Scribd
Upload
616 views

3 CE133P Loads On Structures (Robles) 2 PDF

The document discusses loads on structures, including gravity loads like dead loads from structural members and live loads from temporary objects, as well as lateral loads from wind and earthquakes. It provides details on calculating and distributing different load types, such as specifying that dead and live loads are distributed uniformly across one-way slabs, but vary across two-way slabs based on distance from supports. Load conversions between common units are also presented.

Uploaded by

Lemuel Teope
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
616 views

3 CE133P Loads On Structures (Robles) 2 PDF

The document discusses loads on structures, including gravity loads like dead loads from structural members and live loads from temporary objects, as well as lateral loads from wind and earthquakes. It provides details on calculating and distributing different load types, such as specifying that dead and live loads are distributed uniformly across one-way slabs, but vary across two-way slabs based on distance from supports. Load conversions between common units are also presented.

Uploaded by

Lemuel Teope
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

REINFORCED CONCRETE DESIGN

LOADS ON STRUCTURES

ENGR. KEVIN PAOLO V. ROBLES, MSCE


Professor
LOADS ON STRUCTURES

Once the structural form has been determined, the


actual design begins with those elements that are
subjected to the primary loads the structure is
intended to carry, and proceeds in sequence to the
various supporting members until the foundation is
reached. In order to design a structure, it is therefore
necessary to first specify the loads that act on it

Thus, a building floor slab would be designed first, followed by the


supporting beams, columns, and last, the foundation footings.
.
DESIGN CODES

The NATIONAL BUILDING CODE, also known


as Presidential Decree No. 1096, is a
government policy covering technical
requirements in constructing or renovating
buildings and structures in the Philippines to
secure the life, health, property and welfare of
the Filipinos.
LOADS ON STRUCTURES GRAVITY LOADS

The vertical loads, due mainly to the occupancy, self-weight and


snow or rain, are commonly referred to as gravity loads.

Dead Loads. Dead loads consist of the weights of the various


structural members and the weights of any objects that are
permanently attached to the structure. The values for dead loads
are shown in NSCP Section 204, Tables 204-1 and 204-2 for
common material densities and minimum design dead loads for
common components.

Live Loads. Live Loads can vary both in their magnitude and
location. They may be caused by the weights of objects
temporarily placed on a structure, moving vehicles, or natural
forces. NSCP Section 204, Table 205-1 provides recommended
design live loads depending on the use of the space
LOADS ON STRUCTURES GRAVITY LOADS

Snow and Rain Loads. In some parts of the country, roof loading
due to snow or rain can be quite severe, and therefore protection
against possible failure is of primary concern.

Hydrostatic and Soil Pressure. When structures are used to retain


water, soil, or granular materials, the pressure developed by these
loadings becomes an important criterion for their design.

Impact Loads. When live loads are applied rapidly to a structure,


they cause larger stresses than those that would be produced if the
same loads would have been applied gradually. The dynamic effect
of the load that causes this increase in stress in the structure is
referred to as impact.
LOADS ON STRUCTURES LATERAL LOADS

The horizontal loads, induced mainly by wind and


earthquake are called lateral loads.

Wind Loads. When structures block the flow of wind, the


wind’s kinetic energy is converted into potential energy of
pressure, which causes a wind loading. The effect of wind on
a structure depends upon the density and velocity of the air,
the angle of incidence of the wind, the shape and stiffness of
the structure, and the roughness of its surface.

Earthquake Loads. Earthquakes produce loadings on a


structure through its interaction with the ground and its
response characteristics. These loadings result from the
structure’s distortion caused by the ground’s motion and the
lateral resistance of the structure.
LOADS DISTRIBUTION
ONE WAY SLAB
* ”s” is for shorter span and “l” is for longer span

(in lbs/ft or kN/m)


(in lbs/ft2 or kN/m2) ps
p

l
$"%! $"%!
2 (c) 2

l s $"%!
$"%! 2 $"%!
4 4
s

"!
2
s s
p "! (d)
2

p "!
2

"!
2

(b)
LOADS DISTRIBUTION
TWO WAY SLAB
LOADS DISTRIBUTION
TWO WAY SLAB
LOADS CONVERSION

9" 9"
2 3

s s

9" 9" 3 − <=


2 ; < = "/%
3 2

s/2 l-s s/2 l


l
LOADS DISTRIBUTION LATERAL LOADS

6m 2m

Monolithic Floor

• All slabs, t = 100 mm


• All beams, b = 250 mm ; h = 500 mm
• All columns, 300 mm x 300mm 5.0m

Superimposed Loads

• Floor Finish
• Ceramic tile ½ inch mortar
• Ceiling, wood furring
• Gypsum board ¼ inch thick

• Partition, wood, studs with gypsum Walls


board (h = 2.3m)
• weight = 3.0 kPa
• Live Load: Office • height = 3m

DEAD LOAD AND LIVE LOAD CALCULATION BASED ON NSCP 2015

You might also like