MICRO COMPONENT SYSTEM MCR-730

DRX-730/NX-E700 SERVICE MANUAL

The MCR-730 consists of the DRX-730 and the NX-E700.

IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known
and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury,
destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise
all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or
the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service
departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and
specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the
distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

■ CONTENTS
TO SERVICE PERSONNEL ........................................2–4 UPDATING FIRMWARE .......................................... 17–23
PREVENTION OF ELECTROSTATIC DISCHARGE ......5 SELF-DIAGNOSTIC FUNCTION ............................24–36
REGION MANAGEMENT INFORMATION .....................6 DISPLAY DATA .............................................................37
SYSTEM COMPOSITION ................................................6 IC DATA ...................................................................38–43
FRONT PANELS .............................................................7 BLOCK DIAGRAMS ................................................44–45
REAR PANELS ...........................................................8–9 PRINTED CIRCUIT BOARDS .................................46–51
REMOTE CONTROL PANELS .......................................9 PIN CONNECTION DIAGRAMS ...................................52
SPECIFICATIONS ................................................... 10–11 SCHEMATIC DIAGRAMS .......................................53–55
INTERNAL VIEW .......................................................... 12 REPLACEMENT PARTS LIST ................................57–69
DRX-730/NX-E700

SERVICE PRECAUTIONS ...................................... 13–14 REMOTE CONTROL ...............................................70–71

DISASSEMBLY PROCEDURES ............................. 15–16

Copyright © 2008 All rights reserved.

10111 9 This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
animate '08.11
 DRX-730/NX-E700

■ TO SERVICE PERSONNEL AC LEAKAGE

1. Critical Components Information WALL EQUIPMENT TESTER OR
Components having special characteristics are marked and OUTLET UNDER TEST EQUIVALENT
must be replaced with parts having specifications equal to those
originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated INSULATING
TABLE
from supply circuits.
• Meter impedance should be equivalent to 1500 ohms shunted • Leakage current must not exceed 0.5mA.
by 0.15 μF. • Be sure to test for leakage with the AC plug in both polari-
ties.

“CAUTION”
“F501: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V
FUSE.”
CAUTION
F501: REPLACE WITH SAME TYPE 4A, 125V FUSE.
ATTENTION
F501: UTILISER UN FUSIBLE DE RECHANGE DE MÉME TYPE DE 4A, 125V.

WARNING: CHEMICAL CONTENT NOTICE!

This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive
harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON
WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or
expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.

About lead free solder

All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder.
Among some types of lead free solder currently available, it is recommended to use one of the following types for the
repair work.
• Sn + Ag + Cu (tin + silver + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)

Caution:
As the melting point temperature of the lead free solder is about 30°C to 40°C (50°F to 70°F) higher than that of the lead
DRX-730/NX-E700

solder, be sure to use a soldering iron suitable to each solder.

2
 DRX-730/NX-E700

WARNING: Laser Safety

This product contains a laser beam component. This component may emit invisible, as well as visible radiation,
which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must
be used during servicing of the unit.
1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm/1 feet
away from the laser pick-up unit at all times. Do not stare at the laser beam at any time.
2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.
3) CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.

Laser Emitting conditions:

1) When the Top Cover is removed, and the STANDBY/ON SW is turned to the “ON” position, the laser component will
emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate
through the lens of the laser pick-up unit. Do not attempt any servicing during this period!
If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any
laser emissions.
2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory
prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this
manual. Adjustment of this control can increase the laser emission level from the device.

Laser Diode Properties

Type: Semiconductor laser AlGaInP Output Power: 5 mW (DVD)
Wave length: 655 nm (DVD) 7 mW (VCD/CD)
790 nm (VCD/CD) Beam divergence: 20 degree

DRX-730/NX-E700

3
 DRX-730/NX-E700

U, C models T, K, A, G, F, L, V models

Warning for power supply

The primary side of the power supply carries live mains voltage when the player is connected to the mains even
when the player is switched off !
This primary area is not shielded so it is possible to accidentally touch copper tracks and/or components when servicing
the player.
Service personnel have to take precautions to prevent touching this area or components in this area.
Note:
The screws on the DVD mechanism may never be touched, removed or re-adjusted.
Handle the DVD mechanism with care when the unit has to be exchanged!
The DVD mechanism is very sensitive for dropping or giving shocks.
DRX-730/NX-E700

4
 DRX-730/NX-E700

■ PREVENTION OF ELECTROSTATIC DISCHARGE

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are
called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect
transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence
of component damage caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD
on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging
ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protect-
ed)” can generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it.
(Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil
or comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective
material to the chassis or circuit assembly into which the device will be installed.
CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as
brushing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).

Grounding for electrostatic breakdown prevention

1. Human body grounding.
Use the antistatic wrist strap to discharge the static electricity from your body.
2. Work table grounding.
Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet.

Caution:
The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch
the optical pickup.

Anti-static wrist strap

1M-ohms
Conductive material
(sheet) or steel sheet

DRX-730/NX-E700

5
 DRX-730/NX-E700

■ REGION MANAGEMENT INFORMATION

Region Management Information: This DVD player is designed and manufactured to respond to the Region
Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does
not correspond to the Region number of this DVD player, this DVD player cannot play this disc.

This product incorporates copyright

protection technology that is protected
5
by method claims of certain U.S. patents
and other intellectual property rights 2

o w n e d b y M a c ro v i s i o n C o r p o r a t i o n
and other rights owners. Use of this
copyright protection technology must be 1
6 2
authorized by Macrovision Corporation,
2
and is intended for home and other 3

limited viewing uses only unless

4
otherwise authorized by Macrovision 4
5

Corporation. Reverse engineering or

2
disassembly is prohibited.

■ SYSTEM COMPOSITION
The MCR-730 consists of the DRX-730 and the NX-E700.

▼ NX-E700 ▼ NX-E700

▼ DRX-730

Color variations:
DRX-730/NX-E700

DRX-730 NX-E700
Gold color
Black color Black color
Silver color
White color White color

6
 DRX-730/NX-E700

■ FRONT PANELS
DRX-730 (U, C, T, K, A, G, F, L, V models)

Top view

NX-E700 (U, C, T, K, A, G, F, L, V models)

DRX-730/NX-E700

7
 DRX-730/NX-E700

■ REAR PANELS
DRX-730 (U, C models) DRX-730 (G model)

DRX-730 (T model) DRX-730 (F model)

DRX-730 (K model) DRX-730 (L model)

DRX-730 (A model) DRX-730 (V model)

DRX-730/NX-E700

8
 DRX-730/NX-E700

NX-E700

U, C, K, A, G, F, L, V models

T model

T model

■ REMOTE CONTROL PANELS

U, C, T, K, A, L, V models G, F models

DRX-730/NX-E700

9
 DRX-730/NX-E700

■ SPECIFICATIONS
DRX-730
■ Amplifier Section
Maximum Power (JEITA, 6 ohms, 1 kHz, 10 % THD) Pb Output/Component Video Output
SP OUT ........................................................... 30 W + 30 W ...............................................................0.7 Vp-p (75 ohms)
Minimum RMS Output Power (6 ohms, 1 kHz, 0.9 % THD) Pr Output/Component Video Output
SP OUT ........................................................... 20 W + 20 W ...............................................................0.7 Vp-p (75 ohms)
Input Sensitivity/Input Impedance (1 kHz, 20 W) RGB AV MONITOR OUT (SCART) Output [G, F models]
AUX, PORTABLE ..................................... 400 mV/47 k-ohms ...............................................................0.7 Vp-p (75 ohms)
Maximum Input Signal Level (1 kHz, 0.5 % THD)
■ Input/Output Section
AUX, PORTABLE ............................................. 2.2 V or more
Input Terminal
Output Level/Output Impedance (400 mV)
Analog audio ............................... AUX L/R (pin jack – rear)
REC OUT (1 kHz) .................................. 400 mV/1.2 k-ohms
PORTABLE (mini jack – front)
WOOFER PRE OUT (50 Hz) ........................ 2.0 V/1 k-ohms
Other ...........................................USB (USB 1.1, full speed)
HEADPHONE (1 kHz, 32 ohms) ............. 660 mV/100 ohms
DOCK
Frequency Response (AUX, PORTABLE, 10 to 22 kHz)
Output Terminal
SP OUT ..................................................................... 0/-3 dB
Analog audio ................................................ SPEAKERS L/R
Signal to Noise Ratio (AUX, PORTABLE, IHF-A) PHONES
SP OUT (Input shorted 400 mV) ..................95 dB or more AUX L/R (REC)
Total Harmonic Distortion SUBWOOFER
(AUX, PORTABLE, 20 kHz-LPF, 1 kHz, 1 W) Digital audio ........................................................... OPTICAL
SP OUT ..........................................................0.05 % or less Video .......................................................VIDEO (composite)
Tone Control Characteristics COMPONENT (Y, PB, PR)
BASS HDMI
SP OUT (100 Hz) ................................................... ±10 dB AV MONITOR OUT (SCART) (G, F models)
TREBLE
■ General
SP OUT (10 kHz) ................................................... ±10 dB
Power Supply
■ Tuner Section U, C models ..................................................... AC 120 V, 60 Hz
Tuning Range T model ............................................................ AC 220 V, 50 Hz
FM K model ............................................................ AC 220 V, 60 Hz
U, C models ......................................... 87.5 to 107.9 MHz A model ............................................................ AC 240 V, 50 Hz
T, K, A, G, F models ....................... 87.50 to 108.00 MHz G, F models ..................................................... AC 230 V, 50 Hz
L, V models ............. 87.5 to 108.0 / 87.50 to 108.00 MHz L model ................................................ AC 220-240 V, 50/60 Hz
V model ............................................................ AC 110 V, 60 Hz
AM
U, C models ........................................... 530 to 1,710 kHz Power Consumption
T, K, A, G, F models ............................. 531 to 1,611 kHz ...................................................................................... 30 W
L, V models .................... 530 to 1,710 / 531 to 1,611 kHz Standby Power Consumption (reference data)
.......................................................................Less than 1 W
■ DVD Section
Dimensions (W x H x D)
Output Level (DVD/VIDEO, CD/CD-DA) ........... 215 x 113 x 300 mm (8-7/16" x 4-7/16" x 11-13/16")
REC OUT (1 kHz, 0 dB) ........................................ 2 ±0.3 V
Weight
Signal to Noise Ratio (DVD/VIDEO, CD/CD-DA) ...............................................................2.9 kg (6 lbs. 6 oz.)
REC OUT (Weighted) ..................................100 dB or more
Finish
Dynamic Range Gold color .......................................................... T, A models
REC OUT Black color ...................................... U, A, G, F, L, V models
DVD, 48 kHz, 24 bit ...................................95 dB or more Silver color ................................. C, K, A, G, F, L, V models
CD-DA/VIDEO, CD ......................................95 dB or more White color ..........................................C, K, A, G, F models
Harmonic Distortion + Noise (DVD/VIDEO, CD/CD-DA) Accessories
DRX-730/NX-E700

REC OUT .....................................................0.005 % or less Remote control ................................................................ x 1

Frequency Response Battery (R6, AA, UM-3) ................................................... x 2
PRE OUT Indoor FM antenna (1.4 m) ............................................. x 1
CD-DA/VIDEO, CD ...................................10 Hz to 20 kHz AM loop antenna (1.2 m) ................................................ x 1
DVD, 48 kHz, sampling ...........................10 Hz to 22 kHz Video pin cable (1.5 m) .................................................. x 1
DVD, 96 kHz, sampling ...........................10 Hz to 44 kHz
* Specifications are subject to change without notice due to product
Video Output improvements.
Composite .................................................1 Vp-p (75 ohms)
Y Output/Component Video Output
..................................................................1 Vp-p (75 ohms)

10
 DRX-730/NX-E700

NX-E700
■ Speaker Section U .......................U.S.A. model G .................European model
C .................Canadian model F .................... Russian model
Type ................................. 2-way bass reflex speaker system
T .................... Chinese model L .................Singapore model
Magnetic shielding type K ..................... Korean model V ..................... Taiwan model
Driver A ................Australian model
Woofer ...........................................11 cm (4-1/2") cone type
Tweeter .............................................2.5 cm (1") dome type
Frequency Response
...................................................... 60 Hz to 28 kHz (-10dB)
Impedance ...................................................................6 ohms
Nominal Input ................................................................ 40 W
Maximum Input ............................................................ 110 W DivX, DivX Ultra Certified, and associated logos
are trademarks of DivX, Inc. and are used under
Sensitivity ..................................................... 85 dB/2.83 V/m
license.
Crossover Frequency ................................................... 3 kHz
Manufactured under license from Dolby Laboratories.
Input Terminal ......................................... Screw/Banana type Dolby and the double-D symbol are trademarks of Dolby
Dimensions (W x H x D) .......165 mm x 255 mm x 183 mm Laboratories.

(6-1/2" x 10-1/16" x 7-3/16") DTS and DTS 2.0 + Digital Out are registered trademarks
Weight ....................................................3.4 kg (7 lbs. 8 oz.) and the DTS logos and Symbol are trademarks of DTS,
Inc.
Finish
Black color ........................ U, C, T, K, A, G, F, L, V models “HDMI”, the “HDMI” logo, and “High-Definition Multimedia
Interface” are trademarks or registered trademarks of
White color ..........................................C, K, A, G, F models
HDMI Licensing LLC.
Accessory ...................................... Speaker cable (4 m) x 1
MPEG Layer-3 audio decoding technology licensed from Fraunhofer
* Specifications subject to change without prior notice. IIS and Thomson multimedia.
Windows Media is either a registered trademark or trademark of
Microsoft Corporation in the United States and/or other countries.

• DIMENSIONS

DRX-730

14 (9/16")

NX-E700
300 (11-13/16")
271 (10-11/16")
219 (8-5/8")

255 (10-1/16")

15 (9/16")
DRX-730/NX-E700
105 (4-1/8")

113 (4-7/16")

165 (6-1/2") 183 (7-3/16")

(5/16")

175 (6-7/8")
8

215 (8-7/16") Unit: mm (inch)

11
 DRX-730/NX-E700

■ INTERNAL VIEW
Top view

1 2 3 4

1 AM/FM TUNER
2 MAIN (2) P.C.B. (G, F models)
3 DVD MODULE P.C.B.
4 SUB (1) P.C.B.
5 MAIN (1) P.C.B.
6 SUB (2) P.C.B.
7 DVD MECHANISM ASS’Y

5 6 7
DRX-730/NX-E700

12
 DRX-730/NX-E700

■ SERVICE PRECAUTIONS
When DVD MODULE P.C.B. of this unit is replaced, the serial number and new ID number (device key) must be reported to
YCJ (Yamaha Corporation Japan) by email. (Fig. 1)

Email: [email protected]

[email protected] [email protected]
DRX-730 Model name
Y015018XZ Serial number of DRX-730
008000155 ID number (device key)

Send this email to YCJ

Fig. 1

● Check the Serial Number

The serial number “SER.NO.xxxxxxxx” can be found at the bottom of this unit. (Fig.2)

Bottom view

U, C, G, F, V models
Front side Rear side

T, K, A, L models

Serial number

Fig. 2

DRX-730/NX-E700

13
 DRX-730/NX-E700

● Check the New ID Number (Device key)

Connection
Connect the VIDEO OUT terminal of this unit to the VIDEO IN terminal of the TV monitor with a video pin cable.

Operation Procedure
Perform following steps while watching the TV monitor screen and using the keys of this unit.
1. While pressing those 2 keys of this unit as indicated in the figure below, press the “STANDBY/ON” key to turn on
the power.
The self-diagnostic function is activated. (Fig. 3)

“STANDBY/ON” key Turn on the power while pressing these keys.

Fig. 3

2. Press “ (Previous/Rewind)” key once to select main menu 11 DVD WRITE ID.
3. Press “ (Play/Pause)” key once to select sub-menu 11-2 DVD CLEAR ID.
Wait about 15 seconds.

Self-diagnostic function starting display Main menu 11 – DVD WRITE ID sub-menu 11-2 – DVD CLEAR ID
VER,A34 S:D2E1 DVD WRITE ID DVD CLEAR ID

Fig. 4

4. New ID number (device key) will appear on the TV monitor screen as shown below.
Note: While the ID number (device key) is displayed, never operate any keys of the remote control.

(Player's ID Number Setting)

ID Number ?
0 0 8 0 0 0 1 5 5 New ID number (device key)
Compare * The displayed “008000155” is an
* * * * * * * * *
example.
<CLEAR> Exit

Input ID Number !
DRX-730/NX-E700

Fig. 5

5. To exit the self-diagnostic function, press “STANDBY/ON” key to turn off the power.

14
 DRX-730/NX-E700

■ DISASSEMBLY PROCEDURES
(Remove parts in the order as numbered.) 3. Removal of DVD Mechanism Ass’y and DVD
Disconnect the power cable from the AC outlet. Module P.C.B.
1. Removal of Top Cover a. Remove 4 screws ( ) and screw ( ). (Fig. 1)
b. Remove 3 screws ( ) and screw ( ). (Fig. 1)
a. Remove 2 screws ( ) and 4 screws ( ). (Fig. 1)
c. Remove CN962, CN967 and CN968. (Fig. 1)
b. Slide the top cover rearward to remove it. (Fig. 1)
d. Remove the DVD mechanism ass’y and DVD module
2. Removal of Front Panel Unit P.C.B. together with support P.C.B.. (Fig. 1)
e. Remove CN964 and CN965. (Fig. 1)
a. Open the disc tray, remove the lid and close the disc
f. Remove CN966, and ground the terminal face of the
tray. (Fig. 3)
flexible flat cable with a clip or the like. (Fig. 1)
b. Remove 2 screws ( ), 2 push rivets and then remove 2
g. Remove the DVD mechanism ass’y. (Fig. 1)
side panels. (Fig. 1)
c. Remove 3 screws ( ). (Fig. 1)
d. Release 2 hooks, pull out the front panel unit forward. 13 mm
(1/2")
(Fig. 1) DVD module P.C.B.
e. Remove CB12 and CB26. (Fig. 1) Terminal side

Clip CB965

Use a clip or other item

to ground the unit.

Support P.C.B.

CB966

CB964

DVD mechanism ass'y

Top cover

DVD module P.C.B.

CB968

CB962

P.C.B. CB967
support

DVD mechanism ass'y

Push rivet
Front panel unit

Hook
DRX-730/NX-E700

CB12

CB26
Side panel
MAIN (1) P.C.B. Hook
Push rivet

Lid
Side panel

Fig. 1
15
 DRX-730/NX-E700

● How to manually eject the disc tray

a. Move the slider in the direction indicated in the figure below with a screwdriver until the disc tray is ejected. (Fig. 2)
Note: An Allen hex socket screwdriver 2.5 mm is recommended for this operation.
b. Gently pull the disc tray out.

Screwdriver
(An Allen hex socket screwdriver 2.5 mm)

Disc tray
Lid

Fig. 2

When checking the P.C.B.s:

• Spread the rubber sheet and the cloth. Then place this unit on the cloth and check it. (Fig. 3)
• Reconnect all cables (connectors) that have been disconnected.
• When connecting the flexible flat cable, be careful with polarity.
• Connect the ground point of the DVD module P.C.B., AM/FM tuner and P.C.B. support to the chassis with a ground
lead or the like. (Fig. 3)

Ground lead
CB967 AM/FM tuner
CB962 Ground lead
DVD module P.C.B.
CB968
P.C.B. support
DVD mechanism ass'y

CB7
CB4
CB9
CB11

Ground lead
DRX-730/NX-E700

MAIN (1) P.C.B.

Rubber sheet and cloth

Fig. 3

16
 DRX-730/NX-E700

■ UPDATING FIRMWARE
Writing to the microprocessor

After replacing the following parts update the latest firmware according to the following procedure.
MAIN P.C.B.
Microprocessor (IC11) of MAIN P.C.B.

● Required tools ● Preparation and precautions before starting

• Program downloader program the operation
........................................................ FlashSta.exe • Download firmware downloader program and
• Firmware firmware from the specified source to the same
................................................... DRX730_vx.mot folder of the PC.
...................................................... DRX730_vx.id • Prepare the above specified RS232C cross cable.
• RS232C cross cable “D-sub 9 pin female” • While writing, keep the other application software
(Specifications) on the PC closed.
It is also recommended to keep the software on
Pin No.2 RxD Pin No.2 RxD
the task tray closed as well.
Pin No.3 TxD Pin No.3 TxD
Pin No.5 GND Pin No.5 GND
Pin No.7 RTS Pin No.7 RTS
Pin No.8 CTS Pin No.8 CTS

• RS232C conversion jig (Part No.: AAX77610)

● Confirmation of Firmware Version and Checksum

Before and after writing to the microprocessor, check the firmware version and checksum with the self-diagnostic
function menu.

Using the self-diagnostic function menu, check that the firmware is updated successfully.
Start up the self-diagnostic function of this unit and the “1. VERSION/SUM” is displayed.
For more information, see “SELF-DIAGNOSTIC FUNCTION”.

1. VERSION/SUM
Firmware version and checksum value of microprocessor
VER.B39 S:084C
The firmware version and checksum value of microprocessor (IC11 MAIN P.C.B.) is displayed.

DRX-730/NX-E700

17
 DRX-730/NX-E700

● Connection
1. Set the switch (SW301) of RS232C conversion adapter to the “FLASH UCOM” side.
2. Connect the writing port of this unit to the serial port (RS232C) of the PC with RS232C cross cable, RS232C con-
version jig and flexible flat cable as shown below. (Fig. 1)

Rear side Front side

"STANDBY/ON" key
Flexible flat cable 8P
Writing port
SW301 OTHER

FLASH
UCOM

RS232C conversion jig

RS232C cross cable

Fig. 1

● Operation Procedures
1. Connect the power cable of this unit to the AC outlet.
2. Start up FlashSta.exe, the screen will appear as shown below. (Fig. 2)
3. Select the port and data to be transmitted. (Fig. 2)
• Select Program
Select Internal flash memory
• RS232C Select Internal flash memory
Select the port of RS-232C
DRX-730/NX-E700

* For selection of the port, COM1 to 4 can be

used.
As COM5 or higher port cannot be used, se- Select the port of RS-232C
lect out of COM 1 to 4 of the setting on the PC
side.

Fig. 2

18
 DRX-730/NX-E700

4. Click [Refer...]. And select the firmware name. (Fig. 3)

* The ID code and MCU type are loaded automatically when the file is selected. (Fig. 3)
Click [OK]. (Fig. 3)

Click to open the window

Fig. 3

5. Click [E.P.R.], the screen appears as shown below. (Fig. 4)

Click [OK] to start writing. (Fig. 4)

Writing being executed.

DRX-730/NX-E700

Fig. 4

19
 DRX-730/NX-E700

6. When the program transmission is completed, the screen appears as shown below. (Fig. 5)
Click [OK] to end the procedure. (Fig. 5)

Fig. 5

7. Using the self-diagnostic function menu, check that the firmware is updated successfully.
* When the displayed firmware version and checksum are different from written ones, perform the “Writing to the
microprocessor” procedure all over again.
8. End “FlashSta.exe”.
9. Disconnect the power cable of this unit from the AC outlet.
10. Disconnect the RS232C cross cable, RS232C conversion jig and flexible flat cable.
DRX-730/NX-E700

20
 DRX-730/NX-E700

Writing to the Module Board

After replacing the Module board with the replacement part, be sure to write the latest firmware.

● Required Tools
Firmware CD
* To make the firmware CD, download the latest firmware from the specified download source to PC.
When making a firmware CD, set the CD volume label to “PIONEER”.
Firmware: S8CAxxxx.BIN

● Confirmation of Firmware Version

Before and after the writing firmware to the module board, follow the procedures below to check the firmware version.
1. Connect the VIDEO OUT terminal of this unit to the VIDEO IN terminal of the TV monitor with a video pin cable.
2. Connect the power cable of this unit to the AC outlet.
3. Press the “STANDBY/ON” key of this unit to turn on the power. (Fig. 6)
4. Press the “DVD/USB” key on the remote control to select the input DVD. (Fig. 6)
5. Press the “SETUP” key on the remote control. (Fig. 6)
The SETUP menu is displayed on the TV monitor. (Fig. 6)
6. Move the cursor to [Initial Settings] by pressing the “DOWN” key on the remote control and press the “ENTER” key.
(Fig. 6)

This unit Remote control

"STANDBY/ON" key

Audio Settings Video Adjust "SETUP" key " " (down) key

Play Mode Disc Navigator

"ENTER" key
Initial Settings

"DVD/USB" key
Make advanced settings "Initial Settings" select

Move Select ENTER Exit SETUP

Fig. 6 DRX-730/NX-E700

21
 DRX-730/NX-E700

7. Move the cursor to [Options] by pressing the “DOWN” key on the remote control repeatedly and press the “ON
SCREEN” key. (Fig. 7)
The ROM version is displayed. (Fig. 7)

This unit Remote control

"ON SCREEN" key
"STANDBY/ON" key

Initial Settings

Digital Audio Out Parental Lock Off(us)

Video Output DTS Downmix STEREO
Language DivX(R) VOD
Display
"SETUP" key
Options "Options" select

" " (down) key

REGION : 1
ROM VERSION : x.xx ROM version is displayed

Move Select ENTER Exit SETUP

Fig. 7

8. Press the “SETUP” key on the remote control to end the SETUP procedure. (Fig. 7)
9. Press the “STANDBY/ON” key of this unit to turn off the power. (Fig. 7)
DRX-730/NX-E700

22
 DRX-730/NX-E700

● Operation Procedures
CAUTION: Do not turn off the power while updating the firmware.
1. Connect the VIDEO OUT terminal of this unit to the VIDEO IN terminal of the TV monitor with a video pin cable.
2. Connect the power cable of this unit to the AC outlet.
3. Press the “STANDBY/ON” key of this unit to turn on the power. (Fig. 8)
4. Press the “OPEN/CLOSE” key of this unit to open the disc tray. (Fig. 8)
5. Put the firmware CD on the disc tray and close the disc tray.

"OPEN/CLOSE" key Disc tray

"PLAY/PAUSE" key

"STANDBY/ON" key

Fig. 8

6. “Upgrade?” is displayed on the TV screen. (Fig. 9)

Upgrade File DETECTED
7. Press the “PLAY/PAUSE” key of this unit, and then
writing of the firmware is started. (Fig. 8)
Upgrade ?
Press Play To Start

Fig. 9

8. After a few seconds, the disc tray opens automatically.

Remove the firmware CD and close the disc tray.
* At this time, do not turn off the power as writing of the firmware is going on in this unit.
* Writing takes about 1 minute.

Writing is being executed.

Upgrade File DETECTED Upgrade File DETECTED

Upgrade ? Upgrade ?
Press Play To Start Press Play To Start

File Copying UPGRADING

DRX-730/NX-E700

Fig. 10

9. When writing is completed, the display on the TV monitor disappears.

Press the “STANDBY/ON” key of this unit to turn off the power.
10. Check that the firmware version. (See “Confirm of Firmware Version”)
* When the displayed firmware version and checksum are different from written ones, perform the “Writing to the
microprocessor” procedure all over again.

23
 DRX-730/NX-E700

■ SELF-DIAGNOSTIC FUNCTION
This unit has self-diagnostic function that are intended for inspection, measurement and location of faulty point.
There are 11 main menu items, each of which has sub-menu items.
Listed in the table below are menu items and sub-menu items.

MAIN MENU SUB MENU

1 VERSION/SUM 1 VERSION/CHECK SUM DISPLAY
2 DESTINATION
3 CPU TYPE
4 REVISION NO
5 EEPROM CHECK
2 FACTORY PRESET 1 PRESET INH
2 PRESET RSRV
3 VOLUME CHECK 1 MIN
2 -20dB
3 MAX
4 BASS/TREBLE +10dB
5 BASS/TREBLE -10dB
4 DISPLAY CHECK 1 MENU display
2 VFD DISP OFF
3 VFD DISP ALL
4 VFD DIMMER
5 CHECK PATTERN
5 DOCK CHECK 1 Loop Back Check
2 Bluetooth Adapter Version
6 MUTE CHECK 1 OFF
2 HP MUTE
3 SW MUTE
7 D-AMP OSC MODE 1 INTERNAL
2 EXTERNAL 300kHz
3 EXTERNAL 350kHz
8 AD DATA CHECK 1 PS1/PS2
2 PS3/DC
3 DVD/DOCK
4 DEST
5 PANEL KEY
9 PROTECTION HISTORY 1 History 1
2 History 2
3 History 3
4 History 4
5 History 5
6 CLEAR HISTORY
10 POWER OFF FACTOR HISTORY 1 Power OFF factor history 1
2 Power OFF factor history 2
3 Power OFF factor history 3
4 Power OFF factor history 4
5 Power OFF factor history 5
6 CLEAR HISTORY
11 DVD SETTING 1 WRITE ID (DVD ID writing)
2 CLEAR ID (DVD ID Erasing)
DRX-730/NX-E700

3 REWRITE F/W (DVD F/W Rewriting)

24
 DRX-730/NX-E700

● Starting Self-Diagnostic Function

While pressing those 2 keys of this unit as indicated in the figure below, press the “STANDBY/ON” key to turn on the power.
The self-diagnostic function mode is activated.

Keys of this unit

Turn on the power while pressing these keys.

● Starting Self-Diagnostic Function in the protection cancel mode

If the protection function works and causes hindrance to trouble shoot, cancel the protection function as described below,
and it will be possible to enter the self-diagnostic function mode. (The protection functions other than the excess current
detect function will be disabled.)
While pressing those 2 keys of this unit as indicated in the figure above, press the “STANDBY/ON” key to turn on the power
and keep pressing those 2 keys for 3 seconds or longer.
The self-diagnostic function mode is activated with the protection functions disabled.
In this mode, the “SLEEP” segment of the FL display of this unit flashes to indicate that the mode is self-diagnostic function
mode with the protection functions disabled.

CAUTION!
Using this product with the protection function disabled may cause further damage to itself. Use special care when using
this mode.

● Canceling Self-Diagnostic Function

Before canceling self-diagnostic function, execute setting for FACTORY PRESET of main menu No. 2 (Memory initial-
ization inhibited or Memory initialized).
* In order to keep the user memory stored, be sure to select PRESET INHIBIT (Memory initialization inhibited).
Press the “STANDBY/ON” key to turn off the power.
DRX-730/NX-E700

25
 DRX-730/NX-E700

● Display provided when Self-Diagnostic Function started

The FL display of this unit displays the protection function history data then the main menu (sub-menu VERSION/CHECK
SUM of main menu No. 1 FIRMWARE VERSION) a few seconds later.

When there is no history of protection function:

Opening message Main menu display

When there is no protection history

After a few seconds

NO PROTECT A VER.B39 S:084C

Version (1 alphabet)

When there is a history of protection function:

The FL display appears as shown below depending on the type of the protection
function.

The protection function worked due to a defect or overload in the power supply. P1 PRT:000 A
If the power is turned on with the abnormality unsolved, the protection function
works in about 3 seconds to turn off the power.
P3 PRT:000 A

For detection of each protection function, refer to main menu No.8 AD DATA.

● History of protection function

When the protection function has worked, its history is stored in memory with a backup. Even if no abnormality is noted
while servicing the unit, an abnormality which has occurred previously can be defined as long as the backup data has
been stored.
The history of the protection function is cleared when self-diagnostic function is cancelled by selecting PRESET
RESERVED (Memory initialized) of main menu No. 2 or when the backup data is erased.
DRX-730/NX-E700

26
 DRX-730/NX-E700

● Operation procedure of Main menu and Sub-menu

There are 11 menu items, each of having sub-menu items.

Main menu selection

Select the menu using “ ” (Forward) and “ ” (Reverse) keys of this unit.
Sub-menu selection
Select the sub-menu using“ ” (Forward) and “ ” (Reverse) keys of this unit.

Keys of this unit

Sub-menu select

Reverse Forward

Main menu select

Reverse Forward

● Functions in Self-Diagnostic Function mode

In addition to the self-diagnostic function menu items, functions listed below are available.
• Input selection
• Muting
• Power on/off
* Functions related to the tuner and the set menu are not available.
DRX-730/NX-E700

● Initial setting used to start Self-Diagnostic Function

The following initial setting is used when starting self-diagnostic function.
When self-diagnostic function is canceled, this setting is restored to that before starting self-diagnostic function.
• Input: AUX

27
 DRX-730/NX-E700

● Details of Self-Diagnostic Function menu

1. FIRMWARE VERSION
The firmware version, checksum, destination, CPU type etc. are displayed.
The checksum is obtained by adding the data at every 8 bits (1 byte) for each program area and expressing the result as a
4-figure hexadecimal data.
* Numeric values in the figure example are for reference.

Firmware version and checksum value of microprocessor

VER.A34 S:D2E1
The firmware version and checksum value of microprocessor (IC11 MAIN P.C.B.) is
displayed.
DESTINATION
DEST:UC
The destination (UC / GF / LV / KA / T) is displayed.

CPU TYPE
CPU TYPE:64
The microprocessor type is displayed.

REVISION NO.
REVISION: 131
The revision no. of SVN is displayed.

EEPROM CHECK
EEP:NO DEVICE
Frequency of writing into EEPROM is displayed.

2. FACTORY PRESET
This menu is used to reserve/inhibit initialization of the backup IC.

PRESET INHIBIT (Initialization inhibited)

2.PRESET INH
RAM initialization is not executed. Select this sub-menu to protect the values set by the
user.
Note: The protection history will not be erased using PRESET INHIBIT.
PRESET RESERVED (Initialization reserved)
2.PRESET RSRV
Initialization of the back-up IC is reserved. (Actually, initialization is executed the next
time that the power is turned on.) Select this sub-menu to reset to the original factory
settings or to reset the IC. Use PRESET RESERVED to erase the protection history.

CAUTION: Before setting to the PRESET RESERVED, write down the existing preset memory content of the Tuner in a table
as shown below. (This is because setting to the PRESET RESERVED will cause the user memory content to be
erased.)

Preset group P1 P2 P3 P4 P5 P6 P7 P8
A
B
DRX-730/NX-E700

C
D
E

28
 DRX-730/NX-E700

3. VOLUME CHECK
This menu is used to check the volume level setting.

VOLUME MIN.
3.VOLUME MIN

VOLUME -20dB
3.VOLUME -20dB

VOLUME MAX.
3.VOLUME MAX

BASS/TREBLE +10dB
3.BASS/TRBL +10

BASS/TREBLE -10dB
3.BASS/TRBL -10

DRX-730/NX-E700

29
 DRX-730/NX-E700

4. DISPLAY CHECK
This menu is used to check the FL display section.
The display condition varies as shown below according to the sub-menu operation.

Checking FL display section

Initial display

Initial display

All segments OFF

All segments OFF

All segments ON (dimmer 100%)

All segments ON (dimmer 100%)

All segments ON (dimmer 50%)

All segments ON (dimmer 50%)

Lighting of segments in lattice

Lighting of segments in lattice

Lighting in lattice

Short Normal

Segment conditions of the FL driver and the FL tube are checked by turning ON and OFF all segments. Next, the operation
of the FL driver is checked by using the dimmer control.
Then a short between segments next to each other is checked by turning ON and OFF all segments alternately (in lattice). (In
the above example, the segments in the second row from the top are shorted.)
DRX-730/NX-E700

30
 DRX-730/NX-E700

5. DOCK CHECK
This menu is used to check the DOCK connector without the iPod itself.

DOCK loop back check

After turning off the power, short between pins No. 14 (TX) and No. 18 (RX), between pins No. 1 (PWR) and No. 17 (ACCPOW)
and between pins No. 4 (iPDET) and No. 8 (DGND).
(Make sure that the power is turned off when shorting pins.)
Start the self-diagnostic function and select the menu.
The check result is displayed according to the following display specifications.

Note) Be sure to return the shorted pins to their original condition after executing this test.

15 16 17 18

9 10 11 12 13 14
5.DOCK:NG NNNN
3 4 5 6 7 8 OK = all Y
NG = others
10 k-ohms
1/4 W

1 19 20 21 2

DOCK connector

Check item Short pins Result Display

Pins No.14 (TX) OK Y ⎫
UART loop back test ⎬
– No.18 (RX) NG N ⎭
iPAP (iPod accessory power) Pins No.1 (PWR+) High Y ⎫
IC11 pin No. 38 ⎬
detection – No.17 (ACCPWR) Low N ⎭
iPDET (iPod installation to Pins No.4 (iPDET) Low Y ⎫
IC11 pin No. 40 ⎬
DOCK) detection – No.8 (DGND) High N ⎭
Pins No.21 (DKID) 10 k-ohms, 1/4 W ⎫
Y
– No.8 (DGND) pull down ⎪
DKID (DOCK ID) detection IC11 pin No. 90 ⎬
* 10 k-ohms, 1/4 W ⎪
Other N ⎭
pull down

Bluetooth adapter version

The firmware version of the YBA-10 (YAMAHA) connected to the DOCK is displayed.

5.BT V:--------
DRX-730/NX-E700

31
 DRX-730/NX-E700

6. MUTE CHECK
This menu is used to select the MUTE status of HP (phones) / SW.

MUTE
6.MUTE OFF
The MUTE function of HP (phones) and SW (subwoofer) is turned OFF.

HP MUTE
6.HP MUTE ON
The MUTE function of HP (phones) is turned ON.

SW MUTE
6.SW MUTE ON
The MUTE function of SW (subwoofer) is turned ON.

7. D-AMP OSC MODE

This menu is used to select the operation setting of digital amplifier.

INTERNAL
7.D-AMP OSC INT

EXTERNAL 300 kHz

7.OSC EXT 300k

EXTERNAL 350 kHz

7.OSC EXT 350k
DRX-730/NX-E700

32
 DRX-730/NX-E700

8. AD DATA CHECK
This menu is used to display the A/D conversion value of the microprocessor which detects panel keys of this unit and
protection functions in using the sub-menu.
When KEY menu is selected, keys become non-operable due to detection of the values of all keys. However, it is
possible to advance to the next sub-menu by turning the INPUT of this unit.
* Numeric values in the figure example are for reference.

P1/P2 (Power supply voltage protection detection)

Power supply voltage protection value 8.P1:288 P2:349
(Normal value: P1: 190 to 380, P2: 260 to 450)
P1: Detects +12FL, -20D and +3.3.
P2: Detects Vp, +20D, +5FL and +10T.
* If Px is out of the normal value range, the protection function works to turn
off the power.
(Reference voltage: 5V=500)

P3/DC (Power supply voltage protection detection/

Power amplifier DC protection detection) 8.P3:198 DC:260
P3: Amp DC protection
Detects 6R3V, V+5V and 3R3.
(Normal value: 160 to 240 (select input DVD), 0 to 30 (select input other))
* If Px is out of the normal value range, the protection function works to
turn off the power.
(Reference voltage: 5V=500)
DC: Power amplifier DC (DC voltage) output is detected.
(Normal value: 180 to 320)
(Reference voltage: 5V=500)

DV/DK (DVD/DOCK)
DV: DVD power supply detection. 8.DV:331 DK:500
(Normal value: 240 or more)
DK: DOCK type detection
(Reference voltage: 5V=255)

DESTINATION
The destination of this unit is displayed. 8.DEST:000
DRX-730/NX-E700

Destination for AD port (pin no. 97 of IC11) pull-up resistance 10k-ohms.

Destination for AD port

Pull-up resistance 10 k-ohms
ohm 0 + 2.7 k + 6.8 k + 15.0 k + 47.0 k
V 0 - 0.5 0.5 - 1.6 1.6 - 2.5 2.5 - 3.6 3.6 - 5.0
Value 0 - 50 50 - 160 160 - 250 250 - 360 360 - 500
pin 97 (DEST) U, C G, F L, V K, A T

33
 DRX-730/NX-E700

KEY (K0)
When the A/D value of the panel key becomes out of the specified range, 8.KEY:500
normal operation will not be available. Check each panel key for the constant
of the voltage dividing resistance, soldered condition, etc, referring to the
table below.
(Reference voltage: 5 V = 500)

Key input for AD port

Pull-up resistance 10 k-ohms
ohm 0 + 1.2 k + 1.2 k + 7.9 k + 12.7 k + 20.7 k ∞
V 0 - 0.2 0.3 - 0.7 0.8 - 1.7 1.8 - 2.7 2.8 - 3.2 3.3 - 4.2 4.7 - 5.0
Value 0 - 20 30 - 70 80 - 170 180 - 270 280 - 320 330 - 420 470 - 500
(SEARCH/SKIP -
pin 89
OPEN/CLOSE PLAY/PAUSE STOP and SEARCH/SKIP - SEARCH/SKIP + KEY OFF
(KEY0)
SEARCH/SKIP +)

9. PROTECTION HISTORY
The 5 protection histories are displayed.

Example
Protection history 1
9-1 P2 xxxx

Example
Protection history 2
9-2 P3 xxxx

Example
Protection history 3
9-3 DC xxxx

Example
Protection history 4
9-4 NO PRT

Example
Protection history 5
9-5 NO PRT

Protection history clear

9-6 CLEAR HIST
Press the “OPEN/CLOSE” key, and the protection history will be initialized.
DRX-730/NX-E700

34
 DRX-730/NX-E700

10. POWER OFF FACTOR HISTORY

The 5 power OFF factor histories are displayed.

Power OFF factor history 1

10-1 NO HISTORY

Power OFF factor history 2

10-2 NO HISTORY

Power OFF factor history 3

10-3 NO HISTORY

Power OFF factor history 4

10-4 NO HISTORY

Power OFF factor history 5

10-5 NO HISTORY

Power OFF factor history clear

10-6 CLEAR HIST
Press the “OPEN/CLOSE” key, and the power OFF factor history will be initialized.

Power OFF factor display are as follows.

Display Factor

Microprocessor reset
10-x CPU RESET

Power down
10-x POWER DOWN

Protection
10-x PROTECTION

Timer off
10-x TIMER OFF

“STANDBY/ON” key of this unit

10-x PANEL KEY

“STANDBY/ON” key of remote control

10-x REMOCON

Auto standby
10-x AUTO STBY

Not history
DRX-730/NX-E700

10-x NO HISTORY

35
 DRX-730/NX-E700

11. DVD SETTING

This mode is prepared mainly for manufacturing use.

DVD WRITE ID ID Write Ent01

DVD CLEAR ID

DVD REWRITE F/W

Select “DVD CLEAR ID” to check the ID number (device key) of the module board.
See “Check the New ID number” for details.
DRX-730/NX-E700

36
 DRX-730/NX-E700

■ DISPLAY DATA
● V801 : 16-BT-133GNK (SUB P.C.B.)
61 1

PATTERN AREA

● PIN CONNECTION

Pin No. 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Connection P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31 P32 P33 P34 P35 NC 16G 15G 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G NP NP NX F1

Pin No. 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
Connection F2 NX NP NP P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16
Note : 1) F1, F2 ..... Filament 2) NP ..... No pin 3) NX ..... No extended Pin 4) 1G − 16G ..... Grid 5) NC ..... No connection

● GRID ASSIGNMENT
16G

1G 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G 15G

1-1 2-1 3-1 4-1 5-1

1-2 2-2 3-2 4-2 5-2

1-3 2-3 3-3 4-3 5-3

1-4 2-4 3-4 4-4 5-4

1-5 2-5 3-5 4-5 5-5

1-6 2-6 3-6 4-6 5-6

1-7 2-7 3-7 4-7 5-7

(1G – 15G)

● ANODE CONNECTION

1G – 15G 16G 1G – 15G 16G 1G – 15G 16G

P1 1-1 P13 3-3 P25 5-5
P2 2-1 P14 4-3 P26 1-6
P3 3-1 P15 5-3 P27 2-6 –
P4 4-1 P16 1-4 P28 3-6 –
P5 5-1 P17 2-4 P29 4-6 –
P6 1-2 P18 3-4 5-6
DRX-730/NX-E700

P30 –
P7 2-2 P19 4-4 P31 1-7 –
P8 3-2 P20 5-4 P32 2-7 –
P9 4-2 P21 1-5 P33 3-7 –
P10 5-2 P22 2-5 P34 4-7 –
P11 1-3 P23 3-5 P35 5-7 –
P12 2-3 P24 4-5

37
 DRX-730/NX-E700

■ IC DATA
IC11: R5F3640DNFA (MAIN P.C.B.)
Single-chip 16-bit Microprocessor

8 8 8 8 8 8

Port P0 Port P1 Port P2 Port P3 Port P4 Port P5

VCC2 ports

Internal peripheral functions

UART or clock synchronous Clock generation circuit
serial I/O X IN-XOUT
Timer (16-bit)
(6-channels) XCIN-XCOUT
Outputs (timer A): 5 PLL frequency synthesizer
Clock synchronous On-chip oscillator (125 kHz)
Inputs (timer B): 6 serial I/O
(8 bits x 2 channels) DMAC
Three-phase motor control circuit (4 channels)

CRC arithmetic circuit (CCITT)

Watchdog timer (Polynomial : X 16+X12+X5+1)
(15-bits)
M16C/60 series Memory
A/D converter Microprocessor core
(10-bits X 26-channels) ROM
SB
D/A converter R0H R0L
R1H R1L USP RAM
(8-bits X 2-channels) R2 ISP
R3
INTB
A0 PC
A1
A1
FB FLG Multiplier
FB

VCC1 ports

Port P10 Port P9 Port P8 Port P7 Port P6

8 8 8 8 8
DVDMUTE_E
DA_LATCH
RDS_RDY

DA_ZFLG
RDS_RST

USB_PRT
KEY_DET

STEREO

USB_EN
DVD_PS

TUNED
TMUTE
HPDET

/SWMT
/HPMT
FL_CE
GSCK
RDDA

TUDO
GSDT
RDCL

TUCK
VCC2
TUCE
STBY

TUDI
REM

PRY

VSS
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51

/ICFL 81 50 DOCK_POWER
LED_H 82 49
LED_P 83 48
LED_T 84 47
IREB 85 46 CE
IREA 86 45 SDA_VOL
VREB 87 44 SCL_VOL
VREA 88 43 VMUTE
KEY0 89 42
DOCK_VER 90 41 EPM
DVD_VDET 91 40 iPod_DET
DC_PRT 92 39 TEST
PSPRT3 93 38 iPod_PDET
PSPRT2 94 37 DVD_SCLK
PSPRT1 MDATA
DRX-730/NX-E700

95 36
AVSS 96 35 SDATA
DEST 97 34 BUSY
VREF 98 33 SCLK
AVCC 99 32 RXD
100 31 TXD
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
2
3
4
5
6
7
8
9
XREADY
XDVDRST
DVDPOWER
iPod_PRT

BYTE
CNVSS
XCIN
XCOUT
RESET
XOUT
VSS
XIN
VCC1
NMI
DVD_ACK
PDET
AMP_PRT
AMP_MODE
AMP_CLK
AMP_MT
AMP_CKSEL
SCL_EEP
FILAMENT
INH_RECA
DSDA_EEP
iPod_RX
iPod_TX

38
 DRX-730/NX-E700

No. Function Name Port Name I/O Detail of Function

1 P96 I/O Pulldown
2 P95 I/O Pulldown
3 XREADY P94 O DVD module I/F ready signal output
4 XDVDRST P93 O DVD module I/F reset output
DVD module HDMI power supply ON/OFF output
5 DVDPOWER P92 O
(H: power on, L: power off)
PS protection detection for iPod power source
6 iPod_PRT P91 I
(H: when normal, L: when abnormal)
7 P90 I Pulldown
8 BYTE – When in single chip mode: VSS (GND)
Processor mode selection
Lo: single chip mode, Hi: to flash built-in boot mode * Pulldown
9 CNVSS –
When resetting hardware: required
to boot mode with P50=H, P55=L, CNVss=H settings
10 XCIN P87 – Clock oscillation input for clock
11 XCOUT P86 – Clock oscillation output for clock
12 RESET – RESET [L: RESET]
13 XOUT – 16MHz OUT
14 VSS – GND
15 XIN – 16MHz IN
16 VCC1 – Power supply +5V
17 NMI P85 I Connect to Vcc via resistor
18 DVD_ACK P84 INT-IN DVD module I/F ACK interrupt (H: communication started)
19 PDET P83 INT-IN Power shutoff detection interrupt (L: shutoff)
D-AMP protection detection (OCP)
20 AMP_PRT P82 INT-IN
(H: when abnormal, L: when normal)
21 AMP_MODE P81 O D-AMP reset (H: when usual, L: when resetting)
TMR-
22 AMP_CLK P80 D-AMP clock for separate oscillation (300KHz and 350KHz)
OUT
23 AMP_MT P77 I/O D-AMP mute control (Hiz: mute off, L: mute on)
D-AMP self oscillation ON/OFF
24 AMP_CKSEL P76 O
(H: separate oscillation, L: self oscillation)
Pullup to
25 SCL_EEP P75 O EEPROM 12C SCL output for backup EEPROM
power supply
TMR-
26 FILAMENT P74 For FL filament (62.7KHz/PWM)
OUT
27 /INH_RECA P73 OUT AUX record inhibit output (L: inhibited, H: permitted)
Pullup to
28 SDA_EEP P72 OUT EEPROM 12C SDA input/output for backup EEPROM
power supply
29 iPod_RX P71 S-IN iPod RxD
30 iPod_TX P70 S-OUT iPod TxD Pullup required
31 TXD P67 Tx Data transmission terminal for Flash writing
DRX-730/NX-E700

32 RXD P66 Rx Data reception terminal for Flash writing

33 SCLK P65 S-CLK Clock terminal for Flash writing
34 BUSY P64 O BUSY output for Flash writing
35 SDATA P63 S-OUT DVD module I/F data output
36 MDATA P62 S-IN DVD module I/F data input
37 DVD_SCLK P61 S-CLK DVD module I/F clock input
38 iPod_PDET P60 I iPod accessory power detection
39 TEST P57 O For debugging (CLKOUT: sub-clock output check) Pulldown
40 iPod_DET P56 I iPod detection

39
 DRX-730/NX-E700

No. Function Name Port Name I/O Detail of Function

* Pulldown
41 EPM P55 I * Connect to GND via resistor (for Flash writing) required
(47 k-ohms)
42 P54 O VIDEO YUV/RGB selection output -> unused
VIDEO mute output (H: mute off, L: mute on)
43 VMUTE P53 O
DVD/USB input selection: mute off setting
44 SCL_VOL P52 I/O Selector/Volume I2C clock output PullUp required
45 SDA_VOL P51 I/O Selector/Volume I2C data output PullUp required
* Pullup
46 CE P50 I * Connect to Vcc2 via resistor (for Flash writing)
required
47 P47 I Pulldown
48 P46 I Pulldown
49 P45 I Pulldown
DOCK adapter power supply control
50 DOCK_POWER P44 O
(H: power on, L: power off)
51 /HPMT P43 O AMP/HP mute output (H: mute off, L: mute on)
52 /SWMT P42 O SW mute output (H: mute off, L: mute on)
USB power supply control ENABLE output
53 USB_EN P41 O
(H: enable, L: disable)
USB power supply control protection input
54 USB_PRT P40 I
(H: when normal, L: when abnormal)
55 TUNED P37 I TUNED detection (L: with signal)
56 STEREO P36 I STEREO detection (L: STEREO)
57 TMUTE P35 O TUNER MUTE output (H: mute on)
58 TUDO P34 O PLL IC serial dataoutput
59 TUCK P33 O PLL IC serial clock output
60 TUDI P32 I PLL IC serial data input
61 TUCE P31 O PLL IC serial CE output
62 VCC2 – Power supply +5V
63 P30 I Pulldown
64 VSS – GND
65 DA_ZFLG P27 I DAC Zero Flag detection (H: zero detected)
66 DA_LATCH P26 O DAC serial CE output
67 DVDMUTE_EN P25 O DVD MUTE ENABLE output (H: enable, L: disable)
68 RDS_RST P24 O RDS IC reset output (H: reset, L: usual operation)
Power supply control output for DVD
69 DVD_PS P23 O
(H: output on, L: output off)
Main unit power (relay) control output
70 PRY P22 O
(H: relay on, L: relay off)
71 RDS_READY P21 I RDS IC READY input (H: with data, L: without data) PullUp required
72 HPDET P20 I HP detection (H: HP inserted)
73 REM P17 INT-IN Remote control reception interrupt
74 STBY P16 INT-IN STANDBY/ON SW input interrupt (H: SW on)
AD KEY detection interrupt (Arrange detection key voltage
DRX-730/NX-E700

75 KEY_DET P15 INT-IN to 0.2Vcc or lower)

* Connect to AD KEY input terminal
76 RDS_RDCL P14 O RDS serial clock output
77 GSDT P13 O General purpose serial data output (FLD/DAC)
78 RDS_RDDA P12 I RDS serial data input
79 GSCK P11 O General purpose serial clock output (FLD/DAC)
80 FL_CE P10 O FL driver IC CE output
81 /ICFL P07 O FL driver IC RESET output (L: RESET)
82 LED_H P06 O LED output HDMI (H: lit)

40
 DRX-730/NX-E700

No. Function Name Port Name I/O Detail of Function

83 LED_P P05 O LED output PROGRESSIVE (H: lit)
84 LED_T P04 O LED output TIMER (H: lit)
85 IREB P03 I Encoder input INPUT
86 IREA P02 I Encoder input INPUT
87 VREB P01 I Encoder input VOLUME
88 VREA P00 I Encoder input VOLUME
89 KEY0 P107 A-D IN AD KEY input [0 to VREF]
90 DOCK_SEL P106 A-D IN DOCK discrimination [0 to VREF]
DVD module power voltage detection input
Pulldown
91 DVD_VDET P105 A-D IN (2.4V or higher: when normal, lower than
[0 to VREF]
24V: when abnormal)
92 DC_PRT P104 A-D IN D-AMP protection detection (DC detection) [0 to VREF]
93 PSPRT3 P103 A-D IN Power voltage detection 3 (PS3 protect) IN [0 to VREF]
94 PSPRT2 P102 A-D IN Power voltage detection 2 (PS2 protect) IN [0 to VREF]
95 PSPRT1 P101 A-D IN Power voltage detection 1 (PS1 protect) IN [0 to VREF]
96 AVSS – Connect to VSS (GND)
97 DEST P100 A-D IN AD destination discrimination [0 to VREF]
98 VREF – A-D, D-A reference voltage input
99 AVCC – Connect to VCC terminal (+3.3V)
100 P97 I Pulldown

Destination for AD port

Pull-up resistance 10 k-ohms
ohm 0 + 2.7 k + 6.8 k + 15.0 k + 47.0 k
V 0 - 0.5 0.5 - 1.6 1.6 - 2.5 2.5 - 3.6 3.6 - 5.0
Value 0 - 50 50 - 160 160 - 250 250 - 360 360 - 500
pin 97 (DEST) U, C G, F L, V K, A T

Key input for AD port

Pull-up resistance 10 k-ohms
ohm 0 + 1.2 k + 1.2 k + 7.9 k + 12.7 k + 20.7 k ∞
V 0 - 0.2 0.3 - 0.7 0.8 - 1.7 1.8 - 2.7 2.8 - 3.2 3.3 - 4.2 4.7 - 5.0
Value 0 - 20 30 - 70 80 - 170 180 - 270 280 - 320 330 - 420 470 - 500
(SEARCH/SKIP -
pin 89
OPEN/CLOSE PLAY/PAUSE STOP and SEARCH/SKIP - SEARCH/SKIP + KEY OFF
(KEY0)
SEARCH/SKIP +)

DRX-730/NX-E700

41
 DRX-730/NX-E700

IC801: M66003-0131FP (SUB P.C.B.)

FL display driver

Display code
RAM CGROM
(35 bit x 166) 44 SEG00
(8-bit x 60)
Code Segment 19 SEG25
write output 17 SEG26
circuit
dot data CGROM 9 SEG34
CS 2 Serial data write (35 bit x 16)
SCK 3 receive
circuit Code/
SDATA 4 command
control 45 SEG35
circuit DIG11/
52
SEG42
51 DIG12/
SEG41
code Segment DIG13/
select 50
digit SEG40
select/ 49 DIG14/
XIN 7 Clock output SEG39
timing Display
generator clock
controller scan pulse circuit 48 DIG15/
XOUT 6
SEG38
47 DIG16/
SEG37
46 DIG17/
SEG36

63 DIG00
Digit
RESET 1 output
Vcc1 8 circuit
53 DIG10
Vcc2 18
Vss 5
Vp 64
DIG14/SEG39
DIG12/SEG41
DIG13/SEG40
DIG11/SEG42
DIG07
DIG06

DIG08
DIG05
DIG00

DIG09
DIG04
DIG02
DIG03

DIG10
DIG01
VP

64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49

RESET 1 48 DIG15/SEG38
CS 2 47 DIG16/SEG37
SCK 3 46 DIG17/SEG36
SDATA 4 45 SEG35
Vss 5 44 SEG00
XOUT 6 43 SEG01
XIN 7 42 SEG02
Vcc1 8 41 SEG03
SEG34 9 40 SEG04
SEG33 10 39 SEG05
SEG32 11 38 SEG06
SEG31 12 37 SEG07
SEG30 13 36 SEG08
DRX-730/NX-E700

SEG29 14 35 SEG09
SEG28 15 34 SEG10
SEG27 16 33 SEG11
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
SEG26
Vcc2
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12

42
 DRX-730/NX-E700

Function
No. Port Name I/O Detail of Function
Name
1 RESET /RESET Reset input When “L”, M66003 is initialized.
2 CS /CEFL Chip select input When “L”, communication with the MCU is possible.
3 SCK CKFL Shift clock input When “H”, any instruction from the MCU is neglected.
4 SDATA DTFL Serial data input Serial input data is taken and shifted by the positive edge of SCK.
5 Vss VSS GND (0V)
6 XOUT XOUT Clock out When use as a CR oscillator, connect external resistor and capacitor.
7 XIN XIN Clock in When use an external clock input external clock to XIN, and XOUT must be opened.
8 Vcc1 VDD Positive power supply for internal logic.
9 SEG34 P1I
10 SEG33 P2
11 SEG32 P3
12 SEG31 P4
13 SEG30 P5 Segment output Connect to segment (anode) pins of VFD.
14 SEG29 P6
15 SEG28 P7
16 SEG27 P8
17 SEG26 P9
18 Vcc2 VDD Positive power supply for DIG and SEG outputs.
19 SEG25 P10
20 SEG24 P11
21 SEG23 P12
22 SEG22 P13
23 SEG21 P14
24 SEG20 P15
25 SEG19 P16
26 SEG18 P17
27 SEG17 P18I
28 SEG16 P19
29 SEG15 P20
30 SEG14 P21
31 SEG13 P22
32 SEG12 P23
Segment output Connect to segment (anode) pins of VFD.
33 SEG11 P24
34 SEG10 P25
35 SEG09 P26
36 SEG08 P27
37 SEG07 P28
38 SEG06 P29
39 SEG05 P30
40 SEG04 P31
41 SEG03 P32
42 SEG02 P33
43 SEG01 P34
44 SEG00 P35
45 SEG35 P36
46 SEG36 P37
47 DIG16/SEG37 G17I
48 DIG15/SEG38 G16I
49 DIG14/SEG39 G15I
50 DIG13/SEG40 G14
51 DIG12/SEG41 G13
52 DIG11/SEG42 G12
53 DIG10 G11
54 DIG09 G10
55 DIG08 G9 Digital output Connect to digit (grid) pins of VFD.
56 DIG07 G8
57 DIG06 G7
58 DIG05 G6
59 DIG04 G5
60 DIG03 G4
61 DIG02 G3
62 DIG01 G2
63 DIG00 G1
64 VP VP Negative power supply to pull down.
43
 A B C D E F G H I J
DRX-730/NX-E700

1 ■ BLOCK DIAGRAM
AUDIO/VIDEO SECTION BLOCK DIAGRAM

Q3,4
IC1
12,13
AUX OUT L REC
2 R R2A15908SP IC8
Input selector IC2
3,8 MUTE
AUX IN L Phones SUB
R
4,7
HPMT • See page 55 →
SCHEMATIC DIAGRAM

Volume

Control
Tone
5,6
DOCK 27 Lch
2,9 IC21

MUTE SUBWOOFER
1,10
28 Rch SWMT
FM/AM
3 FM/AM TUNER
RDS
(G, F models)
IC4
IC26
7 AUDIO DAC 16
8
LPF SPEAKER L
PCM1753 Class-D
8
AMP
13,14
(TDA8922B)
4 IC14
4 21
LPF SPEAKER R
PORTABLE L
R

29,30,38,40,90
68,71,76,78

FL DRIVER

I2S(L/R)
55~61

XL2

20~24
IC801 44,45
77,79

80,81 10

11
TACT SW 75 SPDIF
SW801 - 805 Optical Out
(U, C, T, K, A, L, V models)
FL DISPLAY

5
REMOTE 73 3,4,5,18,35
V801

CONTROL 36,37,90 CVBS

U801 CVBS
MICROPROCESSOR VIDEO SW
INPUT 85,86
R5F3640DNFA DVD MODULE P.C.B. TS3V340
SELECTOR YPbPr or RGB
IC11 DB-VPB801 IC28
SW808 (G, F models)
87,88 YPbPr
MAIN VOLUME
SW807
HDMI
STANDBY/ON 74 (U, C, T, K, A, L, V models)
SW806
6 84 85 86 13 15 25,28
TIMER indicator VOUT
XL3
D812
HDMI indicator EEPROM RGB AV MONITOR OUT (SCART)
D809 IC29 AUDIO OUT (G, F models)
PROGRESSIVE
indicator
D810
USB

• See page 55 →
SUB
SCHEMATIC DIAGRAM DVD MECHANISM ASS'Y MAIN • See page 53 →
7 SCHEMATIC DIAGRAM

44
 A B C D E F G H I J
DRX-730/NX-E700

POWER SUPPLY SECTION BLOCK DIAGRAM

• See page 54 → • See page 53 →

SUB MAIN
SCHEMATIC DIAGRAM SCHEMATIC DIAGRAM
2

IC10
+7I +5I
BD9778HFP
D501 IGND
T501
IC9
+20D
KIA7812API +12FL,+12V,+12A
3
SW501
IC502

Q501 IC5

Control KIA7809API +10T,+9A,+9B

AC IN

-20D
IC6

KIA78M05 +5,+5A,+5FL,+5D
4
IC506

IC15

BA50D00W V+5V

IC12
+15DD 6R3V
IC503
BD9302FP
3R3V
5
-21V Q49
VP

6
T502 D513 IC27
+5SUB
+5.6V +5M
+5BU
Q48 Q47
+12_RES
Power Reset IC11
SW501
Detect 12p
Relay
7 IC11
19p

45
 A B C D E F G H I J
DRX-730/NX-E700 POINT A XL2 (Pin 11 of IC11) POINT B XL3 (Pin 13 of IC11)
DVD MODULE
(CN968)

DVDPOWER
■ PRINTED CIRCUIT BOARDS

DVDMUTE
1

XREADY
-20D

SDATA

GNDM
GNDD
GNDD
USBN
-20D

6R3V
3R3V
V+5V
ACK
MIC
AGND
AGND
+20D
MAIN (1) P.C.B. (Side A)

+/-
+20D

L
SPEAKERS
NC
VDET
GNDD
MDATA
SCLK
XDVDRST
GNDD
USBP
DOUT
GNDD
GNDM
6R3V
3R3V
V+5V
PAGND
PGND
• Semiconductor Location VGND
Ref no. Location Ref no. Location

+/-
D1 E5 D31 I4

R
SUB (1)
D3 D4 D32 I4 (W501)
D4 D4 D33 F2
2 D5 F2 D34 F2 7 8

IC20

SUBWOOFER
D7 E5 D36 G3 1 14

D9 F6 IC1 I3 1 4

OUT
SUB (1) 24 13
D10 F6 IC2 H4 (W503) OUT
3
4 5
1
IC14
COM

CB18
8 5
D12 D3 IC3 H5 IC27 IN
IC29

D13 D3 IC4 G4 +12_RES

CB19
1 12
+5SUB
D14 D3 IC5 E6 PWR_RY
+12_RES

OUT
D15 D3 IC6 G6 SUB (2)

L/R
(CB806) 1 30
D16 H3 IC7 E3 1 100 31
C

AUX
D18 G2 IC8 G3 2 1 4
IC8
IREA KEY0 A B
D22 D3 IC9 F6 FLCE IC11
8 5
3 IREB FLCK

L/R
D23 D3 IC11 E3

IN
REM
VREA FLDT 81
80 51 50
D24 D2 IC13 D4 VREB FILAMENT 4 5
11 20
+12FL

IC1
8 1
/ICFL 8

IC21
D25 D2 IC14 I2 TIMER_LED VP IC7 1

HDMI_LED +5FL 5 4
D26 D3 IC16 H5 FLG CB20
PROGRESSIVE 10 1
STBY +5M
D27 E5 IC17 E2 HPDET CGND 28 1

D29 C2 IC20 E2 AGND2 PORTABLE_L

AGND2 PORTABLE_R
HPL
D30 F3 IC21 H3 AGND1
HPR

IC2
AGND1

DOCK
CB3
+15DD
+15DD
Ref no. Location Ref no. Location Ref no. Location MGND 15 14

IC26 H5 Q21 F3 Q46 H2

CB21

DGND 1 8
4 FLG 16
IC4
9
IC27 D2 Q23 F2 Q47 D3 VP U, C, T, K, A, L, V models
IC28 I5 Q24 G2 Q48 D3 +7I
IGND

VIDEO
IC29 E2 Q28 F2 Q49 C4

PR
CB9

VIDEO OUT
Q1 G4 Q29 F2 Q50 I5
Q3 I3 Q31 F2 Q51 I5 SUB (1) 1 3
IC13

(W502)

CB23
Q4 I3 Q32 F2 Q53 I4 6 4 16 1

IC3
8
Q8 I6 Q36 F2 9

PB
Y
IC26
Q9 H3 Q37 F2 5 8
4 1
Q10 G4 Q38 E4 CB11 9 16
IC28
8 1
Q12 H3 Q39 H2

OPTICAL
DIGITAL
5 Q13 I6 Q40 D4

OUT
Q15 I5 Q41 H2
Q16 I5 Q42 H3 5 1
3 2 CB7
Q18 I6 Q43 D4 IC16

Writing port
+5USB
Q19 I5 Q44 H3 +5USB

CB17
CB12

USBD-
Q20 F3 Q45 H3 USBG
USBD+
CB4

USBG OUT
COM

OUT
IN

IC5

IC6
COM
MAIN (2) P.C.B. (Side A) SUB (2)
(CB801) IC9 IN
G, F models
IN

COM

OUT

G, F models MAIN (1)

PLL_CE
PLL_CLK
TUNER_R
TUNER_L
STEREO/MONO
10V
NC
(CB23)
BLANKING

6 DVD MODULE
FUNC_SW

TVOUTR
POINT C 1 / Q48, 2 / Q47 AGND
TVOUTR
TVOUTL

TVOUTL (CN967)

SQUEEZE
AGND
AGND
VGND
VGND
VGND
VGND
VOUT

G, F models AGND

ASPECT
VGND

GNDD
MCLK
GNDD
BCLK
GNDD
LRCK
GNDD
DATA0
GNDD
DATA1
GNDD
DATA2
GNDD

VSEL2
VBEL1

VGND
VGND
VGND
VGND
VGND
VGND
G

B
R

CY/G
Cb/B
Cr/R
P/XI
VGND

SC

SY
G

V
CB22 VGND

PLL_TXD
PLL_RXD
TGND
TUNER_MUTE
TUNER_STATION
RDS
R
VGND
Q48 (E) 1 Q48 (E) 1 VOUT
DVD MODULE FUNC_SW
BLANKING
(CN962)

CB1 MAIN (2)

Q47 (C) 2 Q47 (C) 2 TUNER (CB22)
G, F models

7
AV MONITOR OUT
(SCART)
AC cable ON AC cable OFF AC cable ON
46
 A B C D E F G H I J
DRX-730/NX-E700

MAIN (1) P.C.B. (Side B)

• Semiconductor Location
Ref no. Location
D2 I5 T, K, A, G, F, L, V models
D6 F3
D8 E6
2 D11 E4
D17 H3
D19 G2
D20 D4
D21 D4
D28 C4
D35 D3
D37 G4
D38 G2
D39 E4
D40 E4
3
IC10 E4
IC12 D4
IC15 E4
Q2 G4
Q6 I5
Q22 I3
Q25 F3
Q26 F3
Q27 I3
Q52 I4 13 1
IC15
4 Q54 I5
IC12 1 5 IC10

14 25 1 7

5 U, C, T, K, A, L, V models

MAIN (2) P.C.B. (Side B)

G, F models
6 G, F models G, F models

47
 A B C D E F G H I J
DRX-730/NX-E700

SUB (1) P.C.B. (Side A)

MAIN (1) T, K, A, G, L, F models U, C, V models

(CB19)

CGND

CB501
W503

PWR_RY
+5SUB AC IN
+12_RES

VGND
PGND
PAGND
+20D
W501

+20D
AGND
AGND

CB502
-20D
-20D

4 MAIN (1)
(CB18)

CB503
+15DD
+15DD

IC503
MGND
W502

DGND
5 FGND
-21V
+7I

IC506
IGND

MAIN (1)
(CB21) • Semiconductor Location
Ref no. Location
D501 H5
Circuit No. U, C T, K, A, G, L, F V D502 G4
L502 O X O D504 F4
6 J520-523 X O X D505 F3
X : NOT USED D506 F4
O : USED/APPLICABLE D507 F4
D510 D4
D511 D3
D513 C3
D514 E5
D515 E5
D516 D5
IC503 E5
IC506 E5
7 Q501 G4
Q502 C3

48
 A B C D E F G H I J
DRX-730/NX-E700

SUB (1) P.C.B. (Side B)

T, K, A, G, L, F models

8 1

IC502

5 9 16
K A R
IC505

• Semiconductor Location
T, K, A, G, L, F models Ref no. Location
D503 F4
D508 E3
D509 E3
6 D512 C3
D517 H3
D518 E5
D519 E5
D521 B3
IC502 F5
IC505 C5

49
 A B C D E F G H I J
DRX-730/NX-E700

SUB (2) P.C.B. (Side A)

• Semiconductor Location
Ref no. Location
TIMER indicator D809 H3
D810 H3
D812 H3
3 HDMI indicator

PROGRESSIVE indicator

OPEN/
CLOSE
4 PLAY/ STOP
PAUSE

PHONES PORTABLE

USB

JK802

JK801
CB807

VOLUME INPUT
CB801
5 CB806 STANDBY/
ON

KEY0
FLCE
FLCK
FLDT
FILAMENT
+12FL
VP
+5FL
FLG
+5M
CGND
PORTABLE_L
PORTABLE_R
HPL
HPR

USBD+
USBD-
+5USB
USBG
USBG
+5USB
IREA
IREB
REM
VREA
VREB
/ICFL
TIMER_LED
HDMI_LED
PROGRESSIVE
STBY
HPDET
AGND1
AGND1
AGND2
AGND2
MAIN (1)
(CB12)

6
MAIN (1)
(CB20)

50
 A B C D E F G H I J
DRX-730/NX-E700

SUB (2) P.C.B. (Side B)

• Semiconductor Location
Ref no. Location
33 32 D801 D5
D802 D5
D803 D5

IC
3 48 17 D804 D5

80
1
49 16
D811 C4
IC801 F3
Q801 E3
64 1
Q802 H4
Q803 H4
Q804 H3
Q805 C4
Q806 C4
Q807 C4
4

51
 DRX-730/NX-E700

■ PIN CONNECTION DIAGRAMS

• ICs • Diodes
74AHCT541PW TSSOP BA50DD0WHFP BD9302FP-E2 BD9778HFP 1SR154-400 1SS355 D1NL20U-5083 D5SBA60
D1FK60-5063 1SS380 D1NL40-7083
RB051L-40

13 Anode
Anode
10
25
1 ANODE
20 1

5 1 7
1 Cathode –
Cathode
CATHODE +
KIA78L05F-RTF/P KIA78M05F KIA7809API-U/P L6566BTR
KIA7812API R2A15908SP D5S9M MA8030 3.0V MTZJ22D P6KE200ARL
MA8039-H 4.0V
MA8051-M 5.1V
MA8062-M 6.2V Anode Anode
Anode
14 MA8068-M 6.8V
1: OUTPUT MA8100-H 10.3V
1 2: COMMON (CASE) 1: INPUT 28
2
3 3: INPUT 2: COMMON IN MA8200-M 20.0V
1 3: OUTPUT OUT
3 COM
1
MAZ8220GHL Cathode
1 Cathode Cathode
2
3
LC72725KM-UY-TLM-E M24C02-WDW6TP M66003-0131FP-R MIC2005-0.5YM6 NJM431U NJM4565M
PCM1753DBQR NJM4580E
S1NB20 1A 200V STTH110A STPS20150CFP UDZS12B
TS3V340PWR PW
48 33
49 32

4 AC Anode
1
6 2 Anode
8 3 3
8 4
64 17 1
16 1 1: REFERENCE 8 4 AC A1
– K
1 16 2: ANODE A2
1 1 + Cathode Cathode
3: CATHODE A1
K
A2

R5F3640DNFA TC7SH04FU-TE85L TC7SH08FU TC74VHC74FT TDA8922BTH

80 51

81 50

• Transistors
4 4
5 5
12 2SA1037K 2SA1708 2SC2412K 2SD1938F 2SK3679-01 MR ST
3 3 14
7 24 KTA1504S
100 31 1 1
1
1
1 30

C C
C

E E
E
B B
C B B G
E DS

2SK3683-01MR DTA144EKA KTC3199YT

DTC144EKA

1 1: GND
2: IN
1: GATE 2 3: OUT B
12 2: DRAIN C
3 3: SOURCE E

52
 A B C D E F G H I J K L M N
DRX-730/NX-E700
SCHEMATIC DIAGRAMS
MAIN
1

To TUNER

CB4
DVD IN

9.5
RDS
4.8

2.5

2.5

4.8

1.7

1.3

1.6
2
IC26

0
4.8
4.8

IC4
IC3

0
4.8

4.8
IC26

4.8

1.5
2.4
4.8
0

ANALOG OUT -12.0

0
-20.2
20.2
0
11.5
19.9

IC27: KIA78L05F-RTF/P
0 0
-20.5
0 0 0

SPEAKERS
-8.0
-17.0

0 -20.2
Three terminal positive voltage regulator
9.5 4.8 -20.5
0 3 INPUT
9.5 0 0 Q14
-11.5 Q3 Q5

IC14
-19.9
0
20.2 Q1
5.3 Q12

R12
-20.2 0
12.0 Q13

R9
4.8 6.2
IC21
6.2 6.2
6.2
IC21
6.2 0 0 0 Q4 Q6 Q11
6.2
-20.2

R4
C1
Z1 Q16

R8

R7
0 -10.2 -10.2
0 Q10

R1

R2
AUX IN
19.8 1 OUTPUT

R10
0 Q9

R5
4.7 4.7
-16.9
Q2 Q7 Q8
4.7 4.7

R11
4.7 4.7

R3

R6
0
Z2

IC2
4.7 4.7
0 0
0.7
4.7 4.7
-16.9
2 COMMON
4.7 0 -20.2
4.7
0
4.7 4.7 0.7 4.9
0

SUBWOOFER
4.7 4.7 4.9
0
IC28: TS3V340PWR PW
AUX

4.7 0
-20.2

4.7
4.7 4.9

4.9
Quad SPDT high-band width video switch

OUT
0

9.5
0
4.7 0 with low and flat on-state resistance
IC1 4.7 4.7
4.7
0 -10.1 4.7 9.4
4.7
4 2
6.2 DA S1A
12.0

SUBWOOFER OUT
0 12.0 -20.1
IC8 4.9
12.0 6.2 6.2
0 3
0 0
S2A

INPUT
-12.0
-14.6 -12.6
0 -10.1 6.8 -0.7 0 -0.7
4.7 0 -20.1

M2
IC1 6.2

SELECTOR/
6.2 0 CB18 7 5
4.7 12.1 15.6 -20.2 -19.5
0 4.7 DB S1B
IC15

to SUB (1)_W501
VOLUME/
0
0 IC9
6
S2B
0 -0.7

TONE CONTROL
0
12.1

6.1

Page 54
-0.7 0
0 9 11

5.0
6.2
4
6.2
IC8
DC S1C
6.2

No replacement part available.

0
6.2
0 IC10 0
10
6.3
S2C
1.4 6.3 6.3

サービス部品供給なし 10.3 17.5 12 14 IN 1 16 VCC

11.0
-0.3

0
0
0.6 6.3
DD S1D S1A 2 15 EN

-0.3
-0.3

0
0 0

IC12
0.6 11.0 0
12.2 S2A 3 14 S1D
13
11.1 1.9 12.2 S2D DA 4 13 S2D
0 0 S1B 5 12 DD
0
0 S2B 6 11 S1C

M5
IC5 12.2
1
1.9 12.2 IN DB 7 10 S2C
9.6 10.3

to SUB (1)_W502
Control
17.5 12.2 GND 8 9 DC
15 Logic
-0.3
0 8.1 -22.8 EN
1.3

POINT A XL2 (Pin 11 of IC11) POINT B XL3 (Pin 13 of IC11)

1.1 3.3

Page 54
0 0 3.3 -22.2 -27.0
0.7
0 3.3 0
0
2 1
DOCK

CB21
C
IC29: M24C02-WDW6TP
5.0 8.9
4.8
0 2 K-bit serial I2C bus EEPROM
12.1 12.1
1.9 1.9
IC6 11.5
4.9 4.9
0 0 V CC
3.3 4.9 0

5.0 8.9
3.9

5
0 7.4 6.9
0 0 0
3

0
E0-E2 SDA E0 1 8 V CC
0 0
E1 2 7 WC
SCL M24Cxx
5.0 11.7 12.2 E2 3 6 SCL
4.9 5.0 IC27 WC V SS 4 5 SDA

M7
OPTICAL

5.0 5.0
DIGITAL

to SUB (1)_W503
5.6 10.7
0
-10.1 4.8 5.0
4.8 4.8 CB19

-10.1
4.8 5.6 V SS

DIGITAL OUT

Page 54
0.7
0

4.8
POINT C 1 / Q48 , 2 / Q47 IC16: TC7SH08FU

5.1
4.8

4.8
5.0

0
0

4.9

0
4.7

4.8
0.2

5.0

4.7

4.9

5.1

4.8

4.8
0

4.8

5.5
5.5
5.0

0
5.0 0

-10.1
4.9 4.8 5.0 0 2-input AND gate
4.8 4.8 0
-10.1 0
0 0
3.3 0
0
IN B 1 5 V CC
0 0

5.0

MICROPROCESSOR
0 5.0
4.9
IN A 2
5.0
VIDEO OUT

5.0
5.0 4.9
Q48 (E) 1 Q48 (E) 1 GND 3 4 OUT Y
6 2.8

4.8
5.0
0

IC11
4.8

0
0

4.8
-10.1 4.8 CB20
3.2
IC28
2.6 0
0
2.0
5.0 3.6 5.0 Q47 (C) 2 Q47 (C) 2 IC17: TC7SH04FU-TE85L
2.8 0
-20.5
0 0
Inverter
2.0 0

4.8 A B 0
NC 1 5 VCC
4.8 0
0 4.9

IC7
0 0
0 0
IN A 2 A Y
0 0
AC cable ON AC cable OFF AC cable ON

I6
to SUB (2)_CB806
VIDEO SW
0.2
L H

4.8
0 0.2
GND 3 4 OUT Y

4.9
3.2 4.3 2.0 3.6 2.9
H L

4.1

4.8

5.0

1.0

1.2

4.8

2.5
0

2.2

4.8

4.4

2.4

4.8

4.9
0

0
0
4.8
0 5.0

Page 55
0 0 0 0 0

IC14: TDA8922BTH

0.2
0 0

0 0
2 x 50 W class-D power amplifier

0
IC20: TC74VHC74FT

0
0

0
VDDA2 VDDA1 STABI PROT VDDP2 VDDP1

5.0
7 Dual D-type flip flop with preset and clear 3(20) 10(4) 18(12) 13(7) 23(16) 14(8)
3.3 IC20 IC29 15(9)
3.3
BOOT1
CB22 4.9
IC16
5.0 9(3) RELEASE1
IN1M DRIVER
14 VCC INPUT PWM

0
0 1CLR 1 HIGH

2.4
2.5 SWITCH1
AV MONITOR OUT

8(2) STAGE MODULATOR CONTROL 16(10)

5.0

0
0
2.4 IC17 5.0 Inputs Outputs IN1P AND OUT1
1D 2 13 2CLR Function ENABLE1 HANDSHAKE
0
CK D CLR PR D CK Q Q DRIVER
mute LOW
G, F models

11(5)
CB1

0 Q Q
1CK 3 12 2D L H X X L H Clear SGND1 STABI
VSSP1
Preset

EEPROM
1PR 4 11 2CK H L X X H L 7(1)
OSC TDA8922BTH
_ TEMPERATURE SENSOR
L L X X H H OSCILLATOR MANAGER (TDA8922BJ) VDDP2
1Q 5 10 2PR 6(23) CURRENT PROTECTION
_ MODE MODE VOLTAGE PROTECTION
H H L L H 22(15)
CK D BOOT2
1Q 6 9 2Q _
Q Q H H H H L 2(19)
SGND2 ENABLE2 DRIVER
GND 7 8 2Q H H X Qn Qn No Change mute HIGH
CONTROL 21(14)
5(22) SWITCH2 AND OUT2
X:Don’t care IN2P
(top view) INPUT PWM HANDSHAKE
RELEASE2 DRIVER
CB23 4(21) STAGE MODULATOR
5.1 LOW
0 IN2M

0 5.1 1(18) 12(6) 24(17) 19(-) 17(11) 20(13)

COB 022

0
IC13
5.1 VSSA2 VSSA1 VSSD n.c VSSP1 VSSP2

IC12: BD9302FP-E2
(1) Pin numbers in parenthesis refer to the TDA8922BJ.

2.5 MHz 2 A power switch 2 ch step-down switching regulator

8
MAIN (2) G, F models
PGND1 1 25 SW1L
IC2: R2A15908SP
CB11

CB12

CB17
CB7

CB9

MAIN (1)
COMP1 2 24 SW1
0.6V
+ ERR
OCP
Current
Sense
5 input selector 2 ch electronic volume with tone & surround
FB1 3 - 23 SW1
To DVD module P.C.B. To DVD module P.C.B. To DVD module P.C.B.
Writing port RT 4 DRV2
SDWN 22 BOOT1
IC3: PCM1753DBQR Page 55 C8 slope
Set
DRV1
N.C. 5 + - Reset
PWN SDWN 21 PVCC INR5 1 28 ROUT
24-bit 192 KHz sampling enhanced multi-level, delta-sigma, to SUB (2)_CB801 SS1/SD 6

audio digital to analog converter VCC 7 20 PVCC Mode selector

UXLO INR4 2 27 LOUT
VREF Internal TSD
5V

IC1: NJM4565M
Bisa
OSC
SS2/SD 8 19 PVCC
BCK
Dual operational amplifier LRCK Audio IC5: KIA7809API-U/P IC6: KIA78M05F N.C. 9
0.6V Set
SDWN 18 PVCC
INR3 3 26 TRER

IC11: R5F3640DNFA
Serial VOUTL Surround
Output Amp
Voltage regulator Three terminal positive voltage regulator + Reset
DRV1 Input

IC7: 74AHCT541PW TSSOP

DATA Port and FB2 10 - 17 BOOT2
IC10: BD9778HFP
DAC SDWN selector

Rch Bass/Treble
ERR DRV2
V+ Low-Pass Filter PWN
INR2 4 25 BASSR1

Tone control
1 INPUT
8 1 INPUT Single-chip 16-bit CMOS microprocessor + -

Octal buffer/line driver 3 state COMP2 11 16 SW2

RA

RB

slope
D2 Current
R22 R17 R23
Flexible step down switching regulator
R4

4x/8x Sense
R13_1

Oversampling R1 Q11 Q11-1 Q9 GND 12

OCP
Enhanced Q8 8 8 8 8 8 8 15 SW2
Digital
Multilevel Q15 Q12 Q15 A0 Y0
INR1 5 24 BASSR2
(FMT)ML Filter VCOM 2 18
Delta-Sigma Q16 PGND2 13 14 SW2L mute
2, 6 and
D3 R15 Q16
Function Modulator Q12
–INPUT OUTPUT Q14 R14 R14
1, 7 Control R10 R15 A1 Y1 Port P0 Port P1 Port P2 Port P3 Port P4 Port P5
Serial Q14 INL1 6 23 BASSL2
9
3 17
+INPUT (MUTE)MC
Control Q17 Q19 R16

Lch Bass/Treble
3, 5 R19 R19 ON/OFF 7 EN Mono
VIN 1
R16

Tone control
Port Output Amp R12 3 OUTPUT L:OFF VCC2 ports /Stereo
R12

(DEMP)MD DAC and Q18 Q6 R20 3 OUTPUT

4
A2 Y2
16 H:ON IC13: MIC2005-0.5YM6 INL2
Low-Pass Filter VOUTR
Q1
Q6 7 22 BASSL1
R11
R18
R7 C1
R9
D1 Q10
5
A3 Y3
15
Internal peripheral functions
UART or clock synchronous Clock generation circuit
Fixed current limit power distribution switch
QD
R20

Z1
R18

R2 Q10 serial I/O X IN-XOUT

R9

(TEST) Timer (16-bit)

V– Q2 (6-channels) INL3 21 TREL
R2

System Clock Q7 R21 Q11 A4 Y4 XCIN-XCOUT 8

4 Q13 R3 C1 6 14
R11

Under
Q1

Vref Outputs (timer A): 5 PLL frequency synthesizer Input

Q4 Clock synchronous Voltage 1 VIN
System SOFT On-chip oscillator (125 kHz) selector
SCK Q4 OE0 1 20 VCC Inputs (timer B): 6 serial I/O
Clock Zero Detect Q3 Q5 Q9 Q8 A5 Y5 START Detector Current Power
Power Supply R13 Q13 7 13
A0 2 19 OE1 Mirror FET FET INL4 9 20 DGND
R21

Manager R4 Q1 Q2 (8 bits x 2 channels) DMAC

R5 R6 R8 A1 3 18 Y0 Three-phase motor control circuit (4 channels)
R13

2 COMMON (GND) A6 Y6
R3

8 12 A2 4 17 Y1

IC4: LC72725KM-UY-TLM-E
ERROR AMP
A3 5 16 Y2 PWM CRC arithmetic circuit (CCITT) Control Logic INL5 10 19 SDA
t Open-Drain Output for the PCM1755 0
ZEROL/NAt

ZEROR/ZEROAt
(ZEROA)

DGND

VCC

AGND

A7 Y7 A4 6 15 Y3 INV 5 - COMPARATOR Watchdog timer (Polynomial : X 16+X12+X5+1) Gate Control

( ): PCM1754 9 11 - and delay Timer Input gain MCU
(15-bits)
RDS signal demodulation IC A5 7 14 Y4
+
+ LATCH DRIVER
M16C/60 series
control I/F
A6 8 13 Y5 + A/D converter Memory IGOUTL 11 18 SCL
2 SW Microprocessor core 6 VOUT
OE0
IC9: KIA7812API
RESET mute
1 A7 9 12 Y6 (10-bits X 26-channels) ROM
BCK 1 16 SCK Vref
OE1 GND 10 11 Y7 SB 0~+20dB
+3V VREF FLOUT CIN +3V 19 R0H R0L
DATA 2 15 ML
Voltage regulator OSC TSD D/A converter
(8-bits X 2-channels)
R1H R1L USP RAM
Thermal
Sensor
VOLINL 12 /2dB stepVolume
0~87dB,-∞
17 AGND
Vdda Vddd LRCK 3 14 MC R2
IC8, 21, 26: NJM4580E
CLOCK ISP
PLL 1 INPUT VIN R3
RECOVERY DGND 4 13 MD INTB
REFERENCE (57kHz) R22 R17 R23
(1187.5Hz) REF
Vssa
VOLTAGE
Vssd
NC 5 12 ZERORL/NA Dual operational amplifier R1 Q11 Q11-1
+
A0
A1
A1
PC
VREF
IGOUTR 13 0~+20dB
16 REFIN
VREF VCC 6 11 ZEROR/ZEROA FB FLG Multiplier Slew Rate /2dB step
- FB
Q15 2 GND
57kHz
IC15: BA50DD0WHFP
10
VOUTL 7 10 VCOM Control
BPF V+ Q16 Current Limit Volume
MPXIN ANTIALIASING SMOOTHING DATA RDDA
(SCF) VOUTR 8 9 AGND 8 Q12 CURRENT LIMIT 4 GND Control Loop VIN 1 6 VOUT VOLINR 14 0~87dB,-∞ 15 VCC
FILTER FILTER DECODER
RDCL
Q14
R10 R15
R14 2 A low dropout voltage regulator with shut down switch VCC1 ports Factory
GND 2 5 CSELW
Q17 Q19 adjusted
R19 R16 GND FB 3
RDS-ID/READY 1 16 RDCL Port P10 Port P9 Port P8 Port P7 Port P6
R12 3 OUTPUT ENABLE 3 4 FAULT/
RAM 8 8 8 8 8
(128bits) MODE RDDA 2 15 RST 2, 6 1, 7 OUTPUT Q18 Q6 R20 6
Vref
- +

Q1
–INPUT R18
Driver
VREF 3 14 XOUT R11 RT
RST +INPUT R9
CLK(4.332MHz) MPXIN 4 13 XIN 3, 5 Z1 R7 C1
R2 Q10 *Refer to the Technical Note about the details of the application.
RDS-ID RDS-ID/ Q2
TEST TEST Vdda 5 12 Vddd
OSC DETECT READY R3 Q7 R21
Q13
Vssa 6 11 Vssd Q4 OVP TSD OCP
7 1 2 3 4 5
FLOUT 10 MODE Q3 Q5 Q9 Q8
XIN XOUT R13 CTL VCC GND VOUT N.C.
CIN 8
V–
9 TEST R4 R5 * Please refer to technical note concerning application circuit, and etc.
4 R6 R8
2 COMMON (GND)

53
 A B C D E F G H I J K L M N
DRX-730/NX-E700

1
SUB 1/2

20.2

2 128.9

0 332.1
331.9

129.0 Page 53 J4
330.8

to MAIN (1)_CB18

431.8

W501
431.7
0 0

331.5 0 0
-2.2

IC505
3 -20.5 20.2

10.0 -20.5
0
0
1.1 0.9

-20.5

3.1
0
5.0
0
1.3 1.0
14.6 0
0 14.6

1.1 1.1
2.1 0 14.6

IC502
0

4
1.0
3.1

332.1 12.8
CB501 0

IC506 -2.2
AC IN 0

CONTROL
0

CB502 CB503
3.1

-3.2

IC503 -27.0
14.6

0 -27.0 0

5 0
Page 53 J4
-27.0
to MAIN (1)_CB21

W502

0 -27.0

-0.2 11.3

4.7 14.7

AC10.0 4.7 14.6

10.7
Page 53 J5
12.1
4.8 4.7 to MAIN (1)_CB19

0
0

7
0
0.7

SUB (1)

IC502: L6566BTR
Multi mode controller for SMPS

VREF SS AOMP VFF

10 14 9 15
15 uA 6.4V
IC505: NJM431U TIME - OVPL

9 SOFT-START OVP
OUT LOW CLAMP OFF2 1 mA
Adjustable precision shunt regulator HV 1 &
FAULT MNGT
& DISABLE +

7.7V
LINE VOLTAGE Q
Reference FEEDFORWARD
VOLTAGE
REGULATOR voltages CS
LEB 7
Vcc 5 & Internal supply
ADAPTIVE UVLO UVLO 1.5 V
- + - + + -
VIn PWM OCP Vcc
Vcc

UVLO_SHF
400 uA +
FMOD 6
- - Hiccup-mode
OCP logic 14V
+ 5.7V BURST-MODE
OCP2
4 GD
1 2 3 OSC 13 OSCILATOR R
Q DRIVER
MODE SELECTION S
MODE/SC 12 &
REFERENCE ANODE CATHODE TURN-ON LOGIC
TIME
50 mV ZERO CURRENT
- OUT OVPL
100 mV DETECTOR

ZCD 11 + 4.5V

10
OFF2 -
OVERVOLTAGE OVP
LATCH
PROTECTION + 8 GIS
IC_LATCH

AC_OK 16 - AC_FAIL
DISABLE
15 uA 0.450V
3V +
0.485V UVLO

3
GND

54
 A B C D E F G H I J K L M N
DRX-730/NX-E700

SUB 2/2
1

-14.9

-20.5

-20.3

-22.2

-17.5

-17.2

-17.2

-22.2

-22.2

-22.2

-22.2

-22.2

-22.2

-22.2

-19.0

-22.1

-17.2

-14.2

-14.9
-22.2

-20.6

-20.6

-20.6

-20.6

-20.6
18.9
-20.5

-20.6

-20.5

-20.5

-20.6

-20.6

-20.5

-20.5

-20.6

~
2

-22.2

-22.2

-22.2

-22.2

-22.2

-19.0

5.0
~

~
11.5

~ -22.1 4.9

~ ~
4.8
3 -22.2 -17.2 4.9
0.3
-20.6 -14.2

~ ~
0
-18.9 ~ 0
~ ~ -16.1
-22.2 IC801 ~

-17.2 5.0 -22.3

-17.2 2.2

-17.5 2.2
VOLUME INPUT
-22.2 0
0

4.8

4 5.0
4.7

-20.6 4.8
-20.6

-20.3

-20.6

-22.2

-20.6

-20.5

-20.5

-20.6

-20.6

-20.5

-20.5

-20.6

-20.5

-22.3
-20.5

-20.6

-20.6

-20.6

JK801

5.0

5.0
PORTABLE

JK802

Page 53 J6
to MAIN (1)_CB20

PHONES

7
5.0 5.0

0 0 0 0 IC801: M66003-0131FP-R
18 digit 5 x 7 segment VFD controller/driver

0 0 0 0 3.5 3.5 3.9

USB Display code
RAM CGROM
0 0 0 (35-bit x 166) 44 SEG00
(8-bit x 60)
Code Segment 19 SEG25
write output 17 SEG26
circuit
dot data CGROM 9 SEG34
CS 2 Serial data write (35-bit x 16)
0 0 0 SCK 3 receive
circuit Code/
SDATA 4 command
control 45 SEG35
circuit DIG11/
52
SEG42
51 DIG12/
CB806 SEG41
8 code
select
Segment/
Digit 50 DIG13/
SEG40
select/ DIG14/
CB801

49
XIN 7 Clock output SEG39
timing Display
generator clock
controller scan pulse circuit 48 DIG15/
XOUT 6 SEG38
47 DIG16/
SEG37
DIG17/

SUB (2)
46
SEG36

63 DIG00
Digit
RESET 1 output
Page 53 H8 circuit
Vcc1 8 53 DIG10
to MAIN (1)_CB12 Vcc2 18
Vss 5
Vp 64

10

55
 DRX-730/NX-E700

■ REPLACEMENT PARTS LIST

• ELECTRICAL COMPONENT PARTS
WARNING
● Components having special characteristics are marked and must be replaced with parts having specifications
equal to those originally installed.
● The chip resistor is not supplied as a replacement part.
* When a chip resistor is necessary, use the following part.
AAX60720: CHIP RESISTOR SAMPLE BOOK

ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS:

C.A.EL.CHP : CHIP ALUMI.ELECTROLYTIC CAP L.EMIT : LIGHT EMITTING MODULE
C.CE : CERAMIC CAP LED.DSPLY : LED DISPLAY
C.CE.ARRAY : CERAMIC CAP ARRAY LED.INFRD : LED,INFRARED
C.CE.CHP : CHIP CERAMIC CAP MODUL.RF : MODULATOR,RF
C.CE.ML : MULTILAYER CERAMIC CAP PHOT.CPL : PHOTO COUPLER
C.CE.M.CHP : CHIP MULTILAYER CERAMIC CAP PHOT.INTR : PHOTO INTERRUPTER
C.CE.SAFTY : RECOGNIZED CERAMIC CAP PHOT.RFLCT : PHOTO REFLECTOR
C.CE.TUBLR : CERAMIC TUBULAR CAP PIN.TEST : PIN,TEST POINT
C.CE.SMI : SEMI CONDUCTIVE CERAMIC CAP PLST.RIVET : PLASTIC RIVET
C.EL : ELECTROLYTIC CAP R.ARRAY : RESISTOR ARRAY
C.MICA : MICA CAP R.CAR. : CARBON RESISTOR
C.ML.FLM : MULTILAYER FILM CAP R.CAR.CHP : CHIP RESISTOR
C.MP : METALLIZED PAPER CAP R.CAR.FP : FLAME PROOF CARBON RESISTOR
C.MYLAR : MYLAR FILM CAP R.FUS : FUSABLE RESISTOR
C.MYLAR.ML : MULTILAYER MYLAR FILM CAP R.MTL.CHP : CHIP METAL FILM RESISTOR
C.PAPER : PAPER CAPACITOR R.MTL.FLM : METAL FILM RESISTOR
C.PLS : POLYSTYRENE FILM CAP R.MTL.OXD : METAL OXIDE FILM RESISTOR
C.POL : POLYESTER FILM CAP R.MTL.PLAT : METAL PLATE RESISTOR
C.POLY : POLYETHYLENE FILM CAP RSNR.CE : CERAMIC RESONATOR
C.PP : POLYPROPYLENE FILM CAP RSNR.CRYS : CRYSTAL RESONATOR
C.TNTL : TANTALUM CAP R.TW.CEM : TWIN CEMENT FIXED RESISTOR
C.TNTL.CHP : CHIP TANTALUM CAP R.CEMENT : CEMENT RESISTOR
C.TRIM : TRIMMER CAP SCR.BND.HD : BIND HEAD B-TIGHT SCREW
CN : CONNECTOR SCR.BW.HD : BW HEAD TAPPING SCREW
CN.BS.PIN : CONNECTOR,BASE PIN SCR.CUP : CUP TIGHT SCREW
CN.CANNON : CONNECTOR,CANNON SCR.TERM : SCREW TERMINAL
CN.DIN : CONNECTOR,DIN SCR.TR : SCREW,TRANSISTOR
CN.FLAT : CONNECTOR,FLAT CABLE SUPRT.PCB : SUPPORT,P.C.B.
CN.POST : CONNECTOR,BASE POST SURG.PRTCT : SURGE PROTECTOR
COIL.MX.AM : COIL,AM MIX SW.TACT : TACT SWITCH
COIL.AT.FM : COIL,FM ANTENNA SW.LEAF : LEAF SWITCH
COIL.DT.FM : COIL,FM DETECT SW.LEVER : LEVER SWITCH
COIL.MX.FM : COIL,FM MIX SW.MICRO : MICRO SWITCH
COIL,OUTPT : OUTPUT COIL SW.PUSH : PUSH SWITCH
DIOD.ARRAY : DIODE ARRAY SW.RT.ENC : ROTARY ENCODER
DIODE.BRG : DIODE BRIDGE SW.RT.MTR : ROTARY SWITCH WITH MOTOR
DIODE.CHP : CHIP DIODE SW.RT : ROTARY SWITCH
DIODE.VAR : VARACTOR DIODE SW.SLIDE : SLIDE SWITCH
DIOD.Z.CHP : CHIP ZENER DIODE TERM.SP : SPEAKER TERMINAL
DIODE.ZENR : ZENER DIODE TERM.WRAP : WRAPPING TERMINAL
DSCR.CE : CERAMIC DISCRIMINATOR THRMST.CHP : CHIP THERMISTOR
FER.BEAD : FERRITE BEADS TR.CHP : CHIP TRANSISTOR
FER.CORE : FERRITE CORE TR.DGT : DIGITAL TRANSISTOR
FET.CHP : CHIP FET TR.DGT.CHP : CHIP DIGITAL TRANSISTOR
FL.DSPLY : FLUORESCENT DISPLAY TRANS : TRANSFORMER
FLTR.CE : CERAMIC FILTER TRANS.PULS : PULSE TRANSFORMER
FLTR.COMB : COMB FILTER MODULE TRANS.PWR : POWER TRANSFORMER ASS’Y
FLTR.LC.RF : LC FILTER,EMI TUNER.AM : TUNER PACK,AM
GND.MTL : GROUND PLATE TUNER.FM : TUNER PACK,FM
DRX-730/NX-E700

GND.TERM : GROUND TERMINAL TUNER.PK : FRONT-ENDTUNER PACK

HOLDER.FUS : FUSE HOLDER VR : ROTARY POTENTIOMETER
IC.PRTCT : IC PROTECTOR VR.MTR : POTENTIOMETER WITH MOTOR
JUMPER.CN : JUMPER CONNECTOR VR.SW : POTENTIOMETER WITH ROTARY SW
JUMPER.TST : JUMPER,TEST POINT VR.SLIDE : SLIDE POTENTIOMETER
L.DTCT : LIGHT DETECTING MODULE VR.TRIM : TRIMMER POTENTIOMETER

57
 DRX-730/NX-E700

P.C.B. MAIN
Ref No. Part No. Description Markets Ref No. Part No. Description Markets
* WQ228200 P.C.B. MAIN UC C76-77 US135100 C.CE.CHP 0.1uF 16V
* WQ228300 P.C.B. MAIN T C78-82 UR866100 C.EL 1uF 50V
* WQ228400 P.C.B. MAIN K C83 UR847100 C.EL 10uF 25V
* WQ228500 P.C.B. MAIN A C84-85 UA352220 C.MYLAR 220pF 50V
* WQ228600 P.C.B. MAIN GF C86-87 UR866220 C.EL 2.2uF 50V
* WQ228700 P.C.B. MAIN L C89-90 US063100 C.CE.CHP 1000pF 50V B
* WQ228800 P.C.B. MAIN V C94-95 UA353220 C.MYLAR 2200pF 50V
CB1 WB497100 CN.RGB 21P YKF41-5044 GF C97 UR838100 C.EL 100uF 16V
CB4 VM923600 CN.BS.PIN 13P C98-99 UU247100 C.EL 10uF 25V
CB7 WC196700 CN 17P TE C104 US135100 C.CE.CHP 0.1uF 16V
CB9 WC196300 CN 13P TE C105 UR838470 C.EL 470uF 16V
CB11 WC199700 CN 52808 27P TE C106 UA353820 C.MYLAR 8200pF 50V
CB12 WC195600 CN 6P TE FMN C107-108 UA354680 C.MYLAR 0.068uF 50V
CB17 VQ044400 CN.BS.PIN 9P C109 UR847100 C.EL 10uF 25V
CB18 LB918090 CN.BS.PIN 9P C110-111 UR838100 C.EL 100uF 16V
CB19 VB390000 CN.BS.PIN 4P C112 Vi912500 C.EL 10uF 25V
CB20 V4415100 CN 30P TP C113 US135100 C.CE.CHP 0.1uF 16V
CB21 VL845200 CN.BS.PIN 8P C114-115 UA354680 C.MYLAR 0.068uF 50V
CB22-23 WC196400 CN 14P TE GF C116 UA353820 C.MYLAR 8200pF 50V
C1 US046100 C.CE.CHP 1uF 25V C117 UU218470 C.EL 470uF 6.3V
C2 US062100 C.CE.CHP 100pF 50V B C118 Vi912500 C.EL 10uF 25V
C3-5 US060800 C.CE.CHP 8pF 50V B C119 US135100 C.CE.CHP 0.1uF 16V
C7-10 US062100 C.CE.CHP 100pF 50V B C120 UR837470 C.EL 47uF 16V
C13-14 UA352220 C.MYLAR 220pF 50V C121 US061330 C.CE.CHP 33pF 50V B
C15-16 US062220 C.CE.CHP 220pF 50V B C122 UA352100 C.MYLAR 100pF 50V
C17 US062220 C.CE.CHP 220pF 50V B GF C123 US135100 C.CE.CHP 0.1uF 16V GF
C18 UR838220 C.EL 220uF 16V C124 UR866220 C.EL 2.2uF 50V
C20 US062100 C.CE.CHP 100pF 50V B C125 US135100 C.CE.CHP 0.1uF 16V GF
C22 US062100 C.CE.CHP 100pF 50V B C126-127 Vi912500 C.EL 10uF 25V
C23-25 US060800 C.CE.CHP 8pF 50V B GF C128 UA352220 C.MYLAR 220pF 50V
C26 US062100 C.CE.CHP 100pF 50V B GF C129 UA353220 C.MYLAR 2200pF 50V
C27 UR818470 C.EL 470uF 6.3V C130 US062330 C.CE.CHP 330pF 50V B GF
C28 US135100 C.CE.CHP 0.1uF 16V C131-132 UA352100 C.MYLAR 100pF 50V
C29 US062100 C.CE.CHP 100pF 50V B C133 US062330 C.CE.CHP 330pF 50V B GF
C30 US062220 C.CE.CHP 220pF 50V B GF C134-135 UR838100 C.EL 100uF 16V
C31 US063100 C.CE.CHP 1000pF 50V B C136 Vi912500 C.EL 10uF 25V
C32-34 UR818470 C.EL 470uF 6.3V C137-138 UR847100 C.EL 10uF 25V GF
C35-36 US061330 C.CE.CHP 33pF 50V B GF C139 US135100 C.CE.CHP 0.1uF 16V
C37 UR866470 C.EL 4.7uF 50V C140 US135100 C.CE.CHP 0.1uF 16V GF
C38 UR818220 C.EL 220uF 6.3V C141 US062560 C.CE.CHP 560pF 50V B GF
C39 US062100 C.CE.CHP 100pF 50V B C142 US135100 C.CE.CHP 0.1uF 16V
C40 US062220 C.CE.CHP 220pF 50V B C143 US135100 C.CE.CHP 0.1uF 16V GF
C41-44 UR818470 C.EL 470uF 6.3V GF C144-145 UA352100 C.MYLAR 100pF 50V
C45 US062100 C.CE.CHP 100pF 50V B C146 UA354470 C.MYLAR 0.047uF 50V
C46 US135100 C.CE.CHP 0.1uF 16V C147-148 US061270 C.CE.CHP 27pF 50V B GF
C47 US062100 C.CE.CHP 100pF 50V B C149 UR819100 C.EL 1000uF 6.3V
C49 US064100 C.CE.CHP 0.01uF 50V B C150 UR867100 C.EL 10uF 50V
C51 US135100 C.CE.CHP 0.1uF 16V GF C151 UR866470 C.EL 4.7uF 50V
DRX-730/NX-E700

C53-54 US062470 C.CE.CHP 470pF 50V B C153 US135100 C.CE.CHP 0.1uF 16V
C55 US135100 C.CE.CHP 0.1uF 16V C154 UR838100 C.EL 100uF 16V
C56 UU238220 C.EL 220uF 16V C155 US135100 C.CE.CHP 0.1uF 16V
C58-59 UR847100 C.EL 10uF 25V C156 UR838220 C.EL 220uF 16V
C62 US135100 C.CE.CHP 0.1uF 16V C157 US135100 C.CE.CHP 0.1uF 16V
C64 US135100 C.CE.CHP 0.1uF 16V C158 UR848100 C.EL 100uF 25V
C66-69 UR847100 C.EL 10uF 25V C159 UR838100 C.EL 100uF 16V
C70-74 UR866100 C.EL 1uF 50V C160 US065100 C.CE.CHP 0.1uF 50V B
C75 US062100 C.CE.CHP 100pF 50V B C161 US135100 C.CE.CHP 0.1uF 16V
✻ New Parts ✻ New Parts
58
 DRX-730/NX-E700

P.C.B. MAIN
Ref No. Part No. Description Markets Ref No. Part No. Description Markets
C162 UR848100 C.EL 100uF 25V C249-250 VE326800 C.MYLAR 0.47uF 50V
C163 US135100 C.CE.CHP 0.1uF 16V C251 UR848100 C.EL 100uF 25V
C164 US065100 C.CE.CHP 0.1uF 50V B C252-253 US065100 C.CE.CHP 0.1uF 50V B
C165 US135100 C.CE.CHP 0.1uF 16V C254-257 US061330 C.CE.CHP 33pF 50V B
C166 UR848100 C.EL 100uF 25V C259 US064100 C.CE.CHP 0.01uF 50V B
C167 US065100 C.CE.CHP 0.1uF 50V B C263 US064100 C.CE.CHP 0.01uF 50V B
C168 US135100 C.CE.CHP 0.1uF 16V C265 US064100 C.CE.CHP 0.01uF 50V B
C169 UR848100 C.EL 100uF 25V C266 US135100 C.CE.CHP 0.1uF 16V
C170 WE477600 C.EL 100uF 16V C267 UR867100 C.EL 10uF 50V
C171 US046100 C.CE.CHP 1uF 25V C268 UR867330 C.EL 33uF 50V
C172 US135100 C.CE.CHP 0.1uF 16V C269-270 UR847100 C.EL 10uF 25V
C174 UR818220 C.EL 220uF 6.3V C271-272 US062100 C.CE.CHP 100pF 50V B
C175 WE477600 C.EL 100uF 16V C273-274 UU248470 C.EL 470uF 25V
C176 US063680 C.CE.CHP 6800pF 50V B C280 US064100 C.CE.CHP 0.01uF 50V B
C177 US063100 C.CE.CHP 1000pF 50V B C281-282 US135100 C.CE.CHP 0.1uF 16V GF
C178-179 US062100 C.CE.CHP 100pF 50V B C283 US065100 C.CE.CHP 0.1uF 50V B
C180 US135100 C.CE.CHP 0.1uF 16V C284-285 UR838100 C.EL 100uF 16V
C181-182 US062100 C.CE.CHP 100pF 50V B C288 US064100 C.CE.CHP 0.01uF 50V B
C183 US063100 C.CE.CHP 1000pF 50V B C291 US064100 C.CE.CHP 0.01uF 50V B
C184 US062100 C.CE.CHP 100pF 50V B C292 UR847100 C.EL 10uF 25V
C185 US063100 C.CE.CHP 1000pF 50V B C293 UR838100 C.EL 100uF 16V
C187-190 VE326800 C.MYLAR 0.47uF 50V C294 UR818100 C.EL 100uF 6.3V GF
C191 US135100 C.CE.CHP 0.1uF 16V C295 US046100 C.CE.CHP 1uF 25V
C192-193 UA352220 C.MYLAR 220pF 50V C296 US063100 C.CE.CHP 1000pF 50V B
C194-195 US065100 C.CE.CHP 0.1uF 50V B C297 UR838220 C.EL 220uF 16V
C196-197 US063330 C.CE.CHP 3300pF 50V B C298-299 US046100 C.CE.CHP 1uF 25V
C198 US046100 C.CE.CHP 1uF 25V C300 UR847100 C.EL 10uF 25V
C199 UR838100 C.EL 100uF 16V C301 US135100 C.CE.CHP 0.1uF 16V
C200 US061100 C.CE.CHP 10pF 50V B C302-305 US062220 C.CE.CHP 220pF 50V B
C203 US061270 C.CE.CHP 27pF 50V B C306 UR818470 C.EL 470uF 6.3V
C204-208 US065100 C.CE.CHP 0.1uF 50V B C307 US064100 C.CE.CHP 0.01uF 50V B
C209 US062100 C.CE.CHP 100pF 50V B C309 US135100 C.CE.CHP 0.1uF 16V
C210 US064100 C.CE.CHP 0.01uF 50V B C310-311 US046100 C.CE.CHP 1uF 25V
C211 US061330 C.CE.CHP 33pF 50V B C312-313 US062100 C.CE.CHP 100pF 50V B
C212 US135100 C.CE.CHP 0.1uF 16V C317-318 US135100 C.CE.CHP 0.1uF 16V
C213-214 US065100 C.CE.CHP 0.1uF 50V B C321-323 US063100 C.CE.CHP 1000pF 50V B
C215-216 US046100 C.CE.CHP 1uF 25V C325 UR818470 C.EL 470uF 6.3V
C217 UR847470 C.EL 47uF 25V D1 VT332900 DIODE 1SS355
C218 US135100 C.CE.CHP 0.1uF 16V D2 VU991500 DIODE.ZENR MA8039-H 4V
C219-220 US046100 C.CE.CHP 1uF 25V D3-4 VT332900 DIODE 1SS355
C221 US064150 C.CE.CHP 0.015uF 50V B D5 VU995500 DIODE.ZENR MA8100-H 10.3V
C222 US065100 C.CE.CHP 0.1uF 50V B D6-10 VT332900 DIODE 1SS355
C223 US064150 C.CE.CHP 0.015uF 50V B D11 V6267600 DIODE RB051L-40
* C224-225 WE477400 C.EL 47uF 16V D12-16 VU992600 DIODE.ZENR MA8051-M 5.1V
C226 US062220 C.CE.CHP 220pF 50V B D17-18 VT332900 DIODE 1SS355
C227-228 US065100 C.CE.CHP 0.1uF 50V B D19 VU990400 DIODE.ZENR MA8030 3V
C229 UR867470 C.EL 47uF 50V D20-21 V6267600 DIODE RB051L-40
C230-233 US065100 C.CE.CHP 0.1uF 50V B D22-23 VT332900 DIODE 1SS355
DRX-730/NX-E700

C234 UR838100 C.EL 100uF 16V D24-25 VV833200 DIODE 1SS380

C235 US135100 C.CE.CHP 0.1uF 16V D26 VU993800 DIODE.ZENR MA8068-M 6.8V
C236-237 US062220 C.CE.CHP 220pF 50V B D27 VT332900 DIODE 1SS355
C240-241 US062220 C.CE.CHP 220pF 50V B D28 VU998800 DIODE.ZENR MAZ8220GHL 22.7V
C242 UR865470 C.EL 0.47uF 50V D29 VV833200 DIODE 1SS380
C243 US135100 C.CE.CHP 0.1uF 16V D30-34 VT332900 DIODE 1SS355
C244 UR847100 C.EL 10uF 25V D35 VU992600 DIODE.ZENR MA8051-M 5.1V
C245 WB165500 C.EL 0.33F 5.5V D36-40 VT332900 DIODE 1SS355
C247 US064100 C.CE.CHP 0.01uF 50V B IC1 X7378A00 IC NJM4565M(TE1)
✻ New Parts ✻ New Parts
59
 DRX-730/NX-E700

P.C.B. MAIN and P.C.B. SUB

Ref No. Part No. Description Markets Ref No. Part No. Description Markets
* IC2 X9799A00 IC R2A15908SP R115 WB785000 R.MTL.OXD 18 Ω 1W J
IC3 X7889A00 IC PCM1753DBQR R176 HV754100 R.CAR.FP 10 Ω 1/4W
IC4 X8235A00 IC LC72725KM GF R180 HV754100 R.CAR.FP 10 Ω 1/4W
IC5 X7974A00 IC KIA7809API-U/P R184 HV754100 R.CAR.FP 10 Ω 1/4W
IC6 X8705A00 IC KIA78M05F R185 V9199400 R.MTL.OXD 1.2K Ω 1W
* IC7 X9908A00 IC 74AHCT541PW TSSOP R187 HV753220 R.CAR.FP 2.2 Ω 1/4W
IC8 X2331A00 IC NJM4580E OP AMP R190 HV754100 R.CAR.FP 10 Ω 1/4W
IC9 X4153A00 IC KIA7812API R193 HV753680 R.CAR.FP 6.8 Ω 1/4W
* IC10 X9825A00 IC BD9778HFP R199 VP940200 R.MTL.OXD 47 Ω 1W
* IC11 YA013A00 IC.CPU R5F3640DNFA CPU (unwritten) R205 WB785000 R.MTL.OXD 18 Ω 1W J
IC12 X7651A00 IC BD9302FP-E2 R206 VP940200 R.MTL.OXD 47 Ω 1W
* IC13 X9563A00 IC MIC2005-0.5YM6 SOT23-6 R211 WB785000 R.MTL.OXD 18 Ω 1W J
* IC14 X9823A00 IC TDA8922BTH R320 VU224000 R.MTL.FLM 0.22 Ω 1W
* IC15 X9888A00 IC BA50DD0WHFP R325 VU224000 R.MTL.FLM 0.22 Ω 1W
IC16 XR680A00 IC TC7SH08FU(TE85L,JF R332 VU224000 R.MTL.FLM 0.22 Ω 1W
IC17 XS775A00 IC TC7SH04FU R372-373 VP940000 R.MTL.OXD 22 Ω 1W
IC20 XV892B00 IC TC74VHC74FT(EL,K) TE1 WD039300 TERM.SP 4P LQR2411-0001FM UCTAV
IC21 X2331A00 IC NJM4580E OP AMP TE1 WD039400 TERM.SP 4P LQR2411-0003FM KGFL
IC26 X2331A00 IC NJM4580E OP AMP U1 WH536900 CN.PHOTO.T 1P GP1FAV51TK0F
IC27 X7444A00 IC KIA78L05F-RTF/P XL1 WJ588000 RSNR.CRYS 4.332MHz GF
* IC28 YA171A00 IC TS3V340PWR PW GF XL2 VQ328900 RSNR.CRYS 32.768KHz
IC29 X8294A00 IC M24C02-WDW6TP XL3 WB440500 RSNR.CE CSTCE16M0V53-R0
PJ1 WG089100 JACK.PIN JACK 4P R/BE/G/Y WE807300 SHEET.RD 19x24
PJ2 WF342300 JACK.PIN MSP-241V2 WE774400 SCR.BND.HD 3x8 MFZN2B3
PJ3 V7046700 JACK.PIN 4P MSP-244V1-01NI
PN1-4 V9637500 PIN L=70 #18
Q1-2 VV556400 TR 2SC2412K Q,R,S
Q3-4 VZ725900 TR 2SD1938F S,T * WQ229000 P.C.B. SUB UC
Q6 VV556400 TR 2SC2412K Q,R,S * WQ229100 P.C.B. SUB TK
Q8 VV655700 TR.DGT DTC144EKA GF * WQ229200 P.C.B. SUB A
Q9 VZ725900 TR 2SD1938F S,T * WQ229300 P.C.B. SUB GFL
Q10 VV556400 TR 2SC2412K Q,R,S GF * WQ229400 P.C.B. SUB V
Q12 VZ725900 TR 2SD1938F S,T CB501 VG879900 CN.BS.PIN 2P
Q13 VV556400 TR 2SC2412K Q,R,S GF CB502-503 WN103000 CLIP.FUSE TP00351-31
Q15 VV655700 TR.DGT DTC144EKA GF CB801 WB832600 CN 6P TE
Q16 WC529500 TR KTA1504S Y GR RTK GF CB806 V5766700 CN 30P TE
Q18 VV655700 TR.DGT DTC144EKA GF * CB807 WQ092000 CN.USB 4P TE
Q19 VV556400 TR 2SC2412K Q,R,S GF C501 V5877700 C.MYLAR 0.22uF 250V
Q20-22 VZ725900 TR 2SD1938F S,T C502 WH036100 C.CE.SAFTY 2200pF 250V UCV
Q23-24 WC529500 TR KTA1504S Y GR RTK C502-503 WH035900 C.CE.SAFTY 1000pF 250V TKAGFL
Q25-27 VZ725900 TR 2SD1938F S,T C503 WH035900 C.CE.SAFTY 1000pF 250V TKAGFL
Q28-29 WC529500 TR KTA1504S Y GR RTK C504 WN826300 C.CE.SAFTY 0.01uF 250V
Q31-32 WC529500 TR KTA1504S Y GR RTK C507 V5877700 C.MYLAR 0.22uF 250V
Q36 VV556400 TR 2SC2412K Q,R,S C508 US063100 C.CE.CHP 1000pF 50V B
Q37-40 VV655700 TR.DGT DTC144EKA C510 WD969200 C.CE.CHP 0.1uF 50V K
Q41-42 VV655300 TR.DGT DTA144EKA * C511 WP573900 C.EL 560uF 200V UCV
Q43 VV655700 TR.DGT DTC144EKA * C511 WP574000 C.EL 150uF 400V TKAGFL
Q44 VV556400 TR 2SC2412K Q,R,S * C512 WP340600 C.EL 47uF 35V
DRX-730/NX-E700

Q45 VV655700 TR.DGT DTC144EKA C513 WJ322400 C.CE.M.CHP 0.01uF 250V UCV
Q46 VV556400 TR 2SC2412K Q,R,S C513 WJ322300 C.CE.M.CHP 1000pF 630V TKAGFL
Q47 VV655700 TR.DGT DTC144EKA C514 WJ322300 C.CE.M.CHP 1000pF 630V TKAGFL
Q48 WC529500 TR KTA1504S Y GR RTK C515 WH035900 C.CE.SAFTY 1000pF 250V
Q49 VP872600 TR 2SA1708 S,T C516-517 WK413800 C.CE.M.CHP 1000pF 250V
Q50 VV655700 TR.DGT DTC144EKA GF * C518-519 WQ081600 C.EL 2200uF 25V
Q51-54 VZ725900 TR 2SD1938F S,T C522 UR839100 C.EL 1000uF 16V
R16 HV754100 R.CAR.FP 10 Ω 1/4W C523 UR848100 C.EL 100uF 25V
R73-75 VY893200 R.MTL.OXD 12 Ω 1W C524 WH138300 C.EL 1000uF 25V
✻ New Parts ✻ New Parts
60
 DRX-730/NX-E700

P.C.B. SUB
Ref No. Part No. Description Markets Ref No. Part No. Description Markets
* C527 WN934600 C.EL 1500uF 25V IC503 WP388200 PHOT.CPL TLP781(D4-GR,F)
C528 WG348200 C.EL 33uF 100V IC505 X6770A00 IC NJM431U(TE1)
C529 VR169200 C.MYLAR 0.47uF 50V IC506 WP388200 PHOT.CPL TLP781(D4-GR,F)
C533 WD969200 C.CE.CHP 0.1uF 50V K IC801 X6386A00 IC M66003-0131FP
C538-539 VU838100 C.MYLAR.ML ECQ-V1H105JL3 JK801-802 WH204400 JACK.MNI MSJ-035-18A GR
C540 VZ243300 C.CE.CHP 0.22uF 16V Q501 WF412500 FET 2SK3683-01MR ST UCV
C541 WD969200 C.CE.CHP 0.1uF 50V K Q501 WF703300 FET 2SK3679-01MR ST TKAGFL
C542 US063220 C.CE.CHP 2200pF 50V B Q502 WC292100 TR KTC3199-Y-AT/P
C543 WD969200 C.CE.CHP 0.1uF 50V K Q801 VV556400 TR 2SC2412K Q,R,S
C544 VZ243300 C.CE.CHP 0.22uF 16V Q802-804 VV655700 TR.DGT DTC144EKA
C548 UR847330 C.EL 33uF 25V Q805 VV556400 TR 2SC2412K Q,R,S
C550 US063100 C.CE.CHP 1000pF 50V B Q806 VV556500 TR 2SA1037K Q,R,S
C551 US062100 C.CE.CHP 100pF 50V B Q807 VV556400 TR 2SC2412K Q,R,S
C801 US064100 C.CE.CHP 0.01uF 50V B * R521 WQ093000 R.WW 0.22 Ω 5W K UCV
C803 US135100 C.CE.CHP 0.1uF 16V R527 HV755180 R.CAR.FP 180 Ω 1/4W
C806 US044220 C.CE.CHP 0.022uF 25V B R531 V9199400 R.MTL.OXD 1.2K Ω 1W
C809 US044220 C.CE.CHP 0.022uF 25V B R542-547 VT267900 R.MTL.OXD 1.8K Ω 1W
C813-814 US135100 C.CE.CHP 0.1uF 16V * R567 WQ093000 R.WW 0.22 Ω 5W K UCV
C815 US064100 C.CE.CHP 0.01uF 50V B * R567 WP582800 R.WW 0.18 Ω 5W K TKAGFL
C816 US135100 C.CE.CHP 0.1uF 16V R570 V9199400 R.MTL.OXD 1.2K Ω 1W
C817 UM388330 C.EL 330uF 6.3V SW501 V5859300 RELAY DC DLS12D1-0(M)
C818 US135100 C.CE.CHP 0.1uF 16V SW801-806 WD483100 SW.TACT SKRGAAD010
C819 US062100 C.CE.CHP 100pF 50V B SW807 WD448700 SW.RT.ENC XREB12104PVB25FINB
C820-821 US065100 C.CE.CHP 0.1uF 50V B * SW808 WQ215400 SW.RT.ENC XREB121PVB20FINA1
C822-823 US063100 C.CE.CHP 1000pF 50V B * T501 X9804A00 TRANS.PWR UCV
C824-826 UM417220 C.EL 22uF 50V * T501 X9805A00 TRANS.PWR TKAGFL
C827 US135100 C.CE.CHP 0.1uF 16V * T502 YA210A00 TRANS.PWR UC
C828 UM407220 C.EL 22uF 25V * T502 YA211A00 TRANS.PWR TK
C829 UM388100 C.EL 100uF 10V * T502 YA212A00 TRANS.PWR A
C830-831 US063100 C.CE.CHP 1000pF 50V B * T502 YA213A00 TRANS.PWR GFL
C832 US061220 C.CE.CHP 22pF 50V B * T502 YA214A00 TRANS.PWR V
C833 US065100 C.CE.CHP 0.1uF 50V B TH501 WF544600 POSISTOR NTPAD5R1LDNB0 5.1 UCV
D501 VN953300 DIODE.BRG D5SBA60 5A 600V TH501 WF129000 POSISTOR NTPAA100LDNB0 10 TKAGFL
D502 VN478200 DIODE D1NL20U U801 WC746300 L.DTCT RPM7138-H9
D503 WJ459300 DIODE D1FK60-5063 UCV V801 WH034300 FL.DSPLY 16-BT-133GNK
D503 WJ151900 DIODE STTH110A TKAGFL V3747400 SPACER.FL T4x6x18
D504 VG442300 DIODE.ZENR MTZ J 22D 22V WE983600 SCR.BND.HD 3x8 MFZN2B3
D505 WN672400 DIODE.ZENR P6KE200A 200V TKAGFL WE774400 SCR.BND.HD 3x8 MFZN2B3
D506 WN672400 DIODE.ZENR P6KE200A 200V
D507 VN478200 DIODE D1NL20U
D508-509 VT332900 DIODE 1SS355
* D510-511 WQ080900 DIODE.SCHO STPS20150CFP 20A
D512 VT532500 DIODE 1SR154-400
D513 VR253700 DIODE.BRG S1NB20 1A 200V
* D514 WQ545500 DIODE.SCHO D5S9M
D515 VQ308300 DIODE D1NL40 TP 4083
* D516 WQ080900 DIODE.SCHO STPS20150CFP 20A
D517 VU172800 DIODE.ZENR UDZS12B TE-17 12V
DRX-730/NX-E700

D518-519 VU998700 DIODE.ZENR MA8220-M 22V

D521 VT532500 DIODE 1SR154-400
D801-804 VT332900 DIODE 1SS355
D809-810 VU758600 LED(gr) SLR-342MC
D811 VU993400 DIODE.ZENR MA8062-M 6.2V
D812 VT439400 LED(red) SLR-342VC3F
F501 WG410300 FUSE 4A 125V UCV
F501 KB000750 FUSE.MNI T2A 250V TKAGFL
* IC502 X9806A00 IC L6566BTR SW DENGEN
✻ New Parts ✻ New Parts
61
 A B C D E
DRX-730/NX-E700

• OVERALL ASS'Y

141
101
141

150 141

MAIN UNIT

FRONT PANEL UNIT

105
4
149
150

200

5
112 149

200-1
111
202 U, C, T, L, V models

141
6

204 203 202 K, A, G, F models

62
 DRX-730/NX-E700

Ref No. Part No. Description Remarks Markets

* 101 WP302500 TOP COVER GD
* 101 WP302700 TOP COVER BL
* 101 WP302600 TOP COVER SI, WH
* 105 WP305700 LID GD
* 105 WP305900 LID BL
* 105 WP305800 LID SI, WH
* 111 WP303100 KNOB D32 GD
* 111 WP303300 KNOB D32 BL
* 111 WP303200 KNOB D32 SI, WH
* 112 WP302800 KNOB D19 GD
* 112 WP303000 KNOB D19 BL
* 112 WP302900 KNOB D19 SI, WH
141 WE774100 BIND HEAD BONDING B-T. SCREW 3x8 MFZN2B3
149 WF266800 FLAT HEAD B-TIGHT SCREW 3x8 MFZN2B3
150 VY712800 PW HEAD B-TIGHT SCREW 3x8-8 MFNI33 GD, SI, WH
150 WE975300 PW HEAD B-TIGHT SCREW 3x8 MFZN2B3 BL

ACCESSORIES
* 200 WP507500 REMOTE CONTROL RRS4004-1006EM UCTKALV
* 200 WP507600 REMOTE CONTROL RRS4004-1007EM GF
200-1 AAX57560 BATTERY COVER 103RRS-141-07L
202 V6267000 INDOOR FM ANTENNA 1.4m 1pc UCTLV
202 VQ147100 INDOOR FM ANTENNA 1.4m 1pc KAGF
203 VQ307400 AM LOOP ANTENNA 1.2m 1pc
204 WG299500 VIDEO PIN CABLE 1P 1.5m YE 1pc
BATTERY R6,AA,UM-3 2pcs

SERVICE TOOL
AAX77610 RS232C CONVERSION ADAPTER with CABLE 9P

DRX-730/NX-E700

✻ New Parts
63
 A B C D E
DRX-730/NX-E700

• FRONT PANEL UNIT

1-116

1-117
1-116
1-115 1-103
1-110
2 1-117
1-116

1-109

1-11
1-108
3 1-12

1-111

4
1-104

1-115
1-102

1-103

1-101

64
 DRX-730/NX-E700

Ref No. Part No. Description Remarks Markets

* 1-11 WQ277200 FLEXIBLE FLAT CABLE 6P 90mm P=1.0
* 1-12 WQ277800 FLEXIBLE FLAT CABLE 30P 90mm P=1.0
* 1-101 WP300400 FRONT PANEL GD
* 1-101 WP300600 FRONT PANEL BL
* 1-101 WP300500 FRONT PANEL SI, WH
* 1-102 WP303500 SUB PANEL GD
* 1-102 WP303700 SUB PANEL BL
* 1-102 WP303600 SUB PANEL SI, WH
* 1-103 WP303800 SIDE PLATE GD, BL, SI
* 1-103 WP303900 SIDE PLATE WH
* 1-104 WP378300 WINDOW PANEL GD
* 1-104 WP306000 WINDOW PANEL BL, SI, WH
* 1-108 WP304500 BUTTON 2P SKIP/SEARCH GD
* 1-108 WP304700 BUTTON 2P SKIP/SEARCH BL
* 1-108 WP304600 BUTTON 2P SKIP/SEARCH SI, WH
* 1-109 WP304800 BUTTON STB STANDBY/ON GD
* 1-109 WP305000 BUTTON STB STANDBY/ON BL
* 1-109 WP304900 BUTTON STB STANDBY/ON SI, WH
* 1-110 WP305100 BUTTON EJ OPEN/CLOSE GD
* 1-110 WP305300 BUTTON EJ OPEN/CLOSE BL
* 1-110 WP305200 BUTTON EJ OPEN/CLOSE SI, WH
* 1-111 WP305400 BUTTON PS PLAY/STOP GD
* 1-111 WP305600 BUTTON PS PLAY/STOP BL
* 1-111 WP305500 BUTTON PS PLAY/STOP SI, WH
1-115 VQ368600 PUSH RIVET P3555-B
1-116 WE774800 BIND HEAD P-TIGHT SCREW 3x8 MFZN2W3
* 1-117 WQ488500 CUSHION 10x20x3

DRX-730/NX-E700

✻ New Parts
65
 A B C D E
DRX-730/NX-E700

• MAIN UNIT

2-31 2-33
2-34
2-121
2-121
2-36 2-122
2 2-35
2-5
2-32 2-22 2-124
2-102 2-124
2-123 2-38
2-6-1

2-124

3 2-1 (2)
2-123

2-124
2-11

2-6 2-12
DVD Mechanism Ass'y
4
2-2 (1)
2-121

2-121
2-121

5
2-1 (1)

2-115

2-121

2-121
2-103
2-103 2-124 2-124
2-121
2-121

66
 DRX-730/NX-E700

Ref No. Part No. Description Remarks Markets

* 2-1 WQ228200 P.C.B. ASS'Y MAIN UC
* 2-1 WQ228300 P.C.B. ASS'Y MAIN T
* 2-1 WQ228400 P.C.B. ASS'Y MAIN K
* 2-1 WQ228500 P.C.B. ASS'Y MAIN A
* 2-1 WQ228600 P.C.B. ASS'Y MAIN GF
* 2-1 WQ228700 P.C.B. ASS'Y MAIN L
* 2-1 WQ228800 P.C.B. ASS'Y MAIN V
* 2-2 WQ229000 P.C.B. ASS'Y SUB UC
* 2-2 WQ229100 P.C.B. ASS'Y SUB TK
* 2-2 WQ229200 P.C.B. ASS'Y SUB A
* 2-2 WQ229300 P.C.B. ASS'Y SUB GFL
* 2-2 WQ229400 P.C.B. ASS'Y SUB V
* 2-5 WQ967500 DVD MODULE P.C.B. DB-VPB801 REGION 1 UC
* 2-5 WQ968000 DVD MODULE P.C.B. DB-VPB801 REGION 6 T
* 2-5 WQ967700 DVD MODULE P.C.B. DB-VPB801 REGION 3 KLV
* 2-5 WQ967800 DVD MODULE P.C.B. DB-VPB801 REGION 4 A
* 2-5 WQ967600 DVD MODULE P.C.B. DB-VPB801 REGION 2 G
* 2-5 WQ967900 DVD MODULE P.C.B. DB-VPB801 REGION 5 F
* 2-6 WQ930300 DVD MECHANISM ASS'Y with CABLE
* 2-6-1 AAX90730 BELT LOADING 92P200015A
2-11 WB120500 POWER CABLE 2m UC
2-11 WB120600 POWER CABLE 2m T
2-11 WC753000 POWER CABLE 2m K
2-11 WC743700 POWER CABLE 2m A
2-11 WB212300 POWER CABLE 2m GFL
2-11 WC992700 POWER CABLE 2m V
2-12 V2438700 CORD STOPPER 10P1
2-22 WB424000 AM/FM TUNER ENG06709Q UCLV
2-22 WB877300 AM/FM TUNER FAE381-A07F T
2-22 WB877400 AM/FM TUNER FAE481-E07F K
2-22 WB424100 AM/FM TUNER ENG07711Q AGF
* 2-31 WQ277400 FLEXIBLE FLAT CABLE 13P 210mm P=1.0
* 2-32 WQ277500 FLEXIBLE FLAT CABLE 14P 90mm P=1.0 GF
* 2-33 WQ277600 FLEXIBLE FLAT CABLE 17P 230mm P=1.0
* 2-34 WQ662700 FLEXIBLE FLAT CABLE 27P 320mm P=1.0
* 2-35 WQ277900 FLEXIBLE FLAT CABLE 24P 330mm P=0.5
2-36 MF113120 FLEXIBLE FLAT CABLE 13P 120mm P=1.25
* 2-38 WQ433700 SHEET RADIATOR 24x25
* 2-102 WP301400 REAR PANEL UC
* 2-102 WP378200 REAR PANEL T
* 2-102 WP301900 REAR PANEL K
* 2-102 WP301500 REAR PANEL A
* 2-102 WP301600 REAR PANEL G
* 2-102 WQ185500 REAR PANEL F
* 2-102 WP301800 REAR PANEL L
DRX-730/NX-E700

* 2-102 WP301700 REAR PANEL V

2-103 V3688500 LEG D22/H8.2
* 2-115 WP306100 SHEET PSU
2-121 WF002600 PW HEAD B-TIGHT SCREW 3x8 MFZN2W3
2-122 WE774100 BIND HEAD BONDING B-T. SCREW 3x8 MFZN2B3
2-123 WE774400 BIND HEAD B-TIGHT SCREW 3x8 MFZN2B3
2-124 WF304200 BIND HEAD S-TIGHT SCREW 3x5 MFZN2B3

✻ New Parts
67
 A B C D E
DRX-730/NX-E700
NX-E700
1

• OVERALL ASS'Y
7 12
13

7-1

7-3
2
3
7-2 21

22

2 30
22

3
30

1-12
4

4
0.27mH TWEETER
L2

R1 C2

2.7ohms/5W 3.3uF/63V
8.2uF/63V
C1

INPUT WOOFER
L1

1.0mH

5 Ref No. Part No. Description Remarks Markets

1 WG237700 CABINET ASS'Y Black color GD, BL, SI
1 WM884000 CABINET ASS'Y White color WH
1-12 V9909600 HOLDER
2 WG237800 FRONT GRILLE ASS'Y Black color GD, BL, SI
2 WM884100 FRONT GRILLE ASS'Y White color WH
3 XW275B00 DRIVER TWEETER 2.5cm 5Ω JA05U3
4 XZ668D00 DRIVER WOOFER 11cm 6Ω JA1151
7 V9504600 NETWORK ASS'Y
7-1 V6055400 ELECTROLYTIC CAP 8.2uF 63V C1
6
7-2 V6367500 ELECTROLYTIC CAP 3.3uF 63V C2
7-3 V9507500 CEMENT RESISTOR 2.7 Ω 5W R1
12 V5361400 TERMINAL CAP S06E RED
13 V5361500 TERMINAL CAP S06E BLACK
21 WE963200 FLAT HEAD WOOD SCREW 3.5x20 MFZN2B3
22 WF824200 HEXAGON HEAD WOOD SCREW 4x25 MFZN2B3

ACCESSORY
30 V9826900 SPEAKER CABLE 4m 1pc
7

✻ New Parts
68
 DRX-730/NX-E700

Carbon Resistors
Value 1/4W Type Part No. 1/6W Type Part No. Value 1/4W Type Part No. 1/6W Type Part No.
1.0 Ω HJ35 3100 HF85 3100 11 kΩ HF45 7110 HF45 7110
1.8 Ω HJ35 3180 ✻ 12 kΩ HJ35 7120 HF85 7120
2.2 Ω HJ35 3220 HF85 3220 13 kΩ HF45 7130 HF45 7130
3.3 Ω HJ35 3330 HF85 3330 15 kΩ HF45 7150 HF45 7150
4.7 Ω HJ35 3470 HF85 3470 18 kΩ HF45 7180 HF45 7180
5.6 Ω HJ35 3560 HF85 3560 22 kΩ HF45 7220 HF45 7220
10 Ω HF45 4100 HF45 4100 24 kΩ HF45 7240 HF45 7240
15 Ω HJ35 4150 HF85 4150 27 kΩ HJ35 7270 HF85 7270
22 Ω HF45 4220 HF45 4220 30 kΩ HF45 7300 HF45 7300
27 Ω HJ35 4270 HF85 4270 33 kΩ HF45 7330 HF45 7330
33 Ω HF45 4330 HF45 4330 36 kΩ HF45 7360 HF45 7360
39 Ω HJ35 4470 HF85 4390 39 kΩ HF45 7390 HF45 7390
47 Ω HF45 4470 HF45 4470 47 kΩ HF45 7470 HF45 7470
56 Ω HF45 4560 HF45 4560 51 kΩ HF45 7510 HF45 7510
68 Ω HF45 4680 HF45 4680 56 kΩ HF45 7560 HF45 7560
75 Ω HF45 4750 HF45 4750 62 kΩ HF45 7620 HF45 7620
82 Ω HF45 4820 HF45 4820 68 kΩ HF45 7680 HF45 7680
91 Ω HF45 4910 HF45 4910 82 kΩ HF45 7820 HF45 7820
100 Ω HF45 5100 HF45 5100 91 kΩ HF45 7910 HF45 7910
110 Ω HJ35 5110 HF85 5110 100 kΩ HF45 8100 HF45 8100
120 Ω HF45 5120 HF45 5120 110 kΩ HF45 8110 HF45 8110
150 Ω HF45 5150 HF45 5150 120 kΩ HF45 8120 HF45 8120
160 Ω HJ35 5160 ✻ 150 kΩ HF45 8150 HF45 8150
180 Ω HF45 5180 HF45 5180 180 kΩ HF45 8180 HF45 8180
200 Ω HF45 5200 HF45 5200 220 kΩ HJ35 8220 HF85 8220
220 Ω HF45 5220 HF45 5220 270 kΩ HF45 8270 HF45 8270
270 Ω HF45 5270 HF45 5270 300 kΩ HF45 8300 HF45 8300
330 Ω HF45 5330 HF45 5330 330 kΩ HF45 8330 HF45 8330
390 Ω HF45 5390 HF45 5390 390 kΩ HJ35 8390 HF85 8390
430 Ω HF45 5430 HF45 5430 470 kΩ HF45 8470 HF45 8470
470 Ω HF45 5470 HF45 5470 560 kΩ HJ35 8560 HF85 8560
510 Ω HF45 5510 HF45 5510 680 kΩ HJ35 8680 HF85 8680
560 Ω HF45 5560 HF45 5560 820 kΩ HJ35 8820 HF85 8820
680 Ω HF45 5680 HF45 5680 1.0 MΩ HF45 9100 HF45 9100
820 Ω HF45 5820 HF45 5820 1.2 MΩ HJ35 9120 ✻
910 Ω HF45 5910 HF45 5910 1.5 MΩ HJ35 9150 HF85 9150
1.0 k HF45 6100 HF45 6100 1.8 MΩ HJ35 9180 HF85 9180
1.2 kΩ HF45 6120 HF45 6120 2.2 MΩ HJ35 9220 HF85 9220
1.5 kΩ HF45 6150 HF45 6150 3.3 MΩ HJ35 9330 HF85 9330
1.8 kΩ HF45 6180 HF45 6180 3.9 MΩ HJ35 9390 ✻
2.0 kΩ HJ35 6200 HF85 6200 4.7 MΩ HJ35 9470 HF85 9470
2.2 kΩ HF45 6220 HF45 6220
2.4 kΩ HJ35 6240 HF85 6240
2.7 kΩ HF45 6270 HF45 6270
1/4W Type
3.0 kΩ HF45 6300 HF45 6300
HF45
3.3 kΩ HF45 6330 HF45 6330
1/4W Type 1/6W Type
DRX-730/NX-E700

3.6 kΩ HJ35 6360 HF85 6360 HJ35 HF85

3.9 kΩ HF45 6390 HF45 6390 10mm
5mm
4.7 kΩ HF45 6470 HF45 6470
5.1 kΩ HF45 6510 HF45 6510
5.6 kΩ HF45 6560 HF45 6560
6.8 kΩ HF45 6680 HF45 6680
8.2 kΩ HF45 6820 HF45 6820
9.1 kΩ HF45 6910 HF45 6910
10 kΩ HF45 7100 HF45 7100
❊ : Not available
69
 A B C D E
DRX-730/NX-E700

1 ■ REMOTE CONTROL
SCHEMATIC DIAGRAM PANEL
U, C, T, K, A, L, V models
KEY No. 49 50 51

xx = 41 42 43 44 45 46 47 48

33 34 35 36 37 38 39 40

2 R1
25 26 17 18 29 30 31 32
2 ohms (1/4W)

17 18 19 20 21 22 23 24
C1 +
47μF R2
9 10 11 12 13 14 15 16
27 ohms
Q1
2SC3440-T112 1 2 3 4 5 6 7 8

20 19 18 17 16 15 14 13 12 11
VDD CARR D0 D1 D2 D3 D4 D5 D6 D7
3

IC1: M34283G2GP-W5/U1
Z-N0102-86214#1X

Not mount Vss E2 E1 XIN XOUT E0 G0 G1 G2 G3

C2
3.0V 1 2 3 4 5 T1 6 7 8 9 10
X1

4
4MHz

G, F models

70
 DRX-730/NX-E700

KEY NO. LAYOUT KEY CODE

Key Label (English) Custom Data Key Label (English) Custom Data
1 2 No. Upper Case Code Code No. Upper Case Code Code

3 4 5 6 1 STANDBY/ON 78 0F 27 TOP MENU/INFO. 7C B1

7 8 9 10
2 OPEN/CLOSE 78 00 28 78 8E
11 12 13 14
3 1 78 11 29 MENU 7C B2
15 16 17

18 19 20 4 2 78 12 30 78 9F

21 22 23 5 3 78 13 31 ENTER 78 C1
24 25 26
6 4 78 14 32 78 9E
27 28 29
7 5 78 15 33 SET UP 7C AC
30 31 32
8 6 78 16 34 78 8F
33 34 35
9 7 78 17 35 RETURN 7C B7
36 37 38
10 8 78 18 36 AUTO/MANUAL 78 B7
39 41
40 11 9 78 19 37 MEMORY 78 B2
42 43 44
12 0 78 10 38 VOLUME+ 78 1E
45 46 47
13 ZOOM 7C D7 39 BAND 78 B6
48 49 50 51
14 ON SCREEN 7C A6 40 TUNER 78 4B

15 AUDIO 7C AD 41 VOLUME- 78 1F

16 SUBTITLE 7C AA 42 DVD/USB 78 4A

17 ANGLE 7C AE 43 AUX/PORTABLE 78 49

18 PLAY MODE 7C BD 44 DOCK 78 D0

19 7C 85 45 SOUND 78 84

20 CLEAR 7C 9F 46 DIRECT 78 50

21 7C 86 47 MUTE 78 9C

22 7C 83 48 TIMER 78 A0

23 7C 87 49 SLEEP 78 4F

24 7C B9 50 DIMMER 78 BA

25 7C 82 51 DISPLAY 78 4E

26 7C BA
DRX-730/NX-E700

71
DRX-730/NX-E700