INTERNATIONAL ISO

STANDARD 6182-11

First edition
2003-12-01

Fire protection — Automatic sprinkler

systems —
Part 11:
r n
Requirements and test methods for pipe
hangers
h o
i s
n
Protection contre l'incendie — Systèmes d'extinction automatiques du
type sprinkler —

S ý
Partie 11: Exigences et méthodes d'essai relatives aux dispositifs de
fixation des conduites

Reference number
ISO 6182-11:2003(E)

© ISO 2003
ISO 6182-11:2003(E)

PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

r n
h o
i s
ý n
S

© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

 ISO 6182-11:2003(E)

Contents Page

Foreword ............................................................................................................................................................ iv
1 Scope...................................................................................................................................................... 1
2 Normative references ........................................................................................................................... 1
3 Terms and definitions........................................................................................................................... 1
4 Product consistency............................................................................................................................. 4
5 Materials and rod sizes......................................................................................................................... 4
6 Material thicknesses ............................................................................................................................. 4
7 Performance requirements .................................................................................................................. 5
8 Test methods......................................................................................................................................... 7
9

r n
Marking................................................................................................................................................... 9

o
Bibliography ..................................................................................................................................................... 13

s h
n i
S ý

© ISO 2003 — All rights reserved iii

ISO 6182-11:2003(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

n
rights. ISO shall not be held responsible for identifying any or all such patent rights.

r
h o
ISO 6182-11 was prepared by Technical Committee ISO/TC 21, Equipment for fire protection and fire fighting,
Subcommittee SC 5, Sprinkler and water spray extinguishing systems.

i s
ISO 6182 consists of the following parts, under the general title Fire protection — Automatic sprinkler systems:


ý n
Part 1: Requirements and test methods for sprinklers

 S
Part 2: Requirements and test methods for wet alarm valves, retard chambers and water motor alarms

 Part 3: Requirements and test methods for dry pipe valves

 Part 4: Requirements and test methods for quick-opening devices

 Part 5: Requirements and test methods for deluge valves

 Part 7: Requirements and test methods for early suppression fast response (ESFR) sprinklers

 Part 9: Requirements and test methods for water mist nozzles

 Part 11: Requirements and test methods for pipe hangers

The following part is under preparation:

 Part 10: Requirements and test methods for domestic sprinklers

iv © ISO 2003 — All rights reserved

INTERNATIONAL STANDARD ISO 6182-11:2003(E)

Fire protection — Automatic sprinkler systems —

Part 11:
Requirements and test methods for pipe hangers

1 Scope
This part of ISO 6182 specifies performance requirements, test methods and marking requirements for pipe
hangers.

2 Normative references
rn
ho
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
is
ýn
ISO 1460, Metallic coatings — Hot dip galvanized coating on ferrous material — Gravimetric determination of
the mass per unit area

S
ISO 2064, Metallic and other inorganic coatings — Definitions and conventions concerning the measurements
of thickness

ISO 2178, Non-magnetic coatings on magnetic substrates — Measurement of coating thickness — Magnetic
method

ISO 3575:1996, Continuous hot-dip zinc-coated carbon steel sheet of commercial, lock-forming and drawing
qualities

ISO 4998:1996, Continuous hot-dip zinc-coated carbon steel sheet of structural quality

ASTM B568, Standard test method for measurement of coating thickness by X-ray spectrometry

3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.

3.1
band hanger
type of hanger that is adjustable and utilizes a band looped around the pipe

3.1.1
adjustable swivel band hanger
type of band hanger that is adjustable and swivels

3.2
bracket
cantilever-type hanger that is attached directly to a vertical surface of the building structure

© ISO 2003 — All rights reserved 1