Scribd
Upload
337 views

Installation Guide TagMaster RFID Tag Reader EN

This document provides guidance on positioning TagMaster long-range RFID readers to maximize performance for opening gates or barriers. It explains that readers should be mounted: 1) Approximately 2 meters before barriers at a height of 1.8 meters, oriented at a 30-45 degree angle toward the ground and 20-30 degrees toward the vehicle's path. 2) For headlight tags, at a height of 1.0-1.2 meters oriented at a 15-20 degree angle toward the ground and 30 degrees toward the vehicle's path. 3) Above entrances or gates at a height over 3 meters pointing toward the ground at a 45-60 degree angle.

Uploaded by

Rap Anthony
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
337 views

Installation Guide TagMaster RFID Tag Reader EN

This document provides guidance on positioning TagMaster long-range RFID readers to maximize performance for opening gates or barriers. It explains that readers should be mounted: 1) Approximately 2 meters before barriers at a height of 1.8 meters, oriented at a 30-45 degree angle toward the ground and 20-30 degrees toward the vehicle's path. 2) For headlight tags, at a height of 1.0-1.2 meters oriented at a 15-20 degree angle toward the ground and 30 degrees toward the vehicle's path. 3) Above entrances or gates at a height over 3 meters pointing toward the ground at a 45-60 degree angle.

Uploaded by

Rap Anthony
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

How to set up a

TagMaster Long
Range RFID Reader

Nr: 1120-004 04
About this guide
This guide gives a few examples of how to position a TagMaster RFID Reader, ensuring maximum performance, with the purpose
of opening a gate or a barrier. It will also give a brief insight of how a Long-Range RFID Reader works. Please note that Reader
performance will vary depending on the placement of the Reader, the Tag and technical specifications of the vehicle’s windshield. For
more information, see Installation Guide for TagMaster Windshield Tag (last section in this guide).

How a Long-Range RFID Reader works


Before explaining how to position the Long-Range RFID system, it is useful to know how the system works in general. The Reader
(antenna) emits energy/radio waves in a particular direction. When a passive Tag (IsoCard, Iso Combi Card, headlight or windshield
Tag) receives this energy, a small chip within the Tag is powered. When enough power is collected, the Tag transmits a signal. This
whole process takes a fraction of a second and repeats continuously as long as the Tag receives power from the antenna. The process
is directional, which means that the tag and reader must face each other. The more aligned the Reader and the Tag are, the better
performance (read range).

Flashlight and mirror


Think of a flashlight sending out light towards a mirror. The Reader is the flashlight and the Tag is the mirror. In a Long-Range RFID
solution, the mirror has to point in such a direction that the light is reflected back towards the flashlight.

When installing the Long-Range Reader, be aware of the energy bouncing off the Tag. Are the components aligned? Where will the
energy go? Will most of it bounce back towards the Reader, or will it bounce up into the sky?

The angle between Tag and Reader makes a big difference when installing vehicular Long-Range RFID solution. Try to direct the
Reader directly towards the point where most vehicles will have the Tag, normally the windshield or the headlight glass.

A low mounted reader might have difficulties reading windshield tags. A high mounted Reader might have trouble with headlight Tags.
headlight Tags work well with a low mounted reader, placed a bit higher than the approaching headlights. Windshield Tags require high
mounted readers.
How to position a Reader on the side of a barrier or
gate using windshield tags

How to position the reader:

Distance from barrier: Approximately 2m before barrier


if possible, on a pole or similar close to the road. The
identification zone will reach the vehicle earlier during the
approach and open the barrier a bit sooner to give the
vehicle a smother passage.

Height: approx.1,8m.

Orientation: 30° to 45° towards the ground,


20°- 30° towards the vehicle’s path.

Readers: XT Mini, XT-1, XT-5.

Tags: ISO Card, ISO Combi Card,


Windshield Tag.
How to position a Reader on the side of a barrier or gate using headlight tag

How to position the reader:

Distance from barrier: Approximately 2m before barrier


if possible, on a pole or similar close to the road. The
identification zone will reach the vehicle earlier during the
approach and open the barrier a bit sooner to give the
vehicle a smother passage.

Height: approx. 1,0 - 1,2 m.

Orientation: 15º to 20º towards the ground,


30° towards the vehicle’s path.

Orientation: 10º to 15º towards the ground,


30° towards the vehicle’s path.

Readers: XT Mini, XT-1, XT-5.

Tags: Headlight Tag, product no: 227000.


How to position a Reader above an entrance or gate

How to position the reader:

Distance from ground level to Reader: 2,5 – 3m.

Position: Centred above the entrance or gate.

Angle: Reader pointing towards the ground at an


45° - 60° angle.

Height: approx. > 3 m.

Readers: XT Mini, XT-1, XT-5.

Tags: ISO Card, ISO Combi Card,


Windshield Tag.
How to position Readers on both sides of a gate or barrier

How to position the reader:

Position: Place the reader on the right side of the gate


(right-hand traffic).

Angle: 30°- 45° towards the vehicle’s path.


Set up for centrally positioned Readers and road barriers

How to position the reader:

Position: Centrally positioned readers and road


barriers.
Position one reader in each direction..

Angle: 15°- 20° towards the vehicle’s path


Additional installation guides

Windshield Tag :
link : https://www.tagmaster.com/traffic-solutions/rfid/windshield-tag/

Headlight Tag :
link : https://www.tagmaster.com/traffic-solutions/rfid/headlight-tag/

Due to TagMaster’s continuous effort to develop the products in response to customer needs, the above specifications are subject to change.

You might also like