DESIGN OF SLAB

A slab system shall be designed by any procedure satisfying conditions of

equilibrium and geometric compatibility, if shown that the design strength at every
section is at least equal to the required strength and that of all serviceability conditions
including limits on deflections are met.
Design of slab systems for gravity loads including the slab and beams between
supports and supporting columns and walls forming orthogonal frames by either direct
method or equivalent frame method shall be permitted.
For lateral loads, analysis of frames shall take into account effects of cracking and
reinforcement on stiffness of frame members.

SLAB 1:

6m

S1 4m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
( 4+6)(2)
h¿ = 111.111 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Office 2.40 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 7.310 kN

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 WU 16.800 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
Fy 276.0 MPa
f'c 21.0 MPa
Β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 4: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.65 0.70 0.667

Ca,neg 0.085 0.081 0.0837
Cb,neg 0.015 0.019 0.0163

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.65 0.70 0.667

Ca,pos,dl 0.05 0.046 0.0487
Cb,pos,dl 0.009 0.011 0.0097
Ca,pos,ll 0.062 0.057 0.0603
Cb,pos,ll 0.011 0.014 0.0121

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 22.499 kN-m Ms 4.820 kN-m
Mb,neg 9.858 kN-m Ml 2.168 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 7.407 kN-m Mb,pos,dl 3.319 kN-m
Ma,pos,ll 7.053 kN-m Mb,pos,ll 3.184 kN-m
Ma,pos,total 14.460 kN-m Mb,pos,total 6.503 kN-m

SUMMARY OF SLAB-1

SUMMARY
SHORT DIRECTION LONG DIRECTION
S–1
Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 22.499 14.46 4.82 9.858 6.503 2.168 kN-m
H 150 150 150 150 150 150
D 124 124 124 124 118 124
Rn 1.62584 1.04492 0.34831 0.71237 0.51893 0.15667
Req'd ρ 0.00619 0.00390 0.00127 0.00263 0.00191 0.00057
use ρ 0.00619 0.00507 0.00507 0.00507 0.00507 0.00507
As 767.560 628.680 628.680 628.680 598.260 628.680
Req'd s 145 180 180 180 190 180
use s 145 180 180 180 190 180

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 SLAB 2:
6m

S2 4m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
( 4+6)(2)
h¿ = 111.111 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Office 2.40 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 7.310 kN
WU 16.800 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
Fy 276.0 MPa
f'c 21.0 MPa
Β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 9: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.65 0.70 0.667

Ca,neg 0.083 0.081 0.0823
Cb,neg 0.008 0.011 0.0090

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.65 0.70 0.667

Ca,pos,dl 0.034 0.033 0.0337
Cb,pos,dl 0.005 0.006 0.0053
Ca,pos,ll 0.054 0.05 0.0528
Cb,pos,ll 0.009 0.011 0.0096

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 22.122 kN-m Ms 3.767 kN-m
Mb,neg 5.443 kN-m Ml 1.447 kN-m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 5.126 kN-m Mb,pos,dl 1.814 kN-m
Ma,pos,ll 6.175 kN-m Mb,pos,ll 2.526 kN-m
Ma,pos,total 11.301 kN-m Mb,pos,total 4.340 kN-m

SUMMARY OF SLAB-2

SUMMARY
SHORT DIRECTION LONG DIRECTION
S-2 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 22.122 11.301 3.767 5.443 4.34 1.447 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.59860 0.81664 0.27221 0.39333 0.34632 0.10456
Req'd ρ 0.00608 0.00303 0.00099 0.00144 0.00127 0.00038
use ρ 0.00608 0.00507 0.00507 0.00507 0.00507 0.00507
As 753.920 628.680 628.680 628.680 598.260 628.680
Req'd s 150 180 180 180 190 180
use s 150 180 180 180 190 180

SLAB 3:
6m

S3 6m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(6+ 6)(2)
h¿ = 133.333 mm
180

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Conference room 7.20 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 15.470 kN
WU 25.000 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 6.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 CASE 4: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 1.00 1.00 1.000

Ca,neg 0.05 0.05 0.0500
Cb,neg 0.05 0.05 0.0500

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 1.00 1.00 1.000

Ca,pos,dl 0.027 0.027 0.0270
Cb,pos,dl 0.027 0.027 0.0270
Ca,pos,ll 0.032 0.032 0.0320
Cb,pos,ll 0.032 0.032 0.0320

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 45.000 kN-m Ms 9.020 kN-m
Mb,neg 45.000 kN-m Ml 9.020 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 9.240 kN-m Mb,pos,dl 9.240 kN-m
Ma,pos,ll 17.821 kN-m Mb,pos,ll 17.821 kN-m
Ma,pos,total 27.061 kN-m Mb,pos,total 27.061 kN-m

SUMMARY OF SLAB-3

SHORT DIRECTION LONG DIRECTION

S-3 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 45 27.061 9.02 45 27.061 9.020 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 3.25182 1.95550 0.65181 3.25182 2.15942 0.65181
Req'd ρ 0.01311 0.00752 0.00241 0.01311 0.00836 0.00241
use ρ 0.01311 0.00752 0.00507 0.01311 0.00836 0.00507
As 1625.640 932.809 628.680 1625.752 987.064 628.680
Req'd s 70 120 180 70 115 180

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
use s 70 120 180 70 115 180

SLAB 4:

5m

S4
6m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(6+5)(2)
h¿ = 122.2222 mm
180
instead use h = 150mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Computer use 4.80 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 11.390 kN
WU 20.900 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 5.00 m

Typical floor 150 mm

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.80 0.85 0.833

Ca,neg 0.055 0.049 0.0510
Cb,neg 0.041 0.046 0.0443

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.80 0.85 0.833

Ca,pos,dl 0.032 0.029 0.0300
Cb,pos,dl 0.015 0.017 0.0163
Ca,pos,ll 0.044 0.04 0.0414
Cb,pos,ll 0.019 0.022 0.0210

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 26.648 kN-m Ms 6.306 kN-m
Mb,neg 33.331 kN-m Ml 4.730 kN-m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 7.130 kN-m Mb,pos,dl 5.578 kN-m
Ma,pos,ll 11.789 kN-m Mb,pos,ll 8.611 kN-m
Ma,pos,total 18.919 kN-m Mb,pos,total 14.189 kN-m

SUMMARY OF SLAB-4

SUMMARY
SHORT DIRECTION LONG DIRECTION
S-4 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 26.648 18.919 6.306 33.331 14.189 4.730 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.92566 1.36714 0.45569 2.40859 1.13226 0.34180
Req'd ρ 0.00740 0.00516 0.00167 0.00941 0.00424 0.00125
use ρ 0.00740 0.00516 0.00507 0.00941 0.00507 0.00507
As 917.600 639.738 628.680 1167.035 598.260 628.680
Req'd s 125 175 180 95 190 180
use s 125 175 180 95 190 180

SLAB 5:

5m

S5 4m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
( 4+5)(2)
h¿ = 100 mm
180
instead use h = 150 mm

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Computer use 4.80 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 11.390 kN
WU 20.900 kN

CLEAR SPAN
Long direction 5.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
Fy 276.0 MPa
f'c 21.0 MPa
Β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 USING COEFFICIENT METHOD:
CASE 2: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.80 0.80 0.800

Ca,neg 0.065 0.065 0.0650
Cb,neg 0.027 0.027 0.0270

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.80 0.80 0.800

Ca,pos,dl 0.026 0.026 0.0260
Cb,pos,dl 0.011 0.011 0.0110
Ca,pos,ll 0.041 0.041 0.0410
Cb,pos,ll 0.017 0.017 0.0170

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 21.736 kN-m Ms .000 kN-m
Mb,neg 14.108 kN-m Ml .000 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 3.954 kN-m Mb,pos,dl 2.614 kN-m
Ma,pos,ll 7.472 kN-m Mb,pos,ll 4.841 kN-m
Ma,pos,total 11.426 kN-m Mb,pos,total 7.455 kN-m

SUMMARY OF SLAB-5

SHORT DIRECTION LONG DIRECTION

S-5 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 21.736 11.426 0 14.108 7.455 .000 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.57070 0.82567 0.00000 1.01948 0.59490 0.00000
Req'd ρ 0.00597 0.00306 0.00000 0.00381 0.00219 0.00000

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 use ρ 0.00597 0.00507 NA 0.00507 0.00507 NA
As 740.280 628.680 NA 628.680 598.260 NA
Req'd s 155 180 NA 180 190 NA
use s 155 180 NA 180 190 NA

SLAB 6:

5m

S6 4m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(5+ 4)(2)
h¿ = 100 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Computer use 4.80 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 11.390 kN
WU 20.900 kN

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 CLEAR SPAN
Long direction 5.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.80 0.80 0.800

Ca,neg 0.055 0.055 0.0550
Cb,neg 0.041 0.041 0.0410

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.80 0.80 0.800

Ca,pos,dl 0.032 0.032 0.0320
Cb,pos,dl 0.015 0.015 0.0150
Ca,pos,ll 0.044 0.044 0.0440
Cb,pos,ll 0.019 0.019 0.0190

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 18.392 kN-m Ms 4.295 kN-m
Mb,neg 21.423 kN-m Ml 2.992 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 4.867 kN-m Mb,pos,dl 3.565 kN-m
Ma,pos,ll 8.019 kN-m Mb,pos,ll 5.410 kN-m
Ma,pos,total 12.886 kN-m Mb,pos,total 8.975 kN-m

SUMMARY OF SLAB-6

SUMMARY
SHORT DIRECTION LONG DIRECTION
S-6 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 18.392 12.886 4.295 21.423 8.975 2.992 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.32906 0.93118 0.31037 1.54808 0.71619 0.21621
Req'd ρ 0.00501 0.00347 0.00113 0.00588 0.00265 0.00079
use ρ 0.00507 0.00507 0.00507 0.00588 0.00507 0.00507
As 628.680 628.680 628.680 728.615 598.260 628.680
Req'd s 180 180 180 155 190 180
use s 180 180 180 155 190 180

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 SLAB 7:

5m

S7 4m 4m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(5+ 4)(2)
h¿ = 100 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Computer use 4.80 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 11.390 kN
WU 20.900 kN

CLEAR SPAN
Long direction 5.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 9: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.80 0.80 0.800

Ca,neg 0.075 0.075 0.0750
Cb,neg 0.017 0.017 0.0170

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.80 0.80 0.800

Ca,pos,dl 0.029 0.029 0.0290
Cb,pos,dl 0.01 0.01 0.0100
Ca,pos,ll 0.042 0.042 0.0420
Cb,pos,ll 0.017 0.017 0.0170

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 25.080 kN-m Ms 4.022 kN-m
Mb,neg 8.883 kN-m Ml 2.406 kN-m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 4.411 kN-m Mb,pos,dl 2.377 kN-m
Ma,pos,ll 7.654 kN-m Mb,pos,ll 4.841 kN-m
Ma,pos,total 12.065 kN-m Mb,pos,total 7.218 kN-m

SUMMARY OF SLAB-7

SUMMARY
SHORT DIRECTION LONG DIRECTION
S-7 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 25.08 12.065 4.022 8.883 7.218 2.406 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.81235 0.87185 0.29064 0.64191 0.57598 0.17386
Req'd ρ 0.00694 0.00324 0.00106 0.00237 0.00212 0.00063
use ρ 0.00694 0.00507 0.00507 0.00507 0.00507 0.00507
As 860.560 628.680 628.680 628.680 598.260 628.680
Req'd s 130 180 180 180 190 180
use s 130 180 180 180 190 180

SLAB 8:

6.0 m

S8
6.0 m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
MINIMUM THICKNESS OF SLAB:
perimeter of the panel
h¿
180
(6+ 6)(2)
h¿ = 133.333 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2010

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
--- 0.00 kPa
Restroom 2.40 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 4.080 kN
WU 13.600 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 6.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 1.00 1.00 1.000

Ca,neg 0.033 0.033 0.0330
Cb,neg 0.061 0.061 0.0610

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 1.00 1.00 1.000

Ca,pos,dl 0.02 0.02 0.0200
Cb,pos,dl 0.023 0.023 0.0230
Ca,pos,ll 0.028 0.028 0.0280
Cb,pos,ll 0.03 0.03 0.0300

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 16.157 kN-m Ms 3.652 kN-m
Mb,neg 29.866 kN-m Ml 4.092 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 6.844 kN-m Mb,pos,dl 7.871 kN-m
Ma,pos,ll 4.113 kN-m Mb,pos,ll 4.406 kN-m
Ma,pos,total 10.957 kN-m Mb,pos,total 12.277 kN-m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 SUMMARY OF SLAB-8

SUMMARY
SHORT DIRECTION LONG DIRECTION
S-8 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 16.157 10.957 3.652 29.866 12.277 4.092 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.16755 0.79178 0.26390 2.15820 0.97968 0.29570
Req'd ρ 0.00438 0.00294 0.00096 0.00836 0.00365 0.00108
use ρ 0.00507 0.00507 0.00507 0.00836 0.00507 0.00507
As 628.680 628.680 628.680 1036.623 598.260 628.680
Req'd s 180 180 180 110 190 180
use s 180 180 180 110 190 180

SLAB 9:

6.0 m

S9 4.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
( 4.0+ 6.0)(2)
h¿ = 111.111 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Hallway 4.80 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 11.390 kN
WU 20.900 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 2: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.65 0.70 0.667

Ca,neg 0.077 0.074 0.0760
Cb,neg 0.014 0.017 0.0150

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.65 0.70 0.667

Ca,pos,dl 0.032 0.03 0.0313
Cb,pos,dl 0.006 0.007 0.0063
Ca,pos,ll 0.053 0.049 0.0518
Cb,pos,ll 0.01 0.012 0.0106

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 25.414 kN-m Ms .000 kN-m
Mb,neg 11.286 kN-m Ml .000 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 4.761 kN-m Mb,pos,dl 2.156 kN-m
Ma,pos,ll 9.440 kN-m Mb,pos,ll 4.346 kN-m
Ma,pos,total 14.201 kN-m Mb,pos,total 6.502 kN-m

SUMMARY OF SLAB-9

SUMMARY
SHORT DIRECTION LONG DIRECTION
S-9 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 25.414 14.201 0 11.286 6.502 .000 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.83648 1.02620 0.00000 0.81556 0.51885 0.00000
Req'd ρ 0.00704 0.00383 0.00000 0.00303 0.00191 0.00000
use ρ 0.00704 0.00507 NA 0.00507 0.00507 NA

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 As 872.960 628.680 NA 628.680 598.260 NA
Req'd s 130 180 NA 180 190 NA
use s 130 180 NA 180 190 NA

SLAB 10:

6.0 m

S10 4m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
( 4.0+ 6.0)(2)
h¿ = 111.111 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Dining Room 4.80 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 11.390 kN
WU 20.900 kN

CLEAR SPAN
Long direction 6.00 m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.65 0.70 0.667

Ca,neg 0.074 0.068 0.0720
Cb,neg 0.024 0.029 0.0257

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.65 0.70 0.667

Ca,pos,dl 0.044 0.04 0.0427
Cb,pos,dl 0.009 0.011 0.0097
Ca,pos,ll 0.059 0.054 0.0573
Cb,pos,ll 0.011 0.014 0.0121

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 24.077 kN-m Ms 5.645 kN-m
Mb,neg 19.337 kN-m Ml 2.760 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 6.494 kN-m Mb,pos,dl 3.319 kN-m
Ma,pos,ll 10.442 kN-m Mb,pos,ll 4.961 kN-m
Ma,pos,total 16.936 kN-m Mb,pos,total 8.280 kN-m

SUMMARY OF SLAB-10

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 10 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 24.077 16.936 5.645 19.337 8.28 2.760 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.73987 1.22384 0.40792 1.39734 0.66073 0.19945
Req'd ρ 0.00665 0.00460 0.00150 0.00528 0.00244 0.00073
use ρ 0.00665 0.00507 0.00507 0.00528 0.00507 0.00507
As 824.600 628.680 628.680 654.500 598.260 628.680
Req'd s 135 180 180 175 190 180
use s 135 180 180 175 190 180

SLAB 11:

6.0 m

S11 4m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
MINIMUM THICKNESS OF SLAB:
perimeter of the panel
h¿
180
(6 .0+ 4.0)(2)
h¿ = 111.111 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Office 2.40 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 7.310 kN
WU 16.800 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.65 0.70 0.667

Ca,neg 0.074 0.068 0.0720
Cb,neg 0.024 0.029 0.0257

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.65 0.70 0.667

Ca,pos,dl 0.044 0.04 0.0427
Cb,pos,dl 0.009 0.011 0.0097
Ca,pos,ll 0.059 0.054 0.0573
Cb,pos,ll 0.011 0.014 0.0121

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 19.354 kN-m Ms 4.399 kN-m
Mb,neg 15.543 kN-m Ml 2.168 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 6.494 kN-m Mb,pos,dl 3.319 kN-m
Ma,pos,ll 6.702 kN-m Mb,pos,ll 3.184 kN-m
Ma,pos,total 13.196 kN-m Mb,pos,total 6.503 kN-m

SUMMARY OF SLAB-11

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 11 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 19.354 13.196 4.399 15.543 6.503 2.168 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.39857 0.95358 0.31788 1.12318 0.51893 0.15667
Req'd ρ 0.00528 0.00355 0.00116 0.00421 0.00191 0.00057
use ρ 0.00528 0.00507 0.00507 0.00507 0.00507 0.00507
As 654.720 628.680 628.680 628.680 598.260 628.680
Req'd s 175 180 180 180 190 180
use s 175 180 180 180 190 180

SLAB 12:

5.0 m

S12 4m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(5.0+ 4 .0)(2)
h¿ = 100 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Basic Floor Area 1.90 kPa
Office 2.40 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 7.310 kN
WU 16.800 kN

CLEAR SPAN
Long direction 5.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 4: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.80 0.80 0.800

Ca,neg 0.071 0.071 0.0710
Cb,neg 0.029 0.029 0.0290

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.80 0.80 0.800

Ca,pos,dl 0.039 0.039 0.0390
Cb,pos,dl 0.016 0.016 0.0160
Ca,pos,ll 0.048 0.048 0.0480
Cb,pos,ll 0.02 0.02 0.0200

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 19.085 kN-m Ms 3.849 kN-m
Mb,neg 12.180 kN-m Ml 2.486 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 5.932 kN-m Mb,pos,dl 3.802 kN-m
Ma,pos,ll 5.614 kN-m Mb,pos,ll 3.655 kN-m
Ma,pos,total 11.546 kN-m Mb,pos,total 7.457 kN-m

SUMMARY OF SLAB-12

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 12 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 19.085 11.546 3.849 12.18 7.457 2.486 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.37913 0.83435 0.27814 0.88016 0.59506 0.17965
Req'd ρ 0.00521 0.00310 0.00102 0.00327 0.00219 0.00065
use ρ 0.00521 0.00507 0.00507 0.00507 0.00507 0.00507
As 646.040 628.680 628.680 628.680 598.260 628.680
Req'd s 175 180 180 180 190 180
use s 175 180 180 180 190 180

SLAB 13:

6.0 m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 S13 4m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(5.0+3.0)(2)
h¿ = 111.111 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.19 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
Office 2.40 kPa
FACTORED LOADS
1.4WD 9.506 kN
1.7WL 7.310 kN
WU 16.800 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.65 0.70 0.667

Ca,neg 0.074 0.068 0.0720
Cb,neg 0.024 0.029 0.0257

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.65 0.70 0.667

Ca,pos,dl 0.044 0.04 0.0427
Cb,pos,dl 0.009 0.011 0.0097
Ca,pos,ll 0.059 0.054 0.0573
Cb,pos,ll 0.011 0.014 0.0121

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 19.354 kN-m Ms 4.399 kN-m
Mb,neg 15.543 kN-m Ml 2.168 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 6.494 kN-m Mb,pos,dl 3.319 kN-m
Ma,pos,ll 6.702 kN-m Mb,pos,ll 3.184 kN-m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Ma,pos,total 13.196 kN-m Mb,pos,total 6.503 kN-m

SUMMARY OF SLAB-13

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 13 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 19.354 13.196 4.399 15.543 6.503 2.168 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.39857 0.95358 0.31788 1.12318 0.51893 0.15667
Req'd ρ 0.00528 0.00355 0.00116 0.00421 0.00191 0.00057
use ρ 0.00528 0.00507 0.00507 0.00507 0.00507 0.00507
As 654.720 628.680 628.680 628.680 598.260 628.680
Req'd s 175 180 180 180 190 180
use s 175 180 180 180 190 180

SLAB 14:

6.0 m

S14 4.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(5.0+3.5)(2)
h¿ = 111.111 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN
WU 12.500 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 4: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.65 0.70 0.667

Ca,neg 0.085 0.081 0.0837
Cb,neg 0.015 0.019 0.0163

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.65 0.70 0.667

Ca,pos,dl 0.05 0.046 0.0487
Cb,pos,dl 0.009 0.011 0.0097
Ca,pos,ll 0.062 0.057 0.0603
Cb,pos,ll 0.011 0.014 0.0121

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 16.740 kN-m Ms 3.439 kN-m
Mb,neg 7.335 kN-m Ml 1.545 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 7.200 kN-m Mb,pos,dl 3.227 kN-m
Ma,pos,ll 3.116 kN-m Mb,pos,ll 1.407 kN-m
Ma,pos,total 10.316 kN-m Mb,pos,total 4.634 kN-m

SUMMARY OF SLAB-14

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 14 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 16.74 10.316 3.439 7.335 4.634 1.545 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.20968 0.74546 0.24851 0.53005 0.36979 0.11165
Req'd ρ 0.00454 0.00276 0.00091 0.00195 0.00135 0.00041
use ρ 0.00507 0.00507 0.00507 0.00507 0.00507 0.00507
As 628.680 628.680 628.680 628.680 598.260 628.680

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
Req'd s 180 180 180 180 190 180
use s 180 180 180 180 190 180

SLAB 15:

6.0 m

S15 4.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(5.0+3.5)(2)
h¿ = 111.111 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN
WU 12.500 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 4.00 m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Typical floor 150 mm
Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 9: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.65 0.70 0.667

Ca,neg 0.083 0.081 0.0823
Cb,neg 0.008 0.011 0.0090

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.65 0.70 0.667

Ca,pos,dl 0.034 0.033 0.0337
Cb,pos,dl 0.005 0.006 0.0053
Ca,pos,ll 0.054 0.05 0.0528
Cb,pos,ll 0.009 0.011 0.0096

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Ma,neg 16.460 kN-m Ms 2.570 kN-m
Mb,neg 4.050 kN-m Ml 0.960 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 4.982 kN-m Mb,pos,dl 1.763 kN-m
Ma,pos,ll 2.729 kN-m Mb,pos,ll 1.116 kN-m
Ma,pos,total 7.711 kN-m Mb,pos,total 2.879 kN-m

SUMMARY OF SLAB-15

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 15 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 16.46 7.711 2.57 4.05 2.879 .960 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.18944 0.55722 0.18572 0.29266 0.22974 0.06937
Req'd ρ 0.00446 0.00205 0.00068 0.00107 0.00084 0.00025
use ρ 0.00507 0.00507 0.00507 0.00507 0.00507 0.00507
As 628.680 628.680 628.680 628.680 598.260 628.680
Req'd s 180 180 180 180 190 180
use s 180 180 180 180 190 180

SLAB 16:

6.0 m

S16 6.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 (6.0+6.0)(2)
h¿ = 133.333 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN
WU 12.500 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 6.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 USING COEFFICIENT METHOD:
CASE 4: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 1.00 1.00 1.000

Ca,neg 0.05 0.05 0.0500
Cb,neg 0.05 0.05 0.0500

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 1.00 1.00 1.000

Ca,pos,dl 0.027 0.027 0.0270
Cb,pos,dl 0.027 0.027 0.0270
Ca,pos,ll 0.032 0.032 0.0320
Cb,pos,ll 0.032 0.032 0.0320

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 22.500 kN-m Ms 4.234 kN-m
Mb,neg 22.500 kN-m Ml 4.234 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 8.981 kN-m Mb,pos,dl 8.981 kN-m
Ma,pos,ll 3.721 kN-m Mb,pos,ll 3.721 kN-m
Ma,pos,total 12.702 kN-m Mb,pos,total 12.702 kN-m

SUMMARY OF SLAB-16

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 16 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
Moment 22.5 12.702 4.234 22.5 12.702 4.234 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.62591 0.91788 0.30596 1.62591 1.01360 0.30596
Req'd ρ 0.00619 0.00342 0.00112 0.00619 0.00378 0.00112
use ρ 0.00619 0.00507 0.00507 0.00619 0.00507 0.00507
As 767.560 628.680 628.680 767.177 598.260 628.680
Req'd s 145 180 180 145 190 180
use s 145 180 180 145 190 180

SLAB 17:

5.0 m

S17 6.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(6.0+5.0)(2)
h¿ = 122.222 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 WU 12.500 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 5.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.80 0.85 0.833

Ca,neg 0.055 0.049 0.0510
Cb,neg 0.041 0.046 0.0443

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.80 0.85 0.833

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Ca,pos,dl 0.032 0.029 0.0300
Cb,pos,dl 0.015 0.017 0.0163
Ca,pos,ll 0.044 0.04 0.0414
Cb,pos,ll 0.019 0.022 0.0210

NEGATIVE MOMENTS

Ma,neg 15.938 kN-m Ms 3.424 kN-m

Mb,neg 19.935 kN-m Ml 2.621 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 6.930 kN-m Mb,pos,dl 5.422 kN-m
Ma,pos,ll 3.343 kN-m Mb,pos,ll 2.442 kN-m
Ma,pos,total 10.273 kN-m Mb,pos,total 7.864 kN-m

SUMMARY OF SLAB-17

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 17 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 15.938 10.273 3.424 19.935 7.864 2.621 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.15172 0.74235 0.24743 1.44056 0.62753 0.18940
Req'd ρ 0.00432 0.00275 0.00090 0.00545 0.00232 0.00069
use ρ 0.00507 0.00507 0.00507 0.00545 0.00507 0.00507
As 628.680 628.680 628.680 675.670 598.260 628.680
Req'd s 180 180 180 165 190 180
use s 180 180 180 165 190 180

SLAB 18:

6.0 m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 S18 4.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
( 4 .0+5.0)(2)
h¿ = 100 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN
WU 12.500 kN

CLEAR SPAN
Long direction 5.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 2: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.80 0.80 0.800

Ca,neg 0.065 0.065 0.0650
Cb,neg 0.027 0.027 0.0270

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.80 0.80 0.800

Ca,pos,dl 0.026 0.026 0.0260
Cb,pos,dl 0.011 0.011 0.0110
Ca,pos,ll 0.041 0.041 0.0410
Cb,pos,ll 0.017 0.017 0.0170

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 13.000 kN-m Ms .000 kN-m
Mb,neg 8.438 kN-m Ml .000 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 3.844 kN-m Mb,pos,dl 2.541 kN-m
Ma,pos,ll 2.119 kN-m Mb,pos,ll 1.373 kN-m
Ma,pos,total 5.963 kN-m Mb,pos,total 3.914 kN-m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 SUMMARY OF SLAB-18

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 18 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 13 5.963 0 8.438 3.914 .000 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 0.93941 0.43090 0.00000 0.60975 0.31233 0.00000
Req'd ρ 0.00350 0.00158 0.00000 0.00225 0.00114 0.00000
use ρ 0.00507 0.00507 NA 0.00507 0.00507 NA
As 628.680 628.680 NA 628.680 598.260 NA
Req'd s 180 180 NA 180 190 NA
use s 180 180 NA 180 190 NA

SLAB 19:

5.0 m

S19 4.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
( 4.0+ 5.0)(2)
h¿ = 100 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN
WU 12.500 kN

CLEAR SPAN
Long direction 5.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.80 0.80 0.800

Ca,neg 0.055 0.055 0.0550

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Cb,neg 0.041 0.041 0.0410

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.80 0.80 0.800

Ca,pos,dl 0.032 0.032 0.0320
Cb,pos,dl 0.015 0.015 0.0150
Ca,pos,ll 0.044 0.044 0.0440
Cb,pos,ll 0.019 0.019 0.0190

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 11.000 kN-m Ms 2.335 kN-m
Mb,neg 12.813 kN-m Ml 1.666 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 4.731 kN-m Mb,pos,dl 3.465 kN-m
Ma,pos,ll 2.274 kN-m Mb,pos,ll 1.534 kN-m
Ma,pos,total 7.005 kN-m Mb,pos,total 4.999 kN-m

SUMMARY OF SLAB-19

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 19 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 11 7.005 2.335 12.813 4.999 1.666 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 0.79489 0.50620 0.16873 0.92590 0.39891 0.12039
Req'd ρ 0.00295 0.00186 0.00061 0.00345 0.00146 0.00044
use ρ 0.00507 0.00507 0.00507 0.00507 0.00507 0.00507
As 628.680 628.680 628.680 628.680 598.260 628.680
Req'd s 180 180 180 180 190 180
use s 180 180 180 180 190 180

SLAB 20:

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 6.0 m

S20 6.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(6.0+6.0)(2)
h¿ = 133.333 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN
WU 12.500 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 6.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 1.00 1.00 1.000

Ca,neg 0.033 0.033 0.0330
Cb,neg 0.061 0.061 0.0610

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 1.00 1.00 1.000

Ca,pos,dl 0.02 0.02 0.0200
Cb,pos,dl 0.023 0.023 0.0230
Ca,pos,ll 0.028 0.028 0.0280
Cb,pos,ll 0.03 0.03 0.0300

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 14.850 kN-m Ms 3.303 kN-m
Mb,neg 27.450 kN-m Ml 3.713 kN-m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 6.653 kN-m Mb,pos,dl 7.651 kN-m
Ma,pos,ll 3.256 kN-m Mb,pos,ll 3.488 kN-m
Ma,pos,total 9.909 kN-m Mb,pos,total 11.139 kN-m

SUMMARY OF SLAB-20

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 20 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 14.85 9.909 3.303 27.45 11.139 3.713 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.07310 0.71605 0.23868 1.98361 0.88887 0.26831
Req'd ρ 0.00401 0.00265 0.00087 0.00764 0.00331 0.00098
use ρ 0.00507 0.00507 0.00507 0.00764 0.00507 0.00507
As 628.680 628.680 628.680 947.115 598.260 628.680
Req'd s 180 180 180 120 190 180
use s 180 180 180 120 190 180

SLAB 21:

5.0 m

S21 4.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
( 4.0+ 5.0)(2)
h¿ = 100 mm
180
instead use h = 150 mm

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN
WU 12.500 kN

CLEAR SPAN
Long direction 5.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 CASE 4: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.80 0.80 0.800

Ca,neg 0.071 0.071 0.0710
Cb,neg 0.029 0.029 0.0290

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.80 0.80 0.800

Ca,pos,dl 0.039 0.039 0.0390
Cb,pos,dl 0.016 0.016 0.0160
Ca,pos,ll 0.048 0.048 0.0480
Cb,pos,ll 0.02 0.02 0.0200

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 14.200 kN-m Ms 2.749 kN-m
Mb,neg 9.063 kN-m Ml 1.770 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 5.766 kN-m Mb,pos,dl 3.696 kN-m
Ma,pos,ll 2.481 kN-m Mb,pos,ll 1.615 kN-m
Ma,pos,total 8.247 kN-m Mb,pos,total 5.311 kN-m

SUMMARY OF SLAB-21

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 21 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 14.2 8.247 2.749 9.063 5.311 1.770 kN-m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.02613 0.59595 0.19865 0.65492 0.42381 0.12790
Req'd ρ 0.00383 0.00220 0.00072 0.00242 0.00155 0.00047
use ρ 0.00507 0.00507 0.00507 0.00507 0.00507 0.00507
As 628.680 628.680 628.680 628.680 598.260 628.680
Req'd s 180 180 180 180 190 180
use s 180 180 180 180 190 180

SLAB 22:

6.0 m

S22 4.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(6.0+ 4.0)(2)
h¿ = 111.111 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN
WU 12.500 kN

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 CLEAR SPAN
Long direction 6.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.65 0.70 0.667

Ca,neg 0.074 0.068 0.0720
Cb,neg 0.024 0.029 0.0257

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.65 0.70 0.667

Ca,pos,dl 0.044 0.04 0.0427
Cb,pos,dl 0.009 0.011 0.0097
Ca,pos,ll 0.059 0.054 0.0573

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 Cb,pos,ll 0.011 0.014 0.0121

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 14.400 kN-m Ms 3.091 kN-m
Mb,neg 11.565 kN-m Ml 1.545 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 6.313 kN-m Mb,pos,dl 3.227 kN-m
Ma,pos,ll 2.961 kN-m Mb,pos,ll 1.407 kN-m
Ma,pos,total 9.274 kN-m Mb,pos,total 4.634 kN-m

SUMMARY OF SLAB-22

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 22 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 14.4 9.274 3.091 11.565 4.634 1.545 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.04058 0.67016 0.22336 0.83572 0.36979 0.11165
Req'd ρ 0.00389 0.00248 0.00081 0.00310 0.00135 0.00041
use ρ 0.00507 0.00507 0.00507 0.00507 0.00507 0.00507
As 628.680 628.680 628.680 628.680 598.260 628.680
Req'd s 180 180 180 180 190 180
use s 180 180 180 180 190 180

SLAB 23:

6.0 m

S18 4.0 m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
MINIMUM THICKNESS OF SLAB:
perimeter of the panel
h¿
180
( 4.0+ 6.0)(2)
h¿ = 111.111 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa
Others 0.00 kPa
LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN
WU 12.500 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 4.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 2: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 0.65 0.70 0.667

Ca,neg 0.077 0.074 0.0760
Cb,neg 0.014 0.017 0.0150

POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 0.65 0.70 0.667

Ca,pos,dl 0.032 0.03 0.0313
Cb,pos,dl 0.006 0.007 0.0063
Ca,pos,ll 0.053 0.049 0.0518
Cb,pos,ll 0.01 0.012 0.0106

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 15.200 kN-m Ms .000 kN-m
Mb,neg 6.750 kN-m Ml .000 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 4.627 kN-m Mb,pos,dl 2.096 kN-m
Ma,pos,ll 2.677 kN-m Mb,pos,ll 1.233 kN-m
Ma,pos,total 7.304 kN-m Mb,pos,total 3.329 kN-m

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 SUMMARY OF SLAB-23

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 23 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 15.2 7.304 0 6.75 3.329 .000 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.09839 0.52781 0.00000 0.48777 0.26565 0.00000
Req'd ρ 0.00411 0.00194 0.00000 0.00179 0.00097 0.00000
use ρ 0.00507 0.00507 NA 0.00507 0.00507 NA
As 628.680 628.680 NA 628.680 598.260 NA
Req'd s 180 180 NA 180 190 NA
use s 180 180 NA 180 190 NA

SLAB 24:

6.0 m

S24 6.0 m

MINIMUM THICKNESS OF SLAB:

perimeter of the panel
h¿
180
(6.0+6 .0)(2)
h¿ = 133.333 mm
180
instead use h = 150 mm
d e =¿ 124 mm

DEAD AND LIVE LOADS FROM NSCP 2001

DEAD LOADS
Floor finish 1.58 kPa
Ceiling 0.48 kPa
Partition load 1.00 kPa
Others 0.00 kPa

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 LIVE LOADS
Basic Floor Area 1.90 kPa
FACTORED LOADS
1.4WD 9.240 kN
1.7WL 3.230 kN
WU 12.500 kN

CLEAR SPAN
Long direction 6.00 m
Short direction 6.00 m

Typical floor 150 mm

Clear cover 20 mm
EFFECTIVE DEPTH
Long direction 124 mm
Short direction 124 mm
BAR DIAMETERS
Long direction 12 mm
Short direction 12 mm

DESIGN CONSTRAINTS:
fy 276.0 MPa
f'c 21.0 MPa
β 0.85
ρmax 0.028239465
ρmin 0.00507
γconcrete 23.6 kN/cu.m.

USING COEFFICIENT METHOD:

CASE 8: from table of coefficients for moments and shears in two-way slab
panels according to the ACI Code

NEGATIVE MOMENTS AT CONTINUOUS EDGE

m 1.00 1.00 1.000

Ca,neg 0.033 0.033 0.0330
Cb,neg 0.061 0.061 0.0610

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
 POSITIVE MOMENTS FOR LIVE LOAD AND DEAD LOAD

m 1.00 1.00 1.000

Ca,pos,dl 0.02 0.02 0.0200
Cb,pos,dl 0.023 0.023 0.0230
Ca,pos,ll 0.028 0.028 0.0280
Cb,pos,ll 0.03 0.03 0.0300

NEGATIVE MOMENTS

At continuous edge At discontinuous edge

Ma,neg 14.850 kN-m Ms 3.303 kN-m
Mb,neg 27.450 kN-m Ml 3.713 kN-m

POSITIVE MOMENTS

Along short direction Along long direction

Ma,pos,dl 6.653 kN-m Mb,pos,dl 7.651 kN-m
Ma,pos,ll 3.256 kN-m Mb,pos,ll 3.488 kN-m
Ma,pos,total 9.909 kN-m Mb,pos,total 11.139 kN-m

SUMMARY OF SLAB-24

SUMMARY
SHORT DIRECTION LONG DIRECTION
S - 24 Cont. Edge Midspan Discont. Edge Cont. Edge Midspan Discont. Edge
Moment 14.85 9.909 3.303 27.45 11.139 3.713 kN-m
h 150 150 150 150 150 150
d 124 124 124 124 118 124
Rn 1.07310 0.71605 0.23868 1.98361 0.88887 0.26831
Req'd ρ 0.00401 0.00265 0.00087 0.00764 0.00331 0.00098
use ρ 0.00507 0.00507 0.00507 0.00764 0.00507 0.00507
As 628.680 628.680 628.680 947.115 598.260 628.680
Req'd s 180 180 180 120 190 180
use s 180 180 180 120 190 180

Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa

Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph
Campuses: Hilltop | MH del Pilar | Pallocan East | Pallocan West | Lipa
Telephone Numbers: +63 43 723 1446 | 980 0041
Website: www.ub.edu.ph