(https://www.eleccircuit.

com/)

LEARNING (HTTPS://WWW.ELECCIRCUIT.COM/LEARN-ELECTRONICS/)

ABOUT (HTTPS://WWW.ELECCIRCUIT.COM/ABOUT-US/)

CIRCUITS (HTTPS://WWW.ELECCIRCUIT.COM/SIMPLE-ELECTRONIC-

CIRCUITS/)

PROJECTS (HTTPS://WWW.ELECCIRCUIT.COM/EASY-ELECTRONIC-

PROJECTS/)
:: Home (https://www.eleccircuit.com/) » Contr

AMPLIFIERS (HTTPS://WWW.ELECCIRCUIT.COM/AMPLIFIER-CIRCUIT/)

POWER SUPPLIES (HTTPS://WWW.ELECCIRCUIT.COM/POWER-SUPPLY-

CIRCUIT/)

Blog

3000 watts Dimmer for SEARCH

HERE

Inductive Load
 Controls & Timers (https://www.eleccircuit.com/electronic-control/) -
Updated: January 17, 2020

This is the 3,000 watts Dimmer for inductor load

example: the Electric Fan, AC motor, Electric drill, etc. CATEGORIES
But most general dimmers are used for resistors load
Amplifiers &
only such as a lamp, soldering iron, heating coil, etc. Sounds
Why our project can do? (https://www.eleccir
cuit.com/amplifier/)

/
The normal dimmer cannot use for inductor load, Controls & Timers
because of the phase of current and voltage drop across (https://www.eleccir
cuit.com/electronic-
load not same, the current will slow than the voltage by control/)
90 degrees. (Theoretical maximum). If we trig the triac’s
Digitals &
gate lead at an angle of normal voltage, but current will Microcontrollers
lower than the holding current. (https://www.eleccir
cuit.com/digital/)

Inverters & DC
Table of Contents Converter
(https://www.eleccir
How inductive load dimmer works
cuit.com/inverter/)
How to builds
Lightings
Related Posts
(https://www.eleccir
GET UPDATE VIA EMAIL cuit.com/lighting/)

Meters & Detectors

(https://www.eleccir
How inductive load dimmer cuit.com/meter/)

works Power supply &

Chargers
(https://www.eleccir
Figure 1 is a Schematic Diagram of the 3000 watts
cuit.com/power-
inductive load dimmer. The Triac-Q2 is the high supply/)
sensitivity gate types. The C1, R5, and VR2 determined RF – Oscillator
the trigger angle. The VR1 is set at the lowest angle that (https://www.eleccir
cuit.com/rf-radio-
the Triac Q1 start conducts current.
frequency/)

Simple electronics
(https://www.eleccir
cuit.com/basic-
electronics/)

TOP
PROJECTS
CIRCUITS

/
(https://www.eleccircuit.com/wp- 0-30v 3A power
supply
content/uploads/2014/09/Schematic-Diagram-of-the-
(https://www.eleccir
3000-watts-Dimmer-for-Inductor-Load.jpg) cuit.com/cheap-
Figure 1 the schematic diagram of this project. adjustable-0-30v-
3a-laboratory-dc-
power-supply/)
Thus we must sure that adjust VR1 at load fewest works.
The capacitor C1 is charged from 0 volts continuously Inverter circuit
(https://www.eleccir
rise.
cuit.com/12v-to-
220v-inverter-
The Diac-D5 will conduct current when C1 charge to the
circuit-500w/)
breakdown voltage of D5.
LM317 Variable
The first pulse is sent to the gate lead of the Triac Q1 Supply
(https://www.eleccir
and the sparking voltage in R8 will be the trigger to Q1
cuit.com/lm317-
and Q2 conduct current. power-supply/)

The one resistance level is made of R4 + VR2/ /R3 + TDA2050 Power

Amplifier
VR1 will charge briefly the current from C1 ( the time is (https://www.eleccir
determined by (R5 + R6) C1). cuit.com/tda2050-
amplifier-stereo-
When through this delay range, the Q2 will begin 35w-75w/)

conducting current in the news cycle. Then, the pulse Simple Fish
from Q2 will trigger to Q1 until a current of Q1 lower to Shocker
(https://www.eleccir
zero.
cuit.com/electric-
fish-shocker-
The Triac Q2 will stop conducting current. Then, C1 will circuit/)
be charged by these devices (R4 + VR2/ /R3 + VR1).
12V to 5V
See Figure 1 again to clearly understanding.
converter
(https://www.eleccir
The Zener diode ZD1-ZD4 are used to the overvoltage cuit.com/12v-to-5v-
protection and makes the steady trigger voltage at all converter-step-
down-3a-regulator/)
time (positive-negative).
Pre amplifier with
Tone control
(https://www.eleccir
/
The diodes D1-D4 and R1, R2 will discharge the cuit.com/three-
circuits-of-preamp-
capacitors – C1, in While the time period is zero or the
tone-controls-by-
load current is zero. ne5532/)

The R7 and C2 are the damping network to protect 0-50V, 3A variable

supply
sparking current into this circuit. (https://www.eleccir
cuit.com/0-50v-3a-
variable-dc-power-
supply/)
How to builds
MOFET Amplifier
This project have many parts so should make the PCB circuit
as Figure 2 shows an actual-size of Single-sided Copper (https://www.eleccir
cuit.com/300-watt-
PCB layout. 1200-watt-mosfet-
amplifier-for-
professionals-only/)

36 Hobby
Electronic Projects
(https://www.eleccir
cuit.com/hobby-
electronic-projects/)
(https://www.eleccircuit.com/wp-
content/uploads/2014/09/the-PCB-layout-of-this-
projects.jpg) 5 LAST
POSTS
Figure 2 the PCB layout
Basic H-bridge
motor driver circuit
using bipolar
transistor
(https://www.eleccir
cuit.com/basic-h-
bridge-motor-
driver-by-bipolar-
(https://www.eleccircuit.com/wp- transistor/)
content/uploads/2014/09/the-components-layout1.jpg) Let’s try the 3
Figure 3 the components layout transistors Audio
Amplifier circuits
/
It’s like other projects we need completely assemble as (https://www.eleccir
cuit.com/lets-try-
Figure 3 show the components layout.
the-3-transistors-
audio-amplifier-
Note: circuits/)

Morning sun alarm

– This project is only ideal, I never tested it. thus if you
circuit using IC-
need to build them please be careful! and not for the 4011
beginner! (https://www.eleccir
cuit.com/morning-
– They are used with AC220V so safety first. alarm-with-sunlight-
using-ic-4011/)

– When a Triac Q2 works, it will get very hot, so we Transistor Crystal

always use a heat sink on it. Oscillator circuit
ideas
(https://www.eleccir
– The inductor L1, we can use the transformer toroidal
cuit.com/transistor-
core, No. TRB 24 x 15 x 10mm, and use the copper crystal-oscillator-
wires No. 19 to slowly wind up around core in the same circuit-ideas/)

way about 30 times. Simple Portable

Electronic Pulse
The parts you need Massager circuit
(https://www.eleccir
C1: 0.1uF 100V, Mylar
cuit.com/simple-
C2: 0.1uF 250V, Mylar handheld-
D1-D4: 1N4004, 600V,1A Diode electronic-pulse-
massager/)
F1: Fuse 6.3A
L1: 100uH___inductor
Q1: 4025Z5__transistor
Q2: 4006L4 or Triac;400V, 3A
R1, R2: 47K, 1W_ Resistors tolerance: 5%

0.25W Resistors, tolerance: 5%

R3: 150K
R4: 27K
R5: 10K
R6: 4.7K
/
R7: 220 ohms 1W Resistors tolerance: 5%
R8: 1K
ZD1-ZD4: 33V,1W__Zener diode
Other parts_____Heat sink,box,PCB, Fuse, Wires and
more.

Related Posts

(https://www.eleccircuit.com/ (https://www.eleccircuit.com/
super-ac-dimmer-using-ic- ac-lights-dimmer-circuit/)
555-triac/) Many AC Dimmer circuit ideas

AC dimmer for LED Bulbs using IC-

555 & TRIAC

(https://www.eleccircuit.com/
(https://www.eleccircuit.com/
power-battery-saver-circuit/)
pwm-dc-motor-controller-
Power Battery Saver Circuit
with-ne555-and-darlington-
transistors/)
555 PWM LED dimmer circuit
diagram