Scribd
Upload
327 views1 page

Eposist HBS: Marine & Protective Coatings

This document provides information on EPOSIST HBS, a high-build surface tolerant anti-corrosive coating based on special epoxy resin. It can be applied to ship's hull, decks, water ballast tanks, holds and industrial structures. EPOSIST HBS has excellent resistance to moisture, weathering and mechanical load. It has been tested for non-contamination of grain cargo. Its recommended dry film thickness is 250 microns and it has a pot life of 5 hours at 20°C. EPOSIST HBS can be overcoated with other Wilko coatings and systems. Safety precautions and general application guidelines are also outlined.

Uploaded by

LHYT NTUA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
327 views1 page

Eposist HBS: Marine & Protective Coatings

This document provides information on EPOSIST HBS, a high-build surface tolerant anti-corrosive coating based on special epoxy resin. It can be applied to ship's hull, decks, water ballast tanks, holds and industrial structures. EPOSIST HBS has excellent resistance to moisture, weathering and mechanical load. It has been tested for non-contamination of grain cargo. Its recommended dry film thickness is 250 microns and it has a pot life of 5 hours at 20°C. EPOSIST HBS can be overcoated with other Wilko coatings and systems. Safety precautions and general application guidelines are also outlined.

Uploaded by

LHYT NTUA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

0615 E 05/11

Marine & Protective Coatings

EPOSIST HBS
Code No. / Colour Base ERP 1335 buff ERP 7101 grey
ERP 3900 red brown ERP 9106 silver

Hardener ERX 1755


Description High-build surface tolerant anti-corrosive coating based on special epoxy resin.
Excellent resistance to moisture, weathering and mechanical load.

Recommended use Can be applied even on simple hand tool cleaned surfaces for ship's hull, decks,
water ballast tanks, holds and industrial structures.

Certification Tested for non-contamination of grain cargo at the Newcastle Occupational Health
(NHS 7530/04), Great Britain.
Germanischer Lloyd GL-KORR 1139 HH
Product information
Solids volume abt. 82%
Recommended DFT/WFT 250/305 microns
Theoretical coverage 3,28 m²/litre (at stated solid volume and DFT./WFT.)
Specific gravity abt. 1,49 g/cm³

Mixture Base Hardener


by Volume 18 2
Flash point + 25°C
VOC < 250 g/litre DIN ISO 11890
Storage abt. 6 months (under normal conditions for un-mixed components)

Application
Pot life 5 hour(s) at 20°C
Method of application Preferable by airless spray, brush or roller also possible.
Tip size 0,019" - 0,023"
Thinner VEP 47 (for equipment cleaning)

Drying time Temperature + 5°C + 10°C + 20°C + 30°C


Touch dry 20 hrs. 12 hrs. 8 hrs. 6 hrs.
Overcoatability minimum 26 hrs. 18 hrs. 14 hrs. 12 hrs.
maximum 14 days at 20°C and 65 % relative humidity
Ready for use after 7 days at 20°C and 65% relative humidity

Surface preparation Remove grease, oil contamination with thinner or cleaning agents. Minimum
surface preparation St 2. Can be applied on old paint film with good adhesion.
Loose old paint flakes have to be removed properly.

Recommended paint system 1 - 2 x EPOSIST HBS Please consult our technical department
for repair and maintenance procedures.

Overcoatability Can be over-coated with same material and WILKOPOX, WILKOR, WILKONYL or
EPOSIST Systems for under water area. In case of over coating with WILKOTAN
BTD and WILKOR BTD top coats, please contact our technical department.
Generals
Safety precautions a) Follow all relevant local or national Health, Safety and Environmental regulations
of the legislator and trade association.
b) Prior use, read and follow strictly all notices on the material safety data sheet.

World-wide availability Minor product modifications may exist in order to comply with legislation or
particular local conditions.

General remarks During application the temperature of the surface should be at least 3°C above the
dew point of the air.

These technical data are given to you for information In Collaboration with: as these depend on factors beyond our control. In case of
purpose only. They are based on our own research and doubt, please consult our technical / service department.
experiences. No responsibility can be assumed due to Data are subject to change without prior notice and
different conditions during application, become void five years from the date issue.

You might also like