20DL2C41A,20FL2C41A,20GL2C41A

TOSHIBA HIGH EFFICIENCY DIODE STACK (HED) SILICON EPITAXIAL TYPE

20DL2C41A, 20FL2C41A, 20GL2C41A

Unit: mm
SWITCHING MODE POWER SUPPLY APPLICATION
CONVERTER & CHOPPER APPLICATION

z Repetitive Peak Reverse Voltage : VRRM = 200 V, 300 V, 400 V

z Average Output Rectified Current : IO = 20 A
z Ultra Fast Reverse-Recovery Time : trr = 35 ns (Max)
z Low Switching Losses and Output Noise

ABSOLUTE MAXIMUM RATINGS (Ta = 25°C)

CHARACTERISTIC SYMBOL RATING UNIT

20DL2CZ41A 200
Repetitive Peak
20FL2CZ41A VRRM 300 V
Reverse Voltage
20GL2CZ41A 400
Average Output Rectified Current IO 20 A

Peak One Cycle Surge Forward 100 (50Hz)

IFSM A
Current (Non Repetitive) 110 (60Hz)
Junction Temperature Tj −40~150 °C JEDEC ―
Storage Temperature Range Tstg −40~150 °C JEITA ―
Screw Torque − 0.8 N·m TOSHIBA 2-16D1A
Weight: 4.85g
Note: Using continuously under heavy loads (e.g. the application of high
temperature/current/voltage and the significant change in temperature, etc.) may cause this product to
decrease in the reliability significantly even if the operating conditions (i.e. operating
temperature/current/voltage, etc.) are within the absolute maximum ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report
and estimated failure rate, etc).

POLARITY

MARKING

Abbreviation Code Part No.

20DL2C 20DL2C41A
20FL2C 20FL2C41A
20DL2C Part No. (or abbreviation code)
20GL2C 20GL2C41A
Lot No.

A line indicates
lead (Pb)-free package or
Characteristics lead (Pb)-free finish.
indicator

1 2006-11-08
 20DL2C41A,20FL2C41A,20GL2C41A
ELECTRICAL CHARACTERISTICS (Ta = 25°C)

CHARACTERISTIC SYMBOL TEST CONDITION TYP. MAX UNIT

20DL2C41A ― 0.98
Peak Forward
Voltage 20FL2C41A VFM IFM = 10A ― 1.3 V
(Note 1)
20GL2C41A ― 1.8
Repetitive Peak Reverse
IRRM VRRM = Rated ― 50 μA
Current (Note 1)
Reverse Recovery Time (Note 1) trr IF = 2.0A, di / dt = − 50A / μs ― 35 ns
Forward Recovery Time (Note 1) tfr IF = 1A ― 100 ns
Thermal Resistance Rth (j−c) Total DC, Junction to Case ― 1.5 °C / W

Note 1: A value applied to one cell.

Note 2: trr Test Circuit trr Waveform

Note 3: tfr Test Circuit tfr Waveform

Handling Precaution

The absolute maximum ratings denote the absolute maximum ratings, which are rated values and must not be
exceeded during operation, even for an instant. The following are the general derating methods that we recommend
when you design a circuit with a device.

VRRM: We recommend that the worst case voltage, including surge voltage, be no greater than 80% of the
absolute maximum rating of VRRM for a DC circuit and be no greater than 50% of that of VRRM for
an AC circuit. VRRM has a temperature coefficient of 0.1%/°C. Take this temperature coefficient into
account designing a device at low temperature.

IO: We recommend that the worst case current be no greater than 80% of the absolute maximum rating
of IO. Carry out adequate heat design. If you can’t design a circuit with excellent heat radiation, set
the margin by using an allowable Tamax-IO curve.

This rating specifies the non-repetitive peak current in one cycle of a 50-Hz sine wave, condition angle 180.
Therefore, this is only applied for an abnormal operation, which seldom occurs during the lifespan of the device.

We recommend that a device be used at a Tj of below 120°C under the worst load and heat radiation conditions.

Please refer to the Rectifiers databook for further information.

2 2006-11-08
 20DL2C41A,20FL2C41A,20GL2C41A

3 2006-11-08
 20DL2C41A,20FL2C41A,20GL2C41A

4 2006-11-08
 20DL2C41A,20FL2C41A,20GL2C41A

RESTRICTIONS ON PRODUCT USE 20070701-EN

• The information contained herein is subject to change without notice.

• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.

• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his
document shall be made at the customer’s own risk.

• The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.

• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which
may result from its use. No license is granted by implication or otherwise under any patents or other rights of
TOSHIBA or the third parties.

• Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations
that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses
occurring as a result of noncompliance with applicable laws and regulations.

5 2006-11-08