Scribd
Upload
54 views

Book 2 Unit 11. Safe Anchoring - Planning and Operational Guidance For Cargo Ships Planning For Anchoring

The document provides guidance on planning and procedures for safely anchoring cargo ships. It outlines factors the master and chief officer should consider like suitable anchoring positions, depth of water, weather conditions, and amount of cable needed. Two standard methods for introducing anchors are described: walking the anchor out to half a shackle above the seabed then dropping it (for depths up to 50m), or stopping the vessel completely before walking the anchor out under power until it sets on the seabed (for depths over 50m). Very large crude carriers require special caution as their inertia means they must be nearly motionless both linearly and axially when anchoring in depths around 110m or less.

Uploaded by

Concepci�n Guti�rrez Araujo
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
54 views

Book 2 Unit 11. Safe Anchoring - Planning and Operational Guidance For Cargo Ships Planning For Anchoring

The document provides guidance on planning and procedures for safely anchoring cargo ships. It outlines factors the master and chief officer should consider like suitable anchoring positions, depth of water, weather conditions, and amount of cable needed. Two standard methods for introducing anchors are described: walking the anchor out to half a shackle above the seabed then dropping it (for depths up to 50m), or stopping the vessel completely before walking the anchor out under power until it sets on the seabed (for depths over 50m). Very large crude carriers require special caution as their inertia means they must be nearly motionless both linearly and axially when anchoring in depths around 110m or less.

Uploaded by

Concepci�n Guti�rrez Araujo
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Book 2

Unit 11. Safe anchoring - planning and operational guidance for cargo ships
Planning for Anchoring

The Master shall identify a suitable anchoring position before entering the anchorage area. He must conduct a
planned approach including speed reduction in ample time. Furthermore, he is responsible of deciding on which
method of anchoring to be used and the number of shackles necessary depending on the depth of water,
expected weather and holding ground. A simple rule in determining length of cable to use is:

Standard condition:
Length of cable = [(Depth of water in meters * 2) + 90 ] / 27.5

When good holding power cannot be expected (e.g. Strong Wind, Strong Current, Harder Sea bottom):
Length of cable = [(Depth of water in meters * 3) + 140 ] / 27.5

Preparation for Anchoring


The Chief Officer (or another experienced officer in lieu) must supervise letting go or weighing the anchors and
should only assign experienced crew members to anchor work.
Prior to Anchoring, the Chief Officer should be aware of:
a. Approximate anchoring position
b. Method of approach
c. Which anchor to use
d. Depth of water
e. Method of Anchoring
f. Final amount of Cables

Procedure of the Introduction to Anchoring

At the Forecastle:
Check brakes are on and clear the voyage securing devices (Anchor Lashings, Bow Compressed Bar etc.)
a. Start Hydraulic (Source of) Power of Windlasses
b. Check Anchor Shape / Light
c. Check Communication with the Bridge
d. Check Lighting on Forecastle including torch, at night time
e. Ensure all personnel are wearing Safety Helmets, Safety Shoes and Goggles.

Before Letting Go Anchor:


The Chief Officer shall confirm that there is no craft or any obstacle under the bow and inform to the Bridge. The
Master shall ensure that the vessel’s GPS speed at the time of anchoring is near-zero or indicates a slight
sternway. The speed should be verified by visual transits and/or Radar ranges of Landmarks, if available or other
fix conspicuous targets.
If the method of communication between Bridge and the Anchoring party is by Portable radio, the identification
of the ship should be clear to avoid misinterpretation of instructions from other users of such equipment in the
vicinity.
Routine Anchoring Operation
There are 2 methods for Anchoring according to depth of the water:

Method 1 (Preferable for Container Ships / Depths up to 50m)


a. Walk out the anchor to Half a shackle above the sea bottom
b. Hold the cable on the brake and take the windlass out of gear
c. Stop the vessel over ground
d. Drop the anchor
e. Control the speed of cable flow by the brake , while not allowing pile-up
f. Bring anchor cable direction forward and confirmed anchor holds its position.

Disadvantages:
If the brake fails, or there is too much speed over ground, the cable will run out to the bitter end with
consequent damage. The brake lining could also be damaged due to this Dynamic load (the Static load on brakes
to restrain movement of an anchored vessel is much less).

Method 2 (Suggested for Tankers / Depths over 50m)


a. Stop the vessel over ground
b. Walk out the anchor under power until the complete length of required cable is paid out and anchor holds its
position on the seabed.
c. Bring anchor cable direction forward and confirmed anchor holds its position.

Disadvantages:
Vessel must be completely stopped to avoid major damage to Windlass.

Particular Caution for VLCCs


VLCCs, because of their inertia, require great caution while anchoring. They can suffer equipment failure if
attempting to anchor whilst moving at speeds as low as half a knot over the ground. Hence, the vessel must be
nearly stopped not only in the linear direction but axial too, meaning the bow should not be swinging much
either while anchoring. The depth at which the vessel can safely anchor is about 110m or less, beyond which the
windlass may have extreme difficulty in recovering the anchor.

You might also like