Scribd
Upload
143 views

Steel Member Deflection Check

The document provides design calculations for a steel runner. It specifies material properties including yield strength and allowable bending stress. It then calculates the load per meter, bending moment, required section modulus, and selects a steel hollow section. Calculations show the selected section meets requirements for section modulus, bending stress, and deflection.

Uploaded by

Prolay Manna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
143 views

Steel Member Deflection Check

The document provides design calculations for a steel runner. It specifies material properties including yield strength and allowable bending stress. It then calculates the load per meter, bending moment, required section modulus, and selects a steel hollow section. Calculations show the selected section meets requirements for section modulus, bending stress, and deflection.

Uploaded by

Prolay Manna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 12

DESIGN FOR STEEL RUNNER

fy = 310 N/mm2

σbt = 204.6 N/mm2

Pressure ( slab load ) = T/m2 Runner length = 2 m

C/C Distance b/w runner = m

S/Wt. of runner = kg/m

Load per meter run for each member = 0.7 T/m (FOR UDL)

Bending Moment = W*L2/8 = 0.280 T-m

Section Modulus(Z) = M / σbt = 13.6852394917 cm3

Assuming Section = SHS 60x40x4.5 from Sp 6_1

Section Moduli = Zxx = 18.42 cm3 > Zreqd Ok

Allowable Bending Stress = σbt = 204.6 N/mm2

Bending stress of section σbt = 152.01 N/mm2 < σallow Ok

Moment of Inertia = Ixx = 66.32 cm4

Young's Modulus = E= 2.00E+05 N/mm2

Deflection ( δ ) = (5WL3)/384EI

.= 10.995

Allowable Deflection ( δallow ) = 11.111 mm


HENCE OK
DESIGN FOR STEEL RUNNER

fy = 250 N/mm2

σbt = 165 N/mm2

Pressure ( slab load ) = 0.17


T/m2

C/C Distance b/w runner = 1 m

Load per meter run for each member = 0.170 T/m

Bending Moment = W*L2/2 = 0.340 T-m

Section Modulus(Z) = M / σbt = 20.606061 cm3

Assuming Section = RHS 122x61x4.5

Section Moduli = Zxx = 45.73 cm3

Allowable Bending Stress = σbt = 165 N/mm2

Bending stress of section σbt = 74.35 N/mm2

Moment of Inertia = Ixx = 278.95 cm4

Young's Modulus = E= 2.00E+05 N/mm2

Deflection ( δ ) = (WL3)/8EI

.= 6.094
Allowable Deflection ( δallow ) = 5.556 mm

REDESIGN
NNER

Runner length 2 m
=

(FOR UDL)

from Sp 6_1

> Zreqd Ok

< σallow Ok
DESIGN FOR STEEL RUNNER

fy = 250 N/mm2

σbt = 165 N/mm2

Wind Pressure = 0.107


T/m2

C/C Distance b/w purlin = 0.85 m

C/C Distance b/w main 2.29


member = m

No. of Point Loads, (n-1) = 6

Point load = 0.245 T

Bending Moment =

When n is odd = (n2-1)Pl/8n = 1.470

Section Modulus(Z) = M / σbt = 89.101818 cm3

Assuming Section = RHS 200x100x5

Section Moduli = Zxx = 145.93 cm3

Allowable Bending Stress = σbt = 165 N/mm2

Bending stress of section σbt = 100.75 N/mm2


Moment of Inertia = Ixx = 1459.25 cm4

Young's Modulus = E= 2E+05 N/mm2

Deflection ( δ ) = [(PL3)/192EI]*[n-(1/n)]*[3-0.5(1-(1/n2))]

.= 30.854

Allowable Deflection ( δallow ) = 19.444 mm

REDESIGN
NNER

Member 7 m
length, l =

n =7

> Zreqd Ok

< σallow Ok
-0.5(1-(1/n2))]
DESIGN FOR STEEL RUNNER

fy = 250 N/mm2

σbt = 165 N/mm2

Wind Pressure = 0.107


T/m2

C/C Distance b/w purlin = 0.825 m

C/C Distance b/w main 0.85


member = m

No. of Point Loads, (n-1) = 5

Point load = 0.075 T

Bending Moment =

When n is odd = (nPl)/8 = 0.284

Section Modulus(Z) = M / σbt = 17.215909 cm3

Assuming Section = RHS 200x100x5

Section Moduli = Zxx = 145.93 cm3

Allowable Bending Stress = σbt = 165 N/mm2

Bending stress of section σbt = 19.47 N/mm2


Moment of Inertia = Ixx = 278.94 cm4

Young's Modulus = E= 2.00E+05 N/mm2

Deflection ( δ ) = [(PL3)/192EI]*n*[3-0.5(1+(1/n2))]

.= 10.821

Allowable Deflection ( δallow ) = 14.028 mm

HENCE OK
NNER

Member 5.05 m
length, l =

n =6

> Zreqd Ok

< σallow Ok

You might also like