Size Cast Concentric Fabricated Concentric
Reducer Reducer

O.D. E to E Weight E to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

8 x 2-1/2 8.625 x 2.874 5.00 10.6

- -
200 x 65 219,1 x 73,0 127,0 4,8
8x3 8.625 x 3.500 5.00 11.5 5.00 11.0
200 x 80 219,1 x 88,9 127,0 5,2 127,0 4,9
8x4 8.625 x 4.500 5.00 10.7 5.00 11.2
200 x 100 219,1 x 114,3 127,0 4,9 127,0 5,1
8 x 133,0mm 8.625 x 5.250 5.00 10.1
- -
200 x 125 219,1 x 133,0 127,0 4,6
8 x 139,7mm 8.625 x 5.500 5.00 10.0 5.00 10.5
200 x 125 219,1 x 139.7 127,0 4,5 127,0 4,8
8x5 8.625 x 5.563 5.00 10.8 5.00 11.3
200 x 125 219,1 x 141,3 127,0 4,9 127,0 5,1
8 x 159,0mm 8.625 x 6.250 5.00 9.9 E to E
- -
200 x 150 219,1 x 159,0 127,0 4,5
8 x 165,1mm 8.625 x 6.500 5.00 11.0 5.00 10.1
200 x 150 219,1 x 165.1 127,0 5,0 127,0 4,6
8x6 8.625 x 6.625 5.00 11.3 5.00 11.3
200 x 150 219,1 x 168,3 127,0 5,1 127,0 5,1
FIGURE 250
267,4mm x 4 10.528 x 4.500 6.00 14.1 CAST CONCENTRIC
- -
250 x 100 267,4 x 114,3 152,4 6,4 REDUCER
267,4mm x 5 10.528 x 5.563 6.00 14.5
- -
250 x 125 267,4 x 141,3 152,4 6,6
267,4mm x 165,1mm 10.528 x 6.500 6.00 13.4 E to E
- -
250 x 125 267,4 x 165,1 152,4 6,1
267,4mm x 6 10.528 x 6.625 6.00 14.9
- -
250 x 150 267,4 x 168,3 152,4 6,8
267,4mm x 216,3mm 10.528 x 8.516 6.00 13.5
- -
250 x 216 267,4 x 216,3 152,4 6,1
FIGURE 350
267,4mm x 8 10.528 x 8.625 6.00 15.6 FABRICATED CONCENTRIC
- - REDUCER
250 x 200 267,4 x 219,1 152,4 7,1
10 x 4 10.750 x 4.500 6.00 19.1
- -
250 x 100 273,0 x 114,3 152,4 8,7
10 x 5 10.750 x 5.563 6.00 19.2
- -
250 x 125 273,0 x 141,3 152,4 8,7
10 x 159,0mm 10.750 x 6.250 6.00 17.7
- -
250 x 125 273,0 x 159,0 152,4 8,0
10 x 165,1mm 10.750 x 6.500 6.00 17.8 6.00 17.9
250 x 150 273,0 x 165,1 152,4 8,0 152,4 8,1
10 x 6 10.750 x 6.625 6.00 16.3 6.00 19.4
250 x 150 273,0 x 168,3 152,4 7,4 152,4 8,8
10 x 216,3mm 10.750 x 8.516 6.00 17.3
- -
250 x 200 273,0 x 216,3 152,4 7,8
10 x 8 10.750 x 8.625 6.00 18.3 6.00 19.5
250 x 200 273,0 x 219,1 152,4 8,3 152,4 8,8
318,5mm x 4 12.539 x 4.500 7.00 20.5
- -
300 x 100 318,5 x 114,3 177,8 9,3
318,5mm x 6 12.539 x 6.625 7.00 21.6
- -
300 x 150 318,5 x 168,3 177,8 9,8
318,5mm x 216,3mm 12.539 x 8.516 7.00 20.1
- -
300 x 200 318,5 x 216,3 177,8 9,1
318,5mm x 8 12.539 x 8.625 7.00 22.6
- -
300 x 200 318,5 x 219,1 177,8 10,3
TABLE 11 (4 OF 6)
FIGURES 250 AND 350 CAST AND FABRICATED CONCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 18 of 64

Figure 250 Figure 350

Nominal Pipe Size Cast Concentric Fabricated Concentric
Reducer Reducer

O.D. E to E Weight E to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

318,5mm x 267,4mm 12.539 x 10.528 7.00 20.3

- -
300 x 250 318,5 x 267,4 177,8 9,2
318,5mm x 10 12.539 x 10.750 7.00 23.8
- -
300 x 250 318,5 x 273,0 177,8 10,8
12 x 4 12.750 x 4.500 7.00 22.7 7.00 27.5
300 x 100 323,9 x 114,3 177,8 10,3 177,8 12,5
12 x 6 12.750 x 6.625 7.00 24.2 7.00 28.1
300 x 150 323,9 x 168,3 177,8 11,0 177,8 12,7
E to E
12 x 216,3mm 12.750 x 8.516 7.00 26.0
- -
300 x 200 323,9 x 216,3 177,8 11,8
12 x 8 12.750 x 8.625 7.00 25.8 7.00 28.5
300 x 200 323,9 x 219,1 177,8 11,7 177,8 12,9
12 x 267,4mm 12.750 x 10.528 7.00 25.4
- -
FIGURE 250 300 x 250 323,9 x 267,4 177,8 11,5
CAST CONCENTRIC
REDUCER 12 x 10 12.750 x 10.750 7.00 28.2 7.00 28.8
300 x 250 323,9 x 273,0 177,8 12,8 177,8 13,1
14 x 6 14.000 x 6.625 13.00 50.5
- -
350 x 150 355,6 x 168,3 330,2 23,0
E to E
14 x 8 14.000 x 8.625 13.00 53.3
- -
350 x 200 355,6 x 219,1 330,2 24,2
14 x 267,4mm 14.000 x 10.528 13.00 50.1
- -
350 x 250 355,6 x 267,4 330,2 22,7
14 x 10 14.000 x 10.750 13.00 56.6
FIGURE 350 - -
350 x 250 355,6 x 273,0 330,2 25,7
FABRICATED CONCENTRIC
REDUCER 14 x 318,5mm 14.000 x 12.539 13.00 50.3
- -
350 x 300 355.6 x 318.5 330,2 22,8
14 x 12 14.000 x 12.750 13.00 57.8
- -
350 x 300 355,6 x 323,9 330,2 26,2
377,0mm x 6 14.842 x 6.625 13.50 48.7
- -
350 x 150 377,0 x 168,3 342,9 22,1
377,0mm x 216,3mm 14.842 x 10.528 13.50 47.3
- -
350 x 250 377,0 x 267,4 342,9 21,4
377,0mm x 8 14.842 x 8.625 13.50 52.1
- -
350 x 200 377,0 x 219,1 342,9 23,6
377,0mm x 267,4mm 14.842 x 10.528 13.50 49.4
- -
350 x 250 377,0 x 267,4 342,9 22,4
377,0mm x 10 14.842 x 10.750 13.50 56.1
- -
350 x 250 377,0 x 273,0 342,9 25,4
377,0mm x 318,5mm 14.842 x 12.539 13.50 50.3
- -
350 x 300 377,0 x 318,5 342,9 22,8
377,0mm x 12 14.842 x 12.750 13.50 58.1
- -
350 x 300 377,0 x 323,9 342,9 26,4
TABLE 11 (5 OF 6)
FIGURES 250 AND 350 CAST AND FABRICATED CONCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 19 of 64

Figure 250 Figure 350

Nominal Pipe Size Cast Concentric Fabricated Concentric
Reducer Reducer

O.D. E to E Weight E to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

16 x 8 16.000 x 8.625 14.00 66

- -
400 x 200 406,4 x 219,1 355,6 29,9
16 x 267,4mm 16.000 x 10.528 14.00 62.9
- -
400 x 250 406,4 x 267,4 355,6 28,5
16 x 10 16.000 x 10.750 14.00 69.8
- -
400 x 250 406,4 x 273,0 355,6 31,7
16 x 318,5mm 16.000 x 12.539 14.00 63.3
- -
400 x 300 406,4 x 318,5 355,6 28,7
E to E
16 x 12 16.000 x 12.750 14.00 71.4
- -
400 x 300 406,4 x 323,9 355,6 32,4
16 x 14 16.000 x 14.000 14.00 71.7
- -
400 x 350 406,4 x 355,6 355,6 32,5
18 x 12 18.000 x 12.750 15.00 86.4
- -
450 x 300 457,2 x 323,9 381,0 39,2 FIGURE 250
CAST CONCENTRIC
18 x 14 18.000 x 14.000 15.00 86.8 REDUCER
- -
450 x 350 457,2 x 355,6 381,0 39,2
18 x 16 18.000 x 16.000 15.00 87.0
- -
450 x 400 457,2 x 406,4 381,0 39,5
E to E
20 x 10 20.000 x 10.750 20.00 120.2
- -
500 x 250 508,0 x 273,0 508,0 54,5
20 x 12 20.000 x 12.750 20.00 124.0
- -
500 x 300 508,0 x 323,9 508,0 56,2
20 x 14 20.000 x 14.000 20.00 125.5
- - FIGURE 350
500 x 350 508,0 x 355,6 508,0 56,9
FABRICATED CONCENTRIC
20 x 16 20.000 x 16.000 20.00 127.4 REDUCER
- -
500 x 400 508,0 x 406,4 508,0 57,8
20 x 18 20.000 x 18.000 20.00 128.5
- -
500 x 450 508,0 x 457,2 508,0 58,3
24 x 10 24.000 x 10.750 20.00 146.8
- -
600 x 250 609,6 x 273,0 508,0 66,6
24 x 12 24.000 x 12.750 20.00 150.7
- -
600 x 300 609,6 x 323,9 508,0 68,4
24 x 14 24.000 x 14.000 20.00 152.1
- -
600 x 350 609,6 x 355,6 508,0 69,0
24 x 16 24.000 x 16.000 20.00 154.0
- -
600 x 400 609,6 x 406,4 508,0 69,9
24 x 18 24.000 x 18.000 20.00 155.2
- -
600 x 450 609,6 x 457,2 508,0 70,4
24 x 20 24.000 x 20.000 20.00 155.4
- -
600 x 500 609,6 x 508,0 508,0 70,5

TABLE 11 (6 OF 6)
FIGURES 250 AND 350 CAST AND FABRICATED CONCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 20 of 64

Figure 221 Figure 321

Nominal Pipe Size Cast Fabricated
Reducing Tee Reducing Tee

O.D. C to E Weight C to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

1-1/2 x 1-1/2 x 1-1/4 1.900 x 1.900 x 1.660 2.75 1.5

- -
40 x 40 x 32 48,3 x 48,3 x 42,4 69,9 0,7
2x2x1 2.375 x 2.375 x 1.315 3.25 2.1
- -
50 x 50 x 25 60,3 x 60,3 x 33,4 82,6 0,9
2 x 2 x 1-1/2 2.375 x 2.375 x 1.900 3.25 2.7 3.25 2.3
50 x 50 x 40 60,3 x 60,3 x 48,3 82,6 1,2 82,6 1,0
2-1/2 x 2-1/2 x 1 2.874 x 2.874 x 1.315 3.75 2.8
- -
65 x 65 x 25 73,0 x 73,0 x 33,4 95,3 1,3
2-1/2 x 2-1/2 x 1-1/4 2.874 x 2.874 x 1.660 3.75 3.0
- -
65 x 65 x 32 73,0 x 73,0 x 42,4 95,3 1,4
2-1/2 x 2-1/2 x 1-1/2 2.874 x 2.874 x 1.900 3.75 3.0
- -
65 x 65 x 40 73,0 x 73,0 x 48,3 95,3 1,4
C to E
2-1/2 x 2-1/2 x 2 2.874 x 2.87 x 2.375 3.75 4.2 3.75 3.1
65 x 65 x 50 73,0 x 73,0 x 60,3 95,3 1,9 95,3 1,4
76,1mm x 76,1mm x 1 3.000 x 3.000 x 1.315 3.75 3.6
- -
65 x 65 x 25 76,1 x 76,1 x 33,4 95,3 1,6
76,1mm x 76,1mm x 1-1/4 3.000 x 3.000 x 1.660 3.75 3.7
C to E - -
65 x 65 x 32 76,1 x 76,1 x 42,4 95,3 1,7
FIGURE 221 76,1mm x 76,1mm x 1-1/2 3.000 x 3.000 x 1.900 3.75 4.5 3.75 3.8
CAST REDUCING TEE 65 x 65 x 40 76,1 x 76,1 x 48,3 95,3 2,0 95,3 1,7
76,1mm x 76,1mm x 2 3.000 x 3.000 x 2.375 3.75 4.3 3.75 4.0
65 x 65 x 50 76,1 x 76,1 x 60,3 95,3 2,0 95,3 1,8
C to E
3x3x1 3.500 x 3.500 x 1.315 4.25 5.6 4.25 5.5
80 x 80 x 25 88,9 x 88,9 x 33,4 108,0 2,5 108,0 2,5
3 x 3 x 1-1/2 3.500 x 3.500 x 1.900 4.25 5.9 4.25 5.6
80 x 80 x 40 88,9 x 88,9 x 48,3 108,0 2,7 108,0 2,5
3x3x2 3.500 x 3.500 x 2.375 4.25 6.0 4.25 5.8
C to E 80 x 80 x 50 88,9 x 88,9 x 60,3 108,0 2,7 108,0 2,6
FIGURE 321 3 x 3 x 2-1/2 3.500 x 3.500 x 2.874 4.25 6.2 4.25 6.0
FABRICATED 80 x 80 x 65 88,9 x 88,9 x 73,0 108,0 2,8 108,0 2,7
REDUCING TEE
(SEGMENT WELDED) 3 x 3 x 76,1mm 3.500 x 3.500 x 3.000 4.25 6.0 4.25 6.1
80 x 80 x 65 88,9 x 88,9 x 76,1 108,0 2,7 108,0 2,8
108,0mm x 108,0mm x 2 4.252 x 4.252 x 2.375 5.00 5.7
- -
100 x 100 x 50 108,0 x 108,0 x 60,3 127,0 2,6
108,0mm x 108,0mm x 2-1/2 4.252 x 4.252 x 2.874 5.00 6.0
- -
100 x 100 x 65 108,0 x 108,0 x 73,0 127,0 2,7
108,0mm x 108,0mm x 76,1mm 4.252 x 4.252 x 3.000 5.00 6.1
- -
100 x 100 x 65 108,0 x 108,0 x 76,1 127,0 2,8
108,0mm x 108,0mm x 3 4.252 x 4.252 x 3.500 5.00 6.6
- -
100 x 100 x 80 108,0 x 108,0 x 88,9 127,0 2,9
4x4x1 4.500 x 4.500 x 1.315 5.00 9.0
- -
100 x 100 x 25 114,3 x 114,3 x 33,4 127,0 4,0
4 x 4 x 1-1/4 4.500 x 4.500 x 1.660 5.00 9.1
- -
100 x 100 x 32 114,3 x 114,3 x 42,4 127,0 4,1
4 x 4 x 1-1/2 4.500 x 4.500 x 1.900 5.00 9.2
- -
100 x 100 x 40 114,3 x 114,3 x 48,3 127,0 4,1
4x4x2 4.500 x 4.500 x 2.375 5.00 9.1 5.00 9.3
100 x 100 x 50 114,3 x 114,3 x 60,3 127,0 4,1 127,0 4,2
4 x 4 x 2-1/2 4.500 x 4.500 x 2.874 5.00 9.5 5.00 9.7
100 x 100 x 65 114,3 x 114,3 x 73,0 127,0 4,3 127,0 4,4
4 x 4 x 76,1mm 4.500 x 4.500 x 3.000 5.00 9.5 5.00 9.7
125 x 125 x 65 114,3 x 114,3 x 76,1 127,0 4,3 127,0 4,4
TABLE 12 (1 OF 6)
FIGURES 221 AND 321 CAST AND FABRICATED REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 21 of 64

Figure 221 Figure 321

Nominal Pipe Size Cast Fabricated
Reducing Tee Reducing Tee

O.D. C to E Weight C to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

4x4x3 4.500 x 4.500 x 3.500 5.00 9.7 5.00 10.1

100 x 100 x 80 114,3 x 114,3 x 88,9 127,0 4,4 127,0 4,6
133,0mm x 133,0mm x 2 5.250 x 5.250 x 2.375 5.50 8.2
- -
125 x 125 x 50 133,0 x 133,0 x 60,3 139,7 3,7
133,0mm x 133,0mm x 2-1/2 5.250 x 5.250 x 2.874 5.50 8.6
- -
125 x 125 x 65 133,0 x 133,0 x 73,0 139,7 3,9
133,0mm x 133,0mm x 76,1mm 5.250 x 5.250 x 3.000 5.50 8.7
- -
125 x 125 x 65 133,0 x 133,0 x 76,1 139,7 3,9
133,0mm x 133,0mm x 3 5.250 x 5.250 x 3.500 5.50 9.1
- -
125 x 125 x 80 133,0 x 133,0 x 88,9 139,7 4,1
133,0mm x 133,0mm x 108,0mm 5.250 x 5.250 x 4.252 5.50 8.5
- -
125 x 125 x 100 133,0 x 133,0 x 108,0 139,7 3,9
C to E
133,0mm x 133,0mm x 4 5.250 x 5.250 x 4.500 5.50 9.8
- -
125 x 125 x 100 133,0 x 133,0 x 114,3 139,7 4,4
139,7mm x 139,7mm x 2 5.500 x 5.500 x 2.375 5.50 10.1
- -
125 x 125 x 50 139,7 x 139,7 x 60,3 139,7 4,6
139,7mm x 139,7mm x 2-1/2 5.500 x 5.500 x 2.874 5.50 10.5
- - C to E
125 x 125 x 65 139,7 x 139,7 x 73,0 139,7 4,8
139,7mm x 139,7mm x 76,1mm 5.500 x 5.500 x 3.000 5.50 10.5 FIGURE 221
- - CAST REDUCING TEE
125 x 125 x 65 139,7 x 139,7 x 76,1 139,7 4,8
139,7mm x 139,7mm x 3 5.500 x 5.500 x 3.500 5.50 12.7 5.50 11.0
125 x 125 x 80 139,7 x 139,7 x 88,9 139,7 5,8 139,7 4,9
C to E
139,7mm x 139,7mm x 4 5.500 x 5.500 x 4.500 5.50 13.4 5.50 11.5
125 x 125 x 100 139,7 x 139,7 x 114,3 139,7 6,1 139,7 5,2
5x5x2 5.563 x 5.563 x 2.375 5.50 13.6
- -
125 x 125 x 50 141,3 x 141,3 x 60,3 139,7 6,2
5 x 5 x 2-1/2 5.563 x 5.563 x 2.874 5.50 18.0 5.50 14.0
125 x 125 x 65 141,3 x 141,3 x 73,0 139,7 8,2 139,7 6,4 C to E
5 x 5 x 76,1mm 5.563 x 5.563 x 3.000 5.50 14.0 FIGURE 321
- - FABRICATED
125 x 125 x 65 141,3 x 141,3 x 76,1 139,7 6,4
REDUCING TEE
5x5x3 5.563 x 5.563 x 3.500 5.50 14.0 5.50 14.3 (SEGMENT WELDED)
125 x 125 x 80 141,3 x 141,3 x 88,9 139,7 6,4 139,7 6,5
5x5x4 5.563 x 5.563 x 4.500 5.50 13.9 5.50 14.8
125 x 125 x 100 141,3 x 141,3 x 114,3 139,7 6,3 139,7 6,7
159,0mm x 159,0mm x 2-1/2 6.250 x 6.250 x 2.874 6.50 13.3
- -
150 x 150 x 65 159,0 x 159,0 x 73,0 165,1 6,0
159,0mm x 159,0mm x 76,1mm 6.250 x 6.250 x 3.000 6.50 13.4
- -
150 x 150 x 65 159,0 x 159,0 x 76,1 165,1 6,1
159,0mm x 159,0mm x 3 6.250 x 6.250 x 3.500 6.50 13.9
- -
150 x 150 x 80 159,0 x 159,0 x 88,9 165,1 6,3
159,0mm x 159,0mm x 108,0mm 6.250 x 6.250 x 4.252 6.50 13.2
- -
150 x 150 x 100 159,0 x 159,0 x 108,0 165,1 6,0
159,0mm x 159,0mm x 4 6.250 x 6.250 x 4.500 6.50 14.7
- -
150 x 150 x 100 159,0 x 159,0 x 114,3 165,1 6,7
159,0mm x 159,0mm x 133,0mm 6.250 x 6.250 x 5.250 6.50 13.7
- -
150 x 150 x 125 159,0 x 159,0 x 133,0 165,1 6,2
159,0mm x 159,0mm x 139,7mm 6.250 x 6.250 x 6.500 6.50 14.5
- -
150 x 150 x 125 159,0 x 159,0 x 139,7 165,1 6,6
159,0mm x 159,0mm x 5 6.250 x 6.250 x 5.63 6.50 15.7
- -
150 x 150 x 125 159,0 x 159,0 x 141,3 165,1 7,1
165,1mm x 165,1mm x 2-1/2 6.500 x 6.500 x 2.874 6.50 15.2
- -
150 x 150 x 65 165,1 x 165,1 x 73,0 165,1 6,9
TABLE 12 (2 OF 6)
FIGURES 221 AND 321 CAST AND FABRICATED REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 22 of 64

Figure 221 Figure 321

Nominal Pipe Size Cast Fabricated
Reducing Tee Reducing Tee

O.D. C to E Weight C to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

165,1mm x 165,1mm x 76,1mm 6.500 x 6.500 x 3.000 6.50 15.2

- -
150 x 150 x 65 165,1 x 165,1 x 76,1 165,1 6,9
165,1mm x 165,1mm x 139,7mm 6.500 x 6.500 x 5.500 6.50 15.2
- -
150 x 150 x 125 165,1 x 165,1 x 139,7 165,1 6,9
165,1mm x 165,1mm x 3 6.500 x 6.500 x 3.500 6.50 18.0 6.50 15.7
150 x 150 x 80 165,1 x 165,1 x 88,9 165,1 8,2 165,1 7,1
165,1mm x 165,1mm x 4 6.500 x 6.500 x 4.500 6.50 19.5 6.50 16.4
150 x 150 x 100 165,1 x 165,1 x 114,3 165,1 8,9 165,1 7,4
165,1mm x 165,1mm x 5 6.500 x 6.500 x 5.563 6.50 17.3
- -
150 x 150 x 125 165,1 x 165,1 x 141,3 165,1 7,8
6x6x2 6.625 x 6.625 x 2.375 6.50 19.4 6.50 20.8
150 x 150 x 50 168,3 x 168,3 x 60,3 165,1 8,8 165,1 9,4
C to E
6 x 6 x 2-1/2 6.625 x 6.625 x 2.874 6.50 21.2 6.50 21.2
150 x 150 x 65 168,3 x 168,3 x 73,0 165,1 9,8 165,1 9,6
6 x 6 x 76,1mm 6.625 x 6.625 x 3.000 6.50 21.2 6.50 21.2
150 x 150 x 65 168,3 x 168,3 x 76,1 165,1 9,8 165,1 9,6
6x6x3 6.625 x 6.625 x 3.500 6.50 21.0 6.50 21.6
C to E 150 x 150 x 80 168,3 x 168,3 x 88,9 165,1 9,5 165,1 9,8
FIGURE 221 6x6x4 6.625 x 6.625 x 4.500 6.50 21.8 6.50 22.2
CAST REDUCING TEE 150 x 150 x 100 168,3 x 168,3 x 114,3 165,1 9,9 165,1 10,1
6 x 6 x 139,7mm 6.625 x 6.625 x 5.500 6.50 23.0 6.50 21.7
150 x 150 x 125 168,3 x 168,3 x 139,7 165,1 10,4 165,1 9,8
C to E
6x6x5 6.625 x 6.625 x 5.563 6.50 22.9
- -
150 x 150 x 125 168,3 x 168,3 x 141,3 165,1 10,4
216,3mm x 216,3mm x 2 8.516 x 8.516 x 2.375 7.75 26.2
- -
200 x 200 x 50 216,3 x 216,3 x 60,3 196,9 11,8
216,3mm x 216,3mm x 2-1/2 8.516 x 8.516 x 2.874 7.75 26.7
C to E - -
200 x 200 x 65 216,3 x 216,3 x 73,0 196,9 12,1
FIGURE 321 216,3mm x 216,3mm x 76,1mm 8.516 x 8.516 x 3.000 7.75 26.7
FABRICATED - -
200 x 200 x 65 216,3 x 216,3 x 76,1 196,9 12,1
REDUCING TEE
(SEGMENT WELDED) 216,3mm x 216,3mm x 3 8.516 x 8.516 x 3.500 7.75 27.2
- -
200 x 200 x 80 216,3 x 216,3 x 88,9 196,9 12,3
216,3mm x 216,3mm x 4 8.516 x 8.516 x 4.500 7.75 27.8
- -
200 x 200 x 100 216,3 x 216,3 x 114,1 196,9 12,6
216,3mm x 216,3mm x 139,7mm 8.516 x 8.516 x 5.500 7.75 27.5
- -
200 x 200 x 125 216,3 x 216,3 x 139,7 196,9 12,5
216,3mm x 216,3mm x 5 8.516 x 8.516 x 5.563 7.75 28.7
- -
200 x 200 x 125 216,3 x 2165,3 x 141,3 196,9 13,0
216,3mm x 216,3mm x 165,1mm 8.516 x 8.516 x 6.500 7.75 28.3
- -
200 x 200 x 150 216,3 x 216,3 x 165,1 196,9 12,8
216,3mm x 216,3mm x 6 8.516 x 8.516 x 6.625 7.75 29.8
- -
200 x 200 x 150 216,3 x 216,3 x 168,3 196,9 13,5
8x8x2 8.625 x 8.625 x 2.375 7.75 36.9
- -
200 x 200 x 50 219,1 x 219,1 x 60,3 196,9 16,7
8 x 8 x 2-1/2 8.625 x 8.625 x 2.874 7.75 37.3
- -
200 x 200 x 65 219,1 x 219,1 x 73,0 196,9 17,0
8 x 8 x 76,1mm 8.625 x 8.625 x 3.000 7.75 37.3
- -
200 x 200 x 65 216,1 x 219,1 x 76.1 196,9 17,0
8x8x3 8.625 x 8.625 x 3.500 7.75 37.7
- -
200 x 200 x 80 219,1 x 219,1 x 88,9 196,9 17,1
8x8x4 8.625 x 8.625 x 4.500 7.75 37.2 7.75 38.2
200 x 200 x 100 219,1 x 219,1 x 114,1 196,9 16,9 196,9 17,3
TABLE 12 (3 OF 6)
FIGURES 221 AND 321 CAST AND FABRICATED REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 23 of 64

Figure 221 Figure 321

Nominal Pipe Size Cast Fabricated
Reducing Tee Reducing Tee

O.D. C to E Weight C to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

8 x 8 x 139,7mm 8.625 x 8.625 x 5.563 7.75 37.7 7.75 37.7

200 x 200 x 125 219,1 x 219,1 x 139,7 196,9 17,1 196,9 17,1
8x8x5 8.625 x 8.625 x 5.500 7.75 38.8
- -
200 x 200 x 125 219,1 x 219,1 x 141,3 196,9 17,6
8 x 8 x 165,1mm 8.625 x 8.625 x 6.500 7.75 37.7 7.75 38.2
200 x 200 x 150 219,1 x 219,1 x 165,1 196,9 17,1 196,9 17,3
8x8x6 8.625 x 8.625 x 6.625 7.75 37.4 7.75 38.2
200 x 200 x 150 219,1 x 219,1 x 168,3 196,9 17,0 196,9 17,3
267,4mm x 267,4mm x 4 10.528 x 10.528 x 4.500 9.00 44.3
- -
250 x 250 x 100 267,4 x 267,4 x 114,3 228,6 20,1
267,4mm x 267,4mm x 139,7mm 10.528 x 10.528 x 5.500 9.00 43.9
- -
250 x 250 x 125 267,4 x 267,4 x 139,7 228,6 19,9
C to E
267,4mm x 267,4mm x 5 10.528 x 10.528 x 5.563 9.00 45.1
- -
250 x 250 x 125 267,4 x 267,4 x 141,3 228,6 20,4
267,4mm x 267,4mm x 165,1mm 10.528 x 10.528 x 6.500 9.00 44.6
- -
250 x 250 x 150 267,4 x 267,4 x 165,1 228,6 20,2
267,4mm x 267,4mm x 6 10.528 x 10.528 x 6.625 9.00 44.6
- - C to E
250 x 250 x 150 267,4 x 267,4 x 168,3 228,6 20,2
267,4mm x 267,4mm x 216,3mm 10.528 x 10.528 x 8.516 9.00 45.6 FIGURE 221
- - CAST REDUCING TEE
250 x 250 x 200 267,4 x 267,4 x 216,3 228,6 20,7
267,4mm x 267,4mm x 8 10.528 x 10.528 x 8.625 9.00 45.6
- -
250 x 250 x 200 267,4 x 267,4 x 219,1 228,6 20,7
C to E
10 x 10 x 2 10.750 x 10.750 x 2.375 9.00 60.5
- -
250 x 250 x 50 273,0 x 273,0 x 60,3 228,6 20,7
10 x 10 x 3 10.750 x 10.750 x 3.500 9.00 61.2
- -
250 x 250 x 80 273,0 x 273,0 x 88,9 228,6 27,8
10 x 10 x 4 10.750 x 10.750 x 4.500 9.00 61.7
- - C to E
250 x 250 x 100 273,0 x 273,0 x 114,3 228,6 27,9
10 x 10 x 139,7mm 10.750 x 10.750 x 5.500 9.00 61.0 FIGURE 321
- - FABRICATED
250 x 250 x 125 273,0 x 273,0 x 139,7 228,6 27,6
REDUCING TEE
10 x 10 x 5 10.750 x 10.750 x 5.563 9.00 62.3 (SEGMENT WELDED)
- -
250 x 250 x 125 273,0 x 273,0 x 141,3 228,6 28.3
10 x 10 x 165,1mm 10.75 x 10.750 x 6.500 9.00 61.5
- -
250 x 250 x 150 273,0 x 273,0 x 165,1 228,6 27,8
10 x 10 x 6 10.750 x 10.750 x 6.625 9.00 61.4
- -
250 x 250 x 150 273,0 x 273,0 x 168,3 228,6 27,8
10 x 10 x 216,3mm 10.750 x 10.750 x 8.516 9.00 61.6
- -
250 x 250 x 200 273,0 x 273,0 x 216,3 228,6 27,9
10 x 10 x 8 10.750 x 10.750 x 8.625 9.00 61.6
- -
250 x 250 x 200 273,0 x 273,0 x 219,1 228,6 27,9
318,5mm x 318,5mm x 4 12.539 x 12.539 x 4.500 10.00 60.5
- -
300 x 300 x 100 318,5 x 318,5 x 114,3 254,0 27,4
318,5mm x 318,5mm x 139,7mm 12.539 x 12.539 x 5.500 10.00 60.0
- -
300 x 300 x 125 318,5 x 318,5 x 139,7 254,0 27,2
318,5mm x 318,5mm x 5 12.539 x 12.539 x 5.563 10.00 61.2
- -
300 x 300 x 125 318,5 x 318,5 x 141,3 254,0 27,8
318,5mm x 318,5mm x 165,1mm 12.539 x 12.539 x 6.500 10.00 60.7
- -
300 x 300 x 150 318,5 x 318,5 x 165,1 254,0 27,5
318,5mm x 318,5mm x 6 12.539 x 12.539 x 6.625 10.00 60.7
- -
300 x 300 x 150 318,5 x 318,5 x 168,3 254,0 27,5
318,5mm x 318,5mm x 216,3mm 12.539 x 12.539 x 8.516 10.00 61.5
- -
300 x 300 x 200 318,5 x 318,5 x 216,3 254,0 27,9
TABLE 12 (4 OF 6)
FIGURES 221 AND 321 CAST AND FABRICATED REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 24 of 64

Figure 221 Figure 321

Nominal Pipe Size Cast Fabricated
Reducing Tee Reducing Tee

O.D. C to E Weight C to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

318,5mm x 318,5mm x 8 12.539 x 12.539 x 8.625 10.00 61.5

- -
300 x 300 x 200 318,5 x 318,5 x 219,1 254,0 27,9
318,5mm x 318,5mm x 267,4mm 12.539 x 12.539 x 10.528 10.00 62.2
- -
300 x 300 x 250 318,5 x 318,5 x 267,4 254,0 28,2
318,5mm x 318,5mm x 10 12.539 x 12.539 x 10.750 10.00 62.2
- -
300 x 300 x 250 318,5 x 318,5 x 273,0 254,0 28,2
C to E
12 x 12 x 3 12.750 x 12.750 x 3.500 10.00 82.7
- -
300 x 300 x 80 323,9 x 323,9 x 88,9 254,0 37,5
12 x 12 x 4 12.750 x 12.750 x 4.500 10.00 83.1
- -
300 x 300 x 100 323,9 x 323,9 x 114,3 254,0 37,7
12 x 12 x 139,7mm 12.750 x 12.750 x 5.500 10.00 82.5
C to E - -
300 x 300 x 125 323,9 x 323,9 x 139,7 254,0 37,4
FIGURE 221 12 x 12 x 5 12.750 x 12.750 x 5.563 10.00 83.7
CAST REDUCING TEE - -
300 x 300 x 125 323,9 x 323,9 x 141,3 254,0 37,9
12 x 12 x 165,1mm 12.750 x 12.750 x 6.500 10.00 82.8
- -
300 x 300 x 150 323,9 x 323,9 x 165,1 254,0 38.0
C to E
12 x 12 x 6 12.750 x 12.750 x 6.625 10.00 82.8
- -
300 x 300 x 150 323,9 x 323,9 x 168,3 254,0 38.0
12 x 12 x 216,3mm 12.750 x 12.750 x 8.516 10.00 82.8
- -
300 x 300 x 200 323,9 x 323,9 x 216,3 254,0 38.0
12 x 12 x 8 12.750 x 12.750 x 8.625 10.00 82.8
- -
C to E 300 x 300 x 200 323,9 x 323,9 x 219,1 254,0 38.0
FIGURE 321 12 x 12 x 267,4mm 12.750 x 12.750 x 10.528 10.00 82.5
FABRICATED - -
300 x 300 x 250 323,9 x 323,9 x 267,4 254,0 37,4
REDUCING TEE
(SEGMENT WELDED) 12 x 12 x 10 12.750 x 12.750 x 10.750 10.00 82.4
- -
300 x 300 x 250 323,9 x 323,9 x 273,0 254,0 37,4
14 x 14 x 6 14.000 x 14.000 x 6.625 11.00 100.5
- -
350 x 350 x 150 355,6 x 355,6 x 168,3 279,4 45,6
14 x 14 x 8 14.000 x 14.000 x 8.625 11.00 100.7
- -
350 x 350 x 200 355,6 x 355,6 x 219,1 279,4 45,7
14 x 14 x 10 14.000 x 14.000 x 10.750 11.00 100.5
- -
350 x 350 x 250 355,6 x 355,6 x 273,0 279,4 45,6
14 x 14 x 12 14.000 x 14.000 x 12.750 11.00 101.3
- -
350 x 350 x 300 355,6 x 355,6 x 323,9 279,4 45,9
16 x 16 x 4 16.000 x 16.000 x 4.500 12.00 125.5
- -
400 x 400 x 100 406,4 x 406,4 x 114,3 304,8 56,9
TABLE 12 (5 OF 6)
FIGURES 221 AND 321 CAST AND FABRICATED REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 25 of 64

Figure 221 Figure 321

Nominal Pipe Size Cast Fabricated
Reducing Tee Reducing Tee

O.D. C to E Weight C to E Weight

ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

16 x 16 x 8 16.000 x 16.000 x 8.625 12.00 125.6

- -
400 x 400 x 200 406,4 x 406,4 x 219,1 304,8 57,0
16 x 16 x 10 16.000 x 16.000 x 10.750 12.00 125.7
- -
400 x 400 x 250 406,4 x 406,4 x 273,0 304,8 57,0
16 x 16 x 12 16.000 x 16.000 x 12.750 12.00 125.8
- -
400 x 400 x 300 406,4 x 406,4 x 323,9 304,8 57,1
C to E
16 x 16 x 14 16.000 x 16.000 x 14.000 12.00 132.3
- -
400 x 400 x 350 406,4 x 406,4 x 355,6 304,8 60,0
18 x 18 x 8 18.000 x 18.000 x 8.625 15.50 186.7
- -
450 x 450 x 200 457,2 x 457,2 x 219,1 393,7 84,7
18 x 18 x 10 18.000 x 18.000 x 10.750 15.50 187.7
- - C to E
450 x 450 x 250 457,2 x 457,2 x 273,0 393,7 85,1
18 x 18 x 12 18.000 x 18.000 x 12.750 15.50 190.2 FIGURE 221
- - CAST REDUCING TEE
450 x 450 x 300 457,2 x 457,2 x 323,9 393,7 86,2
18 x 18 x 14 18.000 x 18.000 x 14.000 15.50 199.8
- -
450 x 450 x 350 457,2 x 457,2 x 355,6 393,7 90,6
C to E
18 x 18 x 16 18.000 x 18.000 x 16.000 15.50 202.1
- -
450 x 450 x 400 457,2 x 457,2 x 406,4 393,7 91,7
20 x 20 x 14 20.000 x 20.000 x 14.000 17.25 246.0
- -
500 x 500 x 350 508,0 x 508,0 x 355,6 450,9 111,6
20 x 20 x 16 20.000 x 20.000 x 16.000 17.25 248.5
- -
500 x 500 x 400 508,0 x 508,0 x 406,4 450,9 112,7 C to E
20 x 20 x 18 20.000 x 20.000 x 18.000 17.25 251.0 FIGURE 321
- - FABRICATED
500 x 500 x 450 508,0 x 508,0 x 457,2 450,9 113,8
REDUCING TEE
24 x 24 x 10 24.000 x 24.000 x 10.750 20.00 321.3 (SEGMENT WELDED)
- -
600 x 600 x 250 609,6 x 609,6 x 273,0 508,0 145,7
24 x 24 x 12 24.000 x 24.000 x 12.750 20.00 324.6
- -
600 x 600 x 300 609,6 x 609,6 x 323,9 508,0 147,2
24 x 24 x 14 24.000 x 24.000 x 14.000 20.00 335.8
- -
600 x 600 x 350 609,6 x 609,6 x 355,6 508,0 152,3
24 x 24 x 16 24.000 x 24.000 x 16.000 20.00 338.3
- -
600 x 600 x 400 609,6 x 609,6 x 406,4 508,0 153,5
24 x 24 x 18 24.000 x 24.000 x 18.000 20.00 340.7
- -
600 x 600 x 450 609,6 x 609,6 x 457,2 508,0 154,5
24 x 24 x 20 24.000 x 24.000 x 20.000 20.00 343.1
- -
600 x 600 x 500 609,6 x 609,6 x 508,0 508,0 155,6
TABLE 12 (6 OF 6)
FIGURES 221 AND 321 CAST AND FABRICATED REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 26 of 64

Figure 219 Figure 319

Nominal Pipe Size Cast Tee Fabricated Tee

ANSI O.D. C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

1-1/4 1.660 2.75 1.7 2.75 2.2

32 42,4 69,9 0,8 69,9 0,9
1-1/2 1.900 2.75 2.1 2.75 2.6
40 48,3 69,9 1,0 69,9 1,2
2 2.375 3.25 2.7 3.25 3.6
50 60,3 82,6 1,2 82,6 1,6
2-1/2 2.874 3.75 4.4 3.75 5.8
65 73,0 95,3 2,0 95,3 2,6
76,1mm 3.000 3.75 6.5 3.75 4.2
C to E 65 76,1 95,3 2,9 95,3 1,9
3 3.500 4.25 6.5 4.25 7.6
80 88,9 108,0 2,9 108,0 3,4
4 4.500 5.00 10.7 5.00 10.7
100 114,3 127,0 4,8 127,0 4,9
C to E 139,7mm 5.500 5.50 15.2 5.50 10.6
125 139,7 139,7 6,9 139,7 4,8
FIGURE 219
CAST TEE 5 5.563 5.50 15.5 5.50 13.9
125 141,3 139,7 7,0 139,7 6,3
165,1mm 6.500 6.50 24.2 6.50 13.2
C to E 150 165,1 165,1 11,0 165,1 5,9
6 6.625 6.50 23.0 6.50 18.9
150 168,3 165,1 10,4 165,1 8,6
216,3mm 8.500 7.75 43.0 7.75 19.9
200 216,3 196,9 19,5 196,9 9,0
C to E 8 8.625 7.75 43.7 7.75 28.3
200 219,1 196,9 19,8 196,9 12,8
FIGURE 319
FABRICATED TEE 267,4mm 10.528 9.00 30.8
- -
(SEGMENT WELDED) 250 267,4 228,6 13,9
10 10.750 9.00 57.0 9.00 44.4
250 273,0 228,6 25,9 228,6 20,1
318,5mm 12.539 10.00 45.3
300 - -
318,5 254,0 20,5
12 12.750 10.00 110.0 10.00 63.3
300 323,9 254,0 49,9 254,0 28,7
14 14.000 11.00 135.0 11.00 76.0
350 355,6 279,0 61,2 279,0 34,5
16 16.000 12.00 136.0 12.00 94.0
400 406,4 305,0 61,7 305,0 42,6
18 18.000 15.50 129.0
- -
450 457,2 394,0 58,5
20 20.000 17,25 158.0
- -
500 508,0 438,0 71,6
24 24.000 20.00 216.0
- -
600 609,6 508,0 97,9
TABLE 13
FIGURES 219 AND 319 CAST AND FABRICATED TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 27 of 64

Nominal Pipe Size

C to LE C to SE Weight
Inches Inches Lbs.
ANSI O.D. mm mm kg
Inches Inches
DN mm

1-1/4 1.660 5.75 2.50 1.4

32 42,4 146,1 63,5 0,6
1-1/2 1.900 6.25 2.75 1.7
40 48,3 158,8 69,9 0,8
2 2.375 7.00 2.75 2.5
50 60,3 177.8 69,9 1,1
2-1/2 2.874 7.75 3.00 4.4
65 73,0 196,9 76,2 2,0
76,1mm 3.000 7.75 3.00 4.4
65 76,1 196,9 76,2 2,0
3 3.500 8.50 3.25 6.4
80 88,9 215,9 82,6 2,9
108,0mm 4.252 10.50 3.75 9.7
100 108,0 266,7 95,3 4,4
4 4.500 10.50 3.75 10.5
100 114,3 266,7 95,3 4,8
133,0mm 5.250 12.50 4.00 15.6
125 133,0 317,5 102,0 7,1
139,7mm 5.500 12.50 4.00 30.0
125 139,7 317,5 102,0 13,6
5 5.563 12.50 4.00 15.2 C to LE
125 141,3 317,5 101,6 6,9
159,0mm 6.250 14.00 4.50 20.6 C to LE
150 159,0 355,6 114,3 9,4 C to SE
165,1mm 6.500 14.00 4.50 22.9
150 165,1 355,6 114,3 10,4
6 6.625 14.00 4.50 22.9
150 168,3 355,6 114,3 10,4
216,3mm 8.516 18.00 6.00 38.4
200 216,3 457,2 152,4 17,4
8 8.625 18.00 6.00 41.9
200 219,1 457,2 152,4 19,0
267,4mm 10.528 20.50 6.50 59.1
250 267,4 520,7 165,7 26,8
10 10.750 20.50 6.50 66.2
250 273,0 520,7 165,7 30,0
318,5mm 12.539 23.00 7.00 84.0
300 318,5 584,2 177,8 38.1
12 12.750 23.00 7.00 87.7
300 323,9 584,2 177,8 39,8
14 14.000 26.50 7.50 105.3
350 355,6 673,1 190,5 47,8
16 16.000 29.00 8.00 129.1
400 406,4 736,6 203,2 58,6
18 18.000 32.00 8.50 184.4
450 457,2 812,8 215,9 83,6
20 20.000 35.00 9.00 225.8
500 508,0 889,0 238,6 102,4
24 24.000 40.00 10.00 308.5
600 609,6 1016,0 254,0 139,9
TABLE 14
FIGURE 314 FABRICATED 45° LATERALS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 28 of 64

Nominal Pipe Size

C to LE C to SE Weight
O.D. Inches Inches Lbs.
ANSI Inches mm mm kg
Inches
DN mm
3x3x2 3.500 x 3.500 x 2.375 8.50 3.25 9.0
80 x 80 x 50 88,9 x 88,9 x 60,3 215,9 82,6 4,1
3 x 3 x 2-1/2 3.500 x 3.500 x 2.874 8.50 3.25 9.9
80 x 80 x 65 88,9 x 88,9 x 73,0 215,9 82,6 4,5
3 x 3 x 76,1mm 3.500 x 3.500 x 3.000 8.50 3.25 9.0
80 x 80 x 65 88,9 x 88,9 x 76,1 216,0 83,0 4,1
108,0mm x 108,0mm x 2 4.252 x 4.252 x 2.375 10.50 3.75 12.3
100 x 100 x 50 108,0 x 108,0 x 60,3 266,7 95,3 5,6
108,0mm x 108,0mm x 2-1/2 4.252 x 4.252 x 2.874 10.50 3.75 13.6
100 x 100 x 65 108,0 x 108,0 x 73,0 266,7 95,3 6.2
108,0mm x 108,0mm x 76,1mm 4.252 x 4.252 x 3.000 10.50 3.75 12.6
100 x 100 x 65 108,0 x 108,0 x 76,1 266,7 95,3 5,7
108,0mm x 108,0mm x 3 4.252 x 4.252 x 3.500 10.50 3.75 14.6
100 x 100 x 80 108,0 x 108,0 x 88,9 266,7 95,3 6,6
4x4x2 4.500 x 4.500 x 2.375 10.50 3.75 14.5
100 x 100 x 50 114,3 x 114,3 x 60,3 266,7 95,3 6,6
4 x 4 x 2-1/2 4.500 x 4.500 x 2.874 10.50 3.75 15.7
100 x 100 x 65 114,3 x 114,3 x 73,0 266,7 95,3 7,1
4 x 4 x 76,1mm 4.500 x 4.500 x 3.000 10.50 3.75 14.7
100 x 100 x 65 114,3 x 114,3 x 76,1 266,7 95,3 6,7
4x4x3 4.500 x 4.500 x 3.500 10.50 3.75 16.6
100 x 100 x 80 114,3 x 114,3 x 88,9 266,7 95,3 7,5
133,0mm x 133,0mm x 2 5.250 x 5.250 x 2.375 12.50 4.00 13.8
C to LE 1225 x 125 x 50 133,0 x 133,0 x 60,3 317,5 102,0 6,3
133,0mm x 133,0mm x 2-1/2 5.250 x 5.250 x 2.874 12.50 4.00 15.3
C to LE 125 x 125 x 65 133,0 x 133,0 x 73,0 317,5 102,0 6,9
C to SE
133,0mm x 133,0mm x 76,1mm 5.250 x 5.250 x 2.874 12.50 4.00 14.2
125 x 125 x 65 133,0 x 133,0 x 76,1 317,5 102,0 6,4
133,0mm x 133,0mm x 3 5.250 x 5.250 x 3.500 12.50 4.00 16.6
1225 x 125 x 80 133,0 x 133,0 x 88,9 317,5 102,0 7,5
133,0mm x 133,0mm x 4 5.250 x 5.250 x 4.500 12.50 4.00 18.9
1225 x 125 x 100 133,0 x 133,0 x 114,3 317,5 102,0 8,6
139,7mm x 139,7mm x 2 5.500 x 5.500 x 2.375 12.50 4.00 17.2
125 x 125 x 50 139,7 x 139,7 x 60,3 317,5 102,0 7,8
1399mm x 139,7mm x 2-1/2 5.250 x 5.250 x 2.874 12.50 4.00 18.7
125 x 125 x 65 139,7 x 139,7 x 73,0 317,5 102,0 8,5
133,0mm x 133,0mm x 76,1mm 5.250 x 5.250 x 2.874 12.50 4.00 17.5
125 x 125 x 65 139,7 x 139,7 x 76,1 317,5 102,0 7,9
139,7mm x 139,7mm x 3 5.500 x 5.500 x 3.500 12.50 4.00 19.8
125 x 125 x 80 139,7 x 139,7 x 88,9 317,5 102,0 8,9
139,7mm x 139,7mm x 4 5.500 x 5.500 x 4.500 12.50 4.00 21.2
125 x 125 x 100 139,7 x 139,7 x 114,3 317,5 102,0 9,6
5x5x2 5.563 x 5.563 x 2.375 12.50 4.00 21.7
125 x 125 x 50 141,3 x 141,3 x 60,3 317,5 101,6 9,8
5 x 5 x 2-1/2 5.563 x 5.563 x 2.874 12.50 4.00 23.2
125 x 125 x 65 141,3 x 141,3 x 73,0 317,5 101,6 10,5
5 x 5 x 76,1mm 5.563 x 5.563 x 3.000 12.50 4.00 22.0
125 x 125 x 65 141,3 x 141,3 x 76,1 317,5 101,6 9,9
5x5x3 5.563 x 5.563 x 3.500 12.50 4.00 24.2
125 x 125 x 80 141,3 x 141,3 x 88,9 317,5 101,6 11,0
5x5x4 5.563 x 5.563 x 4.500 12.50 4.00 26.2
125 x 125 x 100 141,3 x 141,3 x 114,3 317,5 101,6 11,8
159,0mm x 159,0mm x 2 6.250 x 6.250 x 2.375 14.00 4.50 19.8
150 x 150 x 50 159,0 x 159,0 x 60,3 355,6 114,0 8,9
TABLE 15 (1 OF 4)
FIGURE 325 FABRICATED 45° REDUCING LATERALS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 29 of 64

Nominal Pipe Size

C to LE C to SE Weight
O.D. Inches Inches Lbs.
ANSI Inches mm mm kg
Inches
DN mm
159,0mm x 159,0mm x 76,1mm 6.250 x 6.250 x 3.000 14.00 4.50 20.2
150 x 150 x 65 159,0 x 159,0 x 76,1 355,6 114,0 9,1
159,0mm x 159,0mm x 3 6.250 x 6.250 x 3.500 14.00 4.50 22.8
150 x 150 x 80 159,0 x 159,0 x 88,9 355,6 114,0 10,3
159,0mm x 159,0mm x 4 6.250 x 6.250 x 4.500 14.00 4.50 25.2
150 x 150 x 100 159,0 x 159,0 x 114,3 355,6 114,0 11,4
159,0mm x 159,0mm x 133mm 6.250 x 6.250 x 5.250 14.00 4.50 23.0
150 x 150 x 125 159,0 x 159,0 x 133,0 355,6 114,0 10,4
159,0mm x 159,0mm x 139,7mm 6.250 x 6.250 x 5.500 14.00 4.50 25.2
150 x 150 x 125 159,0 x 159,0 x 139,7 355,6 114,0 11,4
165,1mm x 165,1mm x 2 6.500 x 6.500 x 2.375 14.00 4.50 22.4
150 x 150 x 50 165,1 x 165,1 x 60,3 355,6 114,0 10,2
165,1mm x 165,1mm x 76,1mm 6.500 x 6.500 x 3.000 14.00 4.50 22.8
150 x 150 x 65 165,1 x 165,1 x 76,1 355,6 114,0 10,3
165,1mm x 165,1mm x 3 6.500 x 6.500 x 3.500 14.00 4.50 25.3
150 x 150 x 80 165,1 x 165,1 x 88,9 355,6 114,0 11,5
165,1mm x 165,1mm x 4 6.500 x 6.500 x 4.500 14.00 4.50 27.6
150 x 150 x 100 165,1 x 165,1 x 114,3 355,6 114,0 12,5
165,1mm x 165,1mm x 133,0mm 6.50 x 6.500 x 5.250 14.00 4.50 25.3
150 x 150 x 125 165,1 x 165,1 x 133,0 355,6 114,0 11,5
165,1mm x 165,1mm x 139,7mm 6.500 x 6.500 x 5.500 14.00 4.50 27.5
150 x 150 x 125 165,1 x 165,1 x 139,7 355,6 114,0 12,5
6x6x2 6.625 x 6.625 x 2.375 14.00 4.50 31.0
150 x 150 x 50 168,3 x 168,3 x 60,3 355,6 114,3 14,1 C to LE
6 x 6 x 2-1/2 6.625 x 6.625 x 2.874 14.00 4.50 32.5
150 x 150 x 65 168,3 x 168,3 x 73,0 355,6 114,3 14,7 C to LE
C to SE
6 x 6 x 76,1mm 6.625 x 6.625 x 3.000 14.00 4.50 31.2
150 x 150 x 65 168,3 x 168,3 x 76,1 355,6 114,3 14,2
6x6x3 6.625 x 6.625 x 3.500 14.00 4.50 33.6
150 x 150 x 80 168,3 x 168,3 x 88,9 355,6 114,3 15,2
6x6x4 6.625 x 6.625 x 4.500 14.00 4.50 35.7
150 x 150 x 100 168,3 x 168,3 x 114,3 355,6 114,3 16,2
6 x 6 x 139,7mm 6.625 x 6.625 x 5.500 14.00 4.50 35.2
150 x 150 x 125 168,3 x 168,3 x 139,7 356,0 114,0 15,9
6x6x5 6.625 x 6.625 x 5.563 14.00 4.50 38.2
150 x 150 x 125 168,3 x 168,3 x 141,3 355,6 114,3 17,3
216,3mm x 216,3mm x 4 8.516 x 8.516 x 4.500 18.00 6.00 49.2
200 x 200 x 100 216,3 x 216,3 x 114,3 457,2 152,4 22,3
216,3mm x 216,3mm x 139,7mm 8.516 x 8.516 x 5.500 18.00 6.00 49.0
200 x 200 x 125 216,3 x 216,3 x 139,7 457,2 152,4 22,2
216,3mm x 216,3mm x 5 8.516 x 8.516 x 5.563 18.00 6.00 52.7
200 x 200 x 125 216,3 x 216,3 x 141,3 457,2 152,4 23,9
216,3mm x 216,3mm x 165,1mm 8.516 x 8.516 x 6.500 18.00 6.00 50.6
200 x 200 x 150 216,3 x 216,3 x 165,1 457,2 152,4 22,9
216,3mm x 216,3mm x 6 8.516 x 8.516 x 6.625 18.00 6.00 56.8
200 x 200 x 150 216,3 x 216,3 x 168,3 457,2 152,4 25,7
8x8x4 8.625 x 8.625 x 4.50 18.00 6.00 65.1
200 x 200 x 100 219,1 x 219,1 x 114,1 457,2 152,4 29,5
8 x 8 x 139,7mm 8.625 x 8.625 x 5.500 18.00 6.00 64.6
200 x 200 x 125 219,1 x 219,1 x 139,7 457,0 152,0 29.3
8x8x5 8.625 x 8.625 x 6.500 18.00 6.00 68.3
200 x 200 x 125 219,1 x 219,1 x 165,1 457,2 152,4 30.9
8 x 8 x 165,1mm 8.625 x 8.625 x 6.625 18.00 6.00 65.8
200 x 200 x 150 219,1 x 219,1 x 168,3 457,2 152,4 29,8
TABLE 15 (2 OF 4)
FIGURE 325 FABRICATED 45° REDUCING LATERALS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 30 of 64

Nominal Pipe Size

C to LE C to SE Weight
O.D. Inches Inches Lbs.
ANSI Inches mm mm kg
Inches
DN mm
8x8x6 8.625 x 8.625 x 6.625 18.00 6.00 72.0
200 x 200 x 150 219,1 x 219,1 x 168,3 457,2 152,4 32,6
267,4mm x 267,4mm x 4 10.528 x 10.528 x 4.500 20.50 6.50 73.3
250 x 250 x 100 267,4 x 267,4 x 114,3 520,7 165,1 33.2
267,4mm x 267,4mm x 139,7mm 10.528 x 10.528 x 5.500 20.50 6.50 73.0
250 x 250 x 125 267,4 x 267,4 x 139,7 520,7 165,1 33,1
267,4mm x 267,4mm x 5 10.528 x 10.528 x 5.563 20.50 6.50 77.0
250 x 250 x 125 267,4 x 267,4 x 141,3 520,7 165,1 34,9
267,4mm x 267,4mm x 165,1mm 10.528 x 10.528 x 6.500 20.50 6.50 74.6
250 x 250 x 150 267,4 x 267,4 x 165,1 520,7 165,1 33,8
267,4mm x 267,4mm x 6 10.528 x 10.528 x 6.625 20.50 6.50 81.2
250 x 250 x 150 267,4 x 267,4 x 168,3 520,7 165,1 36,8
267,4mm x 267,4mm x 216,3mm 10.528 x 10.528 x 8.516 20.50 6.50 80.8
250 x 250 x 200 267,4 x 267,4 x 216,3 520,7 165,1 36,6
267,4mm x 267,4mm x 8 10.528 x 10.528 x 8.625 20.50 6.50 91.0
250 x 250 x 200 267,4 x 267,4 x 219,1 520,7 165,1 41,3
10 x 10 x 4 10.750 x 10.750 x 4.500 20.50 6.50 99.2
250 x 250 x 100 273,0 x 273,0 x 114,3 520,7 165,1 45,0
10 x 10 x 139,7mm 10.750 x 10.750 x 5.500 20.50 6.50 98.5
250 x 250 x 125 273,0 x 273,0 x 139,7 521,0 165,0 44,7
10 x 10 x 5 10.750 x 10.750 x 5.563 20.50 6.50 102.4
250 x 250 x 125 273,0 x 273,0 x 141,3 520,7 165,1 46,4
10 x 10 x 165,1mm 10.750 x 10.750 x 6.500 20.50 6.50 99.7
C to LE 250 x 250 x 150 273,0 x 273,0 x 165,1 520,7 165,1 45,2
10 x 10 x 6 10.750 x 10.750 x 6.625 20.50 6.50 106.2
C to LE 250 x 250 x 150 273,0 x 273,0 x 168,3 520,7 165,1 48,2
C to SE
10 x 10 x 216,3mm 10.750 x 10.750 x 8.516 20.50 6.50 104.7
250 x 250 x 200 273,0 x 273,0 x 216,3 520,7 165,1 47,5
10 x 10 x 8 10.750 x 10.750 x 8.625 20.50 6.50 114.7
250 x 250 x 200 273,0 x 273,0 x 219,1 520,7 165,1 52,0
318,5mm x 318,5mm x 4 12.539 x 12.539 x 4.500 23.00 7.00 98.7
300 x 300 x 100 318,5 x 318,5 x 114,3 584,2 177,8 44,8
318,5mm x 318,5mm x 165,1mm 12.539 x 12.539 x 6.500 23.00 7.00 100.1
300 x 300 x 150 318,5 x 318,5 x 165,1 584,2 177,8 45,4
318,5mm x 318,5mm x 6 12.539 x 12.539 x 6.625 23.00 7.00 107.3
300 x 300 x 150 318,5 x 318,5 x 168,3 584,2 177,8 48,7
318,5mm x 318,5mm x 216,3mm 12.539 x 12.539 x 8.516 23.00 7.00 106.6
300 x 300 x 200 318,5 x 318,5 x 2196,3 584,2 177,8 48,4
318,5mm x 318,5mm x 8 12.539 x 12.539 x 8.625 23.00 7.00 117.3
300 x 300 x 200 318,5 x 318,5 x 219,1 584,2 177,8 53,2
318,5mm x 318,5mm x 267,4mm 12.539 x 12.539 x 10.528 23.00 7.00 115.0
300 x 300 x 250 318,5 x 318,5 x 267,4 584,2 177,8 52,2
318,5mm x 318,5mm x 10 12.539 x 12.539 x 10.750 23.00 7.00 131.0
300 x 300 x 250 318,5 x 318,5 x 273,0 584,2 177,8 59,4
12 x 12 x 4 12.750 x 12.750 x 4.500 23.00 7.00 132.4
300 x 300 x 100 323,9 x 323,9 x 114,3 584,2 177,8 60,1
12 x 12 x 165,1mm 12.750 x 12.750 x 6.500 23.00 7.00 133.0
300 x 300 x 150 323,9 x 323,9 x 165,1 584,2 177,8 60,3
12 x 12 x 6 12.750 x 12.750 x 6.625 23.00 7.00 140.0
300 x 300 x 150 323,9 x 323,9 x 168,3 584,2 177,8 63,5
12 x 12 x 216,3mm 12.750 x 12.750 x 8.516 23.00 7.00 138.0
300 x 300 x 200 323,9 x 323,9 x 216,3 584,2 177,8 62,6
TABLE 15 (3 OF 4)
FIGURE 325 FABRICATED 45° REDUCING LATERALS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 31 of 64

Nominal Pipe Size

C to LE C to SE Weight
O.D. Inches Inches Lbs.
ANSI Inches mm mm kg
Inches
DN mm
12 x 12 x 8 12.750 x 12.750 x 8.625 23.00 7.00 150.0
300 x 300 x 200 323,9 x 323,9 x 219,1 584,2 177,8 68.0
12 x 12 x 267,4mm 12.750 x 12.750 x 10.528 23.00 7.00 145.3
300 x 300 x 250 323,9 x 323,9 x 267,4 584,2 177,8 65,9
12 x 12 x 10 12.750 x 12.750 x 10.750 23.00 7.00 161.0
300 x 300 x 250 323,9 x 323,9 x 273,0 584,2 177,8 73,0
14 x 14 x 4 14.000 x 14.000 x 4.500 26.50 7.50 165.0
350 x 350 x 100 355,6 x 355,6 x 114,3 673,1 190,5 74,8
14 x 14 x 6 14.000 x 14.000 x 6.625 26.50 7.50 174.5
350 x 350 x 150 355,6 x 355,6 x 168,3 673,1 190,5 79,2
14 x 14 x 8 14.000 x 14.000 x 8.625 26.50 7.50 185.6
350 x 350 x 200 355,6 x 355,6 x 219,1 673,1 190,5 84,2
14 x 14 x 267,4mm 14.000 x 14.000 x 10.528 26.50 7.50 182.0
350 x 350 x 250 355,6 x 355,6 x 267,4 673,1 190,5 82,5
14 x 14 x 10 14.000 x 14.000 x 10.750 26.50 7.50 200.0
350 x 350 x 250 355,6 x 355,6 x 273,0 673,1 190,5 90,7
14 x 14 x 318,5mm 14.000 x 14.000 x 12.539 26.50 7.50 188.0
350 x 350 x 300 355,6 x 355,6 x 318,5 673,1 190,5 85,3
14 x 14 x 12 14.000 x 14.000 x 12.750 26.50 7.50 210.0
350 x 350 x 300 355,6 x 355,6 x 323,9 673,1 190,5 95,3
16 x 16 x 6 16.000 x 16.000 x 6.625 29.00 8.00 214.1
400 x 400 x 150 406,4 x 406,4 x 168,3 736,6 203,0 97,1
16 x 16 x 8 16.000 x 16.000 x 8.625 29.00 8.00 225.9
400 x 400 x 200 406,4 x 406,4 x 219,1 736,6 203,0 102,5 C to LE
16 x 16 x 10 16.000 x 16.000 x 10.750 29.00 8.00 241.0
400 x 400 x 250 406,4 x 406,4 x 273,0 736,6 203,0 109,3 C to LE
C to SE
16 x 16 x 12 16.000 x 16.000 x 12.750 29.00 8.00 251.8
400 x 400 x 300 406,4 x 406,4 x 323,9 736,6 203,0 114,2
16 x 16 x 14 16.000 x 16.000 x 14.000 29.00 8.00 257.5
400 x 400 x 350 406,4 x 406,4 x 355,6 736,6 203,0 116,8
18 x 18 x 6 18.000 x 18.000 x 6.625 32.00 8.50 261.4
450 x 450 x 150 457,2 x 457,2 x 168,3 812,8 215,9 118,5
18 x 18 x 8 18.000 x 18.000 x 8.625 32.00 8.50 274.4
450 x 450 x 200 457,2 x 457,2 x 219,1 812,8 215,9 124,5
18 x 18 x 10 18.000 x 18.000 x 10.750 32.00 8.50 290.8
450 x 450 x 250 457,2 x 457,2 x 273,0 812,8 215,9 131,9
18 x 18 x 12 18.000 x 18.000 x 12.750 32.00 8.50 302.5
450 x 450 x 300 457,2 x 457,2 x 323,9 812,8 215,9 137,2
18 x 18 x 14 18.000 x 18.000 x 14.000 32.00 8.50 308.6
450 x 450 x 350 457,2 x 457,2 x 355,6 812,8 215,9 140,0
18 x 18 x 16 18.000 x 18.000 x 16.000 32.00 8.50 318.5
450 x 450 x 400 457,2 x 457,2 x 406,4 812,8 215,9 144,4
20 x 20 x 12 20.000 x 20.000 x 12.750 35.00 9.00 358.0
500 x 500 x 300 508,0 x 508,0 x 323,9 889,0 228,6 162,3
20 x 20 x 14 20.000 x 20.000 x 14.000 35.00 9.00 364.6
500 x 500 x 350 508,0 x 508,0 x 355,6 889,0 228,6 165,4
20 x 20 x 16 20.000 x 20.000 x 16.000 35.00 9.00 375.1
500 x 500 x 400 508,0 x 508,0 x 406,4 889,0 228,6 170,1
24 x 24 x 16 24.000 x 24.000 x 16.000 40.00 10.00 489.0
600 x 600 x 400 609,6 x 609,6 x 406,4 1016,0 254,0 221,8
24 x 24 x 20 24.000 x 24.000 x 20.000 40.00 10.00 511.5
600 x 600 x 500 609,6 x 609,6 x 508,0 1016,0 254,0 232,0
TABLE 15 (4 OF 4)
FIGURE 325 FABRICATED 45° REDUCING LATERALS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 32 of 64

Figure 251 Cast Figure 351 Fabricated

Nominal Pipe Size Eccentric Reducer Eccentric Reducer
O.D. E to E Weight E to E Weight
ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg
1-1/4 x 1 1.660 x 1.315 8.50 1.7
- -
32 x 25 42,4 x 33,7 215,9 0,8
1-1/2 x 3/4 1.900 x 1.050 8.50 1.8
- -
40 x 20 48,3 x 26,7 215,9 0,8
1-1/2 x 1 1.900 x 1.315 8.50 1.9
- -
40 x 25 48,3 x 33,4 215,9 0,9
1-1/2 x 1-1/4 1.900 x 1.660 8.50 2.2
- -
40 x 32 48,3 x 42,4 215,9 1,0
2 x 3/4 2.375 x 1,050 9.00 2.1
50 x 20 60,3 x 26,7 228,6 0,9
2x1 2.375 x 1.315 9.00 2.2
- -
50 x 25 60,3 x 33,4 228,6 1,0
2 x 1-1/4 2.375 x 1.660 9.00 2.4
- -
50 x 32 60,3 x 42,4 228,6 1,1
2 x 1-1/2 2.375 x 1.900 9.00 2.5
- -
50 x 40 60,3 x 48,3 228,6 1,1
E to E 2-1/2 x 1 2.874 x 1.315 9.50 3.2
- -
65 x 25 73,0 x 33,4 241,3 1,5
2-1/2 x 1-1/4 2.874 x 1.660 9.50 3.4
- -
65 x 32 73,0 x 42,4 241,3 1,5
2-1/2 x 1-1/2 2.874 x 1.900 9.50 3.6
FIGURE 251 - -
65 x 40 73,0 x 48,3 241,3 1,6
CAST ECCENTRIC REDUCER
2-1/2 x 2 2.874 x 2.375 9.50 4.0
- -
65 x 50 73,0 x 60,3 241,3 1,8

E to E 76,1mm x 1 3.000 x 1.315 9.50 3.7

- -
65 x 25 73, 0 x 33,4 241,3 1,7
76,1mm x 1-1/4 3.000 x 1.660 9.50 3.9
- -
65 x 32 73, 0 x 42,4 241,3 1,8
76,1mm x 1-1/2 3.000 x 1.900 9.50 4.2
- -
FIGURE 351 65 x 40 73,0 x 48,3 241,3 1,9
FABRICATED 76,1mm x 2 3.000 x 2.375 9.50 4.5
ECCENTRIC REDUCER 65 x 50 73,0 x 60,3 - - 241,3 2,0
(SEGMENT WELDED)
3x1 3.500 x 1.315 9.50 4.0
- -
80 x 25 88,9 x 33,4 241,3 1,8
3 x 1-1/4 3.500 x 1.660 9.50 4.3
- -
80 x 32 88,9 x 42,4 241,3 2,0
3 x 1-1/2 3.500 x 1.900 9.50 4.5
- -
80 x 40 88,9 x 48,3 241,3 2,0
3x2 3.500 x 2.375 3.50 2.0 9.50 4.8
80 x 50 88,9 x 60,3 88,9 0,9 241,3 2,1
3 x 2-1/2 3.500 x 2.874 3.50 2.2 9.50 5.5
80 x 65 88,9 x 73,0 88,9 1,0 241,3 2,5
3 x 76,1mm 3.500 x 3.000 9.50 5.8
- -
80 x 65 88,9 x 76,1 241,3 2,6
108,0mm x 1 4.252 x 1.315 10.00 5.9
- -
100 x 25 108,0 x 33,4 254,0 2,7
108,0mm x 1-1/4 4.252 x 1.660 10.00 6.2
- -
100 x 32 108,0 x 42,4 254,0 2,8
108,0mm x 1-1/2 4.252 x 1.900 10.00 6.5
- -
100 x 40 108,0 x 48,3 254,0 2,9
108,0mm x 2 4.252 x 2.375 10.00 6.7
- -
100 x 50 108,0 x 60,3 254,0 3,0
108,mm x 2-1/2 4.252 x 2.874 10.00 7.4
- -
100 x 65 108,0 x 73,0 254,0 3,4
TABLE 16 (1 OF 6)
FIGURES 251 AND 351 CAST AND FABRICATED ECCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 33 of 64

Figure 251 Cast Figure 351 Fabricated

Nominal Pipe Size Eccentric Reducer Eccentric Reducer
O.D. E to E Weight E to E Weight
ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg
108,0mm x 76,1mm 4.252 x 3.000 10.00 7.8
- -
100 x 65 108,0 x 76,1 254,0 3,5
4x1 4.500 x 1.315 10.00 5.9
- -
100 x 25 114,3 x 33,4 254,0 2,7
4 x 1-1/4 4.500 x 1.660 10.00 6.3
- -
100 x 32 114,3 x 42,4 254,0 2,9
4 x 1-1/2 4.500 x 1.900 10.00 6.4
- -
100 x 40 114,3 x 48,3 254,0 2,9
4x2 4.500 x 2.375 4.00 3.0 10.00 6.9
100 x 50 114,3 x 60,3 101,6 1,4 254,0 3,1
4 x 2-1/2 4.500 x 2.874 4.00 3.0 10.00 7.5
100 x 65 114,3 x 73,0 101,6 1,4 254,0 3,4
4 x 76,1mm 4.500 x 3.000 10.00 7.7
- -
100 x 65 114,3 x 76,1 254,0 3,5
4x3 4.500 x 3.500 4.00 3.3 10.00 7.9
100 x 80 114,3 x 88,9 101,6 1,5 254,0 3,6
133,0mm x 2 5.250 x 2.375 11.00 8.5 E to E
- -
125 x 50 133,0 x 60,3 279,4 3,9
133,0mm x 2-1/2 5.250 x 2.874 11.00 9.0
- -
125 x 65 133,0 x 73,0 279,4 4,1
133,0mm x 76,1mm 5.250 x 3.000 11.00 9.3
- - FIGURE 251
125 x 65 133,0 x 76,1 279,4 4,2
CAST ECCENTRIC REDUCER
133,0mm x 3 5.250 x 3.500 11.00 10.4
- -
125 x 80 133,0 x 88,9 279,4 4,7
133,0mm x 108,0mm 5.250 x 4.252 11.00 11.0 E to E
- -
125 x 100 133,0 x 108,0 279,4 5.0
139,7mm x 2 5.500 x 2.375 11.00 9.0
- -
125 x 50 139,7 x 60,3 279,4 4,1
139,7mm x 2-1/2 5.500 x 2.874 11.00 9.5
- -
125 x 65 139,7 x 73,0 279,4 4,3 FIGURE 351
139,7mm x 76,1mm 5.500 x 3.000 11.00 9.8 FABRICATED
125 x 65 139,7 x 76,1 - - 279,4 4,4 ECCENTRIC REDUCER
(SEGMENT WELDED)
139,7mm x 3 5.500 x 3.500 11.00 10.8
- -
125 x 80 139,7 x 88,9 279,4 4,9
139,7mm x 108,0mm 5.500 x 4.252 11.00 10.6
- -
125 x 100 139,7 x 108,0 279,4 4,8
5x2 5.563 x 2.375 11.00 9.3
- -
125 x 50 141,3 x 60,3 279,4 4,2
5 x 2-1/2 5.563 x 2.874 11.00 9.9
- -
125 x 65 141,3 x 73,0 279,4 4,5
5 x 76,1mm 5.563 x 3.000 11.00 10.2
- -
125 x 65 141,3 x 76,1 279,4 4,6
5x3 5.563 x 3.500 11.00 10.7
- -
125 x 80 141,3 x 88,9 279,4 4,9
5 x 108,0mm 5.563 x 4.252 11.00 11.5
- -
125 x 100 141,3 x 108,0 279,4 5,2
5x4 5.563 x 4.500 5.00 5.7 11.00 11.9
125 x 100 141,3 x 114,3 127,5 2,6 279,4 5,4
159,0mm x 2 6.250 x 2.375 11.50 11.5
- -
150 x 50 159,0 x 60,3 292,1 5,2
159,0mm x 2-1/2 6.250 x 2.874 11.50 12.0
- -
150 x 65 159,0 x 73,0 292,1 5,4
159,0mm x 76,1mm 6.250 x 3.000 11.50 12.3
- -
150 x 65 159,0 x 76,1 292,1 5,6
TABLE 16 (2 OF 6)
FIGURES 251 AND 351 CAST AND FABRICATED ECCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 34 of 64

Figure 251 Cast Figure 351 Fabricated

Nominal Pipe Size Eccentric Reducer Eccentric Reducer
O.D. E to E Weight E to E Weight
ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg
159,0mm x 3 6.250 x 3.500 11.50 13.0
- -
150 x 80 159,0 x 88,9 292,1 5,9
159,0mm x 108,0mm 6.250 x 4.252 11.50 13.5
- -
150 x 100 159,0 x 108,0 292,1 6,1
159,0mm x 4 6.250 x 4.500 11.50 13.8
- -
150 x 100 159,0 x 114,3 292,1 6,3
159,0mm x 133,0mm 6.250 x 5.250 11.50 14.2
- -
150 x 125 159,0 x 133,0 292,1 6,4
159,0mm x 139,7mm 6.250 x 5.500 11.50 14.8
- -
150 x 125 159,0 x 139,7 292,1 6,7
165,1mm x 2 6.500 x 2.375 11.50 11.8
- -
150 x 50 165,1 x 60,3 292,1 5,4
165,1mm x 2-1/2 6.500 x 2.874 11.50 12.4
- -
150 x 65 165,1 x 73,0 292,1 5,6
165,1mm x 76,1mm 6.500 x 3.000 11.50 12.7
- -
150 x 65 165,1 x 76,1 292,1 5,8
E to E 165,1mm x 3 6.500 x 3.500 11.50 13.3
- -
150 x 80 165,1 x 88,9 292,1 6,0
165,1mm x 108,0mm 6.500 x 4.252 11.50 13.8
- -
150 x 100 165,1 x 108,0 292,1 6,3
165,1mm x 4 6.500 x 4.500 11.50 14.1
FIGURE 251 - -
150 x 100 165,1 x 114,3 292,1 6,4
CAST ECCENTRIC REDUCER
165,1mm x 133,0mm 6.500 x 5.250 11.50 14.6
- -
150 x 125 165,1 x 133,0 292,1 6,6

E to E 165,1mm x 139,7mm 6.500 x 5.500 11.50 15.0

- -
150 x 125 165,1 x 139,7 292,1 6,8
165,1mm x 5 6.500 x 5.563 11.50 15.8
- -
150 x 125 165,1 x 141,3 292,1 7,2
6x2 6.625 x 2.375 11.50 12.2
- -
FIGURE 351 150 x 50 168,3 x 60,3 292,1 5,5
FABRICATED 6 x 2-1/2 6.625 x 2.874 11.50 12.8
ECCENTRIC REDUCER 150 x 65 168,3 x 73,0 - - 292,1 5,8
(SEGMENT WELDED)
6 x 76,1mm 6.625 x 3.000 11.50 13.0
- -
150 x 65 168,3 x 76,1 292,1 5,9
6x3 6.625 x 3.500 5.50 7.4 11.50 13.5
150 x 80 168,3 x 88,9 139,7 3,4 292,1 6,1
6 x 108,0mm 6.625 x 4.252 11.50 14.1
- -
150 x 100 168,3 x 108,0 292,1 6,4
6x4 6.625 x 4.500 5.50 7.5 11.50 14.8
150 x 100 168,3 x 114,3 139,7 3,4 292,1 6,7
6 x 133,0mm 6.625 x 5.250 11.50 15.2
- -
150 x 125 168,3 x 133,0 292,1 6,9
6 x 139,7mm 6.625 x 5.500 11.50 15.7
- -
150 x 125 168,3 x 139,7 292,1 7,1
6x5 6.625 x 5.563 5.50 8.1 11.50 16.0
150 x 125 168,3 x 141,3 139,7 3,7 292,1 7,3
216,3mm x 3 8.516 x 3.500 12.00 17.2
- -
200 x 80 216,3 x 88,9 304,8 7,8
216,3mm x 108,0mm 8.516 x 4.252 12.00 18.0
- -
200 x 100 216,3 x 108,0 304,8 8,2
216,3mm x 4 8.516 x 4.500 12.00 18.7
- -
200 x 100 216,3 x 114,3 304,8 8,5
216,3mm x 133,0mm 8.516 x 5.250 12.00 19.2
- -
200 x 125 216,3 x 133,0 304,8 8,7
TABLE 16 (3 OF 6)
FIGURES 251 AND 351 CAST AND FABRICATED ECCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 35 of 64

Figure 251 Cast Figure 351 Fabricated

Nominal Pipe Size Eccentric Reducer Eccentric Reducer
O.D. E to E Weight E to E Weight
ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg
216,3mm x 139,7mm 8.516 x 5.500 12.00 20.1
- -
200 x 125 216,3 x 139,7 304,8 9,1
216,3mm x 5 8.516 x 5.563 12.00 20.8
- -
200 x 125 216,3 x 141,3 304,8 9,4
216,3mm x 159,0mm 8.516 x 6.250 12.00 21.2
- -
200 x 150 216,3 x 159,0 304,8 9,6
216,3mm x 165,1mm 8.516 x 6.500 12.00 22.6
- -
200 x 150 216,3 x 165,1 304,8 10,3
216,3mm x 6 8.516 x 6.625 12.00 23.0
- -
200 x 150 216,3 x 168,3 304,8 10,4
8x3 8.625 x 3.500 12.00 17.9
- -
200 x 80 219,1 x 88,9 304,8 8,1
8 x 108,0mm 8.625 x 4.252 12.00 18.7
- -
200 x 100 219,1 x 108,0 304,8 8,5
8x4 8.625 x 4.500 12.00 19.4
- -
200 x 100 219,1 x 114,3 304,8 8,8
8 x 133,0mm 8.625 x 5.250 12.00 19.8 E to E
- -
200 x 125 219,1 x 133,0 304,8 8,9
8 x 139,7mm 8.625 x 5.500 12.00 21.0
- -
200 x 125 219,1 x 139,7 304,8 9,5
8x5 8.625 x 5.563 12.00 21.4
- - FIGURE 251
200 x 125 219,1 x 141,3 304,8 9,7
CAST ECCENTRIC REDUCER
8 x 159,0mm 8.625 x 6.250 12.00 21.8
- -
200 x 150 219,1 x 159,0 304,8 9,8
8 x 165,1mm 8.625 x 6.500 12.00 22.8 E to E
- -
200 x 150 219,1 x 165,1 304,8 10,3
8x6 8.625 x 6.625 12.00 23.2
- -
200 x 150 219,1 x 168,3 304,8 10,5
267,4mm x 4 10.528 x 4.500 13.00 27.4
- -
250 x 100 267,4 x 114,3 330,2 12,4 FIGURE 351
267,4mm x 133,0mm 10.528 x 5.250 13.00 28.6 FABRICATED
250 x 125 267,4 x 133,0 - - 330,2 12,9 ECCENTRIC REDUCER
(SEGMENT WELDED)
267,4mm x 139,7mm 10.528 x 5.500 13.00 30.2
- -
250 x 125 267,4 x 139,7 330,2 13,7
267,4mm x 5 10.528 x 5.563 13.00 31.0
- -
250 x 125 267,4 x 141,3 330,2 14,1
267,4mm x 159,0mm 10.528 x 6.250 13.00 32.1
- -
250 x 150 267,4 x 159,0 330,2 14,6
267,4mm x 165,1mm 10.528 x 6.500 13.00 33.0
- -
250 x 150 267,4 x 165,1 330,2 14,9
267,4mm x 6 10.528 x 6.625 13.00 33.5
- -
250 x 150 267,4 x 168,3 330,2 15,2
267,4mm x 8 10.528 x 8.625 13.00 34.0
- -
250 x 200 267,4 x 219,1 300,2 15,4
10 x 4 10.750 x 4.500 13.00 29.7
- -
250 x 100 273,0 x 114,3 330,2 13,5
10 x 133,0mm 10.750 x 5.250 13.00 30.0
- -
250 x 125 273,0 x 133,0 330,2 13,6
10 x 139,7mm 10.750 x 5.500 13.00 30.8
- -
250 x 125 273,0 x 139,7 330,2 13,9
10 x 5 10.750 x 5.563 13.00 31.7
- -
250 x 125 273,0 x 141,3 330,2 14,4
10 x 159,0mm 10.750 x 6.250 13.00 32.7
- -
250 x 150 273,0 x 159,0 330,2 14,8
TABLE 16 (4 OF 6)
FIGURES 251 AND 351 CAST AND FABRICATED ECCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 36 of 64

Figure 251 Cast Figure 351 Fabricated

Nominal Pipe Size Eccentric Reducer Eccentric Reducer
O.D. E to E Weight E to E Weight
ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg
10 x 165,1mm 10.750 x 6.500 13.00 33.3
- -
250 x 150 273,0 x 165,1 330,2 15,1
10 x 6 10.750 x 6.625 13.00 34.0
- -
250 x 150 273,0 x 168,3 330,2 15,4
10 x 216,3mm 10.750 x 8.516 13.00 34.2
- -
250 x 200 273,0 x 216,3 330,2 15,5
10 x 8 10.750 x 8.625 13.00 34.4
- -
250 x 200 273,0 x 219,1 330,2 15,6
318,5mm x 4 12.539 x 4.500 14.00 40.1
- -
300 x 100 318,5 x 114,3 355,6 18,2
318,5mm x 133,0mm 12.539 x 5.250 14.00 41.7
- -
300 x 125 318,5 x 133,0 355,6 18,9
318,5mm x 139,7mm 12.539 x 5.500 14.00 42.0
- -
300 x 125 318,5 x 139,7 355,6 19,1
318,5mm x 5 12.539 x 5.563 14.00 42.7
- -
300 x 125 318,5 x 141,3 355,6 19,3
E to E 318,5mm x 159,0mm 12.539 x 6.250 14.00 43.4
- -
300 x 150 318,5 x 159,0 355,6 19,6
318,5mm x 165,1mm 12.539 x 6.500 14.00 44.6
- -
300 x 150 318,5 x 165,1 355,6 20,2
318,5mm x 6 12.539 x 6.625 14.00 45.0
FIGURE 251 - -
300 x 150 318,5 x 168,3 355,6 20,4
CAST ECCENTRIC REDUCER
318,5mm x 216,3mm 12.539 x 8.516 14.00 47.6
- -
300 x 200 318,5 x 216,3 355,6 21,6

E to E 318,5mm x 8 12.539 x 8.625 14.00 48.0

- -
300 x 200 318,5 x 219,1 355,6 21,7
318,5mm x 267,4mm 12.539 x 10.528 14.00 49.1
- -
300 x 250 318,5 x 267,4 355,6 22.2
318,5mm x 10 12.539 x 10.750 14.00 50.8
- -
FIGURE 351 300 x 250 318,5 x 273,0 355,6 23.0
FABRICATED 12 x 4 12.75 x 4.500 14.00 41.9
ECCENTRIC REDUCER 300 x 100 323,9 x 114,3 - - 355,6 19.0
(SEGMENT WELDED)
12 x 133,0mm 12.750 x 5.250 14.00 42.2
- -
300 x 125 323,9 x 133,0 355,6 19,1
12 x 139,7mm 12.750 x 5.500 14.00 43.4
- -
300 x 125 323,9 x 139,7 355,6 19,7
12 x 5 12.750 x 5.563 14.00 44.0
- -
300 x 125 323,9 x 141,3 355,6 20.0
12 x 159,0mm 12.750 x 6.250 14.00 44.3
- -
300 x 150 323,9 x 159,0 355,6 20,1
12 x 165,1mm 12.750 x 6.500 14.00 44.7
- -
300 x 150 323,9 x 165,1 355,6 20,3
12 x 6 12.750 x 6.625 14.00 45.2
- -
300 x 150 323,9 x 168,3 355,6 20,5
12 x 216,3mm 12.750 x 8.516 14.00 46.3
- -
300 x 200 323,9 x 216,3 355,6 21,0
12 x 8 12.750 x 8.625 14.00 47.7
- -
300 x 200 323,9 x 219,1 355,6 21,6
12 x 267,4mm 12.750 x 10.528 14.00 48.9
- -
300 x 250 323,9 x 267,4 355,6 22,2
12 x 10 12.750 x 10.750 14.00 52.0
- -
300 x 250 323,9 x 273,0 355,6 23,6
14 x 6 14.000 x 6.625 19.00 78.0
- -
350 x 150 355,6 x 168,3 482,6 35,4
TABLE 16 (5 OF 6)
FIGURES 251 AND 351 CAST AND FABRICATED ECCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 37 of 64

Figure 251 Cast Figure 351 Fabricated

Nominal Pipe Size Eccentric Reducer Eccentric Reducer
O.D. E to E Weight E to E Weight
ANSI Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg
14 x 216,3mm 14.000 x 8.516 19.00 79.1
- -
350 x 200 355,6 x 216,3 482,6 35,9
14 x 8 14.000 x 8.625 19.00 80.0
- -
350 x 200 355,6 x 219,1 482,6 36,3
14 x 267,4mm 14.000 x 10.528 19.00 82.5
- -
350 x 250 355,6 x 267,4 482,6 37,4
14 x 10 14.000 x 10.750 19.00 84.0
- -
350 x 250 355,6 x 273,0 482,6 38,1
14 x 318,5mm 14.000 x 12.539 19.00 86.3
- -
350 x 300 355,6 x 318,5 482,6 39,1
14 x 12 14.000 x 12.750 19.00 88.0
- -
350 x 300 355,6 x 323,9 482,6 39,9
16 x 8 16.000 x 8.625 20.00 91.0
- -
400 x 200 406,4 x 219,1 508,0 41,3
16 x 267,4mm 16.000 x 10.528 20.00 94.5
- -
400 x 250 406,4 x 267,4 508,0 42,9
16 x 10 16.000 x 10.750 20.00 96.0 E to E
- -
400 x 250 406,4 x 273,0 508,0 43,5
16 x 318,5mm 16.000 x 12.539 20.00 98.1
- -
400 x 300 406,4 x 318,5 508,0 44,5
16 x 12 16.000 x 12.750 20.00 99.0
- - FIGURE 251
400 x 300 406,4 x 323,9 508,0 44,9
CAST ECCENTRIC REDUCER
16 x 14 16.000 x 14.000 20.00 104.0
- -
400 x 350 406,4 x 355,6 508,0 47,2
18 x 318,5mm 18.000 x 12.539 21.00 110.6 E to E
- -
450 x 300 457,2 x 318,5 533,0 50,2
18 x 12 18.000 x 12.750 21.00 113.0
- -
450 x 300 457,2 x 323,9 533,0 51,3
18 x 14 18.000 x 14.000 21.00 117.0
- -
450 x 350 457,2 x 355,6 533,0 53,1 FIGURE 351
18 x 16 18.000 x 16.000 21.00 121.0 FABRICATED
450 x 400 457,2 x 406,4 - - 533,0 54,9 ECCENTRIC REDUCER
(SEGMENT WELDED)
20 x 10 20.000 x 10.750 26.00 146.2
508 x 254 508,0 x 273,0 660,4 66,3
20 x 12 20.000 x 12.750 26.00 149.0
- -
500 x 300 508,0 x 323,9 660,4 67,6
20 x 14 20.000 x 14.000 26.00 152.0
- -
500 x 350 508,0 x 355,6 660,4 68,9
20 x 16 20.000 x 16.000 26.00 156.0
- -
500 x 400 508,0 x 406,4 660,4 70,8
20 x 18 20.000 x 18.000 26.00 160.0
- -
500 x 450 508,0 x 457,2 660,4 72,6
24 x 10 24.000 x 10.750 26.00 147.0
- -
600 x 250 609,6 x 273,0 660,4 78,9
24 x 12 24.000 x 12.750 26.00 179.0
- -
600 x 300 609,6 x 323,9 660,4 81,2
24 x 14 24.000 x 14.000 26.00 184.0
- -
600 x 350 609,6 x 355,6 660,4 83,5
24 x 16 24.000 x 16.000 26.00 189.0
- -
600 x 400 609,6 x 406,4 660,4 85,7
24 x 18 24.000 x 18.000 26.00 194.0
- -
600 x 450 609,6 x 457,2 660,4 88,0
24 x 20 24.000 x 20.000 26.00 199.0
- -
600 x 500 609,6 x 508,0 660,4 90,3
TABLE 16 (6 OF 6)
FIGURES 251 AND 351 CAST AND FABRICATED ECCENTRIC REDUCERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 38 of 64

E1

H
E2

Nominal Pipe Size

H E1 E2 Weight
O.D. Inches Inches Inches Lbs.
ANSI Inches mm mm mm kg
Inches
DN mm
2x2x2 2.375 x 2.375 x 2.375 9.75 9.00 7.37 5.7
50 x 50 x 50 60,3 x 60,3 x 60,3 247,7 228,6 187,2 2,6
2-1/2 x 2-1/2 x 2-1/2 2.874 x 2.874 x 2.874 10.75 10.50 8.88 10.2
65 x 65 x 65 73,0 x 73,0 x 73,0 273,1 266,7 225,6 4,6
76,1mm x 76,1mm x 2-1/2 3.000 x 3.000 x 3.000 10.75 10.50 8.88 10.8
65 x 65 x 65 76,1 x 76,1 x 76,1 273,1 266,7 225,6 4,9
3 x 3 x 76,1mm 3.500 x 3.500 x 3.000 11.75 11.50 9.31 13.5
80 x 80 x 65 88,9 x 88,9 x 76,1 298,5 292,1 236,5 6,1
3x3x3 3.500 x 3.500 x 3.500 11.75 11.50 9.31 14.4
80 x 80 x 80 88,9 x 88,9 x 88,9 298,5 292,1 236,5 6,5
108,0mm x 108,0mm x 76,1mm 4.252 x 4.252 x 3.000 14.25 12.88 10.19 19.8
100 x 100 x 65 108,0 x 108,0, x 76,1 362,0 327,2 258,8 8,9
108,0mm x 108,0mm x 3 4.252 x 4.252 x 3.500 14.25 12.88 10.19 20.0
100 x 100 x 80 108,0 x 108,0, x 88,9 362,0 327,2 258,8 9,1
108,0mm x 108,0mm x 108,0mm 4.252 x 4.252 x 4.500 14.25 13.63 11.87 23.6
100 x 100 x 100 108,0 x 108,0, x 108,0 362,0 346,2 301,5 10,7
4x4x3 4.500 x 4.500 x 3.500 14.25 12.88 10.19 20.5
100 x 100 x 80 114,3 x 114,3 x 88,9 362,0 327,2 258,8 9,3
4x4x4 4.500 x 4.500 x 4.500 14.25 13.63 11.87 24.6
100 x 100 x 100 114,3 x 114,3 x 114,3 362.0 346,2 301,5 11,2
133,0mm x 133,0mm x 3 5.250 x 5.250 x 3.500 16.50 14.25 13.25 25.8
125 x 125 x 80 133,0 x 133,0 x 88,9 419,1 362,0 336,6 11,7
133,0mm x 133,0mm x 108,0mm 5.250 x 5.250 x 4.252 16.50 15.13 13.63 27.2
125 x 125 x 100 133,0 x 133,0 x 108,0 419,1 384,3 346,1 12,3
133,0mm x 133,0mm x 4 5.250 x 5.250 x 4.500 16.50 15.13 13.63 30.5
125 x 125 x 100 133,0 x 133,0 x 114,3 419,1 384,3 346,1 13,8
139,7mm x 139,7mm x 3 5.500 x 5.500 x 3.500 16.50 14.25 13.25 26.4
125 x 125 x 80 139,7 x 139,7 x 88,9 419,1 362,0 336,6 11,9
139,7mm x 139,7mm x 108,0mm 5.500 x 5.500 x 4.252 16.50 15.13 13.63 31.0
125 x 125 x 100 139,7 x 139,7 x 108,0 419,1 384,3 346,1 14,1
139,7mm x 139,7mm x 4 5.500 x 5.500 x 4.500 16.50 15.13 13.63 32.8
125 x 125 x 100 139,7 x 139,7 x 114,3 419,1 384,3 346,1 14,8
139,7mm x 139,7mm x 133,0mm 5.500 x 5.500 x 5.250 16.50 16.13 14.00 35.5
125 x 125 x 125 139,7 x 139,7 x 133,0 419,1 409,7 355,6 16.1
139,7mm x 139,7mm x 139,7mm 5.500 x 5.500 x 5.500 16.50 16.13 14.00 36.8
125 x 125 x 125 139,7 x 139,7 x 139,7 419,1 409,7 355,6 16,7
5x5x3 5.563 x 5.563 x 3.500 16.50 14.25 13.25 28.4
125 x 125 x 80 141,3 x 141,3 x 88,9 419,1 362,0 336,6 12,9
5x5x4 5.563 x 5.563 x 4.500 16.50 15.13 13.63 32.8
125 x 125 x 100 141,3 x 141,3 x 114,3 418,6 384,3 346,1 14,9
5 x 5 x 139,7mm 5.563 x 5.563 x 5.500 16.50 16.13 14.00 37.6
125 x 125 x 125 141,3 x 141,3 x 139,7 418,6 409,7 355,6 17,0
5x5x5 5.563 x 5.563 x 5.563 16.50 16.13 14.00 38.8
125 x 125 x 125 141,3 x 141,3 x 141,3 418,6 409,7 355,6 17,6
159,0mm x 159,0mm x 3 6.250 x 6.250 x 3.500 18.50 15.31 14.81 38.2
150 x 150 x 80 159,0 x 159,0 x 88,9 469,9 388,9 376,2 17,3
TABLE 17 (1 OF 4)
FIGURE 330 FABRICATED TEE WYES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 39 of 64

E1

H
E2

Nominal Pipe Size

H E1 E2 Weight
O.D. Inches Inches Inches Lbs.
ANSI Inches mm mm mm kg
Inches
DN mm
159,0mm x 159,0mm x 108,0mm 6.250 x 6.250 x 4.252 18.50 16.25 15.25 39.4
150 x 150 x 100 159,0 x 159,0 x 108,0 469,9 412,8 387,4 17,8
159,0mm x 159,0mm x 4 6.250 x 6.250 x 4.500 18.50 16.25 15.25 41.5
150 x 150 x 100 159,0 x 159,0 x 114,3 469,9 412,8 387,4 18,8
159,0mm x 159,0mm x 133,0mm 6.250 x 6.250 x 5.250 18.50 17.25 15.63 43.2
150 x 150 x 125 159,0 x 159,0 x 133,0 469,9 438,2 396,9 19,5
159,0mm x 159,0mm x 5 6.250 x 6.250 x 5.563 18.50 17.25 15.63 47.3
150 x 150 x 125 159,0 x 159,0 x 141,3 469,9 438,2 396,9 21,5
159,0mm x 159,0mm x 159,0mm 6.250 x 6.250 x 6.250 18.50 18.25 16.00 53.5
150 x 150 x 150 159,0 x 159,0 x 159,0 469,9 463,6 406,4 24,3
165,1mm x 165,1mm x 3 6.500 x 6.500 x 3.500 18.50 15.31 14.81 40.0
150 x 150 x 80 165,1 x 165,1 x 88,9 469,9 388,9 376,2 18,1
165,1mm x 165,1mm x 4 6.500 x 6.500 x 4.500 18.50 16.25 15.25 41.8
150 x 150 x 100 165,1 x 165,1 x 114,3 469,9 412,8 387,4 18,9
165,1mm x 165,1mm x 139,7mm 6.500 x 6.500 x 5.500 18.50 17.25 15.63 42.8
150 x 150 x 125 165,1 x 165,1 x 139,7 469,9 438,2 396,9 19,4
165,1mm x 165,1mm x 5 6.500 x 6.500 x 5.563 18.50 17.25 15.63 43.6
150 x 150 x 125 165,1 x 165,1 x 141,3 469,9 438,2 396,9 19,7
165,1mm x 165,1mm x 165,1mm 6.500 x 6.500 x 6.500 18.50 18.25 16.00 54.2
150 x 150 x 150 165,1 x 165,1 x 165,1 469,9 463,6 406,4 24,5
6x6x3 6.625 x 6.625 x 3.500 18.50 15.31 14.81 37.9
150 x 150 x 80 168,3 x 168,3 x 88,9 469.9 388,9 376,2 17,2
6x6x4 6.625 x 6.625 x 4.500 18.50 16.25 15.25 42.5
150 x 150 x 100 168,3 x 168,3 x 114,3 469.9 412,8 387,4 19,3
6 x 6 x 139,7mm 6.625 x 6.625 x 5.500 18.50 17.25 15.63 45.6
150 x 150 x 125 168,3 x 168,3 x 139,7 469.9 438,2 396,9 20,6
6x6x5 6.625 x 6.625 x 5.563 18.50 17.25 15.63 48.5
150 x 150 x 125 168,3 x 168,3 x 141,3 469.9 438,2 396,9 22,0
6 x 6 x 165,1mm 6.625 x 6.625 x 6.500 18.50 18.25 16.00 52.3
150 x 150 x 150 168,3 x 168,3 x 165,1 469.9 463,6 406,4 23,7
6x6x6 6.625 x 6.625 x 6.625 18.50 18.25 16.00 56.3
150 x 150 x 150 168,3 x 168,3 x 168,3 469.9 463,6 406,4 25,5
216,3mm x 216,3mm x 3 8.516 x 8.516 x 3.500 24.00 18.19 19.19 67.3
200 x 200 x 80 216,3 x 216,3 x 88,9 609,6 462,0 487,4 30,5
216,3mm x 216,3mm x 4 8.516 x 8.516 x 4.500 24.00 19.00 19.50 72.3
200 x 200 x 100 216,3 x 216,3 x 114,3 609,6 482,6 495,3 32,8
216,3mm x 216,3mm x 139,7mm 8.516 x 8.516 x 5.500 24.00 20.00 19.87 74.2
200 x 200 x 125 216,3 x 216,3 x 139,7 609,6 508,0 504,7 33,6
216,3mm x 216,3mm x 5 8.516 x 8.516 x 5.563 24.00 20.00 19.87 78.8
200 x 200 x 125 216,3 x 216,3 x 141,3 609,6 508,0 504,7 35,7
216,3mm x 216,3mm x 165,1mm 8.516 x 8.516 x 6.500 24.00 21.13 20.37 84.9
200 x 200 x 150 216,3 x 216,3 x 165,1 609,6 536,7 517,4 38,5
216,3mm x 216,3mm x 6 8.516 x 8.516 x 6.625 24.00 21.13 20.37 87.4
200 x 200 x 150 216,3 x 216,3 x 168,3 609,6 536,7 517,4 39,6
216,3mm x 216,3mm x 216,3mm 8.516 x 8.516 x 8.516 24.00 23.25 21.25 102.2
200 x 200 x 200 216,3 x 216,3 x 216,3 609,6 590,6 539,8 46,4
TABLE 17 (2 OF 4)
FIGURE 330 FABRICATED TEE WYES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 40 of 64

E1

H
E2

Nominal Pipe Size

H E1 E2 Weight
O.D. Inches Inches Inches Lbs.
ANSI Inches mm mm mm kg
Inches
DN mm
8x8x3 8.625 x 8.625 x 3.500 24.00 18.19 19.19 67.3
200 x 200 x 80 219,1 x 219,1 x 88,9 609,6 462,0 487,4 30,5
8x8x4 8.625 x 8.625 x 4.500 24.00 19.00 19.50 72.3
200 x 200 x 100 219,1 x 219,1 x 114,3 609,6 482,6 495,3 32,8
8 x 8 x 139,7mm 8.625 x 8.625 x 5.500 24.00 20.00 19.87 75.2
200 x 200 x 125 219,1 x 219,1 x 139,7 609,6 508,0 504,7 34,1
8x8x5 8.625 x 8.625 x 5.563 24.00 20.00 19.87 78.8
200 x 200 x 125 219,1 x 219,1 x 141,3 609,6 508,0 504,7 35,7
8 x 8 x 165,1mm 8.625 x 8.625 x 6.500 24.00 21.13 20.37 85.2
200 x 200 x 150 219,1 x 219,1 x 165,1 609,6 536,7 517,4 38,6
8x8x6 8.625 x 8.625 x 6.625 24.00 21.13 20.37 87.4
200 x 200 x 150 219,1 x 219,1 x 168,3 609,6 536,7 517,4 39,6
8 x 8 x 216,3mm 8.625 x 8.625 x 8.516 24.00 23.25 21.25 106.7
200 x 200 x 200 219,1 x 219,1 x 216,3 609,6 590,6 539,8 48,4
8x8x8 8.625 x 8.625 x 8.625 24.00 23.25 21.25 109.0
200 x 200 x 200 219,1 x 219,1 x 219,1 609,6 590,6 539,8 49,4
267,4mm x 267,4mm x 3 10.528 x 10.528 x 3.500 27.00 19.88 21.38 106.7
250 x 250 x 80 267,4 x 267,4 x 88,9 685,8 505,0 543,1 48,4
267,4mm x 267,4mm x 4 10.528 x 10.528 x 4.500 27.00 20.75 21.75 111.8
250 x 250 x 100 267,4 x 267,4 x 114,3 685,8 527,1 552,5 50,7
267,4mm x 267,4mm x 139,7mm 10.528 x 10.528 x 5.500 27.00 21.88 22.25 112.7
250 x 250 x 125 267,4 x 267,4 x 139,7 685,8 555,8 565,2 51,1
267,4mm x 267,4mm x 5 10.528 x 10.528 x 5.563 27.00 21.88 22.25 113.6
250 x 250 x 125 267,4 x 267,4 x 141,3 685,8 555,8 565,2 51,5
267,4mm x 267,4mm x 165,1mm 10.528 x 10.528 x 6.500 27.00 22.88 22.63 147.3
250 x 250 x 150 267,4 x 267,4 x 165,1 685,8 581,2 574,7 66,8
267,4mm x 267,4mm x 6 10.528 x 10.528 x 6.625 27.00 22.88 22.63 151.1
250 x 250 x 150 267,4 x 267,4 x 168,3 685,8 581,2 574,7 68,5
267,4mm x 267,4mm x 216,3mm 10.528 x 10.528 x 8.516 27.00 27.25 25.75 167.8
250 x 250 x 200 267,4 x 267,4 x 216,3 685,8 692,2 654,1 76,1
267,4mm x 267,4mm x 8 10.528 x 10.528 x 8.625 27.00 27.25 25.75 175.1
250 x 250 x 200 267,4 x 267,4 x 219,1 685,8 692,2 654,1 79,4
267,4mm x 267,4mm x 267,4mm 10.528 x 10.528 x 10.750 27.00 27.25 24.38 184.4
250 x 250 x 250 267,4 x 267,4 x 273,0 685,8 692,2 619,1 83,6
10 x 10 x 3 10.750 x 10.750 x 3.500 27.00 19.88 21.38 101.7
250 x 250 x 80 273,0 x 273,0 x 88,9 685,8 505,0 543,1 46,1
10 x 10 x 4 10.750 x 10.750 x 4.500 27.00 20.75 21.75 106.9
250 x 250 x 100 273,0 x 273,0 x 114,3 685,8 527,1 552,5 48,5
10 x 10 x 139,7mm 10.750 x 10.750 x 5.500 27.00 21.88 22.25 108.7
250 x 250 x 125 273,0 x 273,0 x 139,7 685,8 555,8 565,2 49,3
10 x 10 x 5 10.750 x 10.750 x 5.563 27.00 21.88 22.25 113.8
250 x 250 x 125 273,0 x 273,0 x 141,3 685,8 555,8 565,2 51,6
10 x 10 x 165,1mm 10.750 x 10.750 x 6.500 27.00 22.88 22.63 118.7
250 x 250 x 150 273,0 x 273,0 x 165,1 685,8 581,2 574,7 53,8
10 x 10 x 6 10.750 x 10.750 x 6.625 27.00 22.88 22.63 122.1
250 x 250 x 150 273,0 x 273,0 x 168,3 685,8 581,2 574,7 55,4
TABLE 17 (3 OF 4)
FIGURE 330 FABRICATED TEE WYES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 41 of 64

E1

H
E2

Nominal Pipe Size

H E1 E2 Weight
O.D. Inches Inches Inches Lbs.
ANSI Inches mm mm mm kg
Inches
DN mm
10 x 10 x 216,3mm 10.750 x 10.750 x 8.516 27.00 27.25 25.75 147.6
250 x 250 x 200 273,0 x 273,0 x 216,3 685,8 692,2 654,1 67,0
10 x 10 x 8 10.750 x 10.750 x 8.626 27.00 27.25 25.75 151.1
250 x 250 x 200 273,0 x 273,0 x 219,1 685,8 692,2 654,1 68,5
10 x 10 x 267,4mm 10.750 x 10.750 x 10.528 27.00 27.25 24.38 171.8
250 x 250 x 250 273,0 x 273,0 x 267,4 685,8 692,2 619,1 77,9
10 x 10 x 10 10.750 x 10.750 x 10.750 27.00 27.25 24.38 175.1
250 x 250 x 250 273,0 x 273,0 x 273,0 685,8 692,2 619,1 79,4
318,5mm x 318,5mm x 3 12.539 x 12.539 x 3.500 30.00 22.75 20.75 132.2
300 x 300 x 80 318,5 x 318,5 x 88,9 762,0 527,1 527,1 60,0
318,5mm x 318,5mm x 4 12.539 x 12.539 x 4.500 30.00 21.50 23.00 134.6
300 x 300 x 100 318,5 x 318,5 x 114,3 762,0 546,1 584,2 61,1
318,5mm x 318,5mm x 165,1mm 12.539 x 12.539 x 6.500 30.00 23.75 24.00 150.7
300 x 300 x 150 318,5 x 318,5 x 165,1 762,0 603,3 609,6 68,4
318,5mm x 318,5mm x 6 12.539 x 12.539 x 6.625 30.00 23.75 24.00 152.7
300 x 300 x 150 318,5 x 318,5 x 168,3 762,0 603,3 609,6 69,3
318,5mm x 318,5mm x 216,3mm 12.539 x 12.539 x 8.516 30.00 26.00 25.00 171.6
300 x 300 x 200 318,5 x 318,5 x 216,3 762,0 660,4 635,0 77,8
318,5mm x 318,5mm x 8 12.539 x 12.539 x 8.625 30.00 26.00 25.00 174.1
300 x 300 x 200 318,5 x 318,5 x 219,1 762,0 660,4 635,0 78,9
318,5mm x 318,5mm x 267,4mm 12.539 x 12.539 x 10.528 30.00 28.00 25.75 234.5
300 x 300 x 250 318,5 x 318,5 x 267,4 762,0 771,2 654,1 106,4
318,5mm x 318,5mm x 10 12.539 x 12.539 x 10.750 30.00 28.00 25.75 238.7
300 x 300 x 250 318,5 x 318,5 x 273,0 762,0 771,2 654,1 108,3
318,5mm x 318,5mm x 318,5mm 12.539 x 12.539 x 12.539 30.00 31.00 27.50 232.1
300 x 300 x 300 318,5 x 318,5 x 318,5 762,0 787,4 698,5 105,3
12 x 12 x 3 12.750 x 12.750 x 3.500 30.00 22.75 20.75 134.5
300 x 300 x 80 323,9 x 323,9 x 88,9 762,0 527,1 527,1 61,0
12 x 12 x 4 12.750 x 12.750 x 4.500 30.00 21.50 23.00 139.4
300 x 300 x 100 323,9 x 323,9 x 114,3 762,0 546,1 584,2 63,2
12 x 12 x 165,1mm 12.750 x 12.750 x 6.500 30.00 23.75 24.00 145.7
300 x 300 x 150 323,9 x 323,9 x 165,1 762,0 603,3 609,6 66,1
12 x 12 x 6 12.750 x 12.750 x 6.625 30.00 23.75 24.00 154.5
300 x 300 x 150 323,9 x 323,9 x 168,3 762,0 603,3 609,6 70,0
12 x 12 x 216,3mm 12.750 x 12.750 x 8.516 30.00 26.00 25.00 166.7
300 x 300 x 200 323,9 x 323,9 x 216,3 762,0 660,4 635,0 75,6
12 x 12 x 8 12.750 x 12.750 x 8.625 30.00 26.00 25.00 175.8
300 x 300 x 200 323,9 x 323,9 x 219,1 762,0 660,4 635,0 79,7
12 x 12 x 267,4mm 12.750 x 12.750 x 10.528 30.00 28.00 25.75 184.1
300 x 300 x 250 323,9 x 323,9 x 267,4 762,0 711,2 654,1 83,5
12 x 12 x 10 12.750 x 12.750 x 10.750 30.00 28.00 25.75 205.4
300 x 300 x 250 323,9 x 323,9 x 273,0 762,0 711,2 654,1 93,2
12 x 12 x 318,5mm 12.750 x 12.750 x 12.539 30.00 31.00 27.50 228.7
300 x 300 x 300 323,9 x 323,9 x 318,5 762,0 787,4 698,5 103,7
12 x 12 x 12 12.750 x 12.750 x 12.750 30.00 31.00 27.50 240.1
300 x 300 x 300 323,9 x 323,9 x 323,9 762,0 787,4 698,5 108,9
TABLE 17 (4 OF 4)
FIGURE 330 FABRICATED TEE WYES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 42 of 64

E1
E2

Nominal Pipe Size

H E1 E2 Weight
O.D. Inches Inches Inches Lbs.
ANSI Inches mm mm mm kg
Inches
DN mm
108,0mm x 3 x 3 4.252 x 3.500 x 3.500 9.01 10.75 7.25 13.5
100 x 80 x 80 108,0 x 88,9 x 88,9 228,9 273,1 184,2 6,1
108,0mm x 3 x 108,0mm 4.252 x 3.500 x 4.2522 9.01 10.75 7.25 14.0
100 x 80 x 100 108,0 x 88,9 x 108,0 228,9 273,1 184,2 6,4
4x3x3 4.500 x 3.500 x 3.500 9.00 10.75 7.25 13.7
100 x 80 x 80 114,3 x 88,9 x 88,9 228,6 273,1 143,0 6,2
4 x 3 x 108,0mm 4.500 x 3.500 x 4.252 14.25 13.63 11.87 13.9
100 x 80 x 100 114,3 x 88,9 x 108,0 362,0 346,2 301,5 6,3
4x3x4 4.500 x 3.500 x 4.500 14.25 13.63 11.87 24.5
100 x 80 x 100 114,3 x 88,9 x 114,3 362,0 346,2 301,5 11,1
133,0mm x 3 x 3 5.250 x 3.500 x 3.500 11.00 11.50 7.71 19.0
125 x 80 x 80 133,0 x 88,9 x 88,9 279,5 292,1 195,8 8,6
133,0mm x 3 x 133,0mm 5.250 x 3.500 x 5.250 16.50 16.13 13.95 19.7
125 x 80 x 125 133,0 x 88,9 x 88,9 419,1 409,7 354,3 8,9
133,0mm x 4 x 3 5.250 x 4.500 x 3.500 11.00 11.88 8.71 19.5
125 x 100 x 80 133,0 x 114,3 x 88,9 279,4 301,88 221,2 8,8
133,0mm x 108,0mm x 3 5.250 x 4.252 x 3.500 11.00 11.88 8.71 19.5
125 x 100 x 80 133,0 x 108,0 x 88,9 279,4 301,88 221,2 8,8
133,0mm x 4 x 4 5.250 x 4.500 x 4.500 11.00 12.75 9.00 23.1
125 x 100 x 100 133,0 x 114,3 x 114,3 279,4 323,9 228,6 10,5
133,0mm x 108,0mm x 108,0mm 5.250 x 4.252 x 4.252 11.00 12.75 9.00 23.0
125 x 100 x 100 133,0 x 108,0 x 108,0 279,4 323,9 228,6 10,4
133,0mm x 108,0mm x 4 5.250 x 4.252 x 4.500 11.00 12.75 9.00 23.3
125 x 100 x 100 133,0 x 108,0 x 114,3 279,4 323,9 228,6 10,6
133,0mm x 4 x 108,0mm 5.250 x 4.500 x 4.252 11.00 12.75 9.00 18.8
125 x 100 x 100 133,0 x 114,3 x 108,0 279,4 323,9 228,6 8,5
139,7mm x 3 x 3 5.500 x 3.500 x 3.500 11.00 11.50 7.71 19.0
125 x 80 x 80 139,7 x 88,9 x 88,9 279,4 292,1 195,8 8,6
139,7mm x 3 x 139,7mm 5.500 x 3.500 x 5.500 16.50 16.13 13.95 19.7
125 x 80 x 125 139,7 x 88,9 x 139,7 419,1 409,7 354,3 8,9
139,7mm x 4 x 3 5.500 x 4.500 x 3.500 11.00 11.88 8.71 19.5
125 x 100 x 80 139,7 x 114,3 x 88,9 279,4 301,88 221,2 8,8
139,7mm x 4 x 4 5.500 x 4.500 x 4.500 11.00 12.75 9.00 23.0
125 x 100 x 100 139,7 x 114,3 x 114,3 279,4 323,9 228,6 10,4
5x3x3 5.563 x 3.500 x 3.500 11.00 11.50 7.71 19.0
125 x 80 x 80 141,3 x 88,9 x 88,9 279,4 292,1 195,8 8,6
5 x 3 x 133,0mm 5.563 x 3.500 x 5.250 16.50 16.13 13.95 19.7
125 x 80 x 125 141,3 x 88,9 x 133,0 419,1 409,7 254,0 8,9
5 x 3 x 139,7mm 5.563 x 3.500 x 5.500 16.50 16.13 13.95 19.9
125 x 80 x 125 141,3 x 88,9 x 139,7 419,1 409,7 254,0 9,0
5x3x5 5.563 x 3.500 x 5.563 16.50 16.13 13.95 38.5
125 x 80 x 125 141,3 x 88,9 x 141,3 419,1 409,7 254,0 17,5
5x4x3 5.563 x 4.500 x 3.500 11.00 11.88 8.71 19.5
125 x 100 x 80 141,3 x 114,3 x 88,9 279,4 301,88 221,2 8,8
5x4x4 5.563 x 4.500 x 4.500 11.00 12.75 9.00 23.1
125 x 100 x 100 141,3 x 114,3 x 114,3 279,4 323,9 228,6 10,5
159,0mm x 4 x 159,0mm 6.250 x 4.500 x 6.250 18.50 18.25 13.75 54.1
150 x 100 x 150 159,0 x 114,3 x 159,0 469,9 463,6 349,3 24,5
TABLE 18 (1 OF 2)
FIGURE 331 FABRICATED REDUCING TEE WYES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 43 of 64

E1
E2

Nominal Pipe Size

H E1 E2 Weight
O.D. Inches Inches Inches Lbs.
ANSI Inches mm mm mm kg
Inches
DN mm
159,0mm x 108,0mm x 159,0mm 6.250 x 4.252 x 6.250 18.50 18.25 13.75 56.2
150 x 100 x 150 159,0 x 108,0 x 159,0 469,9 463,6 349,3 25,5
159,0mm x 133,0mm x 108,0mm 6.250 x 5.250 x 4.252 12.00 13.88 9.63 55.1
150 x 125 x 100 159,0 x 133,0 x 108,0 304,9 352,5 244,6 25,0
159,0mm x 5 x 3 6.250 x 5.563 x 3.500 12.00 13.00 9.25 45.6
150 x 125 x 80 159,0 x 141,3 x 88,9 304,9 330,2 235,0 20,7
159,0mm x 5 x 4 6.250 x 5.563 x 4.500 12.00 13.88 9.62 55.0
150 x 125 x 100 159,0 x 141,3 x 114,3 304,9 352,6 244,3 24,9
159,0mm x 5 x 108,0mm 6.250 x 5.563 x 4.252 12.00 13.88 9.62 54.0
150 x 125 x 100 159,0 x 141,3 x 108,0 304,9 352,6 244,3 24,5
165,1mm x 4 x 165,1mm 6.250 x 4.500 x 6.250 18.50 18.25 13.75 56.2
150 x 100 x 150 159,0 x 114,3 x 159,0 469,9 463,6 349,3 25,5
165,1mm x 139,7mm x 3 6.250 x 5.500 x 3.500 12.00 13.00 9.25 45.6
150 x 1250 x 80 159,0 x 139,7 x 88,9 304,9 330,2 235,0 20,7
165,1mm x 139,7mm x 4 6.250 x 5.500 x 4.500 12.00 13.88 9.63 54.0
150 x 125 x 100 159,0 x 139,7 x 114,3 304,9 352,5 244,6 24,5
165,1mm x 5 x 3 6.500 x 5.563 x 3.500 12.00 13.00 9.25 45.6
150 x 125 x 80 165,1 x 141,3 x 88,9 304,9 330,2 235,0 20,7
165,1mm x 5 x 4 6.500 x 5.563 x 4.500 12.00 13.88 9.62 54.0
150 x 125 x 100 165,1 x 141,3 x 114,3 304,9 352,6 244,3 24,5
6 x 4 x 165,1mm 6.625 x 4.500 x 6.500 18.50 18.25 13.75 56.2
150 x 100 x 150 168,3 x 114,3 x 165,1 469,9 463,6 349,3 25,5
6x4x6 6.625 x 4.500 x 6.625 18.50 18.25 13.75 56.2
150 x 100 x 150 168,3 x 114,3 x 168,3 469,9 463,6 349,3 25,5
6 x 139,7mm x 3 6.625 x 5.500 x 3.500 12.00 13.00 9.25 25.0
150 x 125 x 80 168,3 x 139,7 x 88,9 304,9 330,2 235,0 11,3
6x5x3 6.625 x 5.563 x 3.500 12.00 13.00 9.25 25.6
150 x 125 x 80 168,3 x 141,3 x 88,9 304,9 330,2 235,0 11,6
6x5x4 6.625 x 5.563 x 4.500 12.00 13.88 9.62 29.3
150 x 125 x 100 168,3 x 141,3 x 114,3 304,9 352,6 244,3 13,3
216,3mm x 6 x 4 8.516 x 6.625 x 4.500 13.00 14.75 10.25 42.1
200 x 150 x 100 216,3 x 168,3 x 114,3 330,2 374,7 260,3 19,0
216,3mm x 6 x 216,3mm 8.516 x 6.625 x 8.516 24.00 23.25 21.25 107.0
200 x 150 x 200 216,3 x 168,3 x 216,3 609,6 590,5 539,7 48,5
216,3mm x 165,1mm x 4 8.516 x 4.500 x 4.500 13.00 14.75 10.25 44.0
200 x 150 x 100 216,3 x 114,3 x 114,3 330,2 374,7 260,3 20,0
216,3mm x 165,1mm x 216,3mm 8.516 x 4.500 x 8.516 24.00 23.25 21.25 107.0
200 x 150 x 200 216,3 x 114,3 x 216,3 609,6 590,5 539,7 48,5
8x6x4 8.625 x 6.625 x 4.500 13.00 14.75 10.25 40.2
200 x 150 x 100 219,1 x 168,3 x 114,3 330,2 374,7 260,3 18,2
8x6x8 8.625 x 6.625 x 8.625 24.00 23.25 21.25 108.6
200 x 150 x 200 219,1 x 168,3 x 219,1 609,6 590,6 539,8 49,3
8 x 165,1mm x 4 8.625 x 4.500 x 4.500 13.00 14.75 10.25 44.0
200 x 150 x 100 219,1 x 114,3 x 114,3 330,2 374,7 260,3 20,0
8 x 165,1mm x 8 8.625 x 4.500 x 8.625 24.00 23.25 21.25 106.0
200 x 150 x 200 219,1 x 114,3 x 219,1 609,6 590,6 539,8 48,0

TABLE 18 (2 OF 2)
FIGURE 331 FABRICATED REDUCING TEE WYES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 44 of 64

Nominal Pipe Size

E to E Weight
O.D. Inches Lbs.
ANSI Inches mm kg
Inches
DN mm
1-1/2 x 1 1.900 x 1.315 2.50 0.6
40 x 25 48,3 x 33,7 63,5 0,3
2 x 3/4 2.375 x 1.050 2.50 1.0
50 x 20 60,3 x 26,7 63,5 0,5
2x1 2.375 x 1.315 2.50 0.8
50 x 25 60,3 x 33,4 63,5 0,4
2 x 1-1/4 2.375 x 1.660 2.50 0.8
50 x 32 60,3 x 42,4 63,5 0,4
2 x 1-1/2 2.375 x 1.900 2.50 0.8
50 x 40 60,3 x 48,3 63,5 0,4
2-1/2 x 1-1/4 2.874 x 1.660 2.50 1.0
65 x 32 73,0 x 42,4 63,5 0,5
2-1/2 x 1-1/2 2.874 x 1.900 2.50 1.3
65 x 40 73,0 x 48,3 63,5 0,6
2-1/2 x 2 2.874 x 2.375 2.50 1.4
65 x 50 73,0 x 60,3 63,5 0,6
76,1mm x 1-1/4 3.000 x 1.660 2.50 1.0
65 x 32 76,1 x 42,4 63,5 0,5
76,1mm x 1-1/2 3.000 x 1.900 2.50 1.3
65 x 40 76,1 x 48,3 63,5 0,6
76,1mm x 2 3.000 x 2.375 2.50 1.4
65 x 50 76,1 x 60,3 63,5 0,6
E to E 3x1 3.500 x 1.315 2.50 1.8
80 x 25 88,9 x 33,4 63,5 0,8
3 x 1-1/4 3.500 x 1.660 2.5 1.8
80 x 32 88,9 x 42,4 63,5 0,8
3 x 1-1/2 3.500 x 1.900 2.50 1.9
80 x 40 88,9 x 48,3 63.5 0,9
3x2 3.500 x 2.375 2.50 1.9
80 x 50 88,9 x 60,3 63.5 0,9
3 x 2-1/2 3.500 x 2.874 2.50 2.2
80 x 65 88,9 x 73,0 63.5 0,9
3 x 76,1mm 3.500 x 3.000 2.50 2.2
80 x 65 88,9 x 76,1 63.5 0,9
108,0mm x 1 4.252 x 1.315 3.00 2.6
100 x 25 108,0 x 33,4 76,2 1,2
108,0mm x 1-1/4 4.252 x 1.660 3.00 2.6
100 x 32 108,0 x 42,4 76,2 1,2
108,0mm x 1-1/2 4.252 x 1.900 3.00 2.6
100 x 40 108,0 x 48,3 76,2 1,2
108,0mm x 2 4.252 x 2.375 3.00 2.7
100 x 50 108,0 x 60,3 76,2 1,2
108,0mm x 2-1/2 4.252 x 2.874 3.00 2.7
100 x 65 108,0 x 73,0 76,2 1,2
108,0mm x 76,1mm 4.252 x 3.500 3.00 2.7
100 x 65 108,0 x 76,1 76,2 1,2
108,0mm x 3 4.252 x 3.500 3.00 2.8
100 x 80 108,0 x 88,9 76,2 1,3
4x1 4.500 x 1.315 3.00 2.9
100 x 25 114,3 x 33,4 76,2 1,3
4 x 1-1/4 4.500 x 1.660 3.00 2.9
100 x 32 114,3 x 42,4 76,2 1,3
4 x 1-1/2 4.500 x 1.900 3.00 2.9
100 x 40 114,3 x 48,3 76,2 1,3
TABLE 19 (1 OF 3)
FIGURE 372 FABRICATED CONCENTRIC REDUCER GROOVE X MALE THREAD
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 45 of 64

Nominal Pipe Size

E to E Weight
O.D. Inches Lbs.
ANSI Inches mm kg
Inches
DN mm
4x2 4.500 x 2.375 3.00 2.9
100 x 50 114,3 x 60,3 76,2 1,3
4 x 2-1/2 4.500 x 2.874 3.00 3.0
100 x 65 114,3 x 73,0 76,2 1,4
4 x 76,1mm 4.500 x 3.000 3.00 3.0
100 x 65 114,3 x 76,1 76,2 1,4
4x3 4.500 x 3.500 3.00 3.2
100 x 80 114,3 x 88,9 76,2 1,5
133,0mm x 76,1mm 5.250 x 3.000 3.50 4.3
125 x 65 133,0 x 76,1 88,9 1,9
133,0mm x 3 5.250 x 3.500 3.50 4.3
125 x 80 133,0 x 88,9 88,9 1,9
133,0mm x 4 5.250 x 4.500 3.50 4.4
125 x 100 133,0 x 114, 3 88,9 2,0
139,7mm x 76,1mm 5.500 x 3.000 3.50 4.4
125 x 65 139,7 x 76,1 88,9 2,0
139,7mm x 3 5.500 x 3.500 3.50 4.4
125 x 80 139,7 x 88,9 88,9 2,0
139,7mm x 4 5.500 x 4.500 3.50 4.5
125 x 100 139,7 x 114,3 88,9 2,0
5 x 76,1mm 5.563 x 3.000 3.50 4.3
125 x 65 141,3 x 76,1 88,9 1,9
5x3 5.563 x 3.500 3.50 4.4 E to E
125 x 80 141,3 x 88,9 88,9 2,0
5x4 5.563 x 4.500 3.50 4.5
125 x 100 141,3 x 114,3 88,9 2,0
159,0mm x 1 6.250 x 1.315 4.00 5.2
150 x 25 159,0 x 33,4 101,6 2,4
159,0mm x 2 6.250 x 2.375 4.00 5.6
150 x 50 159,0 x 60,3 101,6 2,5
159,0mm x 76,1mm 6.250 x 3.000 4.00 5.6
150 x 65 159,0 x 76,1 101,6 2,5
159,0mm x 3 6.250 x 3.500 4.00 5.8
150 x 80 159,0 x 88,9 101,6 2,6
159,0mm x 4 6.250 x 4.500 4.00 6.0
150 x 100 159,0 x 114,3 101,6 2,7
159,0mm x 5 6.250 x 5.563 4.00 6.2
150 x 125 159,0 x 141,3 101,6 2,8
165,1mm x 1 6.500 x 1.315 4.00 5.6
150 x 25 165,1 x 33,4 101,6 2,5
165,1mm x 2 6.500 x 2.375 4.00 5.8
150 x 50 165,1 x 60,3 101,6 2,6
165,1mm x 76,1mm 6.500 x 3.000 4.00 6.0
150 x 65 165,1 x 76,1 101,6 2,7
165,1mm x 3 6.500 x 3.500 4.00 6.0
150 x 80 165,1 x 88,9 101,6 2,7
165,1mm x 4 6.500 x 4.500 4.00 6.3
150 x 100 165,1 x 114,3 101,6 2,8
165,1mm x 5 6.500 x 5.563 4.00 6.5
150 x 125 165,1 x 141,3 101,6 2,9
6x1 6.625 x 1.315 4.00 5.2
150 x 25 168,3 x 33,4 101,6 2,4
6x2 6.625 x 2.375 4.00 6.0
150 x 50 168,3 x 60,3 101,6 2,7
TABLE 19 (2 OF 3)
FIGURE 372 FABRICATED CONCENTRIC REDUCER GROOVE X MALE THREAD
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 46 of 64

Nominal Pipe Size

E to E Weight
O.D. Inches Lbs.
ANSI Inches mm kg
Inches
DN
E to E mm
6 x 76,1mm 6.625 x 3.000 4.00 6.0
150 x 65 168,3 x 76,1 101,6 2,7
6x3 6.625 x 3.500 4.00 6.0
150 x 80 168,3 x 88,9 101,6 2,7
6x4 6.625 x 4.500 4.00 6.3
150 x 100 168,3 x 114,3 101,6 2,8
6x5 6.625 x 5.563 4.00 6.5
150 x 125 168,3 x 141,3 101,6 2,9
TABLE 19 (3 OF 3)
FIGURE 372 FABRICATED CONCENTRIC REDUCER GROOVE X MALE THREAD
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS

Nominal Pipe Size

E to E Weight
O.D. Inches Lbs.
ANSI Inches mm kg
Inches
DN mm
1 1.315 2.06 0.7
25 33,4 52,4 0.3
1-1/4 1.660 2.3 1.4
32 42,4 58,7 0.6
1-1/2 1.900 2.3 1.5
E to E 40 48,3 58,7 0.7
2 2.375 2.50 1.6
50 60,3 63,5 0,7
2-1/2 2.874 2.75 1.9
65 73,0 69,8 0,9
76,1mm 3.000 2.50 2.0
65 76,1 63,5 0,9
3 3.500 2.75 2.5
80 88,9 69,9 1,1
108,0mm 4.252 3.25 4.2
100 108,0 82,5 1.9
4 4.500 3.25 4.5
100 114,3 82,5 2,0
TABLE 20
FIGURE 380 FABRICATED ADAPTER NIPPLE GROOVE X FEMALE THREAD
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 47 of 64

Figure 227 Figure 327

Nominal Pipe Size Cast Cross Fabricated Cross

ANSI O.D. C to E Weight C to E Weight

Inches Inches Inches Lbs. Inches Lbs.
DN mm mm kg mm kg

1-1/4 1.660 2.75 2.2 2.75 2.2

32 42,4 69,9 1,0 69,9 1,0
1-1/2 1.900 2.75 2.5 2.75 2.5
40 48,3 69,9 1,1 69,9 1,1
2 2.375 3.25 3.7 3.25 3.7
50 60,3 82,6 1,7 82,6 1,7
2-1/2 2.874 3.75 5.8 3.75 5.8
65 73,0 95,3 2,6 95,3 2,6
76,1mm 3.000 3.75 6.0 3.75 6.0
65 76,1 95,3 2,7 95,3 2,7
3 3.500 4.252 8.6 4.25 8.6
80 88,9 108,0 3,9 108,0 3,9
108,0mm 4.252 5.00
- - C to E
100 108,0 127,0
4 4.500 5.00 20.7 5.00 20.7
100 114,3 127,0 9,4 127,0 9,4
133,0mm 5.250 5.50 18.2
- -
125 133,0 139,7 8,3
139,7mm 5.500 5.50 18.4 C to E
- -
125 139,7 139,7 8,3 FIGURE 227
CAST CROSS
5 5.563 5.50 18.5 5.50 18.5
125 141,3 139,7 8,4 139,7 8,4
159,0mm 6.250 6.50
- -
150 159,0 165,1
165,1mm 6.500 6.50 18.5 6.50 18.5 C to E
150 165,1 165,1 8,4 165,1 8,4
6 6.625 6.50 27.3 6.50 27.3
150 168,3 165,1 12,4 165,1 12,4
216,3mm 8.516 7.75 47.6
- -
200 216,3 196,9 21,6 C to E
8 8.625 7.75 48.0 7.75 48.0 FIGURE 327
200 219,1 196,9 21,7 196,9 21,7 FABRICATED CROSS
267,4mm 10.528 9.00 74.1
- -
250 267,4 228,6 33,6
10 10.750 9.00 75.0 9.00 75.0
250 273,0 228,6 34,0 228,6 34,0
318,5mm 12.539 10.00 94.8
- -
300 318,5 254,0 43.0
12 12.750 10.00 95.8 10.00 95.8
300 323,9 254,0 43,4 254,0 43,4
14 14.000 11.00 136.8
- -
350 355,6 279,4 62,0
16 16.000 - - 12.00 167.3
400 406,4 304,8 75,9
18 18.000 15.50 259.5
450 457,2 - 393,7 117,7
20 20.000 - - 17.25 321.7
500 508,0 438,2 145,9
24 24.000 20.00 442.7
- -
600 609,6 508,0 200,8
TABLE 21
FIGURES 227 AND 327
CAST AND FABRICATED CROSSES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 48 of 64

Nominal Pipe Size

C to E Weight
O.D. Inches Lbs.
ANSI Inches mm kg
Inches
DN mm
2x2x1 2.375 x 2.375 x 1.315 3.25 2.2
50 x 50 x 25 60,3 x 60,3 x 33,4 82,6 1,0
2 x 2 x 1-1/4 2.375 x 2.375 x 1.660 3.25 2.3
50 x 50 x 32 60,3 x 60,3 x 42,4 82,6 1,0
2 x 2 x 1-1/2 2.375 x 2.375 x 1.900 3.25 1.4
50 x 50 x 40 60,3 x 60,3 x 48,3 82,6 1,1
2-1/2 x 2-1/2 x 1 2.874 x 2.874 x 1.315 3.75 3.6
65 x 65 x 25 73,0 x 73,0 x 33,4 95,3 1,6
2-1/2 x 2-1/2 x 1-1/4 2.874 x 2.874 x 1.660 3.75 3.8
65 x 65 x 32 73,0 x 73,0 x 42,4 95,3 1,7
2-1/2 x 2-1/2 x 1-1/2 2.874 x 2.874 x 1.900 3.75 4.0
65 x 65 x 40 73,0 x 73,0 x 48,3 95,3 1,8
2-1/2 x 2-1/2 x 2 2.874 x 2.874 x 2.375 3.75 4.2
65 x 65 x 50 73,0 x 73,0 x 60,3 95,3 1,9
76,1mm x 76,1mm x 1 3.000 x 3.000 x 1.315 3.75 3.7
65 x 65 x 25 76,1 x 76,1 x 33,4 95,3 1,7
76,1mm x 76,1mm x 1-1/4 3.000 x 3.000 x 1.660 3.75 3.9
65 x 65 x 32 76,1 x 76,1 x 42,4 95,3 1,8
76,1mm x 76,1mm x 1-1/2 3.000 x 3.000 x 1.900 3.75 4.1
65 x 65 x 40 76,1 x 76,1 x 48,3 95,3 1,9
C to E
76,1mm x 76,1mm x 2 3.000 x 3.000 x 2.375 3.75 4.4
65 x 65 x 50 76,1 x 76,1 x 60,3 95,3 2,0
3x3x1 3.500 x 3.500 x 1.315 4.25 5.7
80 x 80 x 25 88,9 x 88,9 x 33,4 108,0 2,6
3 x 3 x 1-1/2 3.500 x 3.500 x 1.900 4.25 5.8
C to E 80 x 80 x 40 88,9 x 88,9 x 48,3 108,0 2,6
NOTE: Figure 323 can be 3x3x2 3.500 x 3.500 x 2.375 4.25 5.9
supplied with either ISO 80 x 80 x 50 88,9 x 88,9 x 60,3 108,0 2,7
7-1 or NPT threads per 3 x 3 x 2-1/2 3.500 x 3.500 x 2.874 4.25 6.3
ASME B1.20.1 80 x 80 x 65 88,9 x 88,9 x 73,0 108,0 2,9
3 x 3 x 76,1mm 3.500 x 3.500 x 3.000 4.25 6.4
80 x 80 x 65 88,9 x 88,9 x 76,1 108,0 2,9
108,0mm x 108,0mm x 1 4.252 x 4.252 x 1.315 5.00 6,8
100 x 100 x 25 108,0 x 108,0 x 33,4 127,0 3,1
108,0mm x 108,0mm x 1-1/4 4.252 x 4.252 x 1.660 5.00 7.5
100 x 100 x 32 108,0 x 108,0 x 42,4 127,0 3,4
108,0mm x 108,0mm x 1-1/2 4.252 x 4.252 x 1.900 5.00 8.2
100 x 100 x 40 108,0 x 108,0 x 48,3 127,0 3,7
108,0mm x 108,0mm x 2 4.252 x 4.252 x 2.375 5.00 9.5
100 x 100 x 50 108,0 x 108,0 x 60,3 127,0 4,3
108,0mm x 108,0mm x 2-1/2 4.252 x 4.252 x 2.874 5.00 9.7
100 x 100 x 65 108,0 x 108,0 x 73,0 127,0 4,4
108,0mm x 108,0mm x 76,1mm 4.252 x 4.252 x 3.000 5.00 9.8
100 x 100 x 65 108,0 x 108,0 x 76,1 127,0 4,4
108,0mm x 108,0mm x 3 4.252 x 4.252 x 3.500 5.00 9.9
100 x 100 x 80 108,0 x 108,0 x 88,9 127,0 4,5
4x4x1 4.500 x 4.500 x 1.315 5.00 6.9
100 x 100 x 25 114,3 x 114,3 x 33,4 127,0 3,1
4 x 4 x 1-1/4 4.500 x 4.500 x 1.660 5.00 7.6
100 x 100 x 32 114,3 x 114,3 x 42,4 127,0 3,4
4 x 4 x 1-1/2 4.500 x 4.500 x 1.900 5.00 8.3
100 x 100 x 40 114,3 x 114,3 x 48,3 127,0 3,8
4x4x2 4.500 x 4.500 x 2.375 5.00 9.6
100 x 100 x 50 114,3 x 114,3 x 60,3 127,0 4,4
TABLE 22 (1 OF 5)
FIGURE 323 FABRICATED GROOVE X GROOVE X MALE THREAD REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 49 of 64

Nominal Pipe Size

C to E Weight
O.D. Inches Lbs.
ANSI Inches mm kg
Inches
DN mm
4 x 4 x 2-1/2 4.500 x 4.500 x 2.874 5.00 10.0
100 x 100 x 65 114,3 x 114,3 x 73,0 127,0 4,5
4 x 4 x 76,1mm 4.500 x 4.500 x 3.000 5.00 10.2
100 x 100 x 65 114,3 x 114,3 x 76,1 127,0 4,6
4x4x3 4.500 x 4.500 x 3.500 5.00 10.3
100 x 100 x 80 114,3 x 114,3 x 88,9 127,0 4,7
133,0mm x 133,0mm x 2 5.250 x 5.250 x 2.375 5.50 13.8
125 x 125 x 50 133,0 x 133,0 x 60,3 139,7 6,3
133,0mm x 133,0mm x 2-1/2 5.250 x 5.250 x 2.874 5.50 14.1
125 x 125 x 65 133,0 x 133,0 x 73,0 139,7 6,4
133,0mm x 133,0mm x 76,1mm 5.250 x 5.250 x 3.000 5.50 14.2
125 x 125 x 65 133,0 x 133,0 x 76,1 139,7 6,4
133,0mm x 133,0mm x 3 5.250 x 5.250 x 3.500 5.50 14.4
125 x 125 x 80 133,0 x 133,0 x 88,9 139,7 6,5
133,0mm x 133,0mm x 4 5.250 x 5.250 x 4.500 5.50 14.9
125 x 125 x 100 133,0 x 133,0 x 114,3 139,7 6,8
139,7mm x 139,7mm x 2 5.500 x 5.500 x 2.375 5.50 13.9
125 x 125 x 50 139,7 x 139,7 x 60,3 139,7 6,3
139,7mm x 139,7mm x 2-1/2 5.500 x 5.500 x 2.874 5.50 14.2
125 x 125 x 65 139,7 x 139,7 x 73,0 139,7 6,4
C to E
139,7mm x 139,7mm x 76,1mm 5.500 x 5.500 x 3.000 5.50 14.3
125 x 125 x 65 139,7 x 139,7 x 76,1 139,7 6,5
139,7mm x 139,7mm x 3 5.500 x 5.500 x 3.500 5.50 14.5
125 x 125 x 80 139,7 x 139,7 x 88,9 139,7 6,6
139,7mm x 139,7mm x 4 5.500 x 5.500 x 4.500 5.50 15.0
125 x 125 x 100 139,7 x 139,7 x 114,3 139,7 6,8 C to E
5x5x2 5.563 x 5.563 x 2.375 5.50 14.0 NOTE: Figure 323 can be
125 x 125 x 50 141,3 x 141,3 x 60,3 139,7 6,4 supplied with either ISO
5 x 5 x 76,1mm 5.563 x 5.563 x 3.000 5.50 14.4 7-1 or NPT threads per
125 x 125 x 65 141,3 x 141,3 x 76,1 139,7 6,5 ASME B1.20.1
5 x 5 x 2-1/2 5.563 x 5.563 x 2.874 5.50 14.3
125 x 125 x 65 141,3 x 141,3 x 73,0 139,7 6,5
5x5x3 5.563 x 5.563 x 3.500 5.50 14.6
125 x 125 x 80 141,3 x 141,3 x 88,9 139,7 6,6
5x5x4 5.563 x 5.563 x 4.500 5.50 15.1
125 x 125 x 100 141,3 x 141,3 x 114,3 139,7 6,8
159,0mm x 159,0mm x 2 6.250 x 6.250 x 2.375 6.50 20.9
150 x 150 x 50 159,0 x 159,0 x 60,3 165,1 9,5
159,0mm x 159,0mm x 76,1mm 6.250 x 6.250 x 3.000 6.50 21.3
150 x 150 x 65 159,0 x 159,0 x 76,1 165,1 9,7
159,0mm x 159,0mm x 2-1/2 6.250 x 6.250 x 2.874 6.50 21.2
150 x 150 x 65 159,0 x 159,0 x 73,0 165,1 9,6
159,0mm x 159,0mm x 3 6.250 x 6.250 x 3.500 6.50 21.6
150 x 150 x 80 159,0 x 159,0 x 88,9 165,1 9,8
159,0mm x 159,0mm x 4 6.250 x 6.250 x 4.500 6.50 22.1
150 x 150 x 100 159,0 x 159,0 x 114,3 165,1 10,0
159,0mm x 159,0mm x 139,7mm 6.250 x 6.250 x 5.500 6.50 22.4
150 x 150 x 125 159,0 x 159,0 x 139,7 165,1 10,2
159,0mm x 159,0mm x 5 6.250 x 6.250 x 5.563 6.50 22.7
150 x 150 x 125 159,0 x 159,0 x 141,3 165,1 10,3
165,1mm x 165,1mm x 2 6.500 x 6.500 x 2.375 6.50 21.1
150 x 150 x 50 165,1 x 165,1 x 60,3 165,1 9,6
165,1mm x 165,1mm x 76,1mm 6.500 x 6.500 x 3.000 6.50 21.5
150 x 150 x 65 165,1 x 165,1 x 76,1 165,1 9,8
TABLE 22 (2 OF 5)
FIGURE 323 FABRICATED GROOVE X GROOVE X MALE THREAD REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 50 of 64

Nominal Pipe Size

C to E Weight
O.D. Inches Lbs.
ANSI Inches mm kg
Inches
DN mm
165,1mm x 165,1mm x 2-1/2 6.500 x 6.500 x 2.874 6.50 21.4
150 x 150 x 65 165,1 x 165,1 x 73,0 165,1 9,7
165,1mm x 165,1mm x 3 6.500 x 6.500 x 3.500 6.50 21.8
150 x 150 x 80 165,1 x 165,1 x 88,9 165,1 9,9
165,1mm x 165,1mm x 4 6.500 x 6.500 x 4.500 6.50 22.3
150 x 150 x 100 165,1 x 165,1 x 114,3 165,1 10,1
165,1mm x 165,1mm x 139,7mm 6.500 x 6.500 x 5.500 6.50 22.6
150 x 150 x 125 165,1 x 165,1 x 139,7 165,1 10,3
165,1mm x 165,1mm x 5 6.500 x 6.500 x 5.563 6.50 22.9
150 x 150 x 125 165,1 x 165,1 x 141,3 165,1 10,4
6x6x2 6.625 x 6.625 x 2.375 6.50 21.3
150 x 150 x 50 168,3 x 168,3 x 60,3 165,1 9,7
6 x 6 x 2-1/2 6.625 x 6.625 x 2.874 6.50 21.7
150 x 150 x 65 168,3 x 168,3 x 73,0 165,1 9,8
6x6x3 6.625 x 6.625 x 3.500 6.50 22.0
150 x 150 x 80 168,3 x 168,3 x 88,9 165,1 10,0
6x6x4 6.625 x 6.625 x 4.500 6.50 22.5
150 x 150 x 100 168,3 x 168,3 x 114,3 165,1 10.2
6 x 6 x 139,7mm 6.625 x 6.625 x 5.500 6.50 22.8
150 x 150 x 125 168,3 x 168,3 x 139,7 165,1 10,3
C to E
6x6x5 6.625 x 6.625 x 5.563 6.50 23.1
150 x 150 x 125 168,3 x 168,3 x 141,3 165,1 10,5
216,3mm x 216,3mm x 2 8.516 x 8.516 x 2.375 7.75 32.5
200 x 200 x 50 216,3 x 216,3 x 60,3 196,9 14,7
216,3mm x 216,3mm x 76,1mm 8.516 x 8.516 x 3.000 7.75 32.7
C to E 200 x 200 x 65 216,3 x 216,3 x 76,1 196,9 14,8
NOTE: Figure 323 can be 216,3mm x 216,3mm x 3 8.516 x 8.516 x 3.500 7.75 33.3
supplied with either ISO 200 x 200 x 80 216,3 x 216,3 x 88,9 196,9 15,1
7-1 or NPT threads per 216,3mm x 216,3mm x 4 8.516 x 8.516 x 4.500 7.75 34.3
ASME B1.20.1 200 x 200 x 100 216,3 x 216,3 x 114,3 196,9 15,5
216,3mm x 216,3mm x 139,7mm 8.516 x 8.516 x 5.500 7.75 34.4
200 x 200 x 125 216,3 x 216,3 x 139,7 196,9 15,6
216,3mm x 216,3mm x 165,1mm 8.516 x 8.516 x 6.500 7.75 35.2
200 x 200 x 150 216,3 x 216,3 x 165,1 196,9 15,9
216,3mm x 216,3mm x 5 8.516 x 8.516 x 5.563 7.75 34.5
200 x 200 x 125 216,3 x 216,3 x 141,3 196,9 15,6
216,3mm x 216,3mm x 6 8.516 x 8.516 x 6.625 7.75 35.4
200 x 200 x 150 216,3 x 216,3 x 168,3 196,9 16.0
8x8x2 8.625 x 8.625 x 2.375 7.75 32.7
200 x 200 x 50 219,1 x 219,1 x 60,3 196,9 14,8
8 x 8 x 76,1mm 8.625 x 8.625 x 3.000 7.75 32.9
200 x 200 x 65 219,1 x 219,1 x 60,3 196,9 14,9
8x8x3 8.625 x 8.625 x 3.500 7.75 33.5
200 x 200 x 80 219,1 x 219,1 x 88,9 196,9 15,2
8x8x4 8.625 x 8.625 x 4.500 7.75 34.5
200 x 200 x 100 219,1 x 219,1 x 114,1 196,9 15,6
8 x 8 x 139,7mm 8.625 x 8.625 x 5.500 7.75 34.6
200 x 200 x 125 219,1 x 219,1 x 139,7 196,9 15,7
8 x 8 x 165,1mm 8.625 x 8.625 x 6.500 7.75 35.4
200 x 200 x 150 219,1 x 219,1 x 165,1 196,9 16,0
8x8x5 8.625 x 8.625 x 5.563 7.75 34.7
200 x 200 x 125 219,1 x 219,1 x 141,3 196,9 15,7
8x8x6 8.625 x 8.625 x 6.625 7.75 35.6
200 x 200 x 150 219,1 x 219,1 x 168,3 196,9 16,1
TABLE 22 (3 OF 5)
FIGURE 323 FABRICATED GROOVE X GROOVE X MALE THREAD REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 51 of 64

Nominal Pipe Size

C to E Weight
O.D. Inches Lbs.
ANSI Inches mm kg
Inches
DN mm
267,4mm x 267,4mm x 2 10.528 x 10.528 x 2.375 9.00 52.0
250 x 250 x 50 267,4 x 267,4 x 60,3 228.6 23,6
267,4mm x 267,4mm x 76,1mm 10.528 x 10.528 x 3.000 9.00 52.2
250 x 250 x 65 267,4 x 267,4 x 76,1 228.6 23,7
267,4mm x 267,4mm x 3 10.528 x 10.528 x 3.500 9.00 52.8
250 x 250 x 80 267,4 x 267,4 x 88,9 228.6 23,9
267,4mm x 267,4mm x 4 10.528 x 10.528 x 4.500 9.00 53.4
250 x 250 x 100 267,4 x 267,4 x 114,3 228.6 24.2
267,4mm x 267,4mm x 139,7mm 10.528 x 10.528 x 5.500 9.00 53.6
250 x 250 x 125 267,4 x 267,4 x 139,7 228.6 24,3
267,4mm x 267,4mm x 165,1mm 10.528 x 10.528 x 6.500 9.00 53.8
250 x 250 x 150 267,4 x 267,4 x 165,1 228.6 24,4
267,4mm x 267,4mm x 5 10.528 x 10.528 x 5.563 9.00 54.0
250 x 250 x 125 267,4 x 267,4 x 141,3 228.6 24,5
267,4mm x 267,4mm x 6 10.528 x 10.528 x 6.625 9.00 54.7
250 x 250 x 150 267,4 x 267,4 x 168,3 228.6 24,8
267,4mm x 267,4mm x 8 10.528 x 10.528 x 8.625 9.00 55.1
250 x 250 x 200 267,4 x 267,4 x 219,1 228.6 25,0
10 x 10 x 2 10.750 x 10.750 x 2.375 9.00 52.2
250 x 250 x 50 273,0 x 273,0 x 60,3 228,6 23,7
C to E
10 x 10 x 76,1mm 10.750 x 10.750 x 3.000 9.00 52.4
250 x 250 x 65 273,0 x 273,0 x 76,1 228,6 23,8
10 x 10 x 3 10.750 x 10.750 x 3.500 9.00 53.0
250 x 250 x 80 273,0 x 273,0 x 88,9 228,6 24,0
10 x 10 x 4 10.750 x 10.750 x 4.500 9.00 53.6
250 x 250 x 100 273,0 x 273,0 x 114,3 228,6 24,3 C to E
10 x 10 x 139,7mm 10.750 x 10.750 x 5.500 9.00 53.8 NOTE: Figure 323 can be
250 x 250 x 125 273,0 x 273,0 x 139,7 228,6 24,4 supplied with either ISO
10 x 10 x 165,1mm 10.750 x 10.750 x 6.500 9.00 54.0 7-1 or NPT threads per
250 x 250 x 150 273,0 x 273,0 x 165,1 228,6 24,5 ASME B1.20.1
10 x 10 x 5 10.750 x 10.750 x 5.563 9.00 54.2
250 x 250 x 125 273,0 x 273,0 x 141,3 228,6 24,6
10 x 10 x 6 10.750 x 10.750 x 6.625 9.00 54.9
250 x 250 x 150 273,0 x 273,0 x 168,3 228,6 24,9
10 x 10 x 8 10.750 x 10.750 x 8.625 9.00 55.3
250 x 250 x 200 273,0 x 273,0 x 219,1 228,6 25,1
318,5mm x 318,5mm x 3 12.539 x 12.539 x 3.500 10.00 74.2
300 x 300 x 80 318,5 x 318,5 x 88,9 254,0 33,7
318,5mm x 318,5mm x 4 12.539 x 12.539 x 4.500 10.00 74.9
300 x 300 x 100 318,5 x 318,5 x 114,3 254,0 33,9
318,5mm x 318,5mm x 139,7mm 12.539 x 12.539 x 5.500 10.00 75.2
300 x 300 x 125 318,5 x 318,5 x 139,7 254,0 34,1
318,5mm x 318,5mm x 5 12.539 x 12.539 x 5.563 10.00 75.4
300 x 300 x 125 318,5 x 318,5 x 141,3 254,0 34,2
318,5mm x 318,5mm x 165,1mm 12.539 x 12.539 x 6.500 10.00 75.8
300 x 300 x 150 318,5 x 318,5 x 165,1 254,0 34,4
318,5mm x 318,5mm x 6 12.539 x 12.539 x 6.625 10.00 76.0
300 x 300 x 150 318,5 x 318,5 x 168,3 254,0 34,5
318,5mm x 318,5mm x 8 12.539 x 12.539 x 8.625 10.00 76.1
300 x 300 x 200 318,5 x 318,5 x 219,1 254,0 34,5
318,5mm x 318,5mm x 10 12.539 x 12.539 x 10.750 10.00 77.4
300 x 300 x 250 318,5 x 318,5 x 273,0 254,0 35,1
12 x 12 x 3 12.750 x 12.750 x 3.500 10.00 74.6
300 x 300 x 80 323,9 x 323,9 x 88,9 254,0 33,8
TABLE 22 (4 OF 5)
FIGURE 323 FABRICATED GROOVE X GROOVE X MALE THREAD REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 52 of 64

Nominal Pipe Size

C to E Weight
O.D. Inches Lbs.
ANSI Inches mm kg
Inches
DN mm
C to E
12 x 12 x 4 12.750 x 12.750 x 4.500 10.00 75.1
300 x 300 x 100 323,9 x 323,9 x 141,3 254,0 34,1
12 x 12 x 139,7mm 12.750 x 12.750 x 5.500 10.00 75.4
300 x 300 x 125 323,9 x 323,9 x 139,7 254,0 34,2
12 x 12 x 5 12.750 x 12.750 x 5.563 10.00 75.6
C to E 300 x 300 x 125 323,9 x 323,9 x 114,3 254,0 34,3
NOTE: Figure 323 can be 12 x 12 x 165,1mm 12.750 x 12.750 x 6.500 10.00 76.0
supplied with either ISO 300 x 300 x 150 323,9 x 323,9 x 139,7 254,0 34,5
7-1 or NPT threads per 12 x 12 x 6 12.750 x 12.750 x 6.625 10.00 76.2
ASME B1.20.1 300 x 300 x 150 323,9 x 323,9 x 219,1 254,0 34,6
12 x 12 x 8 12.750 x 12.750 x 8.625 10.00 76.3
300 x 300 x 200 323,9 x 323,9 x 219,1 254,0 34,6
12 x 12 x 10 12.750 x 12.750 x 10.750 10.00 77.6
300 x 300 x 250 323,9 x 323,9 x 273,0 254,0 35,2
TABLE 22 (5 OF 5)
FIGURE 323 FABRICATED GROOVE X GROOVE X MALE THREAD REDUCING TEES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 53 of 64

Nominal Pipe Size

C to LE C to SE Weight
ANSI O.D. Inches Inches Lbs.
Inches Inches mm mm kg
DN mm
1-1/4 1.660 2.75 2.50 1.4
32 42,4 69,9 63,5 0,6
1-1/2 1.900 2.75 2.75 1.7
40 48,3 69,9 69,9 0,8
2 2.375 3.25 2.75 2.5
50 60,3 82,6 69,9 1,1
2-1/2 2.874 3.75 3.00 4.4
65 73,0 95,3 76,2 2,0
76,1mm 3.000 3.75 3.00 4.4
65 76,1 95,3 76,2 2,0
3 3.500 4.25 3.25 6.4
80 88,9 108,0 82,6 2,9
108,0mm 4.252 5.00 3.75 10.3
100 108,0 127,0 95,3 4,7
4 4.500 5.00 3.75 10.5
100 114,3 127,0 95,3 4,8
133,0mm 5.250 5.50 4.00 14.8
125 133,0 139,7 101,6 6,7
139,7mm 5.500 5.50 4.00 15.0
125 139,7 139,7 101,6 6,8
5 5.563 5.50 4.00 15.2 C to LE
125 141,3 139,7 101,6 6,9
159,0mm 6.250 6.50 4.50 21.6
150 159,0 165,1 114,3 9,8 C to SE

165,1mm 6.500 6.50 4.50 22.9

150 165,1 165,1 114,3 10,4
6 6.625 6.50 4.50 22.9
150 168,3 165,1 114,3 10,4
216,3mm 8.516 7.75 6.00 41.5
200 216,3 196,9 152,4 18,8
8 8.625 7.75 6.00 41.9
200 219,1 196,9 152,4 19,0
267,4mm 10.528 9.00 6.50 65.8
250 267,4 228,6 165,71 29,8
10 10.750 9.00 6.50 66.2
250 273,0 228,6 165,71 30,0
318,5mm 12.539 10.00 7.00 87.2
300 318,5 254,0 177,8 39,5
12 12.750 10.00 7.00 87.7
300 323,9 254,0 177,8 39,8
14 14.000 11.00 7.50 105.3
350 355,6 279,4 190,5 47.8
16 16.000 12.00 8.00 129.1
400 406,4 304,8 203,2 58,6
18 18.000 15.50 8.50 184.4
450 457,2 393,7 215,9 83,6
20 20.000 17.25 9.00 225.8
500 508,0 438,2 238,6 102,4
24 24.000 20.00 10.00 308.5
600 609,6 508,0 254,0 139,9
TABLE 23
FIGURE 324 FABRICATED 90° TRUE Y
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 54 of 64

Figure 341 Figure 342

Nominal Pipe Size Fabricated Flange Adapter Fabricated Flange Adapter
ANSI Class 150 Lbs. ANSI Class 300 Lbs. E to E
Inches
ANSI O.D. Mating Weight Mating Weight mm
Inches Inches Flange Bolt Lbs. Flange Bolt Lbs.
DN mm Qty. kg Qty. kg
1-1/4 1.660 3.7 4.6 4.00
4 4
32 42,4 1,7 2,1 101,6
1-1/2 1.900 3.9 7.1 4.00
4 4
40 48,3 1,8 3,2 101,6
2 2.375 6.4 8.2 4.00
4 8
50 60,3 2,8 3,7 101,6
2-1/2 2.874 8.8 11.9 4.00
4 8
65 73,0 4,0 5,4 101,6
76,1mm 3.000 10.0 12.5 4.00
4 8
65 76,1 4,5 5,7 101,6
3 3.500 10.4 15.5 4.00
4 8
80 88,9 4,7 7,0 101,6
108,0mm 4.252 18.0 27.2 6.00
8 8
100 108,0 8,2 12,3 152,4
4 4.500 18.2 28.0 6.00
8 8
100 114,3 8,3 12,7 152,4
133,0mm 5.250 21.5 35 6.00
8 8
125 133,0 9,8 15,9 152,4
139,7mm 5.500 21.8 36 6.00
8 8
E to E 125 139,7 9,9 16,3 152,4
5 5.563 22.0 37.0 6.00
8 8
125 141,3 10,0 16,8 152,4
159,0mm 6.250 27.5 46 6.00
8 12
150 159,0 12.5 20,9 152,4
165,1mm 6.500 27.8 47 6.00
8 12
150 165,1 12,6 21,3 152,4
6 6.625 28.1 48.0 6.00
8 12
150 168,3 12,7 21,8 152,4
216,3mm 8.516 43.2 77 6.00
8 12
200 216,3 19,6 34,9 152,4
8 8.625 43.7 79.0 6.00
8 12
200 219,1 19,8 35,8 152,4
267,4mm 10.528 68.2 86 8.00
12 16
250 267,4 30,9 39.0 203,2
10 10.750 68.2 122.0 8.00
12 16
250 273,0 30,9 55,3 203,2
318,5mm 12.539 88.0 175.0 8.00
12 16
300 318,5 39.9 79,4 203,2
12 12.750 96.1 183.0 8.00
12 16
300 323,9 43,6 83,0 203,2
14 14.000 123.0 199.0 8.00
12 20
350 355,6 55,8 90,3 203,2
16 16.000 151.0 255.0 8.00
16 20
400 406,4 68,5 155,7 203,2
18 18.000 165.0 303.0 8.00
16 24
450 457,2 74,8 137,4 203,2
20 20.000 205.0 365.0 8.00
20 24
500 508,0 93,0 165,6 203,2
24 24.000 265.0 550.0 8.00
20 24
600 609,6 120,2 249,5 203,2
TABLE 24
FIGURES 341 AND 342 FABRICATED FLANGE ADAPTERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 55 of 64

Figure 343 Figure 344

Nominal Pipe Size Fabricated Flange Adapter Fabricated Flange Adapter
PN16 PN10 E to E
Inches
ANSI O.D. Mating Weight Mating Weight mm
Inches Inches Flange Bolt Lbs. Flange Bolt Lbs.
DN mm Qty. kg Qty. kg
2 2.375 6.4 3.74
4 - -
50 60,3 2,9 95,0
2-1/2 2.874 8.8 3.74
4 - -
65 73,0 4,0 95,0
76,1mm 3.000 10.0 3.74
4 - -
65 76,1 45,4 95,0
3 3.500 10.4 3.94
8 - -
80 88,9 4,7 100,0
108,0mm 4.252 18.0 4.02
8 - -
100 108,0 8,2 102,0
4 4.500 18.2 4.02
8 - -
100 114,3 8,3 102,0
133,0mm 5.250 21.5 4.13 E to E
8 - -
125 133,0 9,8 105,0
139,7mm 5.500 21.8 4.13
8 - -
125 139,7 9,9 105,0
5 5.563 22.0 4.13
8 - -
125 141,3 10,0 105,0
159,0mm 6.250 27.5 4.13
8 - -
150 159,0 12,5 105,0
165,1mm 6.500 27.8 4.13
8 - -
150 165,1 12,6 105,0
6 6.625 28.1 4.13
8 - -
150 168,3 12,7 105,0
216,3mm 8.516 43.2 42.6 4.40
12 8
200 216,3 19,6 19,3 112,0
8 8.625 43.7 43.1 4.40
12 8
200 219,1 19.8 19,5 112,0
267,4mm 10.528 68.2 67.1 5.43
12 12
250 267,4 30,9 30,4 138,0
10 10.750 68.5 67.4 5.43
12 12
250 273,0 31,1 30.6 138,0
318,5mm 12.539 94.5 93.1 5.43
12 12
300 318,5 29,3 42,2 138,0
12 12.750 96.1 94.0 5.43
12 12
300 323,9 43,6 42,6 138,0
TABLE 25
FIGURES 343 AND 344 FABRICATED FLANGE ADAPTERS
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 56 of 64

E to E E to E E to E

FIGURE 397 FIGURE 398 FIGURE 399

FABRICATED SWAGED NIPPLE FABRICATED SWAGED NIPPLE FABRICATED SWAGED NIPPLE
GROOVE X GROOVE GROOVE X MALE THREAD GROOVE X PLAIN
Figures 397 Figures 398 Figures 399
Nominal Pipe Size Fabricated Swaged Fabricated Swaged Fabricated Swaged
Nipple Nipple Nipple
O.D. E to E Weight E to E Weight E to E Weight
ANSI Inches Inches Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg
2x1 2.375 x 1.315 6.50 2.0 6.50 2.0 6.50 2.0
50 x 25 60,3 x 33,4 165,1 0,9 165,1 0,9 165,1 0,9
2 x 1-1/4 2.375 x 1.660 6.50 2.0 6.50 2.0 6.50 2.0
50 x 32 60,3 x 42,4 165,1 0,9 165,1 0,9 165,1 0,9
2 x 1-1/2 2.375 x 1.900 6.50 2.0 6.50 2.0 6.50 2.0
50 x 40 60,3 x 48,3 165,1 0,9 165,1 0,9 165,1 0,9
2-1/2 x 1 2.874 x 1.315 7.00 3.5 7.00 3.5 7.00 3.5
65 x 25 73,0 x 33,4 177,8 1,6 177,8 1,6 177,8 1,6
2-1/2 x 1-1/4 2.874 x 1.660 7.00 3.5 7.00 3.5 7.00 3.5
65 x 32 73,0 x 42,4 177,8 1,6 177,8 1,6 177,8 1,6
2-1/2 x 1-1/2 2.874 x 1.900 7.00 3.5 7.00 3.5 7.00 3.5
65 x 40 73,0 x 48,3 177,8 1,6 177,8 1,6 177,8 1,6
2-1/2 x 2 2.874 x 2.375 7.00 3.5 7.00 3.5 7.00 3.5
65 x 50 73,0 x 60,3 177,8 1,6 177,8 1,6 177,8 1,6
76,1mm x 1 3.000 x 1.315 7.00 3.6 7.00 3.6 7.00 2.2
65 x 25 76,1 x 33,4 177,8 1,6 177,8 1,6 177,8 0.9
76,1mm x 1-1/4 3.000 x 1.660 7.00 3.6 7.00 3.6 7.00 3.2
65 x 32 76,1 x 42,4 177,8 1,6 177,8 1,6 177,8 1,5
76,1mm x 1-1/2 3.000 x 1.900 7.00 3.7 7.00 3.7 7.00 3.7
65 x 40 76,1 x 48,3 177,8 1,7 177,8 1,7 177,8 1,7
76,1mm x 2 3.000 x 2.375 7.00 3.7 7.00 3.7 7.00 3.7
65 x 50 76,1 x 60,3 177,8 1,7 177,8 1,7 177,8 1,7
3x1 3.500 x 1.315 8.00 5.0 8.00 5.0 8.00 5.0
80 x 25 88,9 x 33,4 203,2 2,3 203,2 2,3 203,2 2,3
3 x 1-1/4 3.500 x 1.660 8.00 5.0 8.00 5.0 8.00 5.0
80 x 32 88,9 x 42,4 203,2 2,3 203,2 2,3 203,2 2,3
3 x 1-1/2 3.500 x 1.900 8.00 5.0 8.00 5.0 8.00 5.0
80 x 40 88,9 x 48,3 203,2 2,3 203,2 2,3 203,2 2,3
3x2 3.500 x 2.375 8.00 5.0 8.00 5.0 8.00 5.0
80 x 50 88,9 x 60,3 203,2 2,3 203,2 2,3 203,2 2,3
3 x 2-1/2 3.500 x 2.874 8.00 5.0 8.00 5.0 8.00 5.0
80 x 65 88,9 x 73,0 203,2 2,3 203,2 2,3 203,2 2,3
3 x 76,1mm 3.500 x 3.000 8.00 5.2 8.00 5.2 8.00 5.2
80 x 65 88,9 x 73,0 203,2 2,4 203,2 2,4 203,2 2,4
108,0mm x 1 4.252 x 1.315 9.00 5.2 9.00 5.2 9.00 5.2
100 x 25 108,0 x 33,4 228,6 2,4 228,6 2,4 228,6 2,4
108,0mm x 1-1/4 4.252 x 1.660 9.00 5.2 9.00 5.2 9.00 5.2
100 x 32 108,0 x 42,4 228,6 2,4 228,6 2,4 228,6 2,4
108,0mm x 1-1/2 4.252 x 1.900 9.00 5.6 9.00 5.6 9.00 5.6
100 x 40 108,0 x 48,3 228,6 2,5 228,6 2,5 228,6 2,5
108,0mm x 2 4.252 x 2.375 9.00 5.6 9.00 5.6 9.00 5.6
100 x 50 108,0 x 60,3 228,6 2,5 228,6 2,5 228,6 2,5
108,0mm x 2-1/2 4.252 x 2.874 9.00 6.7 9.00 6.7 9.00 6.7
100 x 65 108,0 x 73,0 228,6 3,0 228,6 3,0 228,6 3,0
108,0mm x 76,1mm 4.252 x 3.000 9.00 6.7 9.00 6.7 9.00 6.7
100 x 65 108,0 x 76,1 228,6 3,0 228,6 3,0 228,6 3,0
TABLE 26 (1 OF 4)
FIGURES 397, 398 AND 399 FABRICATED SWAGED NIPPLES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 57 of 64

E to E E to E E to E

FIGURE 397 FIGURE 398 FIGURE 399

FABRICATED SWAGED NIPPLE FABRICATED SWAGED NIPPLE FABRICATED SWAGED NIPPLE
GROOVE X GROOVE GROOVE X MALE THREAD GROOVE X PLAIN
Figures 397 Figures 398 Figures 399
Nominal Pipe Size Fabricated Swaged Fabricated Swaged Fabricated Swaged
Nipple Nipple Nipple
O.D. E to E Weight E to E Weight E to E Weight
ANSI Inches Inches Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg
108,0mm x 3 4.252 x 3.500 9.00 6.7 9.00 6.7 9.00 6.7
100 x 80 108,0 x 88,9 228,6 3,0 228,6 3,0 228,6 3,0
4x1 4.500 x 1.315 9.00 8.0 9.00 8.0 9.00 8.0
100 x 25 114,3 x 33,4 228,6 3,6 228,6 3,6 228,6 3,6
4 x 1-1/4 4.500 x 1.660 9.00 8.0 9.00 8.0 9.00 8.0
100 x 32 114,3 x 42,4 228,6 3,6 228,6 3,6 228,6 3,6
4 x 1-1/2 4.500 x 1.900 9.00 8.0 9.00 8.0 9.00 8.0
100 x 40 114,3 x 48,3 228,6 3,6 228,6 3,6 228,6 3,6
4x2 4.500 x 2.375 9.00 8.0 9.00 8.0 9.00 8.0
100 x 50 114,3 x 60,3 228,6 3,6 228,6 3,6 228,6 3,6
4 x 2-1/2 4.500 x 2.874 9.00 8.0 9.00 8.0 9.00 8.0
100 x 65 114,3 x 73,0 228,6 3,6 228,6 3,6 228,6 3,6
4 x 76,1mm 4.500 x 3.000 9.00 8.0 9.00 8.0 9.00 8.0
100 x 65 114,3 x 76,1 228,6 3,6 228,6 3,6 228,6 3,6
4x3 4.500 x 3.500 9.00 8.0 9.00 8.0 9.00 8.0
100 x 80 114,3 x 88,9 228,6 3,6 228,6 3,6 228,6 3,6
133,0mm x 1-1/2 5.250 x 1.900 11.00 8.4 11.00 8.4 - -
125 x 40 133,0 x 48,3 279,4 3,8 279,4 3,8
133,0mm x 2 5.250 x 2.375 11.00 8.4 11.00 8.4 11.00 8.4
125 x 50 133,0 x 60,3 279,4 3,8 279,4 3,8 279,4 3,8
133,0mm x 2-1/2 5.250 x 2.874 11.00 8.4 11.00 8.4 11.00 8.4
125 x 65 133,0 x 73,0 279,4 3,8 279,4 3,8 279,4 3,8
133,0mm x 76,1mm 5.250 x 3.000 11.00 8.4 11.00 8.4 11.00 8.4
125 x 65 133,0 x 76,1 279,4 3,8 279,4 3,8 279,4 3,8
133,0mm x 3 5.250 x 3.500 11.00 8.4 11.00 8.4 11.00 8.4
125 x 80 133,0 x 88,9 279,4 3,8 279,4 3,8 279,4 3,8
133,0mm x 108,0mm 5.250 x 4.252 11.00 9.1 11.00 9.1
- -
125 x 100 133,0 x 108,0 279,4 4,1 279,4 4,1
133,0mm x 4 5.250 x 4.500 11.00 9.1 11.00 9.1 11.00 9.1
125 x 100 133,0 x 114,3 279,4 4,1 279,4 4,1 279,4 4,1
139,7mm x 1-1/2 5.500 x 1.900 11.00 9.1 11.00 9.1 11.00 9.1
125 x 40 139,7 x 48,3 279,4 4,1 279,4 4,1 279,4 4,1
139,7mm x 2 5.500 x 2.375 11.00 9.1 11.00 9.1 11.00 9.1
125 x 50 139,7 x 60,3 279,4 4,1 279,4 4,1 279,4 4,1
139,7mm x 2-1/2 5.500 x 2.874 11.00 9.1 11.00 9.1 11.00 9.1
125 x 65 139,7 x 73,0 279,4 4,1 279,4 4,1 279,4 4,1
139,7mm x 76,1mm 5.500 x 3.000 11.00 9.1 11.00 9.1 11.00 9.1
125 x 65 139,7 x 76,1 279,4 4,1 279,4 4,1 279,4 4,1
139,7mm x 3 5.500 x 3.500 11.00 11.2 11.00 11.2 11.00 11.2
125 x 80 139,7 x 88,9 279,4 5,1 279,4 5,1 279,4 5,1
139,7mm x 108,0mm 5.500 x 4.252 11.00 11.2 11.00 11.2
- -
125 x 100 139,7 x 108,0 279,4 5,1 279,4 5,1
139,7mm x 4 5.500 x 4.500 11.00 11.2 11.00 11.2 11.00 11.2
125 x 100 139,7 x 114,3 279,4 5,1 279,4 5,1 279,4 5,1
5 x 1-1/2 5.563 x 1.900 11.00 11.2 11.00 11.2 11.00 11.2
125 x 40 141,3 x 48,3 279,4 5,1 279,4 5,1 279,4 5,1
TABLE 26 (2 OF 4)
FIGURES 397, 398 AND 399 FABRICATED SWAGED NIPPLES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 58 of 64

E to E E to E E to E

FIGURE 397 FIGURE 398 FIGURE 399

FABRICATED SWAGED NIPPLE FABRICATED SWAGED NIPPLE FABRICATED SWAGED NIPPLE
GROOVE X GROOVE GROOVE X MALE THREAD GROOVE X PLAIN
Figures 397 Figures 398 Figures 399
Nominal Pipe Size Fabricated Swaged Fabricated Swaged Fabricated Swaged
Nipple Nipple Nipple
O.D. E to E Weight E to E Weight E to E Weight
ANSI Inches Inches Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg
5x2 5.563 x 2.375 11.00 12.0 11.00 12.0 11.00 12.0
125 x 50 141,3 x 60,3 279,4 5,4 279,4 5,4 279,4 5,4
5 x 2-1/2 5.563 x 2.874 11.00 12.0 11.00 12.0 11.00 12.0
125 x 65 141,3 x 73,0 279,4 5,4 279,4 5,4 279,4 5,4
5 x 76,1mm 5.563 x 3.000 11.00 12.0 11.00 12.0 11.00 12.0
125 x 65 141,3 x 76,1 279,4 5,4 279,4 5,4 279,4 5,4
5x3 5.563 x 3.500 11.00 12.0 11.00 12.0 11.00 12.0
125 x 80 141,3 x 88,9 279,4 5,4 279,4 5,4 279,4 5,4
5 x 108,0mm 5.563 x 4.252 11.00 12.0 11.00 12.0
- -
125 x 100 141,3 x 108,0 279,4 5,4 279,4 5,4
5x4 5.563 x 4.500 11.00 12.0 11.00 12.0 11.00 12.0
125 x 100 141,3 x 114,3 279,4 5,4 279,4 5,4 279,4 5,4
159,0mm x 1 6.250 x 1.315 12.00 12.2 12.00 12.2 12.00 12.2
150 x 25 159,0 x 33,4 304,8 5,5 304,8 5,5 304,8 5,5
159,0mm x 1-1/4 6.250 x 1.660 12.00 12.2 12.00 12.2 12.00 12.2
150 x 32 159,0 x 42,4 304,8 5,5 304,8 5,5 304,8 5,5
159,0mm x 1-1/2 6.250 x 1.900 12.00 12.2 12.00 12.2 12.00 12.2
150 x 40 159,0 x 48,3 304,8 5,5 304,8 5,5 304,8 5,5
159,0mm x 2 6.250 x 2.375 12.00 12.4 12.00 12.4 12.00 12.4
150 x 50 159,0 x 60,3 304,8 5,6 304,8 5,6 304,8 5,6
159,0mm x 2-1/2 6.250 x 2.874 12.00 12.4 12.00 12.4 12.00 12.4
150 x 65 159,0 x 73,0 304,8 5,6 304,8 5,6 304,8 5,6
159,0mm x 76,1mm 6.250 x 3.000 12.00 12.4 12.00 12.4 12.00 12.4
150 x 65 159,0 x 76,1 304,8 5,6 304,8 5,6 304,8 5,6
159,0mm x 3 6.250 x 3.500 12.00 12.4 12.00 12.4 12.00 12.4
150 x 80 159,0 x 88,9 304,8 5,6 304,8 5,6 304,8 5,6
159,0mm x 108,0mm 6.250 x 4.252 12.00 12.9 12.00 12.9
- -
150 x 100 159,0 x 108,0 304,8 5,9 304,8 5,9
159,0mm x 4 6.250 x 4.500 12.00 12.9 12.00 12.9 12.00 12.9
150 x 100 159,0 x 114,3 304,8 5,9 304,8 5,9 304,8 5,9
159,0mm x 133,0mm 6.250 x 5.250 12.00 12.9 12.00 12.9
- -
150 x 125 159,0 x 133,0 304,8 5,9 304,8 5,9
159,0mm x 139,7mm 6.250 x 5.500 12.00
- - - -
150 x 125 159,0 x 139,7 304,8
159,0mm x 5 6.250 x 5.563 12.00 13.0 12.00 13.0 12.00 13.0
150 x 125 159,0 x 141,3 304,8 5,9 304,8 5,9 304,8 5,9
165,1mm x 1 6.500 x 1.315 12.00 15.8 12.00 15.8 12.00 15.8
150 x 25 165,1 x 33,4 304,8 7,2 304,8 7,2 304,8 7,2
165,1mm x 1-1/4 6.500 x 1.660 12.00 15.8 12.00 15.8 12.00 15.8
150 x 32 165,1 x 42,4 304,8 7,2 304,8 7,2 304,8 7,2
165,1mm x 1-1/2 6.500 x 1.900 12.00 15.8 12.00 15.8 12.00 15.8
150 x 40 165,1 x 48,3 304,8 7,2 304,8 7,2 304,8 7,2
165,1mm x 2 6.500 x 2.375 12.00 15.8 12.00 15.8 12.00 15.8
150 x 50 165,1 x 60,3 304,8 7,2 304,8 7,2 304,8 7,2
165,1mm x 2-1/2 6.500 x 2.874 12.00 16.4 12.00 16.4 12.00 16.4
150 x 65 165,1 x 73,0 304,8 7,4 304,8 7,4 304,8 7,4
TABLE 26 (3 OF 4)
FIGURES 397, 398 AND 399 FABRICATED SWAGED NIPPLES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 59 of 64

E to E E to E E to E

FIGURE 397 FIGURE 398 FIGURE 399

FABRICATED SWAGED NIPPLE FABRICATED SWAGED NIPPLE FABRICATED SWAGED NIPPLE
GROOVE X GROOVE GROOVE X MALE THREAD GROOVE X PLAIN
Figures 397 Figures 398 Figures 399
Nominal Pipe Size Fabricated Swaged Fabricated Swaged Fabricated Swaged
Nipple Nipple Nipple
O.D. E to E Weight E to E Weight E to E Weight
ANSI Inches Inches Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg
165,1mm x 76,1mm 6.500 x 3.000 12.00 16.4 12.00 16.4 12.00 16.4
150 x 65 165,1 x 76,1 304,8 7,4 304,8 7,4 304,8 7,4
165,1mm x 3 6.500 x 3.500 12.00 16.4 12.00 16.4 12.00 16.4
150 x 80 165,1 x 88,9 304,8 7,4 304,8 7,4 304,8 7,4
165,1mm x 108,0mm 6.500 x 4.252 12.00 16.4 12.00 16.4
- -
150 x 100 165,1 x 108,0 304,8 7,4 304,8 7,4
165,1mm x 4 6.500 x 4.500 12.00 18.0 12.00 18.0 12.00 18.0
150 x 100 165,1 x 114,3 304,8 8,2 304,8 8,2 304,8 8,2
165,1mm x 133,0mm 6.500 x 5.250 12.00 18.0 12.00 18.0
- -
150 x 125 165,1 x 133,0 304,8 8,2 304,8 8,2
165,1mm x 139,7mm 6.500 x 5.500 12.00 18.0 12.00 18.0 12.00 18.0
150 x 125 165,1 x 139,7 304,8 8,2 304,8 8,2 304,8 8,2
165,1mm x 5 6.500 x 5.563 12.00 18.0 12.00 18.0 12.00 18.0
150 x 125 165,1 x 141,3 304,8 8,2 304,8 8,2 304,8 8,2
6x1 6.625 x 1.315 12.00 19.0 12.00 19.0 12.00 19.0
150 x 25 168,3 x 33,4 304,8 8,6 304,8 8,6 304,8 8,6
6 x 1-1/4 6.625 x 1.660 12.00 19.0 12.00 19.0 12.00 19.0
150 x 32 168,3 x 42,4 304,8 8,6 304,8 8,6 304,8 8,6
6 x 1-1/2 6.625 x 1.900 12.00 19.0 12.00 19.0 12.00 19.0
150 x 40 168,3 x 48,3 304,8 8,6 304,8 8,6 304,8 8,6
6x2 6.625 x 2.375 12.00 19.0 12.00 19.0 12.00 19.0
150 x 50 168,3 x 60,3 304,8 8,6 304,8 8,6 304,8 8,6
6 x 2-1/2 6.625 x 2.874 12.00 19.0 12.00 19.0 12.00 19.0
150 x 65 168,3 x 73,0 304,8 8,6 304,8 8,6 304,8 8,6
6 x 76,1mm 6.625 x 3.000 12.00 19.0 12.00 19.0 12.00 19.0
150 x 65 168,3 x 76,1 304,8 8,6 304,8 8,6 304,8 8,6
6x3 6.625 x 3.500 12.00 19.0 12.00 19.0 12.00 19.0
150 x 80 168,3 x 88,9 304,8 8,6 304,8 8,6 304,8 8,6
6 x 108,0mm 6.625 x 4.500 12.00 19.0 12.00 19.0
- -
150 x 100 168,3 x 108,0 304,8 8,6 304,8 8,6
6x4 6.625 x 4.500 12.00 19.0 12.00 19.0 12.00 19.0
150 x 100 168,3 x 114,3 304,8 8,6 304,8 8,6 304,8 8,6
6 x 133,0mm 6.625 x 5.250 12.00 19.0 12.00 19.0
- -
150 x 125 168,3 x 133,0 304,8 8,6 304,8 8,6
6 x 139,7mm 6.625 x 5.500 12.00 19.0 12.00 19.0 12.00 19.0
150 x 125 168,3 x 139,7 304,8 8,6 304,8 8,6 304,8 8,6
6x5 6.625 x 5.563 12.00 19.0 12.00 19.0 12.00 19.0
150 x 125 168,3 x 141,3 304,8 8,6 304,8 8,6 304,8 8,6
216,3mm x 165,1mm 8.516 x 6.500 12.00 21.2 12.00 21.2 12.00 21.2
200 x 150 216,3 x 165,1 304,8 9,6 304,8 9,6 304,8 9,6
216,3mm x 6 8.516 x 6.625 12.00 21.2 12.00 21.2 12.00 21.2
200 x 150 216,3 x 168,3 304,8 9,6 304,8 9,6 304,8 9,6
8 x 165,1mm 8.625 x 6.500 12.00 21.2 12.00 21.2 12.00 21.2
200 x 150 219,1 x 165,1 304,8 9,6 304,8 9,6 304,8 9,6
8x6 8.625 x 6.625 12.00 21.2 12.00 21.2 12.00 21.2
200 x 150 219,1 x 168,3 304,8 9,6 304,8 9,6 304,8 9,6
TABLE 26 (4 OF 4)
FIGURES 397, 398 AND 399 FABRICATED SWAGED NIPPLES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 60 of 64

E to E E to E E to E
E to E

FIGURE 391 FIGURE 392 FIGURE 393 FIGURE 395

FABRICATED FABRICATED FABRICATED FABRICATED HOSE
ADAPTER NIPPLE ADAPTER NIPPLE ADAPTER NIPPLE ADAPTER NIPPLE
GROOVE X MALE THREAD GROOVE X GROOVE GROOVE X PLAIN GROOVE X HOSE
Figures 391 Figures 392 & 393 Figure 395
Nominal Pipe Size Fabricated Adapter Fabricated Adapter Fabricated Hose
Nipple Nipple Adapter Nipple
ANSI O.D. E to E Weight E to E Weight E to E Weight
Inches Inches Inches Lbs. Inches Lbs. Inches Lbs.
DN mm mm kg mm kg mm kg
1 1.315 3.00 0.6 3.00 0.6 3.00 0.4
25 33,4 76,2 0,3 76,2 0,3 76,2 0,2
1-1/4 1.660 4.00 0.8 4.00 0.8 3.63 0.7
32 42,4 101,6 0,4 101,6 0,4 92,1 0,3
1-1/2 1.900 4.00 0.9 4.00 0.9 4.00 0.8
40 48,3 101,6 0,4 101,6 0,4 101,6 0,4
2 2.375 4.00 1.2 4.00 1.2 4.63 1.3
50 60,3 101,6 0,5 101,6 0,5 117,5 0,6
2-1/2 2.874 4.00 1.9 4.00 1.9 5.50 2.1
65 73,0 101,6 0,9 101,6 0,9 139,7 1,0
76,1mm 3.000 4.00 1.9 4.00 1.9 5.50 2.1
65 76,1 101,6 0,9 101,6 0,9 139,7 1,0
3 3.500 4.00 2.5 4.00 6.00 3.3
0,9
80 88,9 101,6 1,1 101,6 152,4 1,5
108,0mm 4.252 6.00 5.0 7.25 5.0
- -
100 108,0 154,4 2,3 184,2 2,3
4 4.500 6.00 5.4 6.00 5.4 7.25 5.5
100 114,3 154,4 2,5 154,4 2,5 184,2 2,5
133,0mm 5.250 6.00 6.9 9.75 6.9
- -
125 133,0 154,4 3,1 247,7 3,1
139,7mm 5.500 6.00 6.00 7.1 9.75 7.1
125 139,7 154,4 154,4 3,2 247,7 3,2
5 5.563 6.00 7.3 6.00 7.3 9.75 8.1
125 141,3 154,4 3,4 154,4 3,4 247,7 3,7
159,0mm 6.250 6.00 8.7 11.00 8.7
- -
150 159,0 154,4 3,9 279,4 3,9
165,1mm 6.500 6.00 9.1 6.00 9.1 11.00 9.1
150 165,1 154,4 4,1 154,4 4,1 279,4 4,1
6 6.625 6.00 9.4 6.00 9.4 11.00 13.2
150 168,3 154,4 4,3 154,4 4,3 279,4 6,0
216,3mm 8.516 6.00 13.8 12.50 21.0
- -
200 216,3 154,4 6,3 317,5 9,5
8 8.625 6.00 14.2 6.00 14.2 12.50 24.0
200 219,1 154,4 6,4 154,4 6,4 317,5 10,9
267,4mm 10.528 8.00 25.0 14.00 29.0
- -
250 267,4 203,2 11,3 355,6 13,2
10 10.750 8.00 27.0 8.00 27.0 14.00 29.0
250 273,0 203,2 12,2 203,2 12,2 355,6 13,2
318,5mm 12.539 8.00 33.0 16.00 46.0
- -
300 318,5 203,2 15,0 406,4 20,9
12 12.750 8.00 33.0 8.00 33.0 16.00 46.0
300 323,9 203,2 15,0 203,2 15,0 406,4 20,9
TABLE 27
FIGURES 391, 392, 393 AND 395 FABRICATED ADAPTER NIPPLES
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 61 of 64

C to TE

C to GE

Nominal Pipe Size Nominal Pipe Size

C to GE C to TE Weight C to GE C to TE Weight
Inches Inches Lbs. Inches Inches Lbs.
ANSI O.D. mm mm kg ANSI O.D. mm mm kg
Inches Inches Inches Inches
DN mm DN mm
1-1/4 1.660 2.75 2.75 0.9 4 4.500 5.00 7.25 9.8
32 42,4 69,9 69,9 0,4 100 114,3 127,0 184,2 4,4
1-1/2 1.900 2.75 2.75 1.2 159,0mm 6.250 6.50 6.50 16.8
40 48,3 69,9 69,9 0,5 150 159,0 165,1 165,1 7,6
2 2.375 3.25 4.25 2.0 165,1mm 6.500 6.50 6.50 17.2
50 60,3 82,6 108,0 0,9 150 165,1 165,1 165,1 7,8
2-1/2 2.874 3.75 3.75 3.1 6 6.625 6.50 6.50 17.6
60 73,0 95,3 95,3 1,4 150 168,3 165,1 165,1 8,0
76,1mm 3.000 3.75 3.75 3.2 1-1/4 1.660 2.75 2.75 1.5
65 76,1 95,3 95,3 1,5 32 42,4 69,9 69,9 0,7
3 3.500 4.25 6.00 5.7 1-1/2 1.900 2.75 2.75 1.9
80 88,9 108,0 152,4 2,6 40 48,3 69,9 69,9 0,9
108,0mm 4.252 5.00 7.25 9.6
100 108,0 127,0 184,2 4,4
TABLE 28
FIGURE 315 FABRICATED
GROOVE X MALE THREAD 90° ELBOW
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS

C to TE

C to GE

Nominal Pipe Size Nominal Pipe Size

C to GE C to TE Weight C to GE C to TE Weight
Inches Inches Lbs. Inches Inches Lbs.
ANSI O.D. mm mm kg ANSI O.D. mm mm kg
Inches Inches Inches Inches
DN mm DN mm
2 2.375 3.25 4.25 3.2 5 5.563 5.50 5.50 22.6
50 60,3 82,6 108,0 1,5 125 141,3 139,7 139,7 10,3
2-1/2 2.874 3.75 3.75 4.0 165,1mm 6.500 6.50 6.50 23.0
65 73,0 95,3 95,3 1,8 150 165,1 165,1 165,1 10,4
76,1mm 3.000 3.75 3.75 4.2 6 6.625 6.50 6.50 23.0
65 76,1 95,3 95,3 1,9 150 168,3 165,1 165,1 10,5
3 3.500 4.25 6.00 6.0 8 8.625 7.75 7.75 38.7
80 88,9 108,0 152,4 2,7 200 219,1 196,9 196,9 17,6
4 4.500 5.00 7.25 11.0 10 10.750 9.00 9.00 72.1
100 114,3 127,0 184,2 5,0 250 273,0 228,6 228,6 32,8
139,7mm 5.500 5.50 5.50 22.2 12 12.750 10.00 10.00 92.5
125 139,7 139,7 139,7 10,1 300 323,9 254,0 254,0 42,0
TABLE 29
FIGURE 320 FABRICATED
GROOVE X GROOVE X MALE THREAD TEE
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 62 of 64

C to E

C to E

Nominal Pipe Size

B Dia.
C to E H
Grooved End Flanged End NPSC Threaded
Inches Inches
Inches OD OD Inches
mm mm
DN Inches Inches mm
mm mm
165,1mm x 4 6.500 4.504 12.00 2.50 1.50
150 x 100 165,1 114,3 304.8 63,5 38,1
6x4 6.625 4.504 12.00 2.50 1.50
150 x 100 168,3 114,3 304,8 63,5 38,1
165,1mm x 5 6.500 5.563 12.50 2.50 1.50
150 x 125 165,1 141,3 317,5 63,5 38,1
6x5 6.625 5.563 12.50 2.50 1.50
150 x 125 168,3 141,3 317,5 63,5 38,1
165mm x 139,7mm 6.500 5.476 12.50 2.50 1.50
150 x 125 165,1 139,1 317,5 63,5 38,1
8 x 139,7mm 8.625 5.476 15.50 3.00 1.50
200 x 125 219,1 139,1 393,7 76,2 38,1
8x5 8.625 5.563 15.50 3.00 1.50
200 x 150 219,1 141,3 393,7 76,2 38,1
8 x 165,1mm 8.625 6.500 15.50 3.00 1.50
200 x 150 219,1 165,1 393,7 76,2 38,1
8x6 8.625 6.625 15.50 3.00 1.50
200 x 150 219,1 168,3 393,7 76,2 38,1
216,3mm x 5 8.516 5.563 15.50 3.00 1.50
200 x 125 216,3 141,3 393,7 76,2 38,1
216,3mm x 6 8.516 6.625 15.50 3.00 1.50
200 x 150 216,3 168,3 393,7 76,2 38,1
216,3mm x 139,7mm 8.516 5.476 15.50 3.00 1.50
200 x 125 216,3 139,1 393,7 76,2 38,1
216,3mm x 165,1mm 8.516 6.500 15.50 3.00 1.50
200 x 150 216,3 165,1 393,7 76,2 38,1
267,4mm x 165,1mm 10.528 6.500 18.50 3.50 1.50
250 x 150 267,4 165,1 469,9 88,9 38,1
267,4mm x 6 10.528 6.625 18.50 3.50 1.50
250 x 150 267,4 168,3 469,9 88,9 38,1
10 x 165,1mm 10.750 6.500 18.50 3.50 1.50
250 x 150 273,0 165,1 469,9 88,9 38,1
10 x 6 10.750 6.625 18.50 3.50 1.50
250 x 150 273,0 168,3 469,9 88,9 38,1
267,4mm x 8 10.528 8.625 19.00 3.50 1.50
250 x 200 267,4 219,1 482,6 88,9 38,1
267,4mm x 216,3mm 10.528 8.516 19.00 3.50 1.50
250 x 200 267,4 216,3 482,6 88,9 38,1
10 x 216,3mm 10.750 8.516 19.00 3.50 1.50
250 x 200 273,0 216,3 482,6 88,9 38,1
10 x 8 10.750 8.625 19.00 3.50 1.50
250 x 200 273,0 219,1 482,6 88,9 38,1
TABLE 30 (1 OF 2)
FIGURE 316 FABRICATED REDUCING BASE SUPPORT 90° ELBOW
GROOVE X FLANGE END
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
 G180
Page 63 of 64

C to E

C to E

Nominal Pipe Size

B Dia.
C to E H
Grooved End Flanged End NPSC Threaded
Inches Inches
Inches OD OD Inches
mm mm
DN Inches Inches mm
mm mm
12 x 216,3mm 12.750 8.516 22.00 4.00 1.50
300 x 200 323,9 216,3 558,8 101,6 38,1
318,5mm x 216,3mm 12.539 8.516 22.00 4.00 1.50
300 x 200 318,5 216,3 558,8 101,6 38,1
318,5mm x 8 12.539 8.625 22.00 4.00 1.50
300 x 200 318,5 219,1 558,8 101,6 38,1
12 x 8 12.750 8.625 22.00 4.00 1.50
300 x 200 323,9 219,1 558,8 101,6 38,1
12 x 267,4mm 12.750 10.528 22.00 4.00 1.50
300 x 250 323,9 267,4 558,8 101,6 38,1
12 x 10 12.750 10.750 22.00 4.00 1.50
300 x 250 323,9 273,1 558,8 101,6 38,1
318,5mm x 267,4mm 12.539 10.528 22.00 4.00 1.50
300 x 250 318,5 267,4 558,8 101,6 38,1
318,5mm x 10 12.539 10.750 22.00 4.00 1.50
300 x 200 318,5 273,1 558,8 101,6 38,1
TABLE 30 (2 OF 2)
FIGURE 316 FABRICATED REDUCING BASE SUPPORT 90° ELBOW
GROOVE X FLANGE END
NOMINAL DIMENSIONS AND APPROXIMATE WEIGHTS
G180
Page 64 of 64

Nominal Pipe Size

Elbows Elbows Tee Tee
Ordering
ANSI O.D.
90°
Feet
45°
Feet
Branch
Feet
Run
Feet
Procedure
Inches Inches m m m m
DN mm GRINNELL Products are available
globally through a network of
1-1/4 1.660 1.9 1.0 4.8 1.9 distribution centers. Visit www.grinnell.
32 42,4 0,6 0,3 1,5 0,6 com for the nearest distributor.
1-1/2 1.900 2.3 1.2 5.8 2.3 When placing an order, indicate the
40 48,3 0,7 0,4 1,8 0,7 full product name. Specify the quan-
2 2.375 3.2 1.6 8.0 3.2 tity, figure number, size, and wall
50 60,3 1,0 0,5 2,5 1,0 thickness.
2-1/2 2.874 3.9 2.0 9.8 3.9
65 73,0 1,2 0,6 3,0 1,2
76,1mm 3.000 4.1 2.1 10.3 4.1
65 76,1 1,2 0,6 3,1 1,2
3 3.500 4.9 2.4 12.2 4.9
80 88,9 1,5 0,7 3,7 1,5
108,0mm 4.252 6.5 3.3 16.3 6.5
100 108,0 2,0 1,0 5,0 2,0
4 4.500 6.5 3.3 16.3 6.5
100 114,3 2,0 1,0 5,0 2,0
133,0mm 5.250 8.0 4.0 20.0 8.0
125 133,0 2,4 1,2 6,1 2,4
139,7mm 5.500 8.0 4.1 20.0 8.0
125 139,7 2,4 1,3 6,1 2,4
5 5.563 8.2 4.1 20.5 8.2
125 141,3 2,5 1,3 6,3 2,5
159,0mm 6.250 9.5 4.8 23.8 9.5
150 159,0 2,9 1,4 7,2 2,9
165,1mm 6.500 9.5 4.8 23.8 9.5
150 165,1 2,9 1,4 7,2 2,9
6 6.625 9.9 5.0 24.8 9.9
150 168,3 3,0 1,5 7,6 3,0
216,3mm 8.516 13.1 6.6 32.8 13.1
200 216,3 4,0 2,0 10,0 4,0
8 8.625 13.1 6.6 32.8 13.1
200 219,1 4,0 2,0 10,0 4,0
10 10.750 16.5 8.3 41.3 16.5
250 273,0 5,0 2,5 12,6 5,0
12 12.750 19.9 9.9 49.7 19.9
300 323,9 6,1 3,0 15,1 6,1
14 14.000 23.0 18.0 67.9 23.0
350 355,6 7,0 5,5 20,7 7,0
16 16.000 25.9 20.0 78.1 25.9
400 406,4 7,9 6,1 23,8 7,9
18 18.000 28.9 23.0 85.0 28.9
450 457,2 8,8 7,0 25,9 8,8
20 20.000 33.1 25.9 100.1 33.1
500 508,0 10,1 7,9 30,5 10,1
24 24.000 40.0 29.9 115.2 40.0
600 609,6 12,2 9,1 35,1 12,2

For the reducing tee branches, use the value that is corresponding to the branch size.
Example:
For 8˝ x 8˝ x 2˝ tee, the branch value of 2˝ is 8.0 feet.
For sizes not listed, interpolate from the values shown.

TABLE 31
FRICTION RESISTANCE
EXPRESSED AS EQUIVALENT STRAIGHT PIPE

GLOBAL HEADQUARTERS | 1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone +1-215-362-0700

Copyright © 2014 Tyco Fire Products, LP. All rights reserved.