0% found this document useful (0 votes)
6K views

Vista-21IP Programming Guide PDF

Uploaded by

Gerardo Ramirez
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
6K views

Vista-21IP Programming Guide PDF

Uploaded by

Gerardo Ramirez
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 24

ADEMCO VISTA SERIES

VISTA-21iP / VISTA-21iPSIA
Security Systems

Programming Guide

K14488PRV1 7/08 Rev. B


TO ENTER PROGRAMMING MODE (using an alpha keypad connected to the control):
A. POWER UP, then press [✱] and [#] at the same time, within 50 seconds of powering up (this method must be used if ✱98
was used to exit program mode). OR
B. Initially, key: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0.
PROGRAMMING MODE COMMANDS
Task Command/Explanation
Go to a Data Field Press [∗ ∗] + [Field Number], followed by the required entry.
Entering Data When the desired field number appears, simply make the required entry. When the last entry
for a field is entered, the keypad beeps three times and automatically displays the next data
field in sequence. If the number of digits that you need to enter in a data field is less than the
maximum digits available (for example, the phone number fields *41, *42), enter the desired
data, then press [∗ ] to end the entry. The next data field number is displayed.
Review a Data Field Press [#] + [Field Number].
Data will be displayed for that field number. No changes will be accepted in this mode.
Deleting an Entry Press [∗ ∗] + [Field Number] + [∗ ∗]. (Applies only to fields ∗40 thru *46, *94, and pager fields)
Initialize Download ID Press ∗96. Initializes download ID and subscriber account number.
Reset Factory Defaults Press ∗97. Sets all data fields to original factory default values.
Zone Programming Press ∗56. Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800
RF transmitters.
Function Key Programming Press ∗57. Unlabeled keypad keys (known as ABCD keys) for special functions
Zone Programming Press ∗58. Same options as *56 mode, but with fewer prompts. Intended for those familiar
(Expert Mode) with this type of programming, otherwise *56 mode is recommended.
Output Device Mapping Press ∗79. Assign module addresses and map individual relays/powerline carrier devices
Output Programming Press ∗80. 4229 or 4204 Relay modules, Powerline Carrier devices, or on-board triggers
Zone List Programming Press ∗81. Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.
Alpha Programming Press ∗82. Zone alpha descriptors
IP/GSM Programming Press ∗29. For programming the IP/GSM options.
Exit Program Mode with Press ∗98. Exits programming mode and prevents re-entry by: Installer Code + 8 + 0 + 0.
installer code lockout To reenter programming mode, the system must be powered down, then powered up. Then
use method A above. See field *88 for other *98 Program mode lockout options.
Exit Program Mode Press ∗99. Exits programming mode and allows re-entry by: Installer Code + 8 + 0 + 0 or
method A above.
SPECIAL MESSAGES
OC = OPEN CIRCUIT (no communication between Keypad and Control).
EE or ENTRY ERROR = ERROR (invalid field number entered; re-enter valid field number).
After powering up, AC, dI (disabled) or Busy Standby and NOT READY will be displayed after approximately 4 seconds.
This will revert to a “Ready” message in approximately 1 minute, which allows PIRS, etc. to stabilize. You can bypass this
delay by pressing [#] + [0].
If E4 or E8 appears, more zones than the expansion units can handle have been programmed. The display will clear after
you correct the programming.
TABLE OF DEVICE ADDRESSES
This Device Uses Address Reports as †† Enabled By…
RF Receiver 00 100 *56 zone programming: input device type entry
AUI 1 01 101 automatic if AUI enable field *189 enabled for AUI 1
AUI 2 02 102 automatic if AUI enable field *189 enabled for AUI 2
AUI 3 05 105 automatic if AUI enable field *189 enabled for AUI 3
AUI 4 06 106 automatic if AUI enable field *189 enabled for AUI 4
Internal IP/GSM Device 03 103 automatic if installed and enabled in menu mode *29
4286 Voice Module 04 104 automatic if phone module access code field *28 enabled
Zone Expanders (4219/4229): *56 zone programming: input device type entry, then:
module 1 (for zones 09 - 16) 07 107 automatic if zone no. 9-16 entered as AW type or relay assigned
module 2 (for zones 17 - 24) 08 108 automatic if zone no. 17-24 entered as AW type or relay assigned
module 3 (for zones 25 - 32) 09 109 automatic if zone no. 25-32 entered as AW type or relay assigned
module 4 zones 33 - 40 10 110 automatic if zone no. 33-40 entered as AW type or relay assigned
module 5 zones 41 - 48 11 111 automatic if zone no. 41-48 entered as AW type or relay assigned
Relay Modules (4204): *79 output device programming: device address prompt:
module 1 12 112 entered at device address prompt
module 2 13 113 entered at device address prompt
module 3 14 114 entered at device address prompt
module 4 15 115 entered at device address prompt
Keypads: data field programming as listed below:
keypad 1 16 n/a always enabled, all sounds enabled.
keypad 2 17 n/a data field *190
keypad 3 18 n/a data field *191
keypad 4 19 n/a data field *192
keypad 5 20 n/a data field *193
keypad 6 21 n/a data field *194
keypad 7 22 n/a data field *195
keypad 8 23 n/a data field *196
5800TM Module 28 n/a automatic
†† Addressable devices are identified by “1” plus the device address when reporting. Enter report code for zone 91 to enable addressable device
reporting (default = reports enabled). See field *199 for addressable device (ECP) 3-digit/2-digit identification keypad display options.

–2–
PROGRAMMING FORM
Entries apply to the ADEMCO VISTA-21iP/VISTA-21iPSIA controls, except where noted, certain fields have special settings when used with the
VISTA-21iPSIA (indicated by V21iPSIA with heavy borders and reverse type throughout for easy identification).
Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.
SIA Guidelines: Notes in certain fields give instructions for programming the VISTA-21iP for False Alarm Reduction.
IMPORTANT! Make sure the Real-Time Clock is set before the end of the installation (see page 16 for procedure).

∗20 Installer Code [4112] | | | ∗36 Entry Delay #2 [30,30] | |


4 digits, 0–9 See *35 Entry Delay 1 for entries. Part. 1 Part. 2

∗21 Quick Arm Enable [0,0] ∗37 Audible Exit Warning [1,1]
0 = no; 1 = yes Part. 1 Part.2 0 = no; 1 = yes (SIA Guidelines: must be enabled) Part. 1 Part. 2

∗22 RF Jam Option [0] V21iPSIA: Feature always enabled; field does not exist.

0 = no RF Jam detection; 1 = send RF Jam report


UL: must be 1 if wireless devices are used ∗38 Confirmation Of Arming Ding [0,0]
0 = no; 1 = yes (wired keypads and RF) Part. 1 Part. 2
∗23 Quick (Forced) Bypass [0,0] 2 = yes, RF only (except 5827/5827BD)
0 = no quick bypass UL: must be “0” UL: must be “1” for UL Commercial Burglar Alarm inst.
Part. 1 Part. 2
1 = allow quick bypass (code + [6] + [#] )
∗39 Power Up In Previous State [1]
∗24 RF House ID Code [00,00,00] | | | 0 = no, always power up disarmed; 1 = yes, power up in previous state
00 = disable all wireless keypad usage Part. 1 Part. 2 Common UL: must be “1” SIA Guidelines: must be “1”
01–31 = using 5827, 5827BD or 5804BD keypad
V21iPSIA: Feature must be enabled (enter 1).
∗26 Chime By Zone [0]
0 = no; 1 = yes (list chime zones on zone list 3 using *81 Menu mode) DIALER PROGRAMMING (✱40 – ✱42)
Do not fill unused spaces. Enter 0–9; #+11 for '✱'; #+12 for '#'; #+13 for a 2-
∗27 Powerline Carrier Device (X–10) [0] second pause. If fewer than the maximum digits entered, exit the field by
pressing [✶]. The next data field number is displayed.
House Code
0 = A; 1 = B; 2 = C; 3 = D; 4 = E; 5 = F; 6 = G; 7 = H; 8 = I; 9 = J; ∗40 PABX Access Code or | | | | |
#10 = K; #11 = L; #12 = M; #13 = N; #14 = O; #15 = P
UL: not for fire or UL installations Call Waiting Disable Enter up to 6 digits. To clear entries,
press ✱40✱. If call waiting is used, enter call waiting disable digits “∗
∗28 Access Code For Phone Module [00] | (#+11) 70” plus “# + 13” (pause).
NOTES: 1. The call waiting disable feature cannot be used on a PABX line.
00 = disable; (Partition 1 only) 2. Using Call Waiting Disable on a non-call waiting line will
1st digit: enter 1–9; 2nd digit: enter # + 11 for "✱", or # + 12 for "#". prevent successful communication to the central station.
UL: must be “00” for UL Commercial Burg. installations
V21iPSIA: If call waiting is used, enter call waiting disable digits as
∗29 Menu Mode for IP/GSM Enable described above, and also set Call Waiting Disable option in field *91.
This is a Menu Mode command, not a data field, for programming IP/GSM
options. See respective section later in this document. ∗41 Primary Phone No.
∗31 Single Alarm Sounding Per Zone [0]
| | | | | | | | | | | | | | | | | | |

0 = unlimited sounding (bell output); 1 = one alarm sounding per zone ∗42 Secondary Phone No.
V21iPSIA: If “0” selected, “alarm sounding per zone” will be the same | | | | | | | | | | | | | | | | | | |
as the “number of reports in armed period” set in field *93 (1 if one
Enter up to 20 digits. To clear entries, press ✱41✱ or ✱42✱ respectively.
report, 2 if 2 reports, unlimited for zones in zone list 7).
NOTE: For fields *43 thru *46: Enter 0–9; #+11 for B; #+12 for C; #+13 for D;
#+14 for E; #+15 for F. Enter [✱] as the fourth digit if a 3-digit account number
∗32 Fire Alarm Sounder Timeout [0] (for 3+1 dialer reporting format) is used. Enter 0 as the first digit of a 4-digit
0 = sound stops at timeout; 1 = no timeout UL: must be “1” for fire install. account number for Nos. 0000-0999. Exit field by pressing ✱ if only 3 digits are
used. E.g., For Acct. B234, enter: #+11 + 2 + 3 + 4
∗33 Alarm Sounder (Bell) Timeout [1] ∗43 Partition 1 Primary Acct. No.
0 = none; 1 = 4 min; 2 = 8 min; 3 =12 min; 4 = 16 min;
UL: For residential fire alarm installation, must be set for a | | | / | | | | | [FFFFFFFFFF] Enter 4 or 10 digits, as
minimum of 4 min (option 1); for UL Commercial Burglary chosen in *48 Report Format. See box above. To clear entries, press *43*.
installations, must be minimum 16 min (option 4)
∗44 Part. 1 Secondary Acct. No. (see field *43 for entries)
∗34 Exit Delay [60,60] | | | | | / | | | | | [FFFFFFFFFF] To clear, press *44*.
00 - 96 = 0 - 96 secs; 97 = 120 secs Part. 1 Part. 2
SIA Guidelines: minimum exit delay is 45 seconds ∗45 Partition 2 Primary Acct. No. (see field *43 for entries)
V21iPSIA: 45 - 96 = 45 - 96 secs; 97 = 120 secs | | | / | | | | | [FFFFFFFFFF] To clear, press *45*.
NOTE: Entries less than 45 will result in a 45-second delay.
∗46 Partition 2 Secondary Acct. No. (see field *43 for entries)
UL: see inst. instr. for requirements. Common zones use part. 1 delay.
| | | / | | | | | [FFFFFFFFFF] To clear, press *46*.
∗35 Entry Delay #1 [30,30] | |
Common zones use same delay as partition 1. Part. 1 Part. 2
∗47 Phone System Select [1]
00 - 96 = 0 - 96 seconds; 97 = 120 secs; 98 = 180 secs; 99 = 240 secs If Cent. Sta. is not on a WATS line: 0=Pulse Dial; 1=Tone Dial;
SIA Guidelines: minimum entry delay is 30 seconds if Cent. Sta. is on a WATS line: 2 = Pulse Dial ; 3 = Tone Dial
V21iPSIA: ∗48 Report Format [77]
30-96 = 30 - 96 secs; 97 = 120 secs; 98 = 180 secs; 99 = 240 secs
0 = 3+1, 4+1 ADEMCO L/S STANDARD primary secondary
NOTE: Entries less than 30 will result in a 30-second delay.
1 = 3+1, 4+1 RADIONICS STANDARD; 2 = 4+2 ADEMCO L/S STAND.
3 = 4+2 RADIONICS STANDARD
For UL Residential Burglary Alarm installations, must be set for a
5 = 10-digit ADEMCO CONTACT ID® REPORTING
maximum of 30 seconds; entry delay plus dial delay should not
6 = 4+2 ADEMCO EXPRESS
exceed 1 min. For UL Commercial Burglar Alarm, total entry delay
7 = 4-digit ADEMCO CONTACT ID® REPORTING
may not exceed 45 seconds.
8 = 3+1, 4+1 ADEMCO L/S EXP.; 9 = 3+1, 4+1 RADIONICS EXP.

–3–
∗49 Split/Dual Reporting [0] ∗66 Arm Away/Stay Rpt Code
0 = Standard/backup reporting only (all to primary) [0,0,0,0,0,0]
Primary Phone No. 2nd Phone No.
Away Stay Away Stay Away Stay
1 = Alarms, Restore, Cancel Others
2 = All except Open/Close, Test Open/Close, Test Part. 1 Part. 2 Common
3 = Alarms, Restore, Cancel All ∗67 RF Trans. Low Bat Report Code [00] |
4 = All except Open/Close, Test All
5 = All All UL: must be enabled if wireless devices are used

∗50 Burglary Dialer Delay [2,0] ∗68 Cancel Report Code [00] |
Delay Time: Delay Time V21iPSIA V21iPSIA: [10] Report enabled.
0 = no delay UL: must be “0” Delay Disable
1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds ∗69 Recent Closing Report Code [11] |
SIA Guidelines: delay must be minimum of 15 seconds
V21iPSIA: V21iPSIA:Always enabled.
Delay Time: 1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds Field does not apply to other controls.
Delay Disable:
RESTORE REPORT CODES (✱70 – ✱76)
0 = use delay set in entry 1
1 = dial delay disabled for zones listed in zone list 6 (use zone list 6
to enter those zones that require dial delay to be disabled;
these zones ignore the setting in entry 1)
∗70 Alarm Restore Rpt Code [0]
UL: Dial delay plus entry delay must not exceed one minute; use zone
list 6 to disable dial delay from appropriate zones, if necessary. ∗71 Trouble Restore Rpt Code [00] |

∗53 SESCOA/Radionics Select [0]


∗72 Bypass Restore Rpt Code [00] |

0 = Radionics (0-9, B-F); enter “0” for all non-SESCOA formats


1 = SESCOA (0-9 only reporting)
∗73 AC Restore Rpt Code [00] |

∗54 Dynamic Signaling Delay [0] ∗74 Low Bat Restore Rpt Code [00] |
Select delay from 0 to 225 secs, in 15-sec increments.
0 = no delay (both signals sent); 1 = 15 secs; 2 = 30 secs, etc. ∗75 RF Trans. Lo Bat Rst Rpt Code [00] |
NOTE: If ∗55 is set to “0,” use min. 30 sec to avoid redundant IP UL: must be enabled if wireless devices are used
report. However, this value may need to be adjusted (ex. 45 secs)
depending on the reporting environment. ∗76 Test Restore Rpt Code [00] |
For UL Burglar Alarm installations with Line Security, must be “0”

∗55 Dynamic Signaling Priority [0]


OUTPUT AND SYSTEM SETUP (✱77 – ✱93)
0 = Primary Dialer first; 1 = IP/GSM module first. ∗77 Daylight Savings Time [3][11] |
For UL Commercial Burglary installations that use a DACT and
IP/GSM, this field must be “0”.
Start/End Month
0 = Disabled
1-12 = January-September (1 = Jan, 2 = Feb, etc)
∗56, ∗57, ∗58 Menu Modes #+10 = October; #+11 = November; #+12 = December
These are Menu Mode commands, not data fields, for Zone Programming,
Function Key Programming, and Expert Mode Zone Programming respectively. ∗78 Daylight Savings Time [2][1] |
See page 2 and respective sections later in this document.
Start/End Weekend
TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (∗ ∗59 thru 0 = disabled; 1 = first; 2 = second; 3 = third; 4 = fourth;
∗68, *70 thru ∗76, and ∗89): 5 = last; 6 = next to last; 7 = third to last
For 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, #+10 for
0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F.
∗79, *80, *81, *82 Menu Modes
A 0 (not #+10) in the first box will disable a report. A 0 (not #+10) in the These are Menu Mode commands, not data fields, for Output Device Mapping,
second box will result in automatic advance to the next field. Output Programming, Zone List Programming, and Alpha Programming
For Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) respectively. See page 2 and their respective sections in the Installation and
for 1–9, 0, or B–F, as described above. Setup Guide for procedures.
A 0 (not #+10) in the second box will eliminate the expanded message for
that report. A 0 (not #+10) in both boxes will disable the report. ∗84 Auto Stay Arm [3]
For Ademco Contact ID® Reporting: Enter any digit (other than 0) in the first
0 = no; 1 = partition 1 only; 2 = partition 2 only; 3 = both partitions
box, to enable zone to report (entries in the second boxes are ignored).
A 0 (not #+10) in the first box disables the report. ∗85 Cross Zone Timer [0]
UL: see installation instructions for requirements
This option not for use in UL installations.
SYSTEM STATUS REPORT CODES (✱59–✱ 68) (assign cross zones on zone list 4, using *81 Menu mode)
0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min
∗59 Exit Error Alarm Report Code [0] 1 = 30 seconds 7 = 3 min #+13 = 10 min
2 = 45 seconds 8 = 4 min #+14 = 12 min
See above for entries. V21iPSIA: [1] Always enabled. 3 = 60 seconds 9 = 5 min #+15 = 15 min
4 = 90 seconds #+10 = 6 min
∗60 Trouble Report Code [00] | 5 = 2 minutes #+11 = 7 min
NOTE: Cross zoning takes effect only after Exit Delay expires.
∗61 Bypass Report Code [00] |
∗86 Cancel Verify Keypad Display [1]
∗62 AC Loss Report Code [00] | 0 = no “alarm canceled” display
1 = display “Alarm Canceled” when system is disarmed after an alarm
∗63 Low Bat Report Code [00] | has occurred. (To clear the “ALARM CANCELED” display, the
user must enter the security code + OFF again.)

∗64 Test Report Code [00] | ∗87 Misc. Fault Delay Time [0]
Use Scheduling mode to set periodic test reports, or use the following (used with Configurable Zone Types “digit 6”)
key commands: 0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min
installer code +[#] + [0] + 0 = test report sent every 24 hours 1 = 30 seconds 7 = 3 min #+13 = 10 min
installer code +[#] + [0] + 1 = test report sent once per week 2 = 45 seconds 8 = 4 min #+14 = 12 min
installer code +[#] + [0] + 2 = test report sent every 28 day 3 = 60 seconds 9 = 5 min #+15 = 15 min
Each mode sets schedule 32 to the stated repeat option; first test report 4 = 90 seconds #+10 = 6 min
sent 12 hours after command. 5 = 2 minutes #+11 = 7 min
∗65 Open Report Code [0,0,0] UL: may only be used on non-burglar alarm/ non-fire alarm zones
when used in fire and/or UL burglar alarm installation
Part. 1 Part. 2 Common
–4–
∗88 Program Mode Lockout Options [0] ∗96, ∗97 Initialize/Reset Defaults
0 = standard *98 installer code lockout (reentry only by [∗] + [#] within This is a command, not a data field. See page 2.
50 seconds after power up)
1 = lockout [∗] + [#] reentry after *98 exit (reenter via installer code or ∗98, *99 Exit Commands
downloader only) This is a command, not a data field. See page 2.
2 = not used
3 = lockout local programming after *98 exit (reenter by downloader only) PAGER OPTIONS (✱160- ✱172)
∗89 Event Log Full Report Code [00] |
∗160 Pager 1 Phone No.
See box above field *59 for report code entries. | | | | | | | | | | | | | | | | | | |
Enter up to 20 digits. 0–9; #+11 = '✱'; #+12 = '#'; #+13 = 2-sec pause
∗90 Event Log Enables [3]
NOTE: System messages are logged when any non-zero entry is made.
∗161 Pager 1 Characters
0 = None | | | | | | | | | | | | | | |
1 = Alarm/Alarm Restore
2 = Trouble/Trouble Restore Enter the optional prefix characters, up to 16 digits.
4 = Bypass/Bypass Restore 0–9; #+11 = '✱'; #+12 = '#'; #+13 = 2-second pause.
8 = Open/Close. Example: To select “Alarm/Alarm Restore”, and
“Open/Close”, enter 9 (1 + 8); To select all, enter #15. ∗162 Pager 1 Report Options [0,0,0]

∗91 Option Selection


P1 P2 common
[8, 0] For each partition, select from the following options:
Options: 0 = None Options V21iPSIA 0 = no reports sent
4 = AAV UL: must use ADEMCO UVCM module Call Wait Disable 1 = Opens/closes all users
4 = All alarms and troubles
8 = Exit Delay Restart/Reset UL: must be disabled 5 = All alarms / troubles, and opens/closes for all users
#+12 = AAV and Exit Delay Restart/Reset 12 = Alarms / troubles for zones entered in zone list 9
SIA Guidelines: Exit Delay should be enabled. 13 = Alarms / troubles for zones entered in zone list 9, and
opens/closes for all users
V21iPSIA:
Options: Same as listed above. ∗163 Pager 2 Phone No.
Call Waiting Disable:
0 = call waiting not used | | | | | | | | | | | | | | | | | | |
1 = call waiting disable digits (*70) entered in field *40; (when Enter up to 20 digits. 0–9; #+11 = 'Q'; #+12 = '#'; #+13 = 2-sec pause
selected, the system dials the entry in field *40 only on
alternate dial attempts; this allows proper dialing in the event ∗164 Pager 2 Characters
call waiting service is later canceled by the user).
| | | | | | | | | | | | | | |
∗92 Phone Line Monitor Enable [0,0] Enter the optional prefix characters, up to 16 digits.
0–9; #+11 = '✱'; #+12 = '#'; #+13 = 2-second pause.
UL: see Inst. Instructions for requirements 1 2
Entry 1:: 0 = disabled, 1-15 = 1 min - 15 min ∗165 Pager 2 Report Options [0,0,0]
(#+10 = 10 min; #+11 = 11 min; #+12 = 12 min; #+13 = 13 min; #+14 P1 P2 common
= 14 min; #+15 = 15 min) See field *162 for reporting options. Select for each partition (use zone
Entry 2: list 10 if using options 12 or 13).
0 = Keypad display when line is faulted
1 = Keypad display plus keypad trouble sound ∗166 Pager 3 Phone No.
2 = Same as “1”, plus programmed output device STARTS. If either
partition is armed, external sounder activates also. | | | | | | | | | | | | | | | | | | |
NOTE: If “2” selected, Output Device must either be programmed
Enter up to 20 digits. 0–9; #+11 = '✱'; #+12 = '#'; #+13 = 2-sec pause
to be STOPPED in field ✱80 or STOPPED by Code + # + 8 +
output number.
∗167 Pager 3 Characters
∗93 Reports In Armed Period [1,0] | | | | | | | | | | | | | | |
Per Zone (Swinger Suppression) Restrict V21iPSIA Enter the optional prefix characters, up to 16 digits.
Restrict Report Pairs: Report Pairs Unlimited 0–9; #+11 = '✱'; #+12 = '#'; #+13 = 2-second pause.
0 = Unlimited Reports Reports Enable
1 = 1 report pair ∗168 Pager 3 Report Options [0,0,0]
2 = 2 report pairs SIA Guidelines: Must be set for option 1 or 2. P1 P2 common
See field *162 for reporting options. Select for each partition (use zone
V21iPSIA: list 11 if using options 12 or 13).
Restrict Report Pairs: 1 = 1 report pair; 2 = 2 report pairs
Unlimited Reports Enable:
0 = restrict reports to the setting in entry 1
∗169 Pager 4 Phone No.
1 = unlimited reports for zones listed in zone list 7; (use zone list 7 | | | | | | | | | | | | | | | | | | |
to enter those zones that require unlimited reporting; these
zones ignore the setting in entry 1) Enter up to 20 digits. 0–9; #+11 = '✱'; #+12 = '#'; #+13 = 2-sec pause

DOWNLOAD INFORMATION (✱94, ✱95)


∗170 Pager 4 Characters
| | | | | | | | | | | | | | |
∗94 Download Phone No.
Enter the optional prefix characters, up to 16 digits.
| | | | | | | | | | | | | | | | | | | 0–9; #+11 = '✱'; #+12 = '#'; #+13 = 2-second pause.
Enter up to 20 digits, 0–9; #+11 for '✱'; #+12 for '#'; #+13 for a 2-
second pause. Do not fill unused spaces. If fewer than 20 digits, exit ∗171 Pager 4 Report Options [0,0,0]
field by pressing ✱. To clear entries from field, press ✱94✱. P1 P2 common
UL: downloading may be performed only if a technician is at the site. See field *162 for reporting options. Select for each partition (use zone
Up/downloading via the Internet has not been evaluated by UL. list 12 if using options 12 or 13).

∗95 Ring Count For Downloading [15]


NOTE: Do not enter “0” if using 4286 Phone Module.
0 = Disable Station Initiated Download;
1–14 = number of rings (1–9, # +10 =10, # +11 =11,
# +12 =12, # +13 =13, # +14 =14);
15 = answering machine defeat (# +15 =15).

–5–
∗172 Pager Delay Option For Alarms [3] KEYPAD OPTIONS *189-*196
0 = none; 1 = 1 minute; 2 = 2 minutes; 3 = 3 minutes KEYPAD NOTES:
This delay is for ALL pagers in the system. 1. Options for keypad 1, address 16 are set by the factory and cannot be
changed.
MISCELLANEOUS SYSTEM FIELDS (*174-*181) 2. Each keypad must be assigned a unique address. Keypads programmed

∗174 Clean Me Reporting Options


with the same address will give unpredictable results.
[0] 3. If using Remote Services (IP/GSM feature), one of the keypad addresses
(for ESL smoke detectors) may be used for limited Remote Services features, though a physical
0 = disable; 1 = Clean Me signal reports; keypad is not installed. See ∗29 Menu Mode section for enabling Remote
NOTE: If Clean Me is enabled, you must enter “3” in field ✱56 Services.
programming for zone 1 response time.
∗177 Device Duration 1, 2 [0] [0] ∗189 Touch Screen Device
(used in *80 Menu mode-Device Actions 5/6) 1 2 (AUI) Enable [1] [1] AUI 1 AUI 2 AUI 3 AUI 4
0 = 15 seconds 6 = 2-1/2 min #+11 = 7 min System supports up to four touch screen style keypads (e.g.,
1 = 30 seconds 7 = 3 min #+12 = 8 min Symphony Advanced User Interface, and 6270 Touch Screen Keypad).
2 = 45 seconds 8 = 4 min #+13 = 10 min
AUI Compatibility Note: To ensure proper AUI device operation, use
3 = 60 seconds 9 = 5 min #+14 = 12 min
AUI devices with the following rev levels: 6270 series use version
4 = 90 seconds #+10 = 6 min #+15 = 15 min
1.0.9 or higher; 8132/8142 (Symphony) series use version 1.1.175 or
5 = 2 minutes
higher.
∗181 50/60 Hertz AC Operation [0] Touch Screen (AUI) device 1: Must set AUI device address to 1
Touch Screen (AUI) device 2: Must set AUI device address to 2
0 = 60 Hz; 1 = 50 Hz Touch Screen (AUI) device 3: Must set AUI device address to 5
CONFIGURABLE ZONE TYPE OPTIONS (*182-*185) Touch Screen (AUI) device 4: Must set AUI device address to 6
Enter each touch screen keypad’s home partition
(see Configurable Zone Type Worksheet on page 7) 0 = disable; 1 = partition 1; 2 = partition 2; 3 = partition 3 (common)
∗182 Configurable Zone Type 90 NOTES: 1. Use of touch screen style keypads does not affect the
number of standard keypads supported.
2. If using Remote Services (IP/GSM feature), one of the touch
screen (AUI) addresses may be used for enhanced Remote
1 2 3 4 5 6 7 8 9 10 Services feature set, though a physical touch screen is not
Enter the appropriate value for each entry, 1-10, based on the charts installed. See ∗29 Menu Mode section for enabling Remote
provided on the next page. Each entry is the sum of the values of its Services.
selected options
(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14, #+15=15). ∗190 Keypad 2 Device Address 17 [0] [0]
UL: Do not configure zones as a fire alarm or UL burglar alarm zone. Partition: Enter partition where: Part. Sound

∗183 Zone Type 90 Report Codes


0 = keypad disabled; 1-3 = part. no. (3 = com)

IMPORTANT: Use existing Contact ID® codes, if appropriate, or Sound: 0 = no suppression


define unique codes in CID code range 750-789. See important note 1 = suppress arm/disarm and E/E beeps
in installation instructions. 2 = Suppress chime beeps only
3 = suppress arm/disarm, E/E, and chime beeps
90 ALARM ID: XXX
TROUBLE ID: XXX ∗191 Keypad 3 Device Address 18 [0] [0]
Enter the desired 3-digit Contact ID® report codes for alarms and
See field ∗190 for entries. Partition Sound
troubles occurring on zones assigned to this zone type. Enter the
codes sequentially (all 6 digits). When entering digits, [#] moves
cursor back, [∗] moves forward. ∗192 Keypad 4 Device Address 19 [0] [0]
NOTE: Zone alarm report codes (prompt in ∗56 Menu mode) and
See field ∗190 for entries. Partition Sound
trouble report code (∗60) and relevant restore codes (∗70, ∗71) must
be enabled in order for the configurable zone type codes to be
reported. ∗193 Keypad 5 Device Address 20 [0] [0]
Press [∗] when done to continue.
See field ∗190 for entries. Partition Sound
∗184 Configurable Zone Type 91
∗194 Keypad 6 Device Address 21 [0] [0]
1 2 3 4 5 6 7 8 9 10 See field ∗190 for entries. Partition Sound
See ∗182 for entries. Press [∗] when done to continue.
UL: Do not configure zones as a fire alarm or UL burglar alarm zone. ∗195 Keypad 7 Device Address 22 [0] [0]
∗185 Zone Type 91 Report Codes See field ∗190 for entries. Partition Sound
IMPORTANT: Use existing Contact ID® codes, if appropriate, or
define unique codes in CID code range 750-789. See important note
in installation instructions.
∗196 Keypad 8 Device Address 23 [0] [0]
91 ALARM ID: XXX See field ∗190 for entries. Partition Sound
TROUBLE ID: XXX
See *183 for entries. Press [∗] when done to continue.
∗197 Exit Time Display Interval [0]
0 = no display; 1-5 = seconds between display refresh
NOTE: If enabled and using only 2-digit fixed-word keypads (e.g.,
6150RF), do not set exit delay time greater than 96 seconds. See Inst.
Instr. for explanation.
TOUCH SCREEN DEVICE NOTE: If using more than one touch
screen device (e.g., 6270, Symphony) with the system, leave field
*197 Exit Time Display Interval set to the default value “0.” The 6270
automatically displays remaining exit time in one-second increments.

∗198 Display Partition Number [0]


(for Alpha Display Keypads)
0 = no; 1 = yes (partition no. appears on Alpha Display)

∗199 ECP Fail Display [0]


0 = 3-digit display (“1” + device address)
1 = 2-digit fixed-display as “91”

–6–
Configurable Zone Types Worksheets
Configurable zone types 90 and 91 can be programmed via downloader software or from a keypad using data fields*182-
*185. Configurable zone types 92 and 93 can only be programmed using the downloader software.
Programming Configurable Zone Type options involves making 10 entries in data field *182 for zone type 90 and field *184 for
zone type 91, where each entry represents the sum of the values of the various options shown in the tables below. Use fields
*183 and *185 to program Contact ID report codes for these zone types.

ENTRY 1 (See note 5 for RF zones) ENTRY 2 (See note 5 for RF zones) Entries for Fields *182 and *184
Response when system disarmed and zone is: Auto Entry Zone Type 90 Zone Type 91
Intact EOL Open Shorted Restore Vent Zone (field *182) (field *184)
RF zone normal RF zone N/A RF zn off-normal 1
0 = normal 0 = normal 0 = normal 0 = no 0 = no 2
1 = alarm 4 = alarm 1 = alarm 4 = yes 8 = yes 3
2 = trouble 8 = trouble 2 = trouble 4
3 = fault 12 = fault 3 = fault
see note 6 5
Entry 1 = EOL + Open Entry 2 = Short + auto restore + vent zone 6
7
ENTRY 3 (See note 5 for RF zones) ENTRY 4 (See note 5 for RF zones) 8
Response when armed STAY and zone is: Byp. when Byp. when 9
Intact EOL Open Shorted disarmed armed 10
RF zone normal RF zone N/A RF zn off-normal
0 = normal 0 = normal 0 = normal 0 = no 0 = no To calculate the value for each entry:
1 = alarm 4 = alarm 1 = alarm 4 = yes 8 = yes Simply add the values of the selected options
2 = trouble 8 = trouble 2 = trouble in each of the entry’s columns (one option per
3 = fault 12 = fault 3 = fault column). For example, to program Entry 2 for
see note 6 “alarm response to short,” “auto restore on,”
Entry 3 = EOL + Open Entry 4 = Short + byp. disarmed + byp. armed but not a “vent zone,” enter 5 (“1” for alarm
short + “4” for auto restore yes + “0” for vent
ENTRY 5 (See note 5 for RF zones) ENTRY 6 (See note 5 for RF zones) zone no).
Response when armed AWAY and zone is: Dial Delay Fault Delay
Intact EOL Open Shorted (see field *50) (see field *87)
RF zone normal RF zone N/A RF zn off-normal
0 = normal 0 = normal 0 = normal 0 = no 0 = no
1 = alarm 4 = alarm 1 = alarm 4 = use delay 8 = use delay
2 = trouble 8 = trouble 2 = trouble
3 = fault 12 = fault 3 = fault see note 1 INTACT OPEN SHORTED
EOL
see note 6 ZONE-003-V0

Entry 5 = EOL + Open Entry 6 = Short + dial delay + fault delay Zone Conditions Represented
in Entries 1-6
ENTRY 7 ENTRY 8
Display Faults Power Reset/ Use Entry Use Exit Respond as NOTES:
Verification Delay 1/2 Delay Interior Type 1. Do not use the “fault delay” option with a
0 = show alarms 0 = no 0 = no 0 = no 0 = no configurable zone type if it is set for an
when armed 4 = power reset 1 = delay 1 4 = use exit 8 = yes entry or exit delay, otherwise
& disarmed after fault 2 = delay 2 delay unpredictable results may occur.
1 = don’t show (by code + OFF) see note 2 2. To create an interior type zone, select
alarms when 12 = verification “respond as interior zone type” (entry 8,
armed (show (see zone interior type = yes), and set zone
alarms, trbles, type 16) response to “fault” in entries 3-4 to ensure
faults when fault displays; do not set as “normal,”
disarmed) “alarm,” or “trouble.”
3 = never show 3. Do not set fire zones to respond as a
any alarms, “fault” (entries 1-6), otherwise faults will
trbles, faults
not display unless the [∗] key is pressed.
Entry 7 = fault display + power Entry 8 = entry delay 1/entry delay 2 + exit delay +
reset/verification interior zone type 4. 4219/4229 modules must use EOLRs or
unpredictable results may occur.
ENTRY 9 ENTRY 10 5. RF Zones: The “open” option in entries 1,
Alarm Sounds Use Bell Respond as Trouble Chime when 3, and 5 is not applicable for RF zones.
Timeout Fire Zone Sounds Chime Mode On Use the “intact EOL” option for normal RF
0 = none 0 = no 0 = no 0 = none 0 = no zone conditions and “shorted” for off-
1 = steady 4 = yes 8 = yes 1 = periodic 4 = yes normal RF zone conditions.
keypad beep 6. a. Zone-Doubling/Double-Balanced: A
2 = steady bell see fields *32, see zone type 2 = trouble short on either zone of a zone-doubled
and keypad *33 09; see note 4 beeps pair or on a double-balanced zone
3 = pulsing bell causes a tamper condition.
and keypad b. For double-balanced zones, this entry
Entry 9 = alarm sounds + bell timeout + fire zone Entry 10 = trouble sounds + chime must be “0.”
c. For zone-doubled zones, both zones
of the doubled pair must be assigned
the same response to a short.

–7–
*56 Zone Programming Menu Mode
(press *56 while in Program mode)
The Zone Programming Worksheet is on page 18.
For each of the following prompts, make the desired entry, followed by the [∗] key to accept the entry.
Refer to the Installation and Setup Guide for detailed explanations for each prompt.

SET TO CONFIRM? XMIT TO confirm


0 = no; 1 = yes (See XMIT TO CONFIRM prompt later in this section.) We Appears if you answered “Yes” at the “Set to Confirm” prompt.
recommend that you confirm the programming of every transmitter. Activate the loop input or button that corresponds to this zone.
Press [∗] to continue.
ENTER ZN NUM. If the serial/loop number transmitted does not match the serial number
01-64, 91, 92, 95, 96, 99 entered, a display showing the entered and the received serial/loop numbers
To quit, enter 00 to quit (returns to data field mode). appears.
SUMMARY SCREEN: If so, activate the loop input or button on the transmitter once again. If a
System displays a summary of the entered zone’s current programming. match is not obtained, press the [#] key twice and then enter (or transmit)
the correct serial number.
Press [∗] to continue.
Press [∗] to continue
ZONE TYPE If the serial number transmitted matches the serial number entered,
00 = Not used 07 = 24-Hr Audible 20 = Arm–STAY* the keypad will beep 3 times and a summary display will appear,
01 = Entry/exit #1 08 = 24-Hr Aux 21 = Arm–AWAY* showing that zone's programming. An “s” indicates that a
02 = Entry/exit #2 09 = Fire 22 = Disarm* transmitter’s serial number has been enrolled.
03 = Perimeter 10 = Interior w/Delay 23 = No Alarm Resp Press [∗] to accept the zone information and continue.
04 = Interior Follower 12 = Monitor Zone 24 = Silent Burglary
05 = Trouble Day/Alarm Night 14 = Carbon Monoxide 77 = Keyswitch PROGRAM ALPHA?
06 = 24-Hr Silent 16 = Fire w/Verify 81 = AAV Monitor Press 1 if you want to program descriptors for the zone now, and refer to the
Zone *82 Descriptor Programming section for procedure. To program descriptors
*5800 button-type transmitters only 90-91 = Configurable later, enter 0 (no).
Press [∗] to return to the ENTER ZN NUM prompt.
PARTITION
1, 2, or 3-common
REPORT CODE
1-9, 10 for 0, 11 for B, 12 for C, 13 for D, 14 for E, 15 for F ∗58 Expert Zone Programming Mode
For Contact ID®, enter any non-zero entry as the first digit to enable (press ∗58 while in Data Programming mode)
reporting for this zone.
To disable the report code for this zone, enter 00. SET TO CONFIRM?
HARDWIRE TYPE Select whether you want confirmation of wireless device enrollment. (See
“XMIT TO CONFIRM” prompt later in this section.) We recommend that
Appears only for zones 02-08. Zone 1 is automatically set for EOL
you confirm the programming of every transmitter.
operation. Enter the desired hardwire type:
0 = EOL; 1 = NC; 2 = NO; 3 = zone doubling (ZD); 4 = double-balanced SUMMARY SCREEN
(DB)
RESPONSE TIME Zn ZT P RC HW: RT
For hardwired zones 01-08. Enter the desired response time for this zone:
01 09 1 10 EL 1
0 = 10mSec; 1 = 350mSec; 2 = 700mSec; 3 = 1.2 secs (see field ∗174).
NOTE: If zone doubling is being used, the response time selected for zones (Typical for Zone 1, initial summary screen)
02-08 automatically applies to each zone’s associated doubled zone.
INPUT TYPE Zn ZT P RC IN: L
Skipped for zones 2-8, and for zones 10-16 if zone-doubling enabled. Enter 10 00 1 10 RF: –
the input type: 2 = AW (Aux wired zone); 3 = RF (supervised RF);
4 = UR (unsupervised RF); 5 = BR (unsupervised button type) (Typical for entered zone number; zone 10 in this example)
NOTE: To change the input type of a previously programmed wireless System displays summary of zone 1’s current programming.
device to a wired zone, you must first delete the transmitter’s serial number. Enter the zone number being programmed, then press [∗]. A summary
screen for that zone is displayed, along with any current programming
INPUT S/N values, and the cursor moves to the Zone Type location. The cursor then
Enroll the transmitter’s serial number and loop number as follows:
automatically moves to the next locations after each entry is made.
1. a. Transmit two open/close sequences (for button-type transmitters,
press and release the button twice, waiting about 4 seconds before Special Function Keys:
pressing the button the second time). • [A] (Advance) and [B] (Back) keys on the keypad move the cursor
OR within the screen.
b. Manually enter the 7-digit serial number printed on the label of the • [C] (Copy) key will insert the previous zone’s attributes, if desired.
transmitter. Press the [∗] key to move to the “L” position, then enter • [D] key starts the Wireless Key Programming Templates menu
the loop number. (see Wireless Key Programming Templates section that follows this
Use the [A] (Advance) and [B] (Back) keys to move the cursor forward section).
and back within the screen. Pressing the [C] (Copy) key will insert the
previously enrolled serial number, if desired (used when programming Sequentially enter Zone Type (ZT), Partition (P), and Report Code (RC; 0-9
a transmitter with several input loops). only; use ∗56 menu mode for hex codes), then Hardwire Type (HW) and
Response Time (RT) for basic wired zones 1-8 or Input Device Type (IN) for
To delete an existing serial number, enter 0 in the loop number
zones 9 and higher (Loop Number [L] is programmed at the INPUT S/N
field. The serial number will change to 0's. If 0 was entered in error,
prompt).
simply re-enter the loop number or press [#], and the serial number
See *56 Zone Programming Menu Mode section described earlier for entry
will return to the display.
values.
2. Press [∗] to continue. The system now checks for a duplicate serial/loop
number. Press [∗] to save the programming and continue. If needed, press the [#]
If no duplicate is found, the display shows the serial number and loop key to back up without saving.
number.
• For wireless devices (input types RF, UR, BR), continue to the INPUT
3. Press [∗] to continue to confirmation screen.
S/N (serial number/loop number) and XMIT TO CONFIRM prompts
described earlier in the *56 Zone Programming Menu Mode section.
When done, the display returns to the initial summary screen prompt to
let you program the next zone.
(prompts continued in next column) • For wired devices, the display returns to the initial summary screen
prompt to let you program the next zone.
To Quit, enter 00 at the zone number location and press [∗].

–8–
Wireless Key Programming Templates (press the [D] key from *58 Menu mode Summary Screen)
This procedure programs the wireless keys, but a key is not active for arming/disarming until it is assigned to a user number (see
System Operation section, Assigning Attributes Command in the Installation Instructions).
TEMPLATE ? ENTER START ZONE
Enter desired template number 1–6 (see chart below), then press [∗] to The system displays the lowest zone number of the highest available
continue. consecutive 4-zone group.
To exit the Template screen, press [#]. The system returns to the *58 Menu To start at a different zone number, enter the zone desired, and press [∗]. If
mode Summary Screen. the system has four consecutive zones beginning with that zone, the zone
number is displayed. If not, the system will again display a suggested zone
TEMPLATE SUMMARY that can be used.
If the required number of consecutive zones is not available at all, the
L 01 02 03 04 system will display “00”.
T 23 22 21 23
Press [∗] to accept.
The selected template is displayed. Continue to the INPUT S/N (serial number/loop number) and XMIT TO
The top line represents loop numbers, the bottom line represents each CONFIRM prompts described earlier in the *56 Menu Mode section.
loop’s zone type.
IMPORTANT: When confirmed, the key is not active for arming/disarming
Press [∗] to accept template and continue. until it is assigned to a user number (using the assigning attributes command,
PARTITION attribute “4”). See System Operation section in Installation Instructions.
Enter the partition (1, 2) in which the key is to be active. When done, the keypad beeps three times and the display returns to the
Press [∗] to continue. ENTER START ZONE prompt to let you enter the starting zone for the next
wireless key.
Wireless Key Predefined Default Templates
For 5804 Loop Function Zone Type For 5804BD Loop Function Zone Type
TEMPLATE 1 1 No Response 23 TEMPLATE 4 1 No Response 23
2 Disarm 22 2 No Response 23
3 Arm Away 21 3 Arm Away 21
4 No Response 23 4 Disarm 22
TEMPLATE 2 1 No Response 23 TEMPLATE 5 1 No Response 23
2 Disarm 22 2 Arm Stay 20
3 Arm Away 21 3 Arm Away 21
4 Arm Stay 20 4 Disarm 22
TEMPLATE 3 1 24-hour audible 7 TEMPLATE 6 1 24-hour audible 7
2 Disarm 22 2 Arm Stay 20
3 Arm Away 21 3 Arm Away 21
4 Arm Stay 20 4 Disarm 22

*57 Function Key Programming (press ∗57 while in Data Programming mode)
The Function Key Worksheet is on page 19.
PRESS KEY TO PGM KEY "A" FUNC (continued)
Press the desired function key to be programmed, A-D, then press [∗] to 01 = Single-button paging (sends a 999-9999 message to pager)
continue. 02 = Display time
When done, press 0 to exit this mode and return to data field mode. 03 = Arm AWAY (reports as User 00 if closing reports are enabled)
NOTE: A key programmed as a function key is no longer available to be 04 = Arm STAY (reports as User 00 if closing reports are enabled)
used as an end-user macro key or panic key. 05 = Arm NIGHT-STAY (reports as User 00 if closing reports enabled)
06 = Step Arming (arms STAY, then NIGHT-STAY if enabled, then
PARTITION AWAY)
Enter the partition (1-3) in which this function key will be active. 07 = Output Device Command (for device programmed as system
KEY "A" FUNC operation type 66 in *80 Menu Mode)
Enter the desired function for this key: 08 = Communication Test (sends Contact ID code 601)
00 = For the Function key selected, the functions are pre-defined as 09 -12= Macro Keys 1-4 respectively (defined by [#] [6] [6] command)
follows (default):
If A selected = Zone 95 (emergency key, same as [1] [∗] pair) Press [∗] to continue; returns to key number prompt with the next function key letter
displayed.
If B selected = Zone 99 (emergency key, same as [∗] [#] pair)
If C selected = Zone 96 (emergency key, same as [3] [#] pair)
If D selected = Single-button paging (continued in next column)

–9–
∗79 Output Device Menu Mode ∗80 Menu Mode (continued)
(press ∗79 while in Programming mode)
The *79 Device Mapping Worksheet is on page 19. OUTPUT ACTION
0 = off; 1 = Close for 2 seconds; 2 = Close and Stay Closed; 3 = Continuous
ENTER OUTPUT NO. Pulse 1 sec on and 1 sec off
01-18 = relays/X-10 4 = Change Device State; 5 = Duration 1 (see data field *177); 6 = Duration
2 (see data field *177)
[∗] to continue
Press [∗] to continue.
OUT NORM LOW (appears only for triggers 17/18)
0 = no (standard default); sets the output level normally high
ENTER OUTPUT NO.
1 = yes; sets the output normally low (can be used for resetting 4-wire Enter the device output number (programmed in *79 Menu Mode) you want
smoke detectors) associated with this output.
01-16 = output no.; 17-18 = on-board triggers
[∗] to return to Output Number prompt
Press [∗] to continue.
OUTPUT TYPE
0 = delete; 1 = relay (skip to “B” prompt); 2 = Powerline Carrier device (skip
SUMMARY SCREEN
to “A” prompt) A summary screen appears showing the programmed settings.
[∗] to continue. Press [∗] to return to OUTPUT FUNCTION NUMBER prompt.

A: UNIT No. (if X-10 was selected as Output Type)


Enter the unit code (01-16, set at the device).
[∗] to return to the Output Number prompt continue
*81 Zone List Menu Mode
(press *81 while in Programming mode)
B: MODULE ADDR (if relay was selected as Output Type) The Zone List Worksheet is on page 19.
Enter the predefined address for this module (07-15; see Table of Device
Addresses on page 2). ZONE LIST NO.
Make sure the module’s DIP switches are set to the selected address. Enter the zone list number (01-12) to program (or 00 to exit this mode).
NOTE: If using Multi-Mode (IP/GSM feature), select one of the 4204 Press [∗] to continue.
addresses, though a physical 4204 module is not installed. If using 2-4204
multi-mode option, the second 4204 address is automatically one number
ENTER ZN NUM.
higher than the first one selected. Make sure these addresses are not used Enter each zone number (01-64) to add to the zone list, followed by pressing
by physical 4204 modules that may be installed. See ∗29 Menu Mode [∗] (example, 01∗, 02∗, 03∗).
section for enabling Multi-Mode. Press 00 to continue.
[∗] to continue IMPORTANT: Do not include fire zones in zone lists that are used to STOP
device actions.
REL POSITION (actual relay number on module)
For 4204 modules, relay numbers are 1-4. For 4229 modules, relay DEL ZN LIST?
numbers are 1-2. 0 = don’t delete list; current zone list remains saved
NOTE: If using multi-mode, program the relays to trigger on those system 1 = delete this zone list; All zones in the zone list will be deleted.
events to be sent to the user’s email address. See ∗29 Menu Mode section [∗] to continue
for enabling Multi-Mode.
DELETE ZONE?
[∗] to return to the Output Number prompt for programming the next device
0 = don’t delete zones; save the entire zone list and return to the Zone List
No. prompt
∗80 Output Function Menu Mode 1 = go to next prompt to delete zones
[∗] to continue
(press ∗80 while in Programming mode)
The Output Definition Worksheet is on page 20. ZN TO DELETE?
Enter each zone (01-64) to be deleted from the list, following each with [∗].
OUTPUT FUNCT. # 00 when done to return to the Zone List No. prompt.
Enter the output function number to be defined: 01-48
[∗] to continue; 00 = exit
SUMMARY SCREEN *82 Alpha Descriptor Programming
01 A E P Trig
PRE-DEFINED DESCRIPTORS
?00 0 0 – ZL=00
This screen displays a summary of the current output programming PROGRAM ALPHA
A = Output Action; E = Triggering event; P = Partition; Trig = Trigger type 0 = no (quit Alpha mode)
Question mark indicates the device shown has not been mapped. Use *79 1 = yes
Menu mode to map the device. Press [∗] or [#] to continue.
[∗] to continue
ACTIVATED BY CUSTOM WORDS
0 = delete (deletes the output function and any previous programming); a 0 = no (continue to descriptor programming)
confirmation prompt appears. 1 = yes (go to custom word programming)
Press 0 to program standard alpha descriptors. The system will then display
To delete this output definition, press 1. If you do not want to delete this
the descriptor for zone 1.
output, press 0.
To program custom words, press 1 (custom words are described later).
1 = zone list (go to “A” prompt); 2 = zone type (go to “B” prompt); 3 = zone Press [∗] to continue.
number (go to “C” prompt)
Press [∗] to continue ∗ ZN 01
“A” (if zone list was selected) Descriptor screen for zone 1 appears. To program a descriptor (up to 3
ZN LIST words) for a zone, do the following:
Enter the desired zone list number (01-08). At the ENTER EVENT prompt, 1. Press [∗] plus the desired zone number (existing descriptor, if any, is
enter the zone list event that will activate this output (0 = restore; 1 = alarm; displayed), then press [∗] plus the zone number again (flashing cursor
2 = fault; 3= trouble) appears).
Press [∗] to continue and skip to the “Output Action” prompt. 2. a. Press [#] plus the 3-digit number from the Alpha Vocabulary List on
page 11 for the first word.
“B” (if zone type was selected) b. Press [6] to accept the word and move the cursor for the next word.
ENTER ZN TYPE 3. Repeat steps 2a and 2b for the second and third words (if used).
Enter the desired zone type. See list below *80 Worksheet for zone types. 4. When all words have been entered, press [8] to save the descriptor for
At the PARTITION prompt, enter the partition in which this zone type will that zone. The flashing cursor disappears.
occur (0 = any partition; 1 = partition 1; 2 = partition 2; 3 = partition 3). 5. Repeat steps 1-4 to assign a descriptor for the next zone.
Press [∗] to continue and skip to the “Output Action” prompt. 6. When all descriptors have been entered, press [∗] + 0 + 0 (or simply
press [#]) after the last descriptor has been saved to return to the
“C” (if zone number was selected) PROGRAM ALPHA? prompt.
Enter 0 (no) at the prompt to exit this mode and return to Data Field mode.
ENTER ZN NO.
Enter the desired zone number, then press [∗] to continue. At the ENTER
EVENT prompt, enter the zone event that will activate this output (0 =
restore; 1 = alarm/fault/trouble).
Press [∗] to continue to the OUTPUT ACTION prompt

– 10 –
*82 Alpha Descriptor Programming (continued)
ADDING CUSTOM WORDS (up to 10 words)
For custom words, the keys have the following functions: 4. Repeat Step 3 to create the desired word(s). Each word can be a
maximum of 10 characters (except custom message/partition descriptor
[4] moves cursor one space to the left. word numbers 11, 12, and 13, which can be a maximum of 16 characters).
[6] moves cursor one space to the right. 5. When the word is complete, press the [8] key to save the custom word(s)
[8] saves the new word in the system's memory. in the vocabulary list and return to the “CUSTOM WORD ?” display.
6. Repeat Steps 1–5 for other custom words to be entered. To change a
1. Select Custom Word mode (enter 1) when the prompt “CUSTOM WORD ?”
custom word, just overwrite it. When all words have been programmed,
is displayed.
enter 0 at the “CUSTOM WORD ?” prompt to return to the Program
2. Enter the number (01–10, or 11, 12, 13 for partition descriptors– see Alpha prompt. Enter 0 again to exit Descriptor mode.
below) of the custom word or word string to be created, corresponding to
index numbers 245 - 254 respectively. A cursor appears at the beginning To Assign Partition/Custom Message Descriptors, use Adding Custom
of the second line. Words procedure, but: use the following word numbers in step 2:
NOTE: Custom words 8, 9, and 10 are “reminder words” that can be 11 = partition 1; 12 = partition 2; 13 = common lobby
programmed to display using Scheduling Mode.
3. Refer to the Character (ASCII) Chart on the next page.
Press [#], followed by the two-digit entry for the first letter you would like
to display (e.g., # 6 5 for “A”). The cursor moves to the right, in position
for the next character.
To delete a character, simply enter the SPACE character (#32) at the
unwanted character’s location.
ALPHA VOCABULARY LIST (For Entering Zone Descriptors)
000 (Word Space) • 057 DOOR ∗ –L– –R– –V–
–A– • 059 DOWN • 106 LAUNDRY ∗ 155 RADIO 209 VALVE
• 001 AIR • 060 DOWNSTAIRS • 107 LEFT • 156 REAR 210 VAULT
• 002 ALARM ∗ 061 DRAWER 108 LEVEL 157 RECREATION 212 VOLTAGE
004 ALLEY • 062 DRIVEWAY • 109 LIBRARY ∗ 159 REFRIGERATION –W–
005 AMBUSH • 064 DUCT • 110 LIGHT 160 RF 213 WALL
• 006 AREA –E– 111 LINE • 161 RIGHT 214 WAREHOUSE
• 007 APARTMENT • 065 EAST • 113 LIVING ∗ • 162 ROOM ∗ • 216 WEST
• 009 ATTIC ∗ 066 ELECTRIC • 114 LOADING 163 ROOF • 217 WINDOW ∗
010 AUDIO 067 EMERGENCY ∗ 115 LOCK –S– • 219 WING
–B– 068 ENTRY 116 LOOP 164 SAFE 220 WIRELESS
• 012 BABY ∗ • 069 EQUIPMENT 117 LOW 165 SCREEN –X–
• 013 BACK ∗ • 071 EXIT ∗ • 118 LOWER 166 SENSOR 222 XMITTER
• 014 BAR 072 EXTERIOR –M– • 167 SERVICE –Y–
• 016 BASEMENT ∗ –F– • 119 MACHINE • 168 SHED ∗ 223 YARD
• 017 BATHROOM ∗ • 073 FACTORY 121 MAIDS 169 SHOCK –Z–
• 018 BED 075 FAMILY 122 MAIN ∗ • 170 SHOP ∗ 224 ZONE (No.)
• 019 BEDROOM ∗ • 076 FATHERS • 123 MASTER ∗ 171 SHORT • 225 ZONE ∗
020 BELL • 077 FENCE • 125 MEDICAL ∗ • 173 SIDE ∗ • 226 0
• 021 BLOWER • 079 FIRE ∗ 126 MEDICINE 174 SKYLIGHT • 227 1
• 022 BOILER • 080 FLOOR ∗ 128 MONEY 175 SLIDING ∗ • 228 1ST ∗
023 BOTTOM 081 FLOW 129 MONITOR • 176 SMOKE ∗ • 229 2
025 BREAK 082 FOIL • 130 MOTHERS • 178 SONS • 230 2ND ∗
• 026 BUILDING • 083 FOYER • 131 MOTION ∗ • 179 SOUTH • 231 3
–C– 084 FREEZER 132 MOTOR 180 SPRINKLER • 232 3RD ∗
028 CABINET • 085 FRONT ∗ –N– • 182 STATION • 233 4
• 029 CALL –G– • 134 NORTH 184 STORE • 234 4TH
030 CAMERA • 089 GARAGE ∗ 135 NURSERY • 185 STORAGE ∗ • 235 5
031 CAR • 090 GAS –O– 186 STORY • 236 5TH
033 CASH 091 GATE • 136 OFFICE ∗ 190 SUPERVISED ∗ • 237 6
034 CCTV • 092 GLASS • 138 OPEN ∗ 191 SUPERVISION • 238 6TH
035 CEILING 093 GUEST 139 OPENING 192 SWIMMING • 239 7
036 CELLAR 094 GUN • 140 OUTSIDE 193 SWITCH • 240 7TH
• 037 CENTRAL –H– 142 OVERHEAD –T– • 241 8
038 CIRCUIT • 095 HALL ∗ –P– 194 TAMPER • 242 8TH
• 040 CLOSED ∗ • 096 HEAT 143 PAINTING 196 TELCO • 243 9
• 046 COMPUTER 098 HOLDUP • 144 PANIC ∗ 197 TELEPHONE • 244 9TH
047 CONTACT 099 HOUSE ∗ 145 PASSIVE • 199 TEMPERATURE
245 Custom Word #1
–D– 100 INFRARED • 146 PATIO ∗ 200 THERMOSTAT
246 Custom Word #2
• 048 DAUGHTERS • 101 INSIDE ∗ 147 PERIMETER • 201 TOOL
247 Custom Word #3
049 DELAYED 102 INTERIOR • 148 PHONE 202 TRANSMITTER
248 Custom Word #4
• 050 DEN ∗ 103 INTRUSION 150 POINT –U–
249 Custom Word #5
051 DESK –J– 151 POLICE ∗ • 205 UP
250 Custom Word #6
• 052 DETECTOR ∗ 104 JEWELRY 152 POOL ∗ • 206 UPPER
251 Custom Word #7
• 053 DINING ∗ –K– • 153 POWER • 207 UPSTAIRS ∗ 252 Custom Word #8
054 DISCRIMINATOR • 105 KITCHEN ∗ • 208 UTILITY ∗ 253 Custom Word #9
055 DISPLAY 254 Custom Word #10

Note: Bulleted (•) words in boldface type are those that are also available for use by the 4286 Phone Module. If using a Phone module,
and words other than these are selected for Alpha descriptors, the module will not provide annunciation of those words.
Italicized words followed by an asterisk indicate those words supported by the 6160V/6150V Voice Keypads
CHARACTER (ASCII) CHART (For Adding Custom Words)
32 (space) 41 ) 50 2 59 ; 68 D 77 M 86 V
33 ! 42 * 51 3 60 < 69 E 78 N 87 W
34 " 43 + 52 4 61 = 70 F 79 O 88 X
35 # 44 , 53 5 62 > 71 G 80 P 89 Y
36 $ 45 – 54 6 63 ? 72 H 81 Q 90 Z
37 % 46 . 55 7 64 @ 73 I 82 R
38 & 47 / 56 8 65 A 74 J 83 S
39 ' 48 0 57 9 66 B 75 K 84 T
40 ( 49 1 58 : 67 C 76 L 85 U

– 11 –
∗29 Internal Device Menu Mode
(for Programming IP and GSM Module Options) 7720P Emulation Template for Alpha Keypads
This mode is for programming the Internet connection (IP) and GSM Module
configuration, collectively referred to as the Internal Device.
NOTE: The Internal Device is automatically set to address 3 and cannot be
changed.

IMPORTANT: The use of the IP connection or the VISTA-GSM module


requires an AlarmNet–I account. Please obtain the account information
from the central station prior to programming this module.
A B C
The following section describes the programming of the internal device ARMED (A) BS/ESC 1 OFF 2 AWAY 3 STAY
options using an alpha keypad. Alternatively, these options can be D E F
programmed via the AlarmNet Direct website. After programming is (B)
complete, the control must be registered with AlarmNet (via the control’s
READY / 4 MAX 5 TEST 6 BYPASS

S T X
RJ45 Internet connection). Refer to the Registration with AlarmNet section
for procedures. SHIFT
(C) N/Y 7 INSTANT 8 CODE 9 CHIME

FUNCTION SPACE ENTER


Using an Alpha Keypad as a 7720P Programming Tool WHEN LIT (D) SHIFT READY 0 #
When programming IP/GSM features (with ∗29 menu mode), the alpha
keypad mimics the functions of the 7720P Programming Tool. See figure at
right and table below for 7720P key functions. Each key has two possible
functions: a normal function and a SHIFT function. 6160-7720P-001-V0

Normal functions: The numeric values labeled directly on the keys and
the left-hand functions shown in diagram on the ABC keys. To perform a
normal key function, simply press the desired key.
SHIFT functions: Those functions shown in diagram above the numerical
keys and the right-hand functions shown on the ABC keys. To perform a
SHIFT key function, press SHIFT key (D key), then press the desired
function key (shift function is indicated by the lit READY LED).

Normal and SHIFT key Functions While in ∗29 Menu Mode


Key Normal Key Function SHIFT Key Function
(A) = BS/ESC [BS]: Press to delete entry [ESC]: Press to quit Program Mode
Also, can reset EEPROM defaults †
(B) = ↓/↑ [↓]: Scroll down programming [↑]: Scroll up programming
(C) = N/Y [N]: Press for "NO" answer [Y]: Press SHIFT-Y for "YES" answer
(D) = SHIFT Press before pressing a SHIFT key function. Will light READY LED. LED goes out once a key is pressed. Press again for
each SHIFT function desired.
1/A [1]: For entering the number 1 [A]: Used for entering C.S. ID number
2/B [2]: For entering the number 2 [B]: Used for entering C.S. ID number
3/C [3]: For entering the number 3 [C]: Used for entering C.S. ID number
4/D [4]: For entering the number 4 [D]: Used for entering C.S. ID number
5/E [5]: For entering the number 5 [E]: Used for entering C.S. ID number
6/F [6]: For entering the number 6 [F]: Used for entering C.S. ID number
7/S [7]: For entering the number 7 [S]: Press to display diagnostic status
8/T [8]: For entering the number 8 [T]: Press to send TEST messages
9/X [9]: For entering the number 9 [X]: Press to reset the IP/GSM
[∗] / SPACE [∗]: Used to select programming options [SPACE]: Not used
0 [0]: For entering the number 0
[#] / ENTER [#] / ENTER: Press to accept entries No SHIFT function
† Active only when the "REVIEW?" prompt is displayed

Internal Device (IP and GSM) Default Values


The programming default values for ∗29 Menu Mode are listed in the Table below.
OPTION STANDARD DEFAULT VALUE ACTUAL ENTRY
1 Internal Device IP
2 Primary City ID ??
3 Primary CS ID ??
4 Primary Sub ID ????
5 Supervision 24 Hours
6 GSM Rollover Y/N N (if GSM enabled)
7 GSM 24Hr Tst Y/N N (if GSM enabled)
8 Old Alarm Time 10 Minutes
9 IP Fault Time 60 Minutes
10 GSM Fault Time 60 Minutes (if GSM enabled)
11 Notify Panel Of Neither Fault (if IP and GSM enabled)
12 Use DHCP Y/N Y (if IP or IP/GSM enabled)
13 NIC IP Address 255.255.255.255 (if DHCP not used)
14 Subnet Mask 255.255.255.255 (if DHCP not used)
15 Gateway IP Addr 255.255.255.255 (if DHCP not used)
16 DNS IP Addr. 255.255.255.255 (if DHCP not used)
Status and Contact ID Reporting Codes
The Internal Device (IP/GSM) sends status messages to the control panel for network connectivity failures. Trouble messages are displayed on the keypad as
“Check 103,” with status displayed as “LngRng Radio” followed by a 4-digit keypad display status code, defined below.
Keypad Display Status Codes Contact ID Codes (as displayed at 685) sent to CS via IP/GSM
CODE DESCRIPTION CODE DESCRIPTION
0000 Control panel lost communication with internal device E339 C803 Power-on reset
0005 internal device has lost contact with AlarmNet-G network E350 C951 Primary communication path failure (Ethernet)**
000F internal device is not registered; account not activated R350 R951 Primary communication path restore (Ethernet)**
0019 GSM module shut down E350 C952 Secondary communication path failure (GSM)**
0400 internal device Power-on reset R350 C952 Secondary communication path restore (GSM)**
E355 C000 Module lost ECP communication with control
** reports only if IP and GSM enabled
R355 C000 Module restore ECP communication with control
E353 C103 Long range transmitter fault trouble
R353 C103 Long range transmitter fault restore

– 12 –
Using ∗29 Menu Mode to Program IP/GSM Options Keypad Address (for Remote Access)
This prompt appears if remote access is enabled.
Entering ∗29 Program Mode
For enhanced remote access features, choose an AUI address. If no AUI
Press ∗29 while in Data Field Programming mode. addresses are available (all four AUIs are being used), choose an available
The following prompts appear. standard keypad address (some remote access features will be unavailable).
Enable INT IP/GSM? 1, 2, 5, 6 = emulated AUI address
0 = No, not using either IP or GSM; 1 = Yes, using IP and/or GSM module 17-23 = emulated standard keypad address
[∗] to continue. NOTE: Default = 1 (IP and/or GSM) NOTE: An AUI or standard keypad address is required for remote access
purposes, but an actual AUI device or keypad is not used.
IMPORTANT: If using an external communication device, see the VISTA-GSM
Module Installation section of the Installation and Setup Guide (Inadequate Supervision
Signal Strength paragraph) for physical installation of an external The supervising station must hear from the IP/GSM at least once during the
communication device. When complete, enter 1 at this prompt and enter 1-Prog supervision period. AlarmNet transmits a communications failure alarm to the
at the next prompt. Then program and register the external device using the central station if the supervision message is not received within the period.
Installation and Setup Guide included with the external communication device. This selection sets the supervision timing for one of the following values:
Programming/Diagnostics Select if using IP and/or GSM if using IP only (not for GSM usage)
• 30 day • US UL Line (6 Min)
1= Prog (program the IP/GSM options)
• 24-hours • US UL Line (90 Sec)
2 = Diag (enter diagnostic mode)
0 = Quit; returns to data field programming mode • None (no supervision) • CN UL Line Lv1 3 (3 Min)
• CN UL Line Lv1 4 (90 Sec)
Internal Device Programming Prompts • CN UL Line Lv1 5 (75 Sec)
The keys used to select and enter options now follow 7720P keypad emulation. • 1 hour
Refer to the table on the previous page for detailed key functions. The following To scroll the choices: [∗] key scrolls forward; [backspace] key scrolls backward
is a summary: [#] to continue
[∗] = scroll the options of a particular prompt GSM Rollover Y/N
[#] = accept the entry and move to the next prompt
Appears only if IP&GSM is selected as Internal Device option.
[A] = backspace or shift-[A} for escape
[Y] = all messages (including AlarmNet network supervisory messages) are
[B] = scroll to next prompt or shift-[B] scroll to previous prompt
sent over the GSM network in the event of an Internet failure
[C] = answer No or shift-[C] answer Yes to prompt
[N] = all messages (except AlarmNet network supervisory messages) are sent
[D] = shift key
automatically over the GSM network in the event of an Internet failure
Internal Device Selection GSM 24Hr Tst Y/N
Select the type of IP and/or GSM module usage (press [∗] to scroll choices): Appears only if IP&GSM is selected as Internal Device option.
Disabled (none); IP only; GSM module only; IP & GSM [Y] = have a message sent once a day to verify GSM operation. A "secondary
[#] to continue communication path loss" message is generated if the message is not
NOTE IF USING GSM ONLY OPTION: For registration purposes, the internal successfully delivered.
device must first be set for IP & GSM (and the control must be connected to [N] = disable 24hr test
the Internet via the RJ45 connector). Follow the prompts to program
appropriate values and use the default settings for the IP specific prompts. Old Alarm Time
After the control is registered (see Registering the Control with AlarmNet The old alarm time sets how long an undeliverable alarm is retried for delivery
paragraph later in this section), return to this prompt and set for GSM only. to AlarmNet. If the message is not validated, it is retried until the old alarm time
is reached or the message is validated. The choices available are:
Multi-Mode (email reporting) • 10 Minutes • 4 Hours
This feature is available only after authorization for it is set via the web-based • 15 Minutes • 8 Hours
programming tool on the AlarmNet Direct website. • 30 Minutes • 12 Hours
Multi-mode emulates 4204 Relay Module outputs to send up to four (4204 • 1 Hour • 24 Hours
sourced) or up to eight (2-4204 sourced) reports of system events to the user via • 2 Hours
email (email address is entered at the AlarmNet Direct website). Use the To scroll the choices: [∗] key scrolls forward; [backspace] key scrolls backward
AlarmNet Direct website to customize event titles, if desired. If enabled, a multi- [#] to continue
mode address must be entered in the next prompt.
Use *79/*80 Menu modes to program each emulated output to trigger a desired IP Fault Time
system event that, upon occurrence, will be sent to the user’s email address. Appears only if IP or IP&GSM is selected as Internal Device option.
Select the desired multi mode option: 01-99 = time delay (in minutes) before the control notifies the central station that
Disabled = no email reporting of events there is a loss of contact with the network over the Ethernet (IP)
4204 Sourced = up to four types of events reported (relay numbers 1-4 report connection.
as events 1-4 respectively) 0 = no delay (valid only If using IP only)
2-4204 Sourced = up to eight types of events reported (first module’s relay Must be two (2) minutes for UL installations.
numbers 1-4 report as events 1-4 respectively; second GSM Flt Time
module’s relay numbers 1-4 report as events 5-8 respectively) Appears only if GSM or IP&GSM is selected as Internal Device option.
To scroll the choices: [∗] key scrolls forward; [backspace] key scrolls backward 01-99 = time delay (in minutes) before the control notifies the central station
[#] to continue that a loss of contact with AlarmNet network has occurred.
NOTES: 0 = no delay (valid only if using GSM only,
1. Multi-mode has not been evaluated by UL. Must be two (2) minutes for UL installations.
2. Multi-mode (email notification) is intended as a convenience for the user,
and does not replace Central Station reporting of critical events (alarms, Notify Panel Of _
troubles, etc.). Appears only if IP&GSM is selected as Internal Device option.
Select from the following choices:
Multi-Mode Address • Neither Fault
This prompt appears if Multi Mode is enabled. • Both IP and GSM must fail before fault code is sent (status code 4005
12-15 =emulated 4204 Relay Module address. displayed); panel receives primary and secondary path failure messages.
If using “2-4204-sourced,” the address of the second module is automatically No message sent if only one or the other path fails.
assigned an address one higher than the first module’s address. To scroll the choices: [∗] key scrolls forward; [backspace] key scrolls backward
NOTE: A 4204 Relay module address is required for multi-mode purposes, but [#] to continue
an actual 4204 Relay module is not used.
NOTE: IP failure will always be sent to the central station as Primary Path
Primary City ID Failure, and GSM failure will always be sent as Secondary Path Failure.
NOTE: Account information is provided by the central station administrator.
01-99 (decimal) = 2-digit primary city code IP address information prompts
The following prompts appear only if IP or IP&GSM is selected as Internal
Primary CS ID Device.
Enter the primary central station's system ID number, 01-FE (HEX) It is recommended to use dynamically allocated IP addresses, but if fixed IP
Primary Sub ID addresses are desired, contact your network administrator for the appropriate
Enter the 4-digit customer account number, 0001-9999 (decimal). information. Note that a valid IP address must be entered in each prompt before
the system continues to the next prompt. Entries cannot be left with the default
Remote Access values.
This feature is available only after authorization for it is set via the web-based
programming tool on the AlarmNet Direct website. Use DHCP
[Y] = have the IP addresses dynamically allocated (recommended), skip to
Remote Services allow the end user to access their security system from a
Review prompt.
computer via the remote services website. Most system functions can then be
[N] = use fixed IP addresses; continue with next prompt
performed.
[#] to continue
[Y] = use remote services
[N] = do not use remote services
[#] to continue
– 13 –
NIC IP Address [255.255.255.255] IP/GSM Diagnostic Commands (continued)
Enter the 4-part IP address for this device, separating each part with a space Key Prompt Function
([∗] key, displayed as periods). [#] to continue [C] Time
Mon 01 Jan 2006
Retrieves the current date and
Subnet Mask [255.255.255.255] 05:48:39 am time from the AlarmNet network
Enter the 32-bit address mask used to indicate the portion (bits) of the IP
in Greenwich Mean Time (GMT).
address that is being used for the subnet address, separating each part with a
This display confirms that the
space ([∗] key, displayed as periods). [#] to continue module is in sync with network.
Gateway IP Addr [255.255.255.255] Physical Link
Enter the 4-part IP address assigned to the Gateway, separating each part with [D] Physical Link
Only if IP or IP/GSM enabled.
a space ([∗] key, displayed as periods). If unused set to 0.0.0.0. Good/Bad Indicates whether the device has
[#] to continue detected a physical connection
DNS IP Addr [255.255.255.255] to the internet.
Enter the 4-part IP address assigned to the DNS (Domain Name System) [∗] to continue to NIC IP address.
server, separating each part with a space ([∗] key, displayed as periods). If IP Information Displays
unused set to 0.0.0.0. [#] to continue NIC IP Address
Displays the IP address
xxx.xxx.xxx.xxx assigned to this device.
Review? (and Exit ∗29 Menu mode or Reset Defaults)
[∗] to continue to subnet mask.
You can review the ∗29 Menu mode options to ensure that the correct entries
have been made. When satisfied, select [N] to exit ∗29 Menu mode. Displays the 32-bit address mask
Subnet Mask used to indicate the portion (bits)
To review prompts or exit ∗29 Menu mode: xxx.xxx.xxx.xxx
[Y] = review prompts and entries, starting with Internal Device. Use the of the IP Address that is being
up/down arrow keys to scroll through the program fields without changing used for the subnet address.
any of the values. If a value requires change, simply type in the correct [∗] to continue to gateway IP.
value. When the last field is displayed, the “REVIEW?” prompt appears. Displays the IP Address
[N] = Exit *29 menu mode and return to data field programming mode. The Gateway IP Addr assigned to the Gateway.
prompt briefly displays “DONE” before returning to data field mode xxx.xxx.xxx.xxx [∗] to continue to DNS server IP.
prompt “Enter ∗ or #.”
Displays the IP Address
[#] to accept Y or N selection (# alone exits same as N) DNS Serv IP assigned to the DNS (Domain
To reset ∗29 Menu mode defaults: xxx.xxx.xxx.xxx Name System) server.
Press [ESC] at the Review prompt to display the “Set Defaults” prompt. [∗] to continue to encryption test.
[Y] = reset ∗29 menu mode options to factory values; if selected, all
Performs a self-test of the AES
programmed ∗29 Menu mode options are reset to the factory settings Encryption Test encryption algorithm.
[N] = cancel reset defaults function AES Passed! [∗] to continue to DHCP.
Programming IP/GSM Options via AlarmNet Direct Website DHCP (Dynamic Host
To program the IP/GSM options via the AlarmNet Direct website (if you are
DHCP
OK Configuration Protocol)
already signed up for this service), go to: indicates server is performing
https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx satisfactorily.
If you are not signed up for this service, click on “Dealer Sign-Up. [∗] returns to Physical Link prompt.
Log in and follow the on-screen prompts.
Please have the following information available: PriRSSI GPRS REG GSM Status Displays
1. Primary City ID (two-digit number) [E] Only if GSM or IP/GSM enabled.
2. Primary Central Station ID (two-digit hexadecimal number)
-xxxdbm x x PriRSSI – Primary Site RSSI
3. Primary Subscriber ID (four-digit number) level in dbm
4. MAC ID and MAC CRC number (located on the outside of box and on label GPRS – GPRS Service
inside module) or MIN number of the device you are replacing availability where “x” can be:
5. Mode of operation of existing module if replacing a "C" series radio. “Y” if GPRS is available
After programming is complete, you must transfer the data to the module and the “N” if GPRS is Not available
module must be registered. Refer to the Registration section for details. REG – Registration status
from GSM module where
∗29 Menu Mode)
IP/GSM Diagnostic Commands (∗ “x” can be:
Diagnostic commands can be used to quickly view your Internet and GSM N – Not Registered
connectivity settings and options. For each command press the [shift] key and H – Registered Home
then the designated command key. For example, press [shift] then [1/A] to S – Searching
display the software revision screen. D – Registration Denied
To enter Diagnostic mode: R – Registered Roaming
1. Press ∗29 while in data field programming mode. ? – Unknown Reg. State
2. Enter “1” at the “Enable IP/GSM” prompt then press [∗]. [∗] to continue to next screen.
3. Select “2” (Diag) at the next prompt. Cntry – Country Code
4. Enter the desired command at the “Sel Key Command” prompt. Cntry Netw LAC Netw – Network Code
For subsequent commands, enter the next command at the current screen. xxx xxx xxxxx LAC – Reg. status from GSM.
To exit Diagnostic mode, press ESC (shift-[A]). [∗] to continue to next screen.
Key Prompt Function Cell – Base Station ID
Cell BaseSt Chan BaseSt – Base Station Antenna
[A] Software Revision
Internal IP/GSM "x.x.xx" indicates the installed
Xxxxx x xxx Sector
x.x.xx mm/dd/yy software Revision. Mm/dd/yy Chan – Control Channel in use
indicates month, day and year of [∗] to continue to next screen.
the revision. Secondary GSM Site RSSI level
Second Site RSSI in dbm.
[B] MAC Address
MAC xxxxxxxxxxxx “xxxxxxxxxxxx” indicates the -xxxdbm [∗] to continue to next screen.
MAC CRC yyyy IP/GSM’s unique identification
[F] Testing Gateway Network Diagnostic Test
number. Yyyy indicates the 4
Only if IP or IP/GSM enabled.
digit MAC CRC needed to enroll Redir 1 Performs a set of network
the device in dealer direct.
diagnostics that tests the
[∗] to continue to SCID. integrity of the links between the
SCID Display IP/GSM and the various
SCID xxxxx xxxxx Only if GSM or IP/GSM enabled. connection points (Redirs) to
xxxxx xxxxx Displays the identification AlarmNet.
number assigned to the SIM
[S] ECP FLT Status request
card (SCID) in this device.
OK = normal
[∗] to continue to IMEI. OK i = IP off line
IMEI Display I = IP fault reported
IMEI xxxxxxxx Only if GSM or IP/GSM enabled. g = GSM off line
Xxxxxx x Displays the identification G = GSM fault reported
number assigned to the GSM
module in this device.
[∗] returns to MAC Address.

– 14 –
IP/GSM Diagnostic Commands (continued) Registration with AlarmNet
Key Prompt Function
The control must be registered with AlarmNet before internet communication
[T] Test Msg Sent Test Alarm (via IP or GSM) can occur.
Sends a Test alarm to AlarmNet. To register, the control must be connected to the Internet.
Functional for a registered Register the control by using one of these methods:
IP/GSM only. If the device is not
Register by phone
registered, a message is
1. Call 1-800-222-6525
displayed indicating that the
You will need the following information:
command cannot be executed.
• MAC ID and MAC CRC number (found on the PCB label).
[X] Reset CPU Y/N Reset the IP/GSM. • Subscriber information (provided by the central station), including a
[N] = return to diagnostic mode city code, CSID, and a subscriber ID.
(blank screen = enter next 2. When instructed to do so, triple-click the Test switch to complete the
command or escape). registration.
[Y] = resets the module (blank
screen = when reset Register with Alpha Keypad using *29 Menu mode
complete, enter next 1. Enter *29 Menu mode, select Diagnostic mode, then press Shift then [↑]
command or escape). key (D key followed by the B key). The registration message is sent
(“Registering” displayed) and the control waits for the acknowledgment.
↑]
[↑ Registration (Shift-UP 2. “Registration SUCCESS” displayed, indicating successful registration.
Registering … arrow)
Registers a programmed Register with Test Switch on control’s PCB (triple-click)
IP/GSM with AlarmNet. If it is 1. Click the switch three times.
configured to report to AlarmNet, 2. Watch the GSM Status LEDs: The Message (yellow) LED and the
the IP/GSM will register with Status (green) LED will blink slowly in unison while registration is in
AlarmNet. progress.
3. When registration is complete, the Status (green) LED goes out.
↓]
[↓ Enter PIN# Registration with PIN for
Replacement Module (DN Register with AlarmNet Direct Website
To register via AlarmNet Direct Website, please go to:
arrow) https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx.
Registers a programmed
IP/GSM with AlarmNet if it is Log in and follow the on-screen prompts.
configured to report to AlarmNet. Please have the following information available:
[0] Force Upload of • Primary City ID (two-digit number provided by central station)
Force Server Update
Configuration File to Server • Primary Central Station ID (two-digit hexadecimal number provided by
Y/N central station)
[Y] = force the device to upload
its entire configuration file • Primary Subscriber ID (four-digit number provided by central station)
to the server. • MAC ID and MAC CRC number (located on outside of box and on label
[N] = cancel the operation. on control’s PC board).
NOTE: If the internet is not If you are not signed up for this service, click on “Dealer Signup” from the
available, and the module is not login screen to gain access to the Honeywell web-based programming.
initialized when you enter this Dealer Sign-Up Direct Link:
command, the following screen
https://services.alarmnet.com/AlarmNetDirectP_Sign-Up.
will be displayed:
Cannot Upload You will be instructed how to proceed upon completing the sign-up form.
Try Later! _ Only one sign-up per dealer is required. Once an initial user is established,
Wait for the RSSI LEDs to light, additional logins may be created by that user.
indicating initialization is Once the control is registered, you may log out of the AlarmNet Direct
complete, and try again. website.

IP/GSM LED Functions


IP (web) Network LED Functions
LED Color LED Description
Top Green Ethernet Link/Activity ON – link is active; OFF – no link
Middle Green Link Speed ON – 100 MB/S; OFF – 10 MB/S
Yellow Network Collision BLINK – collision detected; OFF – normal

IP/GSM Status LED Functions


LED Color LED Description
Green Status ON – control is NOT registered with AlarmNet; OFF – control is registered with AlarmNet.
FAST BLINK – Download session with Compass in progress.
SLOW BLINK – In unison with yellow LED – Registration in progress.
Yellow Message ON – Message transmission pending.
QUICK PERIODIC BLINK - Normal
FAST BLINK – Message waiting for network ACK.
SLOW BLINK – In unison with green LED – Registration in progress.
Red Fault ON – No contact with network; OFF– Normal.
SLOW BLINK – Loss of communication with the panel (ECP fault).
FAST BLINK – No network contact AND loss of communication with the panel.
All FAST BLINK – In unison with the RSSI Bar Graph LEDs – Hardware Error. Call the
AlarmNet Technical Assistance Center.

Signal Strength and Status LED Meanings


Color Label Indication
Red RSSI ON = signal strength (RSSI) display
OFF = status display
Yel (2) mode OFF = module operating in ECPmode
Green Web web connection status
ON = connected to web
OFF = no web connection
Green GPRS GPRS service availability
ON = GPRS service available
FLASH = GPRS in use
OFF = no GPRS service (messages sent via SMS)
Green GSM network carrier registration status
ON = registered with network carrier, no second site available
FLASH = registered with network carrier and second site available, excellent RSSI
BLINK = registered with network carrier and second site available, acceptable RSSI
SLOW BLINK = registered with network carrier and second site available, low RSSI
OFF = control not registered with network carrier

– 15 –
Setting Schedules (Installer Code + [#] + [6] [4])
NOTES: GROUP NUMBER ( for event 2 user access)
• The master code can only access schedules 01-16 and events 00-07. 1-8; [∗] to continue.
• System clock must be set before schedules can be used. PARTITION ( for events 3-7,10,12)
• Programmed schedules do not take effect until the next scheduled “start” 0 = all partitions; 1 = partition 1; 2 = partition 2; 3 = common
time. (e.g., if programming a schedule time window for 8AM to 5PM, the [∗] to continue.
schedule does not take effect until 8AM after the schedule has been
programmed.) START
01-12 = hour; 00-59 = minute; 0 = AM; 1 = PM; to select days, position the
ENTER SCHED NO. cursor under the desired days using the [∗] key to move forward, then press
01-16 = end-user schedules; 17-32 = installer-only schedules “1” to select the day.
[∗] to continue. [∗] to continue.
To Quit, enter 00.
STOP (for events 1 relay on/off; 2 user access; 3 latch key report)
ENTER EVENT
See START for entries. [∗] to continue.
00 = clear event
01 = Relay On/Off REPEAT
02 = User Access 0 = do not repeat; 1 = repeat schedule weekly; 2 = repeat schedule biweekly
03 = Latch Key Report to Pager (sent to all pagers in the user’s partition; (every other week); 3 = repeat schedule every third week; 4 = repeat
message sent is 777-7777. User must be enabled for paging and schedule every fourth week (28 days)
system must be armed before reporting can occur.) [∗] to continue
04 = Forced Stay Arming (Forced bypass is automatically enabled
regardless of setting in field *23) RANDOMIZE (for events 01 and 11)
05 = Forced Away Arming (Forced bypass is automatically enabled 0 = no; 1 = yes
regardless of setting in field *23) If selected, the scheduled start and stop times will vary within 60 minutes of
06 = Auto Disarm the “hour” time. For example, if a schedule is set to start at 6:15pm, it will do
07 = Display “Reminder” so the first time 6:15pm arrives, but on subsequent days it will start anytime
10 = Display custom words (if selected, system displays custom words 8, 9, between 6:00 and 6:59 p.m.
and 10 at defined time. Can be used as installer’s reminder message NOTE: Do not use the random option if the start and stop times are within
to the end user); programmable by installer only the same “hour” setting, otherwise unpredictable results may occur (e.g., the
11 = Periodic Test Report (see key commands in Test Report Code, data randomized stop time may occur before the start time).
field *64, to quickly set periodic test reporting intervals); programmable [∗] to continue and return to ENTER SCHED NO. prompt to program the
by installer only next schedule.
[∗] to continue.
DEVICE NUMBER ( for event 1 relay on/off)
01-18; [∗] to continue.

Setting The Real-Time Clock


The Real-Time Clock must be set before completing the installation.
NOTE: All partitions must be disarmed before the Real-Time Clock can be set.
1. Master Code + [#] + [6] [3]
2. Press [∗] when the time/date is displayed. A cursor appears under the first digit of the hour.
To move cursor ahead, press [∗]. To go back, press [#].
• Enter the 2-digit hour setting, followed by the 2-digit minute setting, then press [1] for PM or [2] for AM.
• Enter the last two digits of the current year, followed by the 2-digit month setting and the 2-digit day setting.
3. To exit, press [∗] when cursor is at the last digit, or wait 30 seconds.

Uploading/Downloading Via The Internet


This control supports upload/download programming capability via the Internet by using the AlarmNet network and Compass
downloading software. The control must be connected to the Internet (via the on-board RJ45 connector or VISTA-GSM module),
have all IP features programmed (∗29 Menu mode), and be registered with AlarmNet.
The following is required at the Downloading Office:
• Broadband Internet Access and Broadband (Cable/DSL) Modem
• Broadband (Cable/DSL) Router (optional, if connecting more than one device to the Internet)
• Computer running Compass Downloading Software version that supports Internet upload/download for this control.

To perform upload/download functions:


1. Connect the computer to the Internet and start the Compass downloading software.
2. Open the control’s account, then select the Communications function and click the Connect button.
3. At the Connect screen, check that the control’s MAC address is entered and the TCP/IP checkbox is checked.
4. Click Connect. The Internet connection to the control is made automatically via AlarmNet.
5. Once connected, use the Compass downloading software as normal to perform upload/download functions.

– 16 –
SCHEDULES WORKSHEET(installer code + [#] + [6] [4]; master code can only access schedules 01-16 and events 00-07
No. Event Device No. Group No. Partition Start Time/ Stop Time/ Repeat Random
(see list below) for “01” events: for “02” events: for “04-06” events: Days Days (1-4) (yes/no)
enter 01-18 enter 1-8 enter 1, 2, or 3
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Events: Master/Installer Installer Only
00 = clear event 04 = forced STAY arm 10 = display custom words 8-10
01 = device on/off 05 = forced AWAY arm 11 = periodic test report
02 = user access 06 = auto disarm
03 = latch key report 07 = display “reminder”
Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat every fourth week (28 days)

– 17 –
*56 ZONE PROGRAMMING WORKSHEET [default shown in brackets]
Zone Zn Type Part. Report Hardwire Rsp. Time Location
Type
1 [09] [1] [EOL] [1]
2 [01] [1] [EOL] [1]
3 [03] [1] [EOL] [1]
4 [03] [1] [EOL] [1]
5 [03] [1] [EOL] [1]
6 [03] [1] [EOL] [1]
7 [03] [1] [EOL] [1]
8 [03] [1] [EOL] [1]
Zone Zn Type Part. Report Input Type Loop Serial No. Location
9 [1] [RF]
10 [1] [RF]
11 [1] [RF]
12 [1] [RF]
13 [1] [RF]
14 [1] [RF]
15 [1] [RF]
16 [1] [RF]
17 [1] [RF]
18 [1] [RF]
19 [1] [RF]
20 [1] [RF]
21 [1] [RF]
22 [1] [RF]
NOTES: 23 [1] [RF]
Zone Type: see chart in 24 [1] [RF]
∗56 Zone Programming 25 [1] [RF]
Menu mode section. 26 [1] [RF]
Report Code: enabled if 27 [1] [RF]
any digit entered as 1st 28 [1] [RF]
digit; 29 [1] [RF]
Hardwire Type (zns 2-8): 30 [1] [RF]
0 = EOL 3 = ZD 31 [1] [RF]
1 = NC 4 = DB
32 [1] [RF]
2 = NO
33 [1] [RF]
Input Type: 34 [1] [RF]
2 = AW (zones 9-48)
3 = RF (zones 9-48) 35 [1] [RF]
4 = UR (zones 9-48) 36 [1] [RF]
5 = BR (zones 49-64) 37 [1] [RF]
NOTE: Zones 9-16 not 38 [1] [RF]
available if zone
doubling enabled. 39 [1] [RF]
40 [1] [RF]
Response Time:
41 [1] [RF]
0 = 10msec
1 = 350msec 42 [1] [RF]
2 = 700msec 43 [1] [RF]
3 = 1.2 sec 44 [1] [RF]
45 [1] [RF]
Reserved Zones 46 [1] [RF]
91 = addressable device 47 [1] [RF]
report enable/disable 48 [1] [RF]
default zone type = 49 [1] [BR]
[05].
50 [1] [BR]
92 = Duress report 51 [1] [BR]
enable/disable [1] [BR]
52
53 [1] [BR]
54 [1] [BR]
55 [1] [BR]
56 [1] [BR]
57 [1] [BR]
58 [1] [BR]
59 [1] [BR]
60 [1] [BR]
61 [1] [BR]
62 [1] [BR]
63 [1] [BR]
64 [1] [BR]
95 [00] N/A** N/A N/A N/A keypad [1] / [∗]
96 [00] N/A** N/A N/A N/A keypad [3] / [#]
99 [06] N/A** N/A N/A N/A keypad [∗] / [#]
** Emergency key zones 95, 96, and 99 report the partition of the keypad used to activate the emergency zones.

– 18 –
*57 FUNCTION KEY WORKSHEET
A B C D Comments
Option Function P1 P2 com P1 P2 com P1 P2 com P1 P2 com
01 Paging
02 Time Display
03 Arm AWAY
04 Arm STAY
05 Arm NIGHT-STAY
06 Step Arming
07 Device Activation Device:
08 Comm. Test
09 Macro Key 1 Assign each macro key to only a single partition. †
10 Macro Key 2 Assign each macro key to only a single partition. †
11 Macro Key 3 Assign each macro key to only a single partition. †
12 Macro Key 4 Assign each macro key to only a single partition. †
00 Emergency Keys: zone 95 zone 99 zone 96 paging
Personal Emergency n/a
Silent Alarm n/a
Audible Alarm n/a
Fire n/a
Emergency Keys: A = paired keys [1] / [∗] (zone 95); B = paired keys [∗] / [#] (zone 99); C = paired keys [3] / [#] (zone 96)
† There are only four macros system-wide.

OUTPUT RELAYS/POWERLINE CARRIER (X-10) DEVICES WORKSHEET FOR ∗79, ∗80 and ∗81.
Applicable only if Relays and/or Powerline Carrier Devices are to be used.
∗79 RELAY/POWERLINE CARRIER (X-10) DEVICE MAPPING (Must program before using *80)
OUTPUT TYPE OUTPUT TYPE
Relay X10 Relay X10
Output Module Pos Unit Output Module Pos Unit
No. Addr. (1-4) No. Description No. Addr. (1-4) No. Description
01 09
02 10
03 11
04 12
05 13
06 14
07 15
08 16
17 On-Board Trigger 1 norm output =
18 On-Board Trigger 2 norm output =

✱81 ZONE LISTS WORKSHEET


Fill in the required data on the worksheet below and follow the procedure in the installation manual as you enter the
data during the displays and prompts that appear in sequence.
NOTE: Record desired zone numbers below, noting that a list may include any or all of system's zone numbers.
List No. Used For… Contains These Zones…
01 General Purpose (GP)
02 General Purpose
03 Chime-by-Zone or GP (see field *26 for Chime-by-Zone option)
04 Cross Zones or GP (see field *85 for Cross Zone Timer option)
05 Night-Stay Zones or GP
06 Dial Delay Disable or GP V21iPSIA: see field *50 for Dial Delay Disable option
07 Unlimited Reports or GP V21iPSIA: see field *93 for Unlimited Reports option
08 General Purpose
09 Zones activating pager 1
10 Zones activating pager 2
11 Zones activating pager 3
12 Zones activating pager 4

– 19 –
✱80 OUTPUT DEFINITIONS
Fill in the required data on the worksheet below and follow the programming procedure in the installation manual as you
enter the data during the displays and prompts that appear in sequence.
Notes: 1. For Relays, 4229 and 4204 devices are programmed in *79, *80, and *81 modes.
2. For Powerline Carrier devices (plcd), field ✱27 must be programmed with a House Code.
3. Tampers of expansion units cannot be used to operate devices.
Output Activation Type and Detail Partition Event (for zone list/activated by) Action Output Device
Function Activated by Zone List Zone Type Zone No. Number By Zone List By Zone No. 0 = off Number Type
Number 0=delete (ZL) (ZT) (ZN) (P) 1 = close 2 secs
(1-48) 1=zn list 1-8 = list (see table 00=none (if using ZT trig) 0 = restore 0 = restore 2 = stay closed 1-18 R = relay
2=zn type below) 01-64 0 = any 1 = alarm 1 = alrm/flt/trbl 3 = pulse T = trigger
3=zn no. 1 = partition 1 2 = fault 4 = toggle X = X10
2 = partition 2 3 = trouble 5 = duration 1††
3 = common 6 = duration 2††
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

ZONE TYPE/SYSTEM OPERATION – Choices for Zone Types are:


00 = Not Used 05 = Trouble Day/Alarm Night 10 = Interior w/Delay 24 = Silent Burglary
01 = Entry/Exit#1 06 = 24 Hr Silent 12 = Monitor Zone 77 = Keyswitch
02 = Entry/Exit#2 07 = 24 Hr Audible 14 = Carbon Monoxide 81 = AAV Monitor Zone
03 = Perimeter 08 = 24 Hr Aux 16 = Fire w/Verification 90-91 = Configurable
04 = Interior Follower 09 = Fire 23 = No Alarm Response
Choices for System Operation are: Note: In normal operation mode:
20 = Arming–Stay 38 = Chime 52 = Kissoff
21 = Arming–Away 39 = Any Fire Alarm 54 = Fire Zone Reset Code + # + 7 + NN Key Entry starts Device
22 = Disarming (Code + OFF) 40 = Bypassing 58 = Duress Code + # + 8 + NN Key Entry stops Device
31 = End of Exit Time 41 = **AC Power Failure 60 = AAV Trigger
32 = Start of Entry Time 42 = **System Battery Low 66 = Function key† ** Use 0 (any) for Partition No. (P) entry.
33 = Any Burglary Alarm 43 = Communication Failure 67 = Bell Failure *** Or at Disarming, whichever occurs earlier.
36 = **At Bell Timeout*** 68 = TELCO Line Fault † Use *57 Menu mode to assign the function key.
78 = Keyswitch red LED††† †† Duration is set in program field *177.
79 = Keyswitch green LED††† ††† Device action not used for these choices.

– 20 –
5800 Series Transmitter Input Loop Identification
All of the transmitters illustrated have one or more unique factory assigned input (loop) ID numbers. Each of the inputs requires its own
programming zone (e.g., a 5804's four inputs require four programming zones).
For information on any transmitter not shown, refer to the instructions accompanying that transmitter for details regarding loop numbers, etc.

UL NOTE: The following transmitters are not intended for use in UL installations: 5802MN, 5802MN2, 5804, 5804BD, 5814, 5816TEMP,
5819, 5819WHS & BRS, and 5850.
The 5827BD and 5800TM can be used in UL Listed Residential Burglar installations.

LOOP 3
LOOP 4
YOU MUST
ENROLL LOOP 2
THIS LOOP 1
LOOP BUTTON
1 LOOP 1
LOOP 1
LOOP LOOP 1
1

5800CO 5800Micra 5800SS1 5 8 0 0 WAV E 5801 5802 MN


ENROLL AS "RF" ENROLL AS "RF" E N RO L L A S " R F " SET HOUSE ID E N RO L L A S ENROLL AS
E N RO L L A S " R F " "UR OR"RF" "UR" OR "RF"

LOOP 3
LOOP 2 SERIAL #1
LOOP 4 LOOP 3
YOU MUST ON LOOP 4 SERIAL #1
ENROLL
OFF
LOOP 2 YOU MUST ON
OF LOOP 2 LOOP 1 LOOP 1
F
THIS LOOP 1 ENROLL SERIAL #1 1
2

LOOP 1 BUTTON THIS LOOP 4


LOOP SERIAL #1
BUTTON 3
LOOP 1
3 ••

SERIAL #2 4

•• •
LOOP 3

••• ••••
••
• •• LOOP 1 SERIAL #2
LOOP 2
SERIAL #2 - LOOP 1 = ON + 4 BUTTONS
LOOP 4 = 3 + 4 BUTTONS
5802 MN2 5804/5804E 5 8 0 4 B D / 5 8 0 4 B DV 5805-6 5806/5806W3 5809
ENROLL AS ENROLL AS "BR" ENROLL AS "BR" ENROLL AS "BR" 5808/5808LST/5808W3 ENROLL AS "RF"
"UR" OR "RF" SET HOUSE ID ENROLL AS "RF"

LOOP 2
(REED) LOOP 1
LOOP 2 (PRIMARY)
LOOP 1 (REED) LOOP 1
LOOP 2 LOOP 2 LOOP 2
(TERMINALS) (REED)
(REED) LOOP 1 (AUX.
(TERMINALS) LOOP 1 CENTER)
LOOP 1
(TERMINALS)
ALTERNATE LOOP 3
POSITION FOR (AUX.
LOOP 2 RIGHT)

5814 5815 5816 5816MN 5817 5818MNL


ENROLL AS "RF" ENROLL AS "RF" ENROLL AS "RF" ENROLL AS "RF" ENROLL AS "RF" ENROLL AS "RF"

LOOP 2 LOOP 2
(REED) (REED) AR
ME
D

RE
AD
Y

LOOP 3 LOOPS MIC LOOP


LOOP 1 MESSA
GE
1
(TERMINALS) LOOP 1 1-3
(INTERNAL
LOOP 1 SHOCK
LOOP 3 (TERMINALS) SENSOR
(TERMINALS)

5819 5819S (WHS & BRS) 5820/5820L 5821 5828/5828V 5853


ENROLL AS "RF" ENROLL AS "RF" ENROLL AS "RF" ENROLL AS "RF" SET HOUSE ID ENROLL AS "RF"

SERIAL #1
LOOP 3
AW
AY SERIAL #1
SERIAL #1 ST
AY LOOP 2
LOOP 4 1

2
LOOP 1 LOOP 1
SERIAL #1 (MOTION) LOOP 1
SERIAL #2 3

4 LOOP 1
LOOP 3
SERIAL #2
LOOP 2
SERIAL #2 - LOOP 1 = ON + 4 BUTTONS
LOOP 4 = 3 + 4 BUTTONS

5878 5890/5890PI 5894PI 5897-35


ENROLL AS "BR" ENROLL AS "RF" ENROLL AS "RF" ENROLL AS "RF" 5800-003-V0

– 21 –
UL NOTICES
1. Entry Delay No. 1 and No. 2 (fields ∗35, ∗36) cannot be greater than 30 seconds for UL Residential Burglar Alarm
installations, and entry delay plus dial delay should not exceed 1 minute. For UL Commercial Burglar Alarm
installations, total entry delay may not exceed 45 seconds.
2. For UL Commercial Burglar Alarm and UL Residential Burglar Alarm installations with line security, total exit delay
time must not exceed 60 seconds. For UL Burglar Alarm installations without line security, total exit delay time
must not exceed 120 seconds.
3. The maximum number of reports per armed period (field ∗93) must be set to “0” (unlimited) for UL installations.
4. Periodic testing (see scheduling mode) must be at least every 24 hours.
5. Alarm Sounder plus Auxiliary Power currents must not exceed 600mA total for UL installations (Aux power 500mA
max.).
6. All partitions must be owned and managed by the same person(s).
7. All partitions must be part of one building at one street address.
8. If used, the audible alarm device(s) must be placed where it/they can be heard by all partitions.
9. For UL commercial burglar alarm installations the control unit must be protected from unauthorized access. The
tamper switch installed to protect the control unit enclosure door is suitable for this purpose.
10. Remote downloading without an alarm company technician on-site (unattended downloading) is not permissible
for UL installations.
11. Auto-disarming is not a UL Listed feature.
12. As SIA limits for delay of alarm reporting and sounding can exceed UL limits for commercial and residential
applications, the following UL requirements per UL681 are provided:
The maximum time that a control unit shall be programmed to delay the transmission of a signal to a remote
monitoring location, or to delay the energizing of a local alarm sounding device to permit the alarm system user to
enter and disarm the system, or to arm the system and exit shall not exceed:
a) 60 seconds for a system with standard line security or encrypted line security,
b) 120 seconds for a system without standard line security or encrypted line security, or
c) 120 seconds for a system that does not transmit an alarm signal to a remote monitoring location.
13. This control is not intended for bank safe and vault applications.

SIA Quick Reference Guide


1. *31 Single Alarm Sounding per Zone: If “0” selected, “alarm sounding per zone” will be the same as the “number
of reports in armed period” set in field *93 (1 if one report, 2 if 2 reports, unlimited for zones in zone list 7).
2. *34 Exit Delay: Minimum exit delay is 45 seconds.
3. *35/*36 Entry Delay 1 and 2: Minimum entry delay is 30 seconds.
4. *37 Audible Exit Warning: Feature always enabled; field does not exist.
5. *39 Power Up in Previous State: Must be “1,” power up in previous state.
6. *40 PABX Access Code or Call Waiting Disable: If call waiting is used, call waiting disable option in field *91
must be set.
7. *50 Burglary Dial Delay: Delay must be minimum of 30 seconds.
8. *59 Exit Error Alarm Report Code: Always enabled.
9 *68 Cancel Report Code: Default is “code enabled.”
10. *69 Recent Closing Report Code: Always enabled.
11. *91 Option Selection: Exit Delay option should be enabled. If call waiting is used, Call Waiting Disable must be
set to “1” (enabled).
12. *93 No. reports in Armed Period: Must be set for 1 or 2 report pairs.
13. Cross zone timer programming is set in field ∗85; cross zone pairs are assigned in zone list 4 using ∗81 Zone
List mode.
14. Duress code is assigned by using the “add a user code” procedure found in the User Guide. Enable Duress code
reporting by programming zone 92 using ∗56 Zone Programming mode.
15. Fire alarm verification is a built-in system feature when a zone is programmed for zone type 16.

– 22 –
– NOTES –

– 23 –
IP (WEB) GRN ETHERNET LINK/ACTIVITY (ON=YES; OFF=NO) FOR COMPLETE
TO INTERNET RJ45 GSM MODULE (OPTIONAL)
NETWORK GRN LINK SPEED (ON=100 MB/S; OFF=10 MB/S) INFORMATION,
CONNECTION CONNECTOR
LEDs YEL NETWORK COLLISION (BLINK=DETECTED; OFF= NORMAL) SEE INSTRUCTIONS
K14488 OR LATER. CAUTION: ESD SENSITIVE DEVICE
24-HR BATTERY STANDBY REQUIRED FOR IP/GSM STATUS LEDs To guard against static discharge damage while installing this module, briefly touch
FIRE INSTALLATIONS. USE 12V, 17.2AH ALL DEVICES AND

K14488PRV1 7/08 Rev. B


ON GRN STATUS (ON=NOT REGISTERED; OFF = REGISTERED) ACCESSORIES USED IN A a chassis ground point in the Control Panel cabinet to discharge any static buildup.
BATTERY FOR 600mA AUX POWER. SEE INTERNAL
YEL MESSAGE CANADIAN INSTALLATION Avoid performing this installation while standing on a carpeted floor because a
INSTRUCTIONS. IP/GSM
RED FAULT (ON=NO NETWORK CONTACT; BLINK = PANEL FAULT) MUST BE LISTED FOR carpeted floor increases the possibility of static buildup.
BATTERY CAPACITY FOR EMERGENCY OFF JUMPER
BURGLARY STANDBY USE AT LEAST 4 HRS DATA USE IN CANADA
IP/GSM SWITCHES TO
BATTERY FUSE COM 1361X10 STATUS LED INDICATIONS
CHARGING VOLTAGE 13.8VDC. MAXIMUM TRANS
FOR REPLACEMENT, SYNC ON = RSSI RED RSSI OFF = STATUS; ON = RSSI

+12 AUX
GND
OUTPUT 18
(TRIG. 2)

OUTPUT 17
(TRIG. 1)
CHARGING CURRENT 650mA. 3A
USE SAME VALUE TEST STATUS RSSI YEL MODE 1
OFF = ECP MODE
SEALED LEAD-ACID TYPE. (e.g. ADEMCO No. 90-12) LED MINIMUM YEL MODE 2
BATTERY NORMALLY NEED NOT BE INDICATOR LIT GRN WEB OFF = NO WEB CONNECTION; ON = CONNECTED TO WEB
REPLACED FOR AT LEAST 3 YRS. RED JUMPER 12 3 4 5 6 7 8
BATTERY GRN GPRS OFF = NO GPRS SERVICE; FLASH = GPRS IN USE; ON = GPRS AVAILABLE
RED CUT FOR BELL SUPERVISION. 8-PIN CONNECTOR
12V, 4AH FOR 1361X10 TRANS. GRN GSM OFF = NOT REGISTERED w/CARRIER; BLINK/ON = REGISTERED w/NETWORK CARRIER
TO DETERMINE TOTAL STANDBY LOAD ALSO, CONNECT 2000 OHM
(FLYING LEADS FOR

ÊK14488PRV14Š
ON BATTERY, ADD 100mA TO TOTAL OF BLACK RESISTOR DIRECTLY ACROSS AND ON-BOARD TRIGGERS SIGNAL STRENGTH
BATTERY CONNECTION) AND STATUS LEDs
AUX. POWER OUTPUT AND REMOTE SOUNDER. SEE INSTRUCTIONS.
KEYPAD CURRENTS.
AC AC BELL GND AUX GRN YEL Z1+ Z1- GND Z2 Z3 GND Z4 Z5 GND Z6 Z7 GND Z8 TIP RING TIP RING GND
USE UL LISTED LIMITED ENERGY
CABLE FOR ALL CONNECTIONS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
USE 1361X10 TRANSFORMER INTERFACE
IN PLACE OF 1361 OR 1361CN WHEN POWER
LINE CARRIER DEVICES ARE BEING USED.

LO
HI
LO

LO
HI
HI

HI
HI

HI
LO
HI

HI
LO
LO

LO
LO

(SEE INSTRUCTIONS FOR CONNECTIONS) (GREEN) (RED)


(BROWN) (GRAY)
}
}

CLASS 2 PLUG-IN TRANSFORMER


16.5VAC, 40VA – + HANDSET INCOMING
PHONE LINE EARTH

}
(e.g. ADEMCO No. 1361)
(USE No. 1361CN IN CANADA) AUX. POWER TELEPHONE WIRING GROUND
OUTPUT SEE
(VIA RJ31X* JACK AND DIRECT
10.5-13.8VDC INSTRUCTIONS
TO 110VAC CONNECT CORD)
600mA MAX. FOR PROPER
UNSWITCHED OUTLET (24HR) GROUNDING
(500mA MAX. *CA38A IN CANADA DOC LOAD NO.: 3
FOR UL
THIS EQUIPMENT SHOULD BE INSTALLED IN INSTALLATIONS) FOR CONNECTION OF OPTIONAL 4286 VIP MODULES
ACCORDANCE WITH THE NATIONAL FIRE TO PHONE TERMINALS, SEE INSTRUCTIONS.
ZONE 7
ZONE 8

ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6

PROTECTION ASSOCIATION'S + ALL OUTPUTS


STANDARD 72, CHAPTER 2 (NATIONAL ARE POWER WARNING:TO PREVENT RISK OF SHOCK, DISCONNECT

BLACK: KEYPAD GROUND (- ) RETURN


FIRE PROTECTION ASSOCIATION, TELEPHONE LINE AT TELCO JACK BEFORE SERVICING
– LIMITED. 2000 2000
BATTERYMARCH PARK, QUINCY, MA 2000 2000 2000 2000 2000 2000 THIS UNIT.
02169). OHMS OHMS OHMS OHMS OHMS OHMS OHMS OHMS
PRINTED INFORMATION DESCRIBING NOTE: EOLR EOLR EOLR EOLR EOLR EOLR EOLR EOLR
PROPER INSTALLATION, OPERATION, ALARM OUTPUT KEYPAD (S)

GREEN: DATA IN FROM KEYPAD


YELLOW: KEYPAD DATA OUT

BLK
RED: KEYPAD PWR ( + )
TESTING, MAINTENANCE, EVACUATION CURRENT (IN BOTH • MAX LOOP RESISTANCE: (EACH ZONE) 300 OHMS

www.honeywell.com/security
10.5–13.8VDC, 2A MAX. (600mA
4-WIRE SMOKE DETECTOR CONNECTIONS

P.O. Box 9040, Melville, NY 11747


PLANNING AND REPAIR SERVICE IS TO BE PARTITIONS) AND (PLUS EOLR)

2 Corporate Center Drive, Suite 100


MAX. FOR UL USAGE, KEYPADS AND OTHER + 5
PROVIDED WITH THIS EQUIPMENT. INCLUDING AUX POWER) ALL OTHER DEVICES ADDRESSABLE • RESPONSE, ZONES 1-8: 10, 350, OR 700 MSEC
STEADY FOR BURGLARY/PANIC, DRAWING POWER DEVICES AND/OR RELAY
(PROGRAMMABLE) AUX PWR PROGRAM RELAY
TEMPORAL PULSE SOUNDING FROM TERMS 4 & 5 EXPANDER MODULES OUTPUT BLK _ + RED

Copyright © 2008 Honeywell International Inc.


FOR FIRE. CAN USE ADEMCO MUST BE INCLUDED 12 13 14 • MAXIMUM NUMBER OF 2-WIRE SMOKE DETECTORS AS ZONE TYPE 54
CONNECTION OF THE FIRE ALARM SIGNAL (UP TO 40 TERMINALS (FIRE ZONE RESET)
No. 702 SIREN, OR 12V BELL). IN AUX CURRENT ON ZONE 1 IS 16; DETECTORS MUST HAVE EOL
ZONE 1 CAN BE USED FOR 2-WIRE SMOKE DETECTORS
TO A FIRE ALARM HEADQUARTERS OR A ADDITIONAL ZONES) POWER
SEE INSTRUCTIONS. DRAIN CALCULATIONS. 4219, 4229, 4204: SET COMPATIBILITY IDENTIFIER AS "A". _ 4
CENTRAL STATION SHALL BE PERMITTED N.O. SUPERVISION
N.C.
ONLY WITH THE PERMISSION OF THE LOCAL DIP SW ADDR. 7-15 OR RELAY MODULE
AUTHORITY HAVING JURISDICTION. 5881: SET DIP SW TO TAMPER ZONE CONTACT OPENS MOMENTARILY A77-716B.
2k CONTACTS 2k PAIRS UPON FIRE ALARM RESET
THE BURGLAR ALARM SIGNAL SHALL NOT ADDR. "0". USE N.O.
BE CONNECTED TO A POLICE EMERGENCY SEE MODULE'S 10 11 CONTACT,
2 / 10 POWER SHUTDOWN NOTE: VIOLET WHICH CLOSES
NUMBER. INSTRUCTIONS TO OUTPUT 17 +
3 / 11 SYSTEM SHUTS DOWN PROGRAM OUTPUT 17 FOR _ WHEN POWER
ZONE 2 "OUT NORM LOW" = YES IN 4-WIRE SMOKE IS APPLIED.
4 / 12 SENSOR DETECTION 79 MENU MODE AND AS ZONE
WEEKLY TESTING IS REQUIRED TO ENSURE PROPER REMOTE KEYPADS OR COMBUSTION 2000
2k TAMPER 2k 5 / 13 PROCESSING IF TYPE 54 IN 80 MENU MODE DETECTOR OHMS
OPERATION OF THIS SYSTEM. IN ADDITION, THIS CAN USE 6150 OR 6160 CONTACTS 6 / 14 MAX. CURRENT = 100 mA
KEYPADS. LOCAL 3k CONTROL'S VOLTAGE EOLR
SYSTEM MUST BE CHECKED BY A QUALIFIED 7 / 15 (UP TO 16 DETECTORS
PROGRAMMING DROPS BELOW 9.6V. PLUS EOL MODULE)
TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS. 8 / 16
MUST BE DONE WITH A ZONE 10 TO ZONE TERM. ( +)
6139/6160, BUT NEED NOT HEAT
2k 2k DETECTOR
REMAIN IN THE SYSTEM 6.2k TO ZONE TERM. ( _)
ZONE 3 ZONE 4
(SET TO ADDRESS 16).
TYPICAL WIRING FOR TYPICAL WIRING FOR
DOUBLE BALANCED ZONE ZONE DOUBLING
COMPLIES WITH FCC RULES, PART 68. FCC REGISTRATION ASSEMBLED IN MEXICO
NO. 5GBUSA-44003-AL-E RINGER EQUIVALENCE: 0.1B. ADEMCO VISTA-21iP / VISTA-21iPSIA
SUMMARY OF CONNECTIONS

You might also like