Conbextra® AT

(Formerly Conbextra Spl.) constructive solutions

Non-shrink, free flow, extra high strength grout

Uses addition, Fosroc offers technical support service to specifiers,

end-users and contractors, as well as onsite technical
Conbextra AT is used for heavy duty support beneath load assistance in locations all over the country.
bearing units especially where high static and dynamic forces
occur. Also as an efficient medium for transferring all Properties
operational loads to the foundation. And for effective grouting
of base plates and bolt pockets of Turbo Generators, Diesel Compressive strength ( N/mm2)
Generating sets, Crane and Transporter Rails even with high
1 day 3days 7days 28days
wheel loadings, Heavy Reciprocating Equipments,
Compressors, Pump sets, Pulverising mills, Metal Shearing Flowable 40 60 70 80
and Processing Machines, Steel Rolling Mill Beds, Cement, (W/P 0.16)
Textile, Granite and Paper Plant machinery.
Note : Cubes cast are kept under restraint before testing, to
Advantages simulate site conditions. Size of the cubes used 70.6mm x
70.6mm x 70.6mm tested at 300C.
Nonshrink : Will continue to occupy the filled space without
Tensile strength : At 28 days tensile strength achieved is
shrinkage. Ensures high level of contact with load bearing
typically 3.5 N/mm2 .
areas. Also helps complete filling without voids. No need
for external aids like rodding, poking, chaining etc. Young's modulus : 28 kN/mm2
Increased strength: Can be used under heavy duty Expansion characteristics : Controlled expansion occurs
machines and equipment with high operational and static in the unset material to ensure that the grout, when cured, will
loads continue to occupy its original volume within the confines of
Prepacked and factory controlled: Consistency and the voids in which it was placed.
reliability ensured. Site batching and blending variations
Unrestrained expansion : Upto 4%
eliminated.
Iron free : No chance of deterioration by uncontrolled rust Time for expansion : Expansion starts 20 minutes after
expansion, corrosion and staining of grout. mixing and will be completed 150 minutes later.
Chloride free : Does not cause corrosion of machine Pressure to restrain plastic expansion: Appro. 0.004N/mm2
parts, anchor bolts etc., in contact with grout
Coefficient of Thermal expansion : 11 x 10 -6 per 0C
Description
Thermal conductivity : 10 W/m0C

Conbextra AT is supplied as a ready-to-use dry powder, Fresh wet density : At flowable consistency 2300kg/m3
requiring only the addition of water to produce a free flowing W/P ratio : Recommended water powder ratio for flowable
non-shrink grout. The material is a blend of specially consistency is 0.16. Total quantity of water required for 25 kg
processed cement, pregraded fillers and additives which bag is 4 litres.
impart :
Flow characteristics : The maximum distance of flow is
High early and final strengths due to very low water
governed by the gap width and the head of the grout. Typical
requirement
data for flow design, assuming grout is poured immediately
Controlled expansion to retain the original volume filled
after mixing, is given in the table below :
even after setting
Free flow characteristics without any segregation and Max. flow distance in mm
bleeding
Grout Gap 50mm 100mm 250mm
Conbextra AT, on setting, will have a microcellular structure Consistency Width head head head
with high frost, fire and oil resistance.
Conbextra® AT

(mm)

Technical Support Flowable 30 200 1000 2000

40 500 1500 2500
Fosroc offers a comprehensive range of high performance, 50 1000 2000 3000
high quality concrete repair and construction products. In
Conbextra® AT

N.B : This table is based on the following factors. Estimating

Temperature : 300C; Water saturated substrate; Minimum
unrestricted flow width : 300mm. Packaging

Conbextra AT is supplied in 25 kg bags.

Application guidelines
Yield

A few DOs and DON'Ts One bag of Conbextra AT will yield 12.5 litres at flowable
consistency
DO's
Shelf life
Measure water precisely
Mix mechanically 6 months when stored under cold dry conditions in unopened
bags.
Use mixed grout within 30 minutes
Clean concrete and steel surfaces thoroughly before Precautions
grouting
Build a strong, carefully designed leakproof shuttering Health & Safety instructions
Start curing when grout reaches 'touch-hard' state - within Conbextra AT is nontoxic, but alkaline in nature. Gloves
4 - 6 hrs. should be worn while handling this product. Splashes of
Cure properly for at least 7 days. grout on the skin or eyes should be washed off with clean
running water. In the event of prolonged irritation, seek
DON'Ts
medical advice.
Mix cement, sand, fibres, admixtures, etc., with
Conbextra AT Additional information
Mix water more than specified The Fosroc range of associated products includes
Pour grout from two sides while grouting base plates. Admixtures, Floorings, Protective coatings, Repair and
Protection systems, sealants and waterproofing compounds
Pour grout from a height
Adhesives & Mining. Separate datasheets are available on
Use vibrators in grout
these products.
Use damaged bags of Conbextra AT

Detailed application procedure will be supplied by Fosroc

on request. ® Denotes the Trade mark of Fosroc International Limtied
Important note :
Fosroc products are guaranteed against defective materials and manufacture and are sold subject
to its standard terms and conditions of sale, copies of which may be obtained on request. Whilst
Fosroc endeavours to ensure that any advice, recommendation specification or information it may
give is accurate and correct, it cannot, because it has no direct or continuous control over where
or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products whether or not in accordance with any advice, specification, recommendation
Fosroc Chemicals (India) Pvt. Ltd. or information given by it.

Head Office telephone fax e-mail

Hafeeza Chamber II Floor, 111/3
++91 80-22240018/120 ++91 80-22233474 [email protected]
K H Road, PBNo. 2744, Bangalore 560027
Website: www.fosroc.com
Regional Offices
Bangalore Mumbai Delhi Kolkata
Shankar House, IV Floor 208/209, Persepolis First floor,1/2 East Patel Nagar 30/B Jodhpur Park
1 & 18, RMV Extension Sector 17, Vashi Opp: Vivek Cinema, Main Patel Rd Ground Floor
Bangalore 560 080 Navi Mumbai 400 703 New Delhi 110 008 Kolkata 700 068
Ph:080-2361 3161/2361 2004 Ph:022-2789 6412/14 Ph:011-25884903/4 Ph: 033 2472 5482
Fax : 080-2361 7454 Fax: 022 - 2789 6413 Fax: 011- 25884422 Fax: 033-2472 9921
email: [email protected] email:[email protected] email:[email protected] email:[email protected]

Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bhubaneshwar : (0674) 2521176 Chennai (044) 24899949/24853383
Chandigarh : (0172) 22639360 Cochin : (0484) 2356668 Coimbatore : (0422) 2472408/2548793 Goa : (0832) 254244657 Guwahati (0361)
22548793 Hyderabad : (040) 27662324/27662425 Hubli (0836) 2254750 Indore : (0731) 2504339/25061477 Jaipur : (0141) 22235349
Lucknow :(0522) 22239044 Nagercoil (04652) 2224849 Nasik (0253) 22313618 Mangalore: (0824) 22272234 Vijayawada : (0866)
2537798 Visakhapatnam : (0891) 2564850 INDIA/2004/0354/A