Global LCD Panel Exchange Center www.panelook.

com

LC420EQE
Product Specification

SPECIFICATION
FOR
APPROVAL

( ) Preliminary Specification
( ̻ ) Final Specification

Title 42.0” QWUXGA TFT LCD

BUYER LGE SUPPLIER LG Display Co., Ltd.

MODEL *MODEL LC420EQE

SUFFIX PGM1 (RoHS Verified)

SIGNATURE SIGNATURE
APPROVED BY APPROVED BY
DATE DATE

/ O.H. Lee / Team Leader

REVIEWED BY

/ Y.J. Heo / Project Leader

PREPARED BY
/ M.S. Park / Engineer

Please return 1 copy for your confirmation with

TV Product Development Dept.
your signature and comments. LG Display Co., Ltd.

Ver. 1.0 0 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

CONTENTS

Number ITEM Page

COVER 0
CONTENTS
1
RECORD OF REVISIONS 2
1 GENERAL DESCRIPTION
3
2 ABSOLUTE MAXIMUM RATINGS
4
3 ELECTRICAL SPECIFICATIONS
5
3-1 ELECTRICAL CHARACTERISTICS
5
3-2 INTERFACE CONNECTIONS
7
3-3 SIGNAL TIMING SPECIFICATIONS
9
3-4 V by One SIGNAL SPECIFICATIONS 10
3-5 COLOR DATA REFERENCE
12
3-6 POWER SEQUENCE
13
4 OPTICAL SPECIFICATIONS
14
5 MECHANICAL CHARACTERISTICS
20
6 RELIABILITY
23
7 INTERNATIONAL STANDARDS
24
7-1 SAFETY
24
7-2 ENVIRONMENT
24
8 PACKING
25
8-1 INFORMATION OF LCM LABEL
25
8-2 PACKING FORM
25
9 PRECAUTIONS 26
9-1 MOUNTING PRECAUTIONS 26
9-2 OPERATING PRECAUTIONS 26
9-3 ELECTROSTATIC DISCHARGE CONTROL 27
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE 27
9-5 STORAGE 27
9-6 OPERAGING CONDITION GUIDE 27

Ver. 1.0 1 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

RECORD OF REVISIONS

Revision No. Revision Date Page Description

0.1 Mar, 07, 2014 - Preliminary Specification (First Draft)
1.0 May, 21, 2014 CAS Version 1.0 Release
Final Specification

Ver. 1.0 2 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification
1. General Description
The LC420EQE is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode (LED)
b ac k l i g ht s ys t em . T he m a t r i x em p l o ys a - S i T h i n F i lm T r an s is t or a s t he a c t i v e e l em en t .
It is a transmissive display type which is operating in the normally black mode. It has a 41.92 inch diagonally
measured active display area with QWUXGA resolution (2160 vertical by 3840 horizontal pixel array).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arrayed in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 10-bit gray scale signal for each dot.
Therefore, it can present a palette of more than 1.06Bilion colors.
It has been designed to apply the 10-bit 8 Lane V by One interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.

EPI(RGB)
EEPROM
Source Driver Circuit
Data
format Vby1 SCL SDA S1 S3840
1~8lane G1
Bit CN1
select Option
(51pin)
signal Timing Controller
HTPDN
I2C Vby1 Rx + DGA + ODC Control
TFT - LCD Panel
LOCKN
Signals (3840 Ý RGB Ý 2160 pixels)
Vby1
8lane

+12V Power Circuit

Power Signals G2160
Block

LED Anode CN1 (8pin)

Back light Assembly
CN2 (8pin)
LED Cathode

Active Screen Size 41.92 inches(1064.67mm) diagonal

Outline Dimension 944.4mm(H) Ý 543.7mm(V) X 9.2mm(D) (Typ.)
Pixel Pitch 0.24165 mm x 0.24165 mm
Pixel Format 3840 horiz. by 2160 vert. Pixels, RGB stripe arrangement
Color Depth 10bit(D), 1.06Billon colors
Luminance, White 400 cd/m2 (Typ)
Viewing Angle (CR>10) Viewing angle free ( R/L 178 (Min.), U/D 178 (Min.))
Power Consumption Total 54.16W (Typ.) [Logic= 5.76W, LED Backlight=48.4W (IF_cathode=160mA)
Weight 8.0 Kg (Typ.) 8.4(Max.)
Display Mode Transmissive mode, Normally black
Surface Treatment Hard coating(3H), Anti-glare treatment of the front polarizer (Haze 1% Typ.)

Ver. 1.0 3 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

2. Absolute Maximum Ratings

The following items are maximum values which, if exceeded, may cause faulty operation or permanent damage
to the LCD module.

Table 1. ABSOLUTE MAXIMUM RATINGS

Value
Parameter Symbol Unit Notes
Min Max

Power Input Voltage LCD Circuit VLCD -0.3 +14.0 VDC

LED Input Voltage Forward Voltage VF - +64.4 VDC 1

T-Con Option Selection Voltage VLOGIC -0.3 +4.0 VDC

Operating Temperature TOP 0 +50 ¶C

2,3
Storage Temperature TST -20 +60 ¶C

Panel Front Temperature TSUR - +68 ¶C 4

Operating Ambient Humidity HOP 10 90 %RH

2,3
Storage Humidity HST 5 90 %RH

Notes 1. Ambient temperature condition (Ta = 25 r 2 ¶C )

2. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be Max 39¶C, and no condensation of water.
3. Gravity mura can be guaranteed below 40¶C condition.
4. The maximum operating temperatures is based on the test condition that the surface temperature
of display area is less than or equal to 68¶C with LCD module alone in a temperature controlled chamber.
Thermal management should be considered in final product design to prevent the surface temperature of
display area from being over 68୅. The range of operating temperature may be degraded in case of
improper thermal management in final product design.
90%

60
60%

50 Storage
Humidity [(%)RH]

Wet Bulb
Temperature [¶C]
40
40%
Operation
30
20
10
0
10%
5%

-20 0 10 20 30 40 50 60 70 80

Dry Bulb Temperature [¶C]

Ver. 1.0 4 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics

It requires two power inputs. One is employed to power for the LCD circuit. The other Is used for the LED
backlight.

Table 2. ELECTRICAL CHARACTERISTICS

Value
Parameter Symbol Unit Note
Min Typ Max

Circuit :

Power Input Voltage VLCD 10.8 12.0 13.2 VDC

- 480 625 mA 1
Power Input Current ILCD
- 1350 1755 mA 2
T-CON Option Input High Voltage VIH 2.7 - 3.6 VDC
Selection Voltage Input Low Voltage VIL 0 - 0.7 VDC
Power Consumption PLCD - 5.8 7.5 Watt 1

Rush current IRUSH - - 10 A 3

Notes
1. The specified current and power consumption are under the VLCD=12.0V, Ta=25 r 2¶C, fV=60Hz
condition, and mosaic pattern(8 x 6) is displayed and f V is the frame frequency.
2. The current is specified at the maximum current pattern.
3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).
4. Ripple voltage level is recommended under ·5% of typical voltage

White : 1023 Gray

Black : 0 Gray

Mosaic Pattern(8 x 6)

Ver. 1.0 5 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

Table 3. ELECTRICAL CHARACTERISTICS (Continue)

Values
Parameter Symbol Unit Note
Min Typ Max
Backlight Assembly :
Forward Current Anode IF (anode) 480 mAdc ·5%
(one array) Cathode IF (cathode) 152 160 168 mAdc 2, 3
Forward Voltage VF 46.4 50.4 54.4 Vdc 4
Forward Voltage Variation ୞VF 1.7 Vdc 5
Power Consumption PBL 44.5 48.4 52.2 W 6
Burst Dimming Duty On duty 1 100 %
Burst Dimming Frequency 1/T 95 182 Hz 8
LED Array : (APPENDIX-V)
Life Time 30,000 Hrs 7

Notes :The design of the LED driver must have specifications for the LED array in LCD Assembly.
The electrical characteristics of LED driver are based on Constant Current driving type.
The performance of the LED in LCM, for example life time or brightness, is extremely influenced by the
characteristics of the LED Driver. So, all the parameters of an LED driver should be carefully designed.
When you design or order the LED driver, please make sure unwanted lighting caused by the mismatch of the
LED and the driver (no lighting, flicker, etc) has never been occurred. When you confirm it, the LCD–
Assembly should be operated in the same condition as installed in your instrument.
1. Electrical characteristics are based on LED Array specification.
2. Specified values are defined for a Backlight Assembly. (IBL :2 LED array/LCM)
3. Each LED array has two anode terminal and six cathode terminals.
The forward current(IF) of the anode terminal is 480mA and it supplies 160mA into three strings, respectively
1string(16 LED PKG)

480mA Cathode #1
¶¶¶
160mA
¶¶¶

Anode#1 1 Array (3 Strings)

¶¶¶ Cathode #3
160mA

480mA Cathode #1
¶¶¶
160mA
¶¶¶

Anode#1 1 Array (3 Strings)

¶¶¶ Cathode #3
160mA

4. The forward voltage(VF) of LED array depends on ambient temperature (Appendix-V)

5. ǻVF means Max VF-Min VF in one Backlight. So VF variation in a Backlight isn’t over Max. 1.7V
6. Maximum level of power consumption is measured at initial turn on.
Typical level of power consumption is measured after 1hrs aging at 25 r 2¶C.
7. The life time(MTTF) is determined as the time at which brightness of the LED is 50% compared to that of
initial value at the typical LED current on condition of continuous operating at 25 r 2¶C, based on duty 100%.
8. The reference method of burst dimming duty ratio.
It is recommended to use synchronous V-sync frequency to prevent waterfall
(Vsync * 2 =Burst Frequency)
Though PWM frequency is over 182Hz (max252Hz), function of backlight is not affected.

Ver. 1.0 6 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification
3-2. Interface Connections
This LCD module employs two kinds of interface connection, 51-pin connector is used for the module
electronics and two 8-pin connectors are used for the integral backlight system.
3-2-1. LCD Module
- LCD Connector(CN1): FI-RE51S-HF(manufactured by JAE) or GT05P-51S-H38(manufactured by LSM)
or IS050-C51B-C39(manufactured by UJU)
- Mating Connector : FI-R51HL(manufactured by JAE) or compatible

Table 4. MODULE CONNECTOR(CN1) PIN CONFIGURATION

No Symbol Description No Symbol Description
1 VLCD Power Supply +12.0V 27 GND Ground
2 VLCD Power Supply +12.0V 28 Rx0n V-by-One HS Data Lane 0
3 VLCD Power Supply +12.0V 29 Rx0p V-by-One HS Data Lane 0
4 VLCD Power Supply +12.0V 30 GND Ground
5 VLCD Power Supply +12.0V 31 Rx1n V-by-One HS Data Lane 1
6 VLCD Power Supply +12.0V 32 Rx1p V-by-One HS Data Lane 1
7 VLCD Power Supply +12.0V 33 GND Ground
8 VLCD Power Supply +12.0V 34 Rx2n V-by-One HS Data Lane 2
9 NC NO CONNECTION 35 Rx2p V-by-One HS Data Lane 2
10 GND Ground 36 GND Ground
11 GND Ground 37 Rx3n V-by-One HS Data Lane 3
12 GND Ground 38 Rx3p V-by-One HS Data Lane 3
13 GND Ground 39 GND Ground
14 NC NO CONNECTION (Note3) 40 Rx4n V-by-One HS Data Lane 4
15 Data format 0 Input Data Format [1:0] : 41 Rx4p V-by-One HS Data Lane 4
‘00’=Mode1, ’01’=Mode2,
16 Data format 1 42 GND Ground
’10’=Mode3, ’11’=Mode4
17 NC NO CONNECTION (Note3) 43 Rx5n V-by-One HS Data Lane 5
18 SDA SDA (For Local dimming) 44 Rx5p V-by-One HS Data Lane 5
19 SCL SCL (For Local dimming) 45 GND Ground
20 NC NO CONNECTION (Note3) 46 Rx6n V-by-One HS Data Lane 6
21 Bit SEL ‫׎‬H‫ ׏‬or NC= 10bit(D) , ‫׎‬L‫ = ׏‬8bit 47 Rx6p V-by-One HS Data Lane 6
22 L-DIM Enable ‘H’ = Enable , ‘L’ or NC = Disable 48 GND Ground
‫׎‬H’ or NC : AGP
23 AGP or NSB 49 Rx7n V-by-One HS Data Lane 7
‫׎‬L’ : NSB (No signal Black)
24 GND Ground 50 Rx7p V-by-One HS Data Lane 7
25 HTPDN Hot plug detect 51 GND Ground
26 LOCKN Lock detect - - -
Note
1. All GND (ground) pins should be connected together to the LCD module’s metal frame.
2. All Input levels of V-by-One signals are based on the V-by-One-HS Standard Version 1.4
3. #14, #17, #20 NC(No Connection) : These pins are used only for LGD (Do not connect)
4. About specific pin(#15, #16), Please see the Appendix VII.
5. Specific pin No. #23 is used for “No signal detection” of system signal interface.
It should be GND for NSB (No Signal Black) while the system interface signal is not.
If this pin is “H”, LCD Module displays AGP (Auto Generation Pattern).

Ver. 1.0 7 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

3-2-2. Backlight Module

[ CN201 ] [ CN202 ]
1) LED Array assy Connector (Plug) 1) LED Array assy Connector (Plug)
: HS100-L08N-N62 (black color, manufactured by UJU) : HS100-L08N-N62-A (natural color, manufactured by UJU)
2) Mating Connector (Receptacle) 2) Mating Connector (Receptacle)
: IS100-L08T-C46 (black color, manufactured by UJU) : IS100-L08T-C46-A (natural color, manufactured by UJU)

Table 5. BACKLIGHT CONNECTOR PIN CONFIGURATION(CN201,CN202)

No Symbol Description Note No Symbol Description Note

1 L1 Cathode LED Input Current LED Input Current for

1 Anode_R
R1~R3
2 L2 Cathode LED Output Current
2 N.C Open
3 L3 Cathode LED Output Current
3 N.C Open
4 N.C Open
4 N.C Open
5 N.C Open
5 N.C Open
6 N.C Open
6 R3 Cathode LED Output Current
7 N.C Open
7 R2 Cathode LED Output Current
LED Input Current for
8 Anode_L
8 R1 Cathode LED Output Current
L1~L3

Ver. 1.0 8 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

3-3. Signal Timing Specifications

Table 6 shows the signal timing required at the input of the Vx1 transmitter. All of the interface signal timings
should be satisfied with the following specification for normal operation.

Table 6. TIMING TABLE (DE Only Mode)

ITEM Symbol Min Typ Max Unit Note

Display
Period tHV 480 480 480 tCLK 3840/8

Horizontal Blank tHB 50 70 120 tCLK 1

Total tHP 530 550 600 tCLK

Display
Period tVV 2160 2160 2160 Lines

Vertical Blank tVB 40 90 600 Lines 1

Total tVP 2200 2250 2760 Lines

ITEM Symbol Min Typ Max Unit Note

DCLK fCLK 60 74.25 78.00 MHz 594/8

Frequency Horizontal fH 121.8 135 140 KHz 2

Vertical fV 47 60 63 Hz 2

notes: 1. The input of HSYNC & VSYNC signal does not have an effect on normal operation (DE Only Mode).
If you use spread spectrum of EMI, add some additional clock to minimum value for clock margin.

2. The performance of the electro-optical characteristics may be influenced by variance of the vertical
refresh rate and the horizontal frequency

୔ Timing should be set based on clock frequency.

Ver. 1.0 9 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

3-4. V by One input signal Characteristics

3-4-1. V by One Input Signal Timing Diagram

1UI = 1/(Serial data rate)

ื ื B C

Y
ื
A
ื D Y=0mV

ื ื F E
X

X=0 UI X=1 UI

Table7. Eye Mask Specification

X[UI] Note Y[mV] Note

A 0.25 (max) 2 0 -

B 0.3 (max) 2 50 3

C 0.7(min) 3 50 3

D 0.75(min) 3 0 -

E 0.7(min) 3 l -50 l 3

F 0.3(max) 2 l -50 l 3

notes 1. All Input levels of V by One signals are based on the V by One HS Standard Ver. 1.4
2. This is allowable maximum value.
3. This is allowable minimum value.
4. The eye diagram is measured by the oscilloscope and receiver CDR characteristic must be
emulated.
- PLL bandwidth : 20 Mhz
- Damping Factor : 1.5

Ver. 1.0 10 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

3-4-2. V by One Input Signal Characteristics

1) DC Specification

}y{o
}yj{
}y{s

Description Symbol Min Max Unit

CML Differential input High threshold VRTH - 50 mV
CML Differential input Low threshold VRTL -50 - mV
CML common mode Bias Voltage VRCT 0.6 0.8 V
2) AC Specification

Vdiff =0
Lane0

tRISK_INTER
Lane1 Vdiff =0

<Inter-pair Skew between two Lanes>

1H
T-CON
Max 1 DE
V By One Rx IP
Hblank Rx1 Rx2
Rx1 Vblank
DE (Sub Block) (Sub Block)

Vblank
Rx2 4 Lane 4 Lane
DE

<Inter-pair Skew between two sub Blocks> <TCON – VbyOne Brief Diagram >

Description Symbol Min Max Unit notes

Allowable inter-pair skew between lanes tRISK_INTER - 5 UI 1,3
Allowable iner-pair skew between sub-blocks tRISK_BLOCK - 1 DE 1,4

Notes 1.1UI = 1/serial data rate

2. it is the time difference between the true and complementary single-ended signals.
3. it is the time difference of the differential voltage between any two lanes in one sub block.
4. it is the time difference of the differential voltage between any two blocks in one IP.

Ver. 1.0 11 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification
3-5. Color Data Reference
The brightness of each primary color (red, green, blue) is based on the 10bit or 8bit gray scale data input for the color.
The higher binary input, the brighter the color. Table 8 provides a reference for color versus data input.

Table 8. COLOR DATA REFERENCE

Packer input & Unpacker output 30bpp RGB (10bit) 24bpp RGB (8bit)
D[0] R[2] R[0]

D[1] R[3] R[1]

D[2] R[4] R[2]

D[3] R[5] R[3]

Byte0
D[4] R[6] R[4]

D[5] R[7] R[5]

D[6] R[8] R[6]

D[7] R[9] R[7]

D[8] G[2] G[0]

D[9] G[3] G[1]

D[10] G[4] G[2]

D[11] G[5] G[3]

Byte1
D[12] G[6] G[4]

D[13] G[7] G[5]

D[14] G[8] G[6]

D[15] G[9] G[7]

D[16] B[2] B[0]

D[17] B[3] B[1]

D[18] B[4] B[2]

D[19] B[5] B[3]

Byte2
D[20] B[6] B[4]

D[21] B[7] B[5]

D[22] B[8] B[6]

D[23] B[9] B[7]

D[24] Don’t care

D[25] Don’t care

D[26] B[0]

D[27] B[1]
Byte3
D[28] G[0]

D[29] G[1]

D[30] R[0]

D[31] R[1]

Ver. 1.0 12 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

3-6. Power Sequence

3-6-1. LCD Driving circuit

Power Supply For LCD

VLCD

Interface Signal (Tx_clock)

User Control Signal

(DATA FORMAT, BIT_SEL)

Power for LED

Table 9. POWER SEQUENCE

Value
Parameter Unit Note
Min Typ Max
T1 0.5 - 20 ms 1
T2 0 - - ms 2
T3 400 - - ms 3
T4 100 - - ms 3
T5 1.0 - - s 4
T6 0 - T2 ms 5
T7 0 - - ms 6

1. Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
Note : 2. If T2 is satisfied with specification after removing LVDS Cable, there is no problem.
3. The T3 / T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.
4. T5 should be measured after the Module has been fully discharged between power off and on period.
5. If the on time of signals (Interface signal and user control signals) precedes the on time of Power (VLCD),
it will be happened abnormal display. When T6 is NC status, T6 doesn’t need to be measured.
6. It is recommendation specification that T7 has to be 0ms as a minimum value.
୔ Please avoid floating state of interface signal at invalid period.
୔ When the power supply for LCD (VLCD) is off, be sure to pull down the valid and invalid data to 0V.

Ver. 1.0 13 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environmentࣜat 25·2¶C.
The values are specified at distance 50cm from the LCD surface at a viewing angle of ) and T equal to 0 ¶.
FIG. 1 shows additional information concerning the measurement equipment and method.

LCD Module Pritchard 880 or

Optical Stage(x,y)
equivalent

50cm
FIG. 1 Optical Characteristic Measurement Equipment and Method

Ta= 25·2¶C, VLCD=12.0V, fV=60Hz, Dclk=74.25MHz,

Table 10. OPTICAL CHARACTERISTICS IF_cathode=160mA

Value
Parameter Symbol Unit notes
Min Typ Max
Contrast Ratio CR 800 1200 - 1
Surface Luminance, white LWH 320 400 - cd/m2 2
Luminance Variation G WHITE 9P 65 - - % 3
Variation G to G ı 6 9 5
Response Time
Gray to Gray (BW) G to G BW 8 12 ms 4
Rx 0.648
RED
Ry 0.332
Gx 0.309
GREEN
Color Coordinates Gy Typ 0.604 Typ
[CIE1931] Bx -0.03 0.153 +0.03
BLUE
By 0.053
Wx 0.281
WHITE
Wy 0.288
Color Temperature 10,000 K
Color Gamut 72 %
Viewing Angle (CR>10)
x axis, right(I=0¶) Tr 89 - -
x axis, left (I=180¶) Tl 89 - -
degree 6
y axis, up (I=90¶) Tu 89 - -
y axis, down (I=270¶) Td 89 - -
Gray Scale - - - 7

Ver. 1.0 14 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification
Note : 1. Contrast Ratio(CR) is defined mathematically as :
Surface Luminance with all white pixels
Contrast Ratio =
Surface Luminance with all black pixels
It is measured at center 1-point.
2. Surface luminance are determined after the unit has been ‘ON’ and 1 Hour after lighting the
backlight in a dark environment at 25·2¶C. Surface luminance is the luminance value at center
1-point across the LCD surface 50cm from the surface with all pixels displaying white.
For more information see the FIG. 2.
3. The variation in surface luminance , G WHITE is defined as :
G WHITE(9P) = Minimum (Lon1,Lon2~ Lon8, Lon9) / Maximum (Lon1,Lon2~ Lon8, Lon9)*100
Where Lon1 to Lon9 are the luminance with all pixels displaying white at 9 locations .
For more information, see the FIG. 2.
4. Response time is the time required for the display to transit from any gray to white (Rise Time, Tr R)
and from any gray to black (Decay time, TrD). For additional information see the FIG. 3.
୔ G to GBW Spec stands for average value of all measured points.
Photo Detector : RD-80S / Field : 2 ¶
5. G to G ı is Variation of Gray to Gray response time composing a picture

G to G (ı) =
¥ Ȉ(Xi- u)2
N
Xi = Individual Data
u = Data average
N : The number of Data
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD module surface. For more information, see the FIG. 4.

7. Gray scale specification

Gamma Value is approximately 2.2. For more information, see the Table 10

Table 11. GRAY SCALE SPECIFICATION

Gray Level Luminance [%] (Typ)
L0 0.083
L63 0.27
L127 1.04
L191 2.49
L255 4.68
L319 7.66
L383 11.5
L447 16.1
L511 21.6
L575 28.1
L639 35.4
L703 43.7
L767 53.0
L831 63.2
L895 74.5
L959 86.7
L1023 100

Ver. 1.0 15 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

Measuring point for surface luminance & measuring point for luminance variation.

H
A H/2
B

ྚ ྛ ྜ

V/2
ྜྷ ྙ ྞ
V

A : H / 9 mm
B : V / 9 mm
ྟ ྠ ྡ
@ H,V : Active Area

FIG. 2 9 Points for Luminance Measure

Response time is defined as the following figure and shall be measured by switching the input signal for
“Gray(N)” and “Black or White”.

Ver. 1.0 16 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

Dimension of viewing angle range

Normal
E Y
I = 90q, Up

I = 180q, Left
T

I = 0q, Right

I = 270q, Down

FIG. 4 Viewing Angle

Ver. 1.0 17 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

5. Mechanical Characteristics

Table 12 provides general mechanical characteristics.

Table 12. MECHANICAL CHARACTERISTICS

Item Value

Horizontal 944.4 mm

Outline Dimension Vertical 543.7 mm

Depth 9.2 mm

Horizontal 944.4 mm
Bezel Area
Vertical 533.2 mm

Horizontal 927.94 mm
Active Display Area
Vertical 521.96 mm

Weight 8.0Kg (Typ), 8.4(Max.)

notes : Please refer to a mechanical drawing in terms of tolerance at the next page.

Ver. 1.0 18 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

[ FRONT VIEW ]

SET : TOP



     





$FWLYH$UHD



$FWLYH$UHD







 
$ 



   



127(
8QVSHFLILHGWROHUDQFHLVPP
0D[7RUTXH5HIHUWRWDEOH
0D[GHSWK5HIHUWRWDEOH
7KHVDPHIHDWXUHPHDQVWKHVDPHGLPHQVLRQ
'HVLJQHU
VDSSURYDOLVUHTXLUHGEHIRUHPDVVSURGXFWLRQ
7KLVGUDZLQJLVRQO\SUHOLPLUDU\GDWDDQGFDQEHFKDQJHG


 

0D[



6(&7,21$$  

6WDQG3(01XW
6&$/(

6&$/(

Ver. 1.0 19 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

[ REAR VIEW ] SET : TOP

 

  

 

D D   D D

 





K
J J N O


G H


 






D
P









M M F







J J






I



G G H






Q


Q Q










R


R 
S S

E E

 

 

 

 

 

 

SET : DOWN

8'0+HLJKW 0D['HSWK 7RUTXH

,WHP 7DS 1RWHV
PP PP .JIFP
D 0   0D[
E 0   0D[
F 0   0D[
G 0   0D[
H 0   0D[
I 0   0D[
J 0   0D[
K 0   0D[
L 0   0D[
M 0   0D[
N 0   0D[
O 0   0D[
P 0   0D[
Q 0   0D[
R 0   0D[
S 0   0D[

Ver. 1.0 20 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

6. Reliability
Table 13. ENVIRONMENT TEST CONDITION

No. Test Item Condition

1 High temperature storage test Ta= 60¶C 90% 240h

2 Low temperature storage test Ta= -20¶C 240h

3 High temperature operation test Ta= 50¶C 50%RH 500h

4 Low temperature operation test Ta= 0¶C 500h

Wave form : random

Vibration level : 0.5Grms
Vibration test
5 Bandwidth : 10-300Hz
(non-operating)
Duration : X,Y,Z,
Each direction per 10 min

Shock level : 5G
Shock test Waveform : half sine wave, 11ms
6
(non-operating) Direction : ᇹX, ᇹY, ᇹZ
One time each direction

7 Humidity condition Operation Ta= 40 ¶C ,90%RH

Altitude operating 0 - 16,400 ft

8
storage / shipment 0 - 40,000 ft

9 Panel Push Test (Module Condition) Max 6kgf (Test Method : Note 2)

Note : 1. Before and after Reliability test, LCM should be operated with normal function.
2. Panel Push Test Method

Ver. 1.0 21 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

7. International Standards
7-1. Safety
a) UL 60065, Underwriters Laboratories Inc.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
b) CAN/CSA-C22.2 No. 60065-03, Canadian Standards Association.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
c) EN 60065, European Committee for Electrotechnical Standardization (CENELEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
d) IEC 60065, The International Electrotechnical Commission (IEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.

7-2. Environment
a) RoHS, Directive 2011/65/EU of the European Parliament and of the council of 8 June 2011

Ver. 1.0 22 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

8. Packing
8-1. Information of LCM Label
a) Lot Mark

A B C D E F G H I J K L M

A,B,C : SIZE(INCH) D : YEAR

E : MONTH F ~ M : SERIAL NO.

Note
1. YEAR
Year 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020

Mark A B C D E F G H J K

2. MONTH

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
Mark 1 2 3 4 5 6 7 8 9 A B C

b) Location of Lot Mark

Serial NO. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one Pallet : 22 pcs

b) Pallet Size : 1300 mm(W) X 1140 mm(D) X 763 mm(H)

Ver. 1.0 23 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

9. Precautions
Please pay attention to the followings when you use this TFT LCD module.
9-1. Mounting Precautions
(1) You must mount a module using specified mounting holes (Details refer to the drawings).
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress, Concentrated stress)
is not applied to the module. And the case on which a module is mounted should have sufficient strength
so that external force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzine. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.

9-2. Operating Precautions

(1) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(2) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on)
becomes longer
(3) Be careful for condensation at sudden temperature change.Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(4) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(5) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
(6) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can’t be operated
its full characteristics perfectly.
(7) A screw which is fastened up the steels should be a machine screw.
(if not, it can causes conductive particles and deal LCM a fatal blow)
(8) Please do not set LCD on its edge.
(9) The conductive material and signal cables are kept away from LED driver inductor to prevent abnormal
display, sound noise and temperature rising.

Ver. 1.0 24 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

9-3. Electrostatic Discharge Control

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5¶C and 35¶C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
(3) Storage condition is guaranteed under packing conditions.
(4) The phase transition of Liquid Crystal in the condition of the low or high storage temperature will be
recovered when the LCD module returns to the normal condition.

Ver. 1.0 25 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

# APPENDIX-I
̰ Pallet Ass’y

NO. DESCRIPTION MATERIAL

1 LCD Module 42” LCD
2 BAG AL
3 TAPE MASKING 20MMX50M
4 PALLET Plastic 1300X1140X120.0mm
5 PACKING,BOTTOM EPS
6 PACKING,TOP EPS
7 ANGLE,PACKING PAPER
8 BAND PP
9 ANGLE,COVER PAPER
10 BAND STEEL OR PP
11 LABEL YUPO 80G 100X70

Ver. 1.0 26 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

# APPENDIX- II-1

‫ غ‬LCM Label

LC420EQE
Model
(PG)(M1)

SH Special Handling Mark

Serial No.
LIGHT GUIDE : >SMMA<
UL, TUV Mark

LGD Logo Origin

̰ w™–‹œŠ›–•Gš›Œ
TGsnGkš—“ˆ GOwˆ‘œPGj–USGs{k
TGsnGkš—“ˆ GOnœˆ•Ž¡–œPGj–USGs{k
TGsnGkš—“ˆ GOwˆ‘œSGoŒŒšœ•ŽPGjvUSGs{k
•–›ŒšGXU{ŒG–™Ž•G–GsjtGsˆ‰Œ“Gž““G‰ŒGŠˆ•ŽŒ‹GˆŠŠ–™‹•ŽG›–G›ŒG—™–‹œŠ›–•Gš›ŒUG

Ver. 1.0 27 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

# APPENDIX- II-2

‫ غ‬Pallet Label

LC420EQE
PGM1
22PCS 001/01-01
MADE IN KOREA RoHS Verified

XXXXXXXXXXXXX XXX

Ver. 1.0 28 / 37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

# APPENDIX- III
̰ Required signal assignment for Flat Link (Thine : THCV216) Transmitter

TX’s Inner Structure

Packer Scrambler 8/10b Encoder Serializer

8 H H j j
D[31:24] G G h h
8 F F g g
8 Tx_n
D[23:16] PD[7:0] PD[7:0] E E f f
D D i i
8 Tx_p
C C e e
D[15:8] d d
B B
8 A A c c
D[7:0] b b
D/K D/K a a

Timing diagram of the Serializer

First Last
a b c d e i f g h g

time

Timing
THCV216 FI-RE51(41)S-HF
Controller
or Compatible
100nF
8
Tx_n Rx_n
D[31:24]

8 100nF
D[23:16] Tx_p Rx_p
Tx’s
8 Inner
D[15:8] Strucure HTPDN HTPDN
8
D[7:0]
LOCKN LOCKN

VCC

notes: 1. The LCD module uses a 100 nF capacitor on positive and negative lines of each receiver input.
2. Refer to Vx1 Transmitter Data Sheet for detail descriptions. (THCV216 or Compatible)
3. About Module connector pin configuration, Please refer to the Page 8~9.

Ver. 1.0 29 / 37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

# APPENDIX- IV-1
‫ غ‬Option Pin Circuit Block Diagram

1) Circuit Block Diagram of Data format Selection pin

Data format Select Pin : Pin 15, Pin16

1KŸ
Data format Select
Data format Select
(Pin 15,16)

75kŸ

ASIC
(TCON)

System Side LCM Side

2) Circuit Block Diagram of Bit Selection pin

Bit Select Pin : Pin 21

VCC

75kŸ
1KŸ
Bit Select
Bit Select
(Pin 21)

ASIC
(TCON)

System Side LCM Side

Ver. 1.0 30 / 37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

# APPENDIX- IV-2
‫ غ‬Option Pin Circuit Block Diagram

3) Circuit Block Diagram of AGP Selection pin

AGP(auto Generation Pattern ) or NSB (no signal black) : Pin 23

FI-RE51S-HF
}ŠŠGaGZUZ}G

10kŸ
pin 1kŸ
#23

R1 ” 1kŸ 60kŸ
(0Ÿ recommand)

ASIC
(TCON)

System Side LCM Side

Ver. 1.0 31 / 37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

# APPENDIX- VI-1

‫ غ‬input mode of pixel data

Mode 1 : Non-Division Mode 2 : 2 Division

Lane 1st Data 2nd Data Data# Lane 1st Data 2nd Data Data#

Lane0 1 9 3833 Lane0 1 5 1917

Lane1 2 10 3834 Lane1 2 6 1918

Lane2 3 11 3835 Lane2 3 7 1919

Lane3 4 12 3836 Lane3 4 8 1920

Lane4 5 13 3837 Lane4 1921 1925 3837

Lane5 6 14 3838 Lane5 1922 1926 3838

Lane6 7 15 3839 Lane6 1923 1927 3839

Lane7 8 16 3840 Lane7 1924 1928 3840

Ver. 1.0 32 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

# APPENDIX- VI-2

‫ غ‬input mode of pixel data

Mode 3 : 4 Division Mode 4 : 8 Division

Lane 1st Data 2nd Data Data# Lane 1st Data 2nd Data Data#

Lane0 1 3 959 Lane0 1 2 480

Lane1 2 4 960 Lane1 481 482 960

Lane2 961 963 1919 Lane2 961 962 1440

Lane3 962 964 1920 Lane3 1441 1442 1920

Lane4 1921 1923 2879 Lane4 1921 1922 2400

Lane5 1922 1924 2880 Lane5 2401 2402 2880

Lane6 2881 2883 3839 Lane6 2881 2882 3360

Lane7 2882 2884 3840 Lane7 3361 3362 3840

Ver. 1.0 33 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LC420EQE
Product Specification

# APPENDIX- VII
‫ غ‬LED Array Electrical Spec

‫ غ‬Forward Current vs. Forward Voltage

‫ غ‬Ambient Temperature vs. Forward Voltage

Ver. 1.0 34 /37

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com