Scribd
Upload
214 views

Set-Up Guide: Warnings and Cautionary Points

The document provides step-by-step setup instructions for a product. It details 29 setup steps involving removing parts, attaching accessories, connecting cables, and securing covers. Pictures and part labels are provided to illustrate the proper installation process.

Uploaded by

Catalin Comi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
214 views

Set-Up Guide: Warnings and Cautionary Points

The document provides step-by-step setup instructions for a product. It details 29 setup steps involving removing parts, attaching accessories, connecting cables, and securing covers. Pictures and part labels are provided to illustrate the proper installation process.

Uploaded by

Catalin Comi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

MD-0105

UIM11008700 Ver00
R111223K5900-TTEC

SET-UP GUIDE

Warnings and Cautionary Points


• The unpacking and setup procedure shall be done by a qualified service technician.
• Be sure to unplug the power cable of the equipment before installing and setting up the product.
• Disconnect the ground wire after unplugging the power cable. Be sure to connect the ground wire before
plugging the power cable.
• Install the equipment near an outlet. Be sure to wire the power cable securely so as to unplug it easily and not
to trip over it.
• According to the model, these illustrations may differ.

Setup
1. Take out the accessories.

D E

a b

2. Open the cover.

© 2012 TOSHIBA TEC CORPORATION All rights reserved MD-0105

1 / 10
3. Remove the screws and take off the cover.
• Screws: 3

4. Remove the screw and take off the cover.


• Screw: 1

5. Take off [P] while pushing down the levers


[F].
• [F]: 2

F F

© 2012 TOSHIBA TEC CORPORATION All rights reserved MD-0105

2 / 10
6. Place [P] on the workbench and install [E] as
shown in the figure.
• [E]: 4
* When installing, take care of the direction and
place of [E]. E

7. Set and install [D] as shown in the figure.


• [D]: 2
* Push both ends of [D] all the way in.

8. Remove [G] and dispose of it.

© 2012 TOSHIBA TEC CORPORATION All rights reserved MD-0105

3 / 10
9. Remove the special screws and take off [N].
• Special screws: 3
N

10. Remove the clamp and remove the cable.


• Clamp: 1

11. Connect the cable connector to [B].


* Be sure to fix the connector securely to
prevent an insufficient connection.

12. Attach the clamp.


• Clamp: 1 place

© 2012 TOSHIBA TEC CORPORATION All rights reserved MD-0105

4 / 10
13. Attach [B] with [a].
• a: 1

a
B

14. Attach [N] with the special screws.


• Special screws: 3

15. Insert [P].


* Push [P] until it locks.

© 2012 TOSHIBA TEC CORPORATION All rights reserved MD-0105

5 / 10
16. Attach the cover with the screw.
• Screw: 1

17. Remove the screws and take off [H].


• Screws: 2

18. Remove the screws and take off [J].


• Screws: 2
* When taking off [J], pull it in the direction
shown in the figure to remove it from the
hook.
J

© 2012 TOSHIBA TEC CORPORATION All rights reserved MD-0105

6 / 10
19. Lift the portion [L] as shown in the figure.

20. Set [A] and wire the cable properly.

21. Wire the cable of [A] as shown in the figure


and then connect the connector.
* When opening and closing the ADU, be
careful not to catch the cable.

© 2012 TOSHIBA TEC CORPORATION All rights reserved MD-0105

7 / 10
22. Install [J].

23. Attach [A] with [b].


• b: 4

24. Attach [J] with the screws.


• Screws: 2

© 2012 TOSHIBA TEC CORPORATION All rights reserved MD-0105

8 / 10
25. Attach [H] with the screws.
• Screws: 2

26. Lower the portion [L] as shown in the figure.

27. Attach the cover with the screws.


• Screws: 3

© 2012 TOSHIBA TEC CORPORATION All rights reserved MD-0105

9 / 10
28. Close the cover.

29. This is the end of the procedures.

© 2012 TOSHIBA TEC CORPORATION All rights reserved MD-0105

10 / 10

You might also like