Scribd
Upload
1K views

Welding Wire Diameter CHART PDF

This document provides guidance on selecting the proper wire type, size, and gas for MIG welding different materials and thicknesses. For the wire, use stainless steel wire for stainless steel, aluminum wire for aluminum, and steel wire for steel. Choose a smaller diameter wire for thinner materials and a larger wire for thicker materials. Refer to the included wire thickness chart for recommended wire diameters based on material thickness. For gas selection, the shielding gas protects the weld from atmospheric contamination. Use carbon dioxide gas for steel welding and argon-carbon dioxide mix for thin metals, as it provides better weldability and tolerance.

Uploaded by

Ferhat Kahveci
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

Welding Wire Diameter CHART PDF

This document provides guidance on selecting the proper wire type, size, and gas for MIG welding different materials and thicknesses. For the wire, use stainless steel wire for stainless steel, aluminum wire for aluminum, and steel wire for steel. Choose a smaller diameter wire for thinner materials and a larger wire for thicker materials. Refer to the included wire thickness chart for recommended wire diameters based on material thickness. For gas selection, the shielding gas protects the weld from atmospheric contamination. Use carbon dioxide gas for steel welding and argon-carbon dioxide mix for thin metals, as it provides better weldability and tolerance.

Uploaded by

Ferhat Kahveci
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Wire types and sizes - Use the correct wire type for the base metal being welded.

Use stainless
steel wire for stainless steel, aluminium wires for aluminium and steel wires for steel.

Use a smaller diameter wire for thin base metals. For thicker materials use a larger wire diameter
and larger machine, check the recommended welding capability of you machine.
As a guide refer to the “Welding Wire Thickness Chart” below.

WELDING WIRE DIAMETER CHART


RECOMMENDED WIRE DIAMETERS
MATERIAL MIG SOLID WIRE GASLESS FLUX CORED WIRE
THICKNESS 0.6mm 0.8mm 0.9mm 1.0mm 0.8mm 0.9mm 1.2mm
24 Gauge (.60mm)

22 Gauge (.75mm)

20 Gauge (.90mm)

18 Gauge (1.0mm)

16 Gauge (1.2mm)

14 Gauge (1.6mm)

3.0mm
5.0mm

6.0mm

8.0mm

10.mm

12.0mm

For material thickness of 5.0mm and greater, multi-pass runs or a beveled joint
design may be required depending on the amperage capability of your machine.

Gas selection - The purpose of the gas in the MIG process is to protect / shield the wire, the arc
and the molten weld metal from the atmosphere. Most metals when heated to a molten state will
react with the air in the atmosphere, without the protection of the shielding gas the weld produced
would contain defects like porosity, lack of fusion and slag inclusions. Additionally some of the
gas becomes ionised (electrically charged) and helps the current flow smoothly.
The correct gas flow is also very important in protecting the welding zone from the atmosphere.
Too low flow will give inadequate coverage and result in weld defects and unstable arc conditions.
Too high flow can cause air to be drawn into the gas column and contaminate the weld zone.
Use the correct shielding gas. Co2 is good for steel and offers good penetration characteristics,
the weld profile is narrower and slightly more raised than the weld profile obtained from Argon Co2
mixed gas. Argon Co2 mix gas offers better weld ability for thin metals and has a wider range of
setting tolerance on the machine. Argon 80% Co2 20% is a good all round mix suitable for most
applications.

Argon Co2 Co2

Penetration Pattern for Steel

26

You might also like