3/24/2020 Control Systems - Construction of Bode Plots - Tutorialspoint

Control Systems - Construction of Bode Plots

In this chapter, let us understand in detail how to construct (draw) Bode plots.

Rules for Construction of Bode Plots

Follow these rules while constructing a Bode plot.

Represent the open loop transfer function in the standard time constant form.

Substitute, s
s =
= j
jωω in the above equation.

Find the corner frequencies and arrange them in ascending order.

Consider the starting frequency of the Bode plot as 1/10th of the minimum corner frequency or 0.1 rad/sec whichever is smaller value and draw
the Bode plot upto 10 times maximum corner frequency.
Draw the magnitude plots for each term and combine these plots properly.

Draw the phase plots for each term and combine these plots properly.

Note − The corner frequency is the frequency at which there is a change in the slope of the magnitude plot.

Example
Consider the open loop transfer function of a closed loop control system

10
10ss
G
G((s
s))H
H((s
s)) =
=
(
(ss+
+22)
)((s
s++5
5))

Let us convert this open loop transfer function into standard time constant form.

https://www.tutorialspoint.com/control_systems/control_systems_construction_bode_plots.htm 1/4
3/24/2020 Control Systems - Construction of Bode Plots - Tutorialspoint

10
10ss
G
G((s
s))H
H((s
s)) =
=
s
s s
s
2
2(( +
+11)
)55(
( +
+11)
)
2
2 5
5

s
s
⇒
⇒ G
G((s
s))H
H((s
s)) =
=
s
s s
s
(
(11+
+ )
)((1
1++ )
)
2
2 5
5

So, we can draw the Bode plot in semi log sheet using the rules mentioned earlier.

Stability Analysis using Bode Plots

From the Bode plots, we can say whether the control system is stable, marginally stable or unstable based on the values of these parameters.
Gain cross over frequency and phase cross over frequency
Gain margin and phase margin

Phase Cross over Frequency

The frequency at which the phase plot is having the phase of -1800 is known as phase cross over frequency. It is denoted by ω
ωppc
c
. The unit of

phase cross over frequency is rad/sec.

Gain Cross over Frequency

The frequency at which the magnitude plot is having the magnitude of zero dB is known as gain cross over frequency. It is denoted by ω
ωggc
c
. The

unit of gain cross over frequency is rad/sec.

The stability of the control system based on the relation between the phase cross over frequency and the gain cross over frequency is listed below.

If the phase cross over frequency ω

ωppc
c
is greater than the gain cross over frequency ω
ωggc
c
, then the control system is stable.

https://www.tutorialspoint.com/control_systems/control_systems_construction_bode_plots.htm 2/4
3/24/2020 Control Systems - Construction of Bode Plots - Tutorialspoint

If the phase cross over frequency ω

ωppc
c
is equal to the gain cross over frequency ω
ωggc
c
, then the control system is marginally stable.

If the phase cross over frequency ω

ωppc
c
is less than the gain cross over frequency ω
ωggc
c
, then the control system is unstable.

Gain Margin

Gain margin G
GMM is equal to negative of the magnitude in dB at phase cross over frequency.

1
1
G
GMM =
= 20
20 log
log(( )
) =
= 20
20llo
oggM
Mppc
c
M
Mppc
c

Where, M
Mppc
c
is the magnitude at phase cross over frequency. The unit of gain margin (GM) is dB.

Phase Margin

The formula for phase margin P

PMM is

0
0
P
PMM =
= 180
180 +
+ϕϕg
gcc

Where, ϕ
ϕggc
c
is the phase angle at gain cross over frequency. The unit of phase margin is degrees.

The stability of the control system based on the relation between gain margin and phase margin is listed below.

If both the gain margin G

GMM and the phase margin P
PMM are positive, then the control system is stable.

https://www.tutorialspoint.com/control_systems/control_systems_construction_bode_plots.htm 3/4
3/24/2020 Control Systems - Construction of Bode Plots - Tutorialspoint

If both the gain margin G

GMM and the phase margin P
PMM are equal to zero, then the control system is marginally stable.

If the gain margin G

GMM and / or the phase margin P
PMM are/is negative, then the control system is unstable.

https://www.tutorialspoint.com/control_systems/control_systems_construction_bode_plots.htm 4/4