Appendix Table

• inch-mm Conversion
• kgf – N Conversion
• kg – lb Conversion
• ˚C – ˚F Conversion
• Hardness Conversion Table Table 1
• Tolerance of Shaft Table 2
• Tolerance of Housing Bore Table 3
• Lubricating Greases Table 4
• inch-mm Conversion 1 inch = 25.4 mm
1 mm = 5/127 inch

inch > Calculate > mm

mm > Calculate > inch Clear

• kgf – N Conversion 1 kgf = 9.80665 N

1 N = 0.101972 kgf

kgf > Calculate > N

N > Calculate > kgf Clear

• kg – lb Conversion 1 kg = 2.204622 lb
1 lb = 0.45359 kg

kg > Calculate > lb

lb > Calculate > kg Clear

• ˚C – ˚F Conversion 1 ˚C = (9/5)C+32 ˚F
1 ˚F = (5/9)(F-32) ˚C

˚C > Calculate > ˚F

˚F > Calculate > ˚C Clear

Table 1 Hardness Conversion Table (1/3)

Nearly conversion for Rockwell C scale of Steel

Rockwell Brinell Rockwell

C scale Vickers Tungsten carbide A scale B scale Shore
(1471N) Standard ball
ball (588.4N) (980.7N)
68 940 – – 85.6 – 97
67 900 – – 85.0 – 95
66 865 – – 84.5 – 92

65 832 – (739) 83.9 – 91

64 800 – (722) 83.4 – 88
63 772 – (705) 82.8 – 87
62 746 – (688) 82.3 – 85
61 720 – (670) 81.8 – 83

60 697 – (654) 81.2 – 81

59 674 – (634) 80.7 – 80
58 653 – 615 80.1 – 78
57 633 – 595 79.6 – 76
56 613 – 577 79.0 – 75

55 595 – 560 78.5 – 74

54 577 – 543 78.0 – 72
53 560 – 525 77.4 – 71
52 544 (500) 512 76.8 – 69
51 528 (487) 496 76.3 – 68

Numbers with ( ) are for reference.

Table 1 Hardness Conversion Table (2/3)

Nearly conversion for Rockwell C scale of Steel

Rockwell Brinell Rockwell

C scale Vickers Tungsten carbide A scale B scale Shore
(1471N) Standard ball
ball (588.4N) (980.7N)
50 513 (475) 481 75.9 – 67
49 498 (464) 469 75.2 – 66
48 484 451 455 74.7 – 64
47 471 442 443 74.1 – 63
46 548 432 432 73.6 – 62

45 446 421 421 73.1 – 60

44 434 409 409 72.5 – 58
43 423 400 400 72.0 – 57
42 412 390 390 71.5 – 56
41 402 381 381 70.9 – 55

40 392 371 371 70.4 – 54

39 382 362 362 69.9 – 52
38 372 353 353 69.4 – 51
37 363 344 344 68.9 – 50
36 354 336 336 68.4 (109.0) 49

35 345 327 327 67.9 (108.5) 48

34 336 319 319 67.4 (108.0) 47
33 327 311 311 66.8 (107.5) 46
32 318 301 301 66.3 (107.0) 44
31 310 294 294 65.8 (106.0) 43

Numbers with ( ) are for reference.

Table 1 Hardness Conversion Table (3/3)

Nearly conversion for Rockwell C scale of Steel

Rockwell Brinell Rockwell

C scale Vickers Tungsten carbide A scale B scale Shore
(1471N) Standard ball
ball (588.4N) (980.7N)
30 302 286 286 65.3 (105.5) 42
29 294 279 279 64.7 (104.5) 41
28 286 271 271 64.3 (104.0) 41
27 279 264 264 63.8 (103.0) 40
26 272 258 258 63.3 (102.5) 38

25 266 253 253 62.8 (101.5) 38

24 260 247 247 62.4 (101.0) 37
23 254 243 243 62.0 100.0 36
22 248 237 237 61.5 99.0 35
21 243 231 231 61.0 98.5 35

20 238 226 226 60.5 97.8 34

(18) 230 219 219 – 96.7 33
(16) 222 212 212 – 95.5 32
(14) 213 203 203 – 93.9 31
(12) 204 194 194 – 92.3 29

(10) 196 187 187 – 90.7 28

( 8) 188 179 179 – 89.5 27
( 6) 180 171 171 – 87.1 26
( 4) 173 165 165 – 85.5 25
( 2) 166 158 158 – 83.5 24
( 0) 160 152 152 – 81.7 24

Numbers with ( ) are for reference.

Table 2 Tolerance of Shaft (1/4) Unit: µ m
Dimension a13 c12 d6 e6 e13 f5 f6 g5 g6
(mm)

Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low

3 6 - 270 - 450 - 70 - 190 - 30 - 38 - 20 - 28 - 20 - 200 -10 -15 - 10 - 18 - 4 - 9 - 4 - 12

6 10 - 280 - 500 - 80 - 230 - 40 - 49 - 25 - 34 - 25 - 245 -13 -19 - 13 - 22 - 5 -11 - 5 - 14
10 18 - 290 - 560 - 95 - 275 - 50 - 61 - 32 - 43 - 32 - 302 -16 -24 - 16 - 27 - 6 -14 - 6 - 17
18 30 - 300 - 630 -110 - 320 - 65 - 78 - 40 - 53 - 40 - 370 -20 -29 - 20 - 33 - 7 -16 - 7 - 20
30 40 - 310 - 700 -120 - 370 - 80 - 96 - 50 - 66 - 50 - 440 -25 -36 - 25 - 41 - 9 -20 - 9 - 25
40 50 - 320 - 710 -130 - 380
50 65 - 340 - 800 -140 - 440 -100 -119 - 60 - 79 - 60 - 520 -30 -43 - 30 - 49 -10 -23 -10 - 29
65 80 - 360 - 820 -150 - 450
80 100 - 380 - 920 -170 - 520 -120 -142 - 72 - 94 - 72 - 612 -36 -51 - 36 - 58 -12 -27 -12 - 34
100 120 - 410 - 950 -180 - 530
120 140 - 460 -1090 -200 - 600
140 160 - 520 -1150 -210 - 610 -145 -170 - 85 -110 - 85 - 715 -43 -61 - 43 - 68 -14 -32 -14 - 39
160 180 - 580 -1210 -230 - 630
180 200 - 660 -1380 -240 - 700
200 225 - 740 -1460 -260 - 720 -170 -199 -100 -129 -100 - 820 -50 -70 - 50 - 79 -15 -35 -15 - 44
225 250 - 820 -1540 -280 - 740
250 280 - 920 -1730 -300 - 820 -190 -222 -110 -142 -110 - 920 -56 -79 - 56 - 88 -17 -40 -17 - 49
280 315 -1050 -1860 -330 - 850
315 355 -1200 -2090 -360 - 930 -210 -246 -125 -161 -125 -1015 -62 -87 - 62 - 98 -18 -43 -18 - 54
355 400 -1350 -2240 -400 - 970
400 450 -1550 -2470 -440 -1070 -230 -270 -135 -175 -135 -1105 -68 -95 - 68 -108 -20 -47 -20 - 60
450 500 -1650 -2620 -480 -1110
500 560 – – – -260 -304 -145 -189 – – – – - 76 -120 – – -22 - 66
560 630
630 710 – – – -290 -340 -160 -210 – – – – - 80 -130 – – -24 - 74
710 800
800 900 – – – -320 -376 -170 -226 – – – – - 86 -142 – – -26 - 82
900 1000
1000 1120 – – – -350 -416 -195 -261 – – – – - 98 -164 – – -28 - 94
1120 1250
1250 1400 – – – -390 -468 -220 -298 – – – – -110 -188 – – -30 -108
1400 1600
Table 2 Tolerance of Shaft (2/4) Unit: µ m
Dimension h4 h5 h6 h7 h8 h9 h10 h11 h13 js4
(mm)

Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low

3 6 0 - 4 0 - 5 0 - 8 0 - 12 0 - 18 0 - 30 0 - 48 0 - 75 0 -180 + 2 - 2
6 10 0 - 4 0 - 6 0 - 9 0 - 15 0 - 22 0 - 36 0 - 58 0 - 90 0 -220 + 2 - 2
10 18 0 - 5 0 - 8 0 -11 0 - 18 0 - 27 0 - 43 0 - 70 0 -110 0 -270 + 2.5 - 2.5
18 30 0 - 6 0 - 9 0 -13 0 - 21 0 - 33 0 - 52 0 - 84 0 -130 0 -330 + 3 - 3
30 40 0 - 7 0 -11 0 -16 0 - 25 0 - 39 0 - 62 0 -100 0 -160 0 -390 + 3.5 - 3.5
40 50
50 65 0 - 8 0 -13 0 -19 0 - 30 0 - 46 0 - 74 0 -120 0 -190 0 -460 + 4 - 4
65 80
80 100 0 -10 0 -15 0 -22 0 - 35 0 - 54 0 - 87 0 -140 0 -220 0 -540 + 5 - 5
100 120
120 140
140 160 0 -12 0 -18 0 -25 0 - 40 0 - 63 0 -100 0 -160 0 -250 0 -630 + 6 - 6
160 180
180 200
200 225 0 -14 0 -20 0 -29 0 - 46 0 - 72 0 -115 0 -185 0 -290 0 -720 + 7 - 7
225 250
250 280 0 -16 0 -23 0 -32 0 - 52 0 - 81 0 -130 0 -210 0 -320 0 -810 + 8 - 8
280 315
315 355 0 -18 0 -25 0 -36 0 - 57 0 - 89 0 -140 0 -230 0 -360 0 -890 + 9 - 9
355 400
400 450 0 -20 0 -27 0 -40 0 - 63 0 - 97 0 -155 0 -250 0 -400 0 -970 +10 -10
450 500
500 560 – – – – 0 -44 0 - 70 0 -110 0 -175 0 -280 0 -440 – – – –
560 630
630 710 – – – – 0 -50 0 - 80 0 -125 0 -200 0 -320 0 -500 – – – –
710 800
800 900 – – – – 0 -56 0 - 90 0 -140 0 -230 0 -360 0 -560 – – – –
900 1000
1000 1120 – – – – 0 -66 0 -105 0 -165 0 -260 0 -420 0 -660 – – – –
1120 1250
1250 1400 – – – – 0 -78 0 -125 0 -195 0 -310 0 -500 0 -780 – – – –
1400 1600
Table 2 Tolerance of Shaft (3/4) Unit: µ m
Dimension j5 js5 j6 js6 j7 k4 k5 k6 m5
(mm)

Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low

3 6 +3 - 2 + 2.5 - 2.5 + 6 - 2 + 4 - 4 + 8 - 4 + 5 +1 + 6 +1 + 9 +1 + 9 + 4
6 10 +4 - 2 + 3 - 3 + 7 - 2 + 4.5 - 4.5 +10 - 5 + 5 +1 + 7 +1 +10 +1 +12 + 6
10 18 +5 - 3 + 4 - 4 + 8 - 3 + 5.5 - 5.5 +12 - 6 + 6 +1 + 9 +1 +12 +1 +15 + 7
18 30 +5 - 4 + 4.5 - 4.5 + 9 - 4 + 6.8 - 6.8 +13 - 8 + 8 +2 +11 +2 +15 +2 +17 + 8
30 40 +6 - 5 + 5.5 - 5.5 +11 - 5 + 8 - 8 +15 -10 + 9 +2 +13 +2 +18 +2 +20 + 9
40 50
50 65 +6 - 7 + 6.5 - 6.5 +12 - 7 + 9.5 - 9.5 +18 -12 +10 +2 +15 +2 +21 +2 +24 +11
65 80
80 100 +6 - 9 + 7.5 - 7.5 +13 - 9 +11 -11 +20 -15 +13 +3 +18 +3 +25 +3 +28 +13
100 120
120 140
140 160 +7 -11 + 9 - 9 +14 -11 +12.5 -12.5 +22 -18 +15 +3 +21 +3 +28 +3 +33 +15
160 180
180 200
200 225 +7 -13 +10 -10 +16 -13 +14.5 -14.5 +25 -21 +18 +4 +24 +4 +33 +4 +37 +17
225 250
250 280 +7 -16 +11.5 -11.5 +16 -16 +16 -16 +26 -26 +20 +4 +27 +4 +36 +4 +43 +20
280 315
315 355 +7 -18 +12.5 -12.5 +18 -18 +18 -18 +29 -28 +22 +4 +29 +4 +40 +4 +46 +21
355 400
400 450 +7 -20 +13.5 -13.5 +20 -20 +20 -20 +31 -32 +25 +5 +32 +5 +45 +5 +50 +23
450 500
500 560 – – – – – – +22 -22 – – – – – – +44 0 – –
560 630
630 710 – – – – – – +25 -25 – – – – – – +50 0 – –
710 800
800 900 – – – – – – +28 -28 – – – – – – +56 0 – –
900 1000
1000 1120 – – – – – – +33 -33 – – – – – – +66 0 – –
1120 1250
1250 1400 – – – – – – +39 -39 – – – – – – +78 0 – –
1400 1600
Table 2 Tolerance of Shaft (4/4) Unit: µ m
Dimension m6 n5 n6 p5 p6 r6 r7 Base Tolerance
(mm)

Over Incl. High Low High Low High Low High Low High Low High Low High Low IT2 IT3 IT5 IT7

3 6 + 12 + 4 +13 + 8 + 16 + 8 +17 +12 + 20 + 12 + 23 + 15 + 27 + 15 1.5 2.5 5 12

6 10 + 15 + 6 +16 +10 + 19 +10 +21 +15 + 24 + 15 + 28 + 19 + 34 + 19 1.5 2.5 6 15
10 18 + 18 + 7 +20 +12 + 23 +12 +26 +18 + 29 + 18 + 34 + 23 + 41 + 23 2 3 8 18
18 30 + 21 + 8 +24 +15 + 28 +15 +31 +22 + 35 + 22 + 41 + 28 + 49 + 28 2.5 4 9 21
30 40 + 25 + 9 +28 +17 + 33 +17 +37 +26 + 42 + 26 + 50 + 34 + 59 + 34 2.5 4 11 25
40 50
50 65 + 30 +11 +33 +20 + 39 +20 +45 +32 + 51 + 32 + 60 + 41 + 71 + 41 3 5 13 30
65 80 + 62 + 43 + 73 + 43
80 100 + 35 +13 +38 +23 + 45 +23 +52 +37 + 59 + 37 + 73 + 51 + 86 + 51 4 6 15 35
100 120 + 76 + 54 + 89 + 54
120 140 + 88 + 63 +103 + 63
140 160 + 40 +15 +45 +27 + 52 +27 +61 +43 + 68 + 43 + 90 + 65 +105 + 65 5 8 18 40
160 180 + 93 + 68 +108 + 68
180 200 +106 + 77 +123 + 77
200 225 + 46 +17 +51 +31 + 60 +31 +70 +50 + 79 + 50 +109 + 80 +126 + 80 7 10 20 46
225 250 +113 + 84 +130 + 84
250 280 + 52 +20 +57 +34 + 66 +34 +79 +56 + 88 + 56 +126 + 94 +146 + 94 8 12 23 52
280 315 +130 + 98 +150 + 98
315 355 + 57 +21 +62 +37 + 73 +37 +87 +62 + 98 + 62 +144 +108 +165 +108 9 13 25 57
355 400 +150 +114 +171 +114
400 450 + 63 +23 +67 +40 + 80 +40 +95 +68 +108 + 68 +166 +126 +189 +126 10 15 27 63
450 500 +172 +132 +195 +132
500 560 + 70 +26 – – + 88 +44 – – +122 + 78 +194 +150 +220 +150 – – – 70
560 630 +199 +155 +225 +155
630 710 + 80 +30 – – +100 +50 – – +138 + 88 +225 +175 +255 +175 – – – 80
710 800 +235 +185 +265 +185
800 900 + 90 +34 – – +112 +56 – – +156 +100 +266 +210 +300 +210 – – – 90
900 1000 +276 +220 +310 +220
1000 1120 +106 +40 – – +132 +66 – – +186 +120 +316 +250 +355 +250 – – – 105
1120 1250 +326 +260 +365 +260
1250 1400 +126 +48 – – +156 +78 – – +218 +140 +378 +300 +425 +300 – – – 125
1400 1600 +408 +330 +455 +330
Table 3 Tolerance of Housing Bore (1/3) Unit: µ m
Dimension E7 E10 E11 E12 F6 F7 F8 G6 G7 H6 H7
(mm)

Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low HighLow High Low
3 6 + 32 + 20 + 68 + 20 + 95 + 20 +140 + 20 + 18 + 10 + 22 + 10 + 28 + 10 + 12 + 4 + 16 + 4 + 8 0 + 12 0
6 10 + 40 + 25 + 83 + 25 +115 + 25 +175 + 25 + 22 + 13 + 28 + 13 + 35 + 13 + 14 + 5 + 20 + 5 + 9 0 + 15 0
10 18 + 50 + 32 +102 + 32 +142 + 32 +212 + 32 + 27 + 16 + 34 + 16 + 43 + 16 + 17 + 6 + 24 + 6 +11 0 + 18 0
18 30 + 61 + 40 +124 + 40 +170 + 40 +250 + 40 + 33 + 20 + 41 + 20 + 53 + 20 + 20 + 7 + 28 + 7 +13 0 + 21 0
30 40 + 75 + 50 +150 + 50 +210 + 50 +300 + 50 + 41 + 25 + 50 + 25 + 64 + 25 + 25 + 9 + 34 + 9 +16 0 + 25 0
40 50
50 65 + 90 + 60 +180 + 60 +250 + 60 +360 + 60 + 49 + 30 + 60 + 30 + 76 + 30 + 29 +10 + 40 +10 +19 0 + 30 0
65 80
80 100 +107 + 72 +212 + 72 +292 + 72 +422 + 72 + 58 + 36 + 71 + 36 + 90 + 36 + 34 +12 + 47 +12 +22 0 + 35 0
100 120
120 140
140 160 +125 + 85 +245 + 85 +335 + 85 +485 + 85 + 68 + 43 + 83 + 43 +106 + 43 + 39 +14 + 54 +14 +25 0 + 40 0
160 180
180 200
200 225 +146 +100 +285 +100 +390 +100 +560 +100 + 79 + 50 + 96 + 50 +122 + 50 + 44 +15 + 61 +15 +29 0 + 46 0
225 250
250 280 +146 +110 +320 +110 +430 +110 +630 +110 + 88 + 56 +108 + 56 +137 + 56 + 49 +17 + 69 +17 +32 0 + 52 0
280 315
315 355 +182 +125 +355 +125 +485 +125 +695 +125 + 98 + 62 +119 + 62 +151 + 62 + 54 +18 + 75 +18 +36 0 + 57 0
355 400
400 450 +198 +135 +385 +135 +535 +135 +765 +135 +108 + 68 +131 + 68 +165 + 68 + 60 +20 + 83 +20 +40 0 + 63 0
450 500
500 560 +215 +145 – – – – – – +120 + 76 +146 + 76 +186 + 76 + 66 +22 + 92 +22 +44 0 + 70 0
560 630
630 710 +240 +160 – – – – – – +130 + 80 +160 + 80 +205 + 80 + 74 +24 +104 +24 +50 0 + 80 0
710 800
800 900 +260 +170 – – – – – – +142 + 86 +176 + 86 +226 + 86 + 82 +26 +116 +26 +56 0 + 90 0
900 1000
1000 1120 +300 +195 – – – – – – +164 + 98 +203 + 98 +263 + 98 + 94 +28 +133 +28 +66 0 +105 0
1120 1250
1250 1400 +345 +220 – – – – – – +188 +110 +235 +110 +305 +110 +108 +30 +155 +30 +78 0 +125 0
1400 1600
1600 1800 +390 +240 – – – – – – +212 +120 +270 +120 +350 +120 +124 +32 +182 +32 +92 0 +150 0
1800 2000
Table 3 Tolerance of Housing Bore (2/3) Unit: µ m
Dimension H8 H9 H10 H11 H13 J6 Js6 J7 Js7 K5
(mm)

Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low
3 6 + 18 0 + 30 0 + 48 0 + 75 0 +180 0 + 5 -3 + 4 - 4 + 6 - 6 + 6 - 6 0 - 5
6 10 + 22 0 + 36 0 + 58 0 + 90 0 +220 0 + 5 -4 + 4.5 - 4.5 + 8 - 7 + 7.5 - 7.5 +1 - 5
10 18 + 27 0 + 43 0 + 70 0 +110 0 +270 0 + 6 -5 + 5.5 - 5.5 +10 - 8 + 9 - 9 +2 - 6
18 30 + 33 0 + 52 0 + 84 0 +130 0 +330 0 + 8 -5 + 6.5 - 6.5 +12 - 9 +10.5 -10.5 +1 - 8
30 40 + 39 0 + 62 0 +100 0 +160 0 +390 0 +10 -6 + 8 - 8 +14 -11 +12.5 -12.5 +2 - 9
40 50
50 65 + 46 0 + 74 0 +120 0 +190 0 +460 0 +13 -6 + 9.5 - 9.5 +18 -12 +15 -15 +3 -10
65 80
80 100 + 54 0 + 87 0 +140 0 +220 0 +540 0 +16 -6 +11 -11 +22 -13 +17.5 -17.5 +2 -13
100 120
120 140
140 160 + 63 0 +100 0 +160 0 +250 0 +630 0 +18 -7 +12.5 -12.5 +26 -14 +20 -20 +3 -15
160 180
180 200
200 225 + 72 0 +115 0 +185 0 +290 0 +720 0 +22 -7 +14.5 -14.5 +30 -16 +23 -23 +2 -18
225 250
250 280 + 81 0 +130 0 +210 0 +320 0 +810 0 +25 -7 +16 -16 +36 -16 +26 -26 +3 -20
280 315
315 355 + 89 0 +140 0 +230 0 +360 0 +890 0 +29 -7 +18 -18 +39 -18 +28.5 -28.5 +3 -22
355 400
400 450 + 97 0 +155 0 +250 0 +400 0 +970 0 +33 -7 +20 -20 +43 -20 +31.5 -31.5 +2 -25
450 500
500 560 +110 0 +175 0 +280 0 +440 0 – – – +22 -22 – – +35 -35 – –
560 630
630 710 +125 0 +200 0 +320 0 +500 0 – – – +25 -25 – – +40 -40 – –
710 800
800 900 +140 0 +230 0 +360 0 +560 0 – – – +28 -28 – – +45 -45 – –
900 1000
1000 1120 +165 0 +260 0 +420 0 +660 0 – – – +33 -33 – – +52.5 -52.5 – –
1120 1250
1250 1400 +195 0 +310 0 +500 0 +780 0 – – – +39 -39 – – +62.5 -62.5 – –
1400 1600
1600 1800 +230 0 +370 0 +600 0 +920 0 – – – +46 -46 – – +75 -75 – –
1800 2000
Table 3 Tolerance of Housing Bore (3/3) Unit: µ m
Dimension K6 K7 M6 M7 N6 N7 P6 P7 R6 R7
(mm)

Over Incl. High Low High Low High Low High Low High Low High Low High Low High Low High Low High Low
3 6 +2 - 6 + 3 - 9 - 1 - 9 0 - 12 - 5 - 13 - 4 - 16 - 9 - 17 - 8 - 20 - 12 - 20 - 11 - 23
6 10 +2 - 7 + 5 - 10 - 3 - 12 0 - 15 - 7 - 16 - 4 - 19 - 12 - 21 - 9 - 24 - 16 - 25 - 13 - 28
10 18 +2 - 9 + 6 - 12 - 4 - 15 0 - 18 - 9 - 20 - 5 - 23 - 15 - 26 - 11 - 29 - 20 - 31 - 16 - 34
18 30 +2 -11 + 6 - 15 - 4 - 17 0 - 21 -11 - 24 - 7 - 28 - 18 - 31 - 14 - 35 - 24 - 37 - 20 - 41
30 40 +3 -13 + 7 - 18 - 4 - 20 0 - 25 -12 - 28 - 8 - 33 - 21 - 37 - 17 - 42 - 29 - 45 - 25 - 50
40 50
50 65 +4 -15 + 9 - 21 - 5 - 24 0 - 30 -14 - 33 - 9 - 39 - 26 - 45 - 21 - 51 - 35 - 54 - 30 - 60
65 80 - 37 - 56 - 32 - 62
80 100 +4 -18 +10 - 25 - 6 - 28 0 - 35 -16 - 38 -10 - 45 - 30 - 52 - 24 - 59 - 44 - 66 - 38 - 73
100 120 - 47 - 69 - 41 - 76
120 140 - 56 - 81 - 48 - 88
140 160 +4 -21 +12 - 28 - 8 - 33 0 - 40 -20 - 45 -12 - 52 - 36 - 61 - 28 - 68 - 58 - 83 - 50 - 90
160 180 - 61 - 86 - 53 - 93
180 200 - 68 - 97 - 60 -106
200 225 +5 -24 +13 - 33 - 8 - 37 0 - 46 -22 - 51 -14 - 60 - 41 - 70 - 33 - 79 - 71 -100 - 63 -109
225 250 - 75 -104 - 67 -113
250 280 +5 -27 +16 - 36 - 9 - 41 0 - 52 -25 - 57 -14 - 66 - 47 - 79 - 36 - 88 - 85 -117 - 74 -126
280 315 - 89 -121 - 78 -130
315 355 +7 -29 +17 - 40 -10 - 46 0 - 57 -26 - 62 -16 - 73 - 51 - 87 - 41 - 98 - 97 -133 - 87 -144
355 400 -103 -139 - 93 -150
400 450 +8 -32 +18 - 45 -10 - 50 0 - 63 -27 - 67 -17 - 80 - 55 - 95 - 45 -108 -113 -153 -103 -166
450 500 -119 -159 -109 -172
500 560 0 -44 0 - 70 -26 - 70 -26 - 96 -44 - 88 -44 -114 - 78 -122 - 78 -148 -150 -194 -150 -220
560 630 -155 -199 -155 -225
630 710 0 -50 0 - 80 -30 - 80 -30 -110 -50 -100 -50 -130 - 88 -138 - 88 -168 -175 -225 -175 -255
710 800 -185 -235 -185 -265
800 900 0 -56 0 - 90 -34 - 90 -34 -124 -56 -112 -56 -146 -100 -156 -100 -190 -210 -266 -210 -300
900 1000 -220 -276 -220 -310
1000 1120 0 -66 0 -105 -40 -106 -40 -145 -66 -132 -66 -171 -120 -186 -120 -225 -250 -316 -250 -355
1120 1250 -260 -326 -260 -365
1250 1400 0 -78 0 -125 -48 -126 -48 -173 -78 -156 -78 -203 -140 -218 -140 -265 -300 -378 -300 -425
1400 1600 -330 -408 -330 -455
1600 1800 0 -92 0 -150 -58 -150 -58 -208 -92 -184 -92 -242 -170 -262 -170 -320 -370 -462 -370 -520
1800 2000 -400 -492 -400 -550
Table 4 Lubricating Greases (1/4)

Typical Lubricating Greases for Bearings

Recommended
Name of Grease Meets Military Dropping
Base Oil Thickener Penetration Operating
Grease Maker Spec. No. Point
Temperature
Alvania Equivalent 182ºC - 25ºC ~ 120ºC
Shell Mineral Oil Lithium 266
Grease 2 MIL-G-18709 360ºF - 15ºF ~ 250ºF
Alvania Equivalent 188ºC - 25ºC ~ 130ºC
Shell Mineral Oil Lithium 246
Grease 3 MIL-G-18709 370ºF - 15ºF ~ 260ºF
AeroShell 268ºC - 73ºC ~ 150ºC
Shell MIL-G-23827 Diester Oil Microgel 285
Grease 7 514ºF -100ºF ~ 300ºF
238ºC - 30ºC ~ 150ºC
Dolium R Shell Mineral Oil Polyurea 285
460ºF - 35ºF ~ 300ºF
Alvania EP 185ºC - 15ºC ~ 110ºC
Shell Mineral Oil Lithium 285
Grease 2 365ºF 5ºF ~ 230ºF
260ºC - 25ºC ~ 150ºC
Darina 2 Shell Mineral Oil Microgel 285
500ºF - 15ºF ~ 300ºF
193ºC - 54ºC ~ 120ºC
Beacon 325 Esso Standard MIL-G-3278 Diester Oil Lithium 280
380ºF - 65ºF ~ 250ºF

Remarks 1. When the grease is used at temperature near the high or low end of the recommended operating temperature,
please contact NACHI.
2. Generally Ester oil may give damage to polyacrylic rubber or ABS resin.
Please be careful, when you use grease with Ester base oil.
3. Do not mix different type of greases.
4. If sodium thickener grease is mixed with water, the grease become soft and may leak.
Table 4 Lubricating Greases (2/4)

Typical Lubricating Greases for Bearings

Properties
Name of
Color Water High Speed Grease Life Torpue at
Grease Noise
Resistance Rotation at High Temp. Low Temp.
Alvania
Grease 2
Light Yellow O O
Alvania
Grease 3
Light Yellow O O O
AeroShell
Grease 7
Light Brown O O O O
Dolium R Purple O O O
Alvania EP
Grease 2
Reddish Brown O
Light Yellowish
Darina 2
Brown O O
Beacon 325 Light Gray O O O
Remarks 1. When the grease is used at temperature near the high or low end of the recommended operating temperature,
please contact NACHI.
2. Generally Ester oil may give damage to polyacrylic rubber or ABS resin.
Please be careful, when you use grease with Ester base oil.
3. Do not mix different type of greases.
4. If sodium thickener grease is mixed with water, the grease become soft and may leak.
Table 4 Lubricating Greases (3/4)

Typical Lubricating Greases for Bearings

Recommended
Name of Grease Meets Military Dropping
Base Oil Thickener Penetration Operating
Grease Maker Spec. No. Point
Temperature
Lithium 300ºC - 30ºC ~ 150ºC
Temprex N3 Esso Standard Mineral Oil 235
Complex 572ºF - 35ºF ~ 300ºF
SH44M Toray Silicone 210ºC - 40ºC ~ 180ºC
MIL-L-15719 Silicone Oil Lithium 260
(DC44M) (Dow Corning) 410ºF - 40ºF ~ 350ºF
Polyol Ester Oil 191ºC - 40ºC ~ 150ºC
Multemp SRL Kyodo Yushi Lithium 245
+Diester Oil 375ºF - 40ºF ~ 300ºF
Diester Oil 190ºC - 55ºC ~ 130ºC
Multemp PS2 Kyodo Yushi Lithium 275
+Mineral Oil 374ºF - 67ºF ~ 260ºF
Synthetic 270ºC - 62ºC ~ 177ºC
Mobilgrease 28 Mobil Oil Hydrocarbon Oil Bentnite 270
518ºF - 79ºF ~ 350ºF
178ºC 0ºC ~ 125ºC
Mobilux 2 Mobil Oil Mineral Oil Lithium 270
352ºF 32ºF ~ 257ºF

Remarks 1. When the grease is used at temperature near the high or low end of the recommended operating temperature,
please contact NACHI.
2. Generally Ester oil may give damage to polyacrylic rubber or ABS resin.
Please be careful, when you use grease with Ester base oil.
3. Do not mix different type of greases.
4. If sodium thickener grease is mixed with water, the grease become soft and may leak.
Table 4 Lubricating Greases (4/4)

Typical Lubricating Greases for Bearings

Properties
Name of
Grease Color Water High Speed Grease Life Torpue at
Noise
Resistance Rotation at High Temp. Low Temp.

Temprex N3 Green O O O
SH44M
(DC44M)
Brown O O O
Multemp SRL Light Brown O O O O
Multemp PS2 White O O
Mobilgrease 28 Red O O
Mobilux 2 Brown O
Remarks 1. When the grease is used at temperature near the high or low end of the recommended operating temperature,
please contact NACHI.
2. Generally Ester oil may give damage to polyacrylic rubber or ABS resin.
Please be careful, when you use grease with Ester base oil.
3. Do not mix different type of greases.
4. If sodium thickener grease is mixed with water, the grease become soft and may leak.