Introduction of HIFU

1.Introduction
1.1Purpose

This Instructions for Use manual provides a description of System components, its controls and
displays, instructions for its operation, and other equipment information important to be user.

1.2 Conventions
Note: Notes designate information of special interest.
Caution: Cautions alert the user to precautionary steps necessary to properly operate the system.
Failure to observe these cautions may void the warranty. All procedures are broken down by
numbered steps. Steps must be completed in the sequence they are presented. Bulleted lists
indicate general information about a particular function or procedure. They do not imply a
sequential procedure. Control names are spelled as they are on the system, and they appear in
Bold text.

2. Parameter
Machine size 40*38*25cm
Frequency 50Hz/60Hz
Power output 0.2J-2.0J
Handpiece Standard: Face lifting(1.5mm,3.0mm,4.5mm);
Optional: Body slimming(8.0mm,13.0mm);
Optional: Vagina tightening(3.0mm,4.5mm)
Voltage AC110V-240V
Machine weight about 10kg

3. Accessories picture
4. Instrument Description
4.1 Host Control

Vaginal Handle
HIFU Handle

HIFU Operation Interface

Vents

Vaginal Handle Power

cord/Switch
connector
HIFU Handle
Airbag detection Connector
connector
4.2 Treatment Handle

Treatment Handle Description

Item Description
① Switch button Imaging starts, stop/start treatment
② Work button Indicator light will light when work
③ Lock bit position Lock the cartridges to the handle
④ Cartridges Different cartridges work to different areas
⑤ Cable sheathing Connect the handle to machine

4.3 Cartridges

Cartridges Description
Item description
① Top marker Cartridges Transducers
② Treatment instructions Maximum processing line length and Center mark

Cartridges transducer types

Cartridges transducer Frequency Treatment Depth Image depth Length
DS 7-1.5N 7MHz 1.5mm 0-8mm 25mm
DS 7-3.0N 7MHz 3.0mm 0-8mm 25mm
DS4-4.5N 4MHz 4.5mm 0-8mm 25mm

5. Introduction to Operation

5.1 Click on the interface to enter the next interface(Choose treatment handles)

5.2 Function Interface Introduction

5.2.1 Face interface introduction
 The current
Cartridges
operation count The Total number
of shots

Remaining
Cartridges shots/Total
identification
Spacing adjustment

Length Power

Return to main
interface

5.2.2 Body Interface Introduce The current

The total
Cartridges operation
Remaining number of shots
Cartridges shots/Total count
identification

Spacing
adjustment

Length Power

Return to Main
interface
6. Treatment guidelines
Note: Operation Please follow the instruction

6.1 Safety guidelines for neck treatment

6.2 Safety guidelines for face treatment

7. Cleaning and maintenance

7.1 Clean cartridges and handle

Note: The cartridges is packaged in an antistatic package, Do not touch the chip.
As the cartridges will touch the skin, so please use 70% isopropyl alcohol disinfection the
cartridges. Cartridges and handle need to keep clean and dry. Put the cartridges to packages for
next time use after wipe the accessory.

Note:In order to avoid broke the cartridges , please clean only with the above cleaning method,
do not use acetone or other solvent.

7.2 System maintenance

1)Check if the handle and connector are in good
contact 2)Make sure the cartridge is correctly identified
3)Do not place the handle or cartridge on the floor or other hard surfaces
4)Do not twist the handle cable to avoid damaging the internal wires
5)Use only ultrasonic cooling gel,Do not use other lubricants or emulsions,especially mineral
oil,Avoid damage to the cartridge or circuit.
6)Wipe the cartridges surface after treatment
7)Check the cartridge packaging when using the new cartridge
8)The cartridges has a memory function, After use, please store it separately from magnetic card
or static-charged object
9)Do not insert objects other than the probe into the handle, otherwise it will damage the system
security

Note:Please check the date of the cartridge before use, do not use the expired probe.

8.Taboo crowd
1. Pregnant
2. Heart disease, diabetes, hyperthyroidism patients
3. Patients with advanced cancer
4. Surgical wounds are not healed
5. Injection of botulinum toxin within one year
6. Have unrealistic effect on the patients

9.Safety matters
9.1 Handling safe
The operating system memory precision instrument,Users do not try to move the instrument at a
long distance. The original shock-absorbing package must be used during transportation, or it
may lead to system disorders, the energy output will be affected.

9.2 Electrical safety

The operating system uses 220v power supply, the maximum output Current not more than 10A.

9.3 Operation safety

Keep the system clean and make sure the gel does not contaminate the system.

Introduction of HIFU Vaginal

Introduction
HIFU vaginal is more authoritative than the more high-end anti-shrinking negative instrument,
the treatment is no blood, no wound, no scars, no surgery, can solve the vaginal problem more
effectively. Before using the instrument, please read this manual carefully and strictly follow the
instructions in the manual to operate the instrument.

1.Instrument overview
The Vagina Tightening HIFU System uses an noninvasive ultrasonic focusing technique to focus
on the mucous membrane fibrous layer and muscle layer directly. Using ultrasonic waves as the
energy source and taking advantage of its penetration and focus, the system will send out
ultrasonic energy focusing in the the lamina and muscle fiber layer in a predetermined depth. A
higher intensity of ultrasonic region, called focus region, is formed. In 0.1 second, the temperature
of the region can reach to above 65 ℃ , so the collagen is reorganized and the normal tissue
outside the focal region is undamaged. Therefore, the desired depth layer can obtain the ideal
effect of collagen concentration, reorganization and regeneration. Ultimately, the mysterious effect
of vagina tightening is achieved.

2.Parameter
Frequency 50-60Hz
Maximum power 200w
Treatment cartridges 1.5mm, 3.0mm 4.5mm
Voltage 110v-220v
Packing size 69*64*34cm

3.Name of the components

Vaginal tightening
HIFU handle handle

Vaginal tightening
interface
 Vents

Power cord/Switch

Vaginal Handle
connector Airbag detection
connector HIFU Handle
Connector

4.Interface description
Power
Total length Rotation angle Shot length spacing

Number of shots for

one circle

Number of
rows played

Automatic Saved parameters

operation

remaining Pressure detection

shots/Total
shots

Back to main Handle angle

interface
 Note:After ready,the handle will be lighted, then press start button. If the handle do not light,
press the ready button again.

5.Pressure interface

Return to last Save

interface button

1.Tighten the switch of the pressure before test, Extrusion air bag to increase the value, and then
adjust the switch of the pressure until the value on screen around 20.
2.Put the test head into vaginal ( If needed use some Lubricants). 3.When
test, separate the lags with the distance less than shoulder width.
4.Relax 6 seconds , Natural breathing, press save ,this value will be the before treatment value.
5.After treatment , test again from the step 1 , you will get another value after put the test head
into vaginal, this value will be the after treatment value.
Pressure value Condition of vaginal Sensitivity
tightening
Under 60 Very bad No
60-80 Relatively bad Low
80-120 Normal general
120-160 Good Squirting
Above 160 Very good nymph

6.Treatment heads
The machine equipped with two different depth of the treatment head.
功能头 图片 治疗皮肤的深度及功效
3.0mm of functional head The power reaches the
mucosa tissue directly to
speed the cell activity, making
the collagen newborn and
reorganized and increasing the
mucosa elasticity and contract
the vagina muscle.
4.5mm of functional head The power reaches the SMAS
layer to make heat coagulation
of SMAS, performing the
pulling and SMAS suspension
well, having improvement
from deep to shallow so as to
support the muscle structure,
better helping muscle layer
recover elasticity; and it is
more compact.
Pressure test handle Using the principle of balloon
pressure measurement, test
the vaginal tightness.

7.Operation introduction
1. Before using the apparatus, disinfect and wipe the probe by the detergent; and clean the
water drop on the face;
2. Install the handle in the rotary bracket; and connect the connection wire to the host;
3. Electrify the host, press the power switch to start the apparatus;
4. Select suitable probe and access to the handle; and the display screen can display the
corresponding parameter of the probe;
5. Choose “ROTATING”
6.If needed, enter the next step and select “F.AUTO” function;
7. Coat the ultrasonic wave conductor to the probe energy emitting area (black area);
8. Sleeve the protection coat on the probe; and coat a layer of lubrication and function product
on the outer surface of the protection coat;
9. Click “START” button to enter the working state;
10. Stretch the probe in the end of the vagina; and “0” scale is at the top;
11. Press the button on the handle to send out one wire;
12. Repeat the above step until to finish the step; and reset the handle;
13.After completing the required steps, turn off the power,Remove the protective cover.Clean
the probe and handle with detergent.

8.Notes for use and maintenance

1. After being used, the apparatus must be wiped by cleaning water and disinfected by the
detergent to be saved properly (avoid being damaged by the black film of the probe);
2. Power plug with ground pin must be used before application of this apparatus and ensure that
the power outlet is truly grounded.
3. Ensure the apparatus voltage is suitable; if the local power voltage is not stable, we suggest the
user to increasing the stable voltage matching with the power;
4. For treatment effect of the apparatus and ensuring normal service life, please use the
appointed parts provided by the manufacturer;
5. The apparatus cannot be arranged at the damp place or around the water; and the apparatus
cannot be exposed at the sun place directly;
6. The apparatus cannot close to the strong heat source, because it can affect the apparatus life
and normal usage;
7. It must avoid poor contact when being used in winter or drying weather; and smear the gel on
the face uniformly (flatting by the probe);
8. The medium, such as water, oil and the like cannot enter the apparatus; and it cannot be
knocked and thrown in case of damaging the apparatus;
9. Please clean the probe and cut off the power timely after using the ultrasonic beauty
apparatus.

9.Taboos for apparatus users

This apparatus shall be used with enough caution in the following cases, suggestions from
doctors or professionals are necessary prior to use, some details are listed as follows：
1. Clean the vagina before using the apparatus in case of dirty entering the skin along the
ultrasonic wave or stopping the penetration force of the ultrasonic wave;
2. It is strongly recommended to use medium with certain viscosity to facilitate better fusion
between ultrasound and skin and prevent any reflection arising from gap from hampering
acoustic and energy absorption.
3. Each treatment area cannot be repeated too much; and it can be repeated for three times at
most;
4. The hot degree of the probe is not on behalf of the ultrasonic wave power;
5. The patients cannot use the apparatus unless being permitted by the doctor;
6. Patients with malignant tumor, hemophilia or severe bleeding; hyperthyroid patient,
asthmatics, hypertensive, patients with serious diseases, disease of skin and patients with
infectious diseases;
7. The user with II cervical erosion and medium kysthitis cannot use the apparatus;
8. The user with patients with serious diseases, disease of skin and patients with infectious
diseases cannot use the apparatus;
9. After being treated by the ultrasonic scalpel, please not eat spicy food, not take tub bath
within one week; and you can make love with your lover in the same day.

10. Troubleshooting
1. No display on the on the apparatus interface：Please check if the power plug is inserted well
or the power switch is turned on.
2. The apparatus operates normally but the press key malfunctions: Please check if the power
supply is connected well.
3. When the probe is not flatted with the face, the apparatus shall be automatically closed; and it
can be operated as long as restarting the apparatus.