Support manual Service section TEL　027-251-2123

KANTO SEIKI FAX　027-290-1881

■Operating and stopping method ：
(1)Operating method：Press ①"POW"key until ⑧"RUN" lamp lights up to operate OILMATIC. ⑦Parameter LED
(2)Stopping method：Press1①"POW"key until ⑧"RUN" lamp turns off to stop OILMATIC. ⑥DATA　LED
(3)Operating and stopping by the external starting signal：When a No.14,19 terminals (for the exclusive use of external starting ) ⑧RUN　lamp ⑤UP　key
are received the external starting signal from the main machine,the OILMATIC operats and terminated OILMATIC stops.

■Setting and canceling key lock method　： RUN

(1)Setting key lock method：Press ⑤"UP"and ④"DOWN"keys simultaneously until "LED" on lower right ⑥"LED" UP
area blinks to deactivate all key operation excluding ①"POW" key. PARA DATA
(2)Canceling key lock method：Press ⑤"UP"and ④"DOWN"keys simultaneously until "LED" on lower right ⑥"LED" DOWN
area turns off to activate all key operaions. POW TMR PARA ENT
④DOWN　key
■Selecting temperature control method ：
(1)Changing base temperature follow up mode or constant mode：Press both ②"PARA"and ③"ENT" keys and also
either ⑤"UP" key or ④"DOWN" key to make a change. ①POW　key ②PARA　key ③ENT　key
The change of setting is completed upon release of the ②"PARA" and ③"ENT" keys.
The ⑥"LED",⑦"LED" corresponding under the diagram.
⑥Data LED ⑦Parameter ＬＥＤ Control mode
Ａ Ｅ Base temperature follow up mode . Setting Canceling
Ｃ Ｆ Constant mode. key lock key lock
DOWN
※A standard model controls inlet temperature.If you change it into outlet temperature control mode.Please attach the connector remove from
UP
+
inlet temperature sensor to outlet temperature sensor in control box and change the system parameters at once.
■Indication on the control panel and how to cope　： Simultaneous
Indication Cause Cope
ＡＬ１ RP(Reverse phase protective relay) or OL1(Pump moter protective device)is actuated
ＡＬ２ THP, ITS(Compressor ｔｅｍｐ. protective switch ) or GPS(Refrigeration pressure switch) is actuated.
ＡＬ３０ The Connection failure between the inverter PCB and the main PCB.
ＡＬ３１ The CPU mounting the inverter PCB unusual. Prease refer to an instruction manual 8-1.
ＡＬ３２ Over current of HIC（Inverter power IC)or heated up. PARA + ENT + or DOWN
UP
ＡＬ３３ Over current primary of inverter PCB.
Simultaneous
ＡＬ４ HTS1 or HTS2(Heater temp. protective switch) is actuated.
ＡＬ６１ The inlet temperature sensor is not connects.(The preparation sensor is not connects in case of PID control.)　　
ＡＬ６２ The outlet temperature sensor is not connects. (The liquid control sensor is not connects in case of PID control) Please confirm conection of the sensor. Follow up
⑥"LED"indicates ↑↓
ＡＬ６３ The base temperature sensor is not connects. ※In case of wire is brokｅｎ,please liquid temperature Constant
ＡＬ６４ The room temrerature sensor is not connects. exchange a new sensor.
Ｈ The control liquid temperature is higher than temperature the sum of the set
temperature and the maximum alarm.
Ｌ The control liquid temperature is lower than the set temperature minus Prease refer to an instruction manual 8-1. PARA + ENT
the minimum alarm temperature. Release
４５ The control liquid temperature is higher than 45 degree.
５ The control liquid temperature is lower than 5 degree.
ＦＩＬ Filter clogging. Prease refer to an instruction manual
and cleaning of air filter.
※About besides,please refer to "Service Manual"attached with Oilmatic.